blob: 6fcfe99bd999d295e0eb8efb967d0b2892335afc [file] [log] [blame]
Michael Buesch61e115a2007-09-18 15:12:50 -04001#ifndef LINUX_SSB_CHIPCO_H_
2#define LINUX_SSB_CHIPCO_H_
3
4/* SonicsSiliconBackplane CHIPCOMMON core hardware definitions
5 *
6 * The chipcommon core provides chip identification, SB control,
7 * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
8 * gpio interface, extbus, and support for serial and parallel flashes.
9 *
10 * Copyright 2005, Broadcom Corporation
Michael Büscheb032b92011-07-04 20:50:05 +020011 * Copyright 2006, Michael Buesch <m@bues.ch>
Michael Buesch61e115a2007-09-18 15:12:50 -040012 *
13 * Licensed under the GPL version 2. See COPYING for details.
14 */
15
16/** ChipCommon core registers. **/
17
18#define SSB_CHIPCO_CHIPID 0x0000
19#define SSB_CHIPCO_IDMASK 0x0000FFFF
20#define SSB_CHIPCO_REVMASK 0x000F0000
21#define SSB_CHIPCO_REVSHIFT 16
22#define SSB_CHIPCO_PACKMASK 0x00F00000
23#define SSB_CHIPCO_PACKSHIFT 20
24#define SSB_CHIPCO_NRCORESMASK 0x0F000000
25#define SSB_CHIPCO_NRCORESSHIFT 24
26#define SSB_CHIPCO_CAP 0x0004 /* Capabilities */
27#define SSB_CHIPCO_CAP_NRUART 0x00000003 /* # of UARTs */
28#define SSB_CHIPCO_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */
29#define SSB_CHIPCO_CAP_UARTCLK 0x00000018 /* UART clock select */
30#define SSB_CHIPCO_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */
31#define SSB_CHIPCO_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */
32#define SSB_CHIPCO_CAP_EXTBUS 0x000000C0 /* External buses present */
33#define SSB_CHIPCO_CAP_FLASHT 0x00000700 /* Flash Type */
34#define SSB_CHIPCO_FLASHT_NONE 0x00000000 /* No flash */
35#define SSB_CHIPCO_FLASHT_STSER 0x00000100 /* ST serial flash */
36#define SSB_CHIPCO_FLASHT_ATSER 0x00000200 /* Atmel serial flash */
37#define SSB_CHIPCO_FLASHT_PARA 0x00000700 /* Parallel flash */
38#define SSB_CHIPCO_CAP_PLLT 0x00038000 /* PLL Type */
39#define SSB_PLLTYPE_NONE 0x00000000
40#define SSB_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */
41#define SSB_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */
42#define SSB_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */
43#define SSB_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */
44#define SSB_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */
45#define SSB_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */
46#define SSB_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */
47#define SSB_CHIPCO_CAP_PCTL 0x00040000 /* Power Control */
48#define SSB_CHIPCO_CAP_OTPS 0x00380000 /* OTP size */
49#define SSB_CHIPCO_CAP_OTPS_SHIFT 19
50#define SSB_CHIPCO_CAP_OTPS_BASE 5
51#define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */
52#define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */
53#define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */
Michael Buesch58ff70d2008-02-18 21:44:39 +010054#define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
55#define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
John W. Linvilled53cdbb2010-03-31 21:39:35 +020056#define SSB_CHIPCO_CAP_SPROM 0x40000000 /* SPROM present */
Michael Buesch61e115a2007-09-18 15:12:50 -040057#define SSB_CHIPCO_CORECTL 0x0008
58#define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
59#define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
Michael Buesch58ff70d2008-02-18 21:44:39 +010060#define SSB_CHIPCO_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */
Michael Buesch61e115a2007-09-18 15:12:50 -040061#define SSB_CHIPCO_BIST 0x000C
62#define SSB_CHIPCO_OTPS 0x0010 /* OTP status */
63#define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000
64#define SSB_CHIPCO_OTPS_PROTECT 0x00000007
65#define SSB_CHIPCO_OTPS_HW_PROTECT 0x00000001
66#define SSB_CHIPCO_OTPS_SW_PROTECT 0x00000002
67#define SSB_CHIPCO_OTPS_CID_PROTECT 0x00000004
68#define SSB_CHIPCO_OTPC 0x0014 /* OTP control */
69#define SSB_CHIPCO_OTPC_RECWAIT 0xFF000000
70#define SSB_CHIPCO_OTPC_PROGWAIT 0x00FFFF00
71#define SSB_CHIPCO_OTPC_PRW_SHIFT 8
72#define SSB_CHIPCO_OTPC_MAXFAIL 0x00000038
73#define SSB_CHIPCO_OTPC_VSEL 0x00000006
74#define SSB_CHIPCO_OTPC_SELVL 0x00000001
75#define SSB_CHIPCO_OTPP 0x0018 /* OTP prog */
76#define SSB_CHIPCO_OTPP_COL 0x000000FF
