Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 1 | /* |
| 2 | * hfcsusb.h, HFC-S USB mISDN driver |
| 3 | */ |
| 4 | |
| 5 | #ifndef __HFCSUSB_H__ |
| 6 | #define __HFCSUSB_H__ |
| 7 | |
| 8 | |
| 9 | #define DRIVER_NAME "HFC-S_USB" |
| 10 | |
| 11 | #define DBG_HFC_CALL_TRACE 0x00010000 |
| 12 | #define DBG_HFC_FIFO_VERBOSE 0x00020000 |
| 13 | #define DBG_HFC_USB_VERBOSE 0x00100000 |
| 14 | #define DBG_HFC_URB_INFO 0x00200000 |
| 15 | #define DBG_HFC_URB_ERROR 0x00400000 |
| 16 | |
| 17 | #define DEFAULT_TRANSP_BURST_SZ 128 |
| 18 | |
| 19 | #define HFC_CTRL_TIMEOUT 20 /* 5ms timeout writing/reading regs */ |
| 20 | #define CLKDEL_TE 0x0f /* CLKDEL in TE mode */ |
| 21 | #define CLKDEL_NT 0x6c /* CLKDEL in NT mode */ |
| 22 | |
| 23 | /* hfcsusb Layer1 commands */ |
| 24 | #define HFC_L1_ACTIVATE_TE 1 |
| 25 | #define HFC_L1_ACTIVATE_NT 2 |
| 26 | #define HFC_L1_DEACTIVATE_NT 3 |
| 27 | #define HFC_L1_FORCE_DEACTIVATE_TE 4 |
| 28 | |
| 29 | /* cmd FLAGS in HFCUSB_STATES register */ |
| 30 | #define HFCUSB_LOAD_STATE 0x10 |
| 31 | #define HFCUSB_ACTIVATE 0x20 |
| 32 | #define HFCUSB_DO_ACTION 0x40 |
| 33 | #define HFCUSB_NT_G2_G3 0x80 |
| 34 | |
| 35 | /* timers */ |
| 36 | #define NT_ACTIVATION_TIMER 0x01 /* enables NT mode activation Timer */ |
| 37 | #define NT_T1_COUNT 10 |
| 38 | |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 39 | #define MAX_BCH_SIZE 2048 /* allowed B-channel packet size */ |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 40 | |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 41 | #define HFCUSB_RX_THRESHOLD 64 /* threshold for fifo report bit rx */ |
| 42 | #define HFCUSB_TX_THRESHOLD 96 /* threshold for fifo report bit tx */ |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 43 | |
| 44 | #define HFCUSB_CHIP_ID 0x16 /* Chip ID register index */ |
| 45 | #define HFCUSB_CIRM 0x00 /* cirm register index */ |
| 46 | #define HFCUSB_USB_SIZE 0x07 /* int length register */ |
| 47 | #define HFCUSB_USB_SIZE_I 0x06 /* iso length register */ |
| 48 | #define HFCUSB_F_CROSS 0x0b /* bit order register */ |
| 49 | #define HFCUSB_CLKDEL 0x37 /* bit delay register */ |
| 50 | #define HFCUSB_CON_HDLC 0xfa /* channel connect register */ |
| 51 | #define HFCUSB_HDLC_PAR 0xfb |
| 52 | #define HFCUSB_SCTRL 0x31 /* S-bus control register (tx) */ |
| 53 | #define HFCUSB_SCTRL_E 0x32 /* same for E and special funcs */ |
| 54 | #define HFCUSB_SCTRL_R 0x33 /* S-bus control register (rx) */ |
| 55 | #define HFCUSB_F_THRES 0x0c /* threshold register */ |
| 56 | #define HFCUSB_FIFO 0x0f /* fifo select register */ |
| 57 | #define HFCUSB_F_USAGE 0x1a /* fifo usage register */ |
| 58 | #define HFCUSB_MST_MODE0 0x14 |
| 59 | #define HFCUSB_MST_MODE1 0x15 |
| 60 | #define HFCUSB_P_DATA 0x1f |
| 61 | #define HFCUSB_INC_RES_F 0x0e |
| 62 | #define HFCUSB_B1_SSL 0x20 |
| 63 | #define HFCUSB_B2_SSL 0x21 |
| 64 | #define HFCUSB_B1_RSL 0x24 |
| 65 | #define HFCUSB_B2_RSL 0x25 |
| 66 | #define HFCUSB_STATES 0x30 |
| 67 | |
| 68 | |
| 69 | #define HFCUSB_CHIPID 0x40 /* ID value of HFC-S USB */ |
| 70 | |
| 71 | /* fifo registers */ |
| 72 | #define HFCUSB_NUM_FIFOS 8 /* maximum number of fifos */ |
