blob: b29a2be245911c62cc67a3b6e6aed3864b03242b [file] [log] [blame]
Christoph Mair5bf1d292010-08-09 17:20:28 -07001/* Copyright (c) 2010 Christoph Mair <christoph.mair@gmail.com>
2
3 This driver supports the bmp085 digital barometric pressure
4 and temperature sensor from Bosch Sensortec. The datasheet
Lucas De Marchi25985ed2011-03-30 22:57:33 -03005 is available from their website:
Christoph Mair5bf1d292010-08-09 17:20:28 -07006 http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP085-DS000-05.pdf
7
8 A pressure measurement is issued by reading from pressure0_input.
9 The return value ranges from 30000 to 110000 pascal with a resulution
10 of 1 pascal (0.01 millibar) which enables measurements from 9000m above
11 to 500m below sea level.
12
13 The temperature can be read from temp0_input. Values range from
14 -400 to 850 representing the ambient temperature in degree celsius
15 multiplied by 10.The resolution is 0.1 celsius.
16
17 Because ambient pressure is temperature dependent, a temperature
18 measurement will be executed automatically even if the user is reading
19 from pressure0_input. This happens if the last temperature measurement
20 has been executed more then one second ago.
21
22 To decrease RMS noise from pressure measurements, the bmp085 can
23 autonomously calculate the average of up to eight samples. This is
24 set up by writing to the oversampling sysfs file. Accepted values
25 are 0, 1, 2 and 3. 2^x when x is the value written to this file
26 specifies the number of samples used to calculate the ambient pressure.
27 RMS noise is specified with six pascal (without averaging) and decreases
28 down to 3 pascal when using an oversampling setting of 3.
29
30 This program is free software; you can redistribute it and/or modify
31 it under the terms of the GNU General Public License as published by
32 the Free Software Foundation; either version 2 of the License, or
33 (at your option) any later version.
34
35 This program is distributed in the hope that it will be useful,
36 but WITHOUT ANY WARRANTY; without even the implied warranty of
37 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
38 GNU General Public License for more details.
39
40 You should have received a copy of the GNU General Public License
41 along with this program; if not, write to the Free Software
42 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
43*/
44
45
46#include <linux/module.h>
47#include <linux/init.h>
48#include <linux/i2c.h>
49#include <linux/slab.h>
50#include <linux/delay.h>
51
52
53#define BMP085_I2C_ADDRESS 0x77
54#define BMP085_CHIP_ID 0x55
55
56#define BMP085_CALIBRATION_DATA_START 0xAA
57#define BMP085_CALIBRATION_DATA_LENGTH 11 /* 16 bit values */
58#define BMP085_CHIP_ID_REG 0xD0
59#define BMP085_VERSION_REG 0xD1
60#define BMP085_CTRL_REG 0xF4
61#define BMP085_TEMP_MEASUREMENT 0x2E
62#define BMP085_PRESSURE_MEASUREMENT 0x34
63#define BMP085_CONVERSION_REGISTER_MSB 0xF6
64#define BMP085_CONVERSION_REGISTER_LSB 0xF7
65#define BMP085_CONVERSION_REGISTER_XLSB 0xF8
66#define BMP085_TEMP_CONVERSION_TIME 5
67
68#define BMP085_CLIENT_NAME "bmp085"
69
70
71static const unsigned short normal_i2c[] = { BMP085_I2C_ADDRESS,
72 I2C_CLIENT_END };
73
74struct bmp085_calibration_data {
75 s16 AC1, AC2, AC3;
76 u16 AC4, AC5, AC6;
77 s16 B1, B2;
78 s16 MB, MC, MD;
79};
80
81
82/* Each client has this additional data */
83struct bmp085_data {
84 struct i2c_client *client;
85 struct mutex lock;
86 struct bmp085_calibration_data calibration;
87 u32 raw_temperature;
88 u32 raw_pressure;
89 unsigned char oversampling_setting;
90 u32 last_temp_measurement;
91 s32 b6; /* calculated temperature correction coefficient */
92};
93
94
95static s32 bmp085_read_calibration_data(struct i2c_client *client)
96{
97 u16 tmp[BMP085_CALIBRATION_DATA_LENGTH];
98 struct bmp085_data *data = i2c_get_clientdata(client);