77#define SSB_CHIPCO_OTPP_ROW 0x0000FF00
78#define SSB_CHIPCO_OTPP_ROW_SHIFT 8
79#define SSB_CHIPCO_OTPP_READERR 0x10000000
80#define SSB_CHIPCO_OTPP_VALUE 0x20000000
81#define SSB_CHIPCO_OTPP_READ 0x40000000
82#define SSB_CHIPCO_OTPP_START 0x80000000
83#define SSB_CHIPCO_OTPP_BUSY 0x80000000
84#define SSB_CHIPCO_IRQSTAT 0x0020
85#define SSB_CHIPCO_IRQMASK 0x0024
86#define SSB_CHIPCO_IRQ_GPIO 0x00000001 /* gpio intr */
87#define SSB_CHIPCO_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */
88#define SSB_CHIPCO_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */
89#define SSB_CHIPCO_CHIPCTL 0x0028 /* Rev >= 11 only */
90#define SSB_CHIPCO_CHIPSTAT 0x002C /* Rev >= 11 only */
91#define SSB_CHIPCO_JCMD 0x0030 /* Rev >= 10 only */
92#define SSB_CHIPCO_JCMD_START 0x80000000
93#define SSB_CHIPCO_JCMD_BUSY 0x80000000
94#define SSB_CHIPCO_JCMD_PAUSE 0x40000000
95#define SSB_CHIPCO_JCMD0_ACC_MASK 0x0000F000
96#define SSB_CHIPCO_JCMD0_ACC_IRDR 0x00000000
97#define SSB_CHIPCO_JCMD0_ACC_DR 0x00001000
98#define SSB_CHIPCO_JCMD0_ACC_IR 0x00002000
99#define SSB_CHIPCO_JCMD0_ACC_RESET 0x00003000
100#define SSB_CHIPCO_JCMD0_ACC_IRPDR 0x00004000
101#define SSB_CHIPCO_JCMD0_ACC_PDR 0x00005000
102#define SSB_CHIPCO_JCMD0_IRW_MASK 0x00000F00
103#define SSB_CHIPCO_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */
104#define SSB_CHIPCO_JCMD_ACC_IRDR 0x00000000
105#define SSB_CHIPCO_JCMD_ACC_DR 0x00010000
106#define SSB_CHIPCO_JCMD_ACC_IR 0x00020000
107#define SSB_CHIPCO_JCMD_ACC_RESET 0x00030000
108#define SSB_CHIPCO_JCMD_ACC_IRPDR 0x00040000
109#define SSB_CHIPCO_JCMD_ACC_PDR 0x00050000
110#define SSB_CHIPCO_JCMD_IRW_MASK 0x00001F00
111#define SSB_CHIPCO_JCMD_IRW_SHIFT 8
112#define SSB_CHIPCO_JCMD_DRW_MASK 0x0000003F
113#define SSB_CHIPCO_JIR 0x0034 /* Rev >= 10 only */
114#define SSB_CHIPCO_JDR 0x0038 /* Rev >= 10 only */
115#define SSB_CHIPCO_JCTL 0x003C /* Rev >= 10 only */
116#define SSB_CHIPCO_JCTL_FORCE_CLK 4 /* Force clock */
117#define SSB_CHIPCO_JCTL_EXT_EN 2 /* Enable external targets */
118#define SSB_CHIPCO_JCTL_EN 1 /* Enable Jtag master */
119#define SSB_CHIPCO_FLASHCTL 0x0040
120#define SSB_CHIPCO_FLASHCTL_START 0x80000000
121#define SSB_CHIPCO_FLASHCTL_BUSY SSB_CHIPCO_FLASHCTL_START
122#define SSB_CHIPCO_FLASHADDR 0x0044
123#define SSB_CHIPCO_FLASHDATA 0x0048
124#define SSB_CHIPCO_BCAST_ADDR 0x0050
125#define SSB_CHIPCO_BCAST_DATA 0x0054
Rafał Miłecki9835a302011-04-24 11:04:19 +0200126#define SSB_CHIPCO_GPIOPULLUP 0x0058 /* Rev >= 20 only */
127#define SSB_CHIPCO_GPIOPULLDOWN 0x005C /* Rev >= 20 only */
Michael Buesch61e115a2007-09-18 15:12:50 -0400128#define SSB_CHIPCO_GPIOIN 0x0060
129#define SSB_CHIPCO_GPIOOUT 0x0064
130#define SSB_CHIPCO_GPIOOUTEN 0x0068
131#define SSB_CHIPCO_GPIOCTL 0x006C
132#define SSB_CHIPCO_GPIOPOL 0x0070
133#define SSB_CHIPCO_GPIOIRQ 0x0074
134#define SSB_CHIPCO_WATCHDOG 0x0080
135#define SSB_CHIPCO_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */
Rafał Miłecki9f2e7312011-04-20 11:12:30 +0200136#define SSB_CHIPCO_GPIOTIMER_OFFTIME 0x0000FFFF
137#define SSB_CHIPCO_GPIOTIMER_OFFTIME_SHIFT 0
138#define SSB_CHIPCO_GPIOTIMER_ONTIME 0xFFFF0000
Michael Buesch61e115a2007-09-18 15:12:50 -0400139#define SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT 16
140#define SSB_CHIPCO_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */
141#define SSB_CHIPCO_CLOCK_N 0x0090
142#define SSB_CHIPCO_CLOCK_SB 0x0094
143#define SSB_CHIPCO_CLOCK_PCI 0x0098
144#define SSB_CHIPCO_CLOCK_M2 0x009C
145#define SSB_CHIPCO_CLOCK_MIPS 0x00A0
146#define SSB_CHIPCO_CLKDIV 0x00A4 /* Rev >= 3 only */
147#define SSB_CHIPCO_CLKDIV_SFLASH 0x0F000000
148#define SSB_CHIPCO_CLKDIV_SFLASH_SHIFT 24
149#define SSB_CHIPCO_CLKDIV_OTP 0x000F0000
150#define SSB_CHIPCO_CLKDIV_OTP_SHIFT 16
151#define SSB_CHIPCO_CLKDIV_JTAG 0x00000F00
152#define SSB_CHIPCO_CLKDIV_JTAG_SHIFT 8
153#define SSB_CHIPCO_CLKDIV_UART 0x000000FF
154#define SSB_CHIPCO_PLLONDELAY 0x00B0 /* Rev >= 4 only */
155#define SSB_CHIPCO_FREFSELDELAY 0x00B4 /* Rev >= 4 only */
156#define SSB_CHIPCO_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */
157#define SSB_CHIPCO_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */
