blob: 9af25b810c1f7ff0e3a76960e8b7beb463363126 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001Text File for the SMC TokenCard TokenRing Linux driver (smctr.c).
2 By Jay Schulist <jschlst@samba.org>
3
4The Linux SMC Token Ring driver works with the SMC TokenCard Elite (8115T)
5ISA and SMC TokenCard Elite/A (8115T/A) MCA adapters.
6
7Latest information on this driver can be obtained on the Linux-SNA WWW site.
8Please point your browser to: http://www.linux-sna.org
9
10This driver is rather simple to use. Select Y to Token Ring adapter support
11in the kernel configuration. A choice for SMC Token Ring adapters will
12appear. This drives supports all SMC ISA/MCA adapters. Choose this
13option. I personally recommend compiling the driver as a module (M), but if you
Matt LaPlante53cb4722006-10-03 22:55:17 +020014you would like to compile it statically answer Y instead.
Linus Torvalds1da177e2005-04-16 15:20:36 -070015
16This driver supports multiple adapters without the need to load multiple copies
17of the driver. You should be able to load up to 7 adapters without any kernel
18modifications, if you are in need of more please contact the maintainer of this
19driver.
20
21Load the driver either by lilo/loadlin or as a module. When a module using the
22following command will suffice for most:
23
24# modprobe smctr
25smctr.c: v1.00 12/6/99 by jschlst@samba.org
26tr0: SMC TokenCard 8115T at Io 0x300, Irq 10, Rom 0xd8000, Ram 0xcc000.
27
28Now just setup the device via ifconfig and set and routes you may have. After
29this you are ready to start sending some tokens.
30
31Errata:
321). For anyone wondering where to pick up the SMC adapters please browse
33 to http://www.smc.com
34
352). If you are the first/only Token Ring Client on a Token Ring LAN, please
36 specify the ringspeed with the ringspeed=[4/16] module option. If no
37 ringspeed is specified the driver will attempt to autodetect the ring
38 speed and/or if the adapter is the first/only station on the ring take
39 the appropriate actions.
40
41 NOTE: Default ring speed is 16MB UTP.
42
433). PnP support for this adapter sucks. I recommend hard setting the
44 IO/MEM/IRQ by the jumpers on the adapter. If this is not possible
45 load the module with the following io=[ioaddr] mem=[mem_addr]
46 irq=[irq_num].
47
48 The following IRQ, IO, and MEM settings are supported.
49
50 IO ports:
51 0x200, 0x220, 0x240, 0x260, 0x280, 0x2A0, 0x2C0, 0x2E0, 0x300,
52 0x320, 0x340, 0x360, 0x380.
53
54 IRQs:
55 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13, 14, 15
56
57 Memory addresses:
58 0xA0000, 0xA4000, 0xA8000, 0xAC000, 0xB0000, 0xB4000,
59 0xB8000, 0xBC000, 0xC0000, 0xC4000, 0xC8000, 0xCC000,
60 0xD0000, 0xD4000, 0xD8000, 0xDC000, 0xE0000, 0xE4000,
61 0xE8000, 0xEC000, 0xF0000, 0xF4000, 0xF8000, 0xFC000
62
63This driver is under the GNU General Public License. Its Firmware image is
64included as an initialized C-array and is licensed by SMC to the Linux
65users of this driver. However no warranty about its fitness is expressed or
66implied by SMC.