blob: cde0ed097af689d626aac2d699069f7c71b5783b [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# Video configuration
3#
4
5menu "Graphics support"
6
7config FB
8 tristate "Support for frame buffer devices"
9 ---help---
10 The frame buffer device provides an abstraction for the graphics
11 hardware. It represents the frame buffer of some video hardware and
12 allows application software to access the graphics hardware through
13 a well-defined interface, so the software doesn't need to know
14 anything about the low-level (hardware register) stuff.
15
16 Frame buffer devices work identically across the different
17 architectures supported by Linux and make the implementation of
18 application programs easier and more portable; at this point, an X
19 server exists which uses the frame buffer device exclusively.
20 On several non-X86 architectures, the frame buffer device is the
21 only way to use the graphics hardware.
22
23 The device is accessed through special device nodes, usually located
24 in the /dev directory, i.e. /dev/fb*.
25
26 You need an utility program called fbset to make full use of frame
27 buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
28 and the Framebuffer-HOWTO at
29 <http://www.tahallah.demon.co.uk/programming/prog.html> for more
30 information.
31
32 Say Y here and to the driver for your graphics board below if you
33 are compiling a kernel for a non-x86 architecture.
34
35 If you are compiling for the x86 architecture, you can say Y if you
36 want to play with it, but it is not essential. Please note that
37 running graphical applications that directly touch the hardware
38 (e.g. an accelerated X server) and that are not frame buffer
39 device-aware may cause unexpected results. If unsure, say N.
40
41config FB_CFB_FILLRECT
42 tristate
43 depends on FB
44 default n
45 ---help---
46 Include the cfb_fillrect function for generic software rectangle
47 filling. This is used by drivers that don't provide their own
48 (accelerated) version.
49
50config FB_CFB_COPYAREA
51 tristate
52 depends on FB
53 default n
54 ---help---
55 Include the cfb_copyarea function for generic software area copying.
56 This is used by drivers that don't provide their own (accelerated)
57 version.
58
59config FB_CFB_IMAGEBLIT
60 tristate
61 depends on FB
62 default n
63 ---help---
64 Include the cfb_imageblit function for generic software image
65 blitting. This is used by drivers that don't provide their own
66 (accelerated) version.
67
68config FB_SOFT_CURSOR
69 tristate
70 depends on FB
71 default n
72 ---help---
73 Include the soft_cursor function for generic software cursor support.
74 This is used by drivers that don't provide their own (accelerated)
75 version.
76
77config FB_MACMODES
78 tristate
79 depends on FB
80 default n
81
82config FB_MODE_HELPERS
83 bool "Enable Video Mode Handling Helpers"
84 depends on FB
85 default n
86 ---help---
87 This enables functions for handling video modes using the
88 Generalized Timing Formula and the EDID parser. A few drivers rely
89 on this feature such as the radeonfb, rivafb, and the i810fb. If
90 your driver does not take advantage of this feature, choosing Y will
91 just increase the kernel size by about 5K.
92
93config FB_TILEBLITTING
94 bool "Enable Tile Blitting Support"
95 depends on FB
96 default n
97 ---help---
98 This enables tile blitting. Tile blitting is a drawing technique
99 where the screen is divided into rectangular sections (tiles), whereas
100 the standard blitting divides the screen into pixels. Because the
101 default drawing element is a tile, drawing functions will be passed
102 parameters in terms of number of tiles instead of number of pixels.
103 For example, to draw a single character, instead of using bitmaps,
104 an index to an array of bitmaps will be used. To clear or move a
105 rectangular section of a screen, the rectangle will be described in
106 terms of number of tiles in the x- and y-axis.
107
108 This is particularly important to one driver, matroxfb. If
109 unsure, say N.
110
111config FB_CIRRUS
112 tristate "Cirrus Logic support"
113 depends on FB && (ZORRO || PCI)
114 select FB_CFB_FILLRECT
115 select FB_CFB_COPYAREA
116 select FB_CFB_IMAGEBLIT
117 select FB_SOFT_CURSOR
118 ---help---
119 This enables support for Cirrus Logic GD542x/543x based boards on
120 Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
121
122 If you have a PCI-based system, this enables support for these
123 chips: GD-543x, GD-544x, GD-5480.
124
125 Please read the file <file:Documentation/fb/cirrusfb.txt>.
126
127 Say N unless you have such a graphics board or plan to get one
128 before you next recompile the kernel.
129
130config FB_PM2
131 tristate "Permedia2 support"
132 depends on FB && ((AMIGA && BROKEN) || PCI)
133 select FB_CFB_FILLRECT
134 select FB_CFB_COPYAREA
135 select FB_CFB_IMAGEBLIT
136 select FB_SOFT_CURSOR
137 help
138 This is the frame buffer device driver for the Permedia2 AGP frame
139 buffer card from ASK, aka `Graphic Blaster Exxtreme'. There is a
140 product page at
141 <http://www.ask.com.hk/product/Permedia%202/permedia2.htm>.
142
143config FB_PM2_FIFO_DISCONNECT
144 bool "enable FIFO disconnect feature"
145 depends on FB_PM2 && PCI
146 help
147 Support the Permedia2 FIFO disconnect feature (see CONFIG_FB_PM2).
148
149config FB_ARMCLCD
150 tristate "ARM PrimeCell PL110 support"
151 depends on FB && ARM && ARM_AMBA
152 select FB_CFB_FILLRECT
153 select FB_CFB_COPYAREA
154 select FB_CFB_IMAGEBLIT
155 select FB_SOFT_CURSOR
156 help
157 This framebuffer device driver is for the ARM PrimeCell PL110
158 Colour LCD controller. ARM PrimeCells provide the building
159 blocks for System on a Chip devices.
160
161 If you want to compile this as a module (=code which can be
162 inserted into and removed from the running kernel), say M
163 here and read <file:Documentation/modules.txt>. The module
164 will be called amba-clcd.
165
166config FB_ACORN
167 bool "Acorn VIDC support"
168 depends on (FB = y) && ARM && (ARCH_ACORN || ARCH_CLPS7500)
169 select FB_CFB_FILLRECT
170 select FB_CFB_COPYAREA
171 select FB_CFB_IMAGEBLIT
172 select FB_SOFT_CURSOR
173 help
174 This is the frame buffer device driver for the Acorn VIDC graphics
175 hardware found in Acorn RISC PCs and other ARM-based machines. If
176 unsure, say N.
177
178config FB_CLPS711X
179 bool "CLPS711X LCD support"
180 depends on (FB = y) && ARM && ARCH_CLPS711X
181 select FB_CFB_FILLRECT
182 select FB_CFB_COPYAREA
183 select FB_CFB_IMAGEBLIT
184 select FB_SOFT_CURSOR
185
186config FB_SA1100
187 bool "SA-1100 LCD support"
188 depends on (FB = y) && ARM && ARCH_SA1100
189 select FB_CFB_FILLRECT
190 select FB_CFB_COPYAREA
191 select FB_CFB_IMAGEBLIT
192 select FB_SOFT_CURSOR
193 help
194 This is a framebuffer device for the SA-1100 LCD Controller.
195 See <http://www.linux-fbdev.org/> for information on framebuffer
196 devices.
