blob: f164ba4eba02292806cd04ece8864f7efb2f3570 [file] [log] [blame]
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001/*
2 * This file is subject to the terms and conditions of the GNU General Public
3 * License. See the file "COPYING" in the main directory of this archive
4 * for more details.
5 *
6 * Copyright (C) 2005 Silicon Graphics, Inc. All Rights Reserved.
7 */
8
9/*
10 * This file contains a module version of the ioc3 serial driver. This
11 * includes all the support functions needed (support functions, etc.)
12 * and the serial driver itself.
13 */
14#include <linux/errno.h>
15#include <linux/tty.h>
16#include <linux/serial.h>
17#include <linux/circ_buf.h>
18#include <linux/serial_reg.h>
19#include <linux/module.h>
20#include <linux/pci.h>
21#include <linux/serial_core.h>
22#include <linux/ioc3.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090023#include <linux/slab.h>
Patrick Gefre2d0cfb52006-01-14 13:20:40 -080024
25/*
26 * Interesting things about the ioc3
27 */
28
29#define LOGICAL_PORTS 2 /* rs232(0) and rs422(1) */
30#define PORTS_PER_CARD 2
31#define LOGICAL_PORTS_PER_CARD (PORTS_PER_CARD * LOGICAL_PORTS)
32#define MAX_CARDS 8
33#define MAX_LOGICAL_PORTS (LOGICAL_PORTS_PER_CARD * MAX_CARDS)
34
35/* determine given the sio_ir what port it applies to */
36#define GET_PORT_FROM_SIO_IR(_x) (_x & SIO_IR_SA) ? 0 : 1
37
38
39/*
40 * we have 2 logical ports (rs232, rs422) for each physical port
41 * evens are rs232, odds are rs422
42 */
43#define GET_PHYSICAL_PORT(_x) ((_x) >> 1)
44#define GET_LOGICAL_PORT(_x) ((_x) & 1)
45#define IS_PHYSICAL_PORT(_x) !((_x) & 1)
46#define IS_RS232(_x) !((_x) & 1)
47
48static unsigned int Num_of_ioc3_cards;
49static unsigned int Submodule_slot;
50
51/* defining this will get you LOTS of great debug info */
52//#define DEBUG_INTERRUPTS
53#define DPRINT_CONFIG(_x...) ;
54//#define DPRINT_CONFIG(_x...) printk _x
55#define NOT_PROGRESS() ;
Harvey Harrison71cc2c22008-04-30 00:55:10 -070056//#define NOT_PROGRESS() printk("%s : fails %d\n", __func__, __LINE__)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -080057
58/* number of characters we want to transmit to the lower level at a time */
59#define MAX_CHARS 256
60#define FIFO_SIZE (MAX_CHARS-1) /* it's a uchar */
61
62/* Device name we're using */
63#define DEVICE_NAME "ttySIOC"
64#define DEVICE_MAJOR 204
65#define DEVICE_MINOR 116
66
67/* flags for next_char_state */
68#define NCS_BREAK 0x1
69#define NCS_PARITY 0x2
70#define NCS_FRAMING 0x4
71#define NCS_OVERRUN 0x8
72
73/* cause we need SOME parameters ... */
74#define MIN_BAUD_SUPPORTED 1200
75#define MAX_BAUD_SUPPORTED 115200
76
77/* protocol types supported */
78#define PROTO_RS232 0
79#define PROTO_RS422 1
80
81/* Notification types */
82#define N_DATA_READY 0x01
83#define N_OUTPUT_LOWAT 0x02
84#define N_BREAK 0x04
85#define N_PARITY_ERROR 0x08
86#define N_FRAMING_ERROR 0x10
87#define N_OVERRUN_ERROR 0x20
88#define N_DDCD 0x40
89#define N_DCTS 0x80
90
91#define N_ALL_INPUT (N_DATA_READY | N_BREAK \
92 | N_PARITY_ERROR | N_FRAMING_ERROR \
93 | N_OVERRUN_ERROR | N_DDCD | N_DCTS)
94
95#define N_ALL_OUTPUT N_OUTPUT_LOWAT
96
97#define N_ALL_ERRORS (N_PARITY_ERROR | N_FRAMING_ERROR \
98 | N_OVERRUN_ERROR)
99
100#define N_ALL (N_DATA_READY | N_OUTPUT_LOWAT | N_BREAK \
101 | N_PARITY_ERROR | N_FRAMING_ERROR \
102 | N_OVERRUN_ERROR | N_DDCD | N_DCTS)
103
104#define SER_CLK_SPEED(prediv) ((22000000 << 1) / prediv)
105#define SER_DIVISOR(x, clk) (((clk) + (x) * 8) / ((x) * 16))
106#define DIVISOR_TO_BAUD(div, clk) ((clk) / 16 / (div))
107
108/* Some masks */
109#define LCR_MASK_BITS_CHAR (UART_LCR_WLEN5 | UART_LCR_WLEN6 \
110 | UART_LCR_WLEN7 | UART_LCR_WLEN8)
111#define LCR_MASK_STOP_BITS (UART_LCR_STOP)
112
113#define PENDING(_a, _p) (readl(&(_p)->vma->sio_ir) & (_a)->ic_enable)
114
115#define RING_BUF_SIZE 4096
116#define BUF_SIZE_BIT SBBR_L_SIZE
117#define PROD_CONS_MASK PROD_CONS_PTR_4K
118
119#define TOTAL_RING_BUF_SIZE (RING_BUF_SIZE * 4)
120
121/* driver specific - one per card */
122struct ioc3_card {
123 struct {
124 /* uart ports are allocated here */
125 struct uart_port icp_uart_port[LOGICAL_PORTS];
126 /* the ioc3_port used for this port */
127 struct ioc3_port *icp_port;
128 } ic_port[PORTS_PER_CARD];
129 /* currently enabled interrupts */
130 uint32_t ic_enable;
131};
132
133/* Local port info for each IOC3 serial port */
134struct ioc3_port {
135 /* handy reference material */
136 struct uart_port *ip_port;
137 struct ioc3_card *ip_card;
138 struct ioc3_driver_data *ip_idd;
139 struct ioc3_submodule *ip_is;
140
141 /* pci mem addresses for this port */
142 struct ioc3_serialregs __iomem *ip_serial_regs;
143 struct ioc3_uartregs __iomem *ip_uart_regs;
144
145 /* Ring buffer page for this port */
146 dma_addr_t ip_dma_ringbuf;
147 /* vaddr of ring buffer */
148 struct ring_buffer *ip_cpu_ringbuf;
149
150 /* Rings for this port */
151 struct ring *ip_inring;
152 struct ring *ip_outring;
153
154 /* Hook to port specific values */
155 struct port_hooks *ip_hooks;
156
157 spinlock_t ip_lock;
158
159 /* Various rx/tx parameters */
160 int ip_baud;
161 int ip_tx_lowat;
162 int ip_rx_timeout;
163
164 /* Copy of notification bits */
165 int ip_notify;
166
167 /* Shadow copies of various registers so we don't need to PIO
168 * read them constantly
169 */
170 uint32_t ip_sscr;
171 uint32_t ip_tx_prod;
172 uint32_t ip_rx_cons;
173 unsigned char ip_flags;
174};
175
176/* tx low water mark. We need to notify the driver whenever tx is getting
177 * close to empty so it can refill the tx buffer and keep things going.
178 * Let's assume that if we interrupt 1 ms before the tx goes idle, we'll
179 * have no trouble getting in more chars in time (I certainly hope so).
180 */
181#define TX_LOWAT_LATENCY 1000
182#define TX_LOWAT_HZ (1000000 / TX_LOWAT_LATENCY)
183#define TX_LOWAT_CHARS(baud) (baud / 10 / TX_LOWAT_HZ)
184
185/* Flags per port */
186#define INPUT_HIGH 0x01
187 /* used to signify that we have turned off the rx_high
188 * temporarily - we need to drain the fifo and don't
189 * want to get blasted with interrupts.
190 */
191#define DCD_ON 0x02
192 /* DCD state is on */
193#define LOWAT_WRITTEN 0x04
194#define READ_ABORTED 0x08
195 /* the read was aborted - used to avaoid infinate looping
196 * in the interrupt handler
197 */
198#define INPUT_ENABLE 0x10
199
200/* Since each port has different register offsets and bitmasks
201 * for everything, we'll store those that we need in tables so we
202 * don't have to be constantly checking the port we are dealing with.