158#define SSB_CHIPCO_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */
159#define SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */
160#define SSB_CHIPCO_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */
161#define SSB_CHIPCO_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */
162#define SSB_CHIPCO_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */
163#define SSB_CHIPCO_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */
164#define SSB_CHIPCO_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */
165#define SSB_CHIPCO_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */
166#define SSB_CHIPCO_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */
167#define SSB_CHIPCO_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */
168#define SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT 16
169#define SSB_CHIPCO_SYSCLKCTL 0x00C0 /* Rev >= 3 only */
170#define SSB_CHIPCO_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */
171#define SSB_CHIPCO_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */
172#define SSB_CHIPCO_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */
173#define SSB_CHIPCO_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */
174#define SSB_CHIPCO_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */
175#define SSB_CHIPCO_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */
176#define SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT 16
177#define SSB_CHIPCO_CLKSTSTR 0x00C4 /* Rev >= 3 only */
178#define SSB_CHIPCO_PCMCIA_CFG 0x0100
179#define SSB_CHIPCO_PCMCIA_MEMWAIT 0x0104
180#define SSB_CHIPCO_PCMCIA_ATTRWAIT 0x0108
181#define SSB_CHIPCO_PCMCIA_IOWAIT 0x010C
182#define SSB_CHIPCO_IDE_CFG 0x0110
183#define SSB_CHIPCO_IDE_MEMWAIT 0x0114
184#define SSB_CHIPCO_IDE_ATTRWAIT 0x0118
185#define SSB_CHIPCO_IDE_IOWAIT 0x011C
186#define SSB_CHIPCO_PROG_CFG 0x0120
187#define SSB_CHIPCO_PROG_WAITCNT 0x0124
188#define SSB_CHIPCO_FLASH_CFG 0x0128
189#define SSB_CHIPCO_FLASH_WAITCNT 0x012C
Michael Bueschc9703142009-02-03 19:23:18 +0100190#define SSB_CHIPCO_CLKCTLST 0x01E0 /* Clock control and status (rev >= 20) */
191#define SSB_CHIPCO_CLKCTLST_FORCEALP 0x00000001 /* Force ALP request */
192#define SSB_CHIPCO_CLKCTLST_FORCEHT 0x00000002 /* Force HT request */
193#define SSB_CHIPCO_CLKCTLST_FORCEILP 0x00000004 /* Force ILP request */
194#define SSB_CHIPCO_CLKCTLST_HAVEALPREQ 0x00000008 /* ALP available request */
195#define SSB_CHIPCO_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */
196#define SSB_CHIPCO_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */
Rafał Miłecki9f2e7312011-04-20 11:12:30 +0200197#define SSB_CHIPCO_CLKCTLST_HAVEALP 0x00010000 /* ALP available */
198#define SSB_CHIPCO_CLKCTLST_HAVEHT 0x00020000 /* HT available */
199#define SSB_CHIPCO_CLKCTLST_4328A0_HAVEHT 0x00010000 /* 4328a0 has reversed bits */
200#define SSB_CHIPCO_CLKCTLST_4328A0_HAVEALP 0x00020000 /* 4328a0 has reversed bits */
Michael Bueschc9703142009-02-03 19:23:18 +0100201#define SSB_CHIPCO_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */
Michael Buesch61e115a2007-09-18 15:12:50 -0400202#define SSB_CHIPCO_UART0_DATA 0x0300
203#define SSB_CHIPCO_UART0_IMR 0x0304
204#define SSB_CHIPCO_UART0_FCR 0x0308
205#define SSB_CHIPCO_UART0_LCR 0x030C
206#define SSB_CHIPCO_UART0_MCR 0x0310
207#define SSB_CHIPCO_UART0_LSR 0x0314
208#define SSB_CHIPCO_UART0_MSR 0x0318
209#define SSB_CHIPCO_UART0_SCRATCH 0x031C
210#define SSB_CHIPCO_UART1_DATA 0x0400
211#define SSB_CHIPCO_UART1_IMR 0x0404
212#define SSB_CHIPCO_UART1_FCR 0x0408
213#define SSB_CHIPCO_UART1_LCR 0x040C
214#define SSB_CHIPCO_UART1_MCR 0x0410
215#define SSB_CHIPCO_UART1_LSR 0x0414
216#define SSB_CHIPCO_UART1_MSR 0x0418
217#define SSB_CHIPCO_UART1_SCRATCH 0x041C
Michael Bueschc9703142009-02-03 19:23:18 +0100218/* PMU registers (rev >= 20) */
219#define SSB_CHIPCO_PMU_CTL 0x0600 /* PMU control */
220#define SSB_CHIPCO_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */
221#define SSB_CHIPCO_PMU_CTL_ILP_DIV_SHIFT 16
Rafał Miłecki46fc4c92013-04-02 15:57:26 +0200222#define SSB_CHIPCO_PMU_CTL_PLL_UPD 0x00000400
Michael Bueschc9703142009-02-03 19:23:18 +0100223#define SSB_CHIPCO_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */
