blob: 62c5d00abd2e85d745af7622fbd5a6eadab35c2f [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
Alan Coxc343a832007-05-25 20:39:30 +01002 * pata_it821x.c - IT821x PATA for new ATA layer
Jeff Garzik669a5db2006-08-29 18:12:40 -04003 * (C) 2005 Red Hat Inc
Alan Coxab771632008-10-27 15:09:10 +00004 * Alan Cox <alan@lxorguk.ukuu.org.uk>
Bartlomiej Zolnierkiewicz374abf22007-06-11 11:40:07 +02005 * (C) 2007 Bartlomiej Zolnierkiewicz
Jeff Garzik669a5db2006-08-29 18:12:40 -04006 *
7 * based upon
8 *
9 * it821x.c
Jeff Garzik85cd7252006-08-31 00:03:49 -040010 *
Jeff Garzik669a5db2006-08-29 18:12:40 -040011 * linux/drivers/ide/pci/it821x.c Version 0.09 December 2004
12 *
Alan Coxab771632008-10-27 15:09:10 +000013 * Copyright (C) 2004 Red Hat
Jeff Garzik669a5db2006-08-29 18:12:40 -040014 *
15 * May be copied or modified under the terms of the GNU General Public License
16 * Based in part on the ITE vendor provided SCSI driver.
17 *
Justin P. Mattock631dd1a2010-10-18 11:03:14 +020018 * Documentation available from IT8212F_V04.pdf
19 * http://www.ite.com.tw/EN/products_more.aspx?CategoryID=3&ID=5,91
Jeff Garzik669a5db2006-08-29 18:12:40 -040020 * Some other documents are NDA.
21 *
22 * The ITE8212 isn't exactly a standard IDE controller. It has two
23 * modes. In pass through mode then it is an IDE controller. In its smart
24 * mode its actually quite a capable hardware raid controller disguised
25 * as an IDE controller. Smart mode only understands DMA read/write and
26 * identify, none of the fancier commands apply. The IT8211 is identical
27 * in other respects but lacks the raid mode.
28 *
29 * Errata:
30 * o Rev 0x10 also requires master/slave hold the same DMA timings and
31 * cannot do ATAPI MWDMA.
32 * o The identify data for raid volumes lacks CHS info (technically ok)
33 * but also fails to set the LBA28 and other bits. We fix these in
34 * the IDE probe quirk code.
35 * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
36 * raid then the controller firmware dies
37 * o Smart mode without RAID doesn't clear all the necessary identify
38 * bits to reduce the command set to the one used
39 *
40 * This has a few impacts on the driver
41 * - In pass through mode we do all the work you would expect
42 * - In smart mode the clocking set up is done by the controller generally
43 * but we must watch the other limits and filter.
44 * - There are a few extra vendor commands that actually talk to the
45 * controller but only work PIO with no IRQ.
46 *
47 * Vendor areas of the identify block in smart mode are used for the
48 * timing and policy set up. Each HDD in raid mode also has a serial
49 * block on the disk. The hardware extra commands are get/set chip status,
50 * rebuild, get rebuild status.
51 *
52 * In Linux the driver supports pass through mode as if the device was
53 * just another IDE controller. If the smart mode is running then
54 * volumes are managed by the controller firmware and each IDE "disk"
55 * is a raid volume. Even more cute - the controller can do automated
56 * hotplug and rebuild.
57 *
58 * The pass through controller itself is a little demented. It has a
59 * flaw that it has a single set of PIO/MWDMA timings per channel so
60 * non UDMA devices restrict each others performance. It also has a
61 * single clock source per channel so mixed UDMA100/133 performance
62 * isn't perfect and we have to pick a clock. Thankfully none of this
63 * matters in smart mode. ATAPI DMA is not currently supported.
64 *
65 * It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
66 *
67 * TODO
68 * - ATAPI and other speed filtering
Jeff Garzik669a5db2006-08-29 18:12:40 -040069 * - RAID configuration ioctls
70 */
71
72#include <linux/kernel.h>
73#include <linux/module.h>
74#include <linux/pci.h>
75#include <linux/init.h>
76#include <linux/blkdev.h>
77#include <linux/delay.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090078#include <linux/slab.h>
Jeff Garzik669a5db2006-08-29 18:12:40 -040079#include <scsi/scsi_host.h>
80#include <linux/libata.h>
81
82
83#define DRV_NAME "pata_it821x"
Alan Cox4a99d952009-01-11 19:51:08 +000084#define DRV_VERSION "0.4.2"
Jeff Garzik669a5db2006-08-29 18:12:40 -040085
86struct it821x_dev
87{
88 unsigned int smart:1, /* Are we in smart raid mode */
89 timing10:1; /* Rev 0x10 */
90 u8 clock_mode; /* 0, ATA_50 or ATA_66 */
91 u8 want[2][2]; /* Mode/Pri log for master slave */
92 /* We need these for switching the clock when DMA goes on/off
93 The high byte is the 66Mhz timing */
94 u16 pio[2]; /* Cached PIO values */
95 u16 mwdma[2]; /* Cached MWDMA values */
96 u16 udma[2]; /* Cached UDMA values (per drive) */
97 u16 last_device; /* Master or slave loaded ? */
98};
99
100#define ATA_66 0
101#define ATA_50 1
102#define ATA_ANY 2
103
104#define UDMA_OFF 0
105#define MWDMA_OFF 0
106
107/*
108 * We allow users to force the card into non raid mode without
Robert P. J. Day3a4fa0a2007-10-19 23:10:43 +0200109 * flashing the alternative BIOS. This is also necessary right now
Jeff Garzik669a5db2006-08-29 18:12:40 -0400110 * for embedded platforms that cannot run a PC BIOS but are using this
111 * device.
