blob: d9d0a3a3c558b349e7c3d0a6147bb8a06538a743 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* seeq8005.c: A network driver for linux. */
2/*
3 Based on skeleton.c,
4 Written 1993-94 by Donald Becker.
5 See the skeleton.c file for further copyright information.
6
7 This software may be used and distributed according to the terms
8 of the GNU General Public License, incorporated herein by reference.
9
10 The author may be reached as hamish@zot.apana.org.au
11
12 This file is a network device driver for the SEEQ 8005 chipset and
13 the Linux operating system.
14
15*/
16
17static const char version[] =
18 "seeq8005.c:v1.00 8/07/95 Hamish Coleman (hamish@zot.apana.org.au)\n";
19
20/*
21 Sources:
22 SEEQ 8005 databook
Jeff Garzik6aa20a22006-09-13 13:24:59 -040023
Linus Torvalds1da177e2005-04-16 15:20:36 -070024 Version history:
25 1.00 Public release. cosmetic changes (no warnings now)
26 0.68 Turning per- packet,interrupt debug messages off - testing for release.
27 0.67 timing problems/bad buffer reads seem to be fixed now
28 0.63 *!@$ protocol=eth_type_trans -- now packets flow
29 0.56 Send working
30 0.48 Receive working
31*/
32
33#include <linux/module.h>
34#include <linux/kernel.h>
35#include <linux/types.h>
36#include <linux/fcntl.h>
37#include <linux/interrupt.h>
38#include <linux/ioport.h>
39#include <linux/in.h>
40#include <linux/slab.h>
41#include <linux/string.h>
42#include <linux/init.h>
43#include <linux/delay.h>
44#include <linux/errno.h>
45#include <linux/netdevice.h>
46#include <linux/etherdevice.h>
47#include <linux/skbuff.h>
48#include <linux/bitops.h>
Marcelo Feitoza Parisiff5688a2006-01-09 18:37:15 -080049#include <linux/jiffies.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070050
51#include <asm/system.h>
52#include <asm/io.h>
53#include <asm/dma.h>
54
55#include "seeq8005.h"
56
57/* First, a few definitions that the brave might change. */
58/* A zero-terminated list of I/O addresses to be probed. */
59static unsigned int seeq8005_portlist[] __initdata =
60 { 0x300, 0x320, 0x340, 0x360, 0};
61
62/* use 0 for production, 1 for verification, >2 for debug */
63#ifndef NET_DEBUG
64#define NET_DEBUG 1
65#endif
66static unsigned int net_debug = NET_DEBUG;
67
68/* Information that need to be kept for each board. */
69struct net_local {
70 struct net_device_stats stats;
71 unsigned short receive_ptr; /* What address in packet memory do we expect a recv_pkt_header? */
72 long open_time; /* Useless example local info. */
73};
74
75/* The station (ethernet) address prefix, used for IDing the board. */
76#define SA_ADDR0 0x00
77#define SA_ADDR1 0x80
78#define SA_ADDR2 0x4b
79
80/* Index to functions, as function prototypes. */
81
82static int seeq8005_probe1(struct net_device *dev, int ioaddr);
83static int seeq8005_open(struct net_device *dev);
84static void seeq8005_timeout(struct net_device *dev);
85static int seeq8005_send_packet(struct sk_buff *skb, struct net_device *dev);
David Howells7d12e782006-10-05 14:55:46 +010086static irqreturn_t seeq8005_interrupt(int irq, void *dev_id);
Linus Torvalds1da177e2005-04-16 15:20:36 -070087static void seeq8005_rx(struct net_device *dev);
88static int seeq8005_close(struct net_device *dev);
89static struct net_device_stats *seeq8005_get_stats(struct net_device *dev);
90static void set_multicast_list(struct net_device *dev);
91
92/* Example routines you must write ;->. */
93#define tx_done(dev) (inw(SEEQ_STATUS) & SEEQSTAT_TX_ON)
94static void hardware_send_packet(struct net_device *dev, char *buf, int length);
95extern void seeq8005_init(struct net_device *dev, int startp);
96static inline void wait_for_buffer(struct net_device *dev);
97
Jeff Garzik6aa20a22006-09-13 13:24:59 -040098
Linus Torvalds1da177e2005-04-16 15:20:36 -070099/* Check for a network adaptor of this type, and return '0' iff one exists.
