blob: 89dc88a171af812f1ee01f6b5b64af4e61fc7ca1 [file] [log] [blame]
Donghwa Lee7258cc12012-02-08 12:47:39 -08001/* include/video/exynos_mipi_dsim.h
2 *
3 * Platform data header for Samsung SoC MIPI-DSIM.
4 *
5 * Copyright (c) 2012 Samsung Electronics Co., Ltd
6 *
7 * InKi Dae <inki.dae@samsung.com>
8 * Donghwa Lee <dh09.lee@samsung.com>
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
13*/
14
15#ifndef _EXYNOS_MIPI_DSIM_H
16#define _EXYNOS_MIPI_DSIM_H
17
18#include <linux/device.h>
19#include <linux/fb.h>
20
21#define PANEL_NAME_SIZE (32)
22
23/*
24 * Enumerate display interface type.
25 *
26 * DSIM_COMMAND means cpu interface and rgb interface for DSIM_VIDEO.
27 *
28 * P.S. MIPI DSI Master has two display controller intefaces, RGB Interface
29 * for main display and CPU Interface(same as I80 Interface) for main
30 * and sub display.
31 */
32enum mipi_dsim_interface_type {
33 DSIM_COMMAND,
34 DSIM_VIDEO
35};
36
37enum mipi_dsim_virtual_ch_no {
38 DSIM_VIRTUAL_CH_0,
39 DSIM_VIRTUAL_CH_1,
40 DSIM_VIRTUAL_CH_2,
41 DSIM_VIRTUAL_CH_3
42};
43
44enum mipi_dsim_burst_mode_type {
45 DSIM_NON_BURST_SYNC_EVENT,
46 DSIM_BURST_SYNC_EVENT,
47 DSIM_NON_BURST_SYNC_PULSE,
48 DSIM_BURST,
49 DSIM_NON_VIDEO_MODE
50};
51
52enum mipi_dsim_no_of_data_lane {
53 DSIM_DATA_LANE_1,
54 DSIM_DATA_LANE_2,
55 DSIM_DATA_LANE_3,
56 DSIM_DATA_LANE_4
57};
58
59enum mipi_dsim_byte_clk_src {
60 DSIM_PLL_OUT_DIV8,
61 DSIM_EXT_CLK_DIV8,
62 DSIM_EXT_CLK_BYPASS
63};
64
65enum mipi_dsim_pixel_format {
66 DSIM_CMD_3BPP,
67 DSIM_CMD_8BPP,
68 DSIM_CMD_12BPP,
69 DSIM_CMD_16BPP,
70 DSIM_VID_16BPP_565,
71 DSIM_VID_18BPP_666PACKED,
72 DSIM_18BPP_666LOOSELYPACKED,
73 DSIM_24BPP_888
74};
75
76/*
77 * struct mipi_dsim_config - interface for configuring mipi-dsi controller.
78 *
79 * @auto_flush: enable or disable Auto flush of MD FIFO using VSYNC pulse.
80 * @eot_disable: enable or disable EoT packet in HS mode.
81 * @auto_vertical_cnt: specifies auto vertical count mode.
82 * in Video mode, the vertical line transition uses line counter
83 * configured by VSA, VBP, and Vertical resolution.
84 * If this bit is set to '1', the line counter does not use VSA and VBP
85 * registers.(in command mode, this variable is ignored)
86 * @hse: set horizontal sync event mode.
87 * In VSYNC pulse and Vporch area, MIPI DSI master transfers only HSYNC
88 * start packet to MIPI DSI slave at MIPI DSI spec1.1r02.
89 * this bit transfers HSYNC end packet in VSYNC pulse and Vporch area
90 * (in mommand mode, this variable is ignored)
91 * @hfp: specifies HFP disable mode.
92 * if this variable is set, DSI master ignores HFP area in VIDEO mode.
93 * (in command mode, this variable is ignored)
94 * @hbp: specifies HBP disable mode.
95 * if this variable is set, DSI master ignores HBP area in VIDEO mode.