| 73 | #define HFCUSB_B1_TX 0 /* index for B1 transmit bulk/int */ |
| 74 | #define HFCUSB_B1_RX 1 /* index for B1 receive bulk/int */ |
| 75 | #define HFCUSB_B2_TX 2 |
| 76 | #define HFCUSB_B2_RX 3 |
| 77 | #define HFCUSB_D_TX 4 |
| 78 | #define HFCUSB_D_RX 5 |
| 79 | #define HFCUSB_PCM_TX 6 |
| 80 | #define HFCUSB_PCM_RX 7 |
| 81 | |
| 82 | |
| 83 | #define USB_INT 0 |
| 84 | #define USB_BULK 1 |
| 85 | #define USB_ISOC 2 |
| 86 | |
| 87 | #define ISOC_PACKETS_D 8 |
| 88 | #define ISOC_PACKETS_B 8 |
| 89 | #define ISO_BUFFER_SIZE 128 |
| 90 | |
| 91 | /* defines how much ISO packets are handled in one URB */ |
| 92 | static int iso_packets[8] = |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 93 | { ISOC_PACKETS_B, ISOC_PACKETS_B, ISOC_PACKETS_B, ISOC_PACKETS_B, |
| 94 | ISOC_PACKETS_D, ISOC_PACKETS_D, ISOC_PACKETS_D, ISOC_PACKETS_D |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 95 | }; |
| 96 | |
| 97 | |
| 98 | /* Fifo flow Control for TX ISO */ |
| 99 | #define SINK_MAX 68 |
| 100 | #define SINK_MIN 48 |
| 101 | #define SINK_DMIN 12 |
| 102 | #define SINK_DMAX 18 |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 103 | #define BITLINE_INF (-96 * 8) |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 104 | |
| 105 | /* HFC-S USB register access by Control-URSs */ |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 106 | #define write_reg_atomic(a, b, c) \ |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 107 | usb_control_msg((a)->dev, (a)->ctrl_out_pipe, 0, 0x40, (c), (b), \ |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 108 | 0, 0, HFC_CTRL_TIMEOUT) |
| 109 | #define read_reg_atomic(a, b, c) \ |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 110 | usb_control_msg((a)->dev, (a)->ctrl_in_pipe, 1, 0xC0, 0, (b), (c), \ |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 111 | 1, HFC_CTRL_TIMEOUT) |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 112 | #define HFC_CTRL_BUFSIZE 64 |
| 113 | |
| 114 | struct ctrl_buf { |
| 115 | __u8 hfcs_reg; /* register number */ |
| 116 | __u8 reg_val; /* value to be written (or read) */ |
| 117 | }; |
| 118 | |
| 119 | /* |
| 120 | * URB error codes |
| 121 | * Used to represent a list of values and their respective symbolic names |
| 122 | */ |
| 123 | struct hfcusb_symbolic_list { |
| 124 | const int num; |
| 125 | const char *name; |
| 126 | }; |
| 127 | |
| 128 | static struct hfcusb_symbolic_list urb_errlist[] = { |
| 129 | {-ENOMEM, "No memory for allocation of internal structures"}, |
| 130 | {-ENOSPC, "The host controller's bandwidth is already consumed"}, |
| 131 | {-ENOENT, "URB was canceled by unlink_urb"}, |
| 132 | {-EXDEV, "ISO transfer only partially completed"}, |
| 133 | {-EAGAIN, "Too match scheduled for the future"}, |
| 134 | {-ENXIO, "URB already queued"}, |
| 135 | {-EFBIG, "Too much ISO frames requested"}, |
| 136 | {-ENOSR, "Buffer error (overrun)"}, |
| 137 | {-EPIPE, "Specified endpoint is stalled (device not responding)"}, |
| 138 | {-EOVERFLOW, "Babble (bad cable?)"}, |
| 139 | {-EPROTO, "Bit-stuff error (bad cable?)"}, |
| 140 | {-EILSEQ, "CRC/Timeout"}, |
