blob: ac1ec54e4fd50eea60d123004fe735636518722c [file] [log] [blame]
Sebastian Andrzej Siewior04bea682011-01-24 09:58:55 +05301#include <linux/kernel.h>
2#include <linux/of_pci.h>
Sebastian Andrzej Siewior96e0a072011-02-22 21:07:42 +01003#include <linux/of_irq.h>
Sebastian Andrzej Siewior04bea682011-01-24 09:58:55 +05304#include <asm/prom.h>
5
6/**
7 * of_irq_map_pci - Resolve the interrupt for a PCI device
8 * @pdev: the device whose interrupt is to be resolved
9 * @out_irq: structure of_irq filled by this function
10 *
11 * This function resolves the PCI interrupt for a given PCI device. If a
12 * device-node exists for a given pci_dev, it will use normal OF tree
13 * walking. If not, it will implement standard swizzling and walk up the
14 * PCI tree until an device-node is found, at which point it will finish
15 * resolving using the OF tree walking.
16 */
17int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq)
18{
19 struct device_node *dn, *ppnode;
20 struct pci_dev *ppdev;
21 u32 lspec;
22 __be32 lspec_be;
23 __be32 laddr[3];
24 u8 pin;
25 int rc;
26
27 /* Check if we have a device node, if yes, fallback to standard
28 * device tree parsing
29 */
30 dn = pci_device_to_OF_node(pdev);
31 if (dn) {
32 rc = of_irq_map_one(dn, 0, out_irq);
33 if (!rc)
34 return rc;
35 }
36
37 /* Ok, we don't, time to have fun. Let's start by building up an
38 * interrupt spec. we assume #interrupt-cells is 1, which is standard
39 * for PCI. If you do different, then don't use that routine.
40 */
41 rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin);
42 if (rc != 0)
43 return rc;
44 /* No pin, exit */
45 if (pin == 0)
46 return -ENODEV;
47
48 /* Now we walk up the PCI tree */
49 lspec = pin;
50 for (;;) {
51 /* Get the pci_dev of our parent */
52 ppdev = pdev->bus->self;
53
54 /* Ouch, it's a host bridge... */
55 if (ppdev == NULL) {
56 ppnode = pci_bus_to_OF_node(pdev->bus);
57
58 /* No node for host bridge ? give up */
59 if (ppnode == NULL)
60 return -EINVAL;
61 } else {
62 /* We found a P2P bridge, check if it has a node */
63 ppnode = pci_device_to_OF_node(ppdev);
64 }
65
66 /* Ok, we have found a parent with a device-node, hand over to
67 * the OF parsing code.
68 * We build a unit address from the linux device to be used for
69 * resolution. Note that we use the linux bus number which may
70 * not match your firmware bus numbering.
71 * Fortunately, in most cases, interrupt-map-mask doesn't
72 * include the bus number as part of the matching.
73 * You should still be careful about that though if you intend
74 * to rely on this function (you ship a firmware that doesn't
75 * create device nodes for all PCI devices).
76 */
77 if (ppnode)
78 break;
79
80 /* We can only get here if we hit a P2P bridge with no node,
81 * let's do standard swizzling and try again
82 */
83 lspec = pci_swizzle_interrupt_pin(pdev, lspec);
84 pdev = ppdev;
85 }
86
87 lspec_be = cpu_to_be32(lspec);
88 laddr[0] = cpu_to_be32((pdev->bus->number << 16) | (pdev->devfn << 8));
89 laddr[1] = laddr[2] = cpu_to_be32(0);
90 return of_irq_map_raw(ppnode, &lspec_be, 1, laddr, out_irq);
91}
92EXPORT_SYMBOL_GPL(of_irq_map_pci);