blob: acb67a4af2cce0ad5bab6b4262580176bd539fb2 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/**************************************************************************
2 * Initio 9100 device driver for Linux.
3 *
4 * Copyright (c) 1994-1998 Initio Corporation
5 * All rights reserved.
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License as published by
9 * the Free Software Foundation; either version 2, or (at your option)
10 * any later version.
11 *
12 * This program is distributed in the hope that it will be useful,
13 * but WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
15 * GNU General Public License for more details.
16 *
17 * You should have received a copy of the GNU General Public License
18 * along with this program; see the file COPYING. If not, write to
19 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
20 *
21 * --------------------------------------------------------------------------
22 *
23 * Redistribution and use in source and binary forms, with or without
24 * modification, are permitted provided that the following conditions
25 * are met:
26 * 1. Redistributions of source code must retain the above copyright
27 * notice, this list of conditions, and the following disclaimer,
28 * without modification, immediately at the beginning of the file.
29 * 2. Redistributions in binary form must reproduce the above copyright
30 * notice, this list of conditions and the following disclaimer in the
31 * documentation and/or other materials provided with the distribution.
32 * 3. The name of the author may not be used to endorse or promote products
33 * derived from this software without specific prior written permission.
34 *
35 * Where this Software is combined with software released under the terms of
36 * the GNU General Public License ("GPL") and the terms of the GPL would require the
37 * combined work to also be released under the terms of the GPL, the terms
38 * and conditions of this License will apply in addition to those of the
39 * GPL with the exception of any terms or conditions of this License that
40 * conflict with, or are expressly prohibited by, the GPL.
41 *
42 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
43 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
44 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
45 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
46 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
47 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
48 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
49 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
50 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
51 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
52 * SUCH DAMAGE.
53 *
54 **************************************************************************/
55
56
Linus Torvalds1da177e2005-04-16 15:20:36 -070057#include <linux/types.h>
58
59#define ULONG unsigned long
60#define USHORT unsigned short
61#define UCHAR unsigned char
62#define BYTE unsigned char
63#define WORD unsigned short
64#define DWORD unsigned long
65#define UBYTE unsigned char
66#define UWORD unsigned short
67#define UDWORD unsigned long
68#define U32 u32
69
70#define TOTAL_SG_ENTRY 32
71#define MAX_SUPPORTED_ADAPTERS 8
72#define MAX_OFFSET 15
73#define MAX_TARGETS 16
74
75typedef struct {
76 unsigned short base;
77 unsigned short vec;
78} i91u_config;
79
80/***************************************/
81/* Tulip Configuration Register Set */
82/***************************************/
83#define TUL_PVID 0x00 /* Vendor ID */
84#define TUL_PDID 0x02 /* Device ID */
85#define TUL_PCMD 0x04 /* Command */
