Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | February 2003 Kernel Parameters v2.5.59 |
| 2 | ~~~~~~~~~~~~~~~~~ |
| 3 | |
| 4 | The following is a consolidated list of the kernel parameters as implemented |
| 5 | (mostly) by the __setup() macro and sorted into English Dictionary order |
| 6 | (defined as ignoring all punctuation and sorting digits before letters in a |
| 7 | case insensitive manner), and with descriptions where known. |
| 8 | |
| 9 | Module parameters for loadable modules are specified only as the |
| 10 | parameter name with optional '=' and value as appropriate, such as: |
| 11 | |
| 12 | modprobe usbcore blinkenlights=1 |
| 13 | |
| 14 | Module parameters for modules that are built into the kernel image |
| 15 | are specified on the kernel command line with the module name plus |
| 16 | '.' plus parameter name, with '=' and value if appropriate, such as: |
| 17 | |
| 18 | usbcore.blinkenlights=1 |
| 19 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 20 | The text in square brackets at the beginning of the description states the |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 21 | restrictions on the kernel for the said kernel parameter to be valid. The |
| 22 | restrictions referred to are that the relevant option is valid if: |
| 23 | |
| 24 | ACPI ACPI support is enabled. |
| 25 | ALSA ALSA sound support is enabled. |
| 26 | APIC APIC support is enabled. |
| 27 | APM Advanced Power Management support is enabled. |
| 28 | AX25 Appropriate AX.25 support is enabled. |
| 29 | CD Appropriate CD support is enabled. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 30 | DEVFS devfs support is enabled. |
| 31 | DRM Direct Rendering Management support is enabled. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 32 | EDD BIOS Enhanced Disk Drive Services (EDD) is enabled |
| 33 | EFI EFI Partitioning (GPT) is enabled |
| 34 | EIDE EIDE/ATAPI support is enabled. |
| 35 | FB The frame buffer device is enabled. |
| 36 | HW Appropriate hardware is enabled. |
| 37 | IA-32 IA-32 aka i386 architecture is enabled. |
| 38 | IA-64 IA-64 architecture is enabled. |
| 39 | IOSCHED More than one I/O scheduler is enabled. |
Adrian Bunk | 41e2e8b | 2005-07-12 13:58:33 -0700 | [diff] [blame] | 40 | IP_PNP IP DHCP, BOOTP, or RARP is enabled. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 41 | ISAPNP ISA PnP code is enabled. |
| 42 | ISDN Appropriate ISDN support is enabled. |
| 43 | JOY Appropriate joystick support is enabled. |
| 44 | LP Printer support is enabled. |
| 45 | LOOP Loopback device support is enabled. |
| 46 | M68k M68k architecture is enabled. |
| 47 | These options have more detailed description inside of |
| 48 | Documentation/m68k/kernel-options.txt. |
| 49 | MCA MCA bus support is enabled. |
| 50 | MDA MDA console support is enabled. |
| 51 | MOUSE Appropriate mouse support is enabled. |
| 52 | MTD MTD support is enabled. |
| 53 | NET Appropriate network support is enabled. |
| 54 | NUMA NUMA support is enabled. |
| 55 | NFS Appropriate NFS support is enabled. |
| 56 | OSS OSS sound support is enabled. |
| 57 | PARIDE The ParIDE subsystem is enabled. |
| 58 | PARISC The PA-RISC architecture is enabled. |
| 59 | PCI PCI bus support is enabled. |
| 60 | PCMCIA The PCMCIA subsystem is enabled. |
| 61 | PNP Plug & Play support is enabled. |
| 62 | PPC PowerPC architecture is enabled. |
| 63 | PPT Parallel port support is enabled. |
| 64 | PS2 Appropriate PS/2 support is enabled. |
| 65 | RAM RAM disk support is enabled. |
| 66 | S390 S390 architecture is enabled. |
| 67 | SCSI Appropriate SCSI support is enabled. |
| 68 | A lot of drivers has their options described inside of |
| 69 | Documentation/scsi/. |
| 70 | SELINUX SELinux support is enabled. |
| 71 | SERIAL Serial support is enabled. |
| 72 | SMP The kernel is an SMP kernel. |
| 73 | SPARC Sparc architecture is enabled. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 74 | SWSUSP Software suspend is enabled. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 75 | TS Appropriate touchscreen support is enabled. |
| 76 | USB USB support is enabled. |
| 77 | USBHID USB Human Interface Device support is enabled. |
| 78 | V4L Video For Linux support is enabled. |
| 79 | VGA The VGA console has been enabled. |
| 80 | VT Virtual terminal support is enabled. |
| 81 | WDT Watchdog support is enabled. |
| 82 | XT IBM PC/XT MFM hard disk support is enabled. |
| 83 | X86-64 X86-64 architecture is enabled. |
| 84 | More X86-64 boot options can be found in |
| 85 | Documentation/x86_64/boot-options.txt . |
| 86 | |
| 87 | In addition, the following text indicates that the option: |
| 88 | |
| 89 | BUGS= Relates to possible processor bugs on the said processor. |
| 90 | KNL Is a kernel start-up parameter. |
| 91 | BOOT Is a boot loader parameter. |
| 92 | |
| 93 | Parameters denoted with BOOT are actually interpreted by the boot |
| 94 | loader, and have no meaning to the kernel directly. |
| 95 | Do not modify the syntax of boot loader parameters without extreme |
| 96 | need or coordination with <Documentation/i386/boot.txt>. |
| 97 | |
| 98 | Note that ALL kernel parameters listed below are CASE SENSITIVE, and that |
| 99 | a trailing = on the name of any parameter states that that parameter will |
| 100 | be entered as an environment variable, whereas its absence indicates that |
| 101 | it will appear as a kernel argument readable via /proc/cmdline by programs |
| 102 | running once the system is up. |
| 103 | |
| 104 | 53c7xx= [HW,SCSI] Amiga SCSI controllers |
| 105 | See header of drivers/scsi/53c7xx.c. |
| 106 | See also Documentation/scsi/ncr53c7xx.txt. |
| 107 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 108 | acpi= [HW,ACPI] Advanced Configuration and Power Interface |
| 109 | Format: { force | off | ht | strict | noirq } |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 110 | force -- enable ACPI if default was off |
| 111 | off -- disable ACPI if default was on |
| 112 | noirq -- do not use ACPI for IRQ routing |
| 113 | ht -- run only enough ACPI to enable Hyper Threading |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 114 | strict -- Be less tolerant of platforms that are not |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 115 | strictly ACPI specification compliant. |
| 116 | |
| 117 | See also Documentation/pm.txt, pci=noacpi |
| 118 | |
| 119 | acpi_sleep= [HW,ACPI] Sleep options |
| 120 | Format: { s3_bios, s3_mode } |
| 121 | See Documentation/power/video.txt |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 122 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 123 | acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 124 | Format: { level | edge | high | low } |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 125 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 126 | acpi_irq_balance [HW,ACPI] |
| 127 | ACPI will balance active IRQs |
| 128 | default in APIC mode |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 129 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 130 | acpi_irq_nobalance [HW,ACPI] |
| 131 | ACPI will not move active IRQs (default) |
| 132 | default in PIC mode |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 133 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 134 | acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for |
| 135 | use by PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 136 | Format: <irq>,<irq>... |
| 137 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 138 | acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 139 | Format: <irq>,<irq>... |
| 140 | |
| 141 | acpi_osi= [HW,ACPI] empty param disables _OSI |
| 142 | |
| 143 | acpi_serialize [HW,ACPI] force serialization of AML methods |
| 144 | |
| 145 | acpi_skip_timer_override [HW,ACPI] |
| 146 | Recognize and ignore IRQ0/pin2 Interrupt Override. |
| 147 | For broken nForce2 BIOS resulting in XT-PIC timer. |
| 148 | |
| 149 | acpi_dbg_layer= [HW,ACPI] |
| 150 | Format: <int> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 151 | Each bit of the <int> indicates an ACPI debug layer, |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 152 | 1: enable, 0: disable. It is useful for boot time |
| 153 | debugging. After system has booted up, it can be set |
| 154 | via /proc/acpi/debug_layer. |
| 155 | |
| 156 | acpi_dbg_level= [HW,ACPI] |
| 157 | Format: <int> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 158 | Each bit of the <int> indicates an ACPI debug level, |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 159 | 1: enable, 0: disable. It is useful for boot time |
| 160 | debugging. After system has booted up, it can be set |
| 161 | via /proc/acpi/debug_level. |
| 162 | |
| 163 | acpi_fake_ecdt [HW,ACPI] Workaround failure due to BIOS lacking ECDT |