112 */
113
114static int it8212_noraid;
115
116/**
Jeff Garzik669a5db2006-08-29 18:12:40 -0400117 * it821x_program - program the PIO/MWDMA registers
118 * @ap: ATA port
119 * @adev: Device to program
120 * @timing: Timing value (66Mhz in top 8bits, 50 in the low 8)
121 *
122 * Program the PIO/MWDMA timing for this channel according to the
123 * current clock. These share the same register so are managed by
124 * the DMA start/stop sequence as with the old driver.
125 */
126
127static void it821x_program(struct ata_port *ap, struct ata_device *adev, u16 timing)
128{
129 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
130 struct it821x_dev *itdev = ap->private_data;
131 int channel = ap->port_no;
132 u8 conf;
133
134 /* Program PIO/MWDMA timing bits */
135 if (itdev->clock_mode == ATA_66)
136 conf = timing >> 8;
137 else
138 conf = timing & 0xFF;
139 pci_write_config_byte(pdev, 0x54 + 4 * channel, conf);
140}
141
142
143/**
144 * it821x_program_udma - program the UDMA registers
145 * @ap: ATA port
146 * @adev: ATA device to update
147 * @timing: Timing bits. Top 8 are for 66Mhz bottom for 50Mhz
148 *
149 * Program the UDMA timing for this drive according to the
150 * current clock. Handles the dual clocks and also knows about
151 * the errata on the 0x10 revision. The UDMA errata is partly handled
152 * here and partly in start_dma.
153 */
154
155static void it821x_program_udma(struct ata_port *ap, struct ata_device *adev, u16 timing)
156{
157 struct it821x_dev *itdev = ap->private_data;
158 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
159 int channel = ap->port_no;
160 int unit = adev->devno;
161 u8 conf;
162
163 /* Program UDMA timing bits */
164 if (itdev->clock_mode == ATA_66)
165 conf = timing >> 8;
166 else
167 conf = timing & 0xFF;
168 if (itdev->timing10 == 0)
169 pci_write_config_byte(pdev, 0x56 + 4 * channel + unit, conf);
170 else {
171 /* Early revision must be programmed for both together */
172 pci_write_config_byte(pdev, 0x56 + 4 * channel, conf);
173 pci_write_config_byte(pdev, 0x56 + 4 * channel + 1, conf);
174 }
175}
176
177/**
178 * it821x_clock_strategy
179 * @ap: ATA interface
180 * @adev: ATA device being updated
181 *
182 * Select between the 50 and 66Mhz base clocks to get the best
183 * results for this interface.
184 */
185
186static void it821x_clock_strategy(struct ata_port *ap, struct ata_device *adev)
187{
188 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
189 struct it821x_dev *itdev = ap->private_data;
190 u8 unit = adev->devno;
191 struct ata_device *pair = ata_dev_pair(adev);
192
193 int clock, altclock;
194 u8 v;
195 int sel = 0;
196
197 /* Look for the most wanted clocking */
198 if (itdev->want[0][0] > itdev->want[1][0]) {
199 clock = itdev->want[0][1];
200 altclock = itdev->want[1][1];
201 } else {
202 clock = itdev->want[1][1];
203 altclock = itdev->want[0][1];
204 }
205
206 /* Master doesn't care does the slave ? */
207 if (clock == ATA_ANY)
208 clock = altclock;
209
210 /* Nobody cares - keep the same clock */
211 if (clock == ATA_ANY)
212 return;
213 /* No change */
214 if (clock == itdev->clock_mode)
215 return;
216
217 /* Load this into the controller */
218 if (clock == ATA_66)
219 itdev->clock_mode = ATA_66;
220 else {
221 itdev->clock_mode = ATA_50;
222 sel = 1;
223 }
224 pci_read_config_byte(pdev, 0x50, &v);
225 v &= ~(1 << (1 + ap->port_no));
226 v |= sel << (1 + ap->port_no);
227 pci_write_config_byte(pdev, 0x50, v);
228
229 /*
230 * Reprogram the UDMA/PIO of the pair drive for the switch
231 * MWDMA will be dealt with by the dma switcher
232 */
233 if (pair && itdev->udma[1-unit] != UDMA_OFF) {
234 it821x_program_udma(ap, pair, itdev->udma[1-unit]);
235 it821x_program(ap, pair, itdev->pio[1-unit]);
236 }
237 /*
238 * Reprogram the UDMA/PIO of our drive for the switch.
239 * MWDMA will be dealt with by the dma switcher
240 */
241 if (itdev->udma[unit] != UDMA_OFF) {
242 it821x_program_udma(ap, adev, itdev->udma[unit]);
243 it821x_program(ap, adev, itdev->pio[unit]);
244 }
245}
246
247/**
248 * it821x_passthru_set_piomode - set PIO mode data
249 * @ap: ATA interface
250 * @adev: ATA device
251 *
252 * Configure for PIO mode. This is complicated as the register is
253 * shared by PIO and MWDMA and for both channels.
254 */
255
256static void it821x_passthru_set_piomode(struct ata_port *ap, struct ata_device *adev)
257{
258 /* Spec says 89 ref driver uses 88 */
259 static const u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
260 static const u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
261
262 struct it821x_dev *itdev = ap->private_data;
263 int unit = adev->devno;
264 int mode_wanted = adev->pio_mode - XFER_PIO_0;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400265
Jeff Garzik669a5db2006-08-29 18:12:40 -0400266 /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
267 itdev->want[unit][1] = pio_want[mode_wanted];
268 itdev->want[unit][0] = 1; /* PIO is lowest priority */
269 itdev->pio[unit] = pio[mode_wanted];
270 it821x_clock_strategy(ap, adev);
271 it821x_program(ap, adev, itdev->pio[unit]);
272}
273
274/**
275 * it821x_passthru_set_dmamode - set initial DMA mode data
276 * @ap: ATA interface
277 * @adev: ATA device
278 *
279 * Set up the DMA modes. The actions taken depend heavily on the mode
Jeff Garzik85cd7252006-08-31 00:03:49 -0400280 * to use. If UDMA is used as is hopefully the usual case then the
Jeff Garzik669a5db2006-08-29 18:12:40 -0400281 * timing register is private and we need only consider the clock. If
282 * we are using MWDMA then we have to manage the setting ourself as
283 * we switch devices and mode.
