blob: 4c74c7ba2dff7cf6829684176c484ecbf356cea1 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001
Linus Torvalds1da177e2005-04-16 15:20:36 -07002#define PSEUDO_DMA
3#define DONT_USE_INTR
4#define UNSAFE /* Leave interrupts enabled during pseudo-dma I/O */
Linus Torvalds1da177e2005-04-16 15:20:36 -07005#define DMA_WORKS_RIGHT
6
7
8/*
9 * DTC 3180/3280 driver, by
10 * Ray Van Tassle rayvt@comm.mot.com
11 *
12 * taken from ...
13 * Trantor T128/T128F/T228 driver by...
14 *
15 * Drew Eckhardt
16 * Visionary Computing
17 * (Unix and Linux consulting and custom programming)
18 * drew@colorado.edu
19 * +1 (303) 440-4894
Finn Thain3f9e9862014-11-12 16:11:55 +110020 */
Linus Torvalds1da177e2005-04-16 15:20:36 -070021
22/*
Linus Torvalds1da177e2005-04-16 15:20:36 -070023 * The card is detected and initialized in one of several ways :
24 * 1. Autoprobe (default) - since the board is memory mapped,
25 * a BIOS signature is scanned for to locate the registers.
26 * An interrupt is triggered to autoprobe for the interrupt
27 * line.
28 *
29 * 2. With command line overrides - dtc=address,irq may be
30 * used on the LILO command line to override the defaults.
31 *
32*/
33
34/*----------------------------------------------------------------*/
35/* the following will set the monitor border color (useful to find
36 where something crashed or gets stuck at */
37/* 1 = blue
38 2 = green
39 3 = cyan
40 4 = red
41 5 = magenta
42 6 = yellow
43 7 = white
44*/
45#if 0
46#define rtrc(i) {inb(0x3da); outb(0x31, 0x3c0); outb((i), 0x3c0);}
47#else
48#define rtrc(i) {}
49#endif
50
51
Linus Torvalds1da177e2005-04-16 15:20:36 -070052#include <linux/module.h>
53#include <linux/signal.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070054#include <linux/blkdev.h>
55#include <linux/delay.h>
56#include <linux/stat.h>
57#include <linux/string.h>
58#include <linux/init.h>
59#include <linux/interrupt.h>
Matthew Wilcox53d5ed62006-10-11 01:22:01 -070060#include <linux/io.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070061#include <scsi/scsi_host.h>
62#include "dtc.h"
63#define AUTOPROBE_IRQ
64#include "NCR5380.h"
65
Linus Torvalds1da177e2005-04-16 15:20:36 -070066/*
67 * The DTC3180 & 3280 boards are memory mapped.
68 *
69 */
70
71/*
72 */
73/* Offset from DTC_5380_OFFSET */
74#define DTC_CONTROL_REG 0x100 /* rw */
75#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
76#define CSR_DIR_READ 0x40 /* rw direction, 1 = read 0 = write */
77
78#define CSR_RESET 0x80 /* wo Resets 53c400 */
79#define CSR_5380_REG 0x80 /* ro 5380 registers can be accessed */
80#define CSR_TRANS_DIR 0x40 /* rw Data transfer direction */
81#define CSR_SCSI_BUFF_INTR 0x20 /* rw Enable int on transfer ready */
82#define CSR_5380_INTR 0x10 /* rw Enable 5380 interrupts */
83#define CSR_SHARED_INTR 0x08 /* rw Interrupt sharing */
84#define CSR_HOST_BUF_NOT_RDY 0x04 /* ro Host buffer not ready */
85#define CSR_SCSI_BUF_RDY 0x02 /* ro SCSI buffer ready */
86#define CSR_GATED_5380_IRQ 0x01 /* ro Last block xferred */
87#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR | CSR_5380_INTR)
88
89
90#define DTC_BLK_CNT 0x101 /* rw
91 * # of 128-byte blocks to transfer */
92
93
94#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
95
96#define DTC_SWITCH_REG 0x3982 /* ro - DIP switches */
97#define DTC_RESUME_XFER 0x3982 /* wo - resume data xfer
98 * after disconnect/reconnect*/
99
