blob: 0df024bfd6f0c672a755b2f701711040691f95ae [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#ifndef _LINUX_LP_H
2#define _LINUX_LP_H
3
4/*
5 * usr/include/linux/lp.h c.1991-1992 James Wiegand
6 * many modifications copyright (C) 1992 Michael K. Johnson
7 * Interrupt support added 1993 Nigel Gamble
8 * Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
9 */
10
11/*
12 * Per POSIX guidelines, this module reserves the LP and lp prefixes
13 * These are the lp_table[minor].flags flags...
14 */
15#define LP_EXIST 0x0001
16#define LP_SELEC 0x0002
17#define LP_BUSY 0x0004
18#define LP_BUSY_BIT_POS 2
19#define LP_OFFL 0x0008
20#define LP_NOPA 0x0010
21#define LP_ERR 0x0020
22#define LP_ABORT 0x0040
23#define LP_CAREFUL 0x0080 /* obsoleted -arca */
24#define LP_ABORTOPEN 0x0100
25
26#define LP_TRUST_IRQ_ 0x0200 /* obsolete */
27#define LP_NO_REVERSE 0x0400 /* No reverse mode available. */
28#define LP_DATA_AVAIL 0x0800 /* Data is available. */
29
30/*
31 * bit defines for 8255 status port
32 * base + 1
33 * accessed with LP_S(minor), which gets the byte...
34 */
35#define LP_PBUSY 0x80 /* inverted input, active high */
36#define LP_PACK 0x40 /* unchanged input, active low */
37#define LP_POUTPA 0x20 /* unchanged input, active high */
38#define LP_PSELECD 0x10 /* unchanged input, active high */
39#define LP_PERRORP 0x08 /* unchanged input, active low */
40
41/* timeout for each character. This is relative to bus cycles -- it
42 * is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you
43 * have extremely slow printing, or if the machine seems to slow down
44 * a lot when you print. If you have slow printing, increase this
45 * number and recompile, and if your system gets bogged down, decrease
46 * this number. This can be changed with the tunelp(8) command as well.
47 */
48
49#define LP_INIT_CHAR 1000
50
51/* The parallel port specs apparently say that there needs to be
52 * a .5usec wait before and after the strobe.
53 */
54
55#define LP_INIT_WAIT 1
56
57/* This is the amount of time that the driver waits for the printer to
58 * catch up when the printer's buffer appears to be filled. If you
59 * want to tune this and have a fast printer (i.e. HPIIIP), decrease
60 * this number, and if you have a slow printer, increase this number.
61 * This is in hundredths of a second, the default 2 being .05 second.
62 * Or use the tunelp(8) command, which is especially nice if you want
63 * change back and forth between character and graphics printing, which
64 * are wildly different...
