blob: 097e270955d0d2abce616dc81c07a1a7cf88668b [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* ------------------------------------------------------------------------- */
2/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */
3/* ------------------------------------------------------------------------- */
4/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
5 * <Peter dot Milne at D hyphen TACQ dot com>
6
7 This program is free software; you can redistribute it and/or modify
8 it under the terms of the GNU General Public License as published by
9 the Free Software Foundation, version 2.
10
11 This program is distributed in the hope that it will be useful,
12 but WITHOUT ANY WARRANTY; without even the implied warranty of
13 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 GNU General Public License for more details.
15
16 You should have received a copy of the GNU General Public License
17 along with this program; if not, write to the Free Software
18 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
19/* ------------------------------------------------------------------------- */
20
21
22#ifndef I2C_IOP3XX_H
23#define I2C_IOP3XX_H 1
24
25/*
26 * iop321 hardware bit definitions
27 */
28#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */
29#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */
30#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */
31#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */
32#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */
33#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */
34#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */
35#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */
36#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */
37/*
38 * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
39 * when sending a master mode general call message from the I2C unit"
40 */
41#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */
42/*
43 * "NOTE: To avoid I2C bus integrity problems,
44 * the user needs to ensure that the GPIO Output Data Register -
45 * GPOD bits associated with an I2C port are cleared prior to setting
46 * the enable bit for that I2C serial port.
47 * The user prepares to enable I2C port 0 and
48 * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
49 */
50#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */
51#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data
52 * NB TBYTE must be clear */
53#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */
54#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */
55#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */
56#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */
57
58
59#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */
60#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */
61#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */
62#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */
63#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */
64#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */
65#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */
66#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */
67#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */
68#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */
69#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */
70
71#define IOP3XX_ISR_CLEARBITS 0x07f0
72
73#define IOP3XX_ISAR_SAMASK 0x007f
74
75#define IOP3XX_IDBR_MASK 0x00ff
76
77#define IOP3XX_IBMR_SCL 0x0002
78#define IOP3XX_IBMR_SDA 0x0001
79
80#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
81#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
82
Peter Milne39288e12006-07-01 17:03:20 +020083#define MYSAR 0 /* default slave address */
Linus Torvalds1da177e2005-04-16 15:20:36 -070084
85#define I2C_ERR 321
86#define I2C_ERR_BERR (I2C_ERR+0)
87#define I2C_ERR_ALD (I2C_ERR+1)
88
89
90#define CR_OFFSET 0
91#define SR_OFFSET 0x4
92#define SAR_OFFSET 0x8
93#define DBR_OFFSET 0xc
94#define CCR_OFFSET 0x10
95#define BMR_OFFSET 0x14
96
97#define IOP3XX_I2C_IO_SIZE 0x18
98
99struct i2c_algo_iop3xx_data {
Aaro Koskinen747fcc92010-11-29 12:33:39 +0200100 void __iomem *ioaddr;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700101 wait_queue_head_t waitq;
102 spinlock_t lock;
103 u32 SR_enabled, SR_received;
104 int id;
105};
106
107#endif /* I2C_IOP3XX_H */