| 164 | |
Luming Yu | 30e332f | 2005-08-12 00:31:00 -0400 | [diff] [blame] | 165 | acpi_generic_hotkey [HW,ACPI] |
| 166 | Allow consolidated generic hotkey driver to |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 167 | override platform specific driver. |
Luming Yu | 30e332f | 2005-08-12 00:31:00 -0400 | [diff] [blame] | 168 | See also Documentation/acpi-hotkey.txt. |
| 169 | |
Chuck Ebbert | 66759a0 | 2005-09-12 18:49:25 +0200 | [diff] [blame] | 170 | enable_timer_pin_1 [i386,x86-64] |
| 171 | Enable PIN 1 of APIC timer |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 172 | Can be useful to work around chipset bugs |
| 173 | (in particular on some ATI chipsets). |
Chuck Ebbert | 66759a0 | 2005-09-12 18:49:25 +0200 | [diff] [blame] | 174 | The kernel tries to set a reasonable default. |
| 175 | |
| 176 | disable_timer_pin_1 [i386,x86-64] |
| 177 | Disable PIN 1 of APIC timer |
| 178 | Can be useful to work around chipset bugs. |
| 179 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 180 | ad1816= [HW,OSS] |
| 181 | Format: <io>,<irq>,<dma>,<dma2> |
| 182 | See also Documentation/sound/oss/AD1816. |
| 183 | |
| 184 | ad1848= [HW,OSS] |
| 185 | Format: <io>,<irq>,<dma>,<dma2>,<type> |
| 186 | |
| 187 | adlib= [HW,OSS] |
| 188 | Format: <io> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 189 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 190 | advansys= [HW,SCSI] |
| 191 | See header of drivers/scsi/advansys.c. |
| 192 | |
| 193 | advwdt= [HW,WDT] Advantech WDT |
| 194 | Format: <iostart>,<iostop> |
| 195 | |
| 196 | aedsp16= [HW,OSS] Audio Excel DSP 16 |
| 197 | Format: <io>,<irq>,<dma>,<mss_io>,<mpu_io>,<mpu_irq> |
| 198 | See also header of sound/oss/aedsp16.c. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 199 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 200 | aha152x= [HW,SCSI] |
| 201 | See Documentation/scsi/aha152x.txt. |
| 202 | |
| 203 | aha1542= [HW,SCSI] |
| 204 | Format: <portbase>[,<buson>,<busoff>[,<dmaspeed>]] |
| 205 | |
| 206 | aic7xxx= [HW,SCSI] |
| 207 | See Documentation/scsi/aic7xxx.txt. |
| 208 | |
| 209 | aic79xx= [HW,SCSI] |
| 210 | See Documentation/scsi/aic79xx.txt. |
| 211 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 212 | amijoy.map= [HW,JOY] Amiga joystick support |
| 213 | Map of devices attached to JOY0DAT and JOY1DAT |
| 214 | Format: <a>,<b> |
| 215 | See also Documentation/kernel/input/joystick.txt |
| 216 | |
| 217 | analog.map= [HW,JOY] Analog joystick and gamepad support |
| 218 | Specifies type or capabilities of an analog joystick |
| 219 | connected to one of 16 gameports |
| 220 | Format: <type1>,<type2>,..<type16> |
| 221 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 222 | apc= [HW,SPARC] |
| 223 | Power management functions (SPARCstation-4/5 + deriv.) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 224 | Format: noidle |
| 225 | Disable APC CPU standby support. SPARCstation-Fox does |
| 226 | not play well with APC CPU idle - disable it if you have |
| 227 | APC and your system crashes randomly. |
| 228 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 229 | apic= [APIC,i386] Change the output verbosity whilst booting |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 230 | Format: { quiet (default) | verbose | debug } |
| 231 | Change the amount of debugging information output |
| 232 | when initialising the APIC and IO-APIC components. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 233 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 234 | apm= [APM] Advanced Power Management |
| 235 | See header of arch/i386/kernel/apm.c. |
| 236 | |
| 237 | applicom= [HW] |
| 238 | Format: <mem>,<irq> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 239 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 240 | arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards |
| 241 | Format: <io>,<irq>,<nodeID> |
| 242 | |
| 243 | ataflop= [HW,M68k] |
| 244 | |
| 245 | atarimouse= [HW,MOUSE] Atari Mouse |
| 246 | |
| 247 | atascsi= [HW,SCSI] Atari SCSI |
| 248 | |
| 249 | atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess, |
| 250 | EzKey and similar keyboards |
| 251 | |
| 252 | atkbd.reset= [HW] Reset keyboard during initialization |
| 253 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 254 | atkbd.set= [HW] Select keyboard code set |
| 255 | Format: <int> (2 = AT (default), 3 = PS/2) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 256 | |
| 257 | atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar |
| 258 | keyboards |
| 259 | |
| 260 | atkbd.softraw= [HW] Choose between synthetic and real raw mode |
| 261 | Format: <bool> (0 = real, 1 = synthetic (default)) |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 262 | |
| 263 | atkbd.softrepeat= [HW] |
| 264 | Use software keyboard repeat |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 265 | |
| 266 | autotest [IA64] |
| 267 | |
| 268 | awe= [HW,OSS] AWE32/SB32/AWE64 wave table synth |
| 269 | Format: <io>,<memsize>,<isapnp> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 270 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 271 | aztcd= [HW,CD] Aztech CD268 CDROM driver |
| 272 | Format: <io>,0x79 (?) |
| 273 | |
| 274 | baycom_epp= [HW,AX25] |
| 275 | Format: <io>,<mode> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 276 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 277 | baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem |
| 278 | Format: <io>,<mode> |
| 279 | See header of drivers/net/hamradio/baycom_par.c. |
| 280 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 281 | baycom_ser_fdx= [HW,AX25] |
| 282 | BayCom Serial Port AX.25 Modem (Full Duplex Mode) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 283 | Format: <io>,<irq>,<mode>[,<baud>] |
| 284 | See header of drivers/net/hamradio/baycom_ser_fdx.c. |
| 285 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 286 | baycom_ser_hdx= [HW,AX25] |
| 287 | BayCom Serial Port AX.25 Modem (Half Duplex Mode) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 288 | Format: <io>,<irq>,<mode> |
| 289 | See header of drivers/net/hamradio/baycom_ser_hdx.c. |
| 290 | |
| 291 | blkmtd_device= [HW,MTD] |
| 292 | blkmtd_erasesz= |
| 293 | blkmtd_ro= |
| 294 | blkmtd_bs= |
| 295 | blkmtd_count= |
| 296 | |
| 297 | bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards) |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 298 | bttv.radio= Most important insmod options are available as |
| 299 | kernel args too. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 300 | bttv.pll= See Documentation/video4linux/bttv/Insmod-options |
| 301 | bttv.tuner= and Documentation/video4linux/bttv/CARDLIST |
| 302 | |
| 303 | BusLogic= [HW,SCSI] |
| 304 | See drivers/scsi/BusLogic.c, comment before function |
| 305 | BusLogic_ParseDriverOptions(). |
| 306 | |
| 307 | c101= [NET] Moxa C101 synchronous serial card |
| 308 | |
| 309 | cachesize= [BUGS=IA-32] Override level 2 CPU cache size detection. |
| 310 | Sometimes CPU hardware bugs make them report the cache |
| 311 | size incorrectly. The kernel will attempt work arounds |
| 312 | to fix known problems, but for some CPUs it is not |
| 313 | possible to determine what the correct size should be. |
| 314 | This option provides an override for these situations. |
| 315 | |
| 316 | cdu31a= [HW,CD] |
| 317 | Format: <io>,<irq>[,PAS] |
| 318 | See header of drivers/cdrom/cdu31a.c. |
| 319 | |
| 320 | chandev= [HW,NET] Generic channel device initialisation |
| 321 | |
| 322 | checkreqprot [SELINUX] Set initial checkreqprot flag value. |
| 323 | Format: { "0" | "1" } |
| 324 | See security/selinux/Kconfig help text. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 325 | 0 -- check protection applied by kernel (includes |
| 326 | any implied execute protection). |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 327 | 1 -- check protection requested by application. |
| 328 | Default value is set via a kernel config option. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 329 | Value can be changed at runtime via |
| 330 | /selinux/checkreqprot. |
| 331 | |
| 332 | clock= [BUGS=IA-32,HW] gettimeofday timesource override. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 333 | Forces specified timesource (if avaliable) to be used |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 334 | when calculating gettimeofday(). If specicified |
| 335 | timesource is not avalible, it defaults to PIT. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 336 | Format: { pit | tsc | cyclone | pmtmr } |
| 337 | |
| 338 | hpet= [IA-32,HPET] option to disable HPET and use PIT. |
| 339 | Format: disable |
| 340 | |
| 341 | cm206= [HW,CD] |
| 342 | Format: { auto | [<io>,][<irq>] } |
| 343 | |