86#define TUL_PSTUS 0x06 /* Status */
87#define TUL_PRID 0x08 /* Revision number */
88#define TUL_PPI 0x09 /* Programming interface */
89#define TUL_PSC 0x0A /* Sub Class */
90#define TUL_PBC 0x0B /* Base Class */
91#define TUL_PCLS 0x0C /* Cache line size */
92#define TUL_PLTR 0x0D /* Latency timer */
93#define TUL_PHDT 0x0E /* Header type */
94#define TUL_PBIST 0x0F /* BIST */
95#define TUL_PBAD 0x10 /* Base address */
96#define TUL_PBAD1 0x14 /* Base address */
97#define TUL_PBAD2 0x18 /* Base address */
98#define TUL_PBAD3 0x1C /* Base address */
99#define TUL_PBAD4 0x20 /* Base address */
100#define TUL_PBAD5 0x24 /* Base address */
101#define TUL_PRSVD 0x28 /* Reserved */
102#define TUL_PRSVD1 0x2C /* Reserved */
103#define TUL_PRAD 0x30 /* Expansion ROM base address */
104#define TUL_PRSVD2 0x34 /* Reserved */
105#define TUL_PRSVD3 0x38 /* Reserved */
106#define TUL_PINTL 0x3C /* Interrupt line */
107#define TUL_PINTP 0x3D /* Interrupt pin */
108#define TUL_PIGNT 0x3E /* MIN_GNT */
109#define TUL_PMGNT 0x3F /* MAX_GNT */
110
111/************************/
112/* Jasmin Register Set */
113/************************/
114#define TUL_HACFG0 0x40 /* H/A Configuration Register 0 */
115#define TUL_HACFG1 0x41 /* H/A Configuration Register 1 */
116#define TUL_HACFG2 0x42 /* H/A Configuration Register 2 */
117
118#define TUL_SDCFG0 0x44 /* SCSI Device Configuration 0 */
119#define TUL_SDCFG1 0x45 /* SCSI Device Configuration 1 */
120#define TUL_SDCFG2 0x46 /* SCSI Device Configuration 2 */
121#define TUL_SDCFG3 0x47 /* SCSI Device Configuration 3 */
122
123#define TUL_GINTS 0x50 /* Global Interrupt Status Register */
124#define TUL_GIMSK 0x52 /* Global Interrupt MASK Register */
125#define TUL_GCTRL 0x54 /* Global Control Register */
126#define TUL_GCTRL_EEPROM_BIT 0x04
127#define TUL_GCTRL1 0x55 /* Global Control Register */
128#define TUL_DMACFG 0x5B /* DMA configuration */
129#define TUL_NVRAM 0x5D /* Non-volatile RAM port */
130
131#define TUL_SCnt0 0x80 /* 00 R/W Transfer Counter Low */
132#define TUL_SCnt1 0x81 /* 01 R/W Transfer Counter Mid */
133#define TUL_SCnt2 0x82 /* 02 R/W Transfer Count High */
134#define TUL_SFifoCnt 0x83 /* 03 R FIFO counter */
135#define TUL_SIntEnable 0x84 /* 03 W Interrupt enble */
136#define TUL_SInt 0x84 /* 04 R Interrupt Register */
137#define TUL_SCtrl0 0x85 /* 05 W Control 0 */
138#define TUL_SStatus0 0x85 /* 05 R Status 0 */
139#define TUL_SCtrl1 0x86 /* 06 W Control 1 */
140#define TUL_SStatus1 0x86 /* 06 R Status 1 */
141#define TUL_SConfig 0x87 /* 07 W Configuration */
142#define TUL_SStatus2 0x87 /* 07 R Status 2 */
143#define TUL_SPeriod 0x88 /* 08 W Sync. Transfer Period & Offset */
144#define TUL_SOffset 0x88 /* 08 R Offset */
145#define TUL_SScsiId 0x89 /* 09 W SCSI ID */
146#define TUL_SBusId 0x89 /* 09 R SCSI BUS ID */
147#define TUL_STimeOut 0x8A /* 0A W Sel/Resel Time Out Register */
148#define TUL_SIdent 0x8A /* 0A R Identify Message Register */
149#define TUL_SAvail 0x8A /* 0A R Availiable Counter Register */
150#define TUL_SData 0x8B /* 0B R/W SCSI data in/out */
151#define TUL_SFifo 0x8C /* 0C R/W FIFO */
152#define TUL_SSignal 0x90 /* 10 R/W SCSI signal in/out */
153#define TUL_SCmd 0x91 /* 11 R/W Command */
154#define TUL_STest0 0x92 /* 12 R/W Test0 */
155#define TUL_STest1 0x93 /* 13 R/W Test1 */
156#define TUL_SCFG1 0x94 /* 14 R/W Configuration */
157
158#define TUL_XAddH 0xC0 /*DMA Transfer Physical Address */
159#define TUL_XAddW 0xC8 /*DMA Current Transfer Physical Address */
160#define TUL_XCntH 0xD0 /*DMA Transfer Counter */
161#define TUL_XCntW 0xD4 /*DMA Current Transfer Counter */
162#define TUL_XCmd 0xD8 /*DMA Command Register */