197
198 If you plan to use the LCD display with your SA-1100 system, say
199 Y here.
200
Sascha Hauer7c2f891c2005-05-01 08:59:24 -0700201config FB_IMX
202 tristate "Motorola i.MX LCD support"
203 depends on FB && ARM && ARCH_IMX
204 select FB_CFB_FILLRECT
205 select FB_CFB_COPYAREA
206 select FB_CFB_IMAGEBLIT
207 select FB_SOFT_CURSOR
208
Linus Torvalds1da177e2005-04-16 15:20:36 -0700209config FB_CYBER2000
210 tristate "CyberPro 2000/2010/5000 support"
211 depends on FB && PCI && (BROKEN || !SPARC64)
212 select FB_CFB_FILLRECT
213 select FB_CFB_COPYAREA
214 select FB_CFB_IMAGEBLIT
215 select FB_SOFT_CURSOR
216 help
217 This enables support for the Integraphics CyberPro 20x0 and 5000
218 VGA chips used in the Rebel.com Netwinder and other machines.
219 Say Y if you have a NetWinder or a graphics card containing this
220 device, otherwise say N.
221
222config FB_APOLLO
223 bool
224 depends on (FB = y) && APOLLO
225 default y
226 select FB_CFB_FILLRECT
227 select FB_CFB_IMAGEBLIT
228 select FB_SOFT_CURSOR
229
230config FB_Q40
231 bool
232 depends on (FB = y) && Q40
233 default y
234 select FB_CFB_FILLRECT
235 select FB_CFB_COPYAREA
236 select FB_CFB_IMAGEBLIT
237 select FB_SOFT_CURSOR
238
239config FB_AMIGA
240 tristate "Amiga native chipset support"
241 depends on FB && AMIGA
242 select FB_SOFT_CURSOR
243 help
244 This is the frame buffer device driver for the builtin graphics
245 chipset found in Amigas.
246
247 To compile this driver as a module, choose M here: the
248 module will be called amifb.
249
250config FB_AMIGA_OCS
251 bool "Amiga OCS chipset support"
252 depends on FB_AMIGA
253 help
254 This enables support for the original Agnus and Denise video chips,
255 found in the Amiga 1000 and most A500's and A2000's. If you intend
256 to run Linux on any of these systems, say Y; otherwise say N.
257
258config FB_AMIGA_ECS
259 bool "Amiga ECS chipset support"
260 depends on FB_AMIGA
261 help
262 This enables support for the Enhanced Chip Set, found in later
263 A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
264 you intend to run Linux on any of these systems, say Y; otherwise
265 say N.
266
267config FB_AMIGA_AGA
268 bool "Amiga AGA chipset support"
269 depends on FB_AMIGA
270 help
271 This enables support for the Advanced Graphics Architecture (also
272 known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
273 and CD32. If you intend to run Linux on any of these systems, say Y;
274 otherwise say N.
275
276config FB_CYBER
277 tristate "Amiga CyberVision 64 support"
278 depends on FB && ZORRO && BROKEN
279 select FB_CFB_FILLRECT
280 select FB_CFB_COPYAREA
281 select FB_CFB_IMAGEBLIT
282 select FB_SOFT_CURSOR
283 help
284 This enables support for the Cybervision 64 graphics card from
285 Phase5. Please note that its use is not all that intuitive (i.e. if
286 you have any questions, be sure to ask!). Say N unless you have a
287 Cybervision 64 or plan to get one before you next recompile the
288 kernel. Please note that this driver DOES NOT support the
289 Cybervision 64/3D card, as they use incompatible video chips.
290
291config FB_VIRGE
292 bool "Amiga CyberVision 64/3D support "
293 depends on (FB = y) && ZORRO && BROKEN
294 select FB_CFB_FILLRECT
295 select FB_CFB_COPYAREA
296 select FB_CFB_IMAGEBLIT
297 select FB_SOFT_CURSOR
298 help
299 This enables support for the Cybervision 64/3D graphics card from
300 Phase5. Please note that its use is not all that intuitive (i.e. if
301 you have any questions, be sure to ask!). Say N unless you have a
302 Cybervision 64/3D or plan to get one before you next recompile the
303 kernel. Please note that this driver DOES NOT support the older
304 Cybervision 64 card, as they use incompatible video chips.
305
306config FB_RETINAZ3
307 tristate "Amiga Retina Z3 support"
308 depends on (FB = y) && ZORRO && BROKEN
309 help
310 This enables support for the Retina Z3 graphics card. Say N unless
311 you have a Retina Z3 or plan to get one before you next recompile
312 the kernel.
313
314config FB_FM2
315 bool "Amiga FrameMaster II/Rainbow II support"
316 depends on (FB = y) && ZORRO
317 select FB_CFB_FILLRECT
318 select FB_CFB_COPYAREA
319 select FB_CFB_IMAGEBLIT
320 select FB_SOFT_CURSOR
321 help
322 This is the frame buffer device driver for the Amiga FrameMaster
323 card from BSC (exhibited 1992 but not shipped as a CBM product).
324
Jaya Kumar1154ea72005-06-21 17:17:04 -0700325config FB_ARC
326 tristate "Arc Monochrome LCD board support"
327 depends on FB && X86
328 select FB_CFB_FILLRECT
329 select FB_CFB_COPYAREA
330 select FB_CFB_IMAGEBLIT
331 select FB_SOFT_CURSOR
332 help
333 This enables support for the Arc Monochrome LCD board. The board
334 is based on the KS-108 lcd controller and is typically a matrix
335 of 2*n chips. This driver was tested with a 128x64 panel. This
336 driver supports it for use with x86 SBCs through a 16 bit GPIO
337 interface (8 bit data, 8 bit control). If you anticpate using
338 this driver, say Y or M; otherwise say N. You must specify the
339 GPIO IO address to be used for setting control and data.
340
Linus Torvalds1da177e2005-04-16 15:20:36 -0700341config FB_ATARI
342 bool "Atari native chipset support"
343 depends on (FB = y) && ATARI && BROKEN
344 help
345 This is the frame buffer device driver for the builtin graphics
346 chipset found in Ataris.
347
348config FB_OF
349 bool "Open Firmware frame buffer device support"
350 depends on (FB = y) && (PPC64 || PPC_OF)
351 select FB_CFB_FILLRECT
352 select FB_CFB_COPYAREA
353 select FB_CFB_IMAGEBLIT
354 select FB_SOFT_CURSOR
355 select FB_MACMODES
356 help
357 Say Y if you want support with Open Firmware for your graphics
358 board.
359
360config FB_CONTROL
361 bool "Apple \"control\" display support"
362 depends on (FB = y) && PPC_PMAC
363 select FB_CFB_FILLRECT
364 select FB_CFB_COPYAREA
365 select FB_CFB_IMAGEBLIT
366 select FB_SOFT_CURSOR
367 select FB_MACMODES
368 help
369 This driver supports a frame buffer for the graphics adapter in the
370 Power Macintosh 7300 and others.
371
372config FB_PLATINUM
373 bool "Apple \"platinum\" display support"
374 depends on (FB = y) && PPC_PMAC
375 select FB_CFB_FILLRECT
376 select FB_CFB_COPYAREA
377 select FB_CFB_IMAGEBLIT
378 select FB_SOFT_CURSOR
379 select FB_MACMODES
380 help
381 This driver supports a frame buffer for the "platinum" graphics
382 adapter in some Power Macintoshes.