100 If dev->base_addr == 0, probe all likely locations.
101 If dev->base_addr == 1, always return failure.
102 */
103
104static int io = 0x320;
105static int irq = 10;
106
107struct net_device * __init seeq8005_probe(int unit)
108{
109 struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
110 unsigned *port;
111 int err = 0;
112
113 if (!dev)
114 return ERR_PTR(-ENODEV);
115
116 if (unit >= 0) {
117 sprintf(dev->name, "eth%d", unit);
118 netdev_boot_setup_check(dev);
119 io = dev->base_addr;
120 irq = dev->irq;
121 }
122
123 if (io > 0x1ff) { /* Check a single specified location. */
124 err = seeq8005_probe1(dev, io);
125 } else if (io != 0) { /* Don't probe at all. */
126 err = -ENXIO;
127 } else {
128 for (port = seeq8005_portlist; *port; port++) {
129 if (seeq8005_probe1(dev, *port) == 0)
130 break;
131 }
132 if (!*port)
133 err = -ENODEV;
134 }
135 if (err)
136 goto out;
137 err = register_netdev(dev);
138 if (err)
139 goto out1;
140 return dev;
141out1:
142 release_region(dev->base_addr, SEEQ8005_IO_EXTENT);
143out:
144 free_netdev(dev);
145 return ERR_PTR(err);
146}
147
148/* This is the real probe routine. Linux has a history of friendly device
149 probes on the ISA bus. A good device probes avoids doing writes, and
150 verifies that the correct device exists and functions. */
151
152static int __init seeq8005_probe1(struct net_device *dev, int ioaddr)
153{
154 static unsigned version_printed;
155 int i,j;
156 unsigned char SA_prom[32];
157 int old_cfg1;
158 int old_cfg2;
159 int old_stat;
160 int old_dmaar;
161 int old_rear;
162 int retval;
163
164 if (!request_region(ioaddr, SEEQ8005_IO_EXTENT, "seeq8005"))
165 return -ENODEV;
166
167 if (net_debug>1)
168 printk("seeq8005: probing at 0x%x\n",ioaddr);
169
170 old_stat = inw(SEEQ_STATUS); /* read status register */
171 if (old_stat == 0xffff) {
172 retval = -ENODEV;
173 goto out; /* assume that 0xffff == no device */
174 }
175 if ( (old_stat & 0x1800) != 0x1800 ) { /* assume that unused bits are 1, as my manual says */
176 if (net_debug>1) {
177 printk("seeq8005: reserved stat bits != 0x1800\n");
178 printk(" == 0x%04x\n",old_stat);
179 }
180 retval = -ENODEV;
181 goto out;
182 }
183
184 old_rear = inw(SEEQ_REA);
185 if (old_rear == 0xffff) {
186 outw(0,SEEQ_REA);
187 if (inw(SEEQ_REA) == 0xffff) { /* assume that 0xffff == no device */
188 retval = -ENODEV;
189 goto out;
190 }
191 } else if ((old_rear & 0xff00) != 0xff00) { /* assume that unused bits are 1 */
192 if (net_debug>1) {
193 printk("seeq8005: unused rear bits != 0xff00\n");
194 printk(" == 0x%04x\n",old_rear);
195 }
196 retval = -ENODEV;
197 goto out;
198 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400199
Linus Torvalds1da177e2005-04-16 15:20:36 -0700200 old_cfg2 = inw(SEEQ_CFG2); /* read CFG2 register */
201 old_cfg1 = inw(SEEQ_CFG1);
202 old_dmaar = inw(SEEQ_DMAAR);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400203
Linus Torvalds1da177e2005-04-16 15:20:36 -0700204 if (net_debug>4) {
205 printk("seeq8005: stat = 0x%04x\n",old_stat);
206 printk("seeq8005: cfg1 = 0x%04x\n",old_cfg1);
207 printk("seeq8005: cfg2 = 0x%04x\n",old_cfg2);
208 printk("seeq8005: raer = 0x%04x\n",old_rear);
209 printk("seeq8005: dmaar= 0x%04x\n",old_dmaar);
210 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400211
Linus Torvalds1da177e2005-04-16 15:20:36 -0700212 outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD); /* setup for reading PROM */