163#define TUL_Int 0xDC /*Interrupt Register */
164#define TUL_XStatus 0xDD /*DMA status Register */
165#define TUL_Mask 0xE0 /*Interrupt Mask Register */
166#define TUL_XCtrl 0xE4 /*DMA Control Register */
167#define TUL_XCtrl1 0xE5 /*DMA Control Register 1 */
168#define TUL_XFifo 0xE8 /*DMA FIFO */
169
170#define TUL_WCtrl 0xF7 /*Bus master wait state control */
171#define TUL_DCtrl 0xFB /*DMA delay control */
172
173/*----------------------------------------------------------------------*/
174/* bit definition for Command register of Configuration Space Header */
175/*----------------------------------------------------------------------*/
176#define BUSMS 0x04 /* BUS MASTER Enable */
177#define IOSPA 0x01 /* IO Space Enable */
178
179/*----------------------------------------------------------------------*/
180/* Command Codes of Tulip SCSI Command register */
181/*----------------------------------------------------------------------*/
182#define TSC_EN_RESEL 0x80 /* Enable Reselection */
183#define TSC_CMD_COMP 0x84 /* Command Complete Sequence */
184#define TSC_SEL 0x01 /* Select Without ATN Sequence */
185#define TSC_SEL_ATN 0x11 /* Select With ATN Sequence */
186#define TSC_SEL_ATN_DMA 0x51 /* Select With ATN Sequence with DMA */
187#define TSC_SEL_ATN3 0x31 /* Select With ATN3 Sequence */
188#define TSC_SEL_ATNSTOP 0x12 /* Select With ATN and Stop Sequence */
189#define TSC_SELATNSTOP 0x1E /* Select With ATN and Stop Sequence */
190
191#define TSC_SEL_ATN_DIRECT_IN 0x95 /* Select With ATN Sequence */
192#define TSC_SEL_ATN_DIRECT_OUT 0x15 /* Select With ATN Sequence */
193#define TSC_SEL_ATN3_DIRECT_IN 0xB5 /* Select With ATN3 Sequence */
194#define TSC_SEL_ATN3_DIRECT_OUT 0x35 /* Select With ATN3 Sequence */
Adrian Bunk47bdd712006-06-30 18:25:18 +0200195#define TSC_XF_DMA_OUT_DIRECT 0x06 /* DMA Xfer Information out */
196#define TSC_XF_DMA_IN_DIRECT 0x86 /* DMA Xfer Information in */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700197
Adrian Bunk47bdd712006-06-30 18:25:18 +0200198#define TSC_XF_DMA_OUT 0x43 /* DMA Xfer Information out */
199#define TSC_XF_DMA_IN 0xC3 /* DMA Xfer Information in */
200#define TSC_XF_FIFO_OUT 0x03 /* FIFO Xfer Information out */
201#define TSC_XF_FIFO_IN 0x83 /* FIFO Xfer Information in */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700202
203#define TSC_MSG_ACCEPT 0x0F /* Message Accept */
204
205/*----------------------------------------------------------------------*/
206/* bit definition for Tulip SCSI Control 0 Register */
207/*----------------------------------------------------------------------*/
208#define TSC_RST_SEQ 0x20 /* Reset sequence counter */
209#define TSC_FLUSH_FIFO 0x10 /* Flush FIFO */
210#define TSC_ABT_CMD 0x04 /* Abort command (sequence) */
211#define TSC_RST_CHIP 0x02 /* Reset SCSI Chip */
212#define TSC_RST_BUS 0x01 /* Reset SCSI Bus */
213
214/*----------------------------------------------------------------------*/
215/* bit definition for Tulip SCSI Control 1 Register */
216/*----------------------------------------------------------------------*/
217#define TSC_EN_SCAM 0x80 /* Enable SCAM */
218#define TSC_TIMER 0x40 /* Select timeout unit */
219#define TSC_EN_SCSI2 0x20 /* SCSI-2 mode */
220#define TSC_PWDN 0x10 /* Power down mode */
221#define TSC_WIDE_CPU 0x08 /* Wide CPU */
222#define TSC_HW_RESELECT 0x04 /* Enable HW reselect */
223#define TSC_EN_BUS_OUT 0x02 /* Enable SCSI data bus out latch */
224#define TSC_EN_BUS_IN 0x01 /* Enable SCSI data bus in latch */
225
226/*----------------------------------------------------------------------*/
227/* bit definition for Tulip SCSI Configuration Register */