383
384config FB_VALKYRIE
385 bool "Apple \"valkyrie\" display support"
386 depends on (FB = y) && (MAC || PPC_PMAC)
387 select FB_CFB_FILLRECT
388 select FB_CFB_COPYAREA
389 select FB_CFB_IMAGEBLIT
390 select FB_SOFT_CURSOR
391 select FB_MACMODES
392 help
393 This driver supports a frame buffer for the "valkyrie" graphics
394 adapter in some Power Macintoshes.
395
396config FB_CT65550
397 bool "Chips 65550 display support"
398 depends on (FB = y) && PPC
399 select FB_CFB_FILLRECT
400 select FB_CFB_COPYAREA
401 select FB_CFB_IMAGEBLIT
402 select FB_SOFT_CURSOR
403 help
404 This is the frame buffer device driver for the Chips & Technologies
405 65550 graphics chip in PowerBooks.
406
407config FB_ASILIANT
408 bool "Chips 69000 display support"
409 depends on (FB = y) && PCI
410 select FB_CFB_FILLRECT
411 select FB_CFB_COPYAREA
412 select FB_CFB_IMAGEBLIT
413 select FB_SOFT_CURSOR
414
415config FB_IMSTT
416 bool "IMS Twin Turbo display support"
417 depends on (FB = y) && PCI
418 select FB_CFB_IMAGEBLIT
419 select FB_SOFT_CURSOR
420 select FB_MACMODES if PPC
421 help
422 The IMS Twin Turbo is a PCI-based frame buffer card bundled with
423 many Macintosh and compatible computers.
424
425config FB_S3TRIO
426 bool "S3 Trio display support"
427 depends on (FB = y) && PPC && BROKEN
428 help
429 If you have a S3 Trio say Y. Say N for S3 Virge.
430
431config FB_VGA16
432 tristate "VGA 16-color graphics support"
433 depends on FB && (X86 || PPC)
434 select FB_CFB_FILLRECT
435 select FB_CFB_COPYAREA
436 select FB_CFB_IMAGEBLIT
437 select FB_SOFT_CURSOR
438 help
439 This is the frame buffer device driver for VGA 16 color graphic
440 cards. Say Y if you have such a card.
441
442 To compile this driver as a module, choose M here: the
443 module will be called vga16fb.
444
445config FB_STI
446 tristate "HP STI frame buffer device support"
447 depends on FB && PARISC
448 select FB_CFB_FILLRECT
449 select FB_CFB_COPYAREA
450 select FB_CFB_IMAGEBLIT
451 select FB_SOFT_CURSOR
452 default y
453 ---help---
454 STI refers to the HP "Standard Text Interface" which is a set of
455 BIOS routines contained in a ROM chip in HP PA-RISC based machines.
456 Enabling this option will implement the linux framebuffer device
457 using calls to the STI BIOS routines for initialisation.
458
459 If you enable this option, you will get a planar framebuffer device
460 /dev/fb which will work on the most common HP graphic cards of the
461 NGLE family, including the artist chips (in the 7xx and Bxxx series),
462 HCRX, HCRX24, CRX, CRX24 and VisEG series.
463
464 It is safe to enable this option, so you should probably say "Y".
465
466config FB_MAC
467 bool "Generic Macintosh display support"
468 depends on (FB = y) && MAC
469 select FB_CFB_FILLRECT
470 select FB_CFB_COPYAREA
471 select FB_CFB_IMAGEBLIT
472 select FB_SOFT_CURSOR
473 select FB_MACMODES
474
475# bool ' Apple DAFB display support' CONFIG_FB_DAFB
476config FB_HP300
477 bool
478 depends on (FB = y) && HP300
479 select FB_CFB_FILLRECT
480 select FB_CFB_IMAGEBLIT
481 select FB_SOFT_CURSOR
482 default y
483
484config FB_TGA
485 tristate "TGA framebuffer support"
486 depends on FB && ALPHA
487 select FB_CFB_FILLRECT
488 select FB_CFB_COPYAREA
489 select FB_CFB_IMAGEBLIT
490 select FB_SOFT_CURSOR
491 help
492 This is the frame buffer device driver for generic TGA graphic
493 cards. Say Y if you have one of those.
494
495config FB_VESA
496 bool "VESA VGA graphics support"
497 depends on (FB = y) && (X86 || X86_64)
498 select FB_CFB_FILLRECT
499 select FB_CFB_COPYAREA
500 select FB_CFB_IMAGEBLIT
501 select FB_SOFT_CURSOR
502 help
503 This is the frame buffer device driver for generic VESA 2.0
504 compliant graphic cards. The older VESA 1.2 cards are not supported.
505 You will get a boot time penguin logo at no additional cost. Please
506 read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
507
508config VIDEO_SELECT
509 bool
510 depends on FB_VESA
511 default y
512
513config FB_HGA
514 tristate "Hercules mono graphics support"
515 depends on FB && X86
516 select FB_CFB_FILLRECT
517 select FB_CFB_COPYAREA
518 select FB_CFB_IMAGEBLIT
519 select FB_SOFT_CURSOR
520 help
521 Say Y here if you have a Hercules mono graphics card.
522
523 To compile this driver as a module, choose M here: the
524 module will be called hgafb.
525
526 As this card technology is 15 years old, most people will answer N
527 here.
528
529config FB_HGA_ACCEL
530 bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
531 depends on FB_HGA && EXPERIMENTAL
532 ---help---
533 This will compile the Hercules mono graphics with
534 acceleration functions.
535
536
537config VIDEO_SELECT
538 bool
539 depends on (FB = y) && X86
540 default y
541
542config FB_SGIVW
543 tristate "SGI Visual Workstation framebuffer support"
544 depends on FB && X86_VISWS
545 select FB_CFB_FILLRECT
546 select FB_CFB_COPYAREA
547 select FB_CFB_IMAGEBLIT
548 select FB_SOFT_CURSOR
549 help
550 SGI Visual Workstation support for framebuffer graphics.
551
552config FB_GBE
553 bool "SGI Graphics Backend frame buffer support"
554 depends on (FB = y) && (SGI_IP32 || X86_VISWS)
555 select FB_CFB_FILLRECT
556 select FB_CFB_COPYAREA
557 select FB_CFB_IMAGEBLIT
558 select FB_SOFT_CURSOR
559 help
560 This is the frame buffer device driver for SGI Graphics Backend.
561 This chip is used in SGI O2 and Visual Workstation 320/540.
562
563config FB_GBE_MEM
564 int "Video memory size in MB"
565 depends on FB_GBE
566 default 8
567 help
568 This is the amount of memory reserved for the framebuffer,
569 which can be any value between 1MB and 8MB.
