blob: a5be9ac6405cfa27fcc918ae888fadd487902f40 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# Network device configuration
3#
4
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07005menuconfig NETDEVICES
Paolo 'Blaisorblade' Giarrussoce2d2ae2006-01-18 17:42:59 -08006 default y if UML
Jan Engelhardte0009822007-07-21 19:11:35 -07007 depends on NET
Linus Torvalds1da177e2005-04-16 15:20:36 -07008 bool "Network device support"
9 ---help---
10 You can say N here if you don't intend to connect your Linux box to
11 any other computer at all.
12
13 You'll have to say Y if your computer contains a network card that
14 you want to use under Linux. If you are going to run SLIP or PPP over
15 telephone line or null modem cable you need say Y here. Connecting
16 two machines with parallel ports using PLIP needs this, as well as
17 AX.25/KISS for sending Internet traffic over amateur radio links.
18
19 See also "The Linux Network Administrator's Guide" by Olaf Kirch and
20 Terry Dawson. Available at <http://www.tldp.org/guides.html>.
21
22 If unsure, say Y.
23
Randy Dunlap1618cb02006-09-25 23:11:21 -070024# All the following symbols are dependent on NETDEVICES - do not repeat
25# that for each of the symbols.
26if NETDEVICES
Randy Dunlapcbcd2a42005-07-27 13:04:35 -070027
Jamal Hadi Salim253af422006-01-08 22:34:25 -080028config IFB
29 tristate "Intermediate Functional Block support"
30 depends on NET_CLS_ACT
31 ---help---
Matt LaPlante3cb2fcc2006-11-30 05:22:59 +010032 This is an intermediate driver that allows sharing of
Jamal Hadi Salim253af422006-01-08 22:34:25 -080033 resources.
34 To compile this driver as a module, choose M here: the module
35 will be called ifb. If you want to use more than one ifb
36 device at a time, you need to compile this driver as a module.
37 Instead of 'ifb', the devices will then be called 'ifb0',
38 'ifb1' etc.
39 Look at the iproute2 documentation directory for usage etc
40
Linus Torvalds1da177e2005-04-16 15:20:36 -070041config DUMMY
42 tristate "Dummy net driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070043 ---help---
44 This is essentially a bit-bucket device (i.e. traffic you send to
45 this device is consigned into oblivion) with a configurable IP
46 address. It is most commonly used in order to make your currently
47 inactive SLIP address seem like a real address for local programs.
48 If you use SLIP or PPP, you might want to say Y here. Since this
49 thing often comes in handy, the default is Y. It won't enlarge your
50 kernel either. What a deal. Read about it in the Network
51 Administrator's Guide, available from
52 <http://www.tldp.org/docs.html#guide>.
53
54 To compile this driver as a module, choose M here: the module
55 will be called dummy. If you want to use more than one dummy
56 device at a time, you need to compile this driver as a module.
57 Instead of 'dummy', the devices will then be called 'dummy0',
58 'dummy1' etc.
59
60config BONDING
61 tristate "Bonding driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070062 depends on INET
Brian Haley305d5522008-11-04 17:51:14 -080063 depends on IPV6 || IPV6=n
Linus Torvalds1da177e2005-04-16 15:20:36 -070064 ---help---
65 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
66 Channels together. This is called 'Etherchannel' by Cisco,
67 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
68
69 The driver supports multiple bonding modes to allow for both high
Jon Mason47c51432006-02-12 11:53:04 -060070 performance and high availability operation.
Linus Torvalds1da177e2005-04-16 15:20:36 -070071
72 Refer to <file:Documentation/networking/bonding.txt> for more
73 information.
74
75 To compile this driver as a module, choose M here: the module
76 will be called bonding.
77
Patrick McHardyb863ceb2007-07-14 18:55:06 -070078config MACVLAN
79 tristate "MAC-VLAN support (EXPERIMENTAL)"
80 depends on EXPERIMENTAL
81 ---help---
82 This allows one to create virtual interfaces that map packets to
83 or from specific MAC addresses to a particular interface.
84
Patrick McHardy3dbf8d52008-02-26 17:52:05 -080085 Macvlan devices can be added using the "ip" command from the
86 iproute2 package starting with the iproute2-2.6.23 release:
87
88 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
89
Patrick McHardyb863ceb2007-07-14 18:55:06 -070090 To compile this driver as a module, choose M here: the module
91 will be called macvlan.
92
Linus Torvalds1da177e2005-04-16 15:20:36 -070093config EQUALIZER
94 tristate "EQL (serial line load balancing) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070095 ---help---
96 If you have two serial connections to some other computer (this
97 usually requires two modems and two telephone lines) and you use
98 SLIP (the protocol for sending Internet traffic over telephone
99 lines) or PPP (a better SLIP) on them, you can make them behave like
100 one double speed connection using this driver. Naturally, this has
101 to be supported at the other end as well, either with a similar EQL
102 Linux driver or with a Livingston Portmaster 2e.
103
104 Say Y if you want this and read
105 <file:Documentation/networking/eql.txt>. You may also want to read
106 section 6.2 of the NET-3-HOWTO, available from
107 <http://www.tldp.org/docs.html#howto>.
108
109 To compile this driver as a module, choose M here: the module
110 will be called eql. If unsure, say N.
111
112config TUN
113 tristate "Universal TUN/TAP device driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700114 select CRC32
115 ---help---
116 TUN/TAP provides packet reception and transmission for user space
117 programs. It can be viewed as a simple Point-to-Point or Ethernet
118 device, which instead of receiving packets from a physical media,
119 receives them from user space program and instead of sending packets
120 via physical media writes them to the user space program.
121
122 When a program opens /dev/net/tun, driver creates and registers
123 corresponding net device tunX or tapX. After a program closed above
124 devices, driver will automatically delete tunXX or tapXX device and
125 all routes corresponding to it.
126
127 Please read <file:Documentation/networking/tuntap.txt> for more
128 information.
129
130 To compile this driver as a module, choose M here: the module
131 will be called tun.
132
133 If you don't know what to use this for, you don't need it.
134
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700135config VETH
Rusty Russell6a9a0252007-11-06 20:35:55 -0800136 tristate "Virtual ethernet pair device"
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700137 ---help---
Rusty Russell6a9a0252007-11-06 20:35:55 -0800138 This device is a local ethernet tunnel. Devices are created in pairs.
139 When one end receives the packet it appears on its pair and vice
140 versa.
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700141
Linus Torvalds1da177e2005-04-16 15:20:36 -0700142config NET_SB1000
143 tristate "General Instruments Surfboard 1000"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -0700144 depends on PNP
Linus Torvalds1da177e2005-04-16 15:20:36 -0700145 ---help---
146 This is a driver for the General Instrument (also known as
147 NextLevel) SURFboard 1000 internal
148 cable modem. This is an ISA card which is used by a number of cable
149 TV companies to provide cable modem access. It's a one-way
150 downstream-only cable modem, meaning that your upstream net link is
151 provided by your regular phone modem.
152
153 At present this driver only compiles as a module, so say M here if
154 you have this card. The module will be called sb1000. Then read
155 <file:Documentation/networking/README.sb1000> for information on how
156 to use this module, as it needs special ppp scripts for establishing
157 a connection. Further documentation and the necessary scripts can be
158 found at:
159
160 <http://www.jacksonville.net/~fventuri/>
161 <http://home.adelphia.net/~siglercm/sb1000.html>
162 <http://linuxpower.cx/~cable/>
163
164 If you don't have this card, of course say N.
165
Adrian Bunkf65fd8f2006-01-05 22:45:41 -0800166source "drivers/net/arcnet/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700167
Andy Fleming00db8182005-07-30 19:31:23 -0400168source "drivers/net/phy/Kconfig"
169
Linus Torvalds1da177e2005-04-16 15:20:36 -0700170#
171# Ethernet
172#
173
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700174menuconfig NET_ETHERNET
Linus Torvalds1da177e2005-04-16 15:20:36 -0700175 bool "Ethernet (10 or 100Mbit)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700176 depends on !UML
Linus Torvalds1da177e2005-04-16 15:20:36 -0700177 ---help---
178 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
179 type of Local Area Network (LAN) in universities and companies.
180
181 Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
182 coaxial cable, linking computers in a chain), 10BASE-T or twisted
183 pair (10 Mbps over twisted pair cable, linking computers to central
184 hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
185 100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
186 100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
187 cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
188 [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
189 Ethernet (1 Gbps over optical fiber or short copper links).
190
191 If your Linux machine will be connected to an Ethernet and you have
192 an Ethernet network interface card (NIC) installed in your computer,
193 say Y here and read the Ethernet-HOWTO, available from
194 <http://www.tldp.org/docs.html#howto>. You will then also have
195 to say Y to the driver for your particular NIC.
196
197 Note that the answer to this question won't directly affect the
198 kernel: saying N will just cause the configurator to skip all
199 the questions about Ethernet network cards. If unsure, say N.
200
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700201if NET_ETHERNET
202
Linus Torvalds1da177e2005-04-16 15:20:36 -0700203config MII
204 tristate "Generic Media Independent Interface device support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700205 help
206 Most ethernet controllers have MII transceiver either as an external
207 or internal device. It is safe to say Y or M here even if your
208 ethernet card lack MII.
209
Haavard Skinnemoen89e57852006-11-09 14:51:17 +0100210config MACB
211 tristate "Atmel MACB support"
Nicolas Ferre789b23b2009-06-26 15:36:58 +0100212 depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
frederic RODO6c36a702007-07-12 19:07:24 +0200213 select PHYLIB
Haavard Skinnemoen89e57852006-11-09 14:51:17 +0100214 help
215 The Atmel MACB ethernet interface is found on many AT32 and AT91
216 parts. Say Y to include support for the MACB chip.
217
218 To compile this driver as a module, choose M here: the module
219 will be called macb.
220
Linus Torvalds1da177e2005-04-16 15:20:36 -0700221source "drivers/net/arm/Kconfig"
222
Ben Dooks825a2ff2007-07-03 16:53:09 +0100223config AX88796
224 tristate "ASIX AX88796 NE2000 clone support"
Magnus Damm86879912007-11-08 16:31:05 +0900225 depends on ARM || MIPS || SUPERH
Ben Dooks825a2ff2007-07-03 16:53:09 +0100226 select CRC32
227 select MII
228 help
229 AX88796 driver, using platform bus to provide
230 chip detection and resources
231
Magnus Damm89e536a2007-09-28 22:42:16 -0700232config AX88796_93CX6
233 bool "ASIX AX88796 external 93CX6 eeprom support"
234 depends on AX88796
235 select EEPROM_93CX6
236 help
237 Select this if your platform comes with an external 93CX6 eeprom.
238
Linus Torvalds1da177e2005-04-16 15:20:36 -0700239config MACE
240 tristate "MACE (Power Mac ethernet) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700241 depends on PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700242 select CRC32
243 help
244 Power Macintoshes and clones with Ethernet built-in on the
245 motherboard will usually use a MACE (Medium Access Control for
246 Ethernet) interface. Say Y to include support for the MACE chip.
247
248 To compile this driver as a module, choose M here: the module
249 will be called mace.
250
251config MACE_AAUI_PORT
252 bool "Use AAUI port instead of TP by default"
253 depends on MACE
254 help
255 Some Apple machines (notably the Apple Network Server) which use the
256 MACE ethernet chip have an Apple AUI port (small 15-pin connector),
257 instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say
258 Y here if you have such a machine. If unsure, say N.
259 The driver will default to AAUI on ANS anyway, and if you use it as
260 a module, you can provide the port_aaui=0|1 to force the driver.
261
262config BMAC
263 tristate "BMAC (G3 ethernet) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700264 depends on PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700265 select CRC32
266 help
267 Say Y for support of BMAC Ethernet interfaces. These are used on G3
268 computers.
269
270 To compile this driver as a module, choose M here: the module
271 will be called bmac.
272
Linus Torvalds1da177e2005-04-16 15:20:36 -0700273config ARIADNE
274 tristate "Ariadne support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700275 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700276 help
277 If you have a Village Tronic Ariadne Ethernet adapter, say Y.
278 Otherwise, say N.
279
280 To compile this driver as a module, choose M here: the module
281 will be called ariadne.
282
283config A2065
284 tristate "A2065 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700285 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700286 select CRC32
287 help
288 If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
289 say N.
290
291 To compile this driver as a module, choose M here: the module
292 will be called a2065.
293
294config HYDRA
295 tristate "Hydra support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700296 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700297 select CRC32
298 help
299 If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
300
301 To compile this driver as a module, choose M here: the module
302 will be called hydra.
303
304config ZORRO8390
305 tristate "Zorro NS8390-based Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700306 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700307 select CRC32
308 help
309 This driver is for Zorro Ethernet cards using an NS8390-compatible
310 chipset, like the Village Tronic Ariadne II and the Individual
311 Computers X-Surf Ethernet cards. If you have such a card, say Y.
312 Otherwise, say N.
313
314 To compile this driver as a module, choose M here: the module
315 will be called zorro8390.
316
317config APNE
318 tristate "PCMCIA NE2000 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700319 depends on AMIGA_PCMCIA
Linus Torvalds1da177e2005-04-16 15:20:36 -0700320 select CRC32
321 help
322 If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
323 say N.
324
325 To compile this driver as a module, choose M here: the module
326 will be called apne.