228/*----------------------------------------------------------------------*/
229#define TSC_EN_LATCH 0x80 /* Enable phase latch */
230#define TSC_INITIATOR 0x40 /* Initiator mode */
231#define TSC_EN_SCSI_PAR 0x20 /* Enable SCSI parity */
232#define TSC_DMA_8BIT 0x10 /* Alternate dma 8-bits mode */
233#define TSC_DMA_16BIT 0x08 /* Alternate dma 16-bits mode */
234#define TSC_EN_WDACK 0x04 /* Enable DACK while wide SCSI xfer */
235#define TSC_ALT_PERIOD 0x02 /* Alternate sync period mode */
236#define TSC_DIS_SCSIRST 0x01 /* Disable SCSI bus reset us */
237
238#define TSC_INITDEFAULT (TSC_INITIATOR | TSC_EN_LATCH | TSC_ALT_PERIOD | TSC_DIS_SCSIRST)
239
240#define TSC_WIDE_SCSI 0x80 /* Enable Wide SCSI */
241
242/*----------------------------------------------------------------------*/
243/* bit definition for Tulip SCSI signal Register */
244/*----------------------------------------------------------------------*/
245#define TSC_RST_ACK 0x00 /* Release ACK signal */
246#define TSC_RST_ATN 0x00 /* Release ATN signal */
247#define TSC_RST_BSY 0x00 /* Release BSY signal */
248
249#define TSC_SET_ACK 0x40 /* ACK signal */
250#define TSC_SET_ATN 0x08 /* ATN signal */
251
252#define TSC_REQI 0x80 /* REQ signal */
253#define TSC_ACKI 0x40 /* ACK signal */
254#define TSC_BSYI 0x20 /* BSY signal */
255#define TSC_SELI 0x10 /* SEL signal */
256#define TSC_ATNI 0x08 /* ATN signal */
257#define TSC_MSGI 0x04 /* MSG signal */
258#define TSC_CDI 0x02 /* C/D signal */
259#define TSC_IOI 0x01 /* I/O signal */
260
261
262/*----------------------------------------------------------------------*/
263/* bit definition for Tulip SCSI Status 0 Register */
264/*----------------------------------------------------------------------*/
265#define TSS_INT_PENDING 0x80 /* Interrupt pending */
266#define TSS_SEQ_ACTIVE 0x40 /* Sequencer active */
267#define TSS_XFER_CNT 0x20 /* Transfer counter zero */
268#define TSS_FIFO_EMPTY 0x10 /* FIFO empty */
269#define TSS_PAR_ERROR 0x08 /* SCSI parity error */
270#define TSS_PH_MASK 0x07 /* SCSI phase mask */
271
272/*----------------------------------------------------------------------*/
273/* bit definition for Tulip SCSI Status 1 Register */
274/*----------------------------------------------------------------------*/
275#define TSS_STATUS_RCV 0x08 /* Status received */
276#define TSS_MSG_SEND 0x40 /* Message sent */
277#define TSS_CMD_PH_CMP 0x20 /* command phase done */
278#define TSS_DATA_PH_CMP 0x10 /* Data phase done */
279#define TSS_STATUS_SEND 0x08 /* Status sent */
280#define TSS_XFER_CMP 0x04 /* Transfer completed */
281#define TSS_SEL_CMP 0x02 /* Selection completed */
282#define TSS_ARB_CMP 0x01 /* Arbitration completed */
283
284/*----------------------------------------------------------------------*/
285/* bit definition for Tulip SCSI Status 2 Register */
286/*----------------------------------------------------------------------*/
287#define TSS_CMD_ABTED 0x80 /* Command aborted */
288#define TSS_OFFSET_0 0x40 /* Offset counter zero */
289#define TSS_FIFO_FULL 0x20 /* FIFO full */
290#define TSS_TIMEOUT_0 0x10 /* Timeout counter zero */
291#define TSS_BUSY_RLS 0x08 /* Busy release */
292#define TSS_PH_MISMATCH 0x04 /* Phase mismatch */
293#define TSS_SCSI_BUS_EN 0x02 /* SCSI data bus enable */
294#define TSS_SCSIRST 0x01 /* SCSI bus reset in progress */
295
296/*----------------------------------------------------------------------*/
297/* bit definition for Tulip SCSI Interrupt Register */
298/*----------------------------------------------------------------------*/
299#define TSS_RESEL_INT 0x80 /* Reselected interrupt */