| 344 | com20020= [HW,NET] ARCnet - COM20020 chipset |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 345 | Format: |
| 346 | <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 347 | |
| 348 | com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers) |
| 349 | Format: <io>[,<irq>] |
| 350 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 351 | com90xx= [HW,NET] |
| 352 | ARCnet - COM90xx chipset (memory-mapped buffers) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 353 | Format: <io>[,<irq>[,<memstart>]] |
| 354 | |
| 355 | condev= [HW,S390] console device |
| 356 | conmode= |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 357 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 358 | console= [KNL] Output console device and options. |
| 359 | |
| 360 | tty<n> Use the virtual console device <n>. |
| 361 | |
| 362 | ttyS<n>[,options] |
| 363 | Use the specified serial port. The options are of |
| 364 | the form "bbbbpn", where "bbbb" is the baud rate, |
| 365 | "p" is parity ("n", "o", or "e"), and "n" is bits. |
| 366 | Default is "9600n8". |
| 367 | |
| 368 | See also Documentation/serial-console.txt. |
| 369 | |
| 370 | uart,io,<addr>[,options] |
| 371 | uart,mmio,<addr>[,options] |
| 372 | Start an early, polled-mode console on the 8250/16550 |
| 373 | UART at the specified I/O port or MMIO address, |
| 374 | switching to the matching ttyS device later. The |
| 375 | options are the same as for ttyS, above. |
| 376 | |
| 377 | cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 378 | Format: |
| 379 | <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 380 | |
| 381 | cpia_pp= [HW,PPT] |
| 382 | Format: { parport<nr> | auto | none } |
| 383 | |
Eric W. Biederman | dc009d9 | 2005-06-25 14:57:52 -0700 | [diff] [blame] | 384 | crashkernel=nn[KMG]@ss[KMG] |
| 385 | [KNL] Reserve a chunk of physical memory to |
| 386 | hold a kernel to switch to with kexec on panic. |
| 387 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 388 | cs4232= [HW,OSS] |
| 389 | Format: <io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq> |
| 390 | |
| 391 | cs89x0_dma= [HW,NET] |
| 392 | Format: <dma> |
| 393 | |
| 394 | cs89x0_media= [HW,NET] |
| 395 | Format: { rj45 | aui | bnc } |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 396 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 397 | cyclades= [HW,SERIAL] Cyclades multi-serial port adapter. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 398 | |
| 399 | dasd= [HW,NET] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 400 | See header of drivers/s390/block/dasd_devmap.c. |
| 401 | |
| 402 | db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port |
| 403 | (one device per port) |
| 404 | Format: <port#>,<type> |
| 405 | See also Documentation/input/joystick-parport.txt |
| 406 | |
| 407 | debug [KNL] Enable kernel debugging (events log level). |
| 408 | |
| 409 | decnet= [HW,NET] |
| 410 | Format: <area>[,<node>] |
| 411 | See also Documentation/networking/decnet.txt. |
| 412 | |
| 413 | devfs= [DEVFS] |
| 414 | See Documentation/filesystems/devfs/boot-options. |
| 415 | |
| 416 | dhash_entries= [KNL] |
| 417 | Set number of hash buckets for dentry cache. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 418 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 419 | digi= [HW,SERIAL] |
| 420 | IO parameters + enable/disable command. |
| 421 | |
| 422 | digiepca= [HW,SERIAL] |
| 423 | See drivers/char/README.epca and |
| 424 | Documentation/digiepca.txt. |
| 425 | |
| 426 | dmascc= [HW,AX25,SERIAL] AX.25 Z80SCC driver with DMA |
| 427 | support available. |
| 428 | Format: <io_dev0>[,<io_dev1>[,..<io_dev32>]] |
| 429 | |
| 430 | dmasound= [HW,OSS] Sound subsystem buffers |
| 431 | |
| 432 | dscc4.setup= [NET] |
| 433 | |
| 434 | dtc3181e= [HW,SCSI] |
| 435 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 436 | earlyprintk= [IA-32,X86-64] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 437 | earlyprintk=vga |
| 438 | earlyprintk=serial[,ttySn[,baudrate]] |
| 439 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 440 | Append ",keep" to not disable it when the real console |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 441 | takes over. |
| 442 | |
| 443 | Only vga or serial at a time, not both. |
| 444 | |
| 445 | Currently only ttyS0 and ttyS1 are supported. |
| 446 | |
| 447 | Interaction with the standard serial driver is not |
| 448 | very good. |
| 449 | |
| 450 | The VGA output is eventually overwritten by the real |
| 451 | console. |
| 452 | |
| 453 | eata= [HW,SCSI] |
| 454 | |
| 455 | eda= [HW,PS2] |
| 456 | |
| 457 | edb= [HW,PS2] |
| 458 | |
| 459 | edd= [EDD] |
| 460 | Format: {"of[f]" | "sk[ipmbr]"} |
| 461 | See comment in arch/i386/boot/edd.S |
| 462 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 463 | eicon= [HW,ISDN] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 464 | Format: <id>,<membase>,<irq> |
| 465 | |
| 466 | eisa_irq_edge= [PARISC,HW] |
| 467 | See header of drivers/parisc/eisa.c. |
| 468 | |
| 469 | elanfreq= [IA-32] |
| 470 | See comment before function elanfreq_setup() in |
| 471 | arch/i386/kernel/cpu/cpufreq/elanfreq.c. |
| 472 | |
| 473 | elevator= [IOSCHED] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 474 | Format: {"as" | "cfq" | "deadline" | "noop"} |
| 475 | See Documentation/block/as-iosched.txt and |
| 476 | Documentation/block/deadline-iosched.txt for details. |
| 477 | |
Vivek Goyal | 2030eae | 2005-06-25 14:58:20 -0700 | [diff] [blame] | 478 | elfcorehdr= [IA-32] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 479 | Specifies physical address of start of kernel core |
| 480 | image elf header. |
Vivek Goyal | 2030eae | 2005-06-25 14:58:20 -0700 | [diff] [blame] | 481 | See Documentation/kdump.txt for details. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 482 | |
| 483 | enforcing [SELINUX] Set initial enforcing status. |
| 484 | Format: {"0" | "1"} |
| 485 | See security/selinux/Kconfig help text. |
| 486 | 0 -- permissive (log only, no denials). |
| 487 | 1 -- enforcing (deny and log). |
| 488 | Default value is 0. |
| 489 | Value can be changed at runtime via /selinux/enforce. |
| 490 | |
| 491 | es1370= [HW,OSS] |
| 492 | Format: <lineout>[,<micbias>] |
| 493 | See also header of sound/oss/es1370.c. |
| 494 | |
| 495 | es1371= [HW,OSS] |
| 496 | Format: <spdif>,[<nomix>,[<amplifier>]] |
| 497 | See also header of sound/oss/es1371.c. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 498 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 499 | ether= [HW,NET] Ethernet cards parameters |
| 500 | This option is obsoleted by the "netdev=" option, which |
| 501 | has equivalent usage. See its documentation for details. |
| 502 | |
| 503 | eurwdt= [HW,WDT] Eurotech CPU-1220/1410 onboard watchdog. |
| 504 | Format: <io>[,<irq>] |
| 505 | |
| 506 | fd_mcs= [HW,SCSI] |
| 507 | See header of drivers/scsi/fd_mcs.c. |
| 508 | |
| 509 | fdomain= [HW,SCSI] |
| 510 | See header of drivers/scsi/fdomain.c. |
| 511 | |
| 512 | floppy= [HW] |
| 513 | See Documentation/floppy.txt. |
| 514 | |
| 515 | ftape= [HW] Floppy Tape subsystem debugging options. |
| 516 | See Documentation/ftape.txt. |
| 517 | |
| 518 | gamecon.map[2|3]= |
| 519 | [HW,JOY] Multisystem joystick and NES/SNES/PSX pad |
| 520 | support via parallel port (up to 5 devices per port) |
| 521 | Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5> |
| 522 | See also Documentation/input/joystick-parport.txt |
| 523 | |
| 524 | gamma= [HW,DRM] |
| 525 | |
| 526 | gdth= [HW,SCSI] |
| 527 | See header of drivers/scsi/gdth.c. |
| 528 | |
| 529 | gpt [EFI] Forces disk with valid GPT signature but |
| 530 | invalid Protective MBR to be treated as GPT. |
| 531 | |
| 532 | gscd= [HW,CD] |
| 533 | Format: <io> |
| 534 | |
| 535 | gt96100eth= [NET] MIPS GT96100 Advanced Communication Controller |
| 536 | |
| 537 | gus= [HW,OSS] |
| 538 | Format: <io>,<irq>,<dma>,<dma16> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 539 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 540 | gvp11= [HW,SCSI] |
| 541 | |
| 542 | hashdist= [KNL,NUMA] Large hashes allocated during boot |
| 543 | are distributed across NUMA nodes. Defaults on |
| 544 | for IA-64, off otherwise. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 545 | Format: 0 | 1 (for off | on) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 546 | |
| 547 | hcl= [IA-64] SGI's Hardware Graph compatibility layer |
| 548 | |
| 549 | hd= [EIDE] (E)IDE hard drive subsystem geometry |
| 550 | Format: <cyl>,<head>,<sect> |
| 551 | |
| 552 | hd?= [HW] (E)IDE subsystem |
| 553 | hd?lun= See Documentation/ide.txt. |
| 554 | |
| 555 | highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact |
| 556 | size of <nn>. This works even on boxes that have no |