| 141 | {-ETIMEDOUT, "NAK (device does not respond)"}, |
| 142 | {-ESHUTDOWN, "Device unplugged"}, |
| 143 | {-1, NULL} |
| 144 | }; |
| 145 | |
| 146 | static inline const char * |
| 147 | symbolic(struct hfcusb_symbolic_list list[], const int num) |
| 148 | { |
| 149 | int i; |
| 150 | for (i = 0; list[i].name != NULL; i++) |
| 151 | if (list[i].num == num) |
| 152 | return list[i].name; |
André Goddard Rosa | af901ca | 2009-11-14 13:09:05 -0200 | [diff] [blame] | 153 | return "<unknown USB Error>"; |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 154 | } |
| 155 | |
| 156 | /* USB descriptor need to contain one of the following EndPoint combination: */ |
| 157 | #define CNF_4INT3ISO 1 /* 4 INT IN, 3 ISO OUT */ |
| 158 | #define CNF_3INT3ISO 2 /* 3 INT IN, 3 ISO OUT */ |
| 159 | #define CNF_4ISO3ISO 3 /* 4 ISO IN, 3 ISO OUT */ |
| 160 | #define CNF_3ISO3ISO 4 /* 3 ISO IN, 3 ISO OUT */ |
| 161 | |
| 162 | #define EP_NUL 1 /* Endpoint at this position not allowed */ |
| 163 | #define EP_NOP 2 /* all type of endpoints allowed at this position */ |
| 164 | #define EP_ISO 3 /* Isochron endpoint mandatory at this position */ |
| 165 | #define EP_BLK 4 /* Bulk endpoint mandatory at this position */ |
| 166 | #define EP_INT 5 /* Interrupt endpoint mandatory at this position */ |
| 167 | |
| 168 | #define HFC_CHAN_B1 0 |
| 169 | #define HFC_CHAN_B2 1 |
| 170 | #define HFC_CHAN_D 2 |
| 171 | #define HFC_CHAN_E 3 |
| 172 | |
| 173 | |
| 174 | /* |
| 175 | * List of all supported enpoints configiration sets, used to find the |
| 176 | * best matching endpoint configuration within a devices' USB descriptor. |
| 177 | * We need at least 3 RX endpoints, and 3 TX endpoints, either |
| 178 | * INT-in and ISO-out, or ISO-in and ISO-out) |
| 179 | * with 4 RX endpoints even E-Channel logging is possible |
| 180 | */ |
| 181 | static int |
| 182 | validconf[][19] = { |
| 183 | /* INT in, ISO out config */ |
| 184 | {EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NOP, EP_INT, |
| 185 | EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_NUL, EP_NUL, |
| 186 | CNF_4INT3ISO, 2, 1}, |
| 187 | {EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_NUL, |
| 188 | EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_NUL, EP_NUL, |
| 189 | CNF_3INT3ISO, 2, 0}, |
| 190 | /* ISO in, ISO out config */ |
| 191 | {EP_NOP, EP_NOP, EP_NOP, EP_NOP, EP_NOP, EP_NOP, EP_NOP, EP_NOP, |
| 192 | EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_NOP, EP_ISO, |
| 193 | CNF_4ISO3ISO, 2, 1}, |
| 194 | {EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, |
| 195 | EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_NUL, EP_NUL, |
| 196 | CNF_3ISO3ISO, 2, 0}, |
| 197 | {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} /* EOL element */ |
| 198 | }; |
| 199 | |
| 200 | /* string description of chosen config */ |
Hannes Eder | 6c2959a | 2009-02-12 09:28:40 +0000 | [diff] [blame] | 201 | static char *conf_str[] = { |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 202 | "4 Interrupt IN + 3 Isochron OUT", |
| 203 | "3 Interrupt IN + 3 Isochron OUT", |
| 204 | "4 Isochron IN + 3 Isochron OUT", |
| 205 | "3 Isochron IN + 3 Isochron OUT" |