96 * (in command mode, this variable is ignored)
97 * @hsa: specifies HSA disable mode.
98 * if this variable is set, DSI master ignores HSA area in VIDEO mode.
99 * (in command mode, this variable is ignored)
100 * @cma_allow: specifies the number of horizontal lines, where command packet
101 * transmission is allowed after Stable VFP period.
102 * @e_interface: specifies interface to be used.(CPU or RGB interface)
103 * @e_virtual_ch: specifies virtual channel number that main or
104 * sub diaplsy uses.
105 * @e_pixel_format: specifies pixel stream format for main or sub display.
106 * @e_burst_mode: selects Burst mode in Video mode.
107 * in Non-burst mode, RGB data area is filled with RGB data and NULL
108 * packets, according to input bandwidth of RGB interface.
109 * In Burst mode, RGB data area is filled with RGB data only.
110 * @e_no_data_lane: specifies data lane count to be used by Master.
111 * @e_byte_clk: select byte clock source. (it must be DSIM_PLL_OUT_DIV8)
112 * DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported.
113 * @pll_stable_time: specifies the PLL Timer for stability of the ganerated
114 * clock(System clock cycle base)
115 * if the timer value goes to 0x00000000, the clock stable bit of status
116 * and interrupt register is set.
117 * @esc_clk: specifies escape clock frequency for getting the escape clock
118 * prescaler value.
119 * @stop_holding_cnt: specifies the interval value between transmitting
120 * read packet(or write "set_tear_on" command) and BTA request.
121 * after transmitting read packet or write "set_tear_on" command,
122 * BTA requests to D-PHY automatically. this counter value specifies
123 * the interval between them.
124 * @bta_timeout: specifies the timer for BTA.
125 * this register specifies time out from BTA request to change
126 * the direction with respect to Tx escape clock.
127 * @rx_timeout: specifies the timer for LP Rx mode timeout.
128 * this register specifies time out on how long RxValid deasserts,
129 * after RxLpdt asserts with respect to Tx escape clock.
130 * - RxValid specifies Rx data valid indicator.
131 * - RxLpdt specifies an indicator that D-PHY is under RxLpdt mode.
132 * - RxValid and RxLpdt specifies signal from D-PHY.
133 */
134struct mipi_dsim_config {
135 unsigned char auto_flush;
136 unsigned char eot_disable;
137
138 unsigned char auto_vertical_cnt;
139 unsigned char hse;
140 unsigned char hfp;
141 unsigned char hbp;
142 unsigned char hsa;
143 unsigned char cmd_allow;
144
145 enum mipi_dsim_interface_type e_interface;
146 enum mipi_dsim_virtual_ch_no e_virtual_ch;
147 enum mipi_dsim_pixel_format e_pixel_format;
148 enum mipi_dsim_burst_mode_type e_burst_mode;
149 enum mipi_dsim_no_of_data_lane e_no_data_lane;
150 enum mipi_dsim_byte_clk_src e_byte_clk;
151
152 /*
153 * ===========================================
154 * | P | M | S | MHz |
155 * -------------------------------------------
156 * | 3 | 100 | 3 | 100 |
157 * | 3 | 100 | 2 | 200 |
158 * | 3 | 63 | 1 | 252 |
159 * | 4 | 100 | 1 | 300 |
160 * | 4 | 110 | 1 | 330 |
161 * | 12 | 350 | 1 | 350 |
162 * | 3 | 100 | 1 | 400 |
163 * | 4 | 150 | 1 | 450 |
164 * | 6 | 118 | 1 | 472 |
165 * | 3 | 120 | 1 | 480 |
166 * | 12 | 250 | 0 | 500 |
167 * | 4 | 100 | 0 | 600 |
168 * | 3 | 81 | 0 | 648 |
169 * | 3 | 88 | 0 | 704 |
170 * | 3 | 90 | 0 | 720 |
171 * | 3 | 100 | 0 | 800 |
172 * | 12 | 425 | 0 | 850 |
173 * | 4 | 150 | 0 | 900 |
174 * | 12 | 475 | 0 | 950 |
175 * | 6 | 250 | 0 | 1000 |
176 * -------------------------------------------
177 */
178
179 /*
180 * pms could be calculated as the following.