284 */
285
286static void it821x_passthru_set_dmamode(struct ata_port *ap, struct ata_device *adev)
287{
288 static const u16 dma[] = { 0x8866, 0x3222, 0x3121 };
289 static const u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY };
290 static const u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
291 static const u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
292
293 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
294 struct it821x_dev *itdev = ap->private_data;
295 int channel = ap->port_no;
296 int unit = adev->devno;
297 u8 conf;
298
299 if (adev->dma_mode >= XFER_UDMA_0) {
300 int mode_wanted = adev->dma_mode - XFER_UDMA_0;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400301
Jeff Garzik669a5db2006-08-29 18:12:40 -0400302 itdev->want[unit][1] = udma_want[mode_wanted];
303 itdev->want[unit][0] = 3; /* UDMA is high priority */
304 itdev->mwdma[unit] = MWDMA_OFF;
305 itdev->udma[unit] = udma[mode_wanted];
306 if (mode_wanted >= 5)
307 itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
308
309 /* UDMA on. Again revision 0x10 must do the pair */
310 pci_read_config_byte(pdev, 0x50, &conf);
311 if (itdev->timing10)
312 conf &= channel ? 0x9F: 0xE7;
313 else
314 conf &= ~ (1 << (3 + 2 * channel + unit));
315 pci_write_config_byte(pdev, 0x50, conf);
316 it821x_clock_strategy(ap, adev);
317 it821x_program_udma(ap, adev, itdev->udma[unit]);
318 } else {
319 int mode_wanted = adev->dma_mode - XFER_MW_DMA_0;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400320
Jeff Garzik669a5db2006-08-29 18:12:40 -0400321 itdev->want[unit][1] = mwdma_want[mode_wanted];
322 itdev->want[unit][0] = 2; /* MWDMA is low priority */
323 itdev->mwdma[unit] = dma[mode_wanted];
324 itdev->udma[unit] = UDMA_OFF;
325
326 /* UDMA bits off - Revision 0x10 do them in pairs */
327 pci_read_config_byte(pdev, 0x50, &conf);
328 if (itdev->timing10)
329 conf |= channel ? 0x60: 0x18;
330 else
331 conf |= 1 << (3 + 2 * channel + unit);
332 pci_write_config_byte(pdev, 0x50, conf);
333 it821x_clock_strategy(ap, adev);
334 }
335}
336
337/**
338 * it821x_passthru_dma_start - DMA start callback
339 * @qc: Command in progress
340 *
341 * Usually drivers set the DMA timing at the point the set_dmamode call
Jeff Garzik85cd7252006-08-31 00:03:49 -0400342 * is made. IT821x however requires we load new timings on the
Jeff Garzik669a5db2006-08-29 18:12:40 -0400343 * transitions in some cases.
344 */
345
346static void it821x_passthru_bmdma_start(struct ata_queued_cmd *qc)
347{
348 struct ata_port *ap = qc->ap;
349 struct ata_device *adev = qc->dev;
350 struct it821x_dev *itdev = ap->private_data;
351 int unit = adev->devno;
352
353 if (itdev->mwdma[unit] != MWDMA_OFF)
354 it821x_program(ap, adev, itdev->mwdma[unit]);
355 else if (itdev->udma[unit] != UDMA_OFF && itdev->timing10)
356 it821x_program_udma(ap, adev, itdev->udma[unit]);
357 ata_bmdma_start(qc);
358}
359
360/**
361 * it821x_passthru_dma_stop - DMA stop callback
362 * @qc: ATA command
363 *
364 * We loaded new timings in dma_start, as a result we need to restore
365 * the PIO timings in dma_stop so that the next command issue gets the
366 * right clock values.
367 */
368
369static void it821x_passthru_bmdma_stop(struct ata_queued_cmd *qc)
370{
371 struct ata_port *ap = qc->ap;
372 struct ata_device *adev = qc->dev;
373 struct it821x_dev *itdev = ap->private_data;
374 int unit = adev->devno;
375
376 ata_bmdma_stop(qc);
377 if (itdev->mwdma[unit] != MWDMA_OFF)
378 it821x_program(ap, adev, itdev->pio[unit]);
379}
380
381
382/**
383 * it821x_passthru_dev_select - Select master/slave
384 * @ap: ATA port
385 * @device: Device number (not pointer)
386 *
Robert P. J. Day3a4fa0a2007-10-19 23:10:43 +0200387 * Device selection hook. If necessary perform clock switching
Jeff Garzik669a5db2006-08-29 18:12:40 -0400388 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400389
Jeff Garzik669a5db2006-08-29 18:12:40 -0400390static void it821x_passthru_dev_select(struct ata_port *ap,
391 unsigned int device)
392{
393 struct it821x_dev *itdev = ap->private_data;
394 if (itdev && device != itdev->last_device) {
Tejun Heo9af5c9c2007-08-06 18:36:22 +0900395 struct ata_device *adev = &ap->link.device[device];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400396 it821x_program(ap, adev, itdev->pio[adev->devno]);
397 itdev->last_device = device;
398 }
Tejun Heo9363c382008-04-07 22:47:16 +0900399 ata_sff_dev_select(ap, device);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400400}
401
402/**
Tejun Heo9363c382008-04-07 22:47:16 +0900403 * it821x_smart_qc_issue - wrap qc issue prot
Jeff Garzik669a5db2006-08-29 18:12:40 -0400404 * @qc: command
405 *
406 * Wrap the command issue sequence for the IT821x. We need to
407 * perform out own device selection timing loads before the
408 * usual happenings kick off
409 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400410
Tejun Heo9363c382008-04-07 22:47:16 +0900411static unsigned int it821x_smart_qc_issue(struct ata_queued_cmd *qc)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400412{
413 switch(qc->tf.command)
414 {
415 /* Commands the firmware supports */
416 case ATA_CMD_READ:
417 case ATA_CMD_READ_EXT:
418 case ATA_CMD_WRITE:
419 case ATA_CMD_WRITE_EXT:
420 case ATA_CMD_PIO_READ:
421 case ATA_CMD_PIO_READ_EXT:
422 case ATA_CMD_PIO_WRITE:
423 case ATA_CMD_PIO_WRITE_EXT:
424 case ATA_CMD_READ_MULTI:
425 case ATA_CMD_READ_MULTI_EXT:
426 case ATA_CMD_WRITE_MULTI:
427 case ATA_CMD_WRITE_MULTI_EXT:
428 case ATA_CMD_ID_ATA:
Alan Cox963e4972008-07-24 17:16:06 +0100429 case ATA_CMD_INIT_DEV_PARAMS:
430 case 0xFC: /* Internal 'report rebuild state' */
