blob: 1ad24e4f0a85d3626098caff6c03cbd01a0a0aa2 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * mac53c94.h: definitions for the driver for the 53c94 SCSI bus adaptor
3 * found on Power Macintosh computers, controlling the external SCSI chain.
4 *
5 * Copyright (C) 1996 Paul Mackerras.
6 */
7#ifndef _MAC53C94_H
8#define _MAC53C94_H
9
10/*
11 * Registers in the 53C94 controller.
12 */
13
14struct mac53c94_regs {
15 unsigned char count_lo;
16 char pad0[15];
17 unsigned char count_mid;
18 char pad1[15];
19 unsigned char fifo;
20 char pad2[15];
21 unsigned char command;
22 char pad3[15];
23 unsigned char status;
24 char pad4[15];
25 unsigned char interrupt;
26 char pad5[15];
27 unsigned char seqstep;
28 char pad6[15];
29 unsigned char flags;
30 char pad7[15];
31 unsigned char config1;
32 char pad8[15];
33 unsigned char clk_factor;
34 char pad9[15];
35 unsigned char test;
36 char pad10[15];
37 unsigned char config2;
38 char pad11[15];
39 unsigned char config3;
40 char pad12[15];
41 unsigned char config4;
42 char pad13[15];
43 unsigned char count_hi;
44 char pad14[15];
45 unsigned char fifo_res;
46 char pad15[15];
47};
48
49/*
50 * Alternate functions for some registers.
51 */
52#define dest_id status
53#define sel_timeout interrupt
54#define sync_period seqstep
55#define sync_offset flags
56
57/*
58 * Bits in command register.
59 */
60#define CMD_DMA_MODE 0x80
61#define CMD_MODE_MASK 0x70
62#define CMD_MODE_INIT 0x10
63#define CMD_MODE_TARG 0x20
64#define CMD_MODE_DISC 0x40
65
66#define CMD_NOP 0
67#define CMD_FLUSH 1
68#define CMD_RESET 2
69#define CMD_SCSI_RESET 3
70
71#define CMD_XFER_DATA 0x10
72#define CMD_I_COMPLETE 0x11
73#define CMD_ACCEPT_MSG 0x12
74#define CMD_XFER_PAD 0x18
75#define CMD_SET_ATN 0x1a
76#define CMD_CLR_ATN 0x1b
77
78#define CMD_SEND_MSG 0x20
79#define CMD_SEND_STATUS 0x21
80#define CMD_SEND_DATA 0x22
81#define CMD_DISC_SEQ 0x23
82#define CMD_TERMINATE 0x24
83#define CMD_T_COMPLETE 0x25
84#define CMD_DISCONNECT 0x27
85#define CMD_RECV_MSG 0x28
86#define CMD_RECV_CDB 0x29
87#define CMD_RECV_DATA 0x2a
88#define CMD_RECV_CMD 0x2b
89#define CMD_ABORT_DMA 0x04
90
91#define CMD_RESELECT 0x40
92#define CMD_SELECT 0x41
93#define CMD_SELECT_ATN 0x42
94#define CMD_SELATN_STOP 0x43
95#define CMD_ENABLE_SEL 0x44
96#define CMD_DISABLE_SEL 0x45
97#define CMD_SEL_ATN3 0x46
98#define CMD_RESEL_ATN3 0x47
99
100/*
101 * Bits in status register.
102 */
103#define STAT_IRQ 0x80
104#define STAT_ERROR 0x40
105#define STAT_PARITY 0x20
106#define STAT_TC_ZERO 0x10
107#define STAT_DONE 0x08
108#define STAT_PHASE 0x07
109#define STAT_MSG 0x04
110#define STAT_CD 0x02
111#define STAT_IO 0x01
112
113/*
114 * Bits in interrupt register.
