blob: 62e9ebf967f9943ff7eacbad14e6b72900620a07 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * ti113x.h 1.16 1999/10/25 20:03:34
3 *
4 * The contents of this file are subject to the Mozilla Public License
5 * Version 1.1 (the "License"); you may not use this file except in
6 * compliance with the License. You may obtain a copy of the License
7 * at http://www.mozilla.org/MPL/
8 *
9 * Software distributed under the License is distributed on an "AS IS"
10 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
11 * the License for the specific language governing rights and
12 * limitations under the License.
13 *
14 * The initial developer of the original code is David A. Hinds
15 * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
16 * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
17 *
18 * Alternatively, the contents of this file may be used under the
19 * terms of the GNU General Public License version 2 (the "GPL"), in which
20 * case the provisions of the GPL are applicable instead of the
21 * above. If you wish to allow the use of your version of this file
22 * only under the terms of the GPL and not to allow others to use
23 * your version of this file under the MPL, indicate your decision by
24 * deleting the provisions above and replace them with the notice and
25 * other provisions required by the GPL. If you do not delete the
26 * provisions above, a recipient may use your version of this file
27 * under either the MPL or the GPL.
28 */
29
30#ifndef _LINUX_TI113X_H
31#define _LINUX_TI113X_H
32
Linus Torvalds1da177e2005-04-16 15:20:36 -070033
34/* Register definitions for TI 113X PCI-to-CardBus bridges */
35
36/* System Control Register */
37#define TI113X_SYSTEM_CONTROL 0x0080 /* 32 bit */
38#define TI113X_SCR_SMIROUTE 0x04000000
39#define TI113X_SCR_SMISTATUS 0x02000000
40#define TI113X_SCR_SMIENB 0x01000000
41#define TI113X_SCR_VCCPROT 0x00200000
42#define TI113X_SCR_REDUCEZV 0x00100000
43#define TI113X_SCR_CDREQEN 0x00080000
44#define TI113X_SCR_CDMACHAN 0x00070000
45#define TI113X_SCR_SOCACTIVE 0x00002000
46#define TI113X_SCR_PWRSTREAM 0x00000800
47#define TI113X_SCR_DELAYUP 0x00000400
48#define TI113X_SCR_DELAYDOWN 0x00000200
49#define TI113X_SCR_INTERROGATE 0x00000100
50#define TI113X_SCR_CLKRUN_SEL 0x00000080
51#define TI113X_SCR_PWRSAVINGS 0x00000040
52#define TI113X_SCR_SUBSYSRW 0x00000020
53#define TI113X_SCR_CB_DPAR 0x00000010
54#define TI113X_SCR_CDMA_EN 0x00000008
55#define TI113X_SCR_ASYNC_IRQ 0x00000004
56#define TI113X_SCR_KEEPCLK 0x00000002
57#define TI113X_SCR_CLKRUN_ENA 0x00000001
58
59#define TI122X_SCR_SER_STEP 0xc0000000
60#define TI122X_SCR_INTRTIE 0x20000000
Daniel Ritz6c1a10d2005-09-20 14:12:17 -070061#define TIXX21_SCR_TIEALL 0x10000000
Linus Torvalds1da177e2005-04-16 15:20:36 -070062#define TI122X_SCR_CBRSVD 0x00400000
63#define TI122X_SCR_MRBURSTDN 0x00008000
64#define TI122X_SCR_MRBURSTUP 0x00004000
65#define TI122X_SCR_RIMUX 0x00000001
66
67/* Multimedia Control Register */
68#define TI1250_MULTIMEDIA_CTL 0x0084 /* 8 bit */
69#define TI1250_MMC_ZVOUTEN 0x80
70#define TI1250_MMC_PORTSEL 0x40
71#define TI1250_MMC_ZVEN1 0x02
72#define TI1250_MMC_ZVEN0 0x01
73
74#define TI1250_GENERAL_STATUS 0x0085 /* 8 bit */
75#define TI1250_GPIO0_CONTROL 0x0088 /* 8 bit */
76#define TI1250_GPIO1_CONTROL 0x0089 /* 8 bit */
77#define TI1250_GPIO2_CONTROL 0x008a /* 8 bit */
78#define TI1250_GPIO3_CONTROL 0x008b /* 8 bit */