Jeff Garzik669a5db2006-08-29 18:12:40 -0400431 /* Arguably should just no-op this one */
432 case ATA_CMD_SET_FEATURES:
Tejun Heo360ff782010-05-10 21:41:42 +0200433 return ata_bmdma_qc_issue(qc);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400434 }
435 printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command);
Alan Coxc5038fc2007-10-25 14:21:16 +0100436 return AC_ERR_DEV;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400437}
438
439/**
Tejun Heo9363c382008-04-07 22:47:16 +0900440 * it821x_passthru_qc_issue - wrap qc issue prot
Jeff Garzik669a5db2006-08-29 18:12:40 -0400441 * @qc: command
442 *
443 * Wrap the command issue sequence for the IT821x. We need to
444 * perform out own device selection timing loads before the
445 * usual happenings kick off
446 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400447
Tejun Heo9363c382008-04-07 22:47:16 +0900448static unsigned int it821x_passthru_qc_issue(struct ata_queued_cmd *qc)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400449{
450 it821x_passthru_dev_select(qc->ap, qc->dev->devno);
Tejun Heo360ff782010-05-10 21:41:42 +0200451 return ata_bmdma_qc_issue(qc);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400452}
453
454/**
455 * it821x_smart_set_mode - mode setting
Tejun Heo02607312007-08-06 18:36:23 +0900456 * @link: interface to set up
Alanb229a7b2007-01-24 11:47:07 +0000457 * @unused: device that failed (error only)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400458 *
459 * Use a non standard set_mode function. We don't want to be tuned.
460 * The BIOS configured everything. Our job is not to fiddle. We
461 * read the dma enabled bits from the PCI configuration of the device
Jeff Garzik85cd7252006-08-31 00:03:49 -0400462 * and respect them.
Jeff Garzik669a5db2006-08-29 18:12:40 -0400463 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400464
Tejun Heo02607312007-08-06 18:36:23 +0900465static int it821x_smart_set_mode(struct ata_link *link, struct ata_device **unused)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400466{
Tejun Heof58229f2007-08-06 18:36:23 +0900467 struct ata_device *dev;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400468
Tejun Heo1eca4362008-11-03 20:03:17 +0900469 ata_for_each_dev(dev, link, ENABLED) {
470 /* We don't really care */
471 dev->pio_mode = XFER_PIO_0;
472 dev->dma_mode = XFER_MW_DMA_0;
473 /* We do need the right mode information for DMA or PIO
474 and this comes from the current configuration flags */
475 if (ata_id_has_dma(dev->id)) {
Joe Perchesa9a79df2011-04-15 15:51:59 -0700476 ata_dev_info(dev, "configured for DMA\n");
Tejun Heo1eca4362008-11-03 20:03:17 +0900477 dev->xfer_mode = XFER_MW_DMA_0;
478 dev->xfer_shift = ATA_SHIFT_MWDMA;
479 dev->flags &= ~ATA_DFLAG_PIO;
480 } else {
Joe Perchesa9a79df2011-04-15 15:51:59 -0700481 ata_dev_info(dev, "configured for PIO\n");
Tejun Heo1eca4362008-11-03 20:03:17 +0900482 dev->xfer_mode = XFER_PIO_0;
483 dev->xfer_shift = ATA_SHIFT_PIO;
484 dev->flags |= ATA_DFLAG_PIO;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400485 }
486 }
Alanb229a7b2007-01-24 11:47:07 +0000487 return 0;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400488}
489
490/**
491 * it821x_dev_config - Called each device identify
Jeff Garzik669a5db2006-08-29 18:12:40 -0400492 * @adev: Device that has just been identified
493 *
494 * Perform the initial setup needed for each device that is chip
495 * special. In our case we need to lock the sector count to avoid
496 * blowing the brains out of the firmware with large LBA48 requests
497 *
Jeff Garzik669a5db2006-08-29 18:12:40 -0400498 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400499
Alancd0d3bb2007-03-02 00:56:15 +0000500static void it821x_dev_config(struct ata_device *adev)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400501{
Tejun Heo8bfa79f2007-01-02 20:19:40 +0900502 unsigned char model_num[ATA_ID_PROD_LEN + 1];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400503
Tejun Heo8bfa79f2007-01-02 20:19:40 +0900504 ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num));
Jeff Garzik669a5db2006-08-29 18:12:40 -0400505
506 if (adev->max_sectors > 255)
507 adev->max_sectors = 255;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400508
Jeff Garzik669a5db2006-08-29 18:12:40 -0400509 if (strstr(model_num, "Integrated Technology Express")) {
510 /* RAID mode */
Joe Perchesa9a79df2011-04-15 15:51:59 -0700511 ata_dev_info(adev, "%sRAID%d volume",
512 adev->id[147] ? "Bootable " : "",
513 adev->id[129]);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400514 if (adev->id[129] != 1)
Joe Perchesa9a79df2011-04-15 15:51:59 -0700515 pr_cont("(%dK stripe)", adev->id[146]);
516 pr_cont("\n");
Jeff Garzik669a5db2006-08-29 18:12:40 -0400517 }
Alan Coxc5038fc2007-10-25 14:21:16 +0100518 /* This is a controller firmware triggered funny, don't
519 report the drive faulty! */
520 adev->horkage &= ~ATA_HORKAGE_DIAGNOSTIC;
Alan Cox963e4972008-07-24 17:16:06 +0100521 /* No HPA in 'smart' mode */
522 adev->horkage |= ATA_HORKAGE_BROKEN_HPA;
Alan Coxc5038fc2007-10-25 14:21:16 +0100523}
524
525/**
Alan Cox963e4972008-07-24 17:16:06 +0100526 * it821x_read_id - Hack identify data up
527 * @adev: device to read
528 * @tf: proposed taskfile
529 * @id: buffer for returned ident data
Alan Coxc5038fc2007-10-25 14:21:16 +0100530 *
Alan Cox963e4972008-07-24 17:16:06 +0100531 * Query the devices on this firmware driven port and slightly
Alan Coxc5038fc2007-10-25 14:21:16 +0100532 * mash the identify data to stop us and common tools trying to
533 * use features not firmware supported. The firmware itself does
534 * some masking (eg SMART) but not enough.