100#define DTC_5380_OFFSET 0x3880 /* 8 registers here, see NCR5380.h */
101
102/*!!!! for dtc, it's a 128 byte buffer at 3900 !!! */
103#define DTC_DATA_BUF 0x3900 /* rw 128 bytes long */
104
105static struct override {
106 unsigned int address;
107 int irq;
108} overrides
109#ifdef OVERRIDE
110[] __initdata = OVERRIDE;
111#else
Alan Cox1fbe8522007-08-10 14:50:41 -0700112[4] __initdata = {
113 { 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }
114};
Linus Torvalds1da177e2005-04-16 15:20:36 -0700115#endif
116
Tobias Klauser6391a112006-06-08 22:23:48 -0700117#define NO_OVERRIDES ARRAY_SIZE(overrides)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700118
119static struct base {
120 unsigned long address;
121 int noauto;
Tobias Klauser6391a112006-06-08 22:23:48 -0700122} bases[] __initdata = {
123 { 0xcc000, 0 },
124 { 0xc8000, 0 },
125 { 0xdc000, 0 },
Linus Torvalds1da177e2005-04-16 15:20:36 -0700126 { 0xd8000, 0 }
127};
128
Tobias Klauser6391a112006-06-08 22:23:48 -0700129#define NO_BASES ARRAY_SIZE(bases)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700130
131static const struct signature {
132 const char *string;
133 int offset;
Tobias Klauser6391a112006-06-08 22:23:48 -0700134} signatures[] = {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700135 {"DATA TECHNOLOGY CORPORATION BIOS", 0x25},
136};
137
Tobias Klauser6391a112006-06-08 22:23:48 -0700138#define NO_SIGNATURES ARRAY_SIZE(signatures)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700139
140#ifndef MODULE
141/*
142 * Function : dtc_setup(char *str, int *ints)
143 *
144 * Purpose : LILO command line initialization of the overrides array,
Tobias Klauser6391a112006-06-08 22:23:48 -0700145 *
Linus Torvalds1da177e2005-04-16 15:20:36 -0700146 * Inputs : str - unused, ints - array of integer parameters with ints[0]
147 * equal to the number of ints.
148 *
Alan Cox1fbe8522007-08-10 14:50:41 -0700149 */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700150
Finn Thain925e4612014-11-12 16:11:49 +1100151static int __init dtc_setup(char *str)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700152{
153 static int commandline_current = 0;
154 int i;
Finn Thain925e4612014-11-12 16:11:49 +1100155 int ints[10];
156
157 get_options(str, ARRAY_SIZE(ints), ints);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700158 if (ints[0] != 2)
159 printk("dtc_setup: usage dtc=address,irq\n");
160 else if (commandline_current < NO_OVERRIDES) {
161 overrides[commandline_current].address = ints[1];
162 overrides[commandline_current].irq = ints[2];
163 for (i = 0; i < NO_BASES; ++i)
164 if (bases[i].address == ints[1]) {
165 bases[i].noauto = 1;
166 break;
167 }
168 ++commandline_current;
169 }
Finn Thain925e4612014-11-12 16:11:49 +1100170 return 1;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700171}
Finn Thain925e4612014-11-12 16:11:49 +1100172
173__setup("dtc=", dtc_setup);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700174#endif
175
176/*
Christoph Hellwigd0be4a7d2005-10-31 18:31:40 +0100177 * Function : int dtc_detect(struct scsi_host_template * tpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700178 *
179 * Purpose : detects and initializes DTC 3180/3280 controllers
180 * that were autoprobed, overridden on the LILO command line,
181 * or specified at compile time.
182 *
183 * Inputs : tpnt - template for this SCSI adapter.
184 *
185 * Returns : 1 if a host adapter was found, 0 if not.