| 557 | highmem otherwise. This also works to reduce highmem |
| 558 | size on bigger boxes. |
| 559 | |
| 560 | hisax= [HW,ISDN] |
| 561 | See Documentation/isdn/README.HiSax. |
| 562 | |
| 563 | hugepages= [HW,IA-32,IA-64] Maximal number of HugeTLB pages. |
| 564 | |
| 565 | noirqbalance [IA-32,SMP,KNL] Disable kernel irq balancing |
| 566 | |
| 567 | i8042.direct [HW] Put keyboard port into non-translated mode |
| 568 | i8042.dumbkbd [HW] Pretend that controlled can only read data from |
| 569 | keyboard and can not control its state |
| 570 | (Don't attempt to blink the leds) |
| 571 | i8042.noaux [HW] Don't check for auxiliary (== mouse) port |
Dmitry Torokhov | 945ef0d | 2005-09-04 01:42:00 -0500 | [diff] [blame] | 572 | i8042.nokbd [HW] Don't check/create keyboard port |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 573 | i8042.nomux [HW] Don't check presence of an active multiplexing |
| 574 | controller |
| 575 | i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX |
| 576 | controllers |
| 577 | i8042.panicblink= |
| 578 | [HW] Frequency with which keyboard LEDs should blink |
| 579 | when kernel panics (default is 0.5 sec) |
| 580 | i8042.reset [HW] Reset the controller during init and cleanup |
| 581 | i8042.unlock [HW] Unlock (ignore) the keylock |
| 582 | |
| 583 | i810= [HW,DRM] |
| 584 | |
Dmitry Torokhov | e70c9d5 | 2005-06-25 14:54:25 -0700 | [diff] [blame] | 585 | i8k.ignore_dmi [HW] Continue probing hardware even if DMI data |
| 586 | indicates that the driver is running on unsupported |
| 587 | hardware. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 588 | i8k.force [HW] Activate i8k driver even if SMM BIOS signature |
| 589 | does not match list of supported models. |
| 590 | i8k.power_status |
| 591 | [HW] Report power status in /proc/i8k |
| 592 | (disabled by default) |
| 593 | i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN |
| 594 | capability is set. |
| 595 | |
| 596 | ibmmcascsi= [HW,MCA,SCSI] IBM MicroChannel SCSI adapter |
| 597 | See Documentation/mca.txt. |
| 598 | |
| 599 | icn= [HW,ISDN] |
| 600 | Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]] |
| 601 | |
| 602 | ide= [HW] (E)IDE subsystem |
| 603 | Format: ide=nodma or ide=doubler or ide=reverse |
| 604 | See Documentation/ide.txt. |
| 605 | |
| 606 | ide?= [HW] (E)IDE subsystem |
| 607 | Format: ide?=noprobe or chipset specific parameters. |
| 608 | See Documentation/ide.txt. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 609 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 610 | idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed |
| 611 | See Documentation/ide.txt. |
| 612 | |
| 613 | idle= [HW] |
| 614 | Format: idle=poll or idle=halt |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 615 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 616 | ihash_entries= [KNL] |
| 617 | Set number of hash buckets for inode cache. |
| 618 | |
| 619 | in2000= [HW,SCSI] |
| 620 | See header of drivers/scsi/in2000.c. |
| 621 | |
| 622 | init= [KNL] |
| 623 | Format: <full_path> |
| 624 | Run specified binary instead of /sbin/init as init |
| 625 | process. |
| 626 | |
| 627 | initcall_debug [KNL] Trace initcalls as they are executed. Useful |
| 628 | for working out where the kernel is dying during |
| 629 | startup. |
| 630 | |
| 631 | initrd= [BOOT] Specify the location of the initial ramdisk |
| 632 | |
| 633 | inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver |
| 634 | Format: <irq> |
| 635 | |
Jesse Barnes | 2bd0fa3 | 2005-12-13 03:05:03 -0500 | [diff] [blame] | 636 | combined_mode= [HW] control which driver uses IDE ports in combined |
| 637 | mode: legacy IDE driver, libata, or both |
| 638 | (in the libata case, libata.atapi_enabled=1 may be |
| 639 | useful as well). Note that using the ide or libata |
| 640 | options may affect your device naming (e.g. by |
| 641 | changing hdc to sdb). |
| 642 | Format: combined (default), ide, or libata |
| 643 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 644 | inttest= [IA64] |
| 645 | |
| 646 | io7= [HW] IO7 for Marvel based alpha systems |
| 647 | See comment before marvel_specify_io7 in |
| 648 | arch/alpha/kernel/core_marvel.c. |
| 649 | |
| 650 | ip= [IP_PNP] |
| 651 | See Documentation/nfsroot.txt. |
| 652 | |
| 653 | ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards |
| 654 | See comment before ip2_setup() in drivers/char/ip2.c. |
| 655 | |
| 656 | ips= [HW,SCSI] Adaptec / IBM ServeRAID controller |
| 657 | See header of drivers/scsi/ips.c. |
| 658 | |
Alan Cox | 200803d | 2005-06-28 20:45:18 -0700 | [diff] [blame] | 659 | irqfixup [HW] |
| 660 | When an interrupt is not handled search all handlers |
| 661 | for it. Intended to get systems with badly broken |
| 662 | firmware running. |
| 663 | |
| 664 | irqpoll [HW] |
| 665 | When an interrupt is not handled search all handlers |
| 666 | for it. Also check all handlers each timer |
| 667 | interrupt. Intended to get systems with badly broken |
| 668 | firmware running. |
| 669 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 670 | isapnp= [ISAPNP] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 671 | Format: <RDP>,<reset>,<pci_scan>,<verbosity> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 672 | |
| 673 | isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler. |
| 674 | Format: <cpu number>,...,<cpu number> |
| 675 | This option can be used to specify one or more CPUs |
| 676 | to isolate from the general SMP balancing and scheduling |
| 677 | algorithms. The only way to move a process onto or off |
| 678 | an "isolated" CPU is via the CPU affinity syscalls. |
| 679 | <cpu number> begins at 0 and the maximum value is |
| 680 | "number of CPUs in system - 1". |
| 681 | |
| 682 | This option is the preferred way to isolate CPUs. The |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 683 | alternative -- manually setting the CPU mask of all |
| 684 | tasks in the system -- can cause problems and |
| 685 | suboptimal load balancer performance. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 686 | |
| 687 | isp16= [HW,CD] |
| 688 | Format: <io>,<irq>,<dma>,<setup> |
| 689 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 690 | iucv= [HW,NET] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 691 | |
| 692 | js= [HW,JOY] Analog joystick |
| 693 | See Documentation/input/joystick.txt. |
| 694 | |
| 695 | keepinitrd [HW,ARM] |
| 696 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 697 | kstack=N [IA-32,X86-64] Print N words from the kernel stack |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 698 | in oops dumps. |
| 699 | |
| 700 | l2cr= [PPC] |
| 701 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 702 | lapic [IA-32,APIC] Enable the local APIC even if BIOS |
| 703 | disabled it. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 704 | |
| 705 | lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip |
| 706 | Format: addr:<io>,irq:<irq> |
| 707 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 708 | llsc*= [IA64] See function print_params() in |
| 709 | arch/ia64/sn/kernel/llsc4.c. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 710 | |
| 711 | load_ramdisk= [RAM] List of ramdisks to load from floppy |
| 712 | See Documentation/ramdisk.txt. |
| 713 | |
| 714 | lockd.udpport= [NFS] |
| 715 | |
| 716 | lockd.tcpport= [NFS] |
| 717 | |
| 718 | logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver |
| 719 | Format: <irq> |
| 720 | |
| 721 | loglevel= All Kernel Messages with a loglevel smaller than the |
| 722 | console loglevel will be printed to the console. It can |
| 723 | also be changed with klogd or other programs. The |
| 724 | loglevels are defined as follows: |
| 725 | |
| 726 | 0 (KERN_EMERG) system is unusable |
| 727 | 1 (KERN_ALERT) action must be taken immediately |
| 728 | 2 (KERN_CRIT) critical conditions |
| 729 | 3 (KERN_ERR) error conditions |
| 730 | 4 (KERN_WARNING) warning conditions |
| 731 | 5 (KERN_NOTICE) normal but significant condition |
| 732 | 6 (KERN_INFO) informational |
| 733 | 7 (KERN_DEBUG) debug-level messages |
| 734 | |
| 735 | log_buf_len=n Sets the size of the printk ring buffer, in bytes. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 736 | Format: { n | nk | nM } |
| 737 | n must be a power of two. The default size |
| 738 | is set in the kernel config file. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 739 | |
| 740 | lp=0 [LP] Specify parallel ports to use, e.g, |
| 741 | lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses |
| 742 | lp=reset first parallel port). 'lp=0' disables the |
| 743 | lp=auto printer driver. 'lp=reset' (which can be |
| 744 | specified in addition to the ports) causes |
| 745 | attached printers to be reset. Using |