327
Linus Torvalds1da177e2005-04-16 15:20:36 -0700328config MAC8390
329 bool "Macintosh NS 8390 based ethernet cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700330 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700331 select CRC32
332 help
333 If you want to include a driver to support Nubus or LC-PDS
334 Ethernet cards using an NS8390 chipset or its equivalent, say Y
335 and read the Ethernet-HOWTO, available from
336 <http://www.tldp.org/docs.html#howto>.
337
338config MAC89x0
339 tristate "Macintosh CS89x0 based ethernet cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700340 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700341 ---help---
342 Support for CS89x0 chipset based Ethernet cards. If you have a
343 Nubus or LC-PDS network (Ethernet) card of this type, say Y and
344 read the Ethernet-HOWTO, available from
345 <http://www.tldp.org/docs.html#howto>.
346
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800347 To compile this driver as a module, choose M here. This module will
Linus Torvalds1da177e2005-04-16 15:20:36 -0700348 be called mac89x0.
349
350config MACSONIC
351 tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700352 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700353 ---help---
354 Support for NatSemi SONIC based Ethernet devices. This includes
355 the onboard Ethernet in many Quadras as well as some LC-PDS,
356 a few Nubus and all known Comm Slot Ethernet cards. If you have
357 one of these say Y and read the Ethernet-HOWTO, available from
358 <http://www.tldp.org/docs.html#howto>.
359
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800360 To compile this driver as a module, choose M here. This module will
Linus Torvalds1da177e2005-04-16 15:20:36 -0700361 be called macsonic.
362
363config MACMACE
Finn Thain8b6aaab2007-05-01 22:33:01 +0200364 bool "Macintosh (AV) onboard MACE ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700365 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700366 select CRC32
367 help
368 Support for the onboard AMD 79C940 MACE Ethernet controller used in
369 the 660AV and 840AV Macintosh. If you have one of these Macintoshes
370 say Y and read the Ethernet-HOWTO, available from
371 <http://www.tldp.org/docs.html#howto>.
372
373config MVME147_NET
374 tristate "MVME147 (Lance) Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700375 depends on MVME147
Linus Torvalds1da177e2005-04-16 15:20:36 -0700376 select CRC32
377 help
378 Support for the on-board Ethernet interface on the Motorola MVME147
379 single-board computer. Say Y here to include the
380 driver for this chip in your kernel.
381 To compile this driver as a module, choose M here.
382
383config MVME16x_NET
384 tristate "MVME16x Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700385 depends on MVME16x
Linus Torvalds1da177e2005-04-16 15:20:36 -0700386 help
387 This is the driver for the Ethernet interface on the Motorola
388 MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
389 driver for this chip in your kernel.
390 To compile this driver as a module, choose M here.
391
392config BVME6000_NET
393 tristate "BVME6000 Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700394 depends on BVME6000
Linus Torvalds1da177e2005-04-16 15:20:36 -0700395 help
396 This is the driver for the Ethernet interface on BVME4000 and
397 BVME6000 VME boards. Say Y here to include the driver for this chip
398 in your kernel.
399 To compile this driver as a module, choose M here.
400
401config ATARILANCE
402 tristate "Atari Lance support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700403 depends on ATARI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700404 help
405 Say Y to include support for several Atari Ethernet adapters based
406 on the AMD Lance chipset: RieblCard (with or without battery), or
407 PAMCard VME (also the version by Rhotron, with different addresses).
408
Linus Torvalds1da177e2005-04-16 15:20:36 -0700409config SUN3LANCE
410 tristate "Sun3/Sun3x on-board LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700411 depends on SUN3 || SUN3X
Linus Torvalds1da177e2005-04-16 15:20:36 -0700412 help
413 Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
414 featured an AMD Lance 10Mbit Ethernet controller on board; say Y
415 here to compile in the Linux driver for this and enable Ethernet.
416 General Linux information on the Sun 3 and 3x series (now
417 discontinued) is at
418 <http://www.angelfire.com/ca2/tech68k/sun3.html>.
419
420 If you're not building a kernel for a Sun 3, say N.
421
422config SUN3_82586
Al Viro9a482202005-08-25 06:24:56 +0100423 bool "Sun3 on-board Intel 82586 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700424 depends on SUN3
Linus Torvalds1da177e2005-04-16 15:20:36 -0700425 help
426 This driver enables support for the on-board Intel 82586 based
427 Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
428 that this driver does not support 82586-based adapters on additional
429 VME boards.
430
431config HPLANCE
432 bool "HP on-board LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700433 depends on DIO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700434 select CRC32
435 help
436 If you want to use the builtin "LANCE" Ethernet controller on an
437 HP300 machine, say Y here.
438
439config LASI_82596
440 tristate "Lasi ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700441 depends on GSC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700442 help
Matthew Wilcox6de187e2006-11-18 10:05:16 -0700443 Say Y here to support the builtin Intel 82596 ethernet controller
444 found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700445
Thomas Bogendoerferf2ec8032007-06-28 00:49:06 +0200446config SNI_82596
447 tristate "SNI RM ethernet"
448 depends on NET_ETHERNET && SNI_RM
449 help
450 Say Y here to support the on-board Intel 82596 ethernet controller
451 built into SNI RM machines.
452
Florian Fainellief112912008-03-19 17:14:51 +0100453config KORINA
454 tristate "Korina (IDT RC32434) Ethernet support"
Ralf Baechlef57b2062008-04-28 12:48:40 +0100455 depends on NET_ETHERNET && MIKROTIK_RB532
Florian Fainellief112912008-03-19 17:14:51 +0100456 help
457 If you have a Mikrotik RouterBoard 500 or IDT RC32434
458 based system say Y. Otherwise say N.
459
Linus Torvalds1da177e2005-04-16 15:20:36 -0700460config MIPS_JAZZ_SONIC
461 tristate "MIPS JAZZ onboard SONIC Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700462 depends on MACH_JAZZ
Linus Torvalds1da177e2005-04-16 15:20:36 -0700463 help
464 This is the driver for the onboard card of MIPS Magnum 4000,
465 Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
466
Chris Zankel74f2a5f02008-05-05 23:36:35 -0700467config XTENSA_XT2000_SONIC
468 tristate "Xtensa XT2000 onboard SONIC Ethernet support"
469 depends on XTENSA_PLATFORM_XT2000
470 help
471 This is the driver for the onboard card of the Xtensa XT2000 board.
472
Linus Torvalds1da177e2005-04-16 15:20:36 -0700473config MIPS_AU1X00_ENET
474 bool "MIPS AU1000 Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700475 depends on SOC_AU1X00
Herbert Valerio Riedel0638dec2006-06-01 09:41:04 +0200476 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -0700477 select CRC32
478 help
479 If you have an Alchemy Semi AU1X00 based system
480 say Y. Otherwise, say N.
481
Linus Torvalds1da177e2005-04-16 15:20:36 -0700482config SGI_IOC3_ETH
483 bool "SGI IOC3 Ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700484 depends on PCI && SGI_IP27
Linus Torvalds1da177e2005-04-16 15:20:36 -0700485 select CRC32
486 select MII
487 help
488 If you have a network (Ethernet) card of this type, say Y and read
489 the Ethernet-HOWTO, available from
490 <http://www.tldp.org/docs.html#howto>.
491
Ralf Baechledcbf8472005-10-10 14:51:27 +0100492config MIPS_SIM_NET
Ralf Baechle1e2b9802007-03-18 23:21:22 +0000493 tristate "MIPS simulator Network device"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700494 depends on MIPS_SIM
Ralf Baechledcbf8472005-10-10 14:51:27 +0100495 help
496 The MIPSNET device is a simple Ethernet network device which is
497 emulated by the MIPS Simulator.
498 If you are not using a MIPSsim or are unsure, say N.
499
Linus Torvalds1da177e2005-04-16 15:20:36 -0700500config SGI_O2MACE_ETH
501 tristate "SGI O2 MACE Fast Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700502 depends on SGI_IP32=y
Linus Torvalds1da177e2005-04-16 15:20:36 -0700503
504config STNIC
505 tristate "National DP83902AV support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700506 depends on SUPERH
Linus Torvalds1da177e2005-04-16 15:20:36 -0700507 select CRC32
508 help
509 Support for cards based on the National Semiconductor DP83902AV
510 ST-NIC Serial Network Interface Controller for Twisted Pair. This
511 is a 10Mbit/sec Ethernet controller. Product overview and specs at
512 <http://www.national.com/pf/DP/DP83902A.html>.
513
514 If unsure, say N.
515
Nobuhiro Iwamatsu86a74ff2008-06-09 16:33:56 -0700516config SH_ETH
517 tristate "Renesas SuperH Ethernet support"
518 depends on SUPERH && \
Yoshihiro Shimoda65ac8852009-05-24 23:54:30 +0000519 (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
520 CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
521 CPU_SUBTYPE_SH7724)
Nobuhiro Iwamatsu86a74ff2008-06-09 16:33:56 -0700522 select CRC32
523 select MII
524 select MDIO_BITBANG
525 select PHYLIB
526 help
527 Renesas SuperH Ethernet device driver.
Yoshihiro Shimoda65ac8852009-05-24 23:54:30 +0000528 This driver support SH7710, SH7712, SH7763, SH7619, and SH7724.
Nobuhiro Iwamatsu86a74ff2008-06-09 16:33:56 -0700529
Linus Torvalds1da177e2005-04-16 15:20:36 -0700530config SUNLANCE
531 tristate "Sun LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700532 depends on SBUS
Linus Torvalds1da177e2005-04-16 15:20:36 -0700533 select CRC32
534 help
535 This driver supports the "le" interface present on all 32-bit Sparc
536 systems, on some older Ultra systems and as an Sbus option. These
537 cards are based on the AMD Lance chipset, which is better known
538 via the NE2100 cards.
539
540 To compile this driver as a module, choose M here: the module
541 will be called sunlance.
542
543config HAPPYMEAL
544 tristate "Sun Happy Meal 10/100baseT support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700545 depends on SBUS || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700546 select CRC32
547 help
548 This driver supports the "hme" interface present on most Ultra
549 systems and as an option on older Sbus systems. This driver supports
550 both PCI and Sbus devices. This driver also supports the "qfe" quad
551 100baseT device available in both PCI and Sbus configurations.
552
553 To compile this driver as a module, choose M here: the module
554 will be called sunhme.
555
556config SUNBMAC
557 tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700558 depends on SBUS && EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -0700559 select CRC32
560 help
561 This driver supports the "be" interface available as an Sbus option.
562 This is Sun's older 100baseT Ethernet device.
563
564 To compile this driver as a module, choose M here: the module
565 will be called sunbmac.
566
567config SUNQE
568 tristate "Sun QuadEthernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700569 depends on SBUS
Linus Torvalds1da177e2005-04-16 15:20:36 -0700570 select CRC32
571 help
572 This driver supports the "qe" 10baseT Ethernet device, available as
573 an Sbus option. Note that this is not the same as Quad FastEthernet
574 "qfe" which is supported by the Happy Meal driver instead.
575
576 To compile this driver as a module, choose M here: the module
577 will be called sunqe.
578
579config SUNGEM
580 tristate "Sun GEM support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700581 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700582 select CRC32
583 help
584 Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
585 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.
586
David S. Miller1f26dac2005-09-27 15:24:13 -0700587config CASSINI
588 tristate "Sun Cassini support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700589 depends on PCI
David S. Miller1f26dac2005-09-27 15:24:13 -0700590 select CRC32
591 help
592 Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
593 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
594
David S. Miller4c521e42007-07-09 22:23:51 -0700595config SUNVNET
596 tristate "Sun Virtual Network support"
597 depends on SUN_LDOMS
598 help
599 Support for virtual network devices under Sun Logical Domains.
600
Linus Torvalds1da177e2005-04-16 15:20:36 -0700601config NET_VENDOR_3COM
602 bool "3COM cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700603 depends on ISA || EISA || MCA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700604 help
605 If you have a network (Ethernet) card belonging to this class, say Y
606 and read the Ethernet-HOWTO, available from
607 <http://www.tldp.org/docs.html#howto>.
608
609 Note that the answer to this question doesn't directly affect the
610 kernel: saying N will just cause the configurator to skip all
611 the questions about 3COM cards. If you say Y, you will be asked for
612 your specific card in the following questions.
613
614config EL1
615 tristate "3c501 \"EtherLink\" support"
616 depends on NET_VENDOR_3COM && ISA
617 ---help---
618 If you have a network (Ethernet) card of this type, say Y and read
619 the Ethernet-HOWTO, available from
620 <http://www.tldp.org/docs.html#howto>. Also, consider buying a
621 new card, since the 3c501 is slow, broken, and obsolete: you will
622 have problems. Some people suggest to ping ("man ping") a nearby
623 machine every minute ("man cron") when using this card.
624
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800625 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700626 will be called 3c501.
627
628config EL2
629 tristate "3c503 \"EtherLink II\" support"
630 depends on NET_VENDOR_3COM && ISA
631 select CRC32
632 help
633 If you have a network (Ethernet) card of this type, say Y and read
634 the Ethernet-HOWTO, available from
635 <http://www.tldp.org/docs.html#howto>.
636
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800637 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700638 will be called 3c503.
639
640config ELPLUS
641 tristate "3c505 \"EtherLink Plus\" support"
Al Viroa5532602005-05-04 05:39:42 +0100642 depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700643 ---help---
644 Information about this network (Ethernet) card can be found in
645 <file:Documentation/networking/3c505.txt>. If you have a card of
646 this type, say Y and read the Ethernet-HOWTO, available from
647 <http://www.tldp.org/docs.html#howto>.