213 outw( 0, SEEQ_DMAAR); /* set starting PROM address */
214 outw( SEEQCFG1_BUFFER_PROM, SEEQ_CFG1); /* set buffer to look at PROM */
215
216
217 j=0;
218 for(i=0; i <32; i++) {
219 j+= SA_prom[i] = inw(SEEQ_BUFFER) & 0xff;
220 }
221
222#if 0
223 /* untested because I only have the one card */
224 if ( (j&0xff) != 0 ) { /* checksum appears to be 8bit = 0 */
225 if (net_debug>1) { /* check this before deciding that we have a card */
226 printk("seeq8005: prom sum error\n");
227 }
228 outw( old_stat, SEEQ_STATUS);
229 outw( old_dmaar, SEEQ_DMAAR);
230 outw( old_cfg1, SEEQ_CFG1);
231 retval = -ENODEV;
232 goto out;
233 }
234#endif
235
236 outw( SEEQCFG2_RESET, SEEQ_CFG2); /* reset the card */
237 udelay(5);
238 outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400239
Linus Torvalds1da177e2005-04-16 15:20:36 -0700240 if (net_debug) {
241 printk("seeq8005: prom sum = 0x%08x\n",j);
242 for(j=0; j<32; j+=16) {
243 printk("seeq8005: prom %02x: ",j);
244 for(i=0;i<16;i++) {
245 printk("%02x ",SA_prom[j|i]);
246 }
247 printk(" ");
248 for(i=0;i<16;i++) {
249 if ((SA_prom[j|i]>31)&&(SA_prom[j|i]<127)) {
250 printk("%c", SA_prom[j|i]);
251 } else {
252 printk(" ");
253 }
254 }
255 printk("\n");
256 }
257 }
258
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400259#if 0
260 /*
Linus Torvalds1da177e2005-04-16 15:20:36 -0700261 * testing the packet buffer memory doesn't work yet
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400262 * but all other buffer accesses do
Linus Torvalds1da177e2005-04-16 15:20:36 -0700263 * - fixing is not a priority
264 */
265 if (net_debug>1) { /* test packet buffer memory */
266 printk("seeq8005: testing packet buffer ... ");
267 outw( SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1);
268 outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
269 outw( 0 , SEEQ_DMAAR);
270 for(i=0;i<32768;i++) {
271 outw(0x5a5a, SEEQ_BUFFER);
272 }
273 j=jiffies+HZ;
274 while ( ((inw(SEEQ_STATUS) & SEEQSTAT_FIFO_EMPTY) != SEEQSTAT_FIFO_EMPTY) && time_before(jiffies, j) )
275 mb();
276 outw( 0 , SEEQ_DMAAR);
277 while ( ((inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, j+HZ))
278 mb();
279 if ( (inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT)
280 outw( SEEQCMD_WINDOW_INT_ACK | (inw(SEEQ_STATUS)& SEEQCMD_INT_MASK), SEEQ_CMD);
281 outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
282 j=0;
283 for(i=0;i<32768;i++) {
284 if (inw(SEEQ_BUFFER) != 0x5a5a)
285 j++;
286 }
287 if (j) {
288 printk("%i\n",j);
289 } else {
290 printk("ok.\n");
291 }
292 }
293#endif
294
295 if (net_debug && version_printed++ == 0)
296 printk(version);
297
298 printk("%s: %s found at %#3x, ", dev->name, "seeq8005", ioaddr);
299
300 /* Fill in the 'dev' fields. */
301 dev->base_addr = ioaddr;
302 dev->irq = irq;
303
304 /* Retrieve and print the ethernet address. */
305 for (i = 0; i < 6; i++)
306 printk(" %2.2x", dev->dev_addr[i] = SA_prom[i+6]);
307
308 if (dev->irq == 0xff)
309 ; /* Do nothing: a user-level program will set it. */
310 else if (dev->irq < 2) { /* "Auto-IRQ" */
311 unsigned long cookie = probe_irq_on();
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400312
Linus Torvalds1da177e2005-04-16 15:20:36 -0700313 outw( SEEQCMD_RX_INT_EN | SEEQCMD_SET_RX_ON | SEEQCMD_SET_RX_OFF, SEEQ_CMD );
314
315 dev->irq = probe_irq_off(cookie);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400316
Linus Torvalds1da177e2005-04-16 15:20:36 -0700317 if (net_debug >= 2)
318 printk(" autoirq is %d\n", dev->irq);