| 206 | }; |
| 207 | |
| 208 | |
| 209 | #define LED_OFF 0 /* no LED support */ |
| 210 | #define LED_SCHEME1 1 /* LED standard scheme */ |
| 211 | #define LED_SCHEME2 2 /* not used yet... */ |
| 212 | |
| 213 | #define LED_POWER_ON 1 |
| 214 | #define LED_POWER_OFF 2 |
| 215 | #define LED_S0_ON 3 |
| 216 | #define LED_S0_OFF 4 |
| 217 | #define LED_B1_ON 5 |
| 218 | #define LED_B1_OFF 6 |
| 219 | #define LED_B1_DATA 7 |
| 220 | #define LED_B2_ON 8 |
| 221 | #define LED_B2_OFF 9 |
| 222 | #define LED_B2_DATA 10 |
| 223 | |
| 224 | #define LED_NORMAL 0 /* LEDs are normal */ |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 225 | #define LED_INVERTED 1 /* LEDs are inverted */ |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 226 | |
| 227 | /* time in ms to perform a Flashing LED when B-Channel has traffic */ |
| 228 | #define LED_TIME 250 |
| 229 | |
| 230 | |
| 231 | |
| 232 | struct hfcsusb; |
| 233 | struct usb_fifo; |
| 234 | |
| 235 | /* structure defining input+output fifos (interrupt/bulk mode) */ |
| 236 | struct iso_urb { |
| 237 | struct urb *urb; |
| 238 | __u8 buffer[ISO_BUFFER_SIZE]; /* buffer rx/tx USB URB data */ |
| 239 | struct usb_fifo *owner_fifo; /* pointer to owner fifo */ |
| 240 | __u8 indx; /* Fifos's ISO double buffer 0 or 1 ? */ |
| 241 | #ifdef ISO_FRAME_START_DEBUG |
| 242 | int start_frames[ISO_FRAME_START_RING_COUNT]; |
| 243 | __u8 iso_frm_strt_pos; /* index in start_frame[] */ |
| 244 | #endif |
| 245 | }; |
| 246 | |
| 247 | struct usb_fifo { |
| 248 | int fifonum; /* fifo index attached to this structure */ |
| 249 | int active; /* fifo is currently active */ |
| 250 | struct hfcsusb *hw; /* pointer to main structure */ |
| 251 | int pipe; /* address of endpoint */ |
| 252 | __u8 usb_packet_maxlen; /* maximum length for usb transfer */ |
| 253 | unsigned int max_size; /* maximum size of receive/send packet */ |
| 254 | __u8 intervall; /* interrupt interval */ |
| 255 | struct urb *urb; /* transfer structure for usb routines */ |
| 256 | __u8 buffer[128]; /* buffer USB INT OUT URB data */ |
| 257 | int bit_line; /* how much bits are in the fifo? */ |
| 258 | |
| 259 | __u8 usb_transfer_mode; /* switched between ISO and INT */ |
| 260 | struct iso_urb iso[2]; /* two urbs to have one always |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 261 | one pending */ |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 262 | |
| 263 | struct dchannel *dch; /* link to hfcsusb_t->dch */ |
| 264 | struct bchannel *bch; /* link to hfcsusb_t->bch */ |
| 265 | struct dchannel *ech; /* link to hfcsusb_t->ech, TODO: E-CHANNEL */ |
| 266 | int last_urblen; /* remember length of last packet */ |
| 267 | __u8 stop_gracefull; /* stops URB retransmission */ |
| 268 | }; |
| 269 | |
| 270 | struct hfcsusb { |
| 271 | struct list_head list; |
| 272 | struct dchannel dch; |
| 273 | struct bchannel bch[2]; |
| 274 | struct dchannel ech; /* TODO : wait for struct echannel ;) */ |
| 275 | |
| 276 | struct usb_device *dev; /* our device */ |
| 277 | struct usb_interface *intf; /* used interface */ |
| 278 | int if_used; /* used interface number */ |
| 279 | int alt_used; /* used alternate config */ |