648
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800649 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700650 will be called 3c505.
651
652config EL16
653 tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
654 depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
655 help
656 If you have a network (Ethernet) card of this type, say Y and read
657 the Ethernet-HOWTO, available from
658 <http://www.tldp.org/docs.html#howto>.
659
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800660 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700661 will be called 3c507.
662
663config EL3
664 tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
665 depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
666 ---help---
667 If you have a network (Ethernet) card belonging to the 3Com
668 EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
669 from <http://www.tldp.org/docs.html#howto>.
670
671 If your card is not working you may need to use the DOS
672 setup disk to disable Plug & Play mode, and to select the default
673 media type.
674
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800675 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700676 will be called 3c509.
677
678config 3C515
679 tristate "3c515 ISA \"Fast EtherLink\""
Al Viroa5532602005-05-04 05:39:42 +0100680 depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700681 help
682 If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
683 network card, say Y and read the Ethernet-HOWTO, available from
684 <http://www.tldp.org/docs.html#howto>.
685
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800686 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700687 will be called 3c515.
688
689config ELMC
690 tristate "3c523 \"EtherLink/MC\" support"
691 depends on NET_VENDOR_3COM && MCA_LEGACY
692 help
693 If you have a network (Ethernet) card of this type, say Y and read
694 the Ethernet-HOWTO, available from
695 <http://www.tldp.org/docs.html#howto>.
696
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800697 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700698 will be called 3c523.
699
700config ELMC_II
701 tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
702 depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
703 help
704 If you have a network (Ethernet) card of this type, say Y and read
705 the Ethernet-HOWTO, available from
706 <http://www.tldp.org/docs.html#howto>.
707
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800708 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700709 will be called 3c527.
710
711config VORTEX
712 tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
713 depends on NET_VENDOR_3COM && (PCI || EISA)
714 select MII
715 ---help---
Jon Mason47c51432006-02-12 11:53:04 -0600716 This option enables driver support for a large number of 10Mbps and
717 10/100Mbps EISA, PCI and PCMCIA 3Com network cards:
Linus Torvalds1da177e2005-04-16 15:20:36 -0700718
719 "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
720 "Boomerang" (EtherLink XL 3c900 or 3c905) PCI
721 "Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus
722 "Tornado" (3c905) PCI
723 "Hurricane" (3c555/3cSOHO) PCI
724
725 If you have such a card, say Y and read the Ethernet-HOWTO,
726 available from <http://www.tldp.org/docs.html#howto>. More
727 specific information is in
728 <file:Documentation/networking/vortex.txt> and in the comments at
729 the beginning of <file:drivers/net/3c59x.c>.
730
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800731 To compile this support as a module, choose M here.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700732
733config TYPHOON
734 tristate "3cr990 series \"Typhoon\" support"
735 depends on NET_VENDOR_3COM && PCI
736 select CRC32
737 ---help---
738 This option enables driver support for the 3cr990 series of cards:
739
740 3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
741 3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
742 3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR
743
744 If you have a network (Ethernet) card of this type, say Y and read
745 the Ethernet-HOWTO, available from
746 <http://www.tldp.org/docs.html#howto>.
747
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800748 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700749 will be called typhoon.
750
751config LANCE
752 tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700753 depends on ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700754 help
755 If you have a network (Ethernet) card of this type, say Y and read
756 the Ethernet-HOWTO, available from
757 <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
758 of this type.
759
760 To compile this driver as a module, choose M here: the module
761 will be called lance. This is recommended.
762
763config NET_VENDOR_SMC
764 bool "Western Digital/SMC cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700765 depends on ISA || MCA || EISA || MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700766 help
767 If you have a network (Ethernet) card belonging to this class, say Y
768 and read the Ethernet-HOWTO, available from
769 <http://www.tldp.org/docs.html#howto>.
770
771 Note that the answer to this question doesn't directly affect the
772 kernel: saying N will just cause the configurator to skip all
773 the questions about Western Digital cards. If you say Y, you will be
774 asked for your specific card in the following questions.
775
776config WD80x3
777 tristate "WD80*3 support"
778 depends on NET_VENDOR_SMC && ISA
779 select CRC32
780 help
781 If you have a network (Ethernet) card of this type, say Y and read
782 the Ethernet-HOWTO, available from
783 <http://www.tldp.org/docs.html#howto>.
784
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800785 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700786 will be called wd.
787
788config ULTRAMCA
789 tristate "SMC Ultra MCA support"
790 depends on NET_VENDOR_SMC && MCA
791 select CRC32
792 help
793 If you have a network (Ethernet) card of this type and are running
794 an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
795 available from <http://www.tldp.org/docs.html#howto>.
796
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800797 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700798 will be called smc-mca.
799
800config ULTRA
801 tristate "SMC Ultra support"
802 depends on NET_VENDOR_SMC && ISA
803 select CRC32
804 ---help---
805 If you have a network (Ethernet) card of this type, say Y and read
806 the Ethernet-HOWTO, available from
807 <http://www.tldp.org/docs.html#howto>.
808
809 Important: There have been many reports that, with some motherboards
810 mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
811 such as some BusLogic models) causes corruption problems with many
812 operating systems. The Linux smc-ultra driver has a work-around for
813 this but keep it in mind if you have such a SCSI card and have
814 problems.
815
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800816 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700817 will be called smc-ultra.
818
819config ULTRA32
820 tristate "SMC Ultra32 EISA support"
821 depends on NET_VENDOR_SMC && EISA
822 select CRC32
823 help
824 If you have a network (Ethernet) card of this type, say Y and read
825 the Ethernet-HOWTO, available from
826 <http://www.tldp.org/docs.html#howto>.
827
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800828 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700829 will be called smc-ultra32.
830
Bryan Wue190d6b2007-07-17 14:43:44 +0800831config BFIN_MAC
Mike Frysinger736783b2008-08-27 11:47:57 +0800832 tristate "Blackfin on-chip MAC support"
Sonic Zhang33a2a2b2009-01-08 10:52:26 -0800833 depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
Bryan Wue190d6b2007-07-17 14:43:44 +0800834 select CRC32
Bryan Wueeb70af2007-09-19 23:37:41 +0800835 select MII
836 select PHYLIB
Bryan Wue190d6b2007-07-17 14:43:44 +0800837 select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
838 help
Mike Frysinger736783b2008-08-27 11:47:57 +0800839 This is the driver for Blackfin on-chip mac device. Say Y if you want it
Bryan Wue190d6b2007-07-17 14:43:44 +0800840 compiled into the kernel. This driver is also available as a module
841 ( = code which can be inserted in and removed from the running kernel
842 whenever you want). The module will be called bfin_mac.
843
844config BFIN_MAC_USE_L1
845 bool "Use L1 memory for rx/tx packets"
Michael Hennerich6893ff12008-01-30 16:52:25 +0800846 depends on BFIN_MAC && (BF527 || BF537)
Bryan Wue190d6b2007-07-17 14:43:44 +0800847 default y
848 help
Matt LaPlante01dd2fb2007-10-20 01:34:40 +0200849 To get maximum network performance, you should use L1 memory as rx/tx buffers.
Bryan Wue190d6b2007-07-17 14:43:44 +0800850 Say N here if you want to reserve L1 memory for other uses.
851
852config BFIN_TX_DESC_NUM
853 int "Number of transmit buffer packets"
854 depends on BFIN_MAC
855 range 6 10 if BFIN_MAC_USE_L1
856 range 10 100
857 default "10"
858 help
859 Set the number of buffer packets used in driver.
860
861config BFIN_RX_DESC_NUM
862 int "Number of receive buffer packets"
863 depends on BFIN_MAC
864 range 20 100 if BFIN_MAC_USE_L1
865 range 20 800
866 default "20"
867 help
868 Set the number of buffer packets used in driver.
869
870config BFIN_MAC_RMII
871 bool "RMII PHY Interface (EXPERIMENTAL)"
872 depends on BFIN_MAC && EXPERIMENTAL
Michael Hennerich6893ff12008-01-30 16:52:25 +0800873 default y if BFIN527_EZKIT
874 default n if BFIN537_STAMP
Bryan Wue190d6b2007-07-17 14:43:44 +0800875 help
876 Use Reduced PHY MII Interface
877
Linus Torvalds1da177e2005-04-16 15:20:36 -0700878config SMC9194
879 tristate "SMC 9194 support"
880 depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
881 select CRC32
882 ---help---
883 This is support for the SMC9xxx based Ethernet cards. Choose this
884 option if you have a DELL laptop with the docking station, or
885 another SMC9192/9194 based chipset. Say Y if you want it compiled
886 into the kernel, and read the file
887 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
888 available from <http://www.tldp.org/docs.html#howto>.
889
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800890 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700891 will be called smc9194.
892
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700893config SMC91X
894 tristate "SMC 91C9x/91C1xxx support"
895 select CRC32
896 select MII
David Howellsb920de12008-02-08 04:19:31 -0800897 depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
Atsushi Nemotocde0d912008-10-21 00:00:29 +0900898 MIPS || BLACKFIN || MN10300
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700899 help
900 This is a driver for SMC's 91x series of Ethernet chipsets,
901 including the SMC91C94 and the SMC91C111. Say Y if you want it
902 compiled into the kernel, and read the file
903 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
904 available from <http://www.linuxdoc.org/docs.html#howto>.
905
906 This driver is also available as a module ( = code which can be
907 inserted in and removed from the running kernel whenever you want).
908 The module will be called smc91x. If you want to compile it as a
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800909 module, say M here and read <file:Documentation/kbuild/modules.txt>.
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700910
Sascha Hauer92aa6742006-06-22 07:11:13 +0200911config NET_NETX
912 tristate "NetX Ethernet support"
913 select MII
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700914 depends on ARCH_NETX
Sascha Hauer92aa6742006-06-22 07:11:13 +0200915 help
916 This is support for the Hilscher netX builtin Ethernet ports
917
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800918 To compile this driver as a module, choose M here. The module
Sascha Hauer92aa6742006-06-22 07:11:13 +0200919 will be called netx-eth.
920
Anant Golea6286ee2009-05-18 15:19:01 -0700921config TI_DAVINCI_EMAC
922 tristate "TI DaVinci EMAC Support"
923 depends on ARM && ARCH_DAVINCI
924 select PHYLIB
925 help
926 This driver supports TI's DaVinci Ethernet .
927
928 To compile this driver as a module, choose M here: the module
929 will be called davinci_emac_driver. This is recommended.
930
Sascha Hauera1365272005-05-05 15:14:15 -0700931config DM9000
932 tristate "DM9000 support"
Alex Landauf40d24d2007-07-12 12:11:48 +0800933 depends on ARM || BLACKFIN || MIPS
Sascha Hauera1365272005-05-05 15:14:15 -0700934 select CRC32
935 select MII
936 ---help---
937 Support for DM9000 chipset.
938
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800939 To compile this driver as a module, choose M here. The module
940 will be called dm9000.
Sascha Hauera1365272005-05-05 15:14:15 -0700941
Ben Dooks485ca222008-06-24 22:16:06 +0100942config DM9000_DEBUGLEVEL
943 int "DM9000 maximum debug level"
944 depends on DM9000
945 default 4
946 help
947 The maximum level of debugging code compiled into the DM9000
948 driver.
949
Ben Dooksf8dd0ec2008-06-24 22:16:04 +0100950config DM9000_FORCE_SIMPLE_PHY_POLL
951 bool "Force simple NSR based PHY polling"
952 depends on DM9000
953 ---help---
954 This configuration forces the DM9000 to use the NSR's LinkStatus
955 bit to determine if the link is up or down instead of the more
956 costly MII PHY reads. Note, this will not work if the chip is
957 operating with an external PHY.
958
Claudio Lanconelli3ec9c112008-01-14 11:00:28 +0100959config ENC28J60
960 tristate "ENC28J60 support"
961 depends on EXPERIMENTAL && SPI && NET_ETHERNET
962 select CRC32
963 ---help---
964 Support for the Microchip EN28J60 ethernet chip.
965
Johann Felix Soden2bfc79d2008-02-05 03:13:58 -0800966 To compile this driver as a module, choose M here. The module will be
Claudio Lanconelli3ec9c112008-01-14 11:00:28 +0100967 called enc28j60.
968
969config ENC28J60_WRITEVERIFY
970 bool "Enable write verify"
971 depends on ENC28J60
972 ---help---
973 Enable the verify after the buffer write useful for debugging purpose.
974 If unsure, say N.
975
Thierry Redinga1702852009-03-27 00:12:24 -0700976config ETHOC
977 tristate "OpenCores 10/100 Mbps Ethernet MAC support"
Geert Uytterhoeven0ebe74e2009-11-20 09:19:10 +0000978 depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
Thierry Redinga1702852009-03-27 00:12:24 -0700979 select MII
980 select PHYLIB
Randy Dunlapc5cacb32009-04-08 15:41:25 -0700981 select CRC32
982 select BITREVERSE
Thierry Redinga1702852009-03-27 00:12:24 -0700983 help
984 Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
985
Dustin McIntire0a0c72c2006-04-19 20:24:51 -0700986config SMC911X
987 tristate "SMSC LAN911[5678] support"
988 select CRC32
989 select MII
Catalin Marinasbd2c4972008-10-20 18:15:17 +0100990 depends on ARM || SUPERH
Dustin McIntire0a0c72c2006-04-19 20:24:51 -0700991 help
992 This is a driver for SMSC's LAN911x series of Ethernet chipsets
993 including the new LAN9115, LAN9116, LAN9117, and LAN9118.