Alan Coxc5038fc2007-10-25 14:21:16 +0100535 */
536
Alan Cox963e4972008-07-24 17:16:06 +0100537static unsigned int it821x_read_id(struct ata_device *adev,
538 struct ata_taskfile *tf, u16 *id)
Alan Coxc5038fc2007-10-25 14:21:16 +0100539{
Alan Cox963e4972008-07-24 17:16:06 +0100540 unsigned int err_mask;
541 unsigned char model_num[ATA_ID_PROD_LEN + 1];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400542
Alan Cox963e4972008-07-24 17:16:06 +0100543 err_mask = ata_do_dev_read_id(adev, tf, id);
544 if (err_mask)
545 return err_mask;
546 ata_id_c_string(id, model_num, ATA_ID_PROD, sizeof(model_num));
547
548 id[83] &= ~(1 << 12); /* Cache flush is firmware handled */
549 id[83] &= ~(1 << 13); /* Ditto for LBA48 flushes */
550 id[84] &= ~(1 << 6); /* No FUA */
551 id[85] &= ~(1 << 10); /* No HPA */
552 id[76] = 0; /* No NCQ/AN etc */
553
554 if (strstr(model_num, "Integrated Technology Express")) {
555 /* Set feature bits the firmware neglects */
556 id[49] |= 0x0300; /* LBA, DMA */
Alan Cox963e4972008-07-24 17:16:06 +0100557 id[83] &= 0x7FFF;
Ondrej Zary054e5f62008-10-26 18:10:19 -0400558 id[83] |= 0x4400; /* Word 83 is valid and LBA48 */
Alan Cox963e4972008-07-24 17:16:06 +0100559 id[86] |= 0x0400; /* LBA48 on */
560 id[ATA_ID_MAJOR_VER] |= 0x1F;
Ondrej Zary7ba07d12009-02-11 13:08:43 -0800561 /* Clear the serial number because it's different each boot
562 which breaks validation on resume */
563 memset(&id[ATA_ID_SERNO], 0x20, ATA_ID_SERNO_LEN);
Alan Cox963e4972008-07-24 17:16:06 +0100564 }
565 return err_mask;
566}
Jeff Garzik669a5db2006-08-29 18:12:40 -0400567
568/**
569 * it821x_check_atapi_dma - ATAPI DMA handler
570 * @qc: Command we are about to issue
571 *
572 * Decide if this ATAPI command can be issued by DMA on this
573 * controller. Return 0 if it can be.
574 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400575
Jeff Garzik669a5db2006-08-29 18:12:40 -0400576static int it821x_check_atapi_dma(struct ata_queued_cmd *qc)
577{
578 struct ata_port *ap = qc->ap;
579 struct it821x_dev *itdev = ap->private_data;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400580
Jeff Nordenbce7d5e2007-09-04 11:07:20 -0500581 /* Only use dma for transfers to/from the media. */
Tejun Heob63b1332008-03-18 17:56:12 +0900582 if (ata_qc_raw_nbytes(qc) < 2048)
Jeff Nordenbce7d5e2007-09-04 11:07:20 -0500583 return -EOPNOTSUPP;
584
Jeff Garzik669a5db2006-08-29 18:12:40 -0400585 /* No ATAPI DMA in smart mode */
586 if (itdev->smart)
587 return -EOPNOTSUPP;
588 /* No ATAPI DMA on rev 10 */
589 if (itdev->timing10)
590 return -EOPNOTSUPP;
591 /* Cool */
592 return 0;
593}
Jeff Garzik85cd7252006-08-31 00:03:49 -0400594
Alan Cox963e4972008-07-24 17:16:06 +0100595/**
596 * it821x_display_disk - display disk setup
597 * @n: Device number
598 * @buf: Buffer block from firmware
599 *
600 * Produce a nice informative display of the device setup as provided
601 * by the firmware.