203 */
204struct port_hooks {
205 uint32_t intr_delta_dcd;
206 uint32_t intr_delta_cts;
207 uint32_t intr_tx_mt;
208 uint32_t intr_rx_timer;
209 uint32_t intr_rx_high;
210 uint32_t intr_tx_explicit;
211 uint32_t intr_clear;
212 uint32_t intr_all;
213 char rs422_select_pin;
214};
215
216static struct port_hooks hooks_array[PORTS_PER_CARD] = {
217 /* values for port A */
218 {
219 .intr_delta_dcd = SIO_IR_SA_DELTA_DCD,
220 .intr_delta_cts = SIO_IR_SA_DELTA_CTS,
221 .intr_tx_mt = SIO_IR_SA_TX_MT,
222 .intr_rx_timer = SIO_IR_SA_RX_TIMER,
223 .intr_rx_high = SIO_IR_SA_RX_HIGH,
224 .intr_tx_explicit = SIO_IR_SA_TX_EXPLICIT,
225 .intr_clear = (SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL
226 | SIO_IR_SA_RX_HIGH
227 | SIO_IR_SA_RX_TIMER
228 | SIO_IR_SA_DELTA_DCD
229 | SIO_IR_SA_DELTA_CTS
230 | SIO_IR_SA_INT
231 | SIO_IR_SA_TX_EXPLICIT
232 | SIO_IR_SA_MEMERR),
233 .intr_all = SIO_IR_SA,
234 .rs422_select_pin = GPPR_UARTA_MODESEL_PIN,
235 },
236
237 /* values for port B */
238 {
239 .intr_delta_dcd = SIO_IR_SB_DELTA_DCD,
240 .intr_delta_cts = SIO_IR_SB_DELTA_CTS,
241 .intr_tx_mt = SIO_IR_SB_TX_MT,
242 .intr_rx_timer = SIO_IR_SB_RX_TIMER,
243 .intr_rx_high = SIO_IR_SB_RX_HIGH,
244 .intr_tx_explicit = SIO_IR_SB_TX_EXPLICIT,
245 .intr_clear = (SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL
246 | SIO_IR_SB_RX_HIGH
247 | SIO_IR_SB_RX_TIMER
248 | SIO_IR_SB_DELTA_DCD
249 | SIO_IR_SB_DELTA_CTS
250 | SIO_IR_SB_INT
251 | SIO_IR_SB_TX_EXPLICIT
252 | SIO_IR_SB_MEMERR),
253 .intr_all = SIO_IR_SB,
254 .rs422_select_pin = GPPR_UARTB_MODESEL_PIN,
255 }
256};
257
258struct ring_entry {
259 union {
260 struct {
261 uint32_t alldata;
262 uint32_t allsc;
263 } all;
264 struct {
265 char data[4]; /* data bytes */
266 char sc[4]; /* status/control */
267 } s;
268 } u;
269};
270
271/* Test the valid bits in any of the 4 sc chars using "allsc" member */
272#define RING_ANY_VALID \
273 ((uint32_t)(RXSB_MODEM_VALID | RXSB_DATA_VALID) * 0x01010101)
274
275#define ring_sc u.s.sc
276#define ring_data u.s.data
277#define ring_allsc u.all.allsc
278
279/* Number of entries per ring buffer. */
280#define ENTRIES_PER_RING (RING_BUF_SIZE / (int) sizeof(struct ring_entry))
281
282/* An individual ring */
283struct ring {
284 struct ring_entry entries[ENTRIES_PER_RING];
285};
286
287/* The whole enchilada */
288struct ring_buffer {
289 struct ring TX_A;
290 struct ring RX_A;
291 struct ring TX_B;
292 struct ring RX_B;
293};
294
295/* Get a ring from a port struct */
296#define RING(_p, _wh) &(((struct ring_buffer *)((_p)->ip_cpu_ringbuf))->_wh)
297
298/* for Infinite loop detection */
299#define MAXITER 10000000
300
301
302/**
303 * set_baud - Baud rate setting code
304 * @port: port to set
305 * @baud: baud rate to use
306 */
307static int set_baud(struct ioc3_port *port, int baud)
308{
309 int divisor;
310 int actual_baud;
311 int diff;
312 int lcr, prediv;
313 struct ioc3_uartregs __iomem *uart;
314
315 for (prediv = 6; prediv < 64; prediv++) {
316 divisor = SER_DIVISOR(baud, SER_CLK_SPEED(prediv));
317 if (!divisor)
318 continue; /* invalid divisor */
319 actual_baud = DIVISOR_TO_BAUD(divisor, SER_CLK_SPEED(prediv));
320
321 diff = actual_baud - baud;
322 if (diff < 0)
323 diff = -diff;
324
325 /* if we're within 1% we've found a match */
326 if (diff * 100 <= actual_baud)
327 break;
328 }
329
330 /* if the above loop completed, we didn't match
331 * the baud rate. give up.
332 */
333 if (prediv == 64) {
334 NOT_PROGRESS();
335 return 1;
336 }
337
338 uart = port->ip_uart_regs;
339 lcr = readb(&uart->iu_lcr);
340
341 writeb(lcr | UART_LCR_DLAB, &uart->iu_lcr);
342 writeb((unsigned char)divisor, &uart->iu_dll);
343 writeb((unsigned char)(divisor >> 8), &uart->iu_dlm);
344 writeb((unsigned char)prediv, &uart->iu_scr);
345 writeb((unsigned char)lcr, &uart->iu_lcr);
346
347 return 0;
348}
349
350/**
351 * get_ioc3_port - given a uart port, return the control structure
352 * @the_port: uart port to find
353 */
354static struct ioc3_port *get_ioc3_port(struct uart_port *the_port)
355{
356 struct ioc3_driver_data *idd = dev_get_drvdata(the_port->dev);
357 struct ioc3_card *card_ptr = idd->data[Submodule_slot];
358 int ii, jj;
359
360 if (!card_ptr) {
361 NOT_PROGRESS();
362 return NULL;
363 }
364 for (ii = 0; ii < PORTS_PER_CARD; ii++) {
365 for (jj = 0; jj < LOGICAL_PORTS; jj++) {
366 if (the_port == &card_ptr->ic_port[ii].icp_uart_port[jj])
367 return card_ptr->ic_port[ii].icp_port;
368 }
369 }
370 NOT_PROGRESS();
371 return NULL;
372}
373
374/**
375 * port_init - Initialize the sio and ioc3 hardware for a given port
376 * called per port from attach...
377 * @port: port to initialize
378 */
379static int inline port_init(struct ioc3_port *port)
380{
381 uint32_t sio_cr;
382 struct port_hooks *hooks = port->ip_hooks;
383 struct ioc3_uartregs __iomem *uart;
384 int reset_loop_counter = 0xfffff;
385 struct ioc3_driver_data *idd = port->ip_idd;
386
387 /* Idle the IOC3 serial interface */
388 writel(SSCR_RESET, &port->ip_serial_regs->sscr);
389
390 /* Wait until any pending bus activity for this port has ceased */
391 do {
392 sio_cr = readl(&idd->vma->sio_cr);
393 if (reset_loop_counter-- <= 0) {
394 printk(KERN_WARNING
395 "IOC3 unable to come out of reset"
396 " scr 0x%x\n", sio_cr);
397 return -1;
398 }
399 } while (!(sio_cr & SIO_CR_ARB_DIAG_IDLE) &&
400 (((sio_cr &= SIO_CR_ARB_DIAG) == SIO_CR_ARB_DIAG_TXA)
401 || sio_cr == SIO_CR_ARB_DIAG_TXB
402 || sio_cr == SIO_CR_ARB_DIAG_RXA
403 || sio_cr == SIO_CR_ARB_DIAG_RXB));
404
405 /* Finish reset sequence */
406 writel(0, &port->ip_serial_regs->sscr);
407
408 /* Once RESET is done, reload cached tx_prod and rx_cons values
409 * and set rings to empty by making prod == cons
410 */
411 port->ip_tx_prod = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
412 writel(port->ip_tx_prod, &port->ip_serial_regs->stpir);
413 port->ip_rx_cons = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
414 writel(port->ip_rx_cons | SRCIR_ARM, &port->ip_serial_regs->srcir);
415
416 /* Disable interrupts for this 16550 */
417 uart = port->ip_uart_regs;
418 writeb(0, &uart->iu_lcr);
419 writeb(0, &uart->iu_ier);
420
421 /* Set the default baud */
422 set_baud(port, port->ip_baud);
423
424 /* Set line control to 8 bits no parity */
425 writeb(UART_LCR_WLEN8 | 0, &uart->iu_lcr);
426 /* UART_LCR_STOP == 1 stop */
427
428 /* Enable the FIFOs */
429 writeb(UART_FCR_ENABLE_FIFO, &uart->iu_fcr);
430 /* then reset 16550 FIFOs */
431 writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
432 &uart->iu_fcr);
433
434 /* Clear modem control register */
435 writeb(0, &uart->iu_mcr);
436
437 /* Clear deltas in modem status register */
438 writel(0, &port->ip_serial_regs->shadow);
439
440 /* Only do this once per port pair */
441 if (port->ip_hooks == &hooks_array[0]) {
442 unsigned long ring_pci_addr;
443 uint32_t __iomem *sbbr_l, *sbbr_h;
444
445 sbbr_l = &idd->vma->sbbr_l;
446 sbbr_h = &idd->vma->sbbr_h;
447 ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf;
448 DPRINT_CONFIG(("%s: ring_pci_addr 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700449 __func__, (void *)ring_pci_addr));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800450
451 writel((unsigned int)((uint64_t) ring_pci_addr >> 32), sbbr_h);
452 writel((unsigned int)ring_pci_addr | BUF_SIZE_BIT, sbbr_l);
453 }
454
455 /* Set the receive timeout value to 10 msec */
456 writel(SRTR_HZ / 100, &port->ip_serial_regs->srtr);
457
458 /* Set rx threshold, enable DMA */
459 /* Set high water mark at 3/4 of full ring */
460 port->ip_sscr = (ENTRIES_PER_RING * 3 / 4);
461
462 /* uart experiences pauses at high baud rate reducing actual
463 * throughput by 10% or so unless we enable high speed polling
464 * XXX when this hardware bug is resolved we should revert to
465 * normal polling speed
466 */
467 port->ip_sscr |= SSCR_HIGH_SPD;
468
469 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
470
471 /* Disable and clear all serial related interrupt bits */
472 port->ip_card->ic_enable &= ~hooks->intr_clear;
473 ioc3_disable(port->ip_is, idd, hooks->intr_clear);
474 ioc3_ack(port->ip_is, idd, hooks->intr_clear);
475 return 0;
476}
477
478/**
479 * enable_intrs - enable interrupts
480 * @port: port to enable
481 * @mask: mask to use
482 */
483static void enable_intrs(struct ioc3_port *port, uint32_t mask)
484{
485 if ((port->ip_card->ic_enable & mask) != mask) {
486 port->ip_card->ic_enable |= mask;
487 ioc3_enable(port->ip_is, port->ip_idd, mask);
488 }
489}
490
491/**
492 * local_open - local open a port
493 * @port: port to open
494 */
495static inline int local_open(struct ioc3_port *port)
496{
497 int spiniter = 0;
498
499 port->ip_flags = INPUT_ENABLE;
500
501 /* Pause the DMA interface if necessary */
502 if (port->ip_sscr & SSCR_DMA_EN) {
503 writel(port->ip_sscr | SSCR_DMA_PAUSE,
504 &port->ip_serial_regs->sscr);
505 while ((readl(&port->ip_serial_regs->sscr)
506 & SSCR_PAUSE_STATE) == 0) {
507 spiniter++;
508 if (spiniter > MAXITER) {
509 NOT_PROGRESS();
510 return -1;
511 }
512 }
513 }
514
515 /* Reset the input fifo. If the uart received chars while the port
516 * was closed and DMA is not enabled, the uart may have a bunch of
517 * chars hanging around in its rx fifo which will not be discarded
518 * by rclr in the upper layer. We must get rid of them here.
519 */
520 writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR,
521 &port->ip_uart_regs->iu_fcr);
522
523 writeb(UART_LCR_WLEN8, &port->ip_uart_regs->iu_lcr);
524 /* UART_LCR_STOP == 1 stop */
525
526 /* Re-enable DMA, set default threshold to intr whenever there is
527 * data available.