99 struct bmp085_calibration_data *cali = &(data->calibration);
100 s32 status = i2c_smbus_read_i2c_block_data(client,
101 BMP085_CALIBRATION_DATA_START,
102 BMP085_CALIBRATION_DATA_LENGTH*sizeof(u16),
103 (u8 *)tmp);
104 if (status < 0)
105 return status;
106
107 if (status != BMP085_CALIBRATION_DATA_LENGTH*sizeof(u16))
108 return -EIO;
109
110 cali->AC1 = be16_to_cpu(tmp[0]);
111 cali->AC2 = be16_to_cpu(tmp[1]);
112 cali->AC3 = be16_to_cpu(tmp[2]);
113 cali->AC4 = be16_to_cpu(tmp[3]);
114 cali->AC5 = be16_to_cpu(tmp[4]);
115 cali->AC6 = be16_to_cpu(tmp[5]);
116 cali->B1 = be16_to_cpu(tmp[6]);
117 cali->B2 = be16_to_cpu(tmp[7]);
118 cali->MB = be16_to_cpu(tmp[8]);
119 cali->MC = be16_to_cpu(tmp[9]);
120 cali->MD = be16_to_cpu(tmp[10]);
121 return 0;
122}
123
124
125static s32 bmp085_update_raw_temperature(struct bmp085_data *data)
126{
127 u16 tmp;
128 s32 status;
129
130 mutex_lock(&data->lock);
131 status = i2c_smbus_write_byte_data(data->client, BMP085_CTRL_REG,
132 BMP085_TEMP_MEASUREMENT);
133 if (status != 0) {
134 dev_err(&data->client->dev,
135 "Error while requesting temperature measurement.\n");
136 goto exit;
137 }
138 msleep(BMP085_TEMP_CONVERSION_TIME);
139
140 status = i2c_smbus_read_i2c_block_data(data->client,
141 BMP085_CONVERSION_REGISTER_MSB, sizeof(tmp), (u8 *)&tmp);
142 if (status < 0)
143 goto exit;
144 if (status != sizeof(tmp)) {
145 dev_err(&data->client->dev,
146 "Error while reading temperature measurement result\n");
147 status = -EIO;
148 goto exit;
149 }
150 data->raw_temperature = be16_to_cpu(tmp);
151 data->last_temp_measurement = jiffies;
152 status = 0; /* everything ok, return 0 */
153
154exit:
155 mutex_unlock(&data->lock);
156 return status;
157}
158
159static s32 bmp085_update_raw_pressure(struct bmp085_data *data)
160{
161 u32 tmp = 0;
162 s32 status;
163
164 mutex_lock(&data->lock);
165 status = i2c_smbus_write_byte_data(data->client, BMP085_CTRL_REG,
166 BMP085_PRESSURE_MEASUREMENT + (data->oversampling_setting<<6));
167 if (status != 0) {
168 dev_err(&data->client->dev,
169 "Error while requesting pressure measurement.\n");
170 goto exit;
171 }
172
173 /* wait for the end of conversion */
174 msleep(2+(3 << data->oversampling_setting));
175
176 /* copy data into a u32 (4 bytes), but skip the first byte. */
177 status = i2c_smbus_read_i2c_block_data(data->client,
178 BMP085_CONVERSION_REGISTER_MSB, 3, ((u8 *)&tmp)+1);
179 if (status < 0)
180 goto exit;
181 if (status != 3) {
182 dev_err(&data->client->dev,
183 "Error while reading pressure measurement results\n");
184 status = -EIO;
185 goto exit;
186 }
187 data->raw_pressure = be32_to_cpu((tmp));
188 data->raw_pressure >>= (8-data->oversampling_setting);
189 status = 0; /* everything ok, return 0 */
190
191exit:
192 mutex_unlock(&data->lock);
193 return status;
194}
195
196
197/*
198 * This function starts the temperature measurement and returns the value
199 * in tenth of a degree celsius.
200 */
201static s32 bmp085_get_temperature(struct bmp085_data *data, int *temperature)
202{
203 struct bmp085_calibration_data *cali = &data->calibration;
204 long x1, x2;
205 int status;
206
207 status = bmp085_update_raw_temperature(data);
208 if (status != 0)
209 goto exit;
210
211 x1 = ((data->raw_temperature - cali->AC6) * cali->AC5) >> 15;
212 x2 = (cali->MC << 11) / (x1 + cali->MD);
213 data->b6 = x1 + x2 - 4000;
214 /* if NULL just update b6. Used for pressure only measurements */
215 if (temperature != NULL)
216 *temperature = (x1+x2+8) >> 4;
217
218exit:
Jesper Juhlf80ea662011-12-17 23:52:27 +0100219 return status;
Christoph Mair5bf1d292010-08-09 17:20:28 -0700220}
221
222/*
223 * This function starts the pressure measurement and returns the value
224 * in millibar. Since the pressure depends on the ambient temperature,
225 * a temperature measurement is executed if the last known value is older
226 * than one second.