224#define SSB_CHIPCO_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */
225#define SSB_CHIPCO_PMU_CTL_ALPREQEN 0x00000080 /* ALP req enable */
226#define SSB_CHIPCO_PMU_CTL_XTALFREQ 0x0000007C /* Crystal freq */
227#define SSB_CHIPCO_PMU_CTL_XTALFREQ_SHIFT 2
228#define SSB_CHIPCO_PMU_CTL_ILPDIVEN 0x00000002 /* ILP div enable */
229#define SSB_CHIPCO_PMU_CTL_LPOSEL 0x00000001 /* LPO sel */
230#define SSB_CHIPCO_PMU_CAP 0x0604 /* PMU capabilities */
231#define SSB_CHIPCO_PMU_CAP_REVISION 0x000000FF /* Revision mask */
232#define SSB_CHIPCO_PMU_STAT 0x0608 /* PMU status */
233#define SSB_CHIPCO_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */
234#define SSB_CHIPCO_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */
235#define SSB_CHIPCO_PMU_STAT_HAVEALP 0x00000008 /* ALP available */
236#define SSB_CHIPCO_PMU_STAT_HAVEHT 0x00000004 /* HT available */
237#define SSB_CHIPCO_PMU_STAT_RESINIT 0x00000003 /* Res init */
238#define SSB_CHIPCO_PMU_RES_STAT 0x060C /* PMU res status */
239#define SSB_CHIPCO_PMU_RES_PEND 0x0610 /* PMU res pending */
240#define SSB_CHIPCO_PMU_TIMER 0x0614 /* PMU timer */
241#define SSB_CHIPCO_PMU_MINRES_MSK 0x0618 /* PMU min res mask */
242#define SSB_CHIPCO_PMU_MAXRES_MSK 0x061C /* PMU max res mask */
243#define SSB_CHIPCO_PMU_RES_TABSEL 0x0620 /* PMU res table sel */
244#define SSB_CHIPCO_PMU_RES_DEPMSK 0x0624 /* PMU res dep mask */
245#define SSB_CHIPCO_PMU_RES_UPDNTM 0x0628 /* PMU res updown timer */
246#define SSB_CHIPCO_PMU_RES_TIMER 0x062C /* PMU res timer */
247#define SSB_CHIPCO_PMU_CLKSTRETCH 0x0630 /* PMU clockstretch */
248#define SSB_CHIPCO_PMU_WATCHDOG 0x0634 /* PMU watchdog */
249#define SSB_CHIPCO_PMU_RES_REQTS 0x0640 /* PMU res req timer sel */
250#define SSB_CHIPCO_PMU_RES_REQT 0x0644 /* PMU res req timer */
251#define SSB_CHIPCO_PMU_RES_REQM 0x0648 /* PMU res req mask */
252#define SSB_CHIPCO_CHIPCTL_ADDR 0x0650
253#define SSB_CHIPCO_CHIPCTL_DATA 0x0654
254#define SSB_CHIPCO_REGCTL_ADDR 0x0658
255#define SSB_CHIPCO_REGCTL_DATA 0x065C
256#define SSB_CHIPCO_PLLCTL_ADDR 0x0660
257#define SSB_CHIPCO_PLLCTL_DATA 0x0664
258
259
260
261/** PMU PLL registers */
262
263/* PMU rev 0 PLL registers */
264#define SSB_PMU0_PLLCTL0 0
265#define SSB_PMU0_PLLCTL0_PDIV_MSK 0x00000001
266#define SSB_PMU0_PLLCTL0_PDIV_FREQ 25000 /* kHz */
267#define SSB_PMU0_PLLCTL1 1
268#define SSB_PMU0_PLLCTL1_WILD_IMSK 0xF0000000 /* Wild int mask (low nibble) */
269#define SSB_PMU0_PLLCTL1_WILD_IMSK_SHIFT 28
270#define SSB_PMU0_PLLCTL1_WILD_FMSK 0x0FFFFF00 /* Wild frac mask */
271#define SSB_PMU0_PLLCTL1_WILD_FMSK_SHIFT 8
272#define SSB_PMU0_PLLCTL1_STOPMOD 0x00000040 /* Stop mod */
273#define SSB_PMU0_PLLCTL2 2
274#define SSB_PMU0_PLLCTL2_WILD_IMSKHI 0x0000000F /* Wild int mask (high nibble) */
275#define SSB_PMU0_PLLCTL2_WILD_IMSKHI_SHIFT 0
276
277/* PMU rev 1 PLL registers */
278#define SSB_PMU1_PLLCTL0 0
279#define SSB_PMU1_PLLCTL0_P1DIV 0x00F00000 /* P1 div */
280#define SSB_PMU1_PLLCTL0_P1DIV_SHIFT 20
281#define SSB_PMU1_PLLCTL0_P2DIV 0x0F000000 /* P2 div */
282#define SSB_PMU1_PLLCTL0_P2DIV_SHIFT 24
283#define SSB_PMU1_PLLCTL1 1
284#define SSB_PMU1_PLLCTL1_M1DIV 0x000000FF /* M1 div */
285#define SSB_PMU1_PLLCTL1_M1DIV_SHIFT 0
286#define SSB_PMU1_PLLCTL1_M2DIV 0x0000FF00 /* M2 div */
287#define SSB_PMU1_PLLCTL1_M2DIV_SHIFT 8
288#define SSB_PMU1_PLLCTL1_M3DIV 0x00FF0000 /* M3 div */
289#define SSB_PMU1_PLLCTL1_M3DIV_SHIFT 16
290#define SSB_PMU1_PLLCTL1_M4DIV 0xFF000000 /* M4 div */
291#define SSB_PMU1_PLLCTL1_M4DIV_SHIFT 24
292#define SSB_PMU1_PLLCTL2 2
293#define SSB_PMU1_PLLCTL2_M5DIV 0x000000FF /* M5 div */
294#define SSB_PMU1_PLLCTL2_M5DIV_SHIFT 0
295#define SSB_PMU1_PLLCTL2_M6DIV 0x0000FF00 /* M6 div */
296#define SSB_PMU1_PLLCTL2_M6DIV_SHIFT 8
297#define SSB_PMU1_PLLCTL2_NDIVMODE 0x000E0000 /* NDIV mode */
298#define SSB_PMU1_PLLCTL2_NDIVMODE_SHIFT 17
299#define SSB_PMU1_PLLCTL2_NDIVINT 0x1FF00000 /* NDIV int */
300#define SSB_PMU1_PLLCTL2_NDIVINT_SHIFT 20
301#define SSB_PMU1_PLLCTL3 3
302#define SSB_PMU1_PLLCTL3_NDIVFRAC 0x00FFFFFF /* NDIV frac */
303#define SSB_PMU1_PLLCTL3_NDIVFRAC_SHIFT 0
304#define SSB_PMU1_PLLCTL4 4
305#define SSB_PMU1_PLLCTL5 5
306#define SSB_PMU1_PLLCTL5_CLKDRV 0xFFFFFF00 /* clk drv */