602 */
603
604static void it821x_display_disk(int n, u8 *buf)
605{
606 unsigned char id[41];
607 int mode = 0;
Jeff Garzik4ef28182008-08-22 02:33:23 -0400608 char *mtype = "";
Alan Cox963e4972008-07-24 17:16:06 +0100609 char mbuf[8];
610 char *cbl = "(40 wire cable)";
611
612 static const char *types[5] = {
Jean Delvare1c30c022011-07-04 15:33:24 +0200613 "RAID0", "RAID1", "RAID 0+1", "JBOD", "DISK"
Alan Cox963e4972008-07-24 17:16:06 +0100614 };
615
616 if (buf[52] > 4) /* No Disk */
617 return;
618
Jeff Garzik4fca3772011-02-15 01:13:24 -0500619 ata_id_c_string((u16 *)buf, id, 0, 41);
Alan Cox963e4972008-07-24 17:16:06 +0100620
621 if (buf[51]) {
622 mode = ffs(buf[51]);
623 mtype = "UDMA";
624 } else if (buf[49]) {
625 mode = ffs(buf[49]);
626 mtype = "MWDMA";
627 }
628
629 if (buf[76])
630 cbl = "";
631
632 if (mode)
633 snprintf(mbuf, 8, "%5s%d", mtype, mode - 1);
634 else
635 strcpy(mbuf, "PIO");
636 if (buf[52] == 4)
637 printk(KERN_INFO "%d: %-6s %-8s %s %s\n",
638 n, mbuf, types[buf[52]], id, cbl);
639 else
640 printk(KERN_INFO "%d: %-6s %-8s Volume: %1d %s %s\n",
641 n, mbuf, types[buf[52]], buf[53], id, cbl);
642 if (buf[125] < 100)
643 printk(KERN_INFO "%d: Rebuilding: %d%%\n", n, buf[125]);
644}
645
646/**
647 * it821x_firmware_command - issue firmware command
648 * @ap: IT821x port to interrogate
649 * @cmd: command
650 * @len: length
651 *
652 * Issue firmware commands expecting data back from the controller. We
653 * use this to issue commands that do not go via the normal paths. Other
654 * commands such as 0xFC can be issued normally.
655 */
656
657static u8 *it821x_firmware_command(struct ata_port *ap, u8 cmd, int len)
658{
659 u8 status;
660 int n = 0;
661 u16 *buf = kmalloc(len, GFP_KERNEL);
662 if (buf == NULL) {
663 printk(KERN_ERR "it821x_firmware_command: Out of memory\n");
664 return NULL;
665 }
666 /* This isn't quite a normal ATA command as we are talking to the
667 firmware not the drives */
668 ap->ctl |= ATA_NIEN;
669 iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
670 ata_wait_idle(ap);
671 iowrite8(ATA_DEVICE_OBS, ap->ioaddr.device_addr);
672 iowrite8(cmd, ap->ioaddr.command_addr);
673 udelay(1);
674 /* This should be almost immediate but a little paranoia goes a long
675 way. */
676 while(n++ < 10) {
677 status = ioread8(ap->ioaddr.status_addr);
678 if (status & ATA_ERR) {
679 kfree(buf);
680 printk(KERN_ERR "it821x_firmware_command: rejected\n");
681 return NULL;
682 }
683 if (status & ATA_DRQ) {
684 ioread16_rep(ap->ioaddr.data_addr, buf, len/2);
685 return (u8 *)buf;
686 }
687 mdelay(1);
688 }
689 kfree(buf);
690 printk(KERN_ERR "it821x_firmware_command: timeout\n");
691 return NULL;
692}
693
694/**
695 * it821x_probe_firmware - firmware reporting/setup
696 * @ap: IT821x port being probed
697 *
698 * Probe the firmware of the controller by issuing firmware command
699 * 0xFA and analysing the returned data.
700 */
701
702static void it821x_probe_firmware(struct ata_port *ap)
703{
704 u8 *buf;
705 int i;
706
707 /* This is a bit ugly as we can't just issue a task file to a device
708 as this is controller magic */
709
710 buf = it821x_firmware_command(ap, 0xFA, 512);
711
712 if (buf != NULL) {
713 printk(KERN_INFO "pata_it821x: Firmware %02X/%02X/%02X%02X\n",
714 buf[505],
715 buf[506],
716 buf[507],
717 buf[508]);
718 for (i = 0; i < 4; i++)
719 it821x_display_disk(i, buf + 128 * i);
720 kfree(buf);
721 }
722}
723
724
Jeff Garzik669a5db2006-08-29 18:12:40 -0400725
726/**
727 * it821x_port_start - port setup
728 * @ap: ATA port being set up
729 *
730 * The it821x needs to maintain private data structures and also to
731 * use the standard PCI interface which lacks support for this
Jeff Garzik85cd7252006-08-31 00:03:49 -0400732 * functionality. We instead set up the private data on the port
Jeff Garzik669a5db2006-08-29 18:12:40 -0400733 * start hook, and tear it down on port stop
734 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400735
Jeff Garzik669a5db2006-08-29 18:12:40 -0400736static int it821x_port_start(struct ata_port *ap)
737{
738 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
739 struct it821x_dev *itdev;
740 u8 conf;
741
Tejun Heoc7087652010-05-10 21:41:34 +0200742 int ret = ata_bmdma_port_start(ap);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400743 if (ret < 0)
744 return ret;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400745
Tejun Heo24dc5f32007-01-20 16:00:28 +0900746 itdev = devm_kzalloc(&pdev->dev, sizeof(struct it821x_dev), GFP_KERNEL);
747 if (itdev == NULL)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400748 return -ENOMEM;
Tejun Heo24dc5f32007-01-20 16:00:28 +0900749 ap->private_data = itdev;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400750
751 pci_read_config_byte(pdev, 0x50, &conf);
752
753 if (conf & 1) {
754 itdev->smart = 1;
755 /* Long I/O's although allowed in LBA48 space cause the
756 onboard firmware to enter the twighlight zone */
757 /* No ATAPI DMA in this mode either */
Alan Cox963e4972008-07-24 17:16:06 +0100758 if (ap->port_no == 0)
759 it821x_probe_firmware(ap);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400760 }
761 /* Pull the current clocks from 0x50 */
