blob: 4fdb81fa55e2f58964513f79eebbf8ef8a8c2382 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * mesh.h: definitions for the driver for the MESH SCSI bus adaptor
3 * (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers.
4 *
5 * Copyright (C) 1996 Paul Mackerras.
6 */
7#ifndef _MESH_H
8#define _MESH_H
9
10/*
11 * Registers in the MESH controller.
12 */
13
14struct mesh_regs {
15 unsigned char count_lo;
16 char pad0[15];
17 unsigned char count_hi;
18 char pad1[15];
19 unsigned char fifo;
20 char pad2[15];
21 unsigned char sequence;
22 char pad3[15];
23 unsigned char bus_status0;
24 char pad4[15];
25 unsigned char bus_status1;
26 char pad5[15];
27 unsigned char fifo_count;
28 char pad6[15];
29 unsigned char exception;
30 char pad7[15];
31 unsigned char error;
32 char pad8[15];
33 unsigned char intr_mask;
34 char pad9[15];
35 unsigned char interrupt;
36 char pad10[15];
37 unsigned char source_id;
38 char pad11[15];
39 unsigned char dest_id;
40 char pad12[15];
41 unsigned char sync_params;
42 char pad13[15];
43 unsigned char mesh_id;
44 char pad14[15];
45 unsigned char sel_timeout;
46 char pad15[15];
47};
48
49/* Bits in the sequence register. */
50#define SEQ_DMA_MODE 0x80 /* use DMA for data transfer */
51#define SEQ_TARGET 0x40 /* put the controller into target mode */
52#define SEQ_ATN 0x20 /* assert ATN signal */
53#define SEQ_ACTIVE_NEG 0x10 /* use active negation on REQ/ACK */
54#define SEQ_CMD 0x0f /* command bits: */
55#define SEQ_ARBITRATE 1 /* get the bus */
56#define SEQ_SELECT 2 /* select a target */
57#define SEQ_COMMAND 3 /* send a command */
58#define SEQ_STATUS 4 /* receive status */
59#define SEQ_DATAOUT 5 /* send data */
60#define SEQ_DATAIN 6 /* receive data */
61#define SEQ_MSGOUT 7 /* send a message */
62#define SEQ_MSGIN 8 /* receive a message */
63#define SEQ_BUSFREE 9 /* look for bus free */
64#define SEQ_ENBPARITY 0x0a /* enable parity checking */
65#define SEQ_DISPARITY 0x0b /* disable parity checking */
66#define SEQ_ENBRESEL 0x0c /* enable reselection */
67#define SEQ_DISRESEL 0x0d /* disable reselection */
68#define SEQ_RESETMESH 0x0e /* reset the controller */
69#define SEQ_FLUSHFIFO 0x0f /* clear out the FIFO */
70
71/* Bits in the bus_status0 and bus_status1 registers:
72 these correspond directly to the SCSI bus control signals. */
73#define BS0_REQ 0x20
74#define BS0_ACK 0x10
75#define BS0_ATN 0x08
76#define BS0_MSG 0x04
77#define BS0_CD 0x02
78#define BS0_IO 0x01
79#define BS1_RST 0x80
80#define BS1_BSY 0x40
81#define BS1_SEL 0x20
82
83/* Bus phases defined by the bits in bus_status0 */
84#define BS0_PHASE (BS0_MSG+BS0_CD+BS0_IO)
85#define BP_DATAOUT 0
86#define BP_DATAIN BS0_IO
87#define BP_COMMAND BS0_CD
88#define BP_STATUS (BS0_CD+BS0_IO)
89#define BP_MSGOUT (BS0_MSG+BS0_CD)
90#define BP_MSGIN (BS0_MSG+BS0_CD+BS0_IO)
91
92/* Bits in the exception register. */
93#define EXC_SELWATN 0x20 /* (as target) we were selected with ATN */
94#define EXC_SELECTED 0x10 /* (as target) we were selected w/o ATN */
95#define EXC_RESELECTED 0x08 /* (as initiator) we were reselected */
96#define EXC_ARBLOST 0x04 /* we lost arbitration */
97#define EXC_PHASEMM 0x02 /* SCSI phase mismatch */
98#define EXC_SELTO 0x01 /* selection timeout */
99
100/* Bits in the error register */
101#define ERR_UNEXPDISC 0x40 /* target unexpectedly disconnected */
102#define ERR_SCSIRESET 0x20 /* SCSI bus got reset on us */
103#define ERR_SEQERR 0x10 /* we did something the chip didn't like */
104#define ERR_PARITY 0x01 /* parity error was detected */
105
106/* Bits in the interrupt and intr_mask registers */
107#define INT_ERROR 0x04 /* error interrupt */
108#define INT_EXCEPTION 0x02 /* exception interrupt */
109#define INT_CMDDONE 0x01 /* command done interrupt */
110
111/* Fields in the sync_params register */
112#define SYNC_OFF(x) ((x) >> 4) /* offset field */
113#define SYNC_PER(x) ((x) & 0xf) /* period field */
114#define SYNC_PARAMS(o, p) (((o) << 4) | (p))
115#define ASYNC_PARAMS 2 /* sync_params value for async xfers */
116
117/*
118 * Assuming a clock frequency of 50MHz:
119 *
120 * The transfer period with SYNC_PER(sync_params) == x
121 * is (x + 2) * 40ns, except that x == 0 gives 100ns.
122 *
123 * The units of the sel_timeout register are 10ms.
124 */
125
126
127#endif /* _MESH_H */