307#define SSB_PMU1_PLLCTL5_CLKDRV_SHIFT 8
308
309/* BCM4312 PLL resource numbers. */
310#define SSB_PMURES_4312_SWITCHER_BURST 0
311#define SSB_PMURES_4312_SWITCHER_PWM 1
312#define SSB_PMURES_4312_PA_REF_LDO 2
313#define SSB_PMURES_4312_CORE_LDO_BURST 3
314#define SSB_PMURES_4312_CORE_LDO_PWM 4
315#define SSB_PMURES_4312_RADIO_LDO 5
316#define SSB_PMURES_4312_ILP_REQUEST 6
317#define SSB_PMURES_4312_BG_FILTBYP 7
318#define SSB_PMURES_4312_TX_FILTBYP 8
319#define SSB_PMURES_4312_RX_FILTBYP 9
320#define SSB_PMURES_4312_XTAL_PU 10
321#define SSB_PMURES_4312_ALP_AVAIL 11
322#define SSB_PMURES_4312_BB_PLL_FILTBYP 12
323#define SSB_PMURES_4312_RF_PLL_FILTBYP 13
324#define SSB_PMURES_4312_HT_AVAIL 14
325
326/* BCM4325 PLL resource numbers. */
327#define SSB_PMURES_4325_BUCK_BOOST_BURST 0
328#define SSB_PMURES_4325_CBUCK_BURST 1
329#define SSB_PMURES_4325_CBUCK_PWM 2
330#define SSB_PMURES_4325_CLDO_CBUCK_BURST 3
331#define SSB_PMURES_4325_CLDO_CBUCK_PWM 4
332#define SSB_PMURES_4325_BUCK_BOOST_PWM 5
333#define SSB_PMURES_4325_ILP_REQUEST 6
334#define SSB_PMURES_4325_ABUCK_BURST 7
335#define SSB_PMURES_4325_ABUCK_PWM 8
336#define SSB_PMURES_4325_LNLDO1_PU 9
337#define SSB_PMURES_4325_LNLDO2_PU 10
338#define SSB_PMURES_4325_LNLDO3_PU 11
339#define SSB_PMURES_4325_LNLDO4_PU 12
340#define SSB_PMURES_4325_XTAL_PU 13
341#define SSB_PMURES_4325_ALP_AVAIL 14
342#define SSB_PMURES_4325_RX_PWRSW_PU 15
343#define SSB_PMURES_4325_TX_PWRSW_PU 16
344#define SSB_PMURES_4325_RFPLL_PWRSW_PU 17
345#define SSB_PMURES_4325_LOGEN_PWRSW_PU 18
346#define SSB_PMURES_4325_AFE_PWRSW_PU 19
347#define SSB_PMURES_4325_BBPLL_PWRSW_PU 20
348#define SSB_PMURES_4325_HT_AVAIL 21
349
350/* BCM4328 PLL resource numbers. */
351#define SSB_PMURES_4328_EXT_SWITCHER_PWM 0
352#define SSB_PMURES_4328_BB_SWITCHER_PWM 1
353#define SSB_PMURES_4328_BB_SWITCHER_BURST 2
354#define SSB_PMURES_4328_BB_EXT_SWITCHER_BURST 3
355#define SSB_PMURES_4328_ILP_REQUEST 4
356#define SSB_PMURES_4328_RADIO_SWITCHER_PWM 5
357#define SSB_PMURES_4328_RADIO_SWITCHER_BURST 6
358#define SSB_PMURES_4328_ROM_SWITCH 7
359#define SSB_PMURES_4328_PA_REF_LDO 8
360#define SSB_PMURES_4328_RADIO_LDO 9
361#define SSB_PMURES_4328_AFE_LDO 10
362#define SSB_PMURES_4328_PLL_LDO 11
363#define SSB_PMURES_4328_BG_FILTBYP 12
364#define SSB_PMURES_4328_TX_FILTBYP 13
365#define SSB_PMURES_4328_RX_FILTBYP 14
366#define SSB_PMURES_4328_XTAL_PU 15
367#define SSB_PMURES_4328_XTAL_EN 16
368#define SSB_PMURES_4328_BB_PLL_FILTBYP 17
369#define SSB_PMURES_4328_RF_PLL_FILTBYP 18
370#define SSB_PMURES_4328_BB_PLL_PU 19
371
372/* BCM5354 PLL resource numbers. */
373#define SSB_PMURES_5354_EXT_SWITCHER_PWM 0
374#define SSB_PMURES_5354_BB_SWITCHER_PWM 1
375#define SSB_PMURES_5354_BB_SWITCHER_BURST 2
376#define SSB_PMURES_5354_BB_EXT_SWITCHER_BURST 3
377#define SSB_PMURES_5354_ILP_REQUEST 4
378#define SSB_PMURES_5354_RADIO_SWITCHER_PWM 5
379#define SSB_PMURES_5354_RADIO_SWITCHER_BURST 6
380#define SSB_PMURES_5354_ROM_SWITCH 7
381#define SSB_PMURES_5354_PA_REF_LDO 8
382#define SSB_PMURES_5354_RADIO_LDO 9
383#define SSB_PMURES_5354_AFE_LDO 10
384#define SSB_PMURES_5354_PLL_LDO 11
385#define SSB_PMURES_5354_BG_FILTBYP 12
386#define SSB_PMURES_5354_TX_FILTBYP 13
387#define SSB_PMURES_5354_RX_FILTBYP 14
388#define SSB_PMURES_5354_XTAL_PU 15
389#define SSB_PMURES_5354_XTAL_EN 16
390#define SSB_PMURES_5354_BB_PLL_FILTBYP 17
391#define SSB_PMURES_5354_RF_PLL_FILTBYP 18
392#define SSB_PMURES_5354_BB_PLL_PU 19
393
394
395
396/** Chip specific Chip-Status register contents. */
John W. Linvilled53cdbb2010-03-31 21:39:35 +0200397#define SSB_CHIPCO_CHST_4322_SPROM_EXISTS 0x00000040 /* SPROM present */
Michael Bueschc9703142009-02-03 19:23:18 +0100398#define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL 0x00000003
399#define SSB_CHIPCO_CHST_4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
400#define SSB_CHIPCO_CHST_4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
401#define SSB_CHIPCO_CHST_4325_OTP_SEL 2 /* OTP is powered up, no SPROM */
402#define SSB_CHIPCO_CHST_4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
403#define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE 0x00000004