319 } else if (dev->irq == 2)
320 /* Fixup for users that don't know that IRQ 2 is really IRQ 9,
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400321 * or don't know which one to set.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700322 */
323 dev->irq = 9;
324
325#if 0
326 {
327 int irqval = request_irq(dev->irq, &seeq8005_interrupt, 0, "seeq8005", dev);
328 if (irqval) {
329 printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
330 dev->irq, irqval);
331 retval = -EAGAIN;
332 goto out;
333 }
334 }
335#endif
336 dev->open = seeq8005_open;
337 dev->stop = seeq8005_close;
338 dev->hard_start_xmit = seeq8005_send_packet;
339 dev->tx_timeout = seeq8005_timeout;
340 dev->watchdog_timeo = HZ/20;
341 dev->get_stats = seeq8005_get_stats;
342 dev->set_multicast_list = set_multicast_list;
343 dev->flags &= ~IFF_MULTICAST;
344
345 return 0;
346out:
347 release_region(ioaddr, SEEQ8005_IO_EXTENT);
348 return retval;
349}
350
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400351
Linus Torvalds1da177e2005-04-16 15:20:36 -0700352/* Open/initialize the board. This is called (in the current kernel)
353 sometime after booting when the 'ifconfig' program is run.
354
355 This routine should set everything up anew at each open, even
356 registers that "should" only need to be set once at boot, so that
357 there is non-reboot way to recover if something goes wrong.
358 */
359static int seeq8005_open(struct net_device *dev)
360{
361 struct net_local *lp = netdev_priv(dev);
362
363 {
364 int irqval = request_irq(dev->irq, &seeq8005_interrupt, 0, "seeq8005", dev);
365 if (irqval) {
366 printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
367 dev->irq, irqval);
368 return -EAGAIN;
369 }
370 }
371
372 /* Reset the hardware here. Don't forget to set the station address. */
373 seeq8005_init(dev, 1);
374
375 lp->open_time = jiffies;
376
377 netif_start_queue(dev);
378 return 0;
379}
380
381static void seeq8005_timeout(struct net_device *dev)
382{
383 int ioaddr = dev->base_addr;
384 printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name,
385 tx_done(dev) ? "IRQ conflict" : "network cable problem");
386 /* Try to restart the adaptor. */
387 seeq8005_init(dev, 1);
388 dev->trans_start = jiffies;
389 netif_wake_queue(dev);
390}
391
392static int seeq8005_send_packet(struct sk_buff *skb, struct net_device *dev)
393{
394 struct net_local *lp = netdev_priv(dev);
395 short length = skb->len;
396 unsigned char *buf;
397
398 if (length < ETH_ZLEN) {
Herbert Xu5b057c62006-06-23 02:06:41 -0700399 if (skb_padto(skb, ETH_ZLEN))
Linus Torvalds1da177e2005-04-16 15:20:36 -0700400 return 0;
401 length = ETH_ZLEN;
402 }
403 buf = skb->data;
404
405 /* Block a timer-based transmit from overlapping */
406 netif_stop_queue(dev);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400407
408 hardware_send_packet(dev, buf, length);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700409 dev->trans_start = jiffies;
410 lp->stats.tx_bytes += length;
411 dev_kfree_skb (skb);
412 /* You might need to clean up and record Tx statistics here. */
413
414 return 0;
415}
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400416
Linus Torvalds1da177e2005-04-16 15:20:36 -0700417/*
418 * wait_for_buffer
419 *
420 * This routine waits for the SEEQ chip to assert that the FIFO is ready
421 * by checking for a window interrupt, and then clearing it. This has to
422 * occur in the interrupt handler!