570
571config BUS_I2C
572 bool
573 depends on (FB = y) && VISWS
574 default y
575
576config FB_SUN3
577 bool "Sun3 framebuffer support"
578 depends on (FB = y) && (SUN3 || SUN3X) && BROKEN
579
580config FB_BW2
581 bool "BWtwo support"
582 depends on (FB = y) && ((SPARC32 || SPARC64) && FB_SBUS || (SUN3 || SUN3X) && FB_SUN3)
583 select FB_CFB_FILLRECT
584 select FB_CFB_COPYAREA
585 select FB_CFB_IMAGEBLIT
586 select FB_SOFT_CURSOR
587 help
588 This is the frame buffer device driver for the BWtwo frame buffer.
589
590config FB_CG3
591 bool "CGthree support"
592 depends on (FB = y) && ((SPARC32 || SPARC64) && FB_SBUS || (SUN3 || SUN3X) && FB_SUN3)
593 select FB_CFB_COPYAREA
594 select FB_CFB_IMAGEBLIT
595 select FB_SOFT_CURSOR
596 help
597 This is the frame buffer device driver for the CGthree frame buffer.
598
599config FB_CG6
600 bool "CGsix (GX,TurboGX) support"
601 depends on (FB = y) && ((SPARC32 || SPARC64) && FB_SBUS || (SUN3 || SUN3X) && FB_SUN3)
602 select FB_CFB_COPYAREA
603 select FB_CFB_IMAGEBLIT
604 select FB_SOFT_CURSOR
605 help
606 This is the frame buffer device driver for the CGsix (GX, TurboGX)
607 frame buffer.
608
609config FB_PVR2
610 tristate "NEC PowerVR 2 display support"
611 depends on FB && SH_DREAMCAST
612 select FB_CFB_FILLRECT
613 select FB_CFB_COPYAREA
614 select FB_CFB_IMAGEBLIT
615 select FB_SOFT_CURSOR
616 ---help---
617 Say Y here if you have a PowerVR 2 card in your box. If you plan to
618 run linux on your Dreamcast, you will have to say Y here.
619 This driver may or may not work on other PowerVR 2 cards, but is
620 totally untested. Use at your own risk. If unsure, say N.
621
622 To compile this driver as a module, choose M here: the
623 module will be called pvr2fb.
624
625 You can pass several parameters to the driver at boot time or at
626 module load time. The parameters look like "video=pvr2:XXX", where
627 the meaning of XXX can be found at the end of the main source file
628 (<file:drivers/video/pvr2fb.c>). Please see the file
629 <file:Documentation/fb/pvr2fb.txt>.
630
631config FB_EPSON1355
632 bool "Epson 1355 framebuffer support"
633 depends on (FB = y) && (SUPERH || ARCH_CEIVA)
634 select FB_CFB_FILLRECT
635 select FB_CFB_COPYAREA
636 select FB_CFB_IMAGEBLIT
637 select FB_SOFT_CURSOR
638 help
639 Build in support for the SED1355 Epson Research Embedded RAMDAC
640 LCD/CRT Controller (since redesignated as the S1D13505) as a
641 framebuffer. Product specs at
642 <http://www.erd.epson.com/vdc/html/products.htm>.
643
644config FB_NVIDIA
645 tristate "nVidia Framebuffer Support"
646 depends on FB && PCI
647 select I2C_ALGOBIT if FB_NVIDIA_I2C
648 select I2C if FB_NVIDIA_I2C
649 select FB_MODE_HELPERS
650 select FB_CFB_FILLRECT
651 select FB_CFB_COPYAREA
652 select FB_CFB_IMAGEBLIT
653 select FB_SOFT_CURSOR
654 help
655 This driver supports graphics boards with the nVidia chips, TNT
656 and newer. For very old chipsets, such as the RIVA128, then use
657 the rivafb.
658 Say Y if you have such a graphics board.
659
660 To compile this driver as a module, choose M here: the
661 module will be called nvidiafb.
662
663config FB_NVIDIA_I2C
664 bool "Enable DDC Support"
665 depends on FB_NVIDIA && !PPC_OF
666 help
667 This enables I2C support for nVidia Chipsets. This is used
668 only for getting EDID information from the attached display
669 allowing for robust video mode handling and switching.
670
671 Because fbdev-2.6 requires that drivers must be able to
672 independently validate video mode parameters, you should say Y
673 here.
674
675config FB_RIVA
676 tristate "nVidia Riva support"
677 depends on FB && PCI
678 select I2C_ALGOBIT if FB_RIVA_I2C
679 select I2C if FB_RIVA_I2C
680 select FB_MODE_HELPERS
681 select FB_CFB_FILLRECT
682 select FB_CFB_COPYAREA
683 select FB_CFB_IMAGEBLIT
684 select FB_SOFT_CURSOR
685 help
686 This driver supports graphics boards with the nVidia Riva/Geforce
687 chips.
688 Say Y if you have such a graphics board.
689
690 To compile this driver as a module, choose M here: the
691 module will be called rivafb.
692
693config FB_RIVA_I2C
694 bool "Enable DDC Support"
695 depends on FB_RIVA
696 help
697 This enables I2C support for nVidia Chipsets. This is used
698 only for getting EDID information from the attached display
699 allowing for robust video mode handling and switching.
700
701 Because fbdev-2.6 requires that drivers must be able to
702 independently validate video mode parameters, you should say Y
703 here.
704
705config FB_RIVA_DEBUG
706 bool "Lots of debug output from Riva(nVidia) driver"
707 depends on FB_RIVA
708 default n
709 help
710 Say Y here if you want the Riva driver to output all sorts
711 of debugging informations to provide to the maintainer when
712 something goes wrong.
713
714config FB_I810
715 tristate "Intel 810/815 support (EXPERIMENTAL)"
716 depends on FB && EXPERIMENTAL && PCI && X86 && !X86_64
717 select AGP
718 select AGP_INTEL
719 select FB_MODE_HELPERS
720 select FB_CFB_FILLRECT
721 select FB_CFB_COPYAREA
722 select FB_CFB_IMAGEBLIT
723 select FB_SOFT_CURSOR
724 help
725 This driver supports the on-board graphics built in to the Intel 810
726 and 815 chipsets. Say Y if you have and plan to use such a board.
727
728 To compile this driver as a module, choose M here: the
729 module will be called i810fb.
730
731 For more information, please read
732 <file:Documentation/fb/intel810.txt>
733
734config FB_I810_GTF
735 bool "use VESA Generalized Timing Formula"
736 depends on FB_I810
737 help
738 If you say Y, then the VESA standard, Generalized Timing Formula
739 or GTF, will be used to calculate the required video timing values
740 per video mode. Since the GTF allows nondiscrete timings
741 (nondiscrete being a range of values as opposed to discrete being a
742 set of values), you'll be able to use any combination of horizontal
743 and vertical resolutions, and vertical refresh rates without having
744 to specify your own timing parameters. This is especially useful
745 to maximize the performance of an aging display, or if you just
746 have a display with nonstandard dimensions. A VESA compliant
747 monitor is recommended, but can still work with non-compliant ones.
748 If you need or want this, then select this option. The timings may
749 not be compliant with Intel's recommended values. Use at your own
750 risk.
751
752 If you say N, the driver will revert to discrete video timings
753 using a set recommended by Intel in their documentation.