994 Say Y if you want it compiled into the kernel,
995 and read the Ethernet-HOWTO, available from
996 <http://www.linuxdoc.org/docs.html#howto>.
997
998 This driver is also available as a module. The module will be
999 called smc911x. If you want to compile it as a module, say M
Alexander E. Patrakov39f5fb32007-03-16 18:28:43 +05001000 here and read <file:Documentation/kbuild/modules.txt>
Dustin McIntire0a0c72c2006-04-19 20:24:51 -07001001
Steve Glendinningfd9abb32008-11-05 00:35:37 +00001002config SMSC911X
1003 tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
Manuel Laussb4efc562009-10-13 07:25:48 +00001004 depends on ARM || SUPERH || BLACKFIN || MIPS
Steve Glendinningfd9abb32008-11-05 00:35:37 +00001005 select CRC32
1006 select MII
1007 select PHYLIB
1008 ---help---
1009 Say Y here if you want support for SMSC LAN911x and LAN921x families
1010 of ethernet controllers.
1011
1012 To compile this driver as a module, choose M here and read
1013 <file:Documentation/networking/net-modules.txt>. The module
1014 will be called smsc911x.
1015
Linus Torvalds1da177e2005-04-16 15:20:36 -07001016config NET_VENDOR_RACAL
1017 bool "Racal-Interlan (Micom) NI cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001018 depends on ISA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001019 help
1020 If you have a network (Ethernet) card belonging to this class, such
1021 as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
1022 available from <http://www.tldp.org/docs.html#howto>.
1023
1024 Note that the answer to this question doesn't directly affect the
1025 kernel: saying N will just cause the configurator to skip all
1026 the questions about NI cards. If you say Y, you will be asked for
1027 your specific card in the following questions.
1028
1029config NI5010
1030 tristate "NI5010 support (EXPERIMENTAL)"
1031 depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
1032 ---help---
1033 If you have a network (Ethernet) card of this type, say Y and read
1034 the Ethernet-HOWTO, available from
1035 <http://www.tldp.org/docs.html#howto>. Note that this is still
1036 experimental code.
1037
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001038 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001039 will be called ni5010.
1040
1041config NI52
1042 tristate "NI5210 support"
1043 depends on NET_VENDOR_RACAL && ISA
1044 help
1045 If you have a network (Ethernet) card of this type, say Y and read
1046 the Ethernet-HOWTO, available from
1047 <http://www.tldp.org/docs.html#howto>.
1048
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001049 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001050 will be called ni52.
1051
1052config NI65
1053 tristate "NI6510 support"
Al Viroa5532602005-05-04 05:39:42 +01001054 depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -07001055 help
1056 If you have a network (Ethernet) card of this type, say Y and read
1057 the Ethernet-HOWTO, available from
1058 <http://www.tldp.org/docs.html#howto>.
1059
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001060 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001061 will be called ni65.
1062
Ilya Yanok47964172009-03-11 23:26:02 -07001063config DNET
1064 tristate "Dave ethernet support (DNET)"
Ilya Yanok4b979262009-03-21 16:58:47 -07001065 depends on NET_ETHERNET && HAS_IOMEM
Ilya Yanok47964172009-03-11 23:26:02 -07001066 select PHYLIB
1067 help
1068 The Dave ethernet interface (DNET) is found on Qong Board FPGA.
1069 Say Y to include support for the DNET chip.
1070
1071 To compile this driver as a module, choose M here: the module
1072 will be called dnet.
1073
Linus Torvalds1da177e2005-04-16 15:20:36 -07001074source "drivers/net/tulip/Kconfig"
1075
1076config AT1700
1077 tristate "AT1700/1720 support (EXPERIMENTAL)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001078 depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07001079 select CRC32
1080 ---help---
1081 If you have a network (Ethernet) card of this type, say Y and read
1082 the Ethernet-HOWTO, available from
1083 <http://www.tldp.org/docs.html#howto>.
1084
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001085 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001086 will be called at1700.
1087
1088config DEPCA
1089 tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001090 depends on ISA || EISA || MCA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001091 select CRC32
1092 ---help---
1093 If you have a network (Ethernet) card of this type, say Y and read
1094 the Ethernet-HOWTO, available from
1095 <http://www.tldp.org/docs.html#howto> as well as
1096 <file:drivers/net/depca.c>.
1097
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001098 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001099 will be called depca.
1100
1101config HP100
1102 tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001103 depends on ISA || EISA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001104 help
1105 If you have a network (Ethernet) card of this type, say Y and read
1106 the Ethernet-HOWTO, available from
1107 <http://www.tldp.org/docs.html#howto>.
1108
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001109 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001110 will be called hp100.
1111
1112config NET_ISA
1113 bool "Other ISA cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001114 depends on ISA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001115 ---help---
1116 If your network (Ethernet) card hasn't been mentioned yet and its
1117 bus system (that's the way the cards talks to the other components
1118 of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
1119 Make sure you know the name of your card. Read the Ethernet-HOWTO,
1120 available from <http://www.tldp.org/docs.html#howto>.
1121
1122 If unsure, say Y.
1123
1124 Note that the answer to this question doesn't directly affect the
1125 kernel: saying N will just cause the configurator to skip all
1126 the remaining ISA network card questions. If you say Y, you will be
1127 asked for your specific card in the following questions.
1128
1129config E2100
1130 tristate "Cabletron E21xx support"
1131 depends on NET_ISA
1132 select CRC32
1133 help
1134 If you have a network (Ethernet) card of this type, say Y and read
1135 the Ethernet-HOWTO, available from
1136 <http://www.tldp.org/docs.html#howto>.
1137
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001138 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001139 will be called e2100.
1140
1141config EWRK3
1142 tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
1143 depends on NET_ISA
1144 select CRC32
1145 ---help---
1146 This driver supports the DE203, DE204 and DE205 network (Ethernet)
1147 cards. If this is for you, say Y and read
1148 <file:Documentation/networking/ewrk3.txt> in the kernel source as
1149 well as the Ethernet-HOWTO, available from
1150 <http://www.tldp.org/docs.html#howto>.
1151
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001152 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001153 will be called ewrk3.
1154
1155config EEXPRESS
1156 tristate "EtherExpress 16 support"
1157 depends on NET_ISA
1158 ---help---
1159 If you have an EtherExpress16 network (Ethernet) card, say Y and
1160 read the Ethernet-HOWTO, available from
1161 <http://www.tldp.org/docs.html#howto>. Note that the Intel
1162 EtherExpress16 card used to be regarded as a very poor choice
1163 because the driver was very unreliable. We now have a new driver
1164 that should do better.
1165
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001166 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001167 will be called eexpress.
1168
1169config EEXPRESS_PRO
1170 tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
1171 depends on NET_ISA
1172 ---help---
1173 If you have a network (Ethernet) card of this type, say Y. This
Jon Mason47c51432006-02-12 11:53:04 -06001174 driver supports Intel i82595{FX,TX} based boards. Note however
Linus Torvalds1da177e2005-04-16 15:20:36 -07001175 that the EtherExpress PRO/100 Ethernet card has its own separate
1176 driver. Please read the Ethernet-HOWTO, available from
1177 <http://www.tldp.org/docs.html#howto>.
1178
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001179 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001180 will be called eepro.
1181
Linus Torvalds1da177e2005-04-16 15:20:36 -07001182config HPLAN_PLUS
1183 tristate "HP PCLAN+ (27247B and 27252A) support"
1184 depends on NET_ISA
1185 select CRC32
1186 help
1187 If you have a network (Ethernet) card of this type, say Y and read
1188 the Ethernet-HOWTO, available from
1189 <http://www.tldp.org/docs.html#howto>.
1190
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001191 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001192 will be called hp-plus.
1193
1194config HPLAN
1195 tristate "HP PCLAN (27245 and other 27xxx series) support"
1196 depends on NET_ISA
1197 select CRC32
1198 help
1199 If you have a network (Ethernet) card of this type, say Y and read
1200 the Ethernet-HOWTO, available from
1201 <http://www.tldp.org/docs.html#howto>.
1202
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001203 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001204 will be called hp.
1205
1206config LP486E
1207 tristate "LP486E on board Ethernet"
1208 depends on NET_ISA
1209 help
1210 Say Y here to support the 82596-based on-board Ethernet controller
1211 for the Panther motherboard, which is one of the two shipped in the
1212 Intel Professional Workstation.
1213
1214config ETH16I
1215 tristate "ICL EtherTeam 16i/32 support"
1216 depends on NET_ISA
1217 help
1218 If you have a network (Ethernet) card of this type, say Y and read
1219 the Ethernet-HOWTO, available from
1220 <http://www.tldp.org/docs.html#howto>.
1221
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001222 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001223 will be called eth16i.
1224
1225config NE2000
1226 tristate "NE2000/NE1000 support"
Atsushi Nemotoc7e65c12008-08-08 00:55:17 +09001227 depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
Linus Torvalds1da177e2005-04-16 15:20:36 -07001228 select CRC32
1229 ---help---
1230 If you have a network (Ethernet) card of this type, say Y and read
1231 the Ethernet-HOWTO, available from
1232 <http://www.tldp.org/docs.html#howto>. Many Ethernet cards
1233 without a specific driver are compatible with NE2000.
1234
1235 If you have a PCI NE2000 card however, say N here and Y to "PCI
Jesper Juhl28beaf62006-03-08 00:06:31 -08001236 NE2000 and clone support" under "EISA, VLB, PCI and on board
1237 controllers" below. If you have a NE2000 card and are running on
Linus Torvalds1da177e2005-04-16 15:20:36 -07001238 an MCA system (a bus system used on some IBM PS/2 computers and
1239 laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
1240 below.
1241
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001242 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001243 will be called ne.
1244
1245config ZNET
1246 tristate "Zenith Z-Note support (EXPERIMENTAL)"
Al Viroa5532602005-05-04 05:39:42 +01001247 depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -07001248 help
1249 The Zenith Z-Note notebook computer has a built-in network
1250 (Ethernet) card, and this is the Linux driver for it. Note that the
1251 IBM Thinkpad 300 is compatible with the Z-Note and is also supported
1252 by this driver. Read the Ethernet-HOWTO, available from
1253 <http://www.tldp.org/docs.html#howto>.
1254
1255config SEEQ8005
1256 tristate "SEEQ8005 support (EXPERIMENTAL)"
1257 depends on NET_ISA && EXPERIMENTAL
1258 help
1259 This is a driver for the SEEQ 8005 network (Ethernet) card. If this
1260 is for you, read the Ethernet-HOWTO, available from
1261 <http://www.tldp.org/docs.html#howto>.
1262
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001263 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001264 will be called seeq8005.
1265
Linus Torvalds1da177e2005-04-16 15:20:36 -07001266config NE2_MCA
1267 tristate "NE/2 (ne2000 MCA version) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001268 depends on MCA_LEGACY
Linus Torvalds1da177e2005-04-16 15:20:36 -07001269 select CRC32
1270 help
1271 If you have a network (Ethernet) card of this type, say Y and read
1272 the Ethernet-HOWTO, available from
1273 <http://www.tldp.org/docs.html#howto>.
1274
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001275 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001276 will be called ne2.
1277
1278config IBMLANA
1279 tristate "IBM LAN Adapter/A support"
Adrian Bunke6353f32008-01-30 22:02:35 +02001280 depends on MCA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001281 ---help---
1282 This is a Micro Channel Ethernet adapter. You need to set
1283 CONFIG_MCA to use this driver. It is both available as an in-kernel
1284 driver and as a module.
1285
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001286 To compile this driver as a module, choose M here. The only
Linus Torvalds1da177e2005-04-16 15:20:36 -07001287 currently supported card is the IBM LAN Adapter/A for Ethernet. It
1288 will both support 16K and 32K memory windows, however a 32K window
1289 gives a better security against packet losses. Usage of multiple
1290 boards with this driver should be possible, but has not been tested
1291 up to now due to lack of hardware.
1292
1293config IBMVETH
1294 tristate "IBM LAN Virtual Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001295 depends on PPC_PSERIES
Linus Torvalds1da177e2005-04-16 15:20:36 -07001296 ---help---
1297 This driver supports virtual ethernet adapters on newer IBM iSeries
1298 and pSeries systems.
1299
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001300 To compile this driver as a module, choose M here. The module will
Linus Torvalds1da177e2005-04-16 15:20:36 -07001301 be called ibmveth.
1302
David Gibson1d3bb992007-08-23 13:56:01 +10001303source "drivers/net/ibm_newemac/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001304
1305config NET_PCI
1306 bool "EISA, VLB, PCI and on board controllers"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001307 depends on ISA || EISA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001308 help
1309 This is another class of network cards which attach directly to the
1310 bus. If you have one of those, say Y and read the Ethernet-HOWTO,
1311 available from <http://www.tldp.org/docs.html#howto>.
1312
1313 Note that the answer to this question doesn't directly affect the
1314 kernel: saying N will just cause the configurator to skip all
1315 the questions about this class of network cards. If you say Y, you
1316 will be asked for your specific card in the following questions. If
1317 you are unsure, say Y.
1318
1319config PCNET32
1320 tristate "AMD PCnet32 PCI support"
1321 depends on NET_PCI && PCI
1322 select CRC32
1323 select MII
1324 help
1325 If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
1326 answer Y here and read the Ethernet-HOWTO, available from
1327 <http://www.tldp.org/docs.html#howto>.