| 746 | lp=port1,port2,... specifies the parallel ports |
| 747 | to associate lp devices with, starting with |
| 748 | lp0. A port specification may be 'none' to skip |
| 749 | that lp device, or a parport name such as |
| 750 | 'parport0'. Specifying 'lp=auto' instead of a |
| 751 | port specification list means that device IDs |
| 752 | from each port should be examined, to see if |
| 753 | an IEEE 1284-compliant printer is attached; if |
| 754 | so, the driver will manage that printer. |
| 755 | See also header of drivers/char/lp.c. |
| 756 | |
| 757 | lpj=n [KNL] |
| 758 | Sets loops_per_jiffy to given constant, thus avoiding |
| 759 | time-consuming boot-time autodetection (up to 250 ms per |
| 760 | CPU). 0 enables autodetection (default). To determine |
| 761 | the correct value for your kernel, boot with normal |
| 762 | autodetection and see what value is printed. Note that |
| 763 | on SMP systems the preset will be applied to all CPUs, |
| 764 | which is likely to cause problems if your CPUs need |
| 765 | significantly divergent settings. An incorrect value |
| 766 | will cause delays in the kernel to be wrong, leading to |
| 767 | unpredictable I/O errors and other breakage. Although |
| 768 | unlikely, in the extreme case this might damage your |
| 769 | hardware. |
| 770 | |
| 771 | ltpc= [NET] |
| 772 | Format: <io>,<irq>,<dma> |
| 773 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 774 | mac5380= [HW,SCSI] Format: |
| 775 | <can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 776 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 777 | mac53c9x= [HW,SCSI] Format: |
| 778 | <num_esps>,<disconnect>,<nosync>,<can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 779 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 780 | machvec= [IA64] Force the use of a particular machine-vector |
| 781 | (machvec) in a generic kernel. |
| 782 | Example: machvec=hpzx1_swiotlb |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 783 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 784 | mad16= [HW,OSS] Format: |
| 785 | <io>,<irq>,<dma>,<dma16>,<mpu_io>,<mpu_irq>,<joystick> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 786 | |
| 787 | maui= [HW,OSS] |
| 788 | Format: <io>,<irq> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 789 | |
| 790 | max_loop= [LOOP] Maximum number of loopback devices that can |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 791 | be mounted |
| 792 | Format: <1-256> |
| 793 | |
| 794 | maxcpus= [SMP] Maximum number of processors that an SMP kernel |
| 795 | should make use of |
| 796 | |
Bob Picco | 2b2c375 | 2005-06-29 18:00:00 -0700 | [diff] [blame] | 797 | max_addr=[KMG] [KNL,BOOT,ia64] All physical memory greater than or |
| 798 | equal to this physical address is ignored. |
| 799 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 800 | max_luns= [SCSI] Maximum number of LUNs to probe. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 801 | Should be between 1 and 2^32-1. |
| 802 | |
| 803 | max_report_luns= |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 804 | [SCSI] Maximum number of LUNs received. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 805 | Should be between 1 and 16384. |
| 806 | |
| 807 | mca-pentium [BUGS=IA-32] |
| 808 | |
| 809 | mcatest= [IA-64] |
| 810 | |
| 811 | mcd= [HW,CD] |
| 812 | Format: <port>,<irq>,<mitsumi_bug_93_wait> |
| 813 | |
| 814 | mcdx= [HW,CD] |
| 815 | |
| 816 | mce [IA-32] Machine Check Exception |
| 817 | |
| 818 | md= [HW] RAID subsystems devices and level |
| 819 | See Documentation/md.txt. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 820 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 821 | mdacon= [MDA] |
| 822 | Format: <first>,<last> |
| 823 | Specifies range of consoles to be captured by the MDA. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 824 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 825 | mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory |
| 826 | Amount of memory to be used when the kernel is not able |
| 827 | to see the whole system memory or for test. |
| 828 | [IA-32] Use together with memmap= to avoid physical |
| 829 | address space collisions. Without memmap= PCI devices |
| 830 | could be placed at addresses belonging to unused RAM. |
| 831 | |
| 832 | mem=nopentium [BUGS=IA-32] Disable usage of 4MB pages for kernel |
| 833 | memory. |
| 834 | |
| 835 | memmap=exactmap [KNL,IA-32] Enable setting of an exact |
| 836 | E820 memory map, as specified by the user. |
| 837 | Such memmap=exactmap lines can be constructed based on |
| 838 | BIOS output or other requirements. See the memmap=nn@ss |
| 839 | option description. |
| 840 | |
| 841 | memmap=nn[KMG]@ss[KMG] |
| 842 | [KNL] Force usage of a specific region of memory |
| 843 | Region of memory to be used, from ss to ss+nn. |
| 844 | |
| 845 | memmap=nn[KMG]#ss[KMG] |
| 846 | [KNL,ACPI] Mark specific memory as ACPI data. |
| 847 | Region of memory to be used, from ss to ss+nn. |
| 848 | |
| 849 | memmap=nn[KMG]$ss[KMG] |
| 850 | [KNL,ACPI] Mark specific memory as reserved. |
| 851 | Region of memory to be used, from ss to ss+nn. |
| 852 | |
| 853 | meye.*= [HW] Set MotionEye Camera parameters |
| 854 | See Documentation/video4linux/meye.txt. |
| 855 | |
| 856 | mga= [HW,DRM] |
| 857 | |
| 858 | mousedev.tap_time= |
| 859 | [MOUSE] Maximum time between finger touching and |
| 860 | leaving touchpad surface for touch to be considered |
| 861 | a tap and be reported as a left button click (for |
| 862 | touchpads working in absolute mode only). |
| 863 | Format: <msecs> |
| 864 | mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices |
| 865 | reporting absolute coordinates, such as tablets |
| 866 | mousedev.yres= [MOUSE] Vertical screen resolution, used for devices |
| 867 | reporting absolute coordinates, such as tablets |
| 868 | |
| 869 | mpu401= [HW,OSS] |
| 870 | Format: <io>,<irq> |
| 871 | |
| 872 | MTD_Partition= [MTD] |
| 873 | Format: <name>,<region-number>,<size>,<offset> |
| 874 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 875 | MTD_Region= [MTD] Format: |
| 876 | <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 877 | |
| 878 | mtdparts= [MTD] |
| 879 | See drivers/mtd/cmdline.c. |
| 880 | |
| 881 | mtouchusb.raw_coordinates= |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 882 | [HW] Make the MicroTouch USB driver use raw coordinates |
| 883 | ('y', default) or cooked coordinates ('n') |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 884 | |
| 885 | n2= [NET] SDL Inc. RISCom/N2 synchronous serial card |
| 886 | |
| 887 | NCR_D700= [HW,SCSI] |
| 888 | See header of drivers/scsi/NCR_D700.c. |
| 889 | |
| 890 | ncr5380= [HW,SCSI] |
| 891 | |
| 892 | ncr53c400= [HW,SCSI] |
| 893 | |
| 894 | ncr53c400a= [HW,SCSI] |
| 895 | |
| 896 | ncr53c406a= [HW,SCSI] |
| 897 | |
| 898 | ncr53c8xx= [HW,SCSI] |
| 899 | |
| 900 | netdev= [NET] Network devices parameters |
| 901 | Format: <irq>,<io>,<mem_start>,<mem_end>,<name> |
| 902 | Note that mem_start is often overloaded to mean |
| 903 | something different and driver-specific. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 904 | This usage is only documented in each driver source |
| 905 | file if at all. |
| 906 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 907 | nfsaddrs= [NFS] |
| 908 | See Documentation/nfsroot.txt. |
| 909 | |
| 910 | nfsroot= [NFS] nfs root filesystem for disk-less boxes. |
| 911 | See Documentation/nfsroot.txt. |
| 912 | |
| 913 | nmi_watchdog= [KNL,BUGS=IA-32] Debugging features for SMP kernels |
| 914 | |
| 915 | no387 [BUGS=IA-32] Tells the kernel to use the 387 maths |
| 916 | emulation library even if a 387 maths coprocessor |
| 917 | is present. |
| 918 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 919 | noalign [KNL,ARM] |
| 920 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 921 | noapic [SMP,APIC] Tells the kernel to not make use of any |
| 922 | IOAPICs that may be present in the system. |
| 923 | |
| 924 | noasync [HW,M68K] Disables async and sync negotiation for |
| 925 | all devices. |
| 926 | |
| 927 | nobats [PPC] Do not use BATs for mapping kernel lowmem |
| 928 | on "Classic" PPC cores. |
| 929 | |
| 930 | nocache [ARM] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 931 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 932 | nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects. |
| 933 | |
| 934 | noexec [IA-64] |
| 935 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 936 | noexec [IA-32,X86-64] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 937 | noexec=on: enable non-executable mappings (default) |
| 938 | noexec=off: disable nn-executable mappings |
| 939 | |
| 940 | nofxsr [BUGS=IA-32] |
| 941 | |