227 */
228static s32 bmp085_get_pressure(struct bmp085_data *data, int *pressure)
229{
230 struct bmp085_calibration_data *cali = &data->calibration;
231 s32 x1, x2, x3, b3;
232 u32 b4, b7;
233 s32 p;
234 int status;
235
236 /* alt least every second force an update of the ambient temperature */
237 if (data->last_temp_measurement + 1*HZ < jiffies) {
238 status = bmp085_get_temperature(data, NULL);
239 if (status != 0)
240 goto exit;
241 }
242
243 status = bmp085_update_raw_pressure(data);
244 if (status != 0)
245 goto exit;
246
247 x1 = (data->b6 * data->b6) >> 12;
248 x1 *= cali->B2;
249 x1 >>= 11;
250
251 x2 = cali->AC2 * data->b6;
252 x2 >>= 11;
253
254 x3 = x1 + x2;
255
256 b3 = (((((s32)cali->AC1) * 4 + x3) << data->oversampling_setting) + 2);
257 b3 >>= 2;
258
259 x1 = (cali->AC3 * data->b6) >> 13;
260 x2 = (cali->B1 * ((data->b6 * data->b6) >> 12)) >> 16;
261 x3 = (x1 + x2 + 2) >> 2;
262 b4 = (cali->AC4 * (u32)(x3 + 32768)) >> 15;
263
264 b7 = ((u32)data->raw_pressure - b3) *
265 (50000 >> data->oversampling_setting);
266 p = ((b7 < 0x80000000) ? ((b7 << 1) / b4) : ((b7 / b4) * 2));
267
268 x1 = p >> 8;
269 x1 *= x1;
270 x1 = (x1 * 3038) >> 16;
271 x2 = (-7357 * p) >> 16;
272 p += (x1 + x2 + 3791) >> 4;
273
274 *pressure = p;
275
276exit:
277 return status;
278}
279
280/*
281 * This function sets the chip-internal oversampling. Valid values are 0..3.
282 * The chip will use 2^oversampling samples for internal averaging.
283 * This influences the measurement time and the accuracy; larger values
284 * increase both. The datasheet gives on overview on how measurement time,
285 * accuracy and noise correlate.
286 */
287static void bmp085_set_oversampling(struct bmp085_data *data,
288 unsigned char oversampling)
289{
290 if (oversampling > 3)
291 oversampling = 3;
292 data->oversampling_setting = oversampling;
293}
294
295/*
296 * Returns the currently selected oversampling. Range: 0..3
297 */
298static unsigned char bmp085_get_oversampling(struct bmp085_data *data)
299{
300 return data->oversampling_setting;
301}
302
303/* sysfs callbacks */
304static ssize_t set_oversampling(struct device *dev,
305 struct device_attribute *attr,
306 const char *buf, size_t count)
307{
308 struct i2c_client *client = to_i2c_client(dev);
309 struct bmp085_data *data = i2c_get_clientdata(client);
310 unsigned long oversampling;
311 int success = strict_strtoul(buf, 10, &oversampling);
312 if (success == 0) {
313 bmp085_set_oversampling(data, oversampling);
314 return count;
315 }
316 return success;
317}
318
319static ssize_t show_oversampling(struct device *dev,
320 struct device_attribute *attr, char *buf)
321{
322 struct i2c_client *client = to_i2c_client(dev);
323 struct bmp085_data *data = i2c_get_clientdata(client);
324 return sprintf(buf, "%u\n", bmp085_get_oversampling(data));
325}
326static DEVICE_ATTR(oversampling, S_IWUSR | S_IRUGO,
327 show_oversampling, set_oversampling);
328
329
330static ssize_t show_temperature(struct device *dev,
331 struct device_attribute *attr, char *buf)
332{
333 int temperature;
334 int status;
335 struct i2c_client *client = to_i2c_client(dev);
336 struct bmp085_data *data = i2c_get_clientdata(client);
337
338 status = bmp085_get_temperature(data, &temperature);
339 if (status != 0)
340 return status;
341 else
342 return sprintf(buf, "%d\n", temperature);
343}
344static DEVICE_ATTR(temp0_input, S_IRUGO, show_temperature, NULL);
345
346
347static ssize_t show_pressure(struct device *dev,
348 struct device_attribute *attr, char *buf)
349{
350 int pressure;
351 int status;
352 struct i2c_client *client = to_i2c_client(dev);
353 struct bmp085_data *data = i2c_get_clientdata(client);