423 */
424inline void wait_for_buffer(struct net_device * dev)
425{
426 int ioaddr = dev->base_addr;
427 unsigned long tmp;
428 int status;
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400429
Linus Torvalds1da177e2005-04-16 15:20:36 -0700430 tmp = jiffies + HZ;
431 while ( ( ((status=inw(SEEQ_STATUS)) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, tmp))
432 cpu_relax();
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400433
Linus Torvalds1da177e2005-04-16 15:20:36 -0700434 if ( (status & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT)
435 outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
436}
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400437
Linus Torvalds1da177e2005-04-16 15:20:36 -0700438/* The typical workload of the driver:
439 Handle the network interface interrupts. */
David Howells7d12e782006-10-05 14:55:46 +0100440static irqreturn_t seeq8005_interrupt(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700441{
442 struct net_device *dev = dev_id;
443 struct net_local *lp;
444 int ioaddr, status, boguscount = 0;
445 int handled = 0;
446
447 ioaddr = dev->base_addr;
448 lp = netdev_priv(dev);
449
450 status = inw(SEEQ_STATUS);
451 do {
452 if (net_debug >2) {
453 printk("%s: int, status=0x%04x\n",dev->name,status);
454 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400455
Linus Torvalds1da177e2005-04-16 15:20:36 -0700456 if (status & SEEQSTAT_WINDOW_INT) {
457 handled = 1;
458 outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
459 if (net_debug) {
460 printk("%s: window int!\n",dev->name);
461 }
462 }
463 if (status & SEEQSTAT_TX_INT) {
464 handled = 1;
465 outw( SEEQCMD_TX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
466 lp->stats.tx_packets++;
467 netif_wake_queue(dev); /* Inform upper layers. */
468 }
469 if (status & SEEQSTAT_RX_INT) {
470 handled = 1;
471 /* Got a packet(s). */
472 seeq8005_rx(dev);
473 }
474 status = inw(SEEQ_STATUS);
475 } while ( (++boguscount < 10) && (status & SEEQSTAT_ANY_INT)) ;
476
477 if(net_debug>2) {
478 printk("%s: eoi\n",dev->name);
479 }
480 return IRQ_RETVAL(handled);
481}
482
483/* We have a good packet(s), get it/them out of the buffers. */
484static void seeq8005_rx(struct net_device *dev)
485{
486 struct net_local *lp = netdev_priv(dev);
487 int boguscount = 10;
488 int pkt_hdr;
489 int ioaddr = dev->base_addr;
490
491 do {
492 int next_packet;
493 int pkt_len;
494 int i;
495 int status;
496
497 status = inw(SEEQ_STATUS);
498 outw( lp->receive_ptr, SEEQ_DMAAR);
499 outw(SEEQCMD_FIFO_READ | SEEQCMD_RX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
500 wait_for_buffer(dev);
501 next_packet = ntohs(inw(SEEQ_BUFFER));
502 pkt_hdr = inw(SEEQ_BUFFER);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400503
Linus Torvalds1da177e2005-04-16 15:20:36 -0700504 if (net_debug>2) {
505 printk("%s: 0x%04x recv next=0x%04x, hdr=0x%04x\n",dev->name,lp->receive_ptr,next_packet,pkt_hdr);
506 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400507
Linus Torvalds1da177e2005-04-16 15:20:36 -0700508 if ((next_packet == 0) || ((pkt_hdr & SEEQPKTH_CHAIN)==0)) { /* Read all the frames? */
509 return; /* Done for now */
510 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400511
Linus Torvalds1da177e2005-04-16 15:20:36 -0700512 if ((pkt_hdr & SEEQPKTS_DONE)==0)
513 break;
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400514
Linus Torvalds1da177e2005-04-16 15:20:36 -0700515 if (next_packet < lp->receive_ptr) {