528 */
529 port->ip_sscr &= ~SSCR_RX_THRESHOLD;
530 port->ip_sscr |= 1; /* default threshold */
531
532 /* Plug in the new sscr. This implicitly clears the DMA_PAUSE
533 * flag if it was set above
534 */
535 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
536 port->ip_tx_lowat = 1;
537 return 0;
538}
539
540/**
541 * set_rx_timeout - Set rx timeout and threshold values.
542 * @port: port to use
543 * @timeout: timeout value in ticks
544 */
545static inline int set_rx_timeout(struct ioc3_port *port, int timeout)
546{
547 int threshold;
548
549 port->ip_rx_timeout = timeout;
550
551 /* Timeout is in ticks. Let's figure out how many chars we
552 * can receive at the current baud rate in that interval
553 * and set the rx threshold to that amount. There are 4 chars
554 * per ring entry, so we'll divide the number of chars that will
555 * arrive in timeout by 4.
556 * So .... timeout * baud / 10 / HZ / 4, with HZ = 100.
557 */
558 threshold = timeout * port->ip_baud / 4000;
559 if (threshold == 0)
560 threshold = 1; /* otherwise we'll intr all the time! */
561
562 if ((unsigned)threshold > (unsigned)SSCR_RX_THRESHOLD)
563 return 1;
564
565 port->ip_sscr &= ~SSCR_RX_THRESHOLD;
566 port->ip_sscr |= threshold;
567 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
568
569 /* Now set the rx timeout to the given value
570 * again timeout * SRTR_HZ / HZ
571 */
572 timeout = timeout * SRTR_HZ / 100;
573 if (timeout > SRTR_CNT)
574 timeout = SRTR_CNT;
575 writel(timeout, &port->ip_serial_regs->srtr);
576 return 0;
577}
578
579/**
580 * config_port - config the hardware
581 * @port: port to config
582 * @baud: baud rate for the port
583 * @byte_size: data size
584 * @stop_bits: number of stop bits
585 * @parenb: parity enable ?
586 * @parodd: odd parity ?
587 */
588static inline int
589config_port(struct ioc3_port *port,
590 int baud, int byte_size, int stop_bits, int parenb, int parodd)
591{
592 char lcr, sizebits;
593 int spiniter = 0;
594
595 DPRINT_CONFIG(("%s: line %d baud %d byte_size %d stop %d parenb %d "
596 "parodd %d\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700597 __func__, ((struct uart_port *)port->ip_port)->line,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800598 baud, byte_size, stop_bits, parenb, parodd));
599
600 if (set_baud(port, baud))
601 return 1;
602
603 switch (byte_size) {
604 case 5:
605 sizebits = UART_LCR_WLEN5;
606 break;
607 case 6:
608 sizebits = UART_LCR_WLEN6;
609 break;
610 case 7:
611 sizebits = UART_LCR_WLEN7;
612 break;
613 case 8:
614 sizebits = UART_LCR_WLEN8;
615 break;
616 default:
617 return 1;
618 }
619
620 /* Pause the DMA interface if necessary */
621 if (port->ip_sscr & SSCR_DMA_EN) {
622 writel(port->ip_sscr | SSCR_DMA_PAUSE,
623 &port->ip_serial_regs->sscr);
624 while ((readl(&port->ip_serial_regs->sscr)
625 & SSCR_PAUSE_STATE) == 0) {
626 spiniter++;
627 if (spiniter > MAXITER)
628 return -1;
629 }
630 }
631
632 /* Clear relevant fields in lcr */
633 lcr = readb(&port->ip_uart_regs->iu_lcr);
634 lcr &= ~(LCR_MASK_BITS_CHAR | UART_LCR_EPAR |
635 UART_LCR_PARITY | LCR_MASK_STOP_BITS);
636
637 /* Set byte size in lcr */
638 lcr |= sizebits;
639
640 /* Set parity */
641 if (parenb) {
642 lcr |= UART_LCR_PARITY;
643 if (!parodd)
644 lcr |= UART_LCR_EPAR;
645 }
646
647 /* Set stop bits */
648 if (stop_bits)
649 lcr |= UART_LCR_STOP /* 2 stop bits */ ;
650
651 writeb(lcr, &port->ip_uart_regs->iu_lcr);
652
653 /* Re-enable the DMA interface if necessary */
654 if (port->ip_sscr & SSCR_DMA_EN) {
655 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
656 }
657 port->ip_baud = baud;
658
659 /* When we get within this number of ring entries of filling the
660 * entire ring on tx, place an EXPLICIT intr to generate a lowat
661 * notification when output has drained.
662 */
663 port->ip_tx_lowat = (TX_LOWAT_CHARS(baud) + 3) / 4;
664 if (port->ip_tx_lowat == 0)
665 port->ip_tx_lowat = 1;
666
667 set_rx_timeout(port, 2);
668 return 0;
669}
670
671/**
672 * do_write - Write bytes to the port. Returns the number of bytes
673 * actually written. Called from transmit_chars
674 * @port: port to use
675 * @buf: the stuff to write
676 * @len: how many bytes in 'buf'
677 */
678static inline int do_write(struct ioc3_port *port, char *buf, int len)
679{
680 int prod_ptr, cons_ptr, total = 0;
681 struct ring *outring;
682 struct ring_entry *entry;
683 struct port_hooks *hooks = port->ip_hooks;
684
685 BUG_ON(!(len >= 0));
686
687 prod_ptr = port->ip_tx_prod;
688 cons_ptr = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
689 outring = port->ip_outring;
690
691 /* Maintain a 1-entry red-zone. The ring buffer is full when
692 * (cons - prod) % ring_size is 1. Rather than do this subtraction
693 * in the body of the loop, I'll do it now.
694 */
695 cons_ptr = (cons_ptr - (int)sizeof(struct ring_entry)) & PROD_CONS_MASK;
696
697 /* Stuff the bytes into the output */
698 while ((prod_ptr != cons_ptr) && (len > 0)) {
699 int xx;
700
701 /* Get 4 bytes (one ring entry) at a time */
702 entry = (struct ring_entry *)((caddr_t) outring + prod_ptr);
703
704 /* Invalidate all entries */
705 entry->ring_allsc = 0;
706
707 /* Copy in some bytes */
708 for (xx = 0; (xx < 4) && (len > 0); xx++) {
709 entry->ring_data[xx] = *buf++;
710 entry->ring_sc[xx] = TXCB_VALID;
711 len--;
712 total++;
713 }
714
715 /* If we are within some small threshold of filling up the
716 * entire ring buffer, we must place an EXPLICIT intr here
717 * to generate a lowat interrupt in case we subsequently
718 * really do fill up the ring and the caller goes to sleep.
719 * No need to place more than one though.
720 */
721 if (!(port->ip_flags & LOWAT_WRITTEN) &&
722 ((cons_ptr - prod_ptr) & PROD_CONS_MASK)
723 <= port->ip_tx_lowat * (int)sizeof(struct ring_entry)) {
724 port->ip_flags |= LOWAT_WRITTEN;
725 entry->ring_sc[0] |= TXCB_INT_WHEN_DONE;
726 }
727
728 /* Go on to next entry */
729 prod_ptr += sizeof(struct ring_entry);
730 prod_ptr &= PROD_CONS_MASK;
731 }
732
733 /* If we sent something, start DMA if necessary */
734 if (total > 0 && !(port->ip_sscr & SSCR_DMA_EN)) {
735 port->ip_sscr |= SSCR_DMA_EN;
736 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
737 }
738
739 /* Store the new producer pointer. If tx is disabled, we stuff the
740 * data into the ring buffer, but we don't actually start tx.
741 */
742 if (!uart_tx_stopped(port->ip_port)) {
743 writel(prod_ptr, &port->ip_serial_regs->stpir);
744
745 /* If we are now transmitting, enable tx_mt interrupt so we
746 * can disable DMA if necessary when the tx finishes.
747 */
748 if (total > 0)
749 enable_intrs(port, hooks->intr_tx_mt);
750 }
751 port->ip_tx_prod = prod_ptr;
752
753 return total;
754}
755
756/**
757 * disable_intrs - disable interrupts
758 * @port: port to enable
759 * @mask: mask to use
760 */
761static inline void disable_intrs(struct ioc3_port *port, uint32_t mask)
762{
763 if (port->ip_card->ic_enable & mask) {
764 ioc3_disable(port->ip_is, port->ip_idd, mask);
765 port->ip_card->ic_enable &= ~mask;
766 }
767}
768
769/**
770 * set_notification - Modify event notification
771 * @port: port to use
772 * @mask: events mask
773 * @set_on: set ?
774 */
775static int set_notification(struct ioc3_port *port, int mask, int set_on)
776{
777 struct port_hooks *hooks = port->ip_hooks;
778 uint32_t intrbits, sscrbits;
779
780 BUG_ON(!mask);
781
782 intrbits = sscrbits = 0;
783
784 if (mask & N_DATA_READY)
785 intrbits |= (hooks->intr_rx_timer | hooks->intr_rx_high);
786 if (mask & N_OUTPUT_LOWAT)
787 intrbits |= hooks->intr_tx_explicit;
788 if (mask & N_DDCD) {
789 intrbits |= hooks->intr_delta_dcd;
790 sscrbits |= SSCR_RX_RING_DCD;
791 }
792 if (mask & N_DCTS)
793 intrbits |= hooks->intr_delta_cts;
794
795 if (set_on) {
796 enable_intrs(port, intrbits);
797 port->ip_notify |= mask;
798 port->ip_sscr |= sscrbits;
799 } else {
800 disable_intrs(port, intrbits);
801 port->ip_notify &= ~mask;
802 port->ip_sscr &= ~sscrbits;
803 }
804
805 /* We require DMA if either DATA_READY or DDCD notification is
806 * currently requested. If neither of these is requested and
807 * there is currently no tx in progress, DMA may be disabled.