| 280 | int cfg_used; /* configuration index used */ |
| 281 | int vend_idx; /* index in hfcsusb_idtab */ |
| 282 | int packet_size; |
| 283 | int iso_packet_size; |
| 284 | struct usb_fifo fifos[HFCUSB_NUM_FIFOS]; |
| 285 | |
| 286 | /* control pipe background handling */ |
| 287 | struct ctrl_buf ctrl_buff[HFC_CTRL_BUFSIZE]; |
| 288 | int ctrl_in_idx, ctrl_out_idx, ctrl_cnt; |
| 289 | struct urb *ctrl_urb; |
| 290 | struct usb_ctrlrequest ctrl_write; |
| 291 | struct usb_ctrlrequest ctrl_read; |
| 292 | int ctrl_paksize; |
| 293 | int ctrl_in_pipe, ctrl_out_pipe; |
| 294 | spinlock_t ctrl_lock; /* lock for ctrl */ |
| 295 | spinlock_t lock; |
| 296 | |
| 297 | __u8 threshold_mask; |
| 298 | __u8 led_state; |
| 299 | |
| 300 | __u8 protocol; |
| 301 | int nt_timer; |
| 302 | int open; |
| 303 | __u8 timers; |
| 304 | __u8 initdone; |
| 305 | char name[MISDN_MAX_IDLEN]; |
| 306 | }; |
| 307 | |
| 308 | /* private vendor specific data */ |
| 309 | struct hfcsusb_vdata { |
| 310 | __u8 led_scheme; /* led display scheme */ |
| 311 | signed short led_bits[8]; /* array of 8 possible LED bitmask */ |
| 312 | char *vend_name; /* device name */ |
| 313 | }; |
| 314 | |
| 315 | |
| 316 | #define HFC_MAX_TE_LAYER1_STATE 8 |
| 317 | #define HFC_MAX_NT_LAYER1_STATE 4 |
| 318 | |
Hannes Eder | 6c2959a | 2009-02-12 09:28:40 +0000 | [diff] [blame] | 319 | static const char *HFC_TE_LAYER1_STATES[HFC_MAX_TE_LAYER1_STATE + 1] = { |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 320 | "TE F0 - Reset", |
| 321 | "TE F1 - Reset", |
| 322 | "TE F2 - Sensing", |
| 323 | "TE F3 - Deactivated", |
| 324 | "TE F4 - Awaiting signal", |
| 325 | "TE F5 - Identifying input", |
| 326 | "TE F6 - Synchronized", |
| 327 | "TE F7 - Activated", |
| 328 | "TE F8 - Lost framing", |
| 329 | }; |
| 330 | |
Hannes Eder | 6c2959a | 2009-02-12 09:28:40 +0000 | [diff] [blame] | 331 | static const char *HFC_NT_LAYER1_STATES[HFC_MAX_NT_LAYER1_STATE + 1] = { |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 332 | "NT G0 - Reset", |
| 333 | "NT G1 - Deactive", |
| 334 | "NT G2 - Pending activation", |
| 335 | "NT G3 - Active", |
| 336 | "NT G4 - Pending deactivation", |
| 337 | }; |
| 338 | |
| 339 | /* supported devices */ |
| 340 | static struct usb_device_id hfcsusb_idtab[] = { |
| 341 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 342 | USB_DEVICE(0x0959, 0x2bd0), |
| 343 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 344 | {LED_OFF, {4, 0, 2, 1}, |
| 345 | "ISDN USB TA (Cologne Chip HFC-S USB based)"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 346 | }, |
| 347 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 348 | USB_DEVICE(0x0675, 0x1688), |
| 349 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 350 | {LED_SCHEME1, {1, 2, 0, 0}, |
| 351 | "DrayTek miniVigor 128 USB ISDN TA"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 352 | }, |
| 353 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 354 | USB_DEVICE(0x07b0, 0x0007), |
| 355 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 356 | {LED_SCHEME1, {0x80, -64, -32, -16}, |
| 357 | "Billion tiny USB ISDN TA 128"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 358 | }, |