516 pkt_len = (next_packet + 0x10000 - ((DEFAULT_TEA+1)<<8)) - lp->receive_ptr - 4;
517 } else {
518 pkt_len = next_packet - lp->receive_ptr - 4;
519 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400520
Linus Torvalds1da177e2005-04-16 15:20:36 -0700521 if (next_packet < ((DEFAULT_TEA+1)<<8)) { /* is the next_packet address sane? */
522 printk("%s: recv packet ring corrupt, resetting board\n",dev->name);
523 seeq8005_init(dev,1);
524 return;
525 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400526
Linus Torvalds1da177e2005-04-16 15:20:36 -0700527 lp->receive_ptr = next_packet;
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400528
Linus Torvalds1da177e2005-04-16 15:20:36 -0700529 if (net_debug>2) {
530 printk("%s: recv len=0x%04x\n",dev->name,pkt_len);
531 }
532
533 if (pkt_hdr & SEEQPKTS_ANY_ERROR) { /* There was an error. */
534 lp->stats.rx_errors++;
535 if (pkt_hdr & SEEQPKTS_SHORT) lp->stats.rx_frame_errors++;
536 if (pkt_hdr & SEEQPKTS_DRIB) lp->stats.rx_frame_errors++;
537 if (pkt_hdr & SEEQPKTS_OVERSIZE) lp->stats.rx_over_errors++;
538 if (pkt_hdr & SEEQPKTS_CRC_ERR) lp->stats.rx_crc_errors++;
539 /* skip over this packet */
540 outw( SEEQCMD_FIFO_WRITE | SEEQCMD_DMA_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
541 outw( (lp->receive_ptr & 0xff00)>>8, SEEQ_REA);
542 } else {
543 /* Malloc up new buffer. */
544 struct sk_buff *skb;
545 unsigned char *buf;
546
547 skb = dev_alloc_skb(pkt_len);
548 if (skb == NULL) {
549 printk("%s: Memory squeeze, dropping packet.\n", dev->name);
550 lp->stats.rx_dropped++;
551 break;
552 }
553 skb->dev = dev;
554 skb_reserve(skb, 2); /* align data on 16 byte */
555 buf = skb_put(skb,pkt_len);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400556
Linus Torvalds1da177e2005-04-16 15:20:36 -0700557 insw(SEEQ_BUFFER, buf, (pkt_len + 1) >> 1);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400558
Linus Torvalds1da177e2005-04-16 15:20:36 -0700559 if (net_debug>2) {
560 char * p = buf;
561 printk("%s: recv ",dev->name);
562 for(i=0;i<14;i++) {
563 printk("%02x ",*(p++)&0xff);
564 }
565 printk("\n");
566 }
567
568 skb->protocol=eth_type_trans(skb,dev);
569 netif_rx(skb);
570 dev->last_rx = jiffies;
571 lp->stats.rx_packets++;
572 lp->stats.rx_bytes += pkt_len;
573 }
574 } while ((--boguscount) && (pkt_hdr & SEEQPKTH_CHAIN));
575
576 /* If any worth-while packets have been received, netif_rx()
577 has done a mark_bh(NET_BH) for us and will work on them
578 when we get to the bottom-half routine. */
579 return;
580}
581
582/* The inverse routine to net_open(). */
583static int seeq8005_close(struct net_device *dev)
584{
585 struct net_local *lp = netdev_priv(dev);
586 int ioaddr = dev->base_addr;
587
588 lp->open_time = 0;
589
590 netif_stop_queue(dev);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400591
Linus Torvalds1da177e2005-04-16 15:20:36 -0700592 /* Flush the Tx and disable Rx here. */
593 outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
594
595 free_irq(dev->irq, dev);
596
597 /* Update the statistics here. */
598
599 return 0;
600
601}
602
603/* Get the current statistics. This may be called with the card open or
604 closed. */
605static struct net_device_stats *seeq8005_get_stats(struct net_device *dev)
606{
607 struct net_local *lp = netdev_priv(dev);
608
609 return &lp->stats;
610}
611
612/* Set or clear the multicast filter for this adaptor.