| 942 | nohlt [BUGS=ARM] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 943 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 944 | no-hlt [BUGS=IA-32] Tells the kernel that the hlt |
| 945 | instruction doesn't work correctly and not to |
| 946 | use it. |
| 947 | |
| 948 | nohalt [IA-64] Tells the kernel not to use the power saving |
| 949 | function PAL_HALT_LIGHT when idle. This increases |
| 950 | power-consumption. On the positive side, it reduces |
| 951 | interrupt wake-up latency, which may improve performance |
| 952 | in certain environments such as networked servers or |
| 953 | real-time systems. |
| 954 | |
| 955 | noirqdebug [IA-32] Disables the code which attempts to detect and |
| 956 | disable unhandled interrupt sources. |
| 957 | |
| 958 | noisapnp [ISAPNP] Disables ISA PnP code. |
| 959 | |
| 960 | noinitrd [RAM] Tells the kernel not to load any configured |
| 961 | initial RAM disk. |
| 962 | |
| 963 | nointroute [IA-64] |
| 964 | |
| 965 | nolapic [IA-32,APIC] Do not enable or use the local APIC. |
| 966 | |
| 967 | noltlbs [PPC] Do not use large page/tlb entries for kernel |
| 968 | lowmem mapping on PPC40x. |
| 969 | |
| 970 | nomce [IA-32] Machine Check Exception |
| 971 | |
| 972 | noresidual [PPC] Don't use residual data on PReP machines. |
| 973 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 974 | noresume [SWSUSP] Disables resume and restores original swap |
| 975 | space. |
| 976 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 977 | no-scroll [VGA] Disables scrollback. |
| 978 | This is required for the Braillex ib80-piezo Braille |
| 979 | reader made by F.H. Papenmeier (Germany). |
| 980 | |
| 981 | nosbagart [IA-64] |
| 982 | |
| 983 | nosmp [SMP] Tells an SMP kernel to act as a UP kernel. |
| 984 | |
| 985 | nosync [HW,M68K] Disables sync negotiation for all devices. |
| 986 | |
| 987 | notsc [BUGS=IA-32] Disable Time Stamp Counter |
| 988 | |
| 989 | nousb [USB] Disable the USB subsystem |
| 990 | |
| 991 | nowb [ARM] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 992 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 993 | opl3= [HW,OSS] |
| 994 | Format: <io> |
| 995 | |
| 996 | opl3sa= [HW,OSS] |
| 997 | Format: <io>,<irq>,<dma>,<dma2>,<mpu_io>,<mpu_irq> |
| 998 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 999 | opl3sa2= [HW,OSS] Format: |
| 1000 | <io>,<irq>,<dma>,<dma2>,<mss_io>,<mpu_io>,<ymode>,<loopback>[,<isapnp>,<multiple] |
| 1001 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1002 | oprofile.timer= [HW] |
| 1003 | Use timer interrupt instead of performance counters |
| 1004 | |
| 1005 | optcd= [HW,CD] |
| 1006 | Format: <io> |
| 1007 | |
| 1008 | osst= [HW,SCSI] SCSI Tape Driver |
| 1009 | Format: <buffer_size>,<write_threshold> |
| 1010 | See also Documentation/scsi/st.txt. |
| 1011 | |
| 1012 | panic= [KNL] Kernel behaviour on panic |
| 1013 | Format: <timeout> |
| 1014 | |
| 1015 | parkbd.port= [HW] Parallel port number the keyboard adapter is |
| 1016 | connected to, default is 0. |
| 1017 | Format: <parport#> |
| 1018 | parkbd.mode= [HW] Parallel port keyboard adapter mode of operation, |
| 1019 | 0 for XT, 1 for AT (default is AT). |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1020 | Format: <mode> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1021 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1022 | parport= [HW,PPT] Specify parallel ports. 0 disables. |
| 1023 | Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] } |
| 1024 | Use 'auto' to force the driver to use any |
| 1025 | IRQ/DMA settings detected (the default is to |
| 1026 | ignore detected IRQ/DMA settings because of |
| 1027 | possible conflicts). You can specify the base |
| 1028 | address, IRQ, and DMA settings; IRQ and DMA |
| 1029 | should be numbers, or 'auto' (for using detected |
| 1030 | settings on that particular port), or 'nofifo' |
| 1031 | (to avoid using a FIFO even if it is detected). |
| 1032 | Parallel ports are assigned in the order they |
| 1033 | are specified on the command line, starting |
| 1034 | with parport0. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1035 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1036 | parport_init_mode= [HW,PPT] |
| 1037 | Configure VIA parallel port to operate in |
| 1038 | a specific mode. This is necessary on Pegasos |
| 1039 | computer where firmware has no options for setting |
| 1040 | up parallel port mode and sets it to spp. |
| 1041 | Currently this function knows 686a and 8231 chips. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1042 | Format: [spp|ps2|epp|ecp|ecpepp] |
| 1043 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1044 | pas2= [HW,OSS] Format: |
| 1045 | <io>,<irq>,<dma>,<dma16>,<sb_io>,<sb_irq>,<sb_dma>,<sb_dma16> |
| 1046 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1047 | pas16= [HW,SCSI] |
| 1048 | See header of drivers/scsi/pas16.c. |
| 1049 | |
| 1050 | pcbit= [HW,ISDN] |
| 1051 | |
| 1052 | pcd. [PARIDE] |
| 1053 | See header of drivers/block/paride/pcd.c. |
| 1054 | See also Documentation/paride.txt. |
| 1055 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1056 | pci=option[,option...] [PCI] various PCI subsystem options: |
| 1057 | off [IA-32] don't probe for the PCI bus |
| 1058 | bios [IA-32] force use of PCI BIOS, don't access |
| 1059 | the hardware directly. Use this if your machine |
| 1060 | has a non-standard PCI host bridge. |
| 1061 | nobios [IA-32] disallow use of PCI BIOS, only direct |
| 1062 | hardware access methods are allowed. Use this |
| 1063 | if you experience crashes upon bootup and you |
| 1064 | suspect they are caused by the BIOS. |
| 1065 | conf1 [IA-32] Force use of PCI Configuration |
| 1066 | Mechanism 1. |
| 1067 | conf2 [IA-32] Force use of PCI Configuration |
| 1068 | Mechanism 2. |
| 1069 | nosort [IA-32] Don't sort PCI devices according to |
| 1070 | order given by the PCI BIOS. This sorting is |
| 1071 | done to get a device order compatible with |
| 1072 | older kernels. |
| 1073 | biosirq [IA-32] Use PCI BIOS calls to get the interrupt |
| 1074 | routing table. These calls are known to be buggy |
| 1075 | on several machines and they hang the machine |
| 1076 | when used, but on other computers it's the only |
| 1077 | way to get the interrupt routing table. Try |
| 1078 | this option if the kernel is unable to allocate |
| 1079 | IRQs or discover secondary PCI buses on your |
| 1080 | motherboard. |
| 1081 | rom [IA-32] Assign address space to expansion ROMs. |
| 1082 | Use with caution as certain devices share |
| 1083 | address decoders between ROMs and other |
| 1084 | resources. |
| 1085 | irqmask=0xMMMM [IA-32] Set a bit mask of IRQs allowed to be |
| 1086 | assigned automatically to PCI devices. You can |
| 1087 | make the kernel exclude IRQs of your ISA cards |
| 1088 | this way. |
jayalk@intworks.biz | 120bb42 | 2005-03-21 20:20:42 -0800 | [diff] [blame] | 1089 | pirqaddr=0xAAAAA [IA-32] Specify the physical address |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1090 | of the PIRQ table (normally generated |
| 1091 | by the BIOS) if it is outside the |
| 1092 | F0000h-100000h range. |
| 1093 | lastbus=N [IA-32] Scan all buses thru bus #N. Can be |
| 1094 | useful if the kernel is unable to find your |
| 1095 | secondary buses and you want to tell it |
| 1096 | explicitly which ones they are. |
| 1097 | assign-busses [IA-32] Always assign all PCI bus |
| 1098 | numbers ourselves, overriding |
| 1099 | whatever the firmware may have done. |
| 1100 | usepirqmask [IA-32] Honor the possible IRQ mask stored |
| 1101 | in the BIOS $PIR table. This is needed on |
| 1102 | some systems with broken BIOSes, notably |
| 1103 | some HP Pavilion N5400 and Omnibook XE3 |
| 1104 | notebooks. This will have no effect if ACPI |
| 1105 | IRQ routing is enabled. |
| 1106 | noacpi [IA-32] Do not use ACPI for IRQ routing |
| 1107 | or for PCI scanning. |
| 1108 | routeirq Do IRQ routing for all PCI devices. |
| 1109 | This is normally done in pci_enable_device(), |
| 1110 | so this option is a temporary workaround |
| 1111 | for broken drivers that don't call it. |
| 1112 | firmware [ARM] Do not re-enumerate the bus but instead |
| 1113 | just use the configuration from the |
| 1114 | bootloader. This is currently used on |
| 1115 | IXP2000 systems where the bus has to be |
| 1116 | configured a certain way for adjunct CPUs. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1117 | |
| 1118 | pcmv= [HW,PCMCIA] BadgePAD 4 |
| 1119 | |
| 1120 | pd. [PARIDE] |
| 1121 | See Documentation/paride.txt. |
| 1122 | |
| 1123 | pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at |
| 1124 | boot time. |
| 1125 | Format: { 0 | 1 } |
| 1126 | See arch/parisc/kernel/pdc_chassis.c |
| 1127 | |
| 1128 | pf. [PARIDE] |
| 1129 | See Documentation/paride.txt. |
