blob: 487d780ebbdfd73768f575e43353da5f2e8a1fa3 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * Linux ARCnet driver - COM90xx chipset (IO-mapped buffers)
3 *
4 * Written 1997 by David Woodhouse.
5 * Written 1994-1999 by Avery Pennarun.
6 * Written 1999-2000 by Martin Mares <mj@ucw.cz>.
7 * Derived from skeleton.c by Donald Becker.
8 *
9 * Special thanks to Contemporary Controls, Inc. (www.ccontrols.com)
10 * for sponsoring the further development of this driver.
11 *
12 * **********************
13 *
14 * The original copyright of skeleton.c was as follows:
15 *
16 * skeleton.c Written 1993 by Donald Becker.
17 * Copyright 1993 United States Government as represented by the
18 * Director, National Security Agency. This software may only be used
19 * and distributed according to the terms of the GNU General Public License as
20 * modified by SRC, incorporated herein by reference.
21 *
22 * **********************
23 *
24 * For more details, see drivers/net/arcnet.c
25 *
26 * **********************
27 */
28#include <linux/kernel.h>
29#include <linux/module.h>
30#include <linux/moduleparam.h>
31#include <linux/ioport.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070032#include <linux/delay.h>
33#include <linux/netdevice.h>
34#include <linux/bootmem.h>
35#include <linux/init.h>
Alexey Dobriyana6b7a402011-06-06 10:43:46 +000036#include <linux/interrupt.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070037#include <asm/io.h>
38#include <linux/arcdevice.h>
39
40
41#define VERSION "arcnet: COM90xx IO-mapped mode support (by David Woodhouse et el.)\n"
42
43
44/* Internal function declarations */
45
46static int com90io_found(struct net_device *dev);
47static void com90io_command(struct net_device *dev, int command);
48static int com90io_status(struct net_device *dev);
49static void com90io_setmask(struct net_device *dev, int mask);
50static int com90io_reset(struct net_device *dev, int really_reset);
51static void com90io_copy_to_card(struct net_device *dev, int bufnum, int offset,
52 void *buf, int count);
53static void com90io_copy_from_card(struct net_device *dev, int bufnum, int offset,
54 void *buf, int count);
55
56
57/* Handy defines for ARCnet specific stuff */
58
59/* The number of low I/O ports used by the card. */
60#define ARCNET_TOTAL_SIZE 16
61
62/* COM 9026 controller chip --> ARCnet register addresses */
63#define _INTMASK (ioaddr+0) /* writable */
64#define _STATUS (ioaddr+0) /* readable */
65#define _COMMAND (ioaddr+1) /* writable, returns random vals on read (?) */
66#define _RESET (ioaddr+8) /* software reset (on read) */
67#define _MEMDATA (ioaddr+12) /* Data port for IO-mapped memory */
68#define _ADDR_HI (ioaddr+15) /* Control registers for said */
69#define _ADDR_LO (ioaddr+14)
70#define _CONFIG (ioaddr+2) /* Configuration register */
71
72#undef ASTATUS
73#undef ACOMMAND
74#undef AINTMASK
75
76#define ASTATUS() inb(_STATUS)
77#define ACOMMAND(cmd) outb((cmd),_COMMAND)
78#define AINTMASK(msk) outb((msk),_INTMASK)
79#define SETCONF() outb((lp->config),_CONFIG)
80
81
82/****************************************************************************
83 * *
84 * IO-mapped operation routines *
85 * *
86 ****************************************************************************/
87
88#undef ONE_AT_A_TIME_TX
89#undef ONE_AT_A_TIME_RX
90