613 num_addrs == -1 Promiscuous mode, receive all packets
614 num_addrs == 0 Normal mode, clear multicast list
615 num_addrs > 0 Multicast mode, receive normal and MC packets, and do
616 best-effort filtering.
617 */
618static void set_multicast_list(struct net_device *dev)
619{
620/*
621 * I _could_ do up to 6 addresses here, but won't (yet?)
622 */
623
624#if 0
625 int ioaddr = dev->base_addr;
626/*
627 * hmm, not even sure if my matching works _anyway_ - seem to be receiving
628 * _everything_ . . .
629 */
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400630
Linus Torvalds1da177e2005-04-16 15:20:36 -0700631 if (num_addrs) { /* Enable promiscuous mode */
632 outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_ALL, SEEQ_CFG1);
633 dev->flags|=IFF_PROMISC;
634 } else { /* Disable promiscuous mode, use normal mode */
635 outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_BROAD, SEEQ_CFG1);
636 }
637#endif
638}
639
640void seeq8005_init(struct net_device *dev, int startp)
641{
642 struct net_local *lp = netdev_priv(dev);
643 int ioaddr = dev->base_addr;
644 int i;
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400645
Linus Torvalds1da177e2005-04-16 15:20:36 -0700646 outw(SEEQCFG2_RESET, SEEQ_CFG2); /* reset device */
647 udelay(5);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400648
Linus Torvalds1da177e2005-04-16 15:20:36 -0700649 outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
650 outw( 0, SEEQ_DMAAR); /* load start address into both low and high byte */
651/* wait_for_buffer(dev); */ /* I think that you only need a wait for memory buffer */
652 outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400653
Linus Torvalds1da177e2005-04-16 15:20:36 -0700654 for(i=0;i<6;i++) { /* set Station address */
655 outb(dev->dev_addr[i], SEEQ_BUFFER);
656 udelay(2);
657 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400658
Linus Torvalds1da177e2005-04-16 15:20:36 -0700659 outw( SEEQCFG1_BUFFER_TEA, SEEQ_CFG1); /* set xmit end area pointer to 16K */
660 outb( DEFAULT_TEA, SEEQ_BUFFER); /* this gives us 16K of send buffer and 48K of recv buffer */
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400661
Linus Torvalds1da177e2005-04-16 15:20:36 -0700662 lp->receive_ptr = (DEFAULT_TEA+1)<<8; /* so we can find our packet_header */
663 outw( lp->receive_ptr, SEEQ_RPR); /* Receive Pointer Register is set to recv buffer memory */
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400664
Linus Torvalds1da177e2005-04-16 15:20:36 -0700665 outw( 0x00ff, SEEQ_REA); /* Receive Area End */
666
667 if (net_debug>4) {
668 printk("%s: SA0 = ",dev->name);
669
670 outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
671 outw( 0, SEEQ_DMAAR);
672 outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400673
Linus Torvalds1da177e2005-04-16 15:20:36 -0700674 for(i=0;i<6;i++) {
675 printk("%02x ",inb(SEEQ_BUFFER));
676 }
677 printk("\n");
678 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400679
Linus Torvalds1da177e2005-04-16 15:20:36 -0700680 outw( SEEQCFG1_MAC0_EN | SEEQCFG1_MATCH_BROAD | SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1);
681 outw( SEEQCFG2_AUTO_REA | SEEQCFG2_CTRLO, SEEQ_CFG2);
682 outw( SEEQCMD_SET_RX_ON | SEEQCMD_TX_INT_EN | SEEQCMD_RX_INT_EN, SEEQ_CMD);
683
684 if (net_debug>4) {
685 int old_cfg1;
686 old_cfg1 = inw(SEEQ_CFG1);
687 printk("%s: stat = 0x%04x\n",dev->name,inw(SEEQ_STATUS));
688 printk("%s: cfg1 = 0x%04x\n",dev->name,old_cfg1);