1328
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001329 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001330 will be called pcnet32.
1331
1332config AMD8111_ETH
1333 tristate "AMD 8111 (new PCI lance) support"
1334 depends on NET_PCI && PCI
1335 select CRC32
1336 select MII
1337 help
1338 If you have an AMD 8111-based PCI lance ethernet card,
1339 answer Y here and read the Ethernet-HOWTO, available from
1340 <http://www.tldp.org/docs.html#howto>.
1341
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001342 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001343 will be called amd8111e.
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001344
Linus Torvalds1da177e2005-04-16 15:20:36 -07001345config ADAPTEC_STARFIRE
1346 tristate "Adaptec Starfire/DuraLAN support"
1347 depends on NET_PCI && PCI
1348 select CRC32
1349 select MII
1350 help
1351 Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
1352 adapter. The DuraLAN chip is used on the 64 bit PCI boards from
1353 Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
1354 driver.
1355
1356 To compile this driver as a module, choose M here: the module
1357 will be called starfire. This is recommended.
1358
Linus Torvalds1da177e2005-04-16 15:20:36 -07001359config AC3200
1360 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
1361 depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
1362 select CRC32
1363 help
1364 If you have a network (Ethernet) card of this type, say Y and read
1365 the Ethernet-HOWTO, available from
1366 <http://www.tldp.org/docs.html#howto>.
1367
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001368 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001369 will be called ac3200.
1370
1371config APRICOT
1372 tristate "Apricot Xen-II on board Ethernet"
1373 depends on NET_PCI && ISA
1374 help
1375 If you have a network (Ethernet) controller of this type, say Y and
1376 read the Ethernet-HOWTO, available from
1377 <http://www.tldp.org/docs.html#howto>.
1378
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001379 To compile this driver as a module, choose M here. The module
1380 will be called apricot.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001381
1382config B44
Michael Buesch753f4922007-09-19 14:20:30 -07001383 tristate "Broadcom 440x/47xx ethernet support"
Al Viro46cb69c2008-05-21 06:32:11 +01001384 depends on SSB_POSSIBLE && HAS_DMA
Michael Buesch753f4922007-09-19 14:20:30 -07001385 select SSB
Linus Torvalds1da177e2005-04-16 15:20:36 -07001386 select MII
1387 help
Michael Buesch753f4922007-09-19 14:20:30 -07001388 If you have a network (Ethernet) controller of this type, say Y
1389 or M and read the Ethernet-HOWTO, available from
Linus Torvalds1da177e2005-04-16 15:20:36 -07001390 <http://www.tldp.org/docs.html#howto>.
1391
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001392 To compile this driver as a module, choose M here. The module
1393 will be called b44.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001394
Michael Buesch753f4922007-09-19 14:20:30 -07001395# Auto-select SSB PCI-HOST support, if possible
1396config B44_PCI_AUTOSELECT
1397 bool
1398 depends on B44 && SSB_PCIHOST_POSSIBLE
1399 select SSB_PCIHOST
1400 default y
1401
1402# Auto-select SSB PCICORE driver, if possible
1403config B44_PCICORE_AUTOSELECT
1404 bool
1405 depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
1406 select SSB_DRIVER_PCICORE
1407 default y
1408
1409config B44_PCI
1410 bool
1411 depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
1412 default y
1413
Linus Torvalds1da177e2005-04-16 15:20:36 -07001414config FORCEDETH
Adrian Bunk82770082006-03-08 00:06:30 -08001415 tristate "nForce Ethernet support"
1416 depends on NET_PCI && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001417 help
1418 If you have a network (Ethernet) controller of this type, say Y and
1419 read the Ethernet-HOWTO, available from
1420 <http://www.tldp.org/docs.html#howto>.
1421
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001422 To compile this driver as a module, choose M here. The module
1423 will be called forcedeth.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001424
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001425config FORCEDETH_NAPI
Randy Dunlapbf45abe2007-10-18 17:16:20 -07001426 bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001427 depends on FORCEDETH && EXPERIMENTAL
1428 help
1429 NAPI is a new driver API designed to reduce CPU and interrupt load
1430 when the driver is receiving lots of packets from the card. It is
1431 still somewhat experimental and thus not yet enabled by default.
1432
1433 If your estimated Rx load is 10kpps or more, or if the card will be
1434 deployed on potentially unfriendly networks (e.g. in a firewall),
1435 then say Y here.
1436
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001437 If in doubt, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001438
1439config CS89x0
1440 tristate "CS89x0 support"
Gilles Chanteperdrix0ac4ed92008-09-26 15:44:43 +01001441 depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
1442 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001443 ---help---
1444 Support for CS89x0 chipset based Ethernet cards. If you have a
1445 network (Ethernet) card of this type, say Y and read the
1446 Ethernet-HOWTO, available from
1447 <http://www.tldp.org/docs.html#howto> as well as
1448 <file:Documentation/networking/cs89x0.txt>.
1449
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001450 To compile this driver as a module, choose M here. The module
1451 will be called cs89x0.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001452
Gilles Chanteperdrix0ac4ed92008-09-26 15:44:43 +01001453config CS89x0_NONISA_IRQ
1454 def_bool y
1455 depends on CS89x0 != n
1456 depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS
1457
Linus Torvalds1da177e2005-04-16 15:20:36 -07001458config TC35815
1459 tristate "TOSHIBA TC35815 Ethernet support"
Atsushi Nemotoeea221ce2007-03-03 23:54:59 +09001460 depends on NET_PCI && PCI && MIPS
Atsushi Nemotoc6686fe2008-04-12 00:47:46 +09001461 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -07001462
Linus Torvalds1da177e2005-04-16 15:20:36 -07001463config E100
1464 tristate "Intel(R) PRO/100+ support"
1465 depends on NET_PCI && PCI
1466 select MII
1467 ---help---
1468 This driver supports Intel(R) PRO/100 family of adapters.
1469 To verify that your adapter is supported, find the board ID number
1470 on the adapter. Look for a label that has a barcode and a number
1471 in the format 123456-001 (six digits hyphen three digits).
1472
1473 Use the above information and the Adapter & Driver ID Guide at:
1474
1475 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
1476
1477 to identify the adapter.
1478
1479 For the latest Intel PRO/100 network driver for Linux, see:
1480
1481 <http://appsr.intel.com/scripts-df/support_intel.asp>
1482
1483 More specific information on configuring the driver is in
1484 <file:Documentation/networking/e100.txt>.
1485
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001486 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001487 will be called e100.
1488
1489config LNE390
1490 tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
1491 depends on NET_PCI && EISA && EXPERIMENTAL
1492 select CRC32
1493 help
1494 If you have a network (Ethernet) card of this type, say Y and read
1495 the Ethernet-HOWTO, available from
1496 <http://www.tldp.org/docs.html#howto>.
1497
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001498 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001499 will be called lne390.
1500
1501config FEALNX
1502 tristate "Myson MTD-8xx PCI Ethernet support"
1503 depends on NET_PCI && PCI
1504 select CRC32
1505 select MII
1506 help
1507 Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
1508 cards. Specifications and data at
1509 <http://www.myson.com.hk/mtd/datasheet/>.
1510
1511config NATSEMI
1512 tristate "National Semiconductor DP8381x series PCI Ethernet support"
1513 depends on NET_PCI && PCI
1514 select CRC32
1515 help
1516 This driver is for the National Semiconductor DP83810 series,
1517 which is used in cards from PureData, NetGear, Linksys
1518 and others, including the 83815 chip.
1519 More specific information and updates are available from
1520 <http://www.scyld.com/network/natsemi.html>.
1521
1522config NE2K_PCI
1523 tristate "PCI NE2000 and clones support (see help)"
1524 depends on NET_PCI && PCI
1525 select CRC32
1526 ---help---
1527 This driver is for NE2000 compatible PCI cards. It will not work
1528 with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
1529 support" below). If you have a PCI NE2000 network (Ethernet) card,
1530 say Y and read the Ethernet-HOWTO, available from
1531 <http://www.tldp.org/docs.html#howto>.
1532
1533 This driver also works for the following NE2000 clone cards:
1534 RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2
1535 NetVin NV5000SC Via 86C926 SureCom NE34 Winbond
1536 Holtek HT80232 Holtek HT80229
1537
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001538 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001539 will be called ne2k-pci.
1540
1541config NE3210
1542 tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
1543 depends on NET_PCI && EISA && EXPERIMENTAL
1544 select CRC32
1545 ---help---
1546 If you have a network (Ethernet) card of this type, say Y and read
1547 the Ethernet-HOWTO, available from
1548 <http://www.tldp.org/docs.html#howto>. Note that this driver
1549 will NOT WORK for NE3200 cards as they are completely different.
1550
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001551 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001552 will be called ne3210.
1553
1554config ES3210
1555 tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
1556 depends on NET_PCI && EISA && EXPERIMENTAL
1557 select CRC32
1558 help
1559 If you have a network (Ethernet) card of this type, say Y and read
1560 the Ethernet-HOWTO, available from
1561 <http://www.tldp.org/docs.html#howto>.
1562
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001563 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001564 will be called es3210.
1565
1566config 8139CP
1567 tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
1568 depends on NET_PCI && PCI && EXPERIMENTAL
1569 select CRC32
1570 select MII
1571 help
1572 This is a driver for the Fast Ethernet PCI network cards based on
1573 the RTL8139C+ chips. If you have one of those, say Y and read
1574 the Ethernet-HOWTO, available from
1575 <http://www.tldp.org/docs.html#howto>.
1576
1577 To compile this driver as a module, choose M here: the module
1578 will be called 8139cp. This is recommended.
1579
1580config 8139TOO
Adrian Bunkf04e3f02005-05-16 21:13:03 +02001581 tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001582 depends on NET_PCI && PCI
1583 select CRC32
1584 select MII
1585 ---help---
1586 This is a driver for the Fast Ethernet PCI network cards based on
Adrian Bunkf04e3f02005-05-16 21:13:03 +02001587 the RTL 8129/8130/8139 chips. If you have one of those, say Y and
1588 read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001589
1590 To compile this driver as a module, choose M here: the module
1591 will be called 8139too. This is recommended.
1592
1593config 8139TOO_PIO
1594 bool "Use PIO instead of MMIO"
1595 default y
1596 depends on 8139TOO
1597 help
1598 This instructs the driver to use programmed I/O ports (PIO) instead
1599 of PCI shared memory (MMIO). This can possibly solve some problems
1600 in case your mainboard has memory consistency issues. If unsure,
1601 say N.
1602
1603config 8139TOO_TUNE_TWISTER
1604 bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
1605 depends on 8139TOO
1606 help
1607 This implements a function which might come in handy in case you
1608 are using low quality on long cabling. It is required for RealTek
1609 RTL-8139 revision K boards, and totally unused otherwise. It tries
1610 to match the transceiver to the cable characteristics. This is
1611 experimental since hardly documented by the manufacturer.
1612 If unsure, say Y.
1613
1614config 8139TOO_8129
1615 bool "Support for older RTL-8129/8130 boards"
1616 depends on 8139TOO
1617 help
1618 This enables support for the older and uncommon RTL-8129 and
1619 RTL-8130 chips, which support MII via an external transceiver,
1620 instead of an internal one. Disabling this option will save some
1621 memory by making the code size smaller. If unsure, say Y.
1622
1623config 8139_OLD_RX_RESET
1624 bool "Use older RX-reset method"
1625 depends on 8139TOO
1626 help
1627 The 8139too driver was recently updated to contain a more rapid
1628 reset sequence, in the face of severe receive errors. This "new"
1629 RX-reset method should be adequate for all boards. But if you
1630 experience problems, you can enable this option to restore the
1631 old RX-reset behavior. If unsure, say N.
1632
Sten Wang7a47dd72007-11-12 21:31:11 -08001633config R6040
Florian Fainelli68334112009-01-08 15:04:50 +00001634 tristate "RDC R6040 Fast Ethernet Adapter support"
Sten Wang7a47dd72007-11-12 21:31:11 -08001635 depends on NET_PCI && PCI
1636 select CRC32
1637 select MII
1638 help
1639 This is a driver for the R6040 Fast Ethernet MACs found in the
1640 the RDC R-321x System-on-chips.
1641
1642 To compile this driver as a module, choose M here: the module
1643 will be called r6040. This is recommended.
1644
Linus Torvalds1da177e2005-04-16 15:20:36 -07001645config SIS900
1646 tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
1647 depends on NET_PCI && PCI
1648 select CRC32
Adrian Bunk6da0f682005-04-30 13:52:49 +02001649 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07001650 ---help---
1651 This is a driver for the Fast Ethernet PCI network cards based on
1652 the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
Adrian Bunkc3cf5602006-03-04 17:07:57 +01001653 SiS 630 and SiS 540 chipsets.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001654
1655 This driver also supports AMD 79C901 HomePNA so that you can use
1656 your phone line as a network cable.
1657
1658 To compile this driver as a module, choose M here: the module
1659 will be called sis900. This is recommended.
1660
1661config EPIC100
1662 tristate "SMC EtherPower II"
1663 depends on NET_PCI && PCI
1664 select CRC32
1665 select MII
1666 help
1667 This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
1668 which is based on the SMC83c17x (EPIC/100).
1669 More specific information and updates are available from
1670 <http://www.scyld.com/network/epic100.html>.