79#define TI1250_GPIO_MODE_MASK 0xc0
80
81/* IRQMUX/MFUNC Register */
82#define TI122X_MFUNC 0x008c /* 32 bit */
83#define TI122X_MFUNC0_MASK 0x0000000f
84#define TI122X_MFUNC1_MASK 0x000000f0
85#define TI122X_MFUNC2_MASK 0x00000f00
86#define TI122X_MFUNC3_MASK 0x0000f000
87#define TI122X_MFUNC4_MASK 0x000f0000
88#define TI122X_MFUNC5_MASK 0x00f00000
89#define TI122X_MFUNC6_MASK 0x0f000000
90
91#define TI122X_MFUNC0_INTA 0x00000002
92#define TI125X_MFUNC0_INTB 0x00000001
93#define TI122X_MFUNC1_INTB 0x00000020
94#define TI122X_MFUNC3_IRQSER 0x00001000
95
96
97/* Retry Status Register */
98#define TI113X_RETRY_STATUS 0x0090 /* 8 bit */
99#define TI113X_RSR_PCIRETRY 0x80
100#define TI113X_RSR_CBRETRY 0x40
101#define TI113X_RSR_TEXP_CBB 0x20
102#define TI113X_RSR_MEXP_CBB 0x10
103#define TI113X_RSR_TEXP_CBA 0x08
104#define TI113X_RSR_MEXP_CBA 0x04
105#define TI113X_RSR_TEXP_PCI 0x02
106#define TI113X_RSR_MEXP_PCI 0x01
107
108/* Card Control Register */
109#define TI113X_CARD_CONTROL 0x0091 /* 8 bit */
110#define TI113X_CCR_RIENB 0x80
111#define TI113X_CCR_ZVENABLE 0x40
112#define TI113X_CCR_PCI_IRQ_ENA 0x20
113#define TI113X_CCR_PCI_IREQ 0x10
114#define TI113X_CCR_PCI_CSC 0x08
115#define TI113X_CCR_SPKROUTEN 0x02
116#define TI113X_CCR_IFG 0x01
117
118#define TI1220_CCR_PORT_SEL 0x20
119#define TI122X_CCR_AUD2MUX 0x04
120
121/* Device Control Register */
122#define TI113X_DEVICE_CONTROL 0x0092 /* 8 bit */
123#define TI113X_DCR_5V_FORCE 0x40
124#define TI113X_DCR_3V_FORCE 0x20
125#define TI113X_DCR_IMODE_MASK 0x06
126#define TI113X_DCR_IMODE_ISA 0x02
127#define TI113X_DCR_IMODE_SERIAL 0x04
128
129#define TI12XX_DCR_IMODE_PCI_ONLY 0x00
130#define TI12XX_DCR_IMODE_ALL_SERIAL 0x06
131
132/* Buffer Control Register */
133#define TI113X_BUFFER_CONTROL 0x0093 /* 8 bit */
134#define TI113X_BCR_CB_READ_DEPTH 0x08
135#define TI113X_BCR_CB_WRITE_DEPTH 0x04
136#define TI113X_BCR_PCI_READ_DEPTH 0x02
137#define TI113X_BCR_PCI_WRITE_DEPTH 0x01
138
139/* Diagnostic Register */
140#define TI1250_DIAGNOSTIC 0x0093 /* 8 bit */
141#define TI1250_DIAG_TRUE_VALUE 0x80
142#define TI1250_DIAG_PCI_IREQ 0x40
143#define TI1250_DIAG_PCI_CSC 0x20
144#define TI1250_DIAG_ASYNC_CSC 0x01
145
146/* DMA Registers */
147#define TI113X_DMA_0 0x0094 /* 32 bit */
148#define TI113X_DMA_1 0x0098 /* 32 bit */
149
150/* ExCA IO offset registers */
151#define TI113X_IO_OFFSET(map) (0x36+((map)<<1))
152
153/* EnE test register */
154#define ENE_TEST_C9 0xc9 /* 8bit */
155#define ENE_TEST_C9_TLTENABLE 0x02
Daniel Ritz8c3520d2005-08-21 22:29:26 -0700156#define ENE_TEST_C9_PFENABLE_F0 0x04
157#define ENE_TEST_C9_PFENABLE_F1 0x08
158#define ENE_TEST_C9_PFENABLE (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F0)
159#define ENE_TEST_C9_WPDISALBLE_F0 0x40
160#define ENE_TEST_C9_WPDISALBLE_F1 0x80
161#define ENE_TEST_C9_WPDISALBLE (ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700162
Linus Torvalds1da177e2005-04-16 15:20:36 -0700163/*
164 * Texas Instruments CardBus controller overrides.
165 */
166#define ti_sysctl(socket) ((socket)->private[0])
167#define ti_cardctl(socket) ((socket)->private[1])
168#define ti_devctl(socket) ((socket)->private[2])
169#define ti_diag(socket) ((socket)->private[3])
170#define ti_mfunc(socket) ((socket)->private[4])
171#define ene_test_c9(socket) ((socket)->private[5])
172
173/*
174 * These are the TI specific power management handlers.