808 */
809 if (port->ip_notify & (N_DATA_READY | N_DDCD))
810 port->ip_sscr |= SSCR_DMA_EN;
811 else if (!(port->ip_card->ic_enable & hooks->intr_tx_mt))
812 port->ip_sscr &= ~SSCR_DMA_EN;
813
814 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
815 return 0;
816}
817
818/**
819 * set_mcr - set the master control reg
820 * @the_port: port to use
821 * @mask1: mcr mask
822 * @mask2: shadow mask
823 */
824static inline int set_mcr(struct uart_port *the_port,
825 int mask1, int mask2)
826{
827 struct ioc3_port *port = get_ioc3_port(the_port);
828 uint32_t shadow;
829 int spiniter = 0;
830 char mcr;
831
832 if (!port)
833 return -1;
834
835 /* Pause the DMA interface if necessary */
836 if (port->ip_sscr & SSCR_DMA_EN) {
837 writel(port->ip_sscr | SSCR_DMA_PAUSE,
838 &port->ip_serial_regs->sscr);
839 while ((readl(&port->ip_serial_regs->sscr)
840 & SSCR_PAUSE_STATE) == 0) {
841 spiniter++;
842 if (spiniter > MAXITER)
843 return -1;
844 }
845 }
846 shadow = readl(&port->ip_serial_regs->shadow);
847 mcr = (shadow & 0xff000000) >> 24;
848
849 /* Set new value */
850 mcr |= mask1;
851 shadow |= mask2;
852 writeb(mcr, &port->ip_uart_regs->iu_mcr);
853 writel(shadow, &port->ip_serial_regs->shadow);
854
855 /* Re-enable the DMA interface if necessary */
856 if (port->ip_sscr & SSCR_DMA_EN) {
857 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
858 }
859 return 0;
860}
861
862/**
863 * ioc3_set_proto - set the protocol for the port
864 * @port: port to use
865 * @proto: protocol to use
866 */
867static int ioc3_set_proto(struct ioc3_port *port, int proto)
868{
869 struct port_hooks *hooks = port->ip_hooks;
870
871 switch (proto) {
872 default:
873 case PROTO_RS232:
874 /* Clear the appropriate GIO pin */
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700875 DPRINT_CONFIG(("%s: rs232\n", __func__));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800876 writel(0, (&port->ip_idd->vma->gppr[0]
877 + hooks->rs422_select_pin));
878 break;
879
880 case PROTO_RS422:
881 /* Set the appropriate GIO pin */
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700882 DPRINT_CONFIG(("%s: rs422\n", __func__));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800883 writel(1, (&port->ip_idd->vma->gppr[0]
884 + hooks->rs422_select_pin));
885 break;
886 }
887 return 0;
888}
889
890/**
891 * transmit_chars - upper level write, called with the_port->lock
892 * @the_port: port to write
893 */
894static void transmit_chars(struct uart_port *the_port)
895{
896 int xmit_count, tail, head;
897 int result;
898 char *start;
899 struct tty_struct *tty;
900 struct ioc3_port *port = get_ioc3_port(the_port);
Alan Coxebd2c8f2009-09-19 13:13:28 -0700901 struct uart_state *state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800902
903 if (!the_port)
904 return;
905 if (!port)
906 return;
907
Alan Coxebd2c8f2009-09-19 13:13:28 -0700908 state = the_port->state;
909 tty = state->port.tty;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800910
Alan Coxebd2c8f2009-09-19 13:13:28 -0700911 if (uart_circ_empty(&state->xmit) || uart_tx_stopped(the_port)) {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800912 /* Nothing to do or hw stopped */
913 set_notification(port, N_ALL_OUTPUT, 0);
914 return;
915 }
916
Alan Coxebd2c8f2009-09-19 13:13:28 -0700917 head = state->xmit.head;
918 tail = state->xmit.tail;
919 start = (char *)&state->xmit.buf[tail];
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800920
921 /* write out all the data or until the end of the buffer */
922 xmit_count = (head < tail) ? (UART_XMIT_SIZE - tail) : (head - tail);
923 if (xmit_count > 0) {
924 result = do_write(port, start, xmit_count);
925 if (result > 0) {
926 /* booking */
927 xmit_count -= result;
928 the_port->icount.tx += result;
929 /* advance the pointers */
930 tail += result;
931 tail &= UART_XMIT_SIZE - 1;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700932 state->xmit.tail = tail;
933 start = (char *)&state->xmit.buf[tail];
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800934 }
935 }
Alan Coxebd2c8f2009-09-19 13:13:28 -0700936 if (uart_circ_chars_pending(&state->xmit) < WAKEUP_CHARS)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800937 uart_write_wakeup(the_port);
938
Alan Coxebd2c8f2009-09-19 13:13:28 -0700939 if (uart_circ_empty(&state->xmit)) {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800940 set_notification(port, N_OUTPUT_LOWAT, 0);
941 } else {
942 set_notification(port, N_OUTPUT_LOWAT, 1);
943 }
944}
945
946/**
947 * ioc3_change_speed - change the speed of the port
948 * @the_port: port to change
949 * @new_termios: new termios settings
950 * @old_termios: old termios settings
951 */
952static void
953ioc3_change_speed(struct uart_port *the_port,
Alan Cox606d0992006-12-08 02:38:45 -0800954 struct ktermios *new_termios, struct ktermios *old_termios)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800955{
956 struct ioc3_port *port = get_ioc3_port(the_port);
957 unsigned int cflag;
958 int baud;
959 int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700960 struct uart_state *state = the_port->state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800961
962 cflag = new_termios->c_cflag;
963
964 switch (cflag & CSIZE) {
965 case CS5:
966 new_data = 5;
967 break;
968 case CS6:
969 new_data = 6;
970 break;
971 case CS7:
972 new_data = 7;
973 break;
974 case CS8:
975 new_data = 8;
976 break;
977 default:
978 /* cuz we always need a default ... */
979 new_data = 5;
980 break;
981 }
982 if (cflag & CSTOPB) {
983 new_stop = 1;
984 }
985 if (cflag & PARENB) {
986 new_parity_enable = 1;
987 if (cflag & PARODD)
988 new_parity = 1;
989 }
990 baud = uart_get_baud_rate(the_port, new_termios, old_termios,
991 MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED);
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700992 DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __func__, baud,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800993 the_port->line));
994
995 if (!the_port->fifosize)
996 the_port->fifosize = FIFO_SIZE;
997 uart_update_timeout(the_port, cflag, baud);
998
999 the_port->ignore_status_mask = N_ALL_INPUT;
1000
Alan Coxebd2c8f2009-09-19 13:13:28 -07001001 state->port.tty->low_latency = 1;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001002
Alan Coxebd2c8f2009-09-19 13:13:28 -07001003 if (I_IGNPAR(state->port.tty))
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001004 the_port->ignore_status_mask &= ~(N_PARITY_ERROR
1005 | N_FRAMING_ERROR);
Alan Coxebd2c8f2009-09-19 13:13:28 -07001006 if (I_IGNBRK(state->port.tty)) {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001007 the_port->ignore_status_mask &= ~N_BREAK;
Alan Coxebd2c8f2009-09-19 13:13:28 -07001008 if (I_IGNPAR(state->port.tty))
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001009 the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
1010 }
1011 if (!(cflag & CREAD)) {
1012 /* ignore everything */
1013 the_port->ignore_status_mask &= ~N_DATA_READY;
1014 }
1015
1016 if (cflag & CRTSCTS) {
1017 /* enable hardware flow control */
1018 port->ip_sscr |= SSCR_HFC_EN;
1019 }
1020 else {
1021 /* disable hardware flow control */
1022 port->ip_sscr &= ~SSCR_HFC_EN;
1023 }
1024 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
1025
1026 /* Set the configuration and proper notification call */
1027 DPRINT_CONFIG(("%s : port 0x%p line %d cflag 0%o "
1028 "config_port(baud %d data %d stop %d penable %d "
1029 " parity %d), notification 0x%x\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001030 __func__, (void *)port, the_port->line, cflag, baud,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001031 new_data, new_stop, new_parity_enable, new_parity,
1032 the_port->ignore_status_mask));
1033
1034 if ((config_port(port, baud, /* baud */
1035 new_data, /* byte size */
1036 new_stop, /* stop bits */
1037 new_parity_enable, /* set parity */
1038 new_parity)) >= 0) { /* parity 1==odd */
1039 set_notification(port, the_port->ignore_status_mask, 1);
1040 }
1041}
1042
1043/**
1044 * ic3_startup_local - Start up the serial port - returns >= 0 if no errors
1045 * @the_port: Port to operate on
1046 */
1047static inline int ic3_startup_local(struct uart_port *the_port)
1048{
1049 struct ioc3_port *port;
1050
1051 if (!the_port) {
1052 NOT_PROGRESS();
1053 return -1;
1054 }
1055
1056 port = get_ioc3_port(the_port);
1057 if (!port) {
1058 NOT_PROGRESS();
1059 return -1;
1060 }
1061
1062 local_open(port);
1063
1064 /* set the protocol */
1065 ioc3_set_proto(port, IS_RS232(the_port->line) ? PROTO_RS232 :
1066 PROTO_RS422);
1067 return 0;
1068}
1069
1070/*
1071 * ioc3_cb_output_lowat - called when the output low water mark is hit
1072 * @port: port to output
1073 */
1074static void ioc3_cb_output_lowat(struct ioc3_port *port)
1075{
1076 unsigned long pflags;
1077
1078 /* the_port->lock is set on the call here */
1079 if (port->ip_port) {
1080 spin_lock_irqsave(&port->ip_port->lock, pflags);
1081 transmit_chars(port->ip_port);
1082 spin_unlock_irqrestore(&port->ip_port->lock, pflags);
1083 }
1084}
1085
1086/*
1087 * ioc3_cb_post_ncs - called for some basic errors
1088 * @port: port to use
1089 * @ncs: event
1090 */
1091static void ioc3_cb_post_ncs(struct uart_port *the_port, int ncs)
1092{
1093 struct uart_icount *icount;
1094
1095 icount = &the_port->icount;
1096
1097 if (ncs & NCS_BREAK)
1098 icount->brk++;
1099 if (ncs & NCS_FRAMING)
1100 icount->frame++;
1101 if (ncs & NCS_OVERRUN)
1102 icount->overrun++;
1103 if (ncs & NCS_PARITY)
1104 icount->parity++;
1105}
1106
1107/**
1108 * do_read - Read in bytes from the port. Return the number of bytes
1109 * actually read.
1110 * @the_port: port to use
1111 * @buf: place to put the stuff we read
1112 * @len: how big 'buf' is
1113 */
1114
1115static inline int do_read(struct uart_port *the_port, char *buf, int len)
1116{
1117 int prod_ptr, cons_ptr, total;
1118 struct ioc3_port *port = get_ioc3_port(the_port);
1119 struct ring *inring;
1120 struct ring_entry *entry;
1121 struct port_hooks *hooks = port->ip_hooks;
1122 int byte_num;
1123 char *sc;
1124 int loop_counter;
1125
1126 BUG_ON(!(len >= 0));
1127 BUG_ON(!port);
1128
1129 /* There is a nasty timing issue in the IOC3. When the rx_timer
1130 * expires or the rx_high condition arises, we take an interrupt.