1671
Steve Glendinning2cb37722008-12-11 20:54:30 -08001672config SMSC9420
1673 tristate "SMSC LAN9420 PCI ethernet adapter support"
1674 depends on NET_PCI && PCI
1675 select CRC32
1676 select PHYLIB
1677 select SMSC_PHY
1678 help
1679 This is a driver for SMSC's LAN9420 PCI ethernet adapter.
1680 Say Y if you want it compiled into the kernel,
1681 and read the Ethernet-HOWTO, available from
1682 <http://www.linuxdoc.org/docs.html#howto>.
1683
1684 This driver is also available as a module. The module will be
1685 called smsc9420. If you want to compile it as a module, say M
1686 here and read <file:Documentation/kbuild/modules.txt>
1687
Linus Torvalds1da177e2005-04-16 15:20:36 -07001688config SUNDANCE
1689 tristate "Sundance Alta support"
1690 depends on NET_PCI && PCI
1691 select CRC32
1692 select MII
1693 help
1694 This driver is for the Sundance "Alta" chip.
1695 More specific information and updates are available from
1696 <http://www.scyld.com/network/sundance.html>.
1697
1698config SUNDANCE_MMIO
1699 bool "Use MMIO instead of PIO"
1700 depends on SUNDANCE
1701 help
1702 Enable memory-mapped I/O for interaction with Sundance NIC registers.
1703 Do NOT enable this by default, PIO (enabled when MMIO is disabled)
1704 is known to solve bugs on certain chips.
1705
1706 If unsure, say N.
1707
1708config TLAN
1709 tristate "TI ThunderLAN support"
Stephen Hemminger93e16842008-05-30 09:49:55 -07001710 depends on NET_PCI && (PCI || EISA)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001711 ---help---
1712 If you have a PCI Ethernet network card based on the ThunderLAN chip
1713 which is supported by this driver, say Y and read the
1714 Ethernet-HOWTO, available from
1715 <http://www.tldp.org/docs.html#howto>.
1716
1717 Devices currently supported by this driver are Compaq Netelligent,
1718 Compaq NetFlex and Olicom cards. Please read the file
1719 <file:Documentation/networking/tlan.txt> for more details.
1720
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001721 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001722 will be called tlan.
1723
1724 Please email feedback to <torben.mathiasen@compaq.com>.
1725
Richard Ršöjforsb07878e2009-06-04 03:35:55 +00001726config KS8842
1727 tristate "Micrel KSZ8842"
Heiko Carstens0cf08dc2009-06-22 21:32:18 +00001728 depends on HAS_IOMEM
Richard Ršöjforsb07878e2009-06-04 03:35:55 +00001729 help
Andreas Mohrc1893082009-08-21 00:46:06 +00001730 This platform driver is for Micrel KSZ8842 / KS8842
1731 2-port ethernet switch chip (managed, VLAN, QoS).
Richard Ršöjforsb07878e2009-06-04 03:35:55 +00001732
Ben Dooks3ba81f32009-07-16 05:24:08 +00001733config KS8851
1734 tristate "Micrel KS8851 SPI"
1735 depends on SPI
Alexander Beregalovde72e5d2009-07-22 01:16:51 +00001736 select MII
Randy Dunlapcbb35f8a2009-08-19 12:13:31 -07001737 select CRC32
Ben Dooks3ba81f32009-07-16 05:24:08 +00001738 help
1739 SPI driver for Micrel KS8851 SPI attached network chip.
1740
Choi, Davida55c0a0e2009-09-25 14:42:12 +00001741config KS8851_MLL
1742 tristate "Micrel KS8851 MLL"
1743 depends on HAS_IOMEM
Randy Dunlap47a01a02009-10-14 15:10:58 -07001744 select MII
Choi, Davida55c0a0e2009-09-25 14:42:12 +00001745 help
1746 This platform driver is for Micrel KS8851 Address/data bus
1747 multiplexed network chip.
1748
Linus Torvalds1da177e2005-04-16 15:20:36 -07001749config VIA_RHINE
1750 tristate "VIA Rhine support"
1751 depends on NET_PCI && PCI
1752 select CRC32
1753 select MII
1754 help
1755 If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
1756 Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
1757 Ethernet functions can also be found integrated on South Bridges
1758 (e.g. VT8235).
1759
1760 To compile this driver as a module, choose M here. The module
1761 will be called via-rhine.
1762
1763config VIA_RHINE_MMIO
1764 bool "Use MMIO instead of PIO"
1765 depends on VIA_RHINE
1766 help
1767 This instructs the driver to use PCI shared memory (MMIO) instead of
1768 programmed I/O ports (PIO). Enabling this gives an improvement in
1769 processing time in parts of the driver.
1770
1771 If unsure, say Y.
1772
Cesar Eduardo Barrosbf345702006-12-19 13:08:47 -08001773config SC92031
1774 tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
1775 depends on NET_PCI && PCI && EXPERIMENTAL
1776 select CRC32
1777 ---help---
1778 This is a driver for the Fast Ethernet PCI network cards based on
1779 the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
1780 have one of these, say Y here.
1781
1782 To compile this driver as a module, choose M here: the module
1783 will be called sc92031. This is recommended.
1784
Matteo Croced95b39c2007-10-14 18:10:13 +02001785config CPMAC
1786 tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
Florian Fainelli839b04c2009-08-04 11:17:49 +00001787 depends on NET_ETHERNET && EXPERIMENTAL && AR7
Matteo Croced95b39c2007-10-14 18:10:13 +02001788 select PHYLIB
Matteo Croced95b39c2007-10-14 18:10:13 +02001789 help
1790 TI AR7 CPMAC Ethernet support
1791
Linus Torvalds1da177e2005-04-16 15:20:36 -07001792config NET_POCKET
1793 bool "Pocket and portable adapters"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001794 depends on PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001795 ---help---
1796 Cute little network (Ethernet) devices which attach to the parallel
1797 port ("pocket adapters"), commonly used with laptops. If you have
1798 one of those, say Y and read the Ethernet-HOWTO, available from
1799 <http://www.tldp.org/docs.html#howto>.
1800
1801 If you want to plug a network (or some other) card into the PCMCIA
1802 (or PC-card) slot of your laptop instead (PCMCIA is the standard for
1803 credit card size extension cards used by all modern laptops), you
1804 need the pcmcia-cs package (location contained in the file
1805 <file:Documentation/Changes>) and you can say N here.
1806
1807 Laptop users should read the Linux Laptop home page at
1808 <http://www.linux-on-laptops.com/> or
1809 Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.
1810
1811 Note that the answer to this question doesn't directly affect the
1812 kernel: saying N will just cause the configurator to skip all
1813 the questions about this class of network devices. If you say Y, you
1814 will be asked for your specific device in the following questions.
1815
1816config ATP
1817 tristate "AT-LAN-TEC/RealTek pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001818 depends on NET_POCKET && PARPORT && X86
Linus Torvalds1da177e2005-04-16 15:20:36 -07001819 select CRC32
1820 ---help---
1821 This is a network (Ethernet) device which attaches to your parallel
1822 port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
1823 available from <http://www.tldp.org/docs.html#howto>, if you
1824 want to use this. If you intend to use this driver, you should have
1825 said N to the "Parallel printer support", because the two drivers
1826 don't like each other.
1827
1828 To compile this driver as a module, choose M here: the module
1829 will be called atp.
1830
1831config DE600
1832 tristate "D-Link DE600 pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001833 depends on NET_POCKET && PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001834 ---help---
1835 This is a network (Ethernet) device which attaches to your parallel
1836 port. Read <file:Documentation/networking/DLINK.txt> as well as the
1837 Ethernet-HOWTO, available from
1838 <http://www.tldp.org/docs.html#howto>, if you want to use
1839 this. It is possible to have several devices share a single parallel
1840 port and it is safe to compile the corresponding drivers into the
1841 kernel.
1842
1843 To compile this driver as a module, choose M here: the module
1844 will be called de600.
1845
1846config DE620
1847 tristate "D-Link DE620 pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001848 depends on NET_POCKET && PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001849 ---help---
1850 This is a network (Ethernet) device which attaches to your parallel
1851 port. Read <file:Documentation/networking/DLINK.txt> as well as the
1852 Ethernet-HOWTO, available from
1853 <http://www.tldp.org/docs.html#howto>, if you want to use
1854 this. It is possible to have several devices share a single parallel
1855 port and it is safe to compile the corresponding drivers into the
1856 kernel.
1857
1858 To compile this driver as a module, choose M here: the module
1859 will be called de620.
1860
1861config SGISEEQ
1862 tristate "SGI Seeq ethernet controller support"
Thomas Bogendoerfer49b11bc2007-12-19 13:42:36 +01001863 depends on SGI_HAS_SEEQ
Linus Torvalds1da177e2005-04-16 15:20:36 -07001864 help
1865 Say Y here if you have an Seeq based Ethernet network card. This is
1866 used in many Silicon Graphics machines.
1867
1868config DECLANCE
1869 tristate "DEC LANCE ethernet controller support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001870 depends on MACH_DECSTATION
Linus Torvalds1da177e2005-04-16 15:20:36 -07001871 select CRC32
1872 help
1873 This driver is for the series of Ethernet controllers produced by
1874 DEC (now Compaq) based on the AMD Lance chipset, including the
1875 DEPCA series. (This chipset is better known via the NE2100 cards.)
1876
1877config 68360_ENET
1878 bool "Motorola 68360 ethernet controller"
1879 depends on M68360
1880 help
1881 Say Y here if you want to use the built-in ethernet controller of
1882 the Motorola 68360 processor.
1883
1884config FEC
Fabio Estevam64423302009-05-27 03:41:39 +00001885 bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
Fabio Estevamfcd195c2009-09-21 14:41:21 +00001886 depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
Linus Torvalds1da177e2005-04-16 15:20:36 -07001887 help
1888 Say Y here if you want to use the built-in 10/100 Fast ethernet
Sascha Hauer196719e2009-01-28 23:03:10 +00001889 controller on some Motorola ColdFire and Freescale i.MX processors.
Greg Ungerer2af69212005-09-12 11:18:10 +10001890
1891config FEC2
1892 bool "Second FEC ethernet controller (on some ColdFire CPUs)"
1893 depends on FEC
1894 help
1895 Say Y here if you want to use the second built-in 10/100 Fast
1896 ethernet controller on some Motorola ColdFire processors.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001897
Domen Puncer5d031e92007-10-26 18:07:49 +02001898config FEC_MPC52xx
1899 tristate "MPC52xx FEC driver"
Grant Likely847cdf42008-11-14 05:19:00 -07001900 depends on PPC_MPC52xx && PPC_BESTCOMM
Domen Puncer5d031e92007-10-26 18:07:49 +02001901 select CRC32
1902 select PHYLIB
Grant Likely847cdf42008-11-14 05:19:00 -07001903 select PPC_BESTCOMM_FEC
Domen Puncer5d031e92007-10-26 18:07:49 +02001904 ---help---
1905 This option enables support for the MPC5200's on-chip
1906 Fast Ethernet Controller
Pavel Machek4737f092009-06-05 00:44:53 +02001907 If compiled as module, it will be called fec_mpc52xx.
Domen Puncer5d031e92007-10-26 18:07:49 +02001908
1909config FEC_MPC52xx_MDIO
1910 bool "MPC52xx FEC MDIO bus driver"
1911 depends on FEC_MPC52xx
1912 default y
1913 ---help---
1914 The MPC5200's FEC can connect to the Ethernet either with
1915 an external MII PHY chip or 10 Mbps 7-wire interface
1916 (Motorola? industry standard).
1917 If your board uses an external PHY connected to FEC, enable this.
1918 If not sure, enable.
Pavel Machek4737f092009-06-05 00:44:53 +02001919 If compiled as module, it will be called fec_mpc52xx_phy.
Domen Puncer5d031e92007-10-26 18:07:49 +02001920
Linus Torvalds1da177e2005-04-16 15:20:36 -07001921config NE_H8300
1922 tristate "NE2000 compatible support for H8/300"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001923 depends on H8300
Linus Torvalds1da177e2005-04-16 15:20:36 -07001924 help
1925 Say Y here if you want to use the NE2000 compatible
1926 controller on the Renesas H8/300 processor.
1927
Chris Snook452c1ce2008-09-14 19:56:10 -05001928config ATL2
1929 tristate "Atheros L2 Fast Ethernet support"
1930 depends on PCI
1931 select CRC32
1932 select MII
1933 help
1934 This driver supports the Atheros L2 fast ethernet adapter.
1935
1936 To compile this driver as a module, choose M here. The module
1937 will be called atl2.
1938
John Linnbb81b2d2009-08-20 02:52:16 -07001939config XILINX_EMACLITE
1940 tristate "Xilinx 10/100 Ethernet Lite support"
1941 depends on PPC32 || MICROBLAZE
1942 help
1943 This driver supports the 10/100 Ethernet Lite from Xilinx.
1944
Maxime Bizon9b1fc552009-08-18 13:23:40 +01001945config BCM63XX_ENET
1946 tristate "Broadcom 63xx internal mac support"
1947 depends on BCM63XX
1948 select MII
1949 select PHYLIB
1950 help
1951 This driver supports the ethernet MACs in the Broadcom 63xx
1952 MIPS chipset family (BCM63XX).
1953
Pantelis Antoniou48257c42005-10-28 16:25:58 -04001954source "drivers/net/fs_enet/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001955
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001956endif # NET_ETHERNET
Linus Torvalds1da177e2005-04-16 15:20:36 -07001957
1958#
1959# Gigabit Ethernet
1960#
1961
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001962menuconfig NETDEV_1000
1963 bool "Ethernet (1000 Mbit)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07001964 depends on !UML
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001965 default y
Jan Engelhardt06bfb7e2007-08-18 12:56:21 +02001966 ---help---
1967 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
1968 type of Local Area Network (LAN) in universities and companies.