404#define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE_SHIFT 2
405#define SSB_CHIPCO_CHST_4325_RCAL_VALID 0x00000008
406#define SSB_CHIPCO_CHST_4325_RCAL_VALID_SHIFT 3
407#define SSB_CHIPCO_CHST_4325_RCAL_VALUE 0x000001F0
408#define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT 4
409#define SSB_CHIPCO_CHST_4325_PMUTOP_2B 0x00000200 /* 1 for 2b, 0 for to 2a */
Michael Buesch61e115a2007-09-18 15:12:50 -0400410
John W. Linvilled53cdbb2010-03-31 21:39:35 +0200411/** Macros to determine SPROM presence based on Chip-Status register. */
412#define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \
413 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
414 SSB_CHIPCO_CHST_4325_OTP_SEL)
415#define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \
416 (status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS)
417#define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \
418 (((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
419 SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \
420 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
421 SSB_CHIPCO_CHST_4325_OTP_SEL))
422
Michael Buesch61e115a2007-09-18 15:12:50 -0400423
424
425/** Clockcontrol masks and values **/
426
427/* SSB_CHIPCO_CLOCK_N */
428#define SSB_CHIPCO_CLK_N1 0x0000003F /* n1 control */
429#define SSB_CHIPCO_CLK_N2 0x00003F00 /* n2 control */
430#define SSB_CHIPCO_CLK_N2_SHIFT 8
431#define SSB_CHIPCO_CLK_PLLC 0x000F0000 /* pll control */
432#define SSB_CHIPCO_CLK_PLLC_SHIFT 16
433
434/* SSB_CHIPCO_CLOCK_SB/PCI/UART */
435#define SSB_CHIPCO_CLK_M1 0x0000003F /* m1 control */
436#define SSB_CHIPCO_CLK_M2 0x00003F00 /* m2 control */
437#define SSB_CHIPCO_CLK_M2_SHIFT 8
438#define SSB_CHIPCO_CLK_M3 0x003F0000 /* m3 control */
439#define SSB_CHIPCO_CLK_M3_SHIFT 16
440#define SSB_CHIPCO_CLK_MC 0x1F000000 /* mux control */
441#define SSB_CHIPCO_CLK_MC_SHIFT 24
442
443/* N3M Clock control magic field values */
444#define SSB_CHIPCO_CLK_F6_2 0x02 /* A factor of 2 in */
445#define SSB_CHIPCO_CLK_F6_3 0x03 /* 6-bit fields like */
446#define SSB_CHIPCO_CLK_F6_4 0x05 /* N1, M1 or M3 */
447#define SSB_CHIPCO_CLK_F6_5 0x09
448#define SSB_CHIPCO_CLK_F6_6 0x11
449#define SSB_CHIPCO_CLK_F6_7 0x21
450
451#define SSB_CHIPCO_CLK_F5_BIAS 5 /* 5-bit fields get this added */
452
453#define SSB_CHIPCO_CLK_MC_BYPASS 0x08
454#define SSB_CHIPCO_CLK_MC_M1 0x04
455#define SSB_CHIPCO_CLK_MC_M1M2 0x02
456#define SSB_CHIPCO_CLK_MC_M1M2M3 0x01
457#define SSB_CHIPCO_CLK_MC_M1M3 0x11
458
459/* Type 2 Clock control magic field values */
460#define SSB_CHIPCO_CLK_T2_BIAS 2 /* n1, n2, m1 & m3 bias */
461#define SSB_CHIPCO_CLK_T2M2_BIAS 3 /* m2 bias */
462
463#define SSB_CHIPCO_CLK_T2MC_M1BYP 1
464#define SSB_CHIPCO_CLK_T2MC_M2BYP 2
465#define SSB_CHIPCO_CLK_T2MC_M3BYP 4
466
467/* Type 6 Clock control magic field values */
468#define SSB_CHIPCO_CLK_T6_MMASK 1 /* bits of interest in m */
469#define SSB_CHIPCO_CLK_T6_M0 120000000 /* sb clock for m = 0 */
470#define SSB_CHIPCO_CLK_T6_M1 100000000 /* sb clock for m = 1 */
471#define SSB_CHIPCO_CLK_SB2MIPS_T6(sb) (2 * (sb))
472
473/* Common clock base */
474#define SSB_CHIPCO_CLK_BASE1 24000000 /* Half the clock freq */
475#define SSB_CHIPCO_CLK_BASE2 12500000 /* Alternate crystal on some PLL's */
476
477/* Clock control values for 200Mhz in 5350 */
478#define SSB_CHIPCO_CLK_5350_N 0x0311
479#define SSB_CHIPCO_CLK_5350_M 0x04020009
480
481
482/** Bits in the config registers **/
483
484#define SSB_CHIPCO_CFG_EN 0x0001 /* Enable */
485#define SSB_CHIPCO_CFG_EXTM 0x000E /* Extif Mode */
486#define SSB_CHIPCO_CFG_EXTM_ASYNC 0x0002 /* Async/Parallel flash */
487#define SSB_CHIPCO_CFG_EXTM_SYNC 0x0004 /* Synchronous */
488#define SSB_CHIPCO_CFG_EXTM_PCMCIA 0x0008 /* PCMCIA */
489#define SSB_CHIPCO_CFG_EXTM_IDE 0x000A /* IDE */
490#define SSB_CHIPCO_CFG_DS16 0x0010 /* Data size, 0=8bit, 1=16bit */
491#define SSB_CHIPCO_CFG_CLKDIV 0x0060 /* Sync: Clock divisor */
492#define SSB_CHIPCO_CFG_CLKEN 0x0080 /* Sync: Clock enable */
493#define SSB_CHIPCO_CFG_BSTRO 0x0100 /* Sync: Size/Bytestrobe */
494
495
496/** Flash-specific control/status values */
497
498/* flashcontrol opcodes for ST flashes */
499#define SSB_CHIPCO_FLASHCTL_ST_WREN 0x0006 /* Write Enable */