| 359 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 360 | USB_DEVICE(0x0742, 0x2008), |
| 361 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 362 | {LED_SCHEME1, {4, 0, 2, 1}, |
| 363 | "Stollmann USB TA"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 364 | }, |
| 365 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 366 | USB_DEVICE(0x0742, 0x2009), |
| 367 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 368 | {LED_SCHEME1, {4, 0, 2, 1}, |
| 369 | "Aceex USB ISDN TA"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 370 | }, |
| 371 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 372 | USB_DEVICE(0x0742, 0x200A), |
| 373 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 374 | {LED_SCHEME1, {4, 0, 2, 1}, |
| 375 | "OEM USB ISDN TA"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 376 | }, |
| 377 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 378 | USB_DEVICE(0x08e3, 0x0301), |
| 379 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 380 | {LED_SCHEME1, {2, 0, 1, 4}, |
| 381 | "Olitec USB RNIS"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 382 | }, |
| 383 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 384 | USB_DEVICE(0x07fa, 0x0846), |
| 385 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 386 | {LED_SCHEME1, {0x80, -64, -32, -16}, |
| 387 | "Bewan Modem RNIS USB"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 388 | }, |
| 389 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 390 | USB_DEVICE(0x07fa, 0x0847), |
| 391 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 392 | {LED_SCHEME1, {0x80, -64, -32, -16}, |
| 393 | "Djinn Numeris USB"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 394 | }, |
| 395 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 396 | USB_DEVICE(0x07b0, 0x0006), |
| 397 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 398 | {LED_SCHEME1, {0x80, -64, -32, -16}, |
| 399 | "Twister ISDN TA"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 400 | }, |
| 401 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 402 | USB_DEVICE(0x071d, 0x1005), |
| 403 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 404 | {LED_SCHEME1, {0x02, 0, 0x01, 0x04}, |
| 405 | "Eicon DIVA USB 4.0"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 406 | }, |
| 407 | { |
Joe Perches | 475be4d | 2012-02-19 19:52:38 -0800 | [diff] [blame] | 408 | USB_DEVICE(0x0586, 0x0102), |
| 409 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 410 | {LED_SCHEME1, {0x88, -64, -32, -16}, |
| 411 | "ZyXEL OMNI.NET USB II"}), |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 412 | }, |
Karsten Keil | 2cfb311 | 2012-05-21 21:14:14 +0000 | [diff] [blame] | 413 | { |
| 414 | USB_DEVICE(0x1ae7, 0x0525), |
| 415 | .driver_info = (unsigned long) &((struct hfcsusb_vdata) |
| 416 | {LED_SCHEME1, {0x88, -64, -32, -16}, |
| 417 | "X-Tensions USB ISDN TA XC-525"}), |
| 418 | }, |
Karsten Keil | 69f52ad | 2009-01-09 16:20:51 +0100 | [diff] [blame] | 419 | { } |
| 420 | }; |
| 421 | |
| 422 | MODULE_DEVICE_TABLE(usb, hfcsusb_idtab); |
| 423 | |
| 424 | #endif /* __HFCSUSB_H__ */ |