1131 * At some point while servicing the interrupt, we read bytes from
1132 * the ring buffer and re-arm the rx_timer. However the rx_timer is
1133 * not started until the first byte is received *after* it is armed,
1134 * and any bytes pending in the rx construction buffers are not drained
1135 * to memory until either there are 4 bytes available or the rx_timer
1136 * expires. This leads to a potential situation where data is left
1137 * in the construction buffers forever - 1 to 3 bytes were received
1138 * after the interrupt was generated but before the rx_timer was
1139 * re-armed. At that point as long as no subsequent bytes are received
1140 * the timer will never be started and the bytes will remain in the
1141 * construction buffer forever. The solution is to execute a DRAIN
1142 * command after rearming the timer. This way any bytes received before
1143 * the DRAIN will be drained to memory, and any bytes received after
1144 * the DRAIN will start the TIMER and be drained when it expires.
1145 * Luckily, this only needs to be done when the DMA buffer is empty
1146 * since there is no requirement that this function return all
1147 * available data as long as it returns some.
1148 */
1149 /* Re-arm the timer */
1150
1151 writel(port->ip_rx_cons | SRCIR_ARM, &port->ip_serial_regs->srcir);
1152
1153 prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
1154 cons_ptr = port->ip_rx_cons;
1155
1156 if (prod_ptr == cons_ptr) {
1157 int reset_dma = 0;
1158
1159 /* Input buffer appears empty, do a flush. */
1160
1161 /* DMA must be enabled for this to work. */
1162 if (!(port->ip_sscr & SSCR_DMA_EN)) {
1163 port->ip_sscr |= SSCR_DMA_EN;
1164 reset_dma = 1;
1165 }
1166
1167 /* Potential race condition: we must reload the srpir after
1168 * issuing the drain command, otherwise we could think the rx
1169 * buffer is empty, then take a very long interrupt, and when
1170 * we come back it's full and we wait forever for the drain to
1171 * complete.
1172 */
1173 writel(port->ip_sscr | SSCR_RX_DRAIN,
1174 &port->ip_serial_regs->sscr);
1175 prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
1176
1177 /* We must not wait for the DRAIN to complete unless there are
1178 * at least 8 bytes (2 ring entries) available to receive the
1179 * data otherwise the DRAIN will never complete and we'll
1180 * deadlock here.
1181 * In fact, to make things easier, I'll just ignore the flush if
1182 * there is any data at all now available.
1183 */
1184 if (prod_ptr == cons_ptr) {
1185 loop_counter = 0;
1186 while (readl(&port->ip_serial_regs->sscr) &
1187 SSCR_RX_DRAIN) {
1188 loop_counter++;
1189 if (loop_counter > MAXITER)
1190 return -1;
1191 }
1192
1193 /* SIGH. We have to reload the prod_ptr *again* since
1194 * the drain may have caused it to change
1195 */
1196 prod_ptr = readl(&port->ip_serial_regs->srpir)
1197 & PROD_CONS_MASK;
1198 }
1199 if (reset_dma) {
1200 port->ip_sscr &= ~SSCR_DMA_EN;
1201 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
1202 }
1203 }
1204 inring = port->ip_inring;
1205 port->ip_flags &= ~READ_ABORTED;
1206
1207 total = 0;
1208 loop_counter = 0xfffff; /* to avoid hangs */
1209
1210 /* Grab bytes from the hardware */
1211 while ((prod_ptr != cons_ptr) && (len > 0)) {
1212 entry = (struct ring_entry *)((caddr_t) inring + cons_ptr);
1213
1214 if (loop_counter-- <= 0) {
1215 printk(KERN_WARNING "IOC3 serial: "
1216 "possible hang condition/"
1217 "port stuck on read (line %d).\n",
1218 the_port->line);
1219 break;
1220 }
1221
1222 /* According to the producer pointer, this ring entry
1223 * must contain some data. But if the PIO happened faster
1224 * than the DMA, the data may not be available yet, so let's
1225 * wait until it arrives.
1226 */
1227 if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
1228 /* Indicate the read is aborted so we don't disable
1229 * the interrupt thinking that the consumer is
1230 * congested.
1231 */
1232 port->ip_flags |= READ_ABORTED;
1233 len = 0;
1234 break;
1235 }
1236
1237 /* Load the bytes/status out of the ring entry */
1238 for (byte_num = 0; byte_num < 4 && len > 0; byte_num++) {
1239 sc = &(entry->ring_sc[byte_num]);
1240
1241 /* Check for change in modem state or overrun */
1242 if ((*sc & RXSB_MODEM_VALID)
1243 && (port->ip_notify & N_DDCD)) {
1244 /* Notify upper layer if DCD dropped */
1245 if ((port->ip_flags & DCD_ON)
1246 && !(*sc & RXSB_DCD)) {
1247 /* If we have already copied some data,
1248 * return it. We'll pick up the carrier
1249 * drop on the next pass. That way we
1250 * don't throw away the data that has
1251 * already been copied back to
1252 * the caller's buffer.
1253 */
1254 if (total > 0) {
1255 len = 0;
1256 break;
1257 }
1258 port->ip_flags &= ~DCD_ON;
1259
1260 /* Turn off this notification so the
1261 * carrier drop protocol won't see it
1262 * again when it does a read.
1263 */
1264 *sc &= ~RXSB_MODEM_VALID;
1265
1266 /* To keep things consistent, we need
1267 * to update the consumer pointer so
1268 * the next reader won't come in and
1269 * try to read the same ring entries
1270 * again. This must be done here before
1271 * the dcd change.
1272 */
1273
1274 if ((entry->ring_allsc & RING_ANY_VALID)
1275 == 0) {
1276 cons_ptr += (int)sizeof
1277 (struct ring_entry);
1278 cons_ptr &= PROD_CONS_MASK;
1279 }
1280 writel(cons_ptr,
1281 &port->ip_serial_regs->srcir);
1282 port->ip_rx_cons = cons_ptr;
1283
1284 /* Notify upper layer of carrier drop */
1285 if ((port->ip_notify & N_DDCD)
1286 && port->ip_port) {
1287 uart_handle_dcd_change
1288 (port->ip_port, 0);
1289 wake_up_interruptible
Alan Coxebd2c8f2009-09-19 13:13:28 -07001290 (&the_port->state->
Alan Coxbdc04e32009-09-19 13:13:31 -07001291 port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001292 }
1293
1294 /* If we had any data to return, we
1295 * would have returned it above.
1296 */
1297 return 0;
1298 }
1299 }
1300 if (*sc & RXSB_MODEM_VALID) {
1301 /* Notify that an input overrun occurred */
1302 if ((*sc & RXSB_OVERRUN)
1303 && (port->ip_notify & N_OVERRUN_ERROR)) {
1304 ioc3_cb_post_ncs(the_port, NCS_OVERRUN);
1305 }
1306 /* Don't look at this byte again */
1307 *sc &= ~RXSB_MODEM_VALID;
1308 }
1309
1310 /* Check for valid data or RX errors */
1311 if ((*sc & RXSB_DATA_VALID) &&
1312 ((*sc & (RXSB_PAR_ERR
1313 | RXSB_FRAME_ERR | RXSB_BREAK))
1314 && (port->ip_notify & (N_PARITY_ERROR
1315 | N_FRAMING_ERROR
1316 | N_BREAK)))) {
1317 /* There is an error condition on the next byte.
1318 * If we have already transferred some bytes,
1319 * we'll stop here. Otherwise if this is the
1320 * first byte to be read, we'll just transfer
1321 * it alone after notifying the
1322 * upper layer of its status.
1323 */
1324 if (total > 0) {
1325 len = 0;
1326 break;
1327 } else {
1328 if ((*sc & RXSB_PAR_ERR) &&
1329 (port->
1330 ip_notify & N_PARITY_ERROR)) {
1331 ioc3_cb_post_ncs(the_port,
1332 NCS_PARITY);
1333 }
1334 if ((*sc & RXSB_FRAME_ERR) &&
1335 (port->
1336 ip_notify & N_FRAMING_ERROR)) {
1337 ioc3_cb_post_ncs(the_port,
1338 NCS_FRAMING);
1339 }
1340 if ((*sc & RXSB_BREAK)
1341 && (port->ip_notify & N_BREAK)) {
1342 ioc3_cb_post_ncs
1343 (the_port, NCS_BREAK);
1344 }
1345 len = 1;
1346 }
1347 }
1348 if (*sc & RXSB_DATA_VALID) {
1349 *sc &= ~RXSB_DATA_VALID;
1350 *buf = entry->ring_data[byte_num];
1351 buf++;
1352 len--;
1353 total++;
1354 }
1355 }
1356
1357 /* If we used up this entry entirely, go on to the next one,
1358 * otherwise we must have run out of buffer space, so
1359 * leave the consumer pointer here for the next read in case
1360 * there are still unread bytes in this entry.
1361 */
1362 if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
1363 cons_ptr += (int)sizeof(struct ring_entry);
1364 cons_ptr &= PROD_CONS_MASK;
1365 }
1366 }
1367
1368 /* Update consumer pointer and re-arm rx timer interrupt */
1369 writel(cons_ptr, &port->ip_serial_regs->srcir);
1370 port->ip_rx_cons = cons_ptr;
1371
1372 /* If we have now dipped below the rx high water mark and we have
1373 * rx_high interrupt turned off, we can now turn it back on again.
1374 */
1375 if ((port->ip_flags & INPUT_HIGH) && (((prod_ptr - cons_ptr)
1376 & PROD_CONS_MASK) <
1377 ((port->
1378 ip_sscr &
1379 SSCR_RX_THRESHOLD)
1380 << PROD_CONS_PTR_OFF))) {
1381 port->ip_flags &= ~INPUT_HIGH;
1382 enable_intrs(port, hooks->intr_rx_high);
1383 }
1384 return total;
1385}
1386
1387/**
1388 * receive_chars - upper level read.