1969
1970 Say Y here to get to see options for Gigabit Ethernet drivers.
1971 This option alone does not add any kernel code.
1972 Note that drivers supporting both 100 and 1000 MBit may be listed
1973 under "Ethernet (10 or 100MBit)" instead.
1974
1975 If you say N, all options in this submenu will be skipped and disabled.
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001976
1977if NETDEV_1000
Linus Torvalds1da177e2005-04-16 15:20:36 -07001978
1979config ACENIC
1980 tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
1981 depends on PCI
1982 ---help---
1983 Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
1984 GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
1985 adapter. The driver allows for using the Jumbo Frame option (9000
1986 bytes/frame) however it requires that your switches can handle this
1987 as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
1988 line.
1989
1990 To compile this driver as a module, choose M here: the
1991 module will be called acenic.
1992
1993config ACENIC_OMIT_TIGON_I
1994 bool "Omit support for old Tigon I based AceNICs"
1995 depends on ACENIC
1996 help
1997 Say Y here if you only have Tigon II based AceNICs and want to leave
1998 out support for the older Tigon I based cards which are no longer
1999 being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
2000 version)). This will reduce the size of the driver object by
2001 app. 100KB. If you are not sure whether your card is a Tigon I or a
2002 Tigon II, say N here.
2003
2004 The safe and default value for this is N.
2005
2006config DL2K
Komurodf950822007-08-13 09:45:41 +09002007 tristate "DL2000/TC902x-based Gigabit Ethernet support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002008 depends on PCI
2009 select CRC32
2010 help
Komurodf950822007-08-13 09:45:41 +09002011 This driver supports DL2000/TC902x-based Gigabit ethernet cards,
2012 which includes
Linus Torvalds1da177e2005-04-16 15:20:36 -07002013 D-Link DGE-550T Gigabit Ethernet Adapter.
2014 D-Link DL2000-based Gigabit Ethernet Adapter.
Komurodf950822007-08-13 09:45:41 +09002015 Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002016
2017 To compile this driver as a module, choose M here: the
2018 module will be called dl2k.
2019
2020config E1000
2021 tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
2022 depends on PCI
2023 ---help---
2024 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
2025 adapters. For more information on how to identify your adapter, go
2026 to the Adapter & Driver ID Guide at:
2027
2028 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2029
2030 For general information and support, go to the Intel support
2031 website at:
2032
2033 <http://support.intel.com>
2034
2035 More specific information on configuring the driver is in
2036 <file:Documentation/networking/e1000.txt>.
2037
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002038 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07002039 will be called e1000.
2040
Auke Kokbc7f75f2007-09-17 12:30:59 -07002041config E1000E
2042 tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
Al Viro7ac86bf2008-04-27 06:15:42 +01002043 depends on PCI && (!SPARC32 || BROKEN)
Auke Kokbc7f75f2007-09-17 12:30:59 -07002044 ---help---
2045 This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
2046 ethernet family of adapters. For PCI or PCI-X e1000 adapters,
2047 use the regular e1000 driver For more information on how to
2048 identify your adapter, go to the Adapter & Driver ID Guide at:
2049
2050 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2051
2052 For general information and support, go to the Intel support
2053 website at:
2054
2055 <http://support.intel.com>
2056
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002057 To compile this driver as a module, choose M here. The module
Auke Kokbc7f75f2007-09-17 12:30:59 -07002058 will be called e1000e.
2059
Stephen Hemmingerab7a9832008-01-01 09:27:58 -08002060config IP1000
2061 tristate "IP1000 Gigabit Ethernet support"
2062 depends on PCI && EXPERIMENTAL
2063 select MII
2064 ---help---
2065 This driver supports IP1000 gigabit Ethernet cards.
2066
2067 To compile this driver as a module, choose M here: the module
2068 will be called ipg. This is recommended.
2069
Auke Kok9d5c8242008-01-24 02:22:38 -08002070config IGB
Alexander Duyck3ef6b232008-11-20 00:46:57 -08002071 tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support"
Auke Kok9d5c8242008-01-24 02:22:38 -08002072 depends on PCI
2073 ---help---
Alexander Duyck3ef6b232008-11-20 00:46:57 -08002074 This driver supports Intel(R) 82575/82576 gigabit ethernet family of
Auke Kok9d5c8242008-01-24 02:22:38 -08002075 adapters. For more information on how to identify your adapter, go
2076 to the Adapter & Driver ID Guide at:
2077
2078 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2079
2080 For general information and support, go to the Intel support
2081 website at:
2082
2083 <http://support.intel.com>
2084
2085 More specific information on configuring the driver is in
2086 <file:Documentation/networking/e1000.txt>.
2087
Johann Felix Soden2bfc79d2008-02-05 03:13:58 -08002088 To compile this driver as a module, choose M here. The module
Auke Kok9d5c8242008-01-24 02:22:38 -08002089 will be called igb.
2090
Jeff Kirsher421e02f2008-10-17 11:08:31 -07002091config IGB_DCA
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002092 bool "Direct Cache Access (DCA) Support"
Jeff Kirsher421e02f2008-10-17 11:08:31 -07002093 default y
2094 depends on IGB && DCA && !(IGB=y && DCA=m)
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002095 ---help---
2096 Say Y here if you want to use Direct Cache Access (DCA) in the
2097 driver. DCA is a method for warming the CPU cache before data
2098 is used, with the intent of lessening the impact of cache misses.
Jeff Kirsher421e02f2008-10-17 11:08:31 -07002099
Alexander Duyckd4e0fe02009-04-07 14:37:34 +00002100config IGBVF
2101 tristate "Intel(R) 82576 Virtual Function Ethernet support"
2102 depends on PCI
2103 ---help---
2104 This driver supports Intel(R) 82576 virtual functions. For more
2105 information on how to identify your adapter, go to the Adapter &
2106 Driver ID Guide at:
2107
2108 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2109
2110 For general information and support, go to the Intel support
2111 website at:
2112
2113 <http://support.intel.com>
2114
2115 More specific information on configuring the driver is in
2116 <file:Documentation/networking/e1000.txt>.
2117
2118 To compile this driver as a module, choose M here. The module
2119 will be called igbvf.
2120
Lennert Buytenhek15d014d2005-11-11 18:23:13 +01002121source "drivers/net/ixp2000/Kconfig"
2122
Linus Torvalds1da177e2005-04-16 15:20:36 -07002123config MYRI_SBUS
2124 tristate "MyriCOM Gigabit Ethernet support"
2125 depends on SBUS
2126 help
2127 This driver supports MyriCOM Sbus gigabit Ethernet cards.
2128
2129 To compile this driver as a module, choose M here: the module
2130 will be called myri_sbus. This is recommended.
2131
2132config NS83820
Jon Mason47c51432006-02-12 11:53:04 -06002133 tristate "National Semiconductor DP83820 support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002134 depends on PCI
2135 help
2136 This is a driver for the National Semiconductor DP83820 series
2137 of gigabit ethernet MACs. Cards using this chipset include
2138 the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
2139 SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of
2140 zero copy.
2141
2142config HAMACHI
2143 tristate "Packet Engines Hamachi GNIC-II support"
2144 depends on PCI
2145 select MII
2146 help
2147 If you have a Gigabit Ethernet card of this type, say Y and read
2148 the Ethernet-HOWTO, available from
2149 <http://www.tldp.org/docs.html#howto>.
2150
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002151 To compile this driver as a module, choose M here. The module will be
Linus Torvalds1da177e2005-04-16 15:20:36 -07002152 called hamachi.
2153
2154config YELLOWFIN
2155 tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
2156 depends on PCI && EXPERIMENTAL
2157 select CRC32
2158 ---help---
2159 Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
2160 adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
2161 used by the Beowulf Linux cluster project. See
2162 <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
2163 information about this driver in particular and Beowulf in general.
2164
2165 To compile this driver as a module, choose M here: the module
2166 will be called yellowfin. This is recommended.
2167
2168config R8169
2169 tristate "Realtek 8169 gigabit ethernet support"
2170 depends on PCI
2171 select CRC32
Francois Romieub7372492008-09-13 15:04:38 +02002172 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07002173 ---help---
2174 Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
2175
2176 To compile this driver as a module, choose M here: the module
2177 will be called r8169. This is recommended.
2178
Linus Torvalds1da177e2005-04-16 15:20:36 -07002179config R8169_VLAN
2180 bool "VLAN support"
2181 depends on R8169 && VLAN_8021Q
2182 ---help---
2183 Say Y here for the r8169 driver to support the functions required
2184 by the kernel 802.1Q code.
Francois Romieu865c6522008-05-11 14:51:00 +02002185
Linus Torvalds1da177e2005-04-16 15:20:36 -07002186 If in doubt, say Y.
2187
Maciej W. Rozycki1a9e8542007-09-14 12:05:00 +01002188config SB1250_MAC
Maciej W. Rozycki25a72df2007-09-14 11:57:33 +01002189 tristate "SB1250 Gigabit Ethernet support"
2190 depends on SIBYTE_SB1xxx_SOC
Maciej W. Rozyckif5279ff2007-09-21 12:52:10 +01002191 select PHYLIB
Maciej W. Rozycki25a72df2007-09-14 11:57:33 +01002192 ---help---
2193 This driver supports Gigabit Ethernet interfaces based on the
2194 Broadcom SiByte family of System-On-a-Chip parts. They include
2195 the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
2196 and BCM1480 chips.
2197
2198 To compile this driver as a module, choose M here: the module
2199 will be called sb1250-mac.
2200
Francois Romieu890e8d02005-07-30 13:08:43 +02002201config SIS190
Francois Romieue7976372005-09-03 00:57:51 +02002202 tristate "SiS190/SiS191 gigabit ethernet support"
Adrian Bunke9985d52005-08-09 02:41:00 +02002203 depends on PCI
2204 select CRC32
2205 select MII
2206 ---help---
Francois Romieue7976372005-09-03 00:57:51 +02002207 Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
2208 a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
2209 appear in lan on motherboard designs which are based on SiS 965
2210 and SiS 966 south bridge.
Francois Romieu890e8d02005-07-30 13:08:43 +02002211
Adrian Bunke9985d52005-08-09 02:41:00 +02002212 To compile this driver as a module, choose M here: the module
2213 will be called sis190. This is recommended.
Francois Romieu890e8d02005-07-30 13:08:43 +02002214
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002215config SKGE
Stephen Hemminger7a160c72006-02-13 15:48:08 -08002216 tristate "New SysKonnect GigaEthernet support"
2217 depends on PCI
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002218 select CRC32
2219 ---help---
2220 This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
2221 and related Gigabit Ethernet adapters. It is a new smaller driver
Stephen Hemminger46a60f22005-09-09 12:54:56 -07002222 with better performance and more complete ethtool support.
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002223
2224 It does not support the link failover and network management
Stephen Hemminger5ad887f2007-09-15 19:35:14 -04002225 features that "portable" vendor supplied sk98lin driver does.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002226
Daniel Drakec6f0d752006-01-21 19:35:34 +00002227 This driver supports adapters based on the original Yukon chipset:
2228 Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
2229 Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
2230
2231 It does not support the newer Yukon2 chipset: a separate driver,
2232 sky2, is provided for Yukon2-based adapters.
2233
2234 To compile this driver as a module, choose M here: the module
2235 will be called skge. This is recommended.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002236
Stephen Hemminger678aa1f2007-10-16 12:15:54 -07002237config SKGE_DEBUG
2238 bool "Debugging interface"
2239 depends on SKGE && DEBUG_FS
2240 help
2241 This option adds the ability to dump driver state for debugging.
GeunSik Lim156f5a72009-06-02 15:01:37 +09002242 The file /sys/kernel/debug/skge/ethX displays the state of the internal
Stephen Hemminger678aa1f2007-10-16 12:15:54 -07002243 transmit and receive rings.
2244
2245 If unsure, say N.
2246
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002247config SKY2
Stephen Hemminger8a3e3bf2007-07-09 15:33:38 -07002248 tristate "SysKonnect Yukon2 support"
Stephen Hemmingerf479b322006-10-27 10:22:10 -07002249 depends on PCI
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002250 select CRC32
2251 ---help---
Matt LaPlantecab00892006-10-03 22:36:44 +02002252 This driver supports Gigabit Ethernet adapters based on the
Daniel Drakec6f0d752006-01-21 19:35:34 +00002253 Marvell Yukon 2 chipset:
2254 Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
2255 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
2256
Stephen Hemmingerf479b322006-10-27 10:22:10 -07002257 There is companion driver for the older Marvell Yukon and
2258 Genesis based adapters: skge.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002259
2260 To compile this driver as a module, choose M here: the module
2261 will be called sky2. This is recommended.
2262
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002263config SKY2_DEBUG
2264 bool "Debugging interface"
2265 depends on SKY2 && DEBUG_FS
2266 help
2267 This option adds the ability to dump driver state for debugging.
GeunSik Lim156f5a72009-06-02 15:01:37 +09002268 The file /sys/kernel/debug/sky2/ethX displays the state of the internal
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002269 transmit and receive rings.