762 if (conf & (1 << (1 + ap->port_no)))
763 itdev->clock_mode = ATA_50;
764 else
765 itdev->clock_mode = ATA_66;
766
767 itdev->want[0][1] = ATA_ANY;
768 itdev->want[1][1] = ATA_ANY;
769 itdev->last_device = -1;
770
Alan Cox604de6e2007-08-23 20:18:55 +0100771 if (pdev->revision == 0x10) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400772 itdev->timing10 = 1;
773 /* Need to disable ATAPI DMA for this case */
774 if (!itdev->smart)
775 printk(KERN_WARNING DRV_NAME": Revision 0x10, workarounds activated.\n");
776 }
777
778 return 0;
779}
780
Alan Cox963e4972008-07-24 17:16:06 +0100781/**
782 * it821x_rdc_cable - Cable detect for RDC1010
783 * @ap: port we are checking
784 *
785 * Return the RDC1010 cable type. Unlike the IT821x we know how to do
786 * this and can do host side cable detect
787 */
788
789static int it821x_rdc_cable(struct ata_port *ap)
790{
791 u16 r40;
792 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
793
794 pci_read_config_word(pdev, 0x40, &r40);
795 if (r40 & (1 << (2 + ap->port_no)))
796 return ATA_CBL_PATA40;
797 return ATA_CBL_PATA80;
798}
799
Jeff Garzik669a5db2006-08-29 18:12:40 -0400800static struct scsi_host_template it821x_sht = {
Tejun Heo68d1d072008-03-25 12:22:49 +0900801 ATA_BMDMA_SHT(DRV_NAME),
Jeff Garzik669a5db2006-08-29 18:12:40 -0400802};
803
804static struct ata_port_operations it821x_smart_port_ops = {
Tejun Heo029cfd62008-03-25 12:22:49 +0900805 .inherits = &ata_bmdma_port_ops,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400806
Jeff Garzik669a5db2006-08-29 18:12:40 -0400807 .check_atapi_dma= it821x_check_atapi_dma,
Tejun Heo9363c382008-04-07 22:47:16 +0900808 .qc_issue = it821x_smart_qc_issue,
Jeff Garzikbda30282006-09-27 05:41:13 -0400809
Alan Cox963e4972008-07-24 17:16:06 +0100810 .cable_detect = ata_cable_80wire,
Tejun Heo029cfd62008-03-25 12:22:49 +0900811 .set_mode = it821x_smart_set_mode,
812 .dev_config = it821x_dev_config,
Alan Cox963e4972008-07-24 17:16:06 +0100813 .read_id = it821x_read_id,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400814
815 .port_start = it821x_port_start,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400816};
Jeff Garzik669a5db2006-08-29 18:12:40 -0400817
818static struct ata_port_operations it821x_passthru_port_ops = {
Tejun Heo029cfd62008-03-25 12:22:49 +0900819 .inherits = &ata_bmdma_port_ops,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400820
Jeff Garzik669a5db2006-08-29 18:12:40 -0400821 .check_atapi_dma= it821x_check_atapi_dma,
Tejun Heo5682ed32008-04-07 22:47:16 +0900822 .sff_dev_select = it821x_passthru_dev_select,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400823 .bmdma_start = it821x_passthru_bmdma_start,
824 .bmdma_stop = it821x_passthru_bmdma_stop,
Tejun Heo9363c382008-04-07 22:47:16 +0900825 .qc_issue = it821x_passthru_qc_issue,
Jeff Garzikbda30282006-09-27 05:41:13 -0400826
Tejun Heo029cfd62008-03-25 12:22:49 +0900827 .cable_detect = ata_cable_unknown,
828 .set_piomode = it821x_passthru_set_piomode,
829 .set_dmamode = it821x_passthru_set_dmamode,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400830
831 .port_start = it821x_port_start,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400832};
Jeff Garzik669a5db2006-08-29 18:12:40 -0400833
Alan Cox963e4972008-07-24 17:16:06 +0100834static struct ata_port_operations it821x_rdc_port_ops = {
835 .inherits = &ata_bmdma_port_ops,
836
837 .check_atapi_dma= it821x_check_atapi_dma,
838 .sff_dev_select = it821x_passthru_dev_select,
839 .bmdma_start = it821x_passthru_bmdma_start,
840 .bmdma_stop = it821x_passthru_bmdma_stop,
841 .qc_issue = it821x_passthru_qc_issue,
842
843 .cable_detect = it821x_rdc_cable,
844 .set_piomode = it821x_passthru_set_piomode,
845 .set_dmamode = it821x_passthru_set_dmamode,
846
847 .port_start = it821x_port_start,
848};
849
Randy Dunlap112cc2b2007-06-25 10:42:22 -0700850static void it821x_disable_raid(struct pci_dev *pdev)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400851{
Alan Cox963e4972008-07-24 17:16:06 +0100852 /* Neither the RDC nor the IT8211 */
853 if (pdev->vendor != PCI_VENDOR_ID_ITE ||
854 pdev->device != PCI_DEVICE_ID_ITE_8212)
855 return;
856
Jeff Garzik669a5db2006-08-29 18:12:40 -0400857 /* Reset local CPU, and set BIOS not ready */
858 pci_write_config_byte(pdev, 0x5E, 0x01);
859
860 /* Set to bypass mode, and reset PCI bus */
861 pci_write_config_byte(pdev, 0x50, 0x00);
862 pci_write_config_word(pdev, PCI_COMMAND,
863 PCI_COMMAND_PARITY | PCI_COMMAND_IO |
864 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
865 pci_write_config_word(pdev, 0x40, 0xA0F3);
866
867 pci_write_config_dword(pdev,0x4C, 0x02040204);
868 pci_write_config_byte(pdev, 0x42, 0x36);
869 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x20);
870}
871
Jeff Garzik85cd7252006-08-31 00:03:49 -0400872
Jeff Garzik669a5db2006-08-29 18:12:40 -0400873static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
874{
875 u8 conf;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400876
Tejun Heo1626aeb2007-05-04 12:43:58 +0200877 static const struct ata_port_info info_smart = {
Jeff Garzik1d2808f2007-05-28 06:59:48 -0400878 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100879 .pio_mask = ATA_PIO4,