115 */
116#define INTR_RESET 0x80 /* SCSI bus was reset */
117#define INTR_ILL_CMD 0x40 /* illegal command */
118#define INTR_DISCONNECT 0x20 /* we got disconnected */
119#define INTR_BUS_SERV 0x10 /* bus service requested */
120#define INTR_DONE 0x08 /* function completed */
121#define INTR_RESELECTED 0x04 /* we were reselected */
122#define INTR_SEL_ATN 0x02 /* we were selected, ATN asserted */
123#define INTR_SELECT 0x01 /* we were selected, ATN negated */
124
125/*
126 * Encoding for the select timeout.
127 */
128#define TIMO_VAL(x) ((x) * 5000 / 7682)
129
130/*
131 * Bits in sequence step register.
132 */
133#define SS_MASK 7
134#define SS_ARB_SEL 0 /* Selection & arbitration complete */
135#define SS_MSG_SENT 1 /* One message byte sent */
136#define SS_NOT_CMD 2 /* Not in command phase */
137#define SS_PHASE_CHG 3 /* Early phase change, cmd bytes lost */
138#define SS_DONE 4 /* Command was sent OK */
139
140/*
141 * Encoding for sync transfer period.
142 */
143#define SYNCP_MASK 0x1f
144#define SYNCP_MIN 4
145#define SYNCP_MAX 31
146
147/*
148 * Bits in flags register.
149 */
150#define FLAGS_FIFO_LEV 0x1f
151#define FLAGS_SEQ_STEP 0xe0
152
153/*
154 * Encoding for sync offset.
155 */
156#define SYNCO_MASK 0x0f
157#define SYNCO_ASS_CTRL 0x30 /* REQ/ACK assertion control */
158#define SYNCO_NEG_CTRL 0xc0 /* REQ/ACK negation control */
159
160/*
161 * Bits in config1 register.
162 */
163#define CF1_SLOW_CABLE 0x80 /* Slow cable mode */
164#define CF1_NO_RES_REP 0x40 /* Disable SCSI reset reports */
165#define CF1_PAR_TEST 0x20 /* Parity test mode enable */
166#define CF1_PAR_ENABLE 0x10 /* Enable parity checks */
167#define CF1_TEST 0x08 /* Chip tests */
168#define CF1_MY_ID 0x07 /* Controller's address on bus */
169
170/*
171 * Encoding for clk_factor register.
172 */
173#define CLKF_MASK 7
174#define CLKF_VAL(freq) ((((freq) + 4999999) / 5000000) & CLKF_MASK)
175
176/*
177 * Bits in test mode register.
178 */
179#define TEST_TARGET 1 /* target test mode */
180#define TEST_INITIATOR 2 /* initiator test mode */
181#define TEST_TRISTATE 4 /* tristate (hi-z) test mode */
182
183/*
184 * Bits in config2 register.
185 */
186#define CF2_RFB 0x80
187#define CF2_FEATURE_EN 0x40 /* enable features / phase latch */
188#define CF2_BYTECTRL 0x20
189#define CF2_DREQ_HIZ 0x10
190#define CF2_SCSI2 0x08
191#define CF2_PAR_ABORT 0x04 /* bad parity target abort */
192#define CF2_REG_PARERR 0x02 /* register parity error */
193#define CF2_DMA_PARERR 0x01 /* DMA parity error */
194
195/*
196 * Bits in the config3 register.
197 */
198#define CF3_ID_MSG_CHK 0x80
199#define CF3_3B_MSGS 0x40
200#define CF3_CDB10 0x20
201#define CF3_FASTSCSI 0x10 /* enable fast SCSI support */
202#define CF3_FASTCLOCK 0x08
203#define CF3_SAVERESID 0x04
204#define CF3_ALT_DMA 0x02
205#define CF3_THRESH_8 0x01
206
207/*
208 * Bits in the config4 register.
209 */
210#define CF4_EAN 0x04
211#define CF4_TEST 0x02
212#define CF4_BBTE 0x01
213
214#endif /* _MAC53C94_H */