65 */
66
67#define LP_INIT_TIME 2
68
69/* IOCTL numbers */
70#define LPCHAR 0x0601 /* corresponds to LP_INIT_CHAR */
71#define LPTIME 0x0602 /* corresponds to LP_INIT_TIME */
72#define LPABORT 0x0604 /* call with TRUE arg to abort on error,
73 FALSE to retry. Default is retry. */
74#define LPSETIRQ 0x0605 /* call with new IRQ number,
75 or 0 for polling (no IRQ) */
76#define LPGETIRQ 0x0606 /* get the current IRQ number */
77#define LPWAIT 0x0608 /* corresponds to LP_INIT_WAIT */
78/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
79#define LPCAREFUL 0x0609 /* call with TRUE arg to require out-of-paper, off-
80 line, and error indicators good on all writes,
81 FALSE to ignore them. Default is ignore. */
82#define LPABORTOPEN 0x060a /* call with TRUE arg to abort open() on error,
83 FALSE to ignore error. Default is ignore. */
84#define LPGETSTATUS 0x060b /* return LP_S(minor) */
85#define LPRESET 0x060c /* reset printer */
86#ifdef LP_STATS
87#define LPGETSTATS 0x060d /* get statistics (struct lp_stats) */
88#endif
89#define LPGETFLAGS 0x060e /* get status flags */
90#define LPSETTIMEOUT 0x060f /* set parport timeout */
91
92/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
93 This is also used for re-checking error conditions if LP_ABORT is
94 not set. This is the default behavior. */
95
96#define LP_TIMEOUT_INTERRUPT (60 * HZ)
97#define LP_TIMEOUT_POLLED (10 * HZ)
98
99#ifdef __KERNEL__
100
101#include <linux/wait.h>
Matthias Kaehlcke0a5dcb52008-02-06 01:36:25 -0800102#include <linux/mutex.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700103
104/* Magic numbers for defining port-device mappings */
105#define LP_PARPORT_UNSPEC -4
106#define LP_PARPORT_AUTO -3
107#define LP_PARPORT_OFF -2
108#define LP_PARPORT_NONE -1
109
110#define LP_F(minor) lp_table[(minor)].flags /* flags for busy, etc. */
111#define LP_CHAR(minor) lp_table[(minor)].chars /* busy timeout */
112#define LP_TIME(minor) lp_table[(minor)].time /* wait time */
113#define LP_WAIT(minor) lp_table[(minor)].wait /* strobe wait */
114#define LP_IRQ(minor) lp_table[(minor)].dev->port->irq /* interrupt # */
115 /* PARPORT_IRQ_NONE means polled */
116#ifdef LP_STATS
117#define LP_STAT(minor) lp_table[(minor)].stats /* statistics area */
118#endif
119#define LP_BUFFER_SIZE PAGE_SIZE
120
121#define LP_BASE(x) lp_table[(x)].dev->port->base
122
123#ifdef LP_STATS
124struct lp_stats {
125 unsigned long chars;
126 unsigned long sleeps;
127 unsigned int maxrun;
128 unsigned int maxwait;
129 unsigned int meanwait;
130 unsigned int mdev;
131};
132#endif
133
134struct lp_struct {
135 struct pardevice *dev;
136 unsigned long flags;
137 unsigned int chars;
138 unsigned int time;
139 unsigned int wait;
140 char *lp_buffer;
141#ifdef LP_STATS
142 unsigned int lastcall;
143 unsigned int runchars;
144 struct lp_stats stats;
145#endif
146 wait_queue_head_t waitq;
147 unsigned int last_error;
Matthias Kaehlcke0a5dcb52008-02-06 01:36:25 -0800148 struct mutex port_mutex;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700149 wait_queue_head_t dataq;
150 long timeout;
151 unsigned int best_mode;
152 unsigned int current_mode;
153 unsigned long bits;
154};
155
156/*
157 * The following constants describe the various signals of the printer port
158 * hardware. Note that the hardware inverts some signals and that some
159 * signals are active low. An example is LP_STROBE, which must be programmed
160 * with 1 for being active and 0 for being inactive, because the strobe signal
161 * gets inverted, but it is also active low.
162 */
163
164
165/*
166 * defines for 8255 control port
167 * base + 2
168 * accessed with LP_C(minor)
169 */
170#define LP_PINTEN 0x10 /* high to read data in or-ed with data out */
171#define LP_PSELECP 0x08 /* inverted output, active low */
172#define LP_PINITP 0x04 /* unchanged output, active low */
173#define LP_PAUTOLF 0x02 /* inverted output, active low */
174#define LP_PSTROBE 0x01 /* short high output on raising edge */
175
176/*
177 * the value written to ports to test existence. PC-style ports will
178 * return the value written. AT-style ports will return 0. so why not
179 * make them the same ?
180 */
181#define LP_DUMMY 0x00
182
183/*
184 * This is the port delay time, in microseconds.
185 * It is used only in the lp_init() and lp_reset() routine.
186 */
187#define LP_DELAY 50
188
189#endif
190
191#endif