754
755 If unsure, say N.
756
757config FB_INTEL
758 tristate "Intel 830M/845G/852GM/855GM/865G support (EXPERIMENTAL)"
759 depends on FB && EXPERIMENTAL && PCI && X86 && !X86_64
760 select AGP
761 select AGP_INTEL
762 select FB_MODE_HELPERS
763 select FB_CFB_FILLRECT
764 select FB_CFB_COPYAREA
765 select FB_CFB_IMAGEBLIT
766 select FB_SOFT_CURSOR
767 help
768 This driver supports the on-board graphics built in to the Intel
769 830M/845G/852GM/855GM/865G chipsets.
770 Say Y if you have and plan to use such a board.
771
772 To compile this driver as a module, choose M here: the
773 module will be called intelfb.
774
775config FB_INTEL_DEBUG
776 bool "Intel driver Debug Messages"
777 depends on FB_INTEL
778 ---help---
779 Say Y here if you want the Intel driver to output all sorts
780 of debugging informations to provide to the maintainer when
781 something goes wrong.
782
783config FB_MATROX
784 tristate "Matrox acceleration"
785 depends on FB && PCI
786 select FB_CFB_FILLRECT
787 select FB_CFB_COPYAREA
788 select FB_CFB_IMAGEBLIT
789 select FB_SOFT_CURSOR
790 select FB_TILEBLITTING
791 select FB_MACMODES if PPC_PMAC
792 ---help---
793 Say Y here if you have a Matrox Millennium, Matrox Millennium II,
794 Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
795 Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
796 Matrox G400, G450 or G550 card in your box.
797
798 To compile this driver as a module, choose M here: the
799 module will be called matroxfb.
800
801 You can pass several parameters to the driver at boot time or at
802 module load time. The parameters look like "video=matrox:XXX", and
803 are described in <file:Documentation/fb/matroxfb.txt>.
804
805config FB_MATROX_MILLENIUM
806 bool "Millennium I/II support"
807 depends on FB_MATROX
808 help
809 Say Y here if you have a Matrox Millennium or Matrox Millennium II
810 video card. If you select "Advanced lowlevel driver options" below,
811 you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
812 packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
813 also use font widths different from 8.
814
815config FB_MATROX_MYSTIQUE
816 bool "Mystique support"
817 depends on FB_MATROX
818 help
819 Say Y here if you have a Matrox Mystique or Matrox Mystique 220
820 video card. If you select "Advanced lowlevel driver options" below,
821 you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
822 packed pixel and 32 bpp packed pixel. You can also use font widths
823 different from 8.
824
825config FB_MATROX_G
826 bool "G100/G200/G400/G450/G550 support"
827 depends on FB_MATROX
828 ---help---
829 Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
830 video card. If you select "Advanced lowlevel driver options", you
831 should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
832 pixel and 32 bpp packed pixel. You can also use font widths
833 different from 8.
834
835 If you need support for G400 secondary head, you must first say Y to
836 "I2C support" in the character devices section, and then to
837 "Matrox I2C support" and "G400 second head support" here in the
838 framebuffer section. G450/G550 secondary head and digital output
839 are supported without additional modules.
840
841 The driver starts in monitor mode. You must use the matroxset tool
842 (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
843 swap primary and secondary head outputs, or to change output mode.
844 Secondary head driver always start in 640x480 resolution and you
845 must use fbset to change it.
846
847 Do not forget that second head supports only 16 and 32 bpp
848 packed pixels, so it is a good idea to compile them into the kernel
849 too. You can use only some font widths, as the driver uses generic
850 painting procedures (the secondary head does not use acceleration
851 engine).
852
853 G450/G550 hardware can display TV picture only from secondary CRTC,
854 and it performs no scaling, so picture must have 525 or 625 lines.
855
856config FB_MATROX_I2C
857 tristate "Matrox I2C support"
858 depends on FB_MATROX && I2C
859 select I2C_ALGOBIT
860 ---help---
861 This drivers creates I2C buses which are needed for accessing the
862 DDC (I2C) bus present on all Matroxes, an I2C bus which
863 interconnects Matrox optional devices, like MGA-TVO on G200 and
864 G400, and the secondary head DDC bus, present on G400 only.
865
866 You can say Y or M here if you want to experiment with monitor
867 detection code. You must say Y or M here if you want to use either
868 second head of G400 or MGA-TVO on G200 or G400.
869
870 If you compile it as module, it will create a module named
871 i2c-matroxfb.
872
873config FB_MATROX_MAVEN
874 tristate "G400 second head support"
875 depends on FB_MATROX_G && FB_MATROX_I2C
876 ---help---
877 WARNING !!! This support does not work with G450 !!!
878
879 Say Y or M here if you want to use a secondary head (meaning two
880 monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
881 head is not compatible with accelerated XFree 3.3.x SVGA servers -
882 secondary head output is blanked while you are in X. With XFree
883 3.9.17 preview you can use both heads if you use SVGA over fbdev or
884 the fbdev driver on first head and the fbdev driver on second head.
885
886 If you compile it as module, two modules are created,
887 matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
888 both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
889 also load i2c-matroxfb to get it to run.
890
891 The driver starts in monitor mode and you must use the matroxset
892 tool (available at
893 <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
894 PAL or NTSC or to swap primary and secondary head outputs.
895 Secondary head driver also always start in 640x480 resolution, you
896 must use fbset to change it.
897
898 Also do not forget that second head supports only 16 and 32 bpp
899 packed pixels, so it is a good idea to compile them into the kernel
900 too. You can use only some font widths, as the driver uses generic
901 painting procedures (the secondary head does not use acceleration
902 engine).
903
904config FB_MATROX_MULTIHEAD
905 bool "Multihead support"
906 depends on FB_MATROX
907 ---help---
908 Say Y here if you have more than one (supported) Matrox device in
909 your computer and you want to use all of them for different monitors
910 ("multihead"). If you have only one device, you should say N because
911 the driver compiled with Y is larger and a bit slower, especially on
912 ia32 (ix86).
913
914 If you said M to "Matrox unified accelerated driver" and N here, you
915 will still be able to use several Matrox devices simultaneously:
916 insert several instances of the module matroxfb into the kernel
917 with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
918 for the different Matrox devices. This method is slightly faster but
919 uses 40 KB of kernel memory per Matrox card.
920
921 There is no need for enabling 'Matrox multihead support' if you have
922 only one Matrox card in the box.
923
924config FB_RADEON_OLD
925 tristate "ATI Radeon display support (Old driver)"
926 depends on FB && PCI
927 select FB_CFB_FILLRECT
928 select FB_CFB_COPYAREA
929 select FB_CFB_IMAGEBLIT
930 select FB_SOFT_CURSOR
931 select FB_MACMODES if PPC
932 help
933 Choose this option if you want to use an ATI Radeon graphics card as
934 a framebuffer device. There are both PCI and AGP versions. You
935 don't need to choose this to run the Radeon in plain VGA mode.
936 There is a product page at
937 <http://www.ati.com/na/pages/products/pc/radeon32/index.html>.
938
939config FB_RADEON
940 tristate "ATI Radeon display support"
941 depends on FB && PCI
942 select I2C_ALGOBIT if FB_RADEON_I2C
943 select I2C if FB_RADEON_I2C
944 select FB_MODE_HELPERS
945 select FB_CFB_FILLRECT
946 select FB_CFB_COPYAREA
947 select FB_CFB_IMAGEBLIT
948 select FB_SOFT_CURSOR
949 select FB_MACMODES if PPC_OF
950 help
951 Choose this option if you want to use an ATI Radeon graphics card as
952 a framebuffer device. There are both PCI and AGP versions. You
953 don't need to choose this to run the Radeon in plain VGA mode.