175 */
176static void ti_save_state(struct yenta_socket *socket)
177{
178 ti_sysctl(socket) = config_readl(socket, TI113X_SYSTEM_CONTROL);
179 ti_mfunc(socket) = config_readl(socket, TI122X_MFUNC);
180 ti_cardctl(socket) = config_readb(socket, TI113X_CARD_CONTROL);
181 ti_devctl(socket) = config_readb(socket, TI113X_DEVICE_CONTROL);
182 ti_diag(socket) = config_readb(socket, TI1250_DIAGNOSTIC);
183
184 if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
185 ene_test_c9(socket) = config_readb(socket, ENE_TEST_C9);
186}
187
188static void ti_restore_state(struct yenta_socket *socket)
189{
190 config_writel(socket, TI113X_SYSTEM_CONTROL, ti_sysctl(socket));
191 config_writel(socket, TI122X_MFUNC, ti_mfunc(socket));
192 config_writeb(socket, TI113X_CARD_CONTROL, ti_cardctl(socket));
193 config_writeb(socket, TI113X_DEVICE_CONTROL, ti_devctl(socket));
194 config_writeb(socket, TI1250_DIAGNOSTIC, ti_diag(socket));
195
196 if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
197 config_writeb(socket, ENE_TEST_C9, ene_test_c9(socket));
198}
199
200/*
201 * Zoom video control for TI122x/113x chips
202 */
203
204static void ti_zoom_video(struct pcmcia_socket *sock, int onoff)
205{
206 u8 reg;
207 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
208
209 /* If we don't have a Zoom Video switch this is harmless,
210 we just tristate the unused (ZV) lines */
211 reg = config_readb(socket, TI113X_CARD_CONTROL);
212 if (onoff)
213 /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
214 reg |= TI113X_CCR_ZVENABLE;
215 else
216 reg &= ~TI113X_CCR_ZVENABLE;
217 config_writeb(socket, TI113X_CARD_CONTROL, reg);
218}
219
220/*
221 * The 145x series can also use this. They have an additional
222 * ZV autodetect mode we don't use but don't actually need.
223 * FIXME: manual says its in func0 and func1 but disagrees with
224 * itself about this - do we need to force func0, if so we need
225 * to know a lot more about socket pairings in pcmcia_socket than
226 * we do now.. uggh.
227 */
228
229static void ti1250_zoom_video(struct pcmcia_socket *sock, int onoff)
230{
231 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
232 int shift = 0;
233 u8 reg;
234
235 ti_zoom_video(sock, onoff);
236
237 reg = config_readb(socket, TI1250_MULTIMEDIA_CTL);
238 reg |= TI1250_MMC_ZVOUTEN; /* ZV bus enable */
239
240 if(PCI_FUNC(socket->dev->devfn)==1)
241 shift = 1;
242
243 if(onoff)
244 {
245 reg &= ~(1<<6); /* Clear select bit */
246 reg |= shift<<6; /* Favour our socket */
247 reg |= 1<<shift; /* Socket zoom video on */
248 }
249 else
250 {
251 reg &= ~(1<<6); /* Clear select bit */
252 reg |= (1^shift)<<6; /* Favour other socket */
253 reg &= ~(1<<shift); /* Socket zoon video off */
254 }
255
256 config_writeb(socket, TI1250_MULTIMEDIA_CTL, reg);
257}
258
259static void ti_set_zv(struct yenta_socket *socket)
260{
261 if(socket->dev->vendor == PCI_VENDOR_ID_TI)
262 {
263 switch(socket->dev->device)
264 {
265 /* There may be more .. */
266 case PCI_DEVICE_ID_TI_1220:
267 case PCI_DEVICE_ID_TI_1221:
268 case PCI_DEVICE_ID_TI_1225:
269 case PCI_DEVICE_ID_TI_4510:
270 socket->socket.zoom_video = ti_zoom_video;
271 break;
272 case PCI_DEVICE_ID_TI_1250:
273 case PCI_DEVICE_ID_TI_1251A:
274 case PCI_DEVICE_ID_TI_1251B:
275 case PCI_DEVICE_ID_TI_1450:
276 socket->socket.zoom_video = ti1250_zoom_video;
277 }
278 }
279}
280
281
282/*
283 * Generic TI init - TI has an extension for the
284 * INTCTL register that sets the PCI CSC interrupt.
285 * Make sure we set it correctly at open and init
286 * time
287 * - override: disable the PCI CSC interrupt. This makes
288 * it possible to use the CSC interrupt to probe the
289 * ISA interrupts.
290 * - init: set the interrupt to match our PCI state.
291 * This makes us correctly get PCI CSC interrupt
292 * events.