354
355 status = bmp085_get_pressure(data, &pressure);
356 if (status != 0)
357 return status;
358 else
359 return sprintf(buf, "%d\n", pressure);
360}
361static DEVICE_ATTR(pressure0_input, S_IRUGO, show_pressure, NULL);
362
363
364static struct attribute *bmp085_attributes[] = {
365 &dev_attr_temp0_input.attr,
366 &dev_attr_pressure0_input.attr,
367 &dev_attr_oversampling.attr,
368 NULL
369};
370
371static const struct attribute_group bmp085_attr_group = {
372 .attrs = bmp085_attributes,
373};
374
375static int bmp085_detect(struct i2c_client *client, struct i2c_board_info *info)
376{
377 if (client->addr != BMP085_I2C_ADDRESS)
378 return -ENODEV;
379
380 if (i2c_smbus_read_byte_data(client, BMP085_CHIP_ID_REG) != BMP085_CHIP_ID)
381 return -ENODEV;
382
383 return 0;
384}
385
386static int bmp085_init_client(struct i2c_client *client)
387{
388 unsigned char version;
389 int status;
390 struct bmp085_data *data = i2c_get_clientdata(client);
391 data->client = client;
392 status = bmp085_read_calibration_data(client);
393 if (status != 0)
394 goto exit;
395 version = i2c_smbus_read_byte_data(client, BMP085_VERSION_REG);
396 data->last_temp_measurement = 0;
397 data->oversampling_setting = 3;
398 mutex_init(&data->lock);
399 dev_info(&data->client->dev, "BMP085 ver. %d.%d found.\n",
400 (version & 0x0F), (version & 0xF0) >> 4);
401exit:
402 return status;
403}
404
Shubhrajyoti Datta45bff2e2011-03-22 16:33:57 -0700405static int __devinit bmp085_probe(struct i2c_client *client,
Christoph Mair5bf1d292010-08-09 17:20:28 -0700406 const struct i2c_device_id *id)
407{
408 struct bmp085_data *data;
409 int err = 0;
410
411 data = kzalloc(sizeof(struct bmp085_data), GFP_KERNEL);
412 if (!data) {
413 err = -ENOMEM;
414 goto exit;
415 }
416
417 /* default settings after POR */
418 data->oversampling_setting = 0x00;
419
420 i2c_set_clientdata(client, data);
421
422 /* Initialize the BMP085 chip */
423 err = bmp085_init_client(client);
424 if (err != 0)
425 goto exit_free;
426
427 /* Register sysfs hooks */
428 err = sysfs_create_group(&client->dev.kobj, &bmp085_attr_group);
429 if (err)
430 goto exit_free;
431
Lucas De Marchi25985ed2011-03-30 22:57:33 -0300432 dev_info(&data->client->dev, "Successfully initialized bmp085!\n");
Christoph Mair5bf1d292010-08-09 17:20:28 -0700433 goto exit;
434
435exit_free:
436 kfree(data);
437exit:
438 return err;
439}
440
Shubhrajyoti Datta45bff2e2011-03-22 16:33:57 -0700441static int __devexit bmp085_remove(struct i2c_client *client)
Christoph Mair5bf1d292010-08-09 17:20:28 -0700442{
443 sysfs_remove_group(&client->dev.kobj, &bmp085_attr_group);
444 kfree(i2c_get_clientdata(client));
445 return 0;
446}
447
448static const struct i2c_device_id bmp085_id[] = {
449 { "bmp085", 0 },
450 { }
451};
Axel Lin97e419a2011-03-04 17:36:22 -0800452MODULE_DEVICE_TABLE(i2c, bmp085_id);
Christoph Mair5bf1d292010-08-09 17:20:28 -0700453
454static struct i2c_driver bmp085_driver = {
455 .driver = {
456 .owner = THIS_MODULE,
457 .name = "bmp085"
458 },
459 .id_table = bmp085_id,
460 .probe = bmp085_probe,
Shubhrajyoti Datta45bff2e2011-03-22 16:33:57 -0700461 .remove = __devexit_p(bmp085_remove),
Christoph Mair5bf1d292010-08-09 17:20:28 -0700462
463 .detect = bmp085_detect,
464 .address_list = normal_i2c
465};
466
467static int __init bmp085_init(void)
468{
469 return i2c_add_driver(&bmp085_driver);
470}
471
472static void __exit bmp085_exit(void)
473{
474 i2c_del_driver(&bmp085_driver);
475}
476
477
478MODULE_AUTHOR("Christoph Mair <christoph.mair@gmail.com");
479MODULE_DESCRIPTION("BMP085 driver");
480MODULE_LICENSE("GPL");
481
482module_init(bmp085_init);
483module_exit(bmp085_exit);