954
955 If you say Y here and want DDC/I2C support you must first say Y to
956 "I2C support" and "I2C bit-banging support" in the character devices
957 section.
958
959 If you say M here then "I2C support" and "I2C bit-banging support"
960 can be build either as modules or built-in.
961
962 There is a product page at
963 <http://www.ati.com/na/pages/products/pc/radeon32/index.html>.
964
965config FB_RADEON_I2C
966 bool "DDC/I2C for ATI Radeon support"
967 depends on FB_RADEON
968 default y
969 help
970 Say Y here if you want DDC/I2C support for your Radeon board.
971
972config FB_RADEON_DEBUG
973 bool "Lots of debug output from Radeon driver"
974 depends on FB_RADEON
975 default n
976 help
977 Say Y here if you want the Radeon driver to output all sorts
978 of debugging informations to provide to the maintainer when
979 something goes wrong.
980
981config FB_ATY128
982 tristate "ATI Rage128 display support"
983 depends on FB && PCI
984 select FB_CFB_FILLRECT
985 select FB_CFB_COPYAREA
986 select FB_CFB_IMAGEBLIT
987 select FB_SOFT_CURSOR
988 select FB_MACMODES if PPC_PMAC
989 help
990 This driver supports graphics boards with the ATI Rage128 chips.
991 Say Y if you have such a graphics board and read
992 <file:Documentation/fb/aty128fb.txt>.
993
994 To compile this driver as a module, choose M here: the
995 module will be called aty128fb.
996
997config FB_ATY
998 tristate "ATI Mach64 display support" if PCI || ATARI
999 depends on FB
1000 select FB_CFB_FILLRECT
1001 select FB_CFB_COPYAREA
1002 select FB_CFB_IMAGEBLIT
1003 select FB_SOFT_CURSOR
1004 select FB_MACMODES if PPC
1005 help
1006 This driver supports graphics boards with the ATI Mach64 chips.
1007 Say Y if you have such a graphics board.
1008
1009 To compile this driver as a module, choose M here: the
1010 module will be called atyfb.
1011
1012config FB_ATY_CT
1013 bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1014 depends on PCI && FB_ATY
1015 default y if SPARC64 && FB_PCI
1016 help
1017 Say Y here to support use of ATI's 64-bit Rage boards (or other
1018 boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1019 framebuffer device. The ATI product support page for these boards
1020 is at <http://support.ati.com/products/pc/mach64/>.
1021
1022config FB_ATY_GENERIC_LCD
1023 bool "Mach64 generic LCD support (EXPERIMENTAL)"
1024 depends on FB_ATY_CT
1025 help
1026 Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1027 Rage XC, or Rage XL chipset.
1028
1029config FB_ATY_XL_INIT
1030 bool "Rage XL No-BIOS Init support"
1031 depends on FB_ATY_CT
1032 help
1033 Say Y here to support booting a Rage XL without BIOS support.
1034
1035config FB_ATY_GX
1036 bool "Mach64 GX support" if PCI
1037 depends on FB_ATY
1038 default y if ATARI
1039 help
1040 Say Y here to support use of the ATI Mach64 Graphics Expression
1041 board (or other boards based on the Mach64 GX chipset) as a
1042 framebuffer device. The ATI product support page for these boards
1043 is at
1044 <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1045
1046config FB_SAVAGE
1047 tristate "S3 Savage support"
1048 depends on FB && PCI && EXPERIMENTAL
1049 select I2C_ALGOBIT if FB_SAVAGE_I2C
1050 select I2C if FB_SAVAGE_I2C
1051 select FB_MODE_HELPERS
1052 select FB_CFB_FILLRECT
1053 select FB_CFB_COPYAREA
1054 select FB_CFB_IMAGEBLIT
1055 select FB_SOFT_CURSOR
1056 help
1057 This driver supports notebooks and computers with S3 Savage PCI/AGP
1058 chips.
1059
1060 Say Y if you have such a graphics card.
1061
1062 To compile this driver as a module, choose M here; the module
1063 will be called savagefb.
1064
1065config FB_SAVAGE_I2C
1066 bool "Enable DDC2 Support"
1067 depends on FB_SAVAGE
1068 help
1069 This enables I2C support for S3 Savage Chipsets. This is used
1070 only for getting EDID information from the attached display
1071 allowing for robust video mode handling and switching.
1072
1073 Because fbdev-2.6 requires that drivers must be able to
1074 independently validate video mode parameters, you should say Y
1075 here.
1076
1077config FB_SAVAGE_ACCEL
1078 bool "Enable Console Acceleration"
1079 depends on FB_SAVAGE
1080 default n
1081 help
1082 This option will compile in console acceleration support. If
1083 the resulting framebuffer console has bothersome glitches, then
1084 choose N here.
1085
1086config FB_SIS
1087 tristate "SiS acceleration"
1088 depends on FB && PCI
1089 select FB_CFB_FILLRECT
1090 select FB_CFB_COPYAREA
1091 select FB_CFB_IMAGEBLIT
1092 select FB_SOFT_CURSOR
1093 help
1094 This is the frame buffer device driver for the SiS 300, 315 and
1095 330 series VGA chipsets. Specs available at <http://www.sis.com>
1096
1097 To compile this driver as a module, choose M here; the module
1098 will be called sisfb.
1099
1100config FB_SIS_300
1101 bool "SiS 300 series support"
1102 depends on FB_SIS
1103 help
1104 Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1105
1106config FB_SIS_315
1107 bool "SiS 315/330 series support"
1108 depends on FB_SIS
1109 help
1110 Say Y here to support use of the SiS 315 and 330 series
1111 (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760).
1112
1113config FB_NEOMAGIC
1114 tristate "NeoMagic display support"
1115 depends on FB && PCI
1116 select FB_MODE_HELPERS
1117 select FB_CFB_FILLRECT
1118 select FB_CFB_COPYAREA
1119 select FB_CFB_IMAGEBLIT
1120 select FB_SOFT_CURSOR
1121 help
1122 This driver supports notebooks with NeoMagic PCI chips.
1123 Say Y if you have such a graphics card.
1124
1125 To compile this driver as a module, choose M here: the
1126 module will be called neofb.
1127
1128config FB_KYRO
1129 tristate "IMG Kyro support"
1130 depends on FB && PCI
1131 select FB_CFB_FILLRECT
1132 select FB_CFB_COPYAREA
1133 select FB_CFB_IMAGEBLIT
1134 select FB_SOFT_CURSOR
1135 help
1136 Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1137 graphics board.
1138
1139 To compile this driver as a module, choose M here: the
1140 module will be called kyrofb.
1141
1142config FB_3DFX
1143 tristate "3Dfx Banshee/Voodoo3 display support"
1144 depends on FB && PCI
1145 select FB_CFB_IMAGEBLIT
1146 select FB_CFB_FILLRECT
1147 select FB_CFB_COPYAREA
1148 select FB_SOFT_CURSOR
1149 help
1150 This driver supports graphics boards with the 3Dfx Banshee/Voodoo3
1151 chips. Say Y if you have such a graphics board.