293 */
294static int ti_init(struct yenta_socket *socket)
295{
296 u8 new, reg = exca_readb(socket, I365_INTCTL);
297
298 new = reg & ~I365_INTR_ENA;
299 if (socket->cb_irq)
300 new |= I365_INTR_ENA;
301 if (new != reg)
302 exca_writeb(socket, I365_INTCTL, new);
303 return 0;
304}
305
306static int ti_override(struct yenta_socket *socket)
307{
308 u8 new, reg = exca_readb(socket, I365_INTCTL);
309
310 new = reg & ~I365_INTR_ENA;
311 if (new != reg)
312 exca_writeb(socket, I365_INTCTL, new);
313
314 ti_set_zv(socket);
315
316 return 0;
317}
318
319static int ti113x_override(struct yenta_socket *socket)
320{
321 u8 cardctl;
322
323 cardctl = config_readb(socket, TI113X_CARD_CONTROL);
324 cardctl &= ~(TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_IREQ | TI113X_CCR_PCI_CSC);
325 if (socket->cb_irq)
326 cardctl |= TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_CSC | TI113X_CCR_PCI_IREQ;
327 config_writeb(socket, TI113X_CARD_CONTROL, cardctl);
328
329 return ti_override(socket);
330}
331
332
333/* irqrouting for func0, probes PCI interrupt and ISA interrupts */
334static void ti12xx_irqroute_func0(struct yenta_socket *socket)
335{
336 u32 mfunc, mfunc_old, devctl;
337 u8 gpio3, gpio3_old;
338 int pci_irq_status;
339
340 mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
341 devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
342 printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
343 pci_name(socket->dev), mfunc, devctl);
344
345 /* make sure PCI interrupts are enabled before probing */
346 ti_init(socket);
347
348 /* test PCI interrupts first. only try fixing if return value is 0! */
349 pci_irq_status = yenta_probe_cb_irq(socket);
350 if (pci_irq_status)
351 goto out;
352
353 /*
354 * We're here which means PCI interrupts are _not_ delivered. try to
355 * find the right setting (all serial or parallel)
356 */
357 printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
358 pci_name(socket->dev));
359
360 /* for serial PCI make sure MFUNC3 is set to IRQSER */
361 if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
362 switch (socket->dev->device) {
363 case PCI_DEVICE_ID_TI_1250:
364 case PCI_DEVICE_ID_TI_1251A:
365 case PCI_DEVICE_ID_TI_1251B:
366 case PCI_DEVICE_ID_TI_1450:
367 case PCI_DEVICE_ID_TI_1451A:
368 case PCI_DEVICE_ID_TI_4450:
369 case PCI_DEVICE_ID_TI_4451:
370 /* these chips have no IRQSER setting in MFUNC3 */
371 break;
372
373 default:
374 mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
375
376 /* write down if changed, probe */
377 if (mfunc != mfunc_old) {
378 config_writel(socket, TI122X_MFUNC, mfunc);
379
380 pci_irq_status = yenta_probe_cb_irq(socket);
381 if (pci_irq_status == 1) {
382 printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts ok\n",
383 pci_name(socket->dev));
384 mfunc_old = mfunc;
385 goto out;
386 }
387
388 /* not working, back to old value */
389 mfunc = mfunc_old;
390 config_writel(socket, TI122X_MFUNC, mfunc);
391
392 if (pci_irq_status == -1)
393 goto out;
394 }
395 }
396
397 /* serial PCI interrupts not working fall back to parallel */
398 printk(KERN_INFO "Yenta TI: socket %s falling back to parallel PCI interrupts\n",
399 pci_name(socket->dev));
400 devctl &= ~TI113X_DCR_IMODE_MASK;
401 devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
402 config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
403 }
404
405 /* parallel PCI interrupts: route INTA */
406 switch (socket->dev->device) {
407 case PCI_DEVICE_ID_TI_1250:
408 case PCI_DEVICE_ID_TI_1251A:
409 case PCI_DEVICE_ID_TI_1251B:
410 case PCI_DEVICE_ID_TI_1450:
411 /* make sure GPIO3 is set to INTA */
412 gpio3 = gpio3_old = config_readb(socket, TI1250_GPIO3_CONTROL);
413 gpio3 &= ~TI1250_GPIO_MODE_MASK;
414 if (gpio3 != gpio3_old)
415 config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
416 break;
417
418 default:
419 gpio3 = gpio3_old = 0;
420
421 mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI122X_MFUNC0_INTA;
422 if (mfunc != mfunc_old)
423 config_writel(socket, TI122X_MFUNC, mfunc);
424 }
425
426 /* time to probe again */
427 pci_irq_status = yenta_probe_cb_irq(socket);
428 if (pci_irq_status == 1) {
429 mfunc_old = mfunc;
430 printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
431 pci_name(socket->dev));
432 } else {
433 /* not working, back to old value */
434 mfunc = mfunc_old;
435 config_writel(socket, TI122X_MFUNC, mfunc);
436 if (gpio3 != gpio3_old)
437 config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3_old);
438 }
439
440out:
441 if (pci_irq_status < 1) {
442 socket->cb_irq = 0;
443 printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
444 pci_name(socket->dev));
445 }
446}
447
448
Daniel Ritzc835a382005-05-05 16:15:57 -0700449/* changes the irq of func1 to match that of func0 */
450static int ti12xx_align_irqs(struct yenta_socket *socket, int *old_irq)
451{
452 struct pci_dev *func0;
453
454 /* find func0 device */
455 func0 = pci_get_slot(socket->dev->bus, socket->dev->devfn & ~0x07);
456 if (!func0)
457 return 0;
458
459 if (old_irq)
460 *old_irq = socket->cb_irq;
461 socket->cb_irq = socket->dev->irq = func0->irq;
462
463 pci_dev_put(func0);
464
465 return 1;
466}
467
Linus Torvalds1da177e2005-04-16 15:20:36 -0700468/*
469 * ties INTA and INTB together. also changes the devices irq to that of
470 * the function 0 device. call from func1 only.