186 *
187*/
188
Christoph Hellwigd0be4a7d2005-10-31 18:31:40 +0100189static int __init dtc_detect(struct scsi_host_template * tpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700190{
191 static int current_override = 0, current_base = 0;
192 struct Scsi_Host *instance;
193 unsigned int addr;
194 void __iomem *base;
195 int sig, count;
196
Linus Torvalds1da177e2005-04-16 15:20:36 -0700197 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
198 addr = 0;
199 base = NULL;
200
201 if (overrides[current_override].address) {
202 addr = overrides[current_override].address;
203 base = ioremap(addr, 0x2000);
204 if (!base)
205 addr = 0;
206 } else
207 for (; !addr && (current_base < NO_BASES); ++current_base) {
208#if (DTCDEBUG & DTCDEBUG_INIT)
Alan Cox1fbe8522007-08-10 14:50:41 -0700209 printk(KERN_DEBUG "scsi-dtc : probing address %08x\n", bases[current_base].address);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700210#endif
211 if (bases[current_base].noauto)
212 continue;
213 base = ioremap(bases[current_base].address, 0x2000);
214 if (!base)
215 continue;
216 for (sig = 0; sig < NO_SIGNATURES; ++sig) {
217 if (check_signature(base + signatures[sig].offset, signatures[sig].string, strlen(signatures[sig].string))) {
218 addr = bases[current_base].address;
219#if (DTCDEBUG & DTCDEBUG_INIT)
Alan Cox5307b1e2007-09-20 15:12:11 +0100220 printk(KERN_DEBUG "scsi-dtc : detected board.\n");
Linus Torvalds1da177e2005-04-16 15:20:36 -0700221#endif
222 goto found;
223 }
224 }
225 iounmap(base);
226 }
227
228#if defined(DTCDEBUG) && (DTCDEBUG & DTCDEBUG_INIT)
Alan Cox1fbe8522007-08-10 14:50:41 -0700229 printk(KERN_DEBUG "scsi-dtc : base = %08x\n", addr);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700230#endif
231
232 if (!addr)
233 break;
234
235found:
236 instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
237 if (instance == NULL)
238 break;
239
240 instance->base = addr;
241 ((struct NCR5380_hostdata *)(instance)->hostdata)->base = base;
242
243 NCR5380_init(instance, 0);
244
245 NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR); /* Enable int's */
246 if (overrides[current_override].irq != IRQ_AUTO)
247 instance->irq = overrides[current_override].irq;
248 else
249 instance->irq = NCR5380_probe_irq(instance, DTC_IRQS);
250
Finn Thain22f5f102014-11-12 16:11:56 +1100251 /* Compatibility with documented NCR5380 kernel parameters */
252 if (instance->irq == 255)
253 instance->irq = NO_IRQ;
254
Linus Torvalds1da177e2005-04-16 15:20:36 -0700255#ifndef DONT_USE_INTR
256 /* With interrupts enabled, it will sometimes hang when doing heavy
257 * reads. So better not enable them until I finger it out. */
Finn Thain22f5f102014-11-12 16:11:56 +1100258 if (instance->irq != NO_IRQ)
Michael Opdenacker4909cc22014-03-05 06:09:41 +0100259 if (request_irq(instance->irq, dtc_intr, 0,
Jeff Garzik1e641662007-11-11 19:52:05 -0500260 "dtc", instance)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700261 printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
Finn Thain22f5f102014-11-12 16:11:56 +1100262 instance->irq = NO_IRQ;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700263 }
264
Finn Thain22f5f102014-11-12 16:11:56 +1100265 if (instance->irq == NO_IRQ) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700266 printk(KERN_WARNING "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
267 printk(KERN_WARNING "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
268 }
269#else
Finn Thain22f5f102014-11-12 16:11:56 +1100270 if (instance->irq != NO_IRQ)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700271 printk(KERN_WARNING "scsi%d : interrupts not used. Might as well not jumper it.\n", instance->host_no);
Finn Thain22f5f102014-11-12 16:11:56 +1100272 instance->irq = NO_IRQ;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700273#endif
274#if defined(DTCDEBUG) && (DTCDEBUG & DTCDEBUG_INIT)
275 printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
276#endif
277
Linus Torvalds1da177e2005-04-16 15:20:36 -0700278 ++current_override;
279 ++count;
280 }
281 return count;
282}
283
284/*
285 * Function : int dtc_biosparam(Disk * disk, struct block_device *dev, int *ip)
286 *
287 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
288 * the specified device / size.
289 *
290 * Inputs : size = size of device in sectors (512 bytes), dev = block device
291 * major / minor, ip[] = {heads, sectors, cylinders}
292 *
293 * Returns : always 0 (success), initializes ip
294 *
295*/
296
297/*
298 * XXX Most SCSI boards use this mapping, I could be incorrect. Some one
299 * using hard disks on a trantor should verify that this mapping corresponds
300 * to that used by the BIOS / ASPI driver by running the linux fdisk program
301 * and matching the H_C_S coordinates to what DOS uses.
302*/
303
304static int dtc_biosparam(struct scsi_device *sdev, struct block_device *dev,
305 sector_t capacity, int *ip)
306{
307 int size = capacity;
308
309 ip[0] = 64;
310 ip[1] = 32;
311 ip[2] = size >> 11;
312 return 0;
313}
314
315
316/****************************************************************
317 * Function : int NCR5380_pread (struct Scsi_Host *instance,
318 * unsigned char *dst, int len)
319 *
320 * Purpose : Fast 5380 pseudo-dma read function, reads len bytes to
321 * dst
322 *
323 * Inputs : dst = destination, len = length in bytes
324 *
325 * Returns : 0 on success, non zero on a failure such as a watchdog
326 * timeout.