1152
1153 To compile this driver as a module, choose M here: the
1154 module will be called tdfxfb.
1155
1156config FB_3DFX_ACCEL
1157 bool "3Dfx Banshee/Voodoo3 Acceleration functions (EXPERIMENTAL)"
1158 depends on FB_3DFX && EXPERIMENTAL
1159 ---help---
1160 This will compile the 3Dfx Banshee/Voodoo3 frame buffer device
1161 with acceleration functions.
1162
1163
1164config FB_VOODOO1
1165 tristate "3Dfx Voodoo Graphics (sst1) support"
1166 depends on FB && PCI
1167 select FB_CFB_FILLRECT
1168 select FB_CFB_COPYAREA
1169 select FB_CFB_IMAGEBLIT
1170 select FB_SOFT_CURSOR
1171 ---help---
1172 Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
1173 Voodoo2 (cvg) based graphics card.
1174
1175 To compile this driver as a module, choose M here: the
1176 module will be called sstfb.
1177
1178 WARNING: Do not use any application that uses the 3D engine
1179 (namely glide) while using this driver.
1180 Please read the <file:Documentation/fb/README-sstfb.txt> for supported
1181 options and other important info support.
1182
1183config FB_TRIDENT
1184 tristate "Trident support"
1185 depends on FB && PCI
1186 select FB_CFB_FILLRECT
1187 select FB_CFB_COPYAREA
1188 select FB_CFB_IMAGEBLIT
1189 select FB_SOFT_CURSOR
1190 ---help---
1191 This driver is supposed to support graphics boards with the
1192 Trident CyberXXXX/Image/CyberBlade chips mostly found in laptops
1193 but also on some motherboards. For more information, read
1194 <file:Documentation/fb/tridentfb.txt>
1195
1196 Say Y if you have such a graphics board.
1197
1198 To compile this driver as a module, choose M here: the
1199 module will be called tridentfb.
1200
1201config FB_TRIDENT_ACCEL
1202 bool "Trident Acceleration functions (EXPERIMENTAL)"
1203 depends on FB_TRIDENT && EXPERIMENTAL
1204 ---help---
1205 This will compile the Trident frame buffer device with
1206 acceleration functions.
1207
1208
1209config FB_PM3
1210 tristate "Permedia3 support"
1211 depends on FB && PCI && BROKEN
1212 help
1213 This is the frame buffer device driver for the 3DLabs Permedia3
1214 chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1215 similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1216 and maybe other boards.
1217
1218config FB_E1356
1219 tristate "Epson SED1356 framebuffer support"
1220 depends on FB && EXPERIMENTAL && PCI && MIPS
1221
1222config PB1000_CRT
1223 bool "Use CRT on Pb1000 (J65)"
1224 depends on MIPS_PB1000=y && FB_E1356
1225
1226config PB1000_NTSC
1227 bool "Use Compsite NTSC on Pb1000 (J63)"
1228 depends on MIPS_PB1000=y && FB_E1356
1229
1230config PB1000_TFT
1231 bool "Use TFT Panel on Pb1000 (J64)"
1232 depends on MIPS_PB1000=y && FB_E1356
1233
1234config PB1500_CRT
1235 bool "Use CRT on Pb1500 " if MIPS_PB1500=y
1236 depends on FB_E1356
1237
1238config PB1500_CRT
1239 prompt "Use CRT on Pb1100 "
1240 depends on FB_E1356 && MIPS_PB1100=y
1241
1242config PB1500_TFT
1243 bool "Use TFT Panel on Pb1500 " if MIPS_PB1500=y
1244 depends on FB_E1356
1245
1246config PB1500_TFT
1247 prompt "Use TFT Panel on Pb1100 "
1248 depends on FB_E1356 && MIPS_PB1100=y
1249
1250config FB_AU1100
1251 bool "Au1100 LCD Driver"
1252 depends on (FB = y) && EXPERIMENTAL && PCI && MIPS && MIPS_PB1100=y
1253
1254source "drivers/video/geode/Kconfig"
1255
1256config FB_SBUS
1257 bool "SBUS and UPA framebuffers"
1258 depends on (FB = y) && (SPARC32 || SPARC64)
1259 help
1260 Say Y if you want support for SBUS or UPA based frame buffer device.
1261
1262config FB_FFB
1263 bool "Creator/Creator3D/Elite3D support"
1264 depends on FB_SBUS && SPARC64
1265 select FB_CFB_COPYAREA
1266 select FB_CFB_IMAGEBLIT
1267 select FB_SOFT_CURSOR
1268 help
1269 This is the frame buffer device driver for the Creator, Creator3D,
1270 and Elite3D graphics boards.
1271
1272config FB_TCX
1273 bool "TCX (SS4/SS5 only) support"
1274 depends on FB_SBUS
1275 select FB_CFB_FILLRECT
1276 select FB_CFB_COPYAREA
1277 select FB_CFB_IMAGEBLIT
1278 select FB_SOFT_CURSOR
1279 help
1280 This is the frame buffer device driver for the TCX 24/8bit frame
1281 buffer.
1282
1283config FB_CG14
1284 bool "CGfourteen (SX) support"
1285 depends on FB_SBUS
1286 select FB_CFB_FILLRECT
1287 select FB_CFB_COPYAREA
1288 select FB_CFB_IMAGEBLIT
1289 select FB_SOFT_CURSOR
1290 help
1291 This is the frame buffer device driver for the CGfourteen frame
1292 buffer on Desktop SPARCsystems with the SX graphics option.
1293
1294config FB_P9100
1295 bool "P9100 (Sparcbook 3 only) support"
1296 depends on FB_SBUS
1297 select FB_CFB_FILLRECT
1298 select FB_CFB_COPYAREA
1299 select FB_CFB_IMAGEBLIT
1300 select FB_SOFT_CURSOR
1301 help
1302 This is the frame buffer device driver for the P9100 card
1303 supported on Sparcbook 3 machines.
1304
1305config FB_LEO
1306 bool "Leo (ZX) support"
1307 depends on FB_SBUS
1308 select FB_CFB_FILLRECT
1309 select FB_CFB_COPYAREA
1310 select FB_CFB_IMAGEBLIT
1311 select FB_SOFT_CURSOR
1312 help
1313 This is the frame buffer device driver for the SBUS-based Sun ZX
1314 (leo) frame buffer cards.
1315
1316config FB_PCI
1317 bool "PCI framebuffers"
1318 depends on (FB = y) && PCI && (SPARC64 || SPARC32)
1319
1320config FB_IGA
1321 bool "IGA 168x display support"
1322 depends on SPARC32 && FB_PCI
1323 select FB_CFB_FILLRECT
1324 select FB_CFB_COPYAREA
1325 select FB_CFB_IMAGEBLIT
1326 select FB_SOFT_CURSOR
1327 help
1328 This is the framebuffer device for the INTERGRAPHICS 1680 and
1329 successor frame buffer cards.