1389 * @the_port: port to read from
1390 */
1391static int receive_chars(struct uart_port *the_port)
1392{
1393 struct tty_struct *tty;
1394 unsigned char ch[MAX_CHARS];
1395 int read_count = 0, read_room, flip = 0;
Alan Coxebd2c8f2009-09-19 13:13:28 -07001396 struct uart_state *state = the_port->state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001397 struct ioc3_port *port = get_ioc3_port(the_port);
1398 unsigned long pflags;
1399
1400 /* Make sure all the pointers are "good" ones */
Alan Coxebd2c8f2009-09-19 13:13:28 -07001401 if (!state)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001402 return 0;
Alan Coxebd2c8f2009-09-19 13:13:28 -07001403 if (!state->port.tty)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001404 return 0;
1405
1406 if (!(port->ip_flags & INPUT_ENABLE))
1407 return 0;
1408
1409 spin_lock_irqsave(&the_port->lock, pflags);
Alan Coxebd2c8f2009-09-19 13:13:28 -07001410 tty = state->port.tty;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001411
1412 read_count = do_read(the_port, ch, MAX_CHARS);
1413 if (read_count > 0) {
1414 flip = 1;
Alan Cox4165fe42010-02-17 13:07:13 +00001415 read_room = tty_insert_flip_string(tty, ch, read_count);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001416 the_port->icount.rx += read_count;
1417 }
1418 spin_unlock_irqrestore(&the_port->lock, pflags);
1419
1420 if (flip)
1421 tty_flip_buffer_push(tty);
1422
1423 return read_count;
1424}
1425
1426/**
1427 * ioc3uart_intr_one - lowest level (per port) interrupt handler.
1428 * @is : submodule
1429 * @idd: driver data
1430 * @pending: interrupts to handle
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001431 */
1432
1433static int inline
1434ioc3uart_intr_one(struct ioc3_submodule *is,
1435 struct ioc3_driver_data *idd,
David Howells7d12e782006-10-05 14:55:46 +01001436 unsigned int pending)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001437{
1438 int port_num = GET_PORT_FROM_SIO_IR(pending);
1439 struct port_hooks *hooks;
1440 unsigned int rx_high_rd_aborted = 0;
1441 unsigned long flags;
1442 struct uart_port *the_port;
1443 struct ioc3_port *port;
1444 int loop_counter;
1445 struct ioc3_card *card_ptr;
1446 unsigned int sio_ir;
1447
1448 card_ptr = idd->data[is->id];
1449 port = card_ptr->ic_port[port_num].icp_port;
1450 hooks = port->ip_hooks;
1451
1452 /* Possible race condition here: The tx_mt interrupt bit may be
1453 * cleared without the intervention of the interrupt handler,
1454 * e.g. by a write. If the top level interrupt handler reads a
1455 * tx_mt, then some other processor does a write, starting up
1456 * output, then we come in here, see the tx_mt and stop DMA, the
1457 * output started by the other processor will hang. Thus we can
1458 * only rely on tx_mt being legitimate if it is read while the
1459 * port lock is held. Therefore this bit must be ignored in the
1460 * passed in interrupt mask which was read by the top level
1461 * interrupt handler since the port lock was not held at the time
1462 * it was read. We can only rely on this bit being accurate if it
1463 * is read while the port lock is held. So we'll clear it for now,
1464 * and reload it later once we have the port lock.
1465 */
1466
1467 sio_ir = pending & ~(hooks->intr_tx_mt);
1468 spin_lock_irqsave(&port->ip_lock, flags);
1469
1470 loop_counter = MAXITER; /* to avoid hangs */
1471
1472 do {
1473 uint32_t shadow;
1474
1475 if (loop_counter-- <= 0) {
1476 printk(KERN_WARNING "IOC3 serial: "
1477 "possible hang condition/"
1478 "port stuck on interrupt (line %d).\n",
1479 ((struct uart_port *)port->ip_port)->line);
1480 break;
1481 }
1482 /* Handle a DCD change */
1483 if (sio_ir & hooks->intr_delta_dcd) {
1484 ioc3_ack(is, idd, hooks->intr_delta_dcd);
1485 shadow = readl(&port->ip_serial_regs->shadow);
1486
1487 if ((port->ip_notify & N_DDCD)
1488 && (shadow & SHADOW_DCD)
1489 && (port->ip_port)) {
1490 the_port = port->ip_port;
1491 uart_handle_dcd_change(the_port,
1492 shadow & SHADOW_DCD);
1493 wake_up_interruptible
Alan Coxbdc04e32009-09-19 13:13:31 -07001494 (&the_port->state->port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001495 } else if ((port->ip_notify & N_DDCD)
1496 && !(shadow & SHADOW_DCD)) {
1497 /* Flag delta DCD/no DCD */
1498 uart_handle_dcd_change(port->ip_port,
1499 shadow & SHADOW_DCD);
1500 port->ip_flags |= DCD_ON;
1501 }
1502 }
1503
1504 /* Handle a CTS change */
1505 if (sio_ir & hooks->intr_delta_cts) {
1506 ioc3_ack(is, idd, hooks->intr_delta_cts);
1507 shadow = readl(&port->ip_serial_regs->shadow);
1508
1509 if ((port->ip_notify & N_DCTS) && (port->ip_port)) {
1510 the_port = port->ip_port;
1511 uart_handle_cts_change(the_port, shadow
1512 & SHADOW_CTS);
1513 wake_up_interruptible
Alan Coxbdc04e32009-09-19 13:13:31 -07001514 (&the_port->state->port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001515 }
1516 }
1517
1518 /* rx timeout interrupt. Must be some data available. Put this
1519 * before the check for rx_high since servicing this condition
1520 * may cause that condition to clear.
1521 */
1522 if (sio_ir & hooks->intr_rx_timer) {
1523 ioc3_ack(is, idd, hooks->intr_rx_timer);
1524 if ((port->ip_notify & N_DATA_READY)
1525 && (port->ip_port)) {
1526 receive_chars(port->ip_port);
1527 }
1528 }
1529
1530 /* rx high interrupt. Must be after rx_timer. */
1531 else if (sio_ir & hooks->intr_rx_high) {
1532 /* Data available, notify upper layer */
1533 if ((port->ip_notify & N_DATA_READY) && port->ip_port) {
1534 receive_chars(port->ip_port);
1535 }
1536
1537 /* We can't ACK this interrupt. If receive_chars didn't
1538 * cause the condition to clear, we'll have to disable
1539 * the interrupt until the data is drained.
1540 * If the read was aborted, don't disable the interrupt
1541 * as this may cause us to hang indefinitely. An
1542 * aborted read generally means that this interrupt
1543 * hasn't been delivered to the cpu yet anyway, even
1544 * though we see it as asserted when we read the sio_ir.
1545 */
1546 if ((sio_ir = PENDING(card_ptr, idd))
1547 & hooks->intr_rx_high) {
1548 if (port->ip_flags & READ_ABORTED) {
1549 rx_high_rd_aborted++;
1550 }
1551 else {
1552 card_ptr->ic_enable &= ~hooks->intr_rx_high;
1553 port->ip_flags |= INPUT_HIGH;
1554 }
1555 }
1556 }
1557
1558 /* We got a low water interrupt: notify upper layer to
1559 * send more data. Must come before tx_mt since servicing
1560 * this condition may cause that condition to clear.
1561 */
1562 if (sio_ir & hooks->intr_tx_explicit) {
1563 port->ip_flags &= ~LOWAT_WRITTEN;
1564 ioc3_ack(is, idd, hooks->intr_tx_explicit);
1565 if (port->ip_notify & N_OUTPUT_LOWAT)
1566 ioc3_cb_output_lowat(port);
1567 }
1568
1569 /* Handle tx_mt. Must come after tx_explicit. */
1570 else if (sio_ir & hooks->intr_tx_mt) {
1571 /* If we are expecting a lowat notification
1572 * and we get to this point it probably means that for
1573 * some reason the tx_explicit didn't work as expected
1574 * (that can legitimately happen if the output buffer is
1575 * filled up in just the right way).
1576 * So send the notification now.
1577 */
1578 if (port->ip_notify & N_OUTPUT_LOWAT) {
1579 ioc3_cb_output_lowat(port);
1580
1581 /* We need to reload the sio_ir since the lowat
1582 * call may have caused another write to occur,
1583 * clearing the tx_mt condition.
1584 */
1585 sio_ir = PENDING(card_ptr, idd);
1586 }
1587
1588 /* If the tx_mt condition still persists even after the
1589 * lowat call, we've got some work to do.
1590 */
1591 if (sio_ir & hooks->intr_tx_mt) {
1592 /* If we are not currently expecting DMA input,
1593 * and the transmitter has just gone idle,
1594 * there is no longer any reason for DMA, so
1595 * disable it.
1596 */
1597 if (!(port->ip_notify
1598 & (N_DATA_READY | N_DDCD))) {
1599 BUG_ON(!(port->ip_sscr
1600 & SSCR_DMA_EN));
1601 port->ip_sscr &= ~SSCR_DMA_EN;
1602 writel(port->ip_sscr,
1603 &port->ip_serial_regs->sscr);
1604 }
1605 /* Prevent infinite tx_mt interrupt */
1606 card_ptr->ic_enable &= ~hooks->intr_tx_mt;
1607 }
1608 }
1609 sio_ir = PENDING(card_ptr, idd);
1610
1611 /* if the read was aborted and only hooks->intr_rx_high,
1612 * clear hooks->intr_rx_high, so we do not loop forever.
1613 */
1614
1615 if (rx_high_rd_aborted && (sio_ir == hooks->intr_rx_high)) {
1616 sio_ir &= ~hooks->intr_rx_high;
1617 }
1618 } while (sio_ir & hooks->intr_all);
1619
1620 spin_unlock_irqrestore(&port->ip_lock, flags);
1621 ioc3_enable(is, idd, card_ptr->ic_enable);
1622 return 0;
1623}
1624
1625/**
1626 * ioc3uart_intr - field all serial interrupts
1627 * @is : submodule
1628 * @idd: driver data
1629 * @pending: interrupts to handle
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001630 *
1631 */
1632
1633static int ioc3uart_intr(struct ioc3_submodule *is,
1634 struct ioc3_driver_data *idd,
David Howells7d12e782006-10-05 14:55:46 +01001635 unsigned int pending)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001636{
1637 int ret = 0;
1638
1639 /*
1640 * The upper level interrupt handler sends interrupts for both ports
1641 * here. So we need to call for each port with its interrupts.