| 1130 | |
| 1131 | pg. [PARIDE] |
| 1132 | See Documentation/paride.txt. |
| 1133 | |
| 1134 | pirq= [SMP,APIC] Manual mp-table setup |
| 1135 | See Documentation/i386/IO-APIC.txt. |
| 1136 | |
| 1137 | plip= [PPT,NET] Parallel port network link |
| 1138 | Format: { parport<nr> | timid | 0 } |
| 1139 | See also Documentation/parport.txt. |
| 1140 | |
| 1141 | pnpacpi= [ACPI] |
| 1142 | { off } |
| 1143 | |
| 1144 | pnpbios= [ISAPNP] |
| 1145 | { on | off | curr | res | no-curr | no-res } |
| 1146 | |
| 1147 | pnp_reserve_irq= |
| 1148 | [ISAPNP] Exclude IRQs for the autoconfiguration |
| 1149 | |
| 1150 | pnp_reserve_dma= |
| 1151 | [ISAPNP] Exclude DMAs for the autoconfiguration |
| 1152 | |
| 1153 | pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1154 | Ranges are in pairs (I/O port base and size). |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1155 | |
| 1156 | pnp_reserve_mem= |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1157 | [ISAPNP] Exclude memory regions for the |
| 1158 | autoconfiguration. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1159 | Ranges are in pairs (memory base and size). |
| 1160 | |
| 1161 | profile= [KNL] Enable kernel profiling via /proc/profile |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1162 | Format: [schedule,]<number> |
| 1163 | Param: "schedule" - profile schedule points. |
| 1164 | Param: <number> - step/bucket size as a power of 2 for |
| 1165 | statistical time based profiling. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1166 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1167 | processor.max_cstate= [HW,ACPI] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1168 | Limit processor to maximum C-state |
| 1169 | max_cstate=9 overrides any DMI blacklist limit. |
| 1170 | |
| 1171 | prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk |
| 1172 | before loading. |
| 1173 | See Documentation/ramdisk.txt. |
| 1174 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1175 | psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to |
| 1176 | probe for; one of (bare|imps|exps|lifebook|any). |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1177 | psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports |
| 1178 | per second. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1179 | psmouse.resetafter= [HW,MOUSE] |
| 1180 | Try to reset the device after so many bad packets |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1181 | (0 = never). |
| 1182 | psmouse.resolution= |
| 1183 | [HW,MOUSE] Set desired mouse resolution, in dpi. |
| 1184 | psmouse.smartscroll= |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1185 | [HW,MOUSE] Controls Logitech smartscroll autorepeat. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1186 | 0 = disabled, 1 = enabled (default). |
| 1187 | |
| 1188 | pss= [HW,OSS] Personal Sound System (ECHO ESC614) |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1189 | Format: |
| 1190 | <io>,<mss_io>,<mss_irq>,<mss_dma>,<mpu_io>,<mpu_irq> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1191 | |
| 1192 | pt. [PARIDE] |
| 1193 | See Documentation/paride.txt. |
| 1194 | |
| 1195 | quiet= [KNL] Disable log messages |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1196 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1197 | r128= [HW,DRM] |
| 1198 | |
| 1199 | raid= [HW,RAID] |
| 1200 | See Documentation/md.txt. |
| 1201 | |
| 1202 | ramdisk= [RAM] Sizes of RAM disks in kilobytes [deprecated] |
| 1203 | See Documentation/ramdisk.txt. |
| 1204 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1205 | ramdisk_blocksize= [RAM] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1206 | See Documentation/ramdisk.txt. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1207 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1208 | ramdisk_size= [RAM] Sizes of RAM disks in kilobytes |
| 1209 | New name for the ramdisk parameter. |
| 1210 | See Documentation/ramdisk.txt. |
| 1211 | |
Olof Johansson | ffdfc40 | 2005-09-06 15:17:19 -0700 | [diff] [blame] | 1212 | rdinit= [KNL] |
| 1213 | Format: <full_path> |
| 1214 | Run specified binary instead of /init from the ramdisk, |
| 1215 | used for early userspace startup. See initrd. |
| 1216 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1217 | reboot= [BUGS=IA-32,BUGS=ARM,BUGS=IA-64] Rebooting mode |
| 1218 | Format: <reboot_mode>[,<reboot_mode2>[,...]] |
| 1219 | See arch/*/kernel/reboot.c. |
| 1220 | |
| 1221 | reserve= [KNL,BUGS] Force the kernel to ignore some iomem area |
| 1222 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1223 | resume= [SWSUSP] |
| 1224 | Specify the partition device for software suspend |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1225 | |
| 1226 | rhash_entries= [KNL,NET] |
| 1227 | Set number of hash buckets for route cache |
| 1228 | |
| 1229 | riscom8= [HW,SERIAL] |
| 1230 | Format: <io_board1>[,<io_board2>[,...<io_boardN>]] |
| 1231 | |
| 1232 | ro [KNL] Mount root device read-only on boot |
| 1233 | |
| 1234 | root= [KNL] Root filesystem |
| 1235 | |
| 1236 | rootdelay= [KNL] Delay (in seconds) to pause before attempting to |
| 1237 | mount the root filesystem |
| 1238 | |
| 1239 | rootflags= [KNL] Set root filesystem mount option string |
| 1240 | |
| 1241 | rootfstype= [KNL] Set root filesystem type |
| 1242 | |
| 1243 | rw [KNL] Mount root device read-write on boot |
| 1244 | |
| 1245 | S [KNL] Run init in single mode |
| 1246 | |
| 1247 | sa1100ir [NET] |
| 1248 | See drivers/net/irda/sa1100_ir.c. |
| 1249 | |
| 1250 | sb= [HW,OSS] |
| 1251 | Format: <io>,<irq>,<dma>,<dma2> |
| 1252 | |
| 1253 | sbni= [NET] Granch SBNI12 leased line adapter |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1254 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1255 | sbpcd= [HW,CD] Soundblaster CD adapter |
| 1256 | Format: <io>,<type> |
| 1257 | See a comment before function sbpcd_setup() in |
| 1258 | drivers/cdrom/sbpcd.c. |
| 1259 | |
| 1260 | sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver |
| 1261 | Format: <io>[,<timeout>[,<isapnp>]] |
| 1262 | |
| 1263 | scsi_debug_*= [SCSI] |
| 1264 | See drivers/scsi/scsi_debug.c. |
| 1265 | |
| 1266 | scsi_default_dev_flags= |
| 1267 | [SCSI] SCSI default device flags |
| 1268 | Format: <integer> |
| 1269 | |
| 1270 | scsi_dev_flags= [SCSI] Black/white list entry for vendor and model |
| 1271 | Format: <vendor>:<model>:<flags> |
| 1272 | (flags are integer value) |
| 1273 | |
| 1274 | scsi_logging= [SCSI] |
| 1275 | |
| 1276 | selinux [SELINUX] Disable or enable SELinux at boot time. |
| 1277 | Format: { "0" | "1" } |
| 1278 | See security/selinux/Kconfig help text. |
| 1279 | 0 -- disable. |
| 1280 | 1 -- enable. |
| 1281 | Default value is set via kernel config option. |
| 1282 | If enabled at boot time, /selinux/disable can be used |
| 1283 | later to disable prior to initial policy load. |
| 1284 | |
| 1285 | serialnumber [BUGS=IA-32] |
| 1286 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1287 | sg_def_reserved_size= [SCSI] |
| 1288 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1289 | sgalaxy= [HW,OSS] |
| 1290 | Format: <io>,<irq>,<dma>,<dma2>,<sgbase> |
| 1291 | |
| 1292 | shapers= [NET] |
| 1293 | Maximal number of shapers. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1294 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1295 | sim710= [SCSI,HW] |
| 1296 | See header of drivers/scsi/sim710.c. |
| 1297 | |
| 1298 | simeth= [IA-64] |
| 1299 | simscsi= |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1300 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1301 | sjcd= [HW,CD] |
| 1302 | Format: <io>,<irq>,<dma> |
| 1303 | See header of drivers/cdrom/sjcd.c. |
| 1304 | |
| 1305 | slram= [HW,MTD] |
| 1306 | |
| 1307 | smart2= [HW] |
| 1308 | Format: <io1>[,<io2>[,...,<io8>]] |
| 1309 | |
| 1310 | snd-ad1816a= [HW,ALSA] |
| 1311 | |
| 1312 | snd-ad1848= [HW,ALSA] |
| 1313 | |
| 1314 | snd-ali5451= [HW,ALSA] |
| 1315 | |
| 1316 | snd-als100= [HW,ALSA] |
| 1317 | |
| 1318 | snd-als4000= [HW,ALSA] |
| 1319 | |
| 1320 | snd-azt2320= [HW,ALSA] |
| 1321 | |
| 1322 | snd-cmi8330= [HW,ALSA] |
| 1323 | |
| 1324 | snd-cmipci= [HW,ALSA] |
| 1325 | |
| 1326 | snd-cs4231= [HW,ALSA] |
| 1327 | |
| 1328 | snd-cs4232= [HW,ALSA] |
| 1329 | |
| 1330 | snd-cs4236= [HW,ALSA] |
| 1331 | |
| 1332 | snd-cs4281= [HW,ALSA] |
| 1333 | |
| 1334 | snd-cs46xx= [HW,ALSA] |
| 1335 | |
| 1336 | snd-dt019x= [HW,ALSA] |
| 1337 | |
| 1338 | snd-dummy= [HW,ALSA] |
| 1339 | |
| 1340 | snd-emu10k1= [HW,ALSA] |
| 1341 | |
| 1342 | snd-ens1370= [HW,ALSA] |
| 1343 | |
| 1344 | snd-ens1371= [HW,ALSA] |
| 1345 | |
| 1346 | snd-es968= [HW,ALSA] |
| 1347 | |
| 1348 | snd-es1688= [HW,ALSA] |
| 1349 | |
| 1350 | snd-es18xx= [HW,ALSA] |
| 1351 | |
| 1352 | snd-es1938= [HW,ALSA] |