880 .mwdma_mask = ATA_MWDMA2,
Alan Cox963e4972008-07-24 17:16:06 +0100881 .udma_mask = ATA_UDMA6,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400882 .port_ops = &it821x_smart_port_ops
883 };
Tejun Heo1626aeb2007-05-04 12:43:58 +0200884 static const struct ata_port_info info_passthru = {
Jeff Garzik1d2808f2007-05-28 06:59:48 -0400885 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100886 .pio_mask = ATA_PIO4,
887 .mwdma_mask = ATA_MWDMA2,
Jeff Garzikbf6263a2007-07-09 12:16:50 -0400888 .udma_mask = ATA_UDMA6,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400889 .port_ops = &it821x_passthru_port_ops
890 };
Alan Cox963e4972008-07-24 17:16:06 +0100891 static const struct ata_port_info info_rdc = {
892 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100893 .pio_mask = ATA_PIO4,
894 .mwdma_mask = ATA_MWDMA2,
Alan Cox4a99d952009-01-11 19:51:08 +0000895 .udma_mask = ATA_UDMA6,
896 .port_ops = &it821x_rdc_port_ops
897 };
898 static const struct ata_port_info info_rdc_11 = {
899 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100900 .pio_mask = ATA_PIO4,
901 .mwdma_mask = ATA_MWDMA2,
Alan Cox963e4972008-07-24 17:16:06 +0100902 /* No UDMA */
903 .port_ops = &it821x_rdc_port_ops
904 };
Jeff Garzik85cd7252006-08-31 00:03:49 -0400905
Tejun Heo1626aeb2007-05-04 12:43:58 +0200906 const struct ata_port_info *ppi[] = { NULL, NULL };
Jeff Garzik669a5db2006-08-29 18:12:40 -0400907 static char *mode[2] = { "pass through", "smart" };
Tejun Heof08048e2008-03-25 12:22:47 +0900908 int rc;
909
910 rc = pcim_enable_device(pdev);
911 if (rc)
912 return rc;
Jeff Garzik4fca3772011-02-15 01:13:24 -0500913
Alan Cox963e4972008-07-24 17:16:06 +0100914 if (pdev->vendor == PCI_VENDOR_ID_RDC) {
Alan Cox4a99d952009-01-11 19:51:08 +0000915 /* Deal with Vortex86SX */
916 if (pdev->revision == 0x11)
917 ppi[0] = &info_rdc_11;
918 else
919 ppi[0] = &info_rdc;
Alan Cox963e4972008-07-24 17:16:06 +0100920 } else {
921 /* Force the card into bypass mode if so requested */
922 if (it8212_noraid) {
923 printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
924 it821x_disable_raid(pdev);
925 }
926 pci_read_config_byte(pdev, 0x50, &conf);
927 conf &= 1;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400928
Alan Cox963e4972008-07-24 17:16:06 +0100929 printk(KERN_INFO DRV_NAME": controller in %s mode.\n",
930 mode[conf]);
931 if (conf == 0)
932 ppi[0] = &info_passthru;
933 else
934 ppi[0] = &info_smart;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400935 }
Tejun Heo1c5afdf2010-05-19 22:10:22 +0200936 return ata_pci_bmdma_init_one(pdev, ppi, &it821x_sht, NULL, 0);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400937}
938
Tejun Heo438ac6d2007-03-02 17:31:26 +0900939#ifdef CONFIG_PM
Alanf535d532006-11-27 16:14:36 +0000940static int it821x_reinit_one(struct pci_dev *pdev)
941{
Tejun Heof08048e2008-03-25 12:22:47 +0900942 struct ata_host *host = dev_get_drvdata(&pdev->dev);
943 int rc;
944
945 rc = ata_pci_device_do_resume(pdev);
946 if (rc)
947 return rc;
Alanf535d532006-11-27 16:14:36 +0000948 /* Resume - turn raid back off if need be */
949 if (it8212_noraid)
950 it821x_disable_raid(pdev);
Tejun Heof08048e2008-03-25 12:22:47 +0900951 ata_host_resume(host);
952 return rc;
Alanf535d532006-11-27 16:14:36 +0000953}
Tejun Heo438ac6d2007-03-02 17:31:26 +0900954#endif
Alanf535d532006-11-27 16:14:36 +0000955
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400956static const struct pci_device_id it821x[] = {
957 { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), },
958 { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), },
Otavio Salvador4192be62009-11-17 11:11:16 -0200959 { PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), },
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400960
961 { },
Jeff Garzik669a5db2006-08-29 18:12:40 -0400962};
963
964static struct pci_driver it821x_pci_driver = {
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400965 .name = DRV_NAME,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400966 .id_table = it821x,
967 .probe = it821x_init_one,
Alanf535d532006-11-27 16:14:36 +0000968 .remove = ata_pci_remove_one,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900969#ifdef CONFIG_PM
Alanf535d532006-11-27 16:14:36 +0000970 .suspend = ata_pci_device_suspend,
971 .resume = it821x_reinit_one,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900972#endif
Jeff Garzik669a5db2006-08-29 18:12:40 -0400973};
974
975static int __init it821x_init(void)
976{
977 return pci_register_driver(&it821x_pci_driver);
978}
979
Jeff Garzik669a5db2006-08-29 18:12:40 -0400980static void __exit it821x_exit(void)
981{
982 pci_unregister_driver(&it821x_pci_driver);
983}
984
Jeff Garzik669a5db2006-08-29 18:12:40 -0400985MODULE_AUTHOR("Alan Cox");
986MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller");
987MODULE_LICENSE("GPL");
988MODULE_DEVICE_TABLE(pci, it821x);
989MODULE_VERSION(DRV_VERSION);
990
991
992module_param_named(noraid, it8212_noraid, int, S_IRUGO);
Stas Sergeev5fe675e2007-06-20 22:42:13 +0400993MODULE_PARM_DESC(noraid, "Force card into bypass mode");
Jeff Garzik669a5db2006-08-29 18:12:40 -0400994
995module_init(it821x_init);
996module_exit(it821x_exit);