300#define TSS_SEL_TIMEOUT 0x40 /* Selected/reselected timeout */
301#define TSS_BUS_SERV 0x20
302#define TSS_SCSIRST_INT 0x10 /* SCSI bus reset detected */
303#define TSS_DISC_INT 0x08 /* Disconnected interrupt */
304#define TSS_SEL_INT 0x04 /* Select interrupt */
305#define TSS_SCAM_SEL 0x02 /* SCAM selected */
306#define TSS_FUNC_COMP 0x01
307
308/*----------------------------------------------------------------------*/
309/* SCSI Phase Codes. */
310/*----------------------------------------------------------------------*/
311#define DATA_OUT 0
312#define DATA_IN 1 /* 4 */
313#define CMD_OUT 2
314#define STATUS_IN 3 /* 6 */
315#define MSG_OUT 6 /* 3 */
316#define MSG_IN 7
317
318
319
320/*----------------------------------------------------------------------*/
321/* Command Codes of Tulip xfer Command register */
322/*----------------------------------------------------------------------*/
323#define TAX_X_FORC 0x02
324#define TAX_X_ABT 0x04
325#define TAX_X_CLR_FIFO 0x08
326
327#define TAX_X_IN 0x21
328#define TAX_X_OUT 0x01
329#define TAX_SG_IN 0xA1
330#define TAX_SG_OUT 0x81
331
332/*----------------------------------------------------------------------*/
333/* Tulip Interrupt Register */
334/*----------------------------------------------------------------------*/
335#define XCMP 0x01
336#define FCMP 0x02
337#define XABT 0x04
338#define XERR 0x08
339#define SCMP 0x10
340#define IPEND 0x80
341
342/*----------------------------------------------------------------------*/
343/* Tulip DMA Status Register */
344/*----------------------------------------------------------------------*/
345#define XPEND 0x01 /* Transfer pending */
346#define FEMPTY 0x02 /* FIFO empty */
347
348
349
350/*----------------------------------------------------------------------*/
351/* bit definition for TUL_GCTRL */
352/*----------------------------------------------------------------------*/
353#define EXTSG 0x80
354#define EXTAD 0x60
355#define SEG4K 0x08
356#define EEPRG 0x04
357#define MRMUL 0x02
358
359/*----------------------------------------------------------------------*/
360/* bit definition for TUL_NVRAM */
361/*----------------------------------------------------------------------*/
362#define SE2CS 0x08
363#define SE2CLK 0x04
364#define SE2DO 0x02
365#define SE2DI 0x01
366
367
368/************************************************************************/
369/* Scatter-Gather Element Structure */
370/************************************************************************/
371typedef struct SG_Struc {
372 U32 SG_Ptr; /* Data Pointer */
373 U32 SG_Len; /* Data Length */
374} SG;
375
376/***********************************************************************
377 SCSI Control Block
378************************************************************************/
379typedef struct Scsi_Ctrl_Blk {
380 struct Scsi_Ctrl_Blk *SCB_NxtScb;
381 UBYTE SCB_Status; /*4 */
382 UBYTE SCB_NxtStat; /*5 */
383 UBYTE SCB_Mode; /*6 */
384 UBYTE SCB_Msgin; /*7 SCB_Res0 */
385 UWORD SCB_SGIdx; /*8 */
386 UWORD SCB_SGMax; /*A */
387#ifdef ALPHA
388 U32 SCB_Reserved[2]; /*C */
389#else
390 U32 SCB_Reserved[3]; /*C */
391#endif
392
393 U32 SCB_XferLen; /*18 Current xfer len */
394 U32 SCB_TotXLen; /*1C Total xfer len */
395 U32 SCB_PAddr; /*20 SCB phy. Addr. */
396
397 UBYTE SCB_Opcode; /*24 SCB command code */
398 UBYTE SCB_Flags; /*25 SCB Flags */
399 UBYTE SCB_Target; /*26 Target Id */
400 UBYTE SCB_Lun; /*27 Lun */
401 U32 SCB_BufPtr; /*28 Data Buffer Pointer */
402 U32 SCB_BufLen; /*2C Data Allocation Length */
403 UBYTE SCB_SGLen; /*30 SG list # */
404 UBYTE SCB_SenseLen; /*31 Sense Allocation Length */
405 UBYTE SCB_HaStat; /*32 */