1642 */
1643
1644 if (pending & SIO_IR_SA)
David Howells7d12e782006-10-05 14:55:46 +01001645 ret |= ioc3uart_intr_one(is, idd, pending & SIO_IR_SA);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001646 if (pending & SIO_IR_SB)
David Howells7d12e782006-10-05 14:55:46 +01001647 ret |= ioc3uart_intr_one(is, idd, pending & SIO_IR_SB);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001648
1649 return ret;
1650}
1651
1652/**
1653 * ic3_type
1654 * @port: Port to operate with (we ignore since we only have one port)
1655 *
1656 */
1657static const char *ic3_type(struct uart_port *the_port)
1658{
1659 if (IS_RS232(the_port->line))
1660 return "SGI IOC3 Serial [rs232]";
1661 else
1662 return "SGI IOC3 Serial [rs422]";
1663}
1664
1665/**
1666 * ic3_tx_empty - Is the transmitter empty?
1667 * @port: Port to operate on
1668 *
1669 */
1670static unsigned int ic3_tx_empty(struct uart_port *the_port)
1671{
1672 unsigned int ret = 0;
1673 struct ioc3_port *port = get_ioc3_port(the_port);
1674
1675 if (readl(&port->ip_serial_regs->shadow) & SHADOW_TEMT)
1676 ret = TIOCSER_TEMT;
1677 return ret;
1678}
1679
1680/**
1681 * ic3_stop_tx - stop the transmitter
1682 * @port: Port to operate on
1683 *
1684 */
1685static void ic3_stop_tx(struct uart_port *the_port)
1686{
1687 struct ioc3_port *port = get_ioc3_port(the_port);
1688
1689 if (port)
1690 set_notification(port, N_OUTPUT_LOWAT, 0);
1691}
1692
1693/**
1694 * ic3_stop_rx - stop the receiver
1695 * @port: Port to operate on
1696 *
1697 */
1698static void ic3_stop_rx(struct uart_port *the_port)
1699{
1700 struct ioc3_port *port = get_ioc3_port(the_port);
1701
1702 if (port)
1703 port->ip_flags &= ~INPUT_ENABLE;
1704}
1705
1706/**
1707 * null_void_function
1708 * @port: Port to operate on
1709 *
1710 */
1711static void null_void_function(struct uart_port *the_port)
1712{
1713}
1714
1715/**
1716 * ic3_shutdown - shut down the port - free irq and disable
1717 * @port: port to shut down
1718 *
1719 */
1720static void ic3_shutdown(struct uart_port *the_port)
1721{
1722 unsigned long port_flags;
1723 struct ioc3_port *port;
Alan Coxebd2c8f2009-09-19 13:13:28 -07001724 struct uart_state *state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001725
1726 port = get_ioc3_port(the_port);
1727 if (!port)
1728 return;
1729
Alan Coxebd2c8f2009-09-19 13:13:28 -07001730 state = the_port->state;
Alan Coxbdc04e32009-09-19 13:13:31 -07001731 wake_up_interruptible(&state->port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001732
1733 spin_lock_irqsave(&the_port->lock, port_flags);
1734 set_notification(port, N_ALL, 0);
1735 spin_unlock_irqrestore(&the_port->lock, port_flags);
1736}
1737
1738/**
1739 * ic3_set_mctrl - set control lines (dtr, rts, etc)
1740 * @port: Port to operate on
1741 * @mctrl: Lines to set/unset
1742 *
1743 */
1744static void ic3_set_mctrl(struct uart_port *the_port, unsigned int mctrl)
1745{
1746 unsigned char mcr = 0;
1747
1748 if (mctrl & TIOCM_RTS)
1749 mcr |= UART_MCR_RTS;
1750 if (mctrl & TIOCM_DTR)
1751 mcr |= UART_MCR_DTR;
1752 if (mctrl & TIOCM_OUT1)
1753 mcr |= UART_MCR_OUT1;
1754 if (mctrl & TIOCM_OUT2)
1755 mcr |= UART_MCR_OUT2;
1756 if (mctrl & TIOCM_LOOP)
1757 mcr |= UART_MCR_LOOP;
1758
1759 set_mcr(the_port, mcr, SHADOW_DTR);
1760}
1761
1762/**
1763 * ic3_get_mctrl - get control line info
1764 * @port: port to operate on
1765 *
1766 */
1767static unsigned int ic3_get_mctrl(struct uart_port *the_port)
1768{
1769 struct ioc3_port *port = get_ioc3_port(the_port);
1770 uint32_t shadow;
1771 unsigned int ret = 0;
1772
1773 if (!port)
1774 return 0;
1775
1776 shadow = readl(&port->ip_serial_regs->shadow);
1777 if (shadow & SHADOW_DCD)
1778 ret |= TIOCM_CD;
1779 if (shadow & SHADOW_DR)
1780 ret |= TIOCM_DSR;
1781 if (shadow & SHADOW_CTS)
1782 ret |= TIOCM_CTS;
1783 return ret;
1784}
1785
1786/**
1787 * ic3_start_tx - Start transmitter. Called with the_port->lock
1788 * @port: Port to operate on
1789 *
1790 */
1791static void ic3_start_tx(struct uart_port *the_port)
1792{
1793 struct ioc3_port *port = get_ioc3_port(the_port);
1794
1795 if (port) {
1796 set_notification(port, N_OUTPUT_LOWAT, 1);
1797 enable_intrs(port, port->ip_hooks->intr_tx_mt);
1798 }
1799}
1800
1801/**
1802 * ic3_break_ctl - handle breaks
1803 * @port: Port to operate on
1804 * @break_state: Break state
1805 *
1806 */
1807static void ic3_break_ctl(struct uart_port *the_port, int break_state)
1808{
1809}
1810
1811/**
1812 * ic3_startup - Start up the serial port - always return 0 (We're always on)
1813 * @port: Port to operate on
1814 *
1815 */
1816static int ic3_startup(struct uart_port *the_port)
1817{
1818 int retval;
1819 struct ioc3_port *port;
1820 struct ioc3_card *card_ptr;
1821 unsigned long port_flags;
1822
1823 if (!the_port) {
1824 NOT_PROGRESS();
1825 return -ENODEV;
1826 }
1827 port = get_ioc3_port(the_port);
1828 if (!port) {
1829 NOT_PROGRESS();
1830 return -ENODEV;
1831 }
1832 card_ptr = port->ip_card;
1833 port->ip_port = the_port;
1834
1835 if (!card_ptr) {
1836 NOT_PROGRESS();
1837 return -ENODEV;
1838 }
1839
1840 /* Start up the serial port */
1841 spin_lock_irqsave(&the_port->lock, port_flags);
1842 retval = ic3_startup_local(the_port);
1843 spin_unlock_irqrestore(&the_port->lock, port_flags);
1844 return retval;
1845}
1846
1847/**
1848 * ic3_set_termios - set termios stuff
1849 * @port: port to operate on
1850 * @termios: New settings
1851 * @termios: Old
1852 *
1853 */
1854static void
1855ic3_set_termios(struct uart_port *the_port,
Alan Cox606d0992006-12-08 02:38:45 -08001856 struct ktermios *termios, struct ktermios *old_termios)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001857{
1858 unsigned long port_flags;
1859
1860 spin_lock_irqsave(&the_port->lock, port_flags);
1861 ioc3_change_speed(the_port, termios, old_termios);
1862 spin_unlock_irqrestore(&the_port->lock, port_flags);
1863}
1864
1865/**
1866 * ic3_request_port - allocate resources for port - no op....
1867 * @port: port to operate on
1868 *
1869 */
1870static int ic3_request_port(struct uart_port *port)
1871{
1872 return 0;
1873}
1874
1875/* Associate the uart functions above - given to serial core */
1876static struct uart_ops ioc3_ops = {
1877 .tx_empty = ic3_tx_empty,
1878 .set_mctrl = ic3_set_mctrl,
1879 .get_mctrl = ic3_get_mctrl,
1880 .stop_tx = ic3_stop_tx,
1881 .start_tx = ic3_start_tx,
1882 .stop_rx = ic3_stop_rx,
1883 .enable_ms = null_void_function,
1884 .break_ctl = ic3_break_ctl,
1885 .startup = ic3_startup,
1886 .shutdown = ic3_shutdown,
1887 .set_termios = ic3_set_termios,
1888 .type = ic3_type,
1889 .release_port = null_void_function,
1890 .request_port = ic3_request_port,
1891};
1892
1893/*
1894 * Boot-time initialization code
1895 */
1896
1897static struct uart_driver ioc3_uart = {
1898 .owner = THIS_MODULE,
1899 .driver_name = "ioc3_serial",
1900 .dev_name = DEVICE_NAME,
1901 .major = DEVICE_MAJOR,
1902 .minor = DEVICE_MINOR,
1903 .nr = MAX_LOGICAL_PORTS
1904};
1905
1906/**
1907 * ioc3_serial_core_attach - register with serial core
1908 * This is done during pci probing
1909 * @is: submodule struct for this
1910 * @idd: handle for this card
1911 */
1912static inline int ioc3_serial_core_attach( struct ioc3_submodule *is,
1913 struct ioc3_driver_data *idd)
1914{
1915 struct ioc3_port *port;
1916 struct uart_port *the_port;
1917 struct ioc3_card *card_ptr = idd->data[is->id];
1918 int ii, phys_port;
1919 struct pci_dev *pdev = idd->pdev;
1920
1921 DPRINT_CONFIG(("%s: attach pdev 0x%p - card_ptr 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001922 __func__, pdev, (void *)card_ptr));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001923
1924 if (!card_ptr)
1925 return -ENODEV;
1926
1927 /* once around for each logical port on this card */
1928 for (ii = 0; ii < LOGICAL_PORTS_PER_CARD; ii++) {
1929 phys_port = GET_PHYSICAL_PORT(ii);
1930 the_port = &card_ptr->ic_port[phys_port].