471 * returns 1 if INTRTIE changed, 0 otherwise.
472 */
473static int ti12xx_tie_interrupts(struct yenta_socket *socket, int *old_irq)
474{
Linus Torvalds1da177e2005-04-16 15:20:36 -0700475 u32 sysctl;
Daniel Ritzc835a382005-05-05 16:15:57 -0700476 int ret;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700477
478 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
479 if (sysctl & TI122X_SCR_INTRTIE)
480 return 0;
481
Daniel Ritzc835a382005-05-05 16:15:57 -0700482 /* align */
483 ret = ti12xx_align_irqs(socket, old_irq);
484 if (!ret)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700485 return 0;
486
Daniel Ritzc835a382005-05-05 16:15:57 -0700487 /* tie */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700488 sysctl |= TI122X_SCR_INTRTIE;
489 config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
490
Linus Torvalds1da177e2005-04-16 15:20:36 -0700491 return 1;
492}
493
494/* undo what ti12xx_tie_interrupts() did */
495static void ti12xx_untie_interrupts(struct yenta_socket *socket, int old_irq)
496{
497 u32 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
498 sysctl &= ~TI122X_SCR_INTRTIE;
499 config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
500
501 socket->cb_irq = socket->dev->irq = old_irq;
502}
503
504/*
505 * irqrouting for func1, plays with INTB routing
506 * only touches MFUNC for INTB routing. all other bits are taken
507 * care of in func0 already.
508 */
509static void ti12xx_irqroute_func1(struct yenta_socket *socket)
510{
Daniel Ritzc835a382005-05-05 16:15:57 -0700511 u32 mfunc, mfunc_old, devctl, sysctl;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700512 int pci_irq_status;
513
514 mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
515 devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
516 printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
517 pci_name(socket->dev), mfunc, devctl);
518
Daniel Ritzc835a382005-05-05 16:15:57 -0700519 /* if IRQs are configured as tied, align irq of func1 with func0 */
520 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
521 if (sysctl & TI122X_SCR_INTRTIE)
522 ti12xx_align_irqs(socket, NULL);
523
Linus Torvalds1da177e2005-04-16 15:20:36 -0700524 /* make sure PCI interrupts are enabled before probing */
525 ti_init(socket);
526
527 /* test PCI interrupts first. only try fixing if return value is 0! */
528 pci_irq_status = yenta_probe_cb_irq(socket);
529 if (pci_irq_status)
530 goto out;
531
532 /*
533 * We're here which means PCI interrupts are _not_ delivered. try to
534 * find the right setting
535 */
536 printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
537 pci_name(socket->dev));
538
539
540 /* if all serial: set INTRTIE, probe again */
541 if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
542 int old_irq;
543
544 if (ti12xx_tie_interrupts(socket, &old_irq)) {
545 pci_irq_status = yenta_probe_cb_irq(socket);
546 if (pci_irq_status == 1) {
547 printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts, tied ok\n",
548 pci_name(socket->dev));
549 goto out;
550 }
551
552 ti12xx_untie_interrupts(socket, old_irq);
553 }
554 }
555 /* parallel PCI: route INTB, probe again */
556 else {
557 int old_irq;
558
559 switch (socket->dev->device) {
560 case PCI_DEVICE_ID_TI_1250:
561 /* the 1250 has one pin for IRQSER/INTB depending on devctl */
562 break;
563
564 case PCI_DEVICE_ID_TI_1251A:
565 case PCI_DEVICE_ID_TI_1251B:
566 case PCI_DEVICE_ID_TI_1450:
567 /*
568 * those have a pin for IRQSER/INTB plus INTB in MFUNC0
569 * we alread probed the shared pin, now go for MFUNC0
570 */
571 mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI125X_MFUNC0_INTB;
572 break;
573
574 default:
575 mfunc = (mfunc & ~TI122X_MFUNC1_MASK) | TI122X_MFUNC1_INTB;
576 break;
577 }
578
579 /* write, probe */
580 if (mfunc != mfunc_old) {
581 config_writel(socket, TI122X_MFUNC, mfunc);
582
583 pci_irq_status = yenta_probe_cb_irq(socket);