500#define SSB_CHIPCO_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */
501#define SSB_CHIPCO_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */
502#define SSB_CHIPCO_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */
503#define SSB_CHIPCO_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */
504#define SSB_CHIPCO_FLASHCTL_ST_PP 0x0302 /* Page Program */
505#define SSB_CHIPCO_FLASHCTL_ST_SE 0x02D8 /* Sector Erase */
506#define SSB_CHIPCO_FLASHCTL_ST_BE 0x00C7 /* Bulk Erase */
507#define SSB_CHIPCO_FLASHCTL_ST_DP 0x00B9 /* Deep Power-down */
Rafał Miłecki902d9e02012-08-08 19:37:04 +0200508#define SSB_CHIPCO_FLASHCTL_ST_RES 0x03AB /* Read Electronic Signature */
509#define SSB_CHIPCO_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */
510#define SSB_CHIPCO_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */
Michael Buesch61e115a2007-09-18 15:12:50 -0400511
512/* Status register bits for ST flashes */
513#define SSB_CHIPCO_FLASHSTA_ST_WIP 0x01 /* Write In Progress */
514#define SSB_CHIPCO_FLASHSTA_ST_WEL 0x02 /* Write Enable Latch */
515#define SSB_CHIPCO_FLASHSTA_ST_BP 0x1C /* Block Protect */
516#define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT 2
517#define SSB_CHIPCO_FLASHSTA_ST_SRWD 0x80 /* Status Register Write Disable */
518
519/* flashcontrol opcodes for Atmel flashes */
520#define SSB_CHIPCO_FLASHCTL_AT_READ 0x07E8
521#define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ 0x07D2
522#define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ /* FIXME */
523#define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ /* FIXME */
524#define SSB_CHIPCO_FLASHCTL_AT_STATUS 0x01D7
525#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE 0x0384
526#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE 0x0387
527#define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM 0x0283 /* Erase program */
528#define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM 0x0286 /* Erase program */
529#define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM 0x0288
530#define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM 0x0289
531#define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE 0x0281
532#define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE 0x0250
533#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM 0x0382 /* Write erase program */
534#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM 0x0385 /* Write erase program */
535#define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD 0x0253
536#define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD 0x0255
537#define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE 0x0260
538#define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE 0x0261
539#define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM 0x0258
540#define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM 0x0259
541
542/* Status register bits for Atmel flashes */
543#define SSB_CHIPCO_FLASHSTA_AT_READY 0x80
544#define SSB_CHIPCO_FLASHSTA_AT_MISMATCH 0x40
545#define SSB_CHIPCO_FLASHSTA_AT_ID 0x38
546#define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT 3
547
548
549/** OTP **/
550
551/* OTP regions */
552#define SSB_CHIPCO_OTP_HW_REGION SSB_CHIPCO_OTPS_HW_PROTECT
553#define SSB_CHIPCO_OTP_SW_REGION SSB_CHIPCO_OTPS_SW_PROTECT
554#define SSB_CHIPCO_OTP_CID_REGION SSB_CHIPCO_OTPS_CID_PROTECT
555
556/* OTP regions (Byte offsets from otp size) */
557#define SSB_CHIPCO_OTP_SWLIM_OFF (-8)
558#define SSB_CHIPCO_OTP_CIDBASE_OFF 0
559#define SSB_CHIPCO_OTP_CIDLIM_OFF 8
560
561/* Predefined OTP words (Word offset from otp size) */
562#define SSB_CHIPCO_OTP_BOUNDARY_OFF (-4)
563#define SSB_CHIPCO_OTP_HWSIGN_OFF (-3)
564#define SSB_CHIPCO_OTP_SWSIGN_OFF (-2)
565#define SSB_CHIPCO_OTP_CIDSIGN_OFF (-1)
566
567#define SSB_CHIPCO_OTP_CID_OFF 0
568#define SSB_CHIPCO_OTP_PKG_OFF 1
569#define SSB_CHIPCO_OTP_FID_OFF 2
570#define SSB_CHIPCO_OTP_RSV_OFF 3
571#define SSB_CHIPCO_OTP_LIM_OFF 4
572
573#define SSB_CHIPCO_OTP_SIGNATURE 0x578A
574#define SSB_CHIPCO_OTP_MAGIC 0x4E56
575
576
577struct ssb_device;
578struct ssb_serial_port;
579
Michael Bueschc9703142009-02-03 19:23:18 +0100580/* Data for the PMU, if available.