91static u_char get_buffer_byte(struct net_device *dev, unsigned offset)
92{
93 int ioaddr = dev->base_addr;
94
95 outb(offset >> 8, _ADDR_HI);
96 outb(offset & 0xff, _ADDR_LO);
97
98 return inb(_MEMDATA);
99}
100
101#ifdef ONE_AT_A_TIME_TX
102static void put_buffer_byte(struct net_device *dev, unsigned offset, u_char datum)
103{
104 int ioaddr = dev->base_addr;
105
106 outb(offset >> 8, _ADDR_HI);
107 outb(offset & 0xff, _ADDR_LO);
108
109 outb(datum, _MEMDATA);
110}
111
112#endif
113
114
115static void get_whole_buffer(struct net_device *dev, unsigned offset, unsigned length, char *dest)
116{
117 int ioaddr = dev->base_addr;
118
119 outb((offset >> 8) | AUTOINCflag, _ADDR_HI);
120 outb(offset & 0xff, _ADDR_LO);
121
122 while (length--)
123#ifdef ONE_AT_A_TIME_RX
124 *(dest++) = get_buffer_byte(dev, offset++);
125#else
126 *(dest++) = inb(_MEMDATA);
127#endif
128}
129
130static void put_whole_buffer(struct net_device *dev, unsigned offset, unsigned length, char *dest)
131{
132 int ioaddr = dev->base_addr;
133
134 outb((offset >> 8) | AUTOINCflag, _ADDR_HI);
135 outb(offset & 0xff, _ADDR_LO);
136
137 while (length--)
138#ifdef ONE_AT_A_TIME_TX
139 put_buffer_byte(dev, offset++, *(dest++));
140#else
141 outb(*(dest++), _MEMDATA);
142#endif
143}
144
145/*
146 * We cannot probe for an IO mapped card either, although we can check that
147 * it's where we were told it was, and even autoirq
148 */
149static int __init com90io_probe(struct net_device *dev)
150{
151 int ioaddr = dev->base_addr, status;
152 unsigned long airqmask;
153
154 BUGLVL(D_NORMAL) printk(VERSION);
155 BUGLVL(D_NORMAL) printk("E-mail me if you actually test this driver, please!\n");
156
157 if (!ioaddr) {
158 BUGMSG(D_NORMAL, "No autoprobe for IO mapped cards; you "
159 "must specify the base address!\n");
160 return -ENODEV;
161 }
162 if (!request_region(ioaddr, ARCNET_TOTAL_SIZE, "com90io probe")) {
Peter Osterlundfb911ee2005-09-13 01:25:15 -0700163 BUGMSG(D_INIT_REASONS, "IO request_region %x-%x failed.\n",
Linus Torvalds1da177e2005-04-16 15:20:36 -0700164 ioaddr, ioaddr + ARCNET_TOTAL_SIZE - 1);
165 return -ENXIO;
166 }
167 if (ASTATUS() == 0xFF) {
168 BUGMSG(D_INIT_REASONS, "IO address %x empty\n", ioaddr);
169 goto err_out;
170 }
171 inb(_RESET);
172 mdelay(RESETtime);
173
174 status = ASTATUS();
175
176 if ((status & 0x9D) != (NORXflag | RECONflag | TXFREEflag | RESETflag)) {
177 BUGMSG(D_INIT_REASONS, "Status invalid (%Xh).\n", status);
178 goto err_out;
179 }
180 BUGMSG(D_INIT_REASONS, "Status after reset: %X\n", status);
181
182 ACOMMAND(CFLAGScmd | RESETclear | CONFIGclear);
183
184 BUGMSG(D_INIT_REASONS, "Status after reset acknowledged: %X\n", status);
185
186 status = ASTATUS();
187
188 if (status & RESETflag) {
189 BUGMSG(D_INIT_REASONS, "Eternal reset (status=%Xh)\n", status);
190 goto err_out;
191 }
192 outb((0x16 | IOMAPflag) & ~ENABLE16flag, _CONFIG);
193
194 /* Read first loc'n of memory */
195
196 outb(AUTOINCflag, _ADDR_HI);
197 outb(0, _ADDR_LO);
198
199 if ((status = inb(_MEMDATA)) != 0xd1) {
200 BUGMSG(D_INIT_REASONS, "Signature byte not found"
201 " (%Xh instead).\n", status);
202 goto err_out;
203 }
204 if (!dev->irq) {
205 /*
206 * if we do this, we're sure to get an IRQ since the
207 * card has just reset and the NORXflag is on until
208 * we tell it to start receiving.