| 1353 | |
| 1354 | snd-es1968= [HW,ALSA] |
| 1355 | |
| 1356 | snd-fm801= [HW,ALSA] |
| 1357 | |
| 1358 | snd-gusclassic= [HW,ALSA] |
| 1359 | |
| 1360 | snd-gusextreme= [HW,ALSA] |
| 1361 | |
| 1362 | snd-gusmax= [HW,ALSA] |
| 1363 | |
| 1364 | snd-hdsp= [HW,ALSA] |
| 1365 | |
| 1366 | snd-ice1712= [HW,ALSA] |
| 1367 | |
| 1368 | snd-intel8x0= [HW,ALSA] |
| 1369 | |
| 1370 | snd-interwave= [HW,ALSA] |
| 1371 | |
| 1372 | snd-interwave-stb= |
| 1373 | [HW,ALSA] |
| 1374 | |
| 1375 | snd-korg1212= [HW,ALSA] |
| 1376 | |
| 1377 | snd-maestro3= [HW,ALSA] |
| 1378 | |
| 1379 | snd-mpu401= [HW,ALSA] |
| 1380 | |
| 1381 | snd-mtpav= [HW,ALSA] |
| 1382 | |
| 1383 | snd-nm256= [HW,ALSA] |
| 1384 | |
| 1385 | snd-opl3sa2= [HW,ALSA] |
| 1386 | |
| 1387 | snd-opti92x-ad1848= |
| 1388 | [HW,ALSA] |
| 1389 | |
| 1390 | snd-opti92x-cs4231= |
| 1391 | [HW,ALSA] |
| 1392 | |
| 1393 | snd-opti93x= [HW,ALSA] |
| 1394 | |
| 1395 | snd-pmac= [HW,ALSA] |
| 1396 | |
| 1397 | snd-rme32= [HW,ALSA] |
| 1398 | |
| 1399 | snd-rme96= [HW,ALSA] |
| 1400 | |
| 1401 | snd-rme9652= [HW,ALSA] |
| 1402 | |
| 1403 | snd-sb8= [HW,ALSA] |
| 1404 | |
| 1405 | snd-sb16= [HW,ALSA] |
| 1406 | |
| 1407 | snd-sbawe= [HW,ALSA] |
| 1408 | |
| 1409 | snd-serial= [HW,ALSA] |
| 1410 | |
| 1411 | snd-sgalaxy= [HW,ALSA] |
| 1412 | |
| 1413 | snd-sonicvibes= [HW,ALSA] |
| 1414 | |
| 1415 | snd-sun-amd7930= |
| 1416 | [HW,ALSA] |
| 1417 | |
| 1418 | snd-sun-cs4231= [HW,ALSA] |
| 1419 | |
| 1420 | snd-trident= [HW,ALSA] |
| 1421 | |
| 1422 | snd-usb-audio= [HW,ALSA,USB] |
| 1423 | |
| 1424 | snd-via82xx= [HW,ALSA] |
| 1425 | |
| 1426 | snd-virmidi= [HW,ALSA] |
| 1427 | |
| 1428 | snd-wavefront= [HW,ALSA] |
| 1429 | |
| 1430 | snd-ymfpci= [HW,ALSA] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1431 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1432 | sonicvibes= [HW,OSS] |
| 1433 | Format: <reverb> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1434 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1435 | sonycd535= [HW,CD] |
| 1436 | Format: <io>[,<irq>] |
| 1437 | |
| 1438 | sonypi.*= [HW] Sony Programmable I/O Control Device driver |
| 1439 | See Documentation/sonypi.txt |
| 1440 | |
| 1441 | specialix= [HW,SERIAL] Specialix multi-serial port adapter |
| 1442 | See Documentation/specialix.txt. |
| 1443 | |
| 1444 | spia_io_base= [HW,MTD] |
| 1445 | spia_fio_base= |
| 1446 | spia_pedr= |
| 1447 | spia_peddr= |
| 1448 | |
| 1449 | sscape= [HW,OSS] |
| 1450 | Format: <io>,<irq>,<dma>,<mpu_io>,<mpu_irq> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1451 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1452 | st= [HW,SCSI] SCSI tape parameters (buffers, etc.) |
| 1453 | See Documentation/scsi/st.txt. |
| 1454 | |
| 1455 | st0x= [HW,SCSI] |
| 1456 | See header of drivers/scsi/seagate.c. |
| 1457 | |
| 1458 | sti= [PARISC,HW] |
| 1459 | Format: <num> |
| 1460 | Set the STI (builtin display/keyboard on the HP-PARISC |
| 1461 | machines) console (graphic card) which should be used |
| 1462 | as the initial boot-console. |
| 1463 | See also comment in drivers/video/console/sticore.c. |
| 1464 | |
| 1465 | sti_font= [HW] |
| 1466 | See comment in drivers/video/console/sticore.c. |
| 1467 | |
| 1468 | stifb= [HW] |
| 1469 | Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]] |
| 1470 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1471 | swiotlb= [IA-64] Number of I/O TLB slabs |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1472 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1473 | switches= [HW,M68k] |
| 1474 | |
| 1475 | sym53c416= [HW,SCSI] |
| 1476 | See header of drivers/scsi/sym53c416.c. |
| 1477 | |
| 1478 | t128= [HW,SCSI] |
| 1479 | See header of drivers/scsi/t128.c. |
| 1480 | |
| 1481 | tdfx= [HW,DRM] |
| 1482 | |
| 1483 | thash_entries= [KNL,NET] |
| 1484 | Set number of hash buckets for TCP connection |
| 1485 | |
| 1486 | time Show timing data prefixed to each printk message line |
| 1487 | |
| 1488 | tipar.timeout= [HW,PPT] |
| 1489 | Set communications timeout in tenths of a second |
| 1490 | (default 15). |
| 1491 | |
| 1492 | tipar.delay= [HW,PPT] |
| 1493 | Set inter-bit delay in microseconds (default 10). |
| 1494 | |
| 1495 | tmc8xx= [HW,SCSI] |
| 1496 | See header of drivers/scsi/seagate.c. |
| 1497 | |
| 1498 | tmscsim= [HW,SCSI] |
| 1499 | See comment before function dc390_setup() in |
| 1500 | drivers/scsi/tmscsim.c. |
| 1501 | |
| 1502 | tp720= [HW,PS2] |
| 1503 | |
| 1504 | trix= [HW,OSS] MediaTrix AudioTrix Pro |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1505 | Format: |
| 1506 | <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq> |
| 1507 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1508 | tsdev.xres= [TS] Horizontal screen resolution. |
| 1509 | tsdev.yres= [TS] Vertical screen resolution. |
| 1510 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1511 | turbografx.map[2|3]= [HW,JOY] |
| 1512 | TurboGraFX parallel port interface |
| 1513 | Format: |
| 1514 | <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1515 | See also Documentation/input/joystick-parport.txt |
| 1516 | |
| 1517 | u14-34f= [HW,SCSI] UltraStor 14F/34F SCSI host adapter |
| 1518 | See header of drivers/scsi/u14-34f.c. |
| 1519 | |
| 1520 | uart401= [HW,OSS] |
| 1521 | Format: <io>,<irq> |
| 1522 | |
| 1523 | uart6850= [HW,OSS] |
| 1524 | Format: <io>,<irq> |
| 1525 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1526 | usbhid.mousepoll= |
| 1527 | [USBHID] The interval which mice are to be polled at. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1528 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1529 | video= [FB] Frame buffer configuration |
| 1530 | See Documentation/fb/modedb.txt. |
| 1531 | |
| 1532 | vga= [BOOT,IA-32] Select a particular video mode |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1533 | See Documentation/i386/boot.txt and |
| 1534 | Documentation/svga.txt. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1535 | Use vga=ask for menu. |
| 1536 | This is actually a boot loader parameter; the value is |
| 1537 | passed to the kernel using a special protocol. |
| 1538 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1539 | vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1540 | size of <nn>. This can be used to increase the |
| 1541 | minimum size (128MB on x86). It can also be used to |
| 1542 | decrease the size and leave more room for directly |
| 1543 | mapped kernel RAM. |
| 1544 | |
| 1545 | vmhalt= [KNL,S390] |
| 1546 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1547 | vmpoff= [KNL,S390] |
| 1548 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1549 | waveartist= [HW,OSS] |
| 1550 | Format: <io>,<irq>,<dma>,<dma2> |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1551 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1552 | wd33c93= [HW,SCSI] |
| 1553 | See header of drivers/scsi/wd33c93.c. |
| 1554 | |
| 1555 | wd7000= [HW,SCSI] |
| 1556 | See header of drivers/scsi/wd7000.c. |
| 1557 | |
| 1558 | wdt= [WDT] Watchdog |
| 1559 | See Documentation/watchdog/watchdog.txt. |
| 1560 | |
| 1561 | xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks. |
| 1562 | xd_geo= See header of drivers/block/xd.c. |
| 1563 | |
| 1564 | xirc2ps_cs= [NET,PCMCIA] |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1565 | Format: |
| 1566 | <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]] |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1567 | |
| 1568 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1569 | ______________________________________________________________________ |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1570 | Changelog: |
| 1571 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1572 | 2000-06-?? Mr. Unknown |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1573 | The last known update (for 2.4.0) - the changelog was not kept before. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1574 | |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1575 | 2002-11-24 Petr Baudis <pasky@ucw.cz> |
| 1576 | Randy Dunlap <randy.dunlap@verizon.net> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1577 | Update for 2.5.49, description for most of the options introduced, |
| 1578 | references to other documentation (C files, READMEs, ..), added S390, |
| 1579 | PPC, SPARC, MTD, ALSA and OSS category. Minor corrections and |
| 1580 | reformatting. |
Randy Dunlap | a991304 | 2005-10-23 12:57:11 -0700 | [diff] [blame] | 1581 | |
| 1582 | 2005-10-19 Randy Dunlap <rdunlap@xenotime.net> |
| 1583 | Lots of typos, whitespace, some reformatting. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1584 | |
| 1585 | TODO: |
| 1586 | |
| 1587 | Add documentation for ALSA options. |
| 1588 | Add more DRM drivers. |