1330
1331config FB_HIT
1332 tristate "HD64461 Frame Buffer support"
1333 depends on FB && HD64461
1334 select FB_CFB_FILLRECT
1335 select FB_CFB_COPYAREA
1336 select FB_CFB_IMAGEBLIT
1337 select FB_SOFT_CURSOR
1338 help
1339 This is the frame buffer device driver for the Hitachi HD64461 LCD
1340 frame buffer card.
1341
1342config FB_PMAG_AA
1343 bool "PMAG-AA TURBOchannel framebuffer support"
1344 depends on (FB = y) && MACH_DECSTATION && TC
1345 select FB_CFB_FILLRECT
1346 select FB_CFB_COPYAREA
1347 select FB_CFB_IMAGEBLIT
1348 select FB_SOFT_CURSOR
1349 help
1350 Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1351 used mainly in the MIPS-based DECstation series.
1352
1353config FB_PMAG_BA
1354 bool "PMAG-BA TURBOchannel framebuffer support"
1355 depends on (FB = y) && MACH_DECSTATION && TC
1356 select FB_CFB_FILLRECT
1357 select FB_CFB_COPYAREA
1358 select FB_CFB_IMAGEBLIT
1359 select FB_SOFT_CURSOR
1360 help
1361 Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1362 used mainly in the MIPS-based DECstation series.
1363
1364config FB_PMAGB_B
1365 bool "PMAGB-B TURBOchannel framebuffer support"
1366 depends on (FB = y) && MACH_DECSTATION && TC
1367 select FB_CFB_FILLRECT
1368 select FB_CFB_COPYAREA
1369 select FB_CFB_IMAGEBLIT
1370 select FB_SOFT_CURSOR
1371 help
1372 Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1373 in the MIPS-based DECstation series. The card is currently only
1374 supported in 1280x1024x8 mode.
1375
1376config FB_MAXINE
1377 bool "Maxine (Personal DECstation) onboard framebuffer support"
1378 depends on (FB = y) && MACH_DECSTATION && TC
1379 select FB_CFB_FILLRECT
1380 select FB_CFB_COPYAREA
1381 select FB_CFB_IMAGEBLIT
1382 select FB_SOFT_CURSOR
1383 help
1384 Support for the onboard framebuffer (1024x768x8) in the Personal
1385 DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1386 Codename "Maxine").
1387
1388config FB_TX3912
1389 bool "TMPTX3912/PR31700 frame buffer support"
1390 depends on (FB = y) && NINO
1391 select FB_CFB_FILLRECT
1392 select FB_CFB_COPYAREA
1393 select FB_CFB_IMAGEBLIT
1394 select FB_SOFT_CURSOR
1395 help
1396 The TX3912 is a Toshiba RISC processor based on the MIPS 3900 core
1397 see <http://www.toshiba.com/taec/components/Generic/risc/tx3912.htm>.
1398
1399 Say Y here to enable kernel support for the on-board framebuffer.
1400
1401config FB_G364
Yoichi Yuasab38817d2005-07-27 11:43:28 -07001402 bool "G364 frame buffer support"
1403 depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001404 select FB_CFB_FILLRECT
1405 select FB_CFB_COPYAREA
1406 select FB_CFB_IMAGEBLIT
1407 select FB_SOFT_CURSOR
1408 help
1409 The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1410 Olivetti M700-10 systems.
1411
1412config FB_68328
1413 bool "Motorola 68328 native frame buffer support"
1414 depends on FB && (M68328 || M68EZ328 || M68VZ328)
1415 select FB_CFB_FILLRECT
1416 select FB_CFB_COPYAREA
1417 select FB_CFB_IMAGEBLIT
1418 select FB_SOFT_CURSOR
1419 help
1420 Say Y here if you want to support the built-in frame buffer of
1421 the Motorola 68328 CPU family.
1422
1423config FB_PXA
1424 tristate "PXA LCD framebuffer support"
1425 depends on FB && ARCH_PXA
1426 select FB_CFB_FILLRECT
1427 select FB_CFB_COPYAREA
1428 select FB_CFB_IMAGEBLIT
1429 select FB_SOFT_CURSOR
1430 ---help---
1431 Frame buffer driver for the built-in LCD controller in the Intel
1432 PXA2x0 processor.
1433
1434 This driver is also available as a module ( = code which can be
1435 inserted and removed from the running kernel whenever you want). The
1436 module will be called vfb. If you want to compile it as a module,
1437 say M here and read <file:Documentation/modules.txt>.
1438
1439 If unsure, say N.
1440
1441config FB_W100
1442 tristate "W100 frame buffer support"
1443 depends on FB && PXA_SHARPSL
1444 select FB_CFB_FILLRECT
1445 select FB_CFB_COPYAREA
1446 select FB_CFB_IMAGEBLIT
1447 select FB_SOFT_CURSOR
1448 ---help---
1449 Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1450
1451 This driver is also available as a module ( = code which can be
1452 inserted and removed from the running kernel whenever you want). The
1453 module will be called vfb. If you want to compile it as a module,
1454 say M here and read <file:Documentation/modules.txt>.
1455
1456 If unsure, say N.
1457
1458config FB_PXA_PARAMETERS
1459 bool "PXA LCD command line parameters"
1460 default n
1461 depends on FB_PXA
1462 ---help---
1463 Enable the use of kernel command line or module parameters
1464 to configure the physical properties of the LCD panel when
1465 using the PXA LCD driver.
1466
1467 This option allows you to override the panel parameters
1468 supplied by the platform in order to support multiple
1469 different models of flatpanel. If you will only be using a
1470 single model of flatpanel then you can safely leave this
1471 option disabled.
1472
1473 <file:Documentation/fb/pxafb.txt> describes the available parameters.
1474
1475config FB_S1D13XXX
1476 tristate "Epson S1D13XXX framebuffer support"
1477 depends on FB
1478 select FB_CFB_FILLRECT
1479 select FB_CFB_COPYAREA
1480 select FB_CFB_IMAGEBLIT
1481 select FB_SOFT_CURSOR
1482 help
1483 Support for S1D13XXX framebuffer device family (currently only
1484 working with S1D13806). Product specs at
1485 <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
1486
1487config FB_VIRTUAL
1488 tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
1489 depends on FB
1490 select FB_CFB_FILLRECT
1491 select FB_CFB_COPYAREA
1492 select FB_CFB_IMAGEBLIT
1493 select FB_SOFT_CURSOR
1494 ---help---
1495 This is a `virtual' frame buffer device. It operates on a chunk of
1496 unswappable kernel memory instead of on the memory of a graphics
1497 board. This means you cannot see any output sent to this frame
1498 buffer device, while it does consume precious memory. The main use
1499 of this frame buffer device is testing and debugging the frame
1500 buffer subsystem. Do NOT enable it for normal systems! To protect
1501 the innocent, it has to be enabled explicitly at boot time using the
1502 kernel option `video=vfb:'.
1503
1504 To compile this driver as a module, choose M here: the
1505 module will be called vfb.
1506
1507 If unsure, say N.
1508if VT
1509 source "drivers/video/console/Kconfig"
1510endif
1511
1512if FB || SGI_NEWPORT_CONSOLE
1513 source "drivers/video/logo/Kconfig"
1514endif
1515
1516if FB && SYSFS
1517 source "drivers/video/backlight/Kconfig"
1518endif
1519
1520endmenu
1521