181 * M * 24 / P * 2 ^ S = MHz
182 */
183 unsigned char p;
184 unsigned short m;
185 unsigned char s;
186
187 unsigned int pll_stable_time;
188 unsigned long esc_clk;
189
190 unsigned short stop_holding_cnt;
191 unsigned char bta_timeout;
192 unsigned short rx_timeout;
193};
194
195/*
196 * struct mipi_dsim_device - global interface for mipi-dsi driver.
197 *
198 * @dev: driver model representation of the device.
199 * @id: unique device id.
200 * @clock: pointer to MIPI-DSI clock of clock framework.
201 * @irq: interrupt number to MIPI-DSI controller.
202 * @reg_base: base address to memory mapped SRF of MIPI-DSI controller.
203 * (virtual address)
204 * @lock: the mutex protecting this data structure.
205 * @dsim_info: infomation for configuring mipi-dsi controller.
206 * @master_ops: callbacks to mipi-dsi operations.
207 * @dsim_lcd_dev: pointer to activated ddi device.
208 * (it would be registered by mipi-dsi driver.)
209 * @dsim_lcd_drv: pointer to activated_ddi driver.
210 * (it would be registered by mipi-dsi driver.)
211 * @lcd_info: pointer to mipi_lcd_info structure.
212 * @state: specifies status of MIPI-DSI controller.
213 * the status could be RESET, INIT, STOP, HSCLKEN and ULPS.
214 * @data_lane: specifiec enabled data lane number.
215 * this variable would be set by driver according to e_no_data_lane
216 * automatically.
217 * @e_clk_src: select byte clock source.
218 * @pd: pointer to MIPI-DSI driver platform data.
219 */
220struct mipi_dsim_device {
221 struct device *dev;
222 int id;
Donghwa Lee7258cc12012-02-08 12:47:39 -0800223 struct clk *clock;
224 unsigned int irq;
225 void __iomem *reg_base;
226 struct mutex lock;
227
228 struct mipi_dsim_config *dsim_config;
229 struct mipi_dsim_master_ops *master_ops;
230 struct mipi_dsim_lcd_device *dsim_lcd_dev;
231 struct mipi_dsim_lcd_driver *dsim_lcd_drv;
232
233 unsigned int state;
234 unsigned int data_lane;
235 unsigned int e_clk_src;
236 bool suspended;
237
238 struct mipi_dsim_platform_data *pd;
239};
240
241/*
242 * struct mipi_dsim_platform_data - interface to platform data
243 * for mipi-dsi driver.
244 *
245 * @lcd_panel_name: specifies lcd panel name registered to mipi-dsi driver.
246 * lcd panel driver searched would be actived.
247 * @dsim_config: pointer of structure for configuring mipi-dsi controller.
248 * @enabled: indicate whether mipi controller got enabled or not.
249 * @lcd_panel_info: pointer for lcd panel specific structure.
250 * this structure specifies width, height, timing and polarity and so on.
251 * @phy_enable: pointer to a callback controlling D-PHY enable/reset
252 */
253struct mipi_dsim_platform_data {
254 char lcd_panel_name[PANEL_NAME_SIZE];
255
256 struct mipi_dsim_config *dsim_config;
257 unsigned int enabled;
258 void *lcd_panel_info;
259
260 int (*phy_enable)(struct platform_device *pdev, bool on);
261};
262
263/*
264 * struct mipi_dsim_master_ops - callbacks to mipi-dsi operations.
265 *
266 * @cmd_write: transfer command to lcd panel at LP mode.
267 * @cmd_read: read command from rx register.
268 * @get_dsim_frame_done: get the status that all screen data have been
269 * transferred to mipi-dsi.
270 * @clear_dsim_frame_done: clear frame done status.