584 if (pci_irq_status == 1) {
585 printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
586 pci_name(socket->dev));
587 goto out;
588 }
589
590 mfunc = mfunc_old;
591 config_writel(socket, TI122X_MFUNC, mfunc);
592
593 if (pci_irq_status == -1)
594 goto out;
595 }
596
597 /* still nothing: set INTRTIE */
598 if (ti12xx_tie_interrupts(socket, &old_irq)) {
599 pci_irq_status = yenta_probe_cb_irq(socket);
600 if (pci_irq_status == 1) {
601 printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts, tied ok\n",
602 pci_name(socket->dev));
603 goto out;
604 }
605
606 ti12xx_untie_interrupts(socket, old_irq);
607 }
608 }
609
610out:
611 if (pci_irq_status < 1) {
612 socket->cb_irq = 0;
613 printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
614 pci_name(socket->dev));
615 }
616}
617
Daniel Ritzfa912bc2005-06-23 00:10:12 -0700618
619/* Returns true value if the second slot of a two-slot controller is empty */
620static int ti12xx_2nd_slot_empty(struct yenta_socket *socket)
621{
622 struct pci_dev *func;
623 struct yenta_socket *slot2;
624 int devfn;
625 unsigned int state;
626 int ret = 1;
Daniel Ritz6c1a10d2005-09-20 14:12:17 -0700627 u32 sysctl;
Daniel Ritzfa912bc2005-06-23 00:10:12 -0700628
629 /* catch the two-slot controllers */
630 switch (socket->dev->device) {
631 case PCI_DEVICE_ID_TI_1220:
632 case PCI_DEVICE_ID_TI_1221:
633 case PCI_DEVICE_ID_TI_1225:
634 case PCI_DEVICE_ID_TI_1251A:
635 case PCI_DEVICE_ID_TI_1251B:
636 case PCI_DEVICE_ID_TI_1420:
637 case PCI_DEVICE_ID_TI_1450:
638 case PCI_DEVICE_ID_TI_1451A:
639 case PCI_DEVICE_ID_TI_1520:
640 case PCI_DEVICE_ID_TI_1620:
641 case PCI_DEVICE_ID_TI_4520:
642 case PCI_DEVICE_ID_TI_4450:
643 case PCI_DEVICE_ID_TI_4451:
644 /*
645 * there are way more, but they need to be added in yenta_socket.c
646 * and pci_ids.h first anyway.
647 */
648 break;
649
Alex Williamson59e35ba2006-05-08 23:22:07 -0600650 case PCI_DEVICE_ID_TI_XX12:
Daniel Ritz6c1a10d2005-09-20 14:12:17 -0700651 case PCI_DEVICE_ID_TI_X515:
652 case PCI_DEVICE_ID_TI_X420:
653 case PCI_DEVICE_ID_TI_X620:
654 case PCI_DEVICE_ID_TI_XX21_XX11:
655 case PCI_DEVICE_ID_TI_7410:
656 case PCI_DEVICE_ID_TI_7610:
657 /*
658 * those are either single or dual slot CB with additional functions
659 * like 1394, smartcard reader, etc. check the TIEALL flag for them
660 * the TIEALL flag binds the IRQ of all functions toghether.
661 * we catch the single slot variants later.
662 */
663 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
664 if (sysctl & TIXX21_SCR_TIEALL)
665 return 0;
666
667 break;
668
Daniel Ritzfa912bc2005-06-23 00:10:12 -0700669 /* single-slot controllers have the 2nd slot empty always :) */
670 default:
671 return 1;
672 }
673
674 /* get other slot */
675 devfn = socket->dev->devfn & ~0x07;
676 func = pci_get_slot(socket->dev->bus,
677 (socket->dev->devfn & 0x07) ? devfn : devfn | 0x01);
678 if (!func)
679 return 1;
680
Daniel Ritz6c1a10d2005-09-20 14:12:17 -0700681 /*
682 * check that the device id of both slots match. this is needed for the
683 * XX21 and the XX11 controller that share the same device id for single
684 * and dual slot controllers. return '2nd slot empty'. we already checked
685 * if the interrupt is tied to another function.
686 */
687 if (socket->dev->device != func->device)
688 goto out;
689
Daniel Ritzfa912bc2005-06-23 00:10:12 -0700690 slot2 = pci_get_drvdata(func);
691 if (!slot2)
692 goto out;
693
694 /* check state */
695 yenta_get_status(&socket->socket, &state);
696 if (state & SS_DETECT) {
697 ret = 0;
698 goto out;
699 }
700
701out:
702 pci_dev_put(func);
703 return ret;
704}
705
706/*
707 * TI specifiy parts for the power hook.
708 *
709 * some TI's with some CB's produces interrupt storm on power on. it has been
710 * seen with atheros wlan cards on TI1225 and TI1410. solution is simply to
711 * disable any CB interrupts during this time.