209 */
210
211 airqmask = probe_irq_on();
212 outb(NORXflag, _INTMASK);
213 udelay(1);
214 outb(0, _INTMASK);
215 dev->irq = probe_irq_off(airqmask);
216
Dan Carpenter0a6efc72010-07-17 07:21:28 +0000217 if ((int)dev->irq <= 0) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700218 BUGMSG(D_INIT_REASONS, "Autoprobe IRQ failed\n");
219 goto err_out;
220 }
221 }
222 release_region(ioaddr, ARCNET_TOTAL_SIZE); /* end of probing */
223 return com90io_found(dev);
224
225err_out:
226 release_region(ioaddr, ARCNET_TOTAL_SIZE);
227 return -ENODEV;
228}
229
230
231/* Set up the struct net_device associated with this card. Called after
232 * probing succeeds.
233 */
234static int __init com90io_found(struct net_device *dev)
235{
236 struct arcnet_local *lp;
237 int ioaddr = dev->base_addr;
238 int err;
239
240 /* Reserve the irq */
Joe Perchesa0607fd2009-11-18 23:29:17 -0800241 if (request_irq(dev->irq, arcnet_interrupt, 0, "arcnet (COM90xx-IO)", dev)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700242 BUGMSG(D_NORMAL, "Can't get IRQ %d!\n", dev->irq);
243 return -ENODEV;
244 }
Peter Osterlundfb911ee2005-09-13 01:25:15 -0700245 /* Reserve the I/O region */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700246 if (!request_region(dev->base_addr, ARCNET_TOTAL_SIZE, "arcnet (COM90xx-IO)")) {
247 free_irq(dev->irq, dev);
248 return -EBUSY;
249 }
250
Wang Chen454d7c92008-11-12 23:37:49 -0800251 lp = netdev_priv(dev);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700252 lp->card_name = "COM90xx I/O";
253 lp->hw.command = com90io_command;
254 lp->hw.status = com90io_status;
255 lp->hw.intmask = com90io_setmask;
256 lp->hw.reset = com90io_reset;
257 lp->hw.owner = THIS_MODULE;
258 lp->hw.copy_to_card = com90io_copy_to_card;
259 lp->hw.copy_from_card = com90io_copy_from_card;
260
261 lp->config = (0x16 | IOMAPflag) & ~ENABLE16flag;
262 SETCONF();
263
264 /* get and check the station ID from offset 1 in shmem */
265
266 dev->dev_addr[0] = get_buffer_byte(dev, 1);
267
268 err = register_netdev(dev);
269 if (err) {
270 outb((inb(_CONFIG) & ~IOMAPflag), _CONFIG);
271 free_irq(dev->irq, dev);
272 release_region(dev->base_addr, ARCNET_TOTAL_SIZE);
273 return err;
274 }
275
276 BUGMSG(D_NORMAL, "COM90IO: station %02Xh found at %03lXh, IRQ %d.\n",
277 dev->dev_addr[0], dev->base_addr, dev->irq);
278
279 return 0;
280}
281
282
283/*
284 * Do a hardware reset on the card, and set up necessary registers.
285 *
286 * This should be called as little as possible, because it disrupts the
287 * token on the network (causes a RECON) and requires a significant delay.
288 *
289 * However, it does make sure the card is in a defined state.