271 * @get_fb_frame_done: get frame done status of display controller.
272 * @trigger: trigger display controller.
273 * - this one would be used only in case of CPU mode.
274 * @set_early_blank_mode: set framebuffer blank mode.
275 * - this callback should be called prior to fb_blank() by a client driver
276 * only if needing.
277 * @set_blank_mode: set framebuffer blank mode.
278 * - this callback should be called after fb_blank() by a client driver
279 * only if needing.
280 */
281
282struct mipi_dsim_master_ops {
283 int (*cmd_write)(struct mipi_dsim_device *dsim, unsigned int data_id,
284 const unsigned char *data0, unsigned int data1);
285 int (*cmd_read)(struct mipi_dsim_device *dsim, unsigned int data_id,
286 unsigned int data0, unsigned int req_size, u8 *rx_buf);
287 int (*get_dsim_frame_done)(struct mipi_dsim_device *dsim);
288 int (*clear_dsim_frame_done)(struct mipi_dsim_device *dsim);
289
290 int (*get_fb_frame_done)(struct fb_info *info);
291 void (*trigger)(struct fb_info *info);
292 int (*set_early_blank_mode)(struct mipi_dsim_device *dsim, int power);
293 int (*set_blank_mode)(struct mipi_dsim_device *dsim, int power);
294};
295
296/*
297 * device structure for mipi-dsi based lcd panel.
298 *
299 * @name: name of the device to use with this device, or an
300 * alias for that name.
301 * @dev: driver model representation of the device.
302 * @id: id of device to be registered.
303 * @bus_id: bus id for identifing connected bus
304 * and this bus id should be same as id of mipi_dsim_device.
305 * @irq: irq number for signaling when framebuffer transfer of
306 * lcd panel module is completed.
307 * this irq would be used only for MIPI-DSI based CPU mode lcd panel.
308 * @master: pointer to mipi-dsi master device object.
309 * @platform_data: lcd panel specific platform data.
310 */
311struct mipi_dsim_lcd_device {
312 char *name;
313 struct device dev;
314 int id;
315 int bus_id;
316 int irq;
Donghwa Lee24bb7a6e2012-05-09 14:33:31 +0900317 int panel_reverse;
Donghwa Lee7258cc12012-02-08 12:47:39 -0800318
319 struct mipi_dsim_device *master;
320 void *platform_data;
321};
322
323/*
324 * driver structure for mipi-dsi based lcd panel.
325 *
326 * this structure should be registered by lcd panel driver.
327 * mipi-dsi driver seeks lcd panel registered through name field
328 * and calls these callback functions in appropriate time.
329 *
330 * @name: name of the driver to use with this device, or an
331 * alias for that name.
332 * @id: id of driver to be registered.
333 * this id would be used for finding device object registered.
334 */
335struct mipi_dsim_lcd_driver {
336 char *name;
337 int id;
338
339 void (*power_on)(struct mipi_dsim_lcd_device *dsim_dev, int enable);
340 void (*set_sequence)(struct mipi_dsim_lcd_device *dsim_dev);
341 int (*probe)(struct mipi_dsim_lcd_device *dsim_dev);
342 int (*remove)(struct mipi_dsim_lcd_device *dsim_dev);
343 void (*shutdown)(struct mipi_dsim_lcd_device *dsim_dev);
344 int (*suspend)(struct mipi_dsim_lcd_device *dsim_dev);
345 int (*resume)(struct mipi_dsim_lcd_device *dsim_dev);
346};
347
348/*
349 * register mipi_dsim_lcd_device to mipi-dsi master.
350 */
351int exynos_mipi_dsi_register_lcd_device(struct mipi_dsim_lcd_device
352 *lcd_dev);
353/**
354 * register mipi_dsim_lcd_driver object defined by lcd panel driver
355 * to mipi-dsi driver.
356 */
357int exynos_mipi_dsi_register_lcd_driver(struct mipi_dsim_lcd_driver
358 *lcd_drv);
359#endif /* _EXYNOS_MIPI_DSIM_H */