1931 icp_uart_port[GET_LOGICAL_PORT(ii)];
1932 port = card_ptr->ic_port[phys_port].icp_port;
1933 port->ip_port = the_port;
1934
1935 DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p [%d/%d]\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001936 __func__, (void *)the_port, (void *)port,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001937 phys_port, ii));
1938
1939 /* membase, iobase and mapbase just need to be non-0 */
1940 the_port->membase = (unsigned char __iomem *)1;
1941 the_port->iobase = (pdev->bus->number << 16) | ii;
1942 the_port->line = (Num_of_ioc3_cards << 2) | ii;
1943 the_port->mapbase = 1;
1944 the_port->type = PORT_16550A;
1945 the_port->fifosize = FIFO_SIZE;
1946 the_port->ops = &ioc3_ops;
1947 the_port->irq = idd->irq_io;
1948 the_port->dev = &pdev->dev;
1949
1950 if (uart_add_one_port(&ioc3_uart, the_port) < 0) {
1951 printk(KERN_WARNING
1952 "%s: unable to add port %d bus %d\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001953 __func__, the_port->line, pdev->bus->number);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001954 } else {
1955 DPRINT_CONFIG(("IOC3 serial port %d irq %d bus %d\n",
1956 the_port->line, the_port->irq, pdev->bus->number));
1957 }
1958
1959 /* all ports are rs232 for now */
1960 if (IS_PHYSICAL_PORT(ii))
1961 ioc3_set_proto(port, PROTO_RS232);
1962 }
1963 return 0;
1964}
1965
1966/**
1967 * ioc3uart_remove - register detach function
1968 * @is: submodule struct for this submodule
1969 * @idd: ioc3 driver data for this submodule
1970 */
1971
1972static int ioc3uart_remove(struct ioc3_submodule *is,
1973 struct ioc3_driver_data *idd)
1974{
1975 struct ioc3_card *card_ptr = idd->data[is->id];
1976 struct uart_port *the_port;
1977 struct ioc3_port *port;
1978 int ii;
1979
1980 if (card_ptr) {
1981 for (ii = 0; ii < LOGICAL_PORTS_PER_CARD; ii++) {
1982 the_port = &card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].
1983 icp_uart_port[GET_LOGICAL_PORT(ii)];
1984 if (the_port)
1985 uart_remove_one_port(&ioc3_uart, the_port);
1986 port = card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].icp_port;
1987 if (port && IS_PHYSICAL_PORT(ii)
1988 && (GET_PHYSICAL_PORT(ii) == 0)) {
1989 pci_free_consistent(port->ip_idd->pdev,
1990 TOTAL_RING_BUF_SIZE,
1991 (void *)port->ip_cpu_ringbuf,
1992 port->ip_dma_ringbuf);
1993 kfree(port);
1994 card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].
1995 icp_port = NULL;
1996 }
1997 }
1998 kfree(card_ptr);
1999 idd->data[is->id] = NULL;
2000 }
2001 return 0;
2002}
2003
2004/**
2005 * ioc3uart_probe - card probe function called from shim driver
2006 * @is: submodule struct for this submodule
2007 * @idd: ioc3 driver data for this card
2008 */
2009
2010static int __devinit
2011ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd)
2012{
2013 struct pci_dev *pdev = idd->pdev;
2014 struct ioc3_card *card_ptr;
2015 int ret = 0;
2016 struct ioc3_port *port;
2017 struct ioc3_port *ports[PORTS_PER_CARD];
2018 int phys_port;
2019
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002020 DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, is, idd));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002021
Burman Yan8f31bb32007-02-14 00:33:07 -08002022 card_ptr = kzalloc(sizeof(struct ioc3_card), GFP_KERNEL);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002023 if (!card_ptr) {
2024 printk(KERN_WARNING "ioc3_attach_one"
2025 ": unable to get memory for the IOC3\n");
2026 return -ENOMEM;
2027 }
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002028 idd->data[is->id] = card_ptr;
2029 Submodule_slot = is->id;
2030
2031 writel(((UARTA_BASE >> 3) << SIO_CR_SER_A_BASE_SHIFT) |
2032 ((UARTB_BASE >> 3) << SIO_CR_SER_B_BASE_SHIFT) |
2033 (0xf << SIO_CR_CMD_PULSE_SHIFT), &idd->vma->sio_cr);
2034
2035 pci_write_config_dword(pdev, PCI_LAT, 0xff00);
2036
2037 /* Enable serial port mode select generic PIO pins as outputs */
2038 ioc3_gpcr_set(idd, GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL);
2039
2040 /* Create port structures for each port */
2041 for (phys_port = 0; phys_port < PORTS_PER_CARD; phys_port++) {
Burman Yan8f31bb32007-02-14 00:33:07 -08002042 port = kzalloc(sizeof(struct ioc3_port), GFP_KERNEL);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002043 if (!port) {
2044 printk(KERN_WARNING
2045 "IOC3 serial memory not available for port\n");
2046 goto out4;
2047 }
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002048 spin_lock_init(&port->ip_lock);
2049
2050 /* we need to remember the previous ones, to point back to
2051 * them farther down - setting up the ring buffers.
2052 */
2053 ports[phys_port] = port;
2054
2055 /* init to something useful */
2056 card_ptr->ic_port[phys_port].icp_port = port;
2057 port->ip_is = is;
2058 port->ip_idd = idd;
2059 port->ip_baud = 9600;
2060 port->ip_card = card_ptr;
2061 port->ip_hooks = &hooks_array[phys_port];
2062
2063 /* Setup each port */
2064 if (phys_port == 0) {
2065 port->ip_serial_regs = &idd->vma->port_a;
2066 port->ip_uart_regs = &idd->vma->sregs.uarta;
2067
2068 DPRINT_CONFIG(("%s : Port A ip_serial_regs 0x%p "
2069 "ip_uart_regs 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002070 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002071 (void *)port->ip_serial_regs,
2072 (void *)port->ip_uart_regs));
2073
2074 /* setup ring buffers */
2075 port->ip_cpu_ringbuf = pci_alloc_consistent(pdev,
2076 TOTAL_RING_BUF_SIZE, &port->ip_dma_ringbuf);
2077
2078 BUG_ON(!((((int64_t) port->ip_dma_ringbuf) &
2079 (TOTAL_RING_BUF_SIZE - 1)) == 0));
2080 port->ip_inring = RING(port, RX_A);
2081 port->ip_outring = RING(port, TX_A);
2082 DPRINT_CONFIG(("%s : Port A ip_cpu_ringbuf 0x%p "
2083 "ip_dma_ringbuf 0x%p, ip_inring 0x%p "
2084 "ip_outring 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002085 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002086 (void *)port->ip_cpu_ringbuf,
2087 (void *)port->ip_dma_ringbuf,
2088 (void *)port->ip_inring,
2089 (void *)port->ip_outring));
2090 }
2091 else {
2092 port->ip_serial_regs = &idd->vma->port_b;
2093 port->ip_uart_regs = &idd->vma->sregs.uartb;
2094
2095 DPRINT_CONFIG(("%s : Port B ip_serial_regs 0x%p "
2096 "ip_uart_regs 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002097 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002098 (void *)port->ip_serial_regs,
2099 (void *)port->ip_uart_regs));
2100
2101 /* share the ring buffers */
2102 port->ip_dma_ringbuf =
2103 ports[phys_port - 1]->ip_dma_ringbuf;
2104 port->ip_cpu_ringbuf =
2105 ports[phys_port - 1]->ip_cpu_ringbuf;
2106 port->ip_inring = RING(port, RX_B);
2107 port->ip_outring = RING(port, TX_B);
2108 DPRINT_CONFIG(("%s : Port B ip_cpu_ringbuf 0x%p "
2109 "ip_dma_ringbuf 0x%p, ip_inring 0x%p "
2110 "ip_outring 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002111 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002112 (void *)port->ip_cpu_ringbuf,
2113 (void *)port->ip_dma_ringbuf,
2114 (void *)port->ip_inring,
2115 (void *)port->ip_outring));
2116 }
2117
2118 DPRINT_CONFIG(("%s : port %d [addr 0x%p] card_ptr 0x%p",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002119 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002120 phys_port, (void *)port, (void *)card_ptr));
2121 DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n",
2122 (void *)port->ip_serial_regs,
2123 (void *)port->ip_uart_regs));
2124
2125 /* Initialize the hardware for IOC3 */
2126 port_init(port);
2127
2128 DPRINT_CONFIG(("%s: phys_port %d port 0x%p inring 0x%p "
2129 "outring 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002130 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002131 phys_port, (void *)port,
2132 (void *)port->ip_inring,
2133 (void *)port->ip_outring));
2134
2135 }
2136
2137 /* register port with the serial core */
2138
2139 if ((ret = ioc3_serial_core_attach(is, idd)))
2140 goto out4;
2141
2142 Num_of_ioc3_cards++;
2143
2144 return ret;
2145
2146 /* error exits that give back resources */
2147out4:
2148 kfree(card_ptr);
2149 return ret;
2150}
2151
Tony Luck3c0db892008-12-08 16:16:21 -08002152static struct ioc3_submodule ioc3uart_ops = {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002153 .name = "IOC3uart",
2154 .probe = ioc3uart_probe,
2155 .remove = ioc3uart_remove,
2156 /* call .intr for both ports initially */
2157 .irq_mask = SIO_IR_SA | SIO_IR_SB,
2158 .intr = ioc3uart_intr,
2159 .owner = THIS_MODULE,
2160};
2161
2162/**
2163 * ioc3_detect - module init called,
2164 */
Jean Delvare2ea5d352009-12-14 18:00:27 -08002165static int __init ioc3uart_init(void)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002166{
2167 int ret;
2168
2169 /* register with serial core */
2170 if ((ret = uart_register_driver(&ioc3_uart)) < 0) {
2171 printk(KERN_WARNING
2172 "%s: Couldn't register IOC3 uart serial driver\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002173 __func__);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002174 return ret;
2175 }
Tony Luck3c0db892008-12-08 16:16:21 -08002176 ret = ioc3_register_submodule(&ioc3uart_ops);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002177 if (ret)
2178 uart_unregister_driver(&ioc3_uart);
2179 return ret;
2180}
2181
Jean Delvare2ea5d352009-12-14 18:00:27 -08002182static void __exit ioc3uart_exit(void)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002183{
Tony Luck3c0db892008-12-08 16:16:21 -08002184 ioc3_unregister_submodule(&ioc3uart_ops);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002185 uart_unregister_driver(&ioc3_uart);
2186}
2187
2188module_init(ioc3uart_init);
2189module_exit(ioc3uart_exit);
2190
2191MODULE_AUTHOR("Pat Gefre - Silicon Graphics Inc. (SGI) <pfg@sgi.com>");
2192MODULE_DESCRIPTION("Serial PCI driver module for SGI IOC3 card");
2193MODULE_LICENSE("GPL");