290 */
291static int com90io_reset(struct net_device *dev, int really_reset)
292{
Wang Chen454d7c92008-11-12 23:37:49 -0800293 struct arcnet_local *lp = netdev_priv(dev);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700294 short ioaddr = dev->base_addr;
295
296 BUGMSG(D_INIT, "Resetting %s (status=%02Xh)\n", dev->name, ASTATUS());
297
298 if (really_reset) {
299 /* reset the card */
300 inb(_RESET);
301 mdelay(RESETtime);
302 }
303 /* Set the thing to IO-mapped, 8-bit mode */
304 lp->config = (0x1C | IOMAPflag) & ~ENABLE16flag;
305 SETCONF();
306
307 ACOMMAND(CFLAGScmd | RESETclear); /* clear flags & end reset */
308 ACOMMAND(CFLAGScmd | CONFIGclear);
309
310 /* verify that the ARCnet signature byte is present */
311 if (get_buffer_byte(dev, 0) != TESTvalue) {
312 BUGMSG(D_NORMAL, "reset failed: TESTvalue not present.\n");
313 return 1;
314 }
315 /* enable extended (512-byte) packets */
316 ACOMMAND(CONFIGcmd | EXTconf);
317
318 /* done! return success. */
319 return 0;
320}
321
322
323static void com90io_command(struct net_device *dev, int cmd)
324{
325 short ioaddr = dev->base_addr;
326
327 ACOMMAND(cmd);
328}
329
330
331static int com90io_status(struct net_device *dev)
332{
333 short ioaddr = dev->base_addr;
334
335 return ASTATUS();
336}
337
338
339static void com90io_setmask(struct net_device *dev, int mask)
340{
341 short ioaddr = dev->base_addr;
342
343 AINTMASK(mask);
344}
345
346static void com90io_copy_to_card(struct net_device *dev, int bufnum, int offset,
347 void *buf, int count)
348{
349 TIME("put_whole_buffer", count, put_whole_buffer(dev, bufnum * 512 + offset, count, buf));
350}
351
352
353static void com90io_copy_from_card(struct net_device *dev, int bufnum, int offset,
354 void *buf, int count)
355{
356 TIME("get_whole_buffer", count, get_whole_buffer(dev, bufnum * 512 + offset, count, buf));
357}
358
359static int io; /* use the insmod io= irq= shmem= options */
360static int irq;
361static char device[9]; /* use eg. device=arc1 to change name */
362
363module_param(io, int, 0);
364module_param(irq, int, 0);
365module_param_string(device, device, sizeof(device), 0);
366MODULE_LICENSE("GPL");
367
368#ifndef MODULE
369static int __init com90io_setup(char *s)
370{
371 int ints[4];
372 s = get_options(s, 4, ints);
373 if (!ints[0])
374 return 0;
375 switch (ints[0]) {
376 default: /* ERROR */
377 printk("com90io: Too many arguments.\n");
378 case 2: /* IRQ */
379 irq = ints[2];
380 case 1: /* IO address */
381 io = ints[1];
382 }
383 if (*s)
384 snprintf(device, sizeof(device), "%s", s);
385 return 1;
386}
387__setup("com90io=", com90io_setup);
388#endif
389
390static struct net_device *my_dev;
391
392static int __init com90io_init(void)
393{
394 struct net_device *dev;
395 int err;
396
397 dev = alloc_arcdev(device);
398 if (!dev)
399 return -ENOMEM;
400
Linus Torvalds1da177e2005-04-16 15:20:36 -0700401 dev->base_addr = io;
402 dev->irq = irq;
403 if (dev->irq == 2)
404 dev->irq = 9;
405
406 err = com90io_probe(dev);
407
408 if (err) {
409 free_netdev(dev);
410 return err;
411 }
412
413 my_dev = dev;
414 return 0;
415}
416
417static void __exit com90io_exit(void)
418{
419 struct net_device *dev = my_dev;
420 int ioaddr = dev->base_addr;
421
422 unregister_netdev(dev);
423
424 /* Set the thing back to MMAP mode, in case the old driver is loaded later */
425 outb((inb(_CONFIG) & ~IOMAPflag), _CONFIG);
426
427 free_irq(dev->irq, dev);
428 release_region(dev->base_addr, ARCNET_TOTAL_SIZE);
429 free_netdev(dev);
430}
431
432module_init(com90io_init)
433module_exit(com90io_exit)