327*/
328
Linus Torvalds1da177e2005-04-16 15:20:36 -0700329static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
330{
331 unsigned char *d = dst;
332 int i; /* For counting time spent in the poll-loop */
Finn Thaina9c2dc42014-11-12 16:11:59 +1100333 struct NCR5380_hostdata *hostdata = shost_priv(instance);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700334 NCR5380_local_declare();
335 NCR5380_setup(instance);
336
337 i = 0;
338 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
339 NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
Finn Thain22f5f102014-11-12 16:11:56 +1100340 if (instance->irq == NO_IRQ)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700341 NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
342 else
343 NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ | CSR_INT_BASE);
344 NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
345 rtrc(1);
346 while (len > 0) {
347 rtrc(2);
348 while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
349 ++i;
350 rtrc(3);
351 memcpy_fromio(d, base + DTC_DATA_BUF, 128);
352 d += 128;
353 len -= 128;
354 rtrc(7);
355 /*** with int's on, it sometimes hangs after here.
356 * Looks like something makes HBNR go away. */
357 }
358 rtrc(4);
359 while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
360 ++i;
361 NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
362 rtrc(0);
363 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
Finn Thaina9c2dc42014-11-12 16:11:59 +1100364 if (i > hostdata->spin_max_r)
365 hostdata->spin_max_r = i;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700366 return (0);
367}
368
369/****************************************************************
370 * Function : int NCR5380_pwrite (struct Scsi_Host *instance,
371 * unsigned char *src, int len)
372 *
373 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
374 * src
375 *
376 * Inputs : src = source, len = length in bytes
377 *
378 * Returns : 0 on success, non zero on a failure such as a watchdog
379 * timeout.
380*/
381
382static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
383{
384 int i;
Finn Thaina9c2dc42014-11-12 16:11:59 +1100385 struct NCR5380_hostdata *hostdata = shost_priv(instance);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700386 NCR5380_local_declare();
387 NCR5380_setup(instance);
388
389 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
390 NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
391 /* set direction (write) */
Finn Thain22f5f102014-11-12 16:11:56 +1100392 if (instance->irq == NO_IRQ)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700393 NCR5380_write(DTC_CONTROL_REG, 0);
394 else
395 NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);
396 NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
397 for (i = 0; len > 0; ++i) {
398 rtrc(5);
399 /* Poll until the host buffer can accept data. */
400 while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
401 ++i;
402 rtrc(3);
403 memcpy_toio(base + DTC_DATA_BUF, src, 128);
404 src += 128;
405 len -= 128;
406 }
407 rtrc(4);
408 while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
409 ++i;
410 rtrc(6);
411 /* Wait until the last byte has been sent to the disk */
412 while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
413 ++i;
414 rtrc(7);
415 /* Check for parity error here. fixme. */
416 NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
417 rtrc(0);
Finn Thaina9c2dc42014-11-12 16:11:59 +1100418 if (i > hostdata->spin_max_w)
419 hostdata->spin_max_w = i;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700420 return (0);
421}
422
423MODULE_LICENSE("GPL");
424
425#include "NCR5380.c"
426
427static int dtc_release(struct Scsi_Host *shost)
428{
429 NCR5380_local_declare();
430 NCR5380_setup(shost);
Finn Thain22f5f102014-11-12 16:11:56 +1100431 if (shost->irq != NO_IRQ)
Jeff Garzik1e641662007-11-11 19:52:05 -0500432 free_irq(shost->irq, shost);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700433 NCR5380_exit(shost);
434 if (shost->io_port && shost->n_io_port)
435 release_region(shost->io_port, shost->n_io_port);
436 scsi_unregister(shost);
437 iounmap(base);
438 return 0;
439}
440
Christoph Hellwigd0be4a7d2005-10-31 18:31:40 +0100441static struct scsi_host_template driver_template = {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700442 .name = "DTC 3180/3280 ",
443 .detect = dtc_detect,
444 .release = dtc_release,
Finn Thain4d3d2a52014-11-12 16:11:52 +1100445 .proc_name = "dtc3x80",
446 .show_info = dtc_show_info,
447 .write_info = dtc_write_info,
Finn Thain8c325132014-11-12 16:11:58 +1100448 .info = dtc_info,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700449 .queuecommand = dtc_queue_command,
450 .eh_abort_handler = dtc_abort,
451 .eh_bus_reset_handler = dtc_bus_reset,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700452 .bios_param = dtc_biosparam,
453 .can_queue = CAN_QUEUE,
454 .this_id = 7,
455 .sg_tablesize = SG_ALL,
456 .cmd_per_lun = CMD_PER_LUN,
457 .use_clustering = DISABLE_CLUSTERING,
458};
459#include "scsi_module.c"