406 UBYTE SCB_TaStat; /*33 */
407 UBYTE SCB_CDBLen; /*34 CDB Length */
408 UBYTE SCB_Ident; /*35 Identify */
409 UBYTE SCB_TagMsg; /*36 Tag Message */
410 UBYTE SCB_TagId; /*37 Queue Tag */
411 UBYTE SCB_CDB[12]; /*38 */
412 U32 SCB_SGPAddr; /*44 SG List/Sense Buf phy. Addr. */
413 U32 SCB_SensePtr; /*48 Sense data pointer */
414 void (*SCB_Post) (BYTE *, BYTE *); /*4C POST routine */
415 struct scsi_cmnd *SCB_Srb; /*50 SRB Pointer */
416 SG SCB_SGList[TOTAL_SG_ENTRY]; /*54 Start of SG list */
417} SCB;
418
419/* Bit Definition for SCB_Status */
420#define SCB_RENT 0x01
421#define SCB_PEND 0x02
422#define SCB_CONTIG 0x04 /* Contigent Allegiance */
423#define SCB_SELECT 0x08
424#define SCB_BUSY 0x10
425#define SCB_DONE 0x20
426
427
428/* Opcodes of SCB_Opcode */
429#define ExecSCSI 0x1
430#define BusDevRst 0x2
431#define AbortCmd 0x3
432
433
434/* Bit Definition for SCB_Mode */
435#define SCM_RSENS 0x01 /* request sense mode */
436
437
438/* Bit Definition for SCB_Flags */
439#define SCF_DONE 0x01
440#define SCF_POST 0x02
441#define SCF_SENSE 0x04
442#define SCF_DIR 0x18
443#define SCF_NO_DCHK 0x00
444#define SCF_DIN 0x08
445#define SCF_DOUT 0x10
446#define SCF_NO_XF 0x18
447#define SCF_WR_VF 0x20 /* Write verify turn on */
448#define SCF_POLL 0x40
449#define SCF_SG 0x80
450
451/* Error Codes for SCB_HaStat */
452#define HOST_SEL_TOUT 0x11
453#define HOST_DO_DU 0x12
454#define HOST_BUS_FREE 0x13
455#define HOST_BAD_PHAS 0x14
456#define HOST_INV_CMD 0x16
457#define HOST_ABORTED 0x1A /* 07/21/98 */
458#define HOST_SCSI_RST 0x1B
459#define HOST_DEV_RST 0x1C
460
461/* Error Codes for SCB_TaStat */
462#define TARGET_CHKCOND 0x02
463#define TARGET_BUSY 0x08
464#define INI_QUEUE_FULL 0x28
465
466/* SCSI MESSAGE */
467#define MSG_COMP 0x00
468#define MSG_EXTEND 0x01
469#define MSG_SDP 0x02
470#define MSG_RESTORE 0x03
471#define MSG_DISC 0x04
472#define MSG_IDE 0x05
473#define MSG_ABORT 0x06
474#define MSG_REJ 0x07
475#define MSG_NOP 0x08
476#define MSG_PARITY 0x09
477#define MSG_LINK_COMP 0x0A
478#define MSG_LINK_FLAG 0x0B
479#define MSG_DEVRST 0x0C
480#define MSG_ABORT_TAG 0x0D
481
482/* Queue tag msg: Simple_quque_tag, Head_of_queue_tag, Ordered_queue_tag */
483#define MSG_STAG 0x20
484#define MSG_HTAG 0x21
485#define MSG_OTAG 0x22
486
487#define MSG_IGNOREWIDE 0x23
488
489#define MSG_IDENT 0x80
490
491/***********************************************************************
492 Target Device Control Structure
493**********************************************************************/
494
495typedef struct Tar_Ctrl_Struc {
496 UWORD TCS_Flags; /* 0 */
497 UBYTE TCS_JS_Period; /* 2 */
498 UBYTE TCS_SConfig0; /* 3 */
499
500 UWORD TCS_DrvFlags; /* 4 */
501 UBYTE TCS_DrvHead; /* 6 */
502 UBYTE TCS_DrvSector; /* 7 */
503} TCS;
504
505/***********************************************************************
506 Target Device Control Structure
507**********************************************************************/
508
509/* Bit Definition for TCF_Flags */
510#define TCF_SCSI_RATE 0x0007
511#define TCF_EN_DISC 0x0008
512#define TCF_NO_SYNC_NEGO 0x0010
513#define TCF_NO_WDTR 0x0020
514#define TCF_EN_255 0x0040
515#define TCF_EN_START 0x0080
516#define TCF_WDTR_DONE 0x0100
517#define TCF_SYNC_DONE 0x0200
518#define TCF_BUSY 0x0400
519
520
521/* Bit Definition for TCF_DrvFlags */
522#define TCF_DRV_BUSY 0x01 /* Indicate target busy(driver) */
523#define TCF_DRV_EN_TAG 0x0800
524#define TCF_DRV_255_63 0x0400
525
526typedef struct I91u_Adpt_Struc {
527 UWORD ADPT_BIOS; /* 0 */
528 UWORD ADPT_BASE; /* 1 */
529 UBYTE ADPT_Bus; /* 2 */
530 UBYTE ADPT_Device; /* 3 */
531 UBYTE ADPT_INTR; /* 4 */