712 */
713static int ti12xx_power_hook(struct pcmcia_socket *sock, int operation)
714{
715 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
716 u32 mfunc, devctl, sysctl;
717 u8 gpio3;
718
719 /* only POWER_PRE and POWER_POST are interesting */
720 if ((operation != HOOK_POWER_PRE) && (operation != HOOK_POWER_POST))
721 return 0;
722
723 devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
724 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
725 mfunc = config_readl(socket, TI122X_MFUNC);
726
727 /*
728 * all serial/tied: only disable when modparm set. always doing it
729 * would mean a regression for working setups 'cos it disables the
730 * interrupts for both both slots on 2-slot controllers
731 * (and users of single slot controllers where it's save have to
732 * live with setting the modparm, most don't have to anyway)
733 */
734 if (((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) &&
735 (pwr_irqs_off || ti12xx_2nd_slot_empty(socket))) {
736 switch (socket->dev->device) {
737 case PCI_DEVICE_ID_TI_1250:
738 case PCI_DEVICE_ID_TI_1251A:
739 case PCI_DEVICE_ID_TI_1251B:
740 case PCI_DEVICE_ID_TI_1450:
741 case PCI_DEVICE_ID_TI_1451A:
742 case PCI_DEVICE_ID_TI_4450:
743 case PCI_DEVICE_ID_TI_4451:
744 /* these chips have no IRQSER setting in MFUNC3 */
745 break;
746
747 default:
748 if (operation == HOOK_POWER_PRE)
749 mfunc = (mfunc & ~TI122X_MFUNC3_MASK);
750 else
751 mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
752 }
753
754 return 0;
755 }
756
757 /* do the job differently for func0/1 */
758 if ((PCI_FUNC(socket->dev->devfn) == 0) ||
759 ((sysctl & TI122X_SCR_INTRTIE) &&
760 (pwr_irqs_off || ti12xx_2nd_slot_empty(socket)))) {
761 /* some bridges are different */
762 switch (socket->dev->device) {
763 case PCI_DEVICE_ID_TI_1250:
764 case PCI_DEVICE_ID_TI_1251A:
765 case PCI_DEVICE_ID_TI_1251B:
766 case PCI_DEVICE_ID_TI_1450:
767 /* those oldies use gpio3 for INTA */
768 gpio3 = config_readb(socket, TI1250_GPIO3_CONTROL);
769 if (operation == HOOK_POWER_PRE)
770 gpio3 = (gpio3 & ~TI1250_GPIO_MODE_MASK) | 0x40;
771 else
772 gpio3 &= ~TI1250_GPIO_MODE_MASK;
773 config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
774 break;
775
776 default:
777 /* all new bridges are the same */
778 if (operation == HOOK_POWER_PRE)
779 mfunc &= ~TI122X_MFUNC0_MASK;
780 else
781 mfunc |= TI122X_MFUNC0_INTA;
782 config_writel(socket, TI122X_MFUNC, mfunc);
783 }
784 } else {
785 switch (socket->dev->device) {
786 case PCI_DEVICE_ID_TI_1251A:
787 case PCI_DEVICE_ID_TI_1251B:
788 case PCI_DEVICE_ID_TI_1450:
789 /* those have INTA elsewhere and INTB in MFUNC0 */
790 if (operation == HOOK_POWER_PRE)
791 mfunc &= ~TI122X_MFUNC0_MASK;
792 else
793 mfunc |= TI125X_MFUNC0_INTB;
794 config_writel(socket, TI122X_MFUNC, mfunc);
795
796 break;
797
798 default:
799 /* all new bridges are the same */
800 if (operation == HOOK_POWER_PRE)
801 mfunc &= ~TI122X_MFUNC1_MASK;
802 else
803 mfunc |= TI122X_MFUNC1_INTB;
804 config_writel(socket, TI122X_MFUNC, mfunc);
805 }
806 }
807
808 return 0;
809}
810
Linus Torvalds1da177e2005-04-16 15:20:36 -0700811static int ti12xx_override(struct yenta_socket *socket)
812{
813 u32 val, val_orig;
814
815 /* make sure that memory burst is active */
816 val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
817 if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
818 printk(KERN_INFO "Yenta: Disabling CLKRUN feature\n");
819 val |= TI113X_SCR_KEEPCLK;
820 }
821 if (!(val & TI122X_SCR_MRBURSTUP)) {
822 printk(KERN_INFO "Yenta: Enabling burst memory read transactions\n");
823 val |= TI122X_SCR_MRBURSTUP;
824 }
825 if (val_orig != val)
826 config_writel(socket, TI113X_SYSTEM_CONTROL, val);
827
828 /*
Linus Torvalds1da177e2005-04-16 15:20:36 -0700829 * Yenta expects controllers to use CSCINT to route
830 * CSC interrupts to PCI rather than INTVAL.