581 * Check availability with ((struct ssb_chipcommon)->capabilities & SSB_CHIPCO_CAP_PMU)
582 */
583struct ssb_chipcommon_pmu {
584 u8 rev; /* PMU revision */
585 u32 crystalfreq; /* The active crystal frequency (in kHz) */
586};
587
Michael Buesch61e115a2007-09-18 15:12:50 -0400588struct ssb_chipcommon {
589 struct ssb_device *dev;
590 u32 capabilities;
John W. Linvilled53cdbb2010-03-31 21:39:35 +0200591 u32 status;
Michael Buesch61e115a2007-09-18 15:12:50 -0400592 /* Fast Powerup Delay constant */
593 u16 fast_pwrup_delay;
Hauke Mehrtens394bc7e2012-11-20 22:24:32 +0000594 spinlock_t gpio_lock;
Michael Bueschc9703142009-02-03 19:23:18 +0100595 struct ssb_chipcommon_pmu pmu;
Hauke Mehrtens7ffbffe2012-12-05 18:46:05 +0100596 u32 ticks_per_ms;
597 u32 max_timer_ms;
Michael Buesch61e115a2007-09-18 15:12:50 -0400598};
599
Michael Buesch42bfad42008-02-19 12:41:30 +0100600static inline bool ssb_chipco_available(struct ssb_chipcommon *cc)
601{
602 return (cc->dev != NULL);
603}
604
Michael Bueschc9703142009-02-03 19:23:18 +0100605/* Register access */
606#define chipco_read32(cc, offset) ssb_read32((cc)->dev, offset)
607#define chipco_write32(cc, offset, val) ssb_write32((cc)->dev, offset, val)
608
609#define chipco_mask32(cc, offset, mask) \
610 chipco_write32(cc, offset, chipco_read32(cc, offset) & (mask))
611#define chipco_set32(cc, offset, set) \
612 chipco_write32(cc, offset, chipco_read32(cc, offset) | (set))
613#define chipco_maskset32(cc, offset, mask, set) \
614 chipco_write32(cc, offset, (chipco_read32(cc, offset) & (mask)) | (set))
615
Michael Buesch61e115a2007-09-18 15:12:50 -0400616extern void ssb_chipcommon_init(struct ssb_chipcommon *cc);
617
Michael Buesch8fe2b652008-03-30 00:10:50 +0100618extern void ssb_chipco_suspend(struct ssb_chipcommon *cc);
Michael Buesch61e115a2007-09-18 15:12:50 -0400619extern void ssb_chipco_resume(struct ssb_chipcommon *cc);
620
621extern void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc,
622 u32 *plltype, u32 *n, u32 *m);
623extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
624 u32 *plltype, u32 *n, u32 *m);
625extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
626 unsigned long ns_per_cycle);
627
628enum ssb_clkmode {
629 SSB_CLKMODE_SLOW,
630 SSB_CLKMODE_FAST,
631 SSB_CLKMODE_DYNAMIC,
632};
633
634extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
635 enum ssb_clkmode mode);
636
Hauke Mehrtens7ffbffe2012-12-05 18:46:05 +0100637extern u32 ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks);
Michael Buesch61e115a2007-09-18 15:12:50 -0400638
Aurelien Jarno28de57d2008-02-22 16:14:58 +0100639void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value);
640
641u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask);
642
Michael Bueschc2bcbe62008-02-19 14:53:35 +0100643/* Chipcommon GPIO pin access. */
Michael Buesch61e115a2007-09-18 15:12:50 -0400644u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask);
Michael Bueschc2bcbe62008-02-19 14:53:35 +0100645u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value);
646u32 ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value);
647u32 ssb_chipco_gpio_control(struct ssb_chipcommon *cc, u32 mask, u32 value);
648u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value);
649u32 ssb_chipco_gpio_polarity(struct ssb_chipcommon *cc, u32 mask, u32 value);
Hauke Mehrtensda22f222012-11-20 22:24:31 +0000650u32 ssb_chipco_gpio_pullup(struct ssb_chipcommon *cc, u32 mask, u32 value);
651u32 ssb_chipco_gpio_pulldown(struct ssb_chipcommon *cc, u32 mask, u32 value);
Michael Buesch61e115a2007-09-18 15:12:50 -0400652
653#ifdef CONFIG_SSB_SERIAL
654extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
655 struct ssb_serial_port *ports);
656#endif /* CONFIG_SSB_SERIAL */
657
Michael Bueschc9703142009-02-03 19:23:18 +0100658/* PMU support */
659extern void ssb_pmu_init(struct ssb_chipcommon *cc);
660
Gábor Stefanik06e4da22009-08-26 20:51:26 +0200661enum ssb_pmu_ldo_volt_id {
662 LDO_PAREF = 0,
663 LDO_VOLT1,
664 LDO_VOLT2,
665 LDO_VOLT3,
666};
667
668void ssb_pmu_set_ldo_voltage(struct ssb_chipcommon *cc,
669 enum ssb_pmu_ldo_volt_id id, u32 voltage);
670void ssb_pmu_set_ldo_paref(struct ssb_chipcommon *cc, bool on);
Rafał Miłecki46fc4c92013-04-02 15:57:26 +0200671void ssb_pmu_spuravoid_pllupdate(struct ssb_chipcommon *cc, int spuravoid);
Michael Bueschc9703142009-02-03 19:23:18 +0100672
Michael Buesch61e115a2007-09-18 15:12:50 -0400673#endif /* LINUX_SSB_CHIPCO_H_ */