532} INI_ADPT_STRUCT;
533
534
535/***********************************************************************
536 Host Adapter Control Structure
537************************************************************************/
538typedef struct Ha_Ctrl_Struc {
539 UWORD HCS_Base; /* 00 */
540 UWORD HCS_BIOS; /* 02 */
541 UBYTE HCS_Intr; /* 04 */
542 UBYTE HCS_SCSI_ID; /* 05 */
543 UBYTE HCS_MaxTar; /* 06 */
544 UBYTE HCS_NumScbs; /* 07 */
545
546 UBYTE HCS_Flags; /* 08 */
547 UBYTE HCS_Index; /* 09 */
548 UBYTE HCS_HaId; /* 0A */
549 UBYTE HCS_Config; /* 0B */
550 UWORD HCS_IdMask; /* 0C */
551 UBYTE HCS_Semaph; /* 0E */
552 UBYTE HCS_Phase; /* 0F */
553 UBYTE HCS_JSStatus0; /* 10 */
554 UBYTE HCS_JSInt; /* 11 */
555 UBYTE HCS_JSStatus1; /* 12 */
556 UBYTE HCS_SConf1; /* 13 */
557
558 UBYTE HCS_Msg[8]; /* 14 */
559 SCB *HCS_NxtAvail; /* 1C */
560 SCB *HCS_Scb; /* 20 */
561 SCB *HCS_ScbEnd; /* 24 */
562 SCB *HCS_NxtPend; /* 28 */
563 SCB *HCS_NxtContig; /* 2C */
564 SCB *HCS_ActScb; /* 30 */
565 TCS *HCS_ActTcs; /* 34 */
566
567 SCB *HCS_FirstAvail; /* 38 */
568 SCB *HCS_LastAvail; /* 3C */
569 SCB *HCS_FirstPend; /* 40 */
570 SCB *HCS_LastPend; /* 44 */
571 SCB *HCS_FirstBusy; /* 48 */
572 SCB *HCS_LastBusy; /* 4C */
573 SCB *HCS_FirstDone; /* 50 */
574 SCB *HCS_LastDone; /* 54 */
575 UBYTE HCS_MaxTags[16]; /* 58 */
576 UBYTE HCS_ActTags[16]; /* 68 */
577 TCS HCS_Tcs[MAX_TARGETS]; /* 78 */
578 spinlock_t HCS_AvailLock;
579 spinlock_t HCS_SemaphLock;
580 struct pci_dev *pci_dev;
581} HCS;
582
583/* Bit Definition for HCB_Config */
584#define HCC_SCSI_RESET 0x01
585#define HCC_EN_PAR 0x02
586#define HCC_ACT_TERM1 0x04
587#define HCC_ACT_TERM2 0x08
588#define HCC_AUTO_TERM 0x10
589#define HCC_EN_PWR 0x80
590
591/* Bit Definition for HCB_Flags */
592#define HCF_EXPECT_DISC 0x01
593#define HCF_EXPECT_SELECT 0x02
594#define HCF_EXPECT_RESET 0x10
595#define HCF_EXPECT_DONE_DISC 0x20
596
597/******************************************************************
598 Serial EEProm
599*******************************************************************/
600
601typedef struct _NVRAM_SCSI { /* SCSI channel configuration */
602 UCHAR NVM_ChSCSIID; /* 0Ch -> Channel SCSI ID */
603 UCHAR NVM_ChConfig1; /* 0Dh -> Channel config 1 */
604 UCHAR NVM_ChConfig2; /* 0Eh -> Channel config 2 */
605 UCHAR NVM_NumOfTarg; /* 0Fh -> Number of SCSI target */
606 /* SCSI target configuration */
607 UCHAR NVM_Targ0Config; /* 10h -> Target 0 configuration */
608 UCHAR NVM_Targ1Config; /* 11h -> Target 1 configuration */
609 UCHAR NVM_Targ2Config; /* 12h -> Target 2 configuration */
610 UCHAR NVM_Targ3Config; /* 13h -> Target 3 configuration */
611 UCHAR NVM_Targ4Config; /* 14h -> Target 4 configuration */
612 UCHAR NVM_Targ5Config; /* 15h -> Target 5 configuration */
613 UCHAR NVM_Targ6Config; /* 16h -> Target 6 configuration */
614 UCHAR NVM_Targ7Config; /* 17h -> Target 7 configuration */
615 UCHAR NVM_Targ8Config; /* 18h -> Target 8 configuration */
616 UCHAR NVM_Targ9Config; /* 19h -> Target 9 configuration */
617 UCHAR NVM_TargAConfig; /* 1Ah -> Target A configuration */
618 UCHAR NVM_TargBConfig; /* 1Bh -> Target B configuration */
619 UCHAR NVM_TargCConfig; /* 1Ch -> Target C configuration */
620 UCHAR NVM_TargDConfig; /* 1Dh -> Target D configuration */
621 UCHAR NVM_TargEConfig; /* 1Eh -> Target E configuration */
622 UCHAR NVM_TargFConfig; /* 1Fh -> Target F configuration */
623} NVRAM_SCSI;
624
625typedef struct _NVRAM {
626/*----------header ---------------*/
627 USHORT NVM_Signature; /* 0,1: Signature */
628 UCHAR NVM_Size; /* 2: Size of data structure */
629 UCHAR NVM_Revision; /* 3: Revision of data structure */