831 */
832 val = config_readb(socket, TI1250_DIAGNOSTIC);
833 printk(KERN_INFO "Yenta: Using %s to route CSC interrupts to PCI\n",
834 (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
835 printk(KERN_INFO "Yenta: Routing CardBus interrupts to %s\n",
836 (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
837
838 /* do irqrouting, depending on function */
839 if (PCI_FUNC(socket->dev->devfn) == 0)
840 ti12xx_irqroute_func0(socket);
841 else
842 ti12xx_irqroute_func1(socket);
843
Daniel Ritzfa912bc2005-06-23 00:10:12 -0700844 /* install power hook */
845 socket->socket.power_hook = ti12xx_power_hook;
846
Linus Torvalds1da177e2005-04-16 15:20:36 -0700847 return ti_override(socket);
848}
849
850
851static int ti1250_override(struct yenta_socket *socket)
852{
853 u8 old, diag;
854
855 old = config_readb(socket, TI1250_DIAGNOSTIC);
856 diag = old & ~(TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ);
857 if (socket->cb_irq)
858 diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
859
860 if (diag != old) {
861 printk(KERN_INFO "Yenta: adjusting diagnostic: %02x -> %02x\n",
862 old, diag);
863 config_writeb(socket, TI1250_DIAGNOSTIC, diag);
864 }
865
866 return ti12xx_override(socket);
867}
868
Daniel Ritz8c3520d2005-08-21 22:29:26 -0700869
870/**
871 * EnE specific part. EnE bridges are register compatible with TI bridges but
872 * have their own test registers and more important their own little problems.
873 * Some fixup code to make everybody happy (TM).
874 */
875
Daniel Ritz63e7ebd2005-11-03 21:12:14 +0100876#ifdef CONFIG_YENTA_ENE_TUNE
Daniel Ritz8c3520d2005-08-21 22:29:26 -0700877/**
878 * set/clear various test bits:
879 * Defaults to clear the bit.
880 * - mask (u8) defines what bits to change
881 * - bits (u8) is the values to change them to
882 * -> it's
883 * current = (current & ~mask) | bits
884 */
885/* pci ids of devices that wants to have the bit set */
886#define DEVID(_vend,_dev,_subvend,_subdev,mask,bits) { \
887 .vendor = _vend, \
888 .device = _dev, \
889 .subvendor = _subvend, \
890 .subdevice = _subdev, \
891 .driver_data = ((mask) << 8 | (bits)), \
892 }
893static struct pci_device_id ene_tune_tbl[] = {
894 /* Echo Audio products based on motorola DSP56301 and DSP56361 */
895 DEVID(PCI_VENDOR_ID_MOTOROLA, 0x1801, 0xECC0, PCI_ANY_ID,
896 ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
897 DEVID(PCI_VENDOR_ID_MOTOROLA, 0x3410, 0xECC0, PCI_ANY_ID,
898 ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
899
900 {}
901};
902
903static void ene_tune_bridge(struct pcmcia_socket *sock, struct pci_bus *bus)
904{
905 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
906 struct pci_dev *dev;
907 struct pci_device_id *id = NULL;
908 u8 test_c9, old_c9, mask, bits;
909
910 list_for_each_entry(dev, &bus->devices, bus_list) {
911 id = (struct pci_device_id *) pci_match_id(ene_tune_tbl, dev);
912 if (id)
913 break;
914 }
915
916 test_c9 = old_c9 = config_readb(socket, ENE_TEST_C9);
917 if (id) {
918 mask = (id->driver_data >> 8) & 0xFF;
919 bits = id->driver_data & 0xFF;
920
921 test_c9 = (test_c9 & ~mask) | bits;
922 }
923 else
924 /* default to clear TLTEnable bit, old behaviour */
925 test_c9 &= ~ENE_TEST_C9_TLTENABLE;
926
927 printk(KERN_INFO "yenta EnE: chaning testregister 0xC9, %02x -> %02x\n", old_c9, test_c9);
928 config_writeb(socket, ENE_TEST_C9, test_c9);
929}
930
Daniel Ritz8c3520d2005-08-21 22:29:26 -0700931static int ene_override(struct yenta_socket *socket)
932{
933 /* install tune_bridge() function */
934 socket->socket.tune_bridge = ene_tune_bridge;
935
936 return ti1250_override(socket);
937}
David Vrabelc2059b22005-10-07 14:43:22 +0100938#else
939# define ene_override ti1250_override
Daniel Ritz63e7ebd2005-11-03 21:12:14 +0100940#endif /* !CONFIG_YENTA_ENE_TUNE */
Daniel Ritz8c3520d2005-08-21 22:29:26 -0700941
Linus Torvalds1da177e2005-04-16 15:20:36 -0700942#endif /* _LINUX_TI113X_H */
943