689 printk("%s: cfg2 = 0x%04x\n",dev->name,inw(SEEQ_CFG2));
690 printk("%s: raer = 0x%04x\n",dev->name,inw(SEEQ_REA));
691 printk("%s: dmaar= 0x%04x\n",dev->name,inw(SEEQ_DMAAR));
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400692
Linus Torvalds1da177e2005-04-16 15:20:36 -0700693 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400694}
Linus Torvalds1da177e2005-04-16 15:20:36 -0700695
696
697static void hardware_send_packet(struct net_device * dev, char *buf, int length)
698{
699 int ioaddr = dev->base_addr;
700 int status = inw(SEEQ_STATUS);
701 int transmit_ptr = 0;
Marcelo Feitoza Parisiff5688a2006-01-09 18:37:15 -0800702 unsigned long tmp;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700703
704 if (net_debug>4) {
705 printk("%s: send 0x%04x\n",dev->name,length);
706 }
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400707
Linus Torvalds1da177e2005-04-16 15:20:36 -0700708 /* Set FIFO to writemode and set packet-buffer address */
709 outw( SEEQCMD_FIFO_WRITE | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
710 outw( transmit_ptr, SEEQ_DMAAR);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400711
Linus Torvalds1da177e2005-04-16 15:20:36 -0700712 /* output SEEQ Packet header barfage */
713 outw( htons(length + 4), SEEQ_BUFFER);
714 outw( SEEQPKTH_XMIT | SEEQPKTH_DATA_FOLLOWS | SEEQPKTH_XMIT_INT_EN, SEEQ_BUFFER );
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400715
Linus Torvalds1da177e2005-04-16 15:20:36 -0700716 /* blat the buffer */
717 outsw( SEEQ_BUFFER, buf, (length +1) >> 1);
718 /* paranoia !! */
719 outw( 0, SEEQ_BUFFER);
720 outw( 0, SEEQ_BUFFER);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400721
Linus Torvalds1da177e2005-04-16 15:20:36 -0700722 /* set address of start of transmit chain */
723 outw( transmit_ptr, SEEQ_TPR);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400724
Linus Torvalds1da177e2005-04-16 15:20:36 -0700725 /* drain FIFO */
726 tmp = jiffies;
Marcelo Feitoza Parisiff5688a2006-01-09 18:37:15 -0800727 while ( (((status=inw(SEEQ_STATUS)) & SEEQSTAT_FIFO_EMPTY) == 0) && time_before(jiffies, tmp + HZ))
Linus Torvalds1da177e2005-04-16 15:20:36 -0700728 mb();
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400729
Linus Torvalds1da177e2005-04-16 15:20:36 -0700730 /* doit ! */
731 outw( SEEQCMD_WINDOW_INT_ACK | SEEQCMD_SET_TX_ON | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400732
Linus Torvalds1da177e2005-04-16 15:20:36 -0700733}
734
735
736#ifdef MODULE
737
738static struct net_device *dev_seeq;
739MODULE_LICENSE("GPL");
740module_param(io, int, 0);
741module_param(irq, int, 0);
742MODULE_PARM_DESC(io, "SEEQ 8005 I/O base address");
743MODULE_PARM_DESC(irq, "SEEQ 8005 IRQ number");
744
Andrew Mortonc971ef42006-08-14 23:00:08 -0700745int __init init_module(void)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700746{
747 dev_seeq = seeq8005_probe(-1);
748 if (IS_ERR(dev_seeq))
749 return PTR_ERR(dev_seeq);
750 return 0;
751}
752
753void cleanup_module(void)
754{
755 unregister_netdev(dev_seeq);
756 release_region(dev_seeq->base_addr, SEEQ8005_IO_EXTENT);
757 free_netdev(dev_seeq);
758}
759
760#endif /* MODULE */
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400761
Linus Torvalds1da177e2005-04-16 15:20:36 -0700762/*
763 * Local variables:
764 * compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c skeleton.c"
765 * version-control: t
766 * kept-new-versions: 5
767 * tab-width: 4
768 * End:
769 */