630 /* ----Host Adapter Structure ---- */
631 UCHAR NVM_ModelByte0; /* 4: Model number (byte 0) */
632 UCHAR NVM_ModelByte1; /* 5: Model number (byte 1) */
633 UCHAR NVM_ModelInfo; /* 6: Model information */
634 UCHAR NVM_NumOfCh; /* 7: Number of SCSI channel */
635 UCHAR NVM_BIOSConfig1; /* 8: BIOS configuration 1 */
636 UCHAR NVM_BIOSConfig2; /* 9: BIOS configuration 2 */
637 UCHAR NVM_HAConfig1; /* A: Hoat adapter configuration 1 */
638 UCHAR NVM_HAConfig2; /* B: Hoat adapter configuration 2 */
639 NVRAM_SCSI NVM_SCSIInfo[2];
640 UCHAR NVM_reserved[10];
641 /* ---------- CheckSum ---------- */
642 USHORT NVM_CheckSum; /* 0x3E, 0x3F: Checksum of NVRam */
643} NVRAM, *PNVRAM;
644
645/* Bios Configuration for nvram->BIOSConfig1 */
646#define NBC1_ENABLE 0x01 /* BIOS enable */
647#define NBC1_8DRIVE 0x02 /* Support more than 2 drives */
648#define NBC1_REMOVABLE 0x04 /* Support removable drive */
649#define NBC1_INT19 0x08 /* Intercept int 19h */
650#define NBC1_BIOSSCAN 0x10 /* Dynamic BIOS scan */
651#define NBC1_LUNSUPPORT 0x40 /* Support LUN */
652
653/* HA Configuration Byte 1 */
654#define NHC1_BOOTIDMASK 0x0F /* Boot ID number */
655#define NHC1_LUNMASK 0x70 /* Boot LUN number */
656#define NHC1_CHANMASK 0x80 /* Boot Channel number */
657
658/* Bit definition for nvram->SCSIconfig1 */
659#define NCC1_BUSRESET 0x01 /* Reset SCSI bus at power up */
660#define NCC1_PARITYCHK 0x02 /* SCSI parity enable */
661#define NCC1_ACTTERM1 0x04 /* Enable active terminator 1 */
662#define NCC1_ACTTERM2 0x08 /* Enable active terminator 2 */
663#define NCC1_AUTOTERM 0x10 /* Enable auto terminator */
664#define NCC1_PWRMGR 0x80 /* Enable power management */
665
666/* Bit definition for SCSI Target configuration byte */
667#define NTC_DISCONNECT 0x08 /* Enable SCSI disconnect */
668#define NTC_SYNC 0x10 /* SYNC_NEGO */
669#define NTC_NO_WDTR 0x20 /* SYNC_NEGO */
670#define NTC_1GIGA 0x40 /* 255 head / 63 sectors (64/32) */
671#define NTC_SPINUP 0x80 /* Start disk drive */
672
673/* Default NVRam values */
674#define INI_SIGNATURE 0xC925
675#define NBC1_DEFAULT (NBC1_ENABLE)
676#define NCC1_DEFAULT (NCC1_BUSRESET | NCC1_AUTOTERM | NCC1_PARITYCHK)
677#define NTC_DEFAULT (NTC_NO_WDTR | NTC_1GIGA | NTC_DISCONNECT)
678
679/* SCSI related definition */
680#define DISC_NOT_ALLOW 0x80 /* Disconnect is not allowed */
681#define DISC_ALLOW 0xC0 /* Disconnect is allowed */
682#define SCSICMD_RequestSense 0x03
683
684typedef struct _HCSinfo {
685 ULONG base;
686 UCHAR vec;
687 UCHAR bios; /* High byte of BIOS address */
688 USHORT BaseAndBios; /* high byte: pHcsInfo->bios,low byte:pHcsInfo->base */
689} HCSINFO;
690
691#define TUL_RD(x,y) (UCHAR)(inb( (int)((ULONG)(x+y)) ))
692#define TUL_RDLONG(x,y) (ULONG)(inl((int)((ULONG)(x+y)) ))
693#define TUL_WR( adr,data) outb( (UCHAR)(data), (int)(adr))
694#define TUL_WRSHORT(adr,data) outw( (UWORD)(data), (int)(adr))
695#define TUL_WRLONG( adr,data) outl( (ULONG)(data), (int)(adr))
696
697#define SCSI_ABORT_SNOOZE 0
698#define SCSI_ABORT_SUCCESS 1
699#define SCSI_ABORT_PENDING 2
700#define SCSI_ABORT_BUSY 3
701#define SCSI_ABORT_NOT_RUNNING 4
702#define SCSI_ABORT_ERROR 5
703
704#define SCSI_RESET_SNOOZE 0
705#define SCSI_RESET_PUNT 1
706#define SCSI_RESET_SUCCESS 2
707#define SCSI_RESET_PENDING 3
708#define SCSI_RESET_WAKEUP 4
709#define SCSI_RESET_NOT_RUNNING 5
710#define SCSI_RESET_ERROR 6
711
712#define SCSI_RESET_SYNCHRONOUS 0x01
713#define SCSI_RESET_ASYNCHRONOUS 0x02
714#define SCSI_RESET_SUGGEST_BUS_RESET 0x04
715#define SCSI_RESET_SUGGEST_HOST_RESET 0x08
716
717#define SCSI_RESET_BUS_RESET 0x100
718#define SCSI_RESET_HOST_RESET 0x200
719#define SCSI_RESET_ACTION 0xff
720