Daniel Drakec6f0d752006-01-21 19:35:34 +00002270
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002271 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002272
2273config VIA_VELOCITY
2274 tristate "VIA Velocity support"
Yoichi Yuasa73815532007-05-24 16:12:27 +09002275 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07002276 select CRC32
2277 select CRC_CCITT
2278 select MII
2279 help
2280 If you have a VIA "Velocity" based network card say Y here.
2281
2282 To compile this driver as a module, choose M here. The module
2283 will be called via-velocity.
2284
2285config TIGON3
2286 tristate "Broadcom Tigon3 support"
2287 depends on PCI
Matt Carlson158d7ab2008-05-29 01:37:54 -07002288 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -07002289 help
2290 This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
2291
2292 To compile this driver as a module, choose M here: the module
2293 will be called tg3. This is recommended.
2294
Michael Chanb6016b72005-05-26 13:03:09 -07002295config BNX2
2296 tristate "Broadcom NetXtremeII support"
2297 depends on PCI
Michael Chanfba9fe92006-06-12 22:21:25 -07002298 select CRC32
Michael Chan57579f72009-04-04 16:51:14 -07002299 select FW_LOADER
Michael Chanb6016b72005-05-26 13:03:09 -07002300 help
2301 This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
2302
2303 To compile this driver as a module, choose M here: the module
2304 will be called bnx2. This is recommended.
2305
Michael Chana4636962009-06-08 18:14:43 -07002306config CNIC
2307 tristate "Broadcom CNIC support"
Michael Chanbabdb782009-06-10 13:35:28 -07002308 depends on PCI
2309 select BNX2
2310 select UIO
Michael Chana4636962009-06-08 18:14:43 -07002311 help
2312 This driver supports offload features of Broadcom NetXtremeII
2313 gigabit Ethernet cards.
2314
2315 To compile this driver as a module, choose M here: the module
2316 will be called cnic. This is recommended.
2317
Jens Osterkampaaec0fa2005-09-05 15:19:29 -07002318config SPIDER_NET
2319 tristate "Spider Gigabit Ethernet driver"
Kou Ishizaki3342cf0e2007-02-20 16:36:14 -06002320 depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
Christoph Hellwig9b158792006-03-15 11:30:44 +01002321 select FW_LOADER
Jens Osterkampaaec0fa2005-09-05 15:19:29 -07002322 help
2323 This driver supports the Gigabit Ethernet chips present on the
2324 Cell Processor-Based Blades from IBM.
2325
Zang Roy-r619115e123b82006-11-08 19:49:13 -08002326config TSI108_ETH
2327 tristate "Tundra TSI108 gigabit Ethernet support"
2328 depends on TSI108_BRIDGE
2329 help
2330 This driver supports Tundra TSI108 gigabit Ethernet ports.
2331 To compile this driver as a module, choose M here: the module
2332 will be called tsi108_eth.
2333
Masakazu Mokuno02c18892007-07-05 20:11:16 +09002334config GELIC_NET
2335 tristate "PS3 Gigabit Ethernet driver"
2336 depends on PPC_PS3
Geoff Levand1d32e212008-04-10 07:01:53 +10002337 select PS3_SYS_MANAGER
Masakazu Mokuno02c18892007-07-05 20:11:16 +09002338 help
2339 This driver supports the network device on the PS3 game
2340 console. This driver has built-in support for Ethernet.
2341
2342 To compile this driver as a module, choose M here: the
2343 module will be called ps3_gelic.
2344
Masakazu Mokuno09dde542008-02-07 19:58:57 +09002345config GELIC_WIRELESS
John W. Linville97ed8392008-03-06 13:08:09 -05002346 bool "PS3 Wireless support"
2347 depends on GELIC_NET
2348 select WIRELESS_EXT
2349 help
2350 This option adds the support for the wireless feature of PS3.
2351 If you have the wireless-less model of PS3 or have no plan to
2352 use wireless feature, disabling this option saves memory. As
2353 the driver automatically distinguishes the models, you can
2354 safely enable this option even if you have a wireless-less model.
Masakazu Mokuno09dde542008-02-07 19:58:57 +09002355
Masakazu Mokunof409e342008-05-30 16:52:55 +09002356config GELIC_WIRELESS_OLD_PSK_INTERFACE
2357 bool "PS3 Wireless private PSK interface (OBSOLETE)"
2358 depends on GELIC_WIRELESS
2359 help
2360 This option retains the obsolete private interface to pass
2361 the PSK from user space programs to the driver. The PSK
2362 stands for 'Pre Shared Key' and is used for WPA[2]-PSK
2363 (WPA-Personal) environment.
2364 If WPA[2]-PSK is used and you need to use old programs that
2365 support only this old interface, say Y. Otherwise N.
2366
2367 If unsure, say N.
2368
Andy Fleming1577ece2009-02-04 16:42:12 -08002369config FSL_PQ_MDIO
2370 tristate "Freescale PQ MDIO"
2371 depends on FSL_SOC
2372 select PHYLIB
2373 help
2374 This driver supports the MDIO bus used by the gianfar and UCC drivers.
2375
Linus Torvalds1da177e2005-04-16 15:20:36 -07002376config GIANFAR
2377 tristate "Gianfar Ethernet"
Kumar Gala3a831562008-01-28 10:24:30 -06002378 depends on FSL_SOC
Andy Fleming1577ece2009-02-04 16:42:12 -08002379 select FSL_PQ_MDIO
Andy Flemingbb40dcb2005-09-23 22:54:21 -04002380 select PHYLIB
Dave Jiangbf41a7c2007-04-12 10:57:06 -07002381 select CRC32
Linus Torvalds1da177e2005-04-16 15:20:36 -07002382 help
Jon Loeligeref82a3062006-06-17 17:52:55 -05002383 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
2384 and MPC86xx family of chips, and the FEC on the 8540.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002385
Li Yangce973b12006-08-14 23:00:11 -07002386config UCC_GETH
Timur Tabi7d776cb2007-03-12 15:40:27 -05002387 tristate "Freescale QE Gigabit Ethernet"
2388 depends on QUICC_ENGINE
Andy Fleming1577ece2009-02-04 16:42:12 -08002389 select FSL_PQ_MDIO
Jan Altenberg296baae2007-06-01 00:46:29 -07002390 select PHYLIB
Li Yangce973b12006-08-14 23:00:11 -07002391 help
Timur Tabi7d776cb2007-03-12 15:40:27 -05002392 This driver supports the Gigabit Ethernet mode of the QUICC Engine,
2393 which is available on some Freescale SOCs.
Li Yangce973b12006-08-14 23:00:11 -07002394
Michael Reissd5b90492007-04-13 01:26:19 -05002395config UGETH_TX_ON_DEMAND
2396 bool "Transmit on Demand support"
Li Yangce973b12006-08-14 23:00:11 -07002397 depends on UCC_GETH
2398
Linus Torvalds1da177e2005-04-16 15:20:36 -07002399config MV643XX_ETH
Lennert Buytenhek9c1bbdf2007-10-19 04:11:03 +02002400 tristate "Marvell Discovery (643XX) and Orion ethernet support"
Gabriel Paubertdfa92642009-05-25 22:46:19 -07002401 depends on MV64X60 || PPC32 || PLAT_ORION
Lennert Buytenhekab307a32009-02-24 15:41:32 +00002402 select INET_LRO
Lennert Buytenheked944932008-08-26 13:34:19 +02002403 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -07002404 help
Lennert Buytenhek9c1bbdf2007-10-19 04:11:03 +02002405 This driver supports the gigabit ethernet MACs in the
2406 Marvell Discovery PPC/MIPS chipset family (MV643XX) and
2407 in the Marvell Orion ARM SoC family.
2408
2409 Some boards that use the Discovery chipset are the Momenco
2410 Ocelot C and Jaguar ATX and Pegasos II.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002411
Grant Likely92744982009-04-25 12:53:39 +00002412config XILINX_LL_TEMAC
2413 tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
2414 select PHYLIB
2415 depends on PPC_DCR_NATIVE
2416 help
2417 This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
2418 core used in Xilinx Spartan and Virtex FPGAs
2419
Ron Mercer5a4faa872006-07-25 00:40:21 -07002420config QLA3XXX
2421 tristate "QLogic QLA3XXX Network Driver Support"
2422 depends on PCI
2423 help
2424 This driver supports QLogic ISP3XXX gigabit Ethernet cards.
2425
2426 To compile this driver as a module, choose M here: the module
2427 will be called qla3xxx.
2428
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002429config ATL1
Jay Cliburna6d1f362008-09-27 04:17:22 +00002430 tristate "Atheros/Attansic L1 Gigabit Ethernet support"
2431 depends on PCI
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002432 select CRC32
2433 select MII
2434 help
Jay Cliburna6d1f362008-09-27 04:17:22 +00002435 This driver supports the Atheros/Attansic L1 gigabit ethernet
2436 adapter.
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002437
2438 To compile this driver as a module, choose M here. The module
2439 will be called atl1.
2440
Jie Yanga6a53252008-07-18 11:37:13 +08002441config ATL1E
2442 tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
2443 depends on PCI && EXPERIMENTAL
2444 select CRC32
2445 select MII
2446 help
2447 This driver supports the Atheros L1E gigabit ethernet adapter.
2448
2449 To compile this driver as a module, choose M here. The module
2450 will be called atl1e.
2451
Jie Yang43250dd2009-02-18 17:24:15 -08002452config ATL1C
2453 tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
2454 depends on PCI && EXPERIMENTAL
2455 select CRC32
2456 select MII
2457 help
2458 This driver supports the Atheros L1C gigabit ethernet adapter.
2459
2460 To compile this driver as a module, choose M here. The module
2461 will be called atl1c.
2462
Guo-Fu Tseng95252232008-09-16 01:00:11 +08002463config JME
2464 tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
2465 depends on PCI
2466 select CRC32
2467 select MII
2468 ---help---
2469 This driver supports the PCI-Express gigabit ethernet adapters
2470 based on JMicron JMC250 chipset.
2471
2472 To compile this driver as a module, choose M here. The module
2473 will be called jme.
2474
Oskar Schirmer8b0215a2009-06-10 12:58:48 -07002475config S6GMAC
2476 tristate "S6105 GMAC ethernet support"
2477 depends on XTENSA_VARIANT_S6000
2478 select PHYLIB
2479 help
2480 This driver supports the on chip ethernet device on the
2481 S6105 xtensa processor.
2482
2483 To compile this driver as a module, choose M here. The module
2484 will be called s6gmac.
2485
Giuseppe Cavallaro47dd7a52009-10-14 15:13:45 -07002486source "drivers/net/stmmac/Kconfig"
2487
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002488endif # NETDEV_1000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002489
2490#
2491# 10 Gigabit Ethernet
2492#
2493
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002494menuconfig NETDEV_10000
2495 bool "Ethernet (10000 Mbit)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002496 depends on !UML
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002497 default y
Jan Engelhardt06bfb7e2007-08-18 12:56:21 +02002498 ---help---
2499 Say Y here to get to see options for 10 Gigabit Ethernet drivers.
2500 This option alone does not add any kernel code.
2501
2502 If you say N, all options in this submenu will be skipped and disabled.
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002503
2504if NETDEV_10000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002505
Ben Hutchings1b1c2e92009-04-29 08:04:46 +00002506config MDIO
2507 tristate
2508
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002509config CHELSIO_T1
2510 tristate "Chelsio 10Gb Ethernet support"
2511 depends on PCI
Stephen Hemminger57834ca2006-12-01 16:36:19 -08002512 select CRC32
Ben Hutchings23c33202009-04-29 08:06:34 +00002513 select MDIO
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002514 help
Stephen Hemmingerf1d3d382006-12-01 16:36:16 -08002515 This driver supports Chelsio gigabit and 10-gigabit
2516 Ethernet cards. More information about adapter features and
2517 performance tuning is in <file:Documentation/networking/cxgb.txt>.
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002518
2519 For general information about Chelsio and our products, visit
2520 our website at <http://www.chelsio.com>.
2521
2522 For customer support, please visit our customer support page at
2523 <http://www.chelsio.com/support.htm>.
2524
2525 Please send feedback to <linux-bugs@chelsio.com>.
2526
2527 To compile this driver as a module, choose M here: the module
2528 will be called cxgb.
2529
Stephen Hemminger352c4172006-12-01 16:36:17 -08002530config CHELSIO_T1_1G
2531 bool "Chelsio gigabit Ethernet support"
2532 depends on CHELSIO_T1
2533 help
2534 Enables support for Chelsio's gigabit Ethernet PCI cards. If you
2535 are using only 10G cards say 'N' here.
2536
James Bottomley58daa682008-12-30 10:20:24 -06002537config CHELSIO_T3_DEPENDS
2538 tristate
2539 depends on PCI && INET
2540 default y
2541
Divy Le Ray4d22de32007-01-18 22:04:14 -05002542config CHELSIO_T3
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002543 tristate "Chelsio Communications T3 10Gb Ethernet support"
James Bottomley58daa682008-12-30 10:20:24 -06002544 depends on CHELSIO_T3_DEPENDS
Divy Le Ray2e283962007-03-18 13:10:06 -07002545 select FW_LOADER
Ben Hutchings0f07c4e2009-04-29 08:07:20 +00002546 select MDIO
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002547 help
2548 This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
2549 adapters.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002550
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002551 For general information about Chelsio and our products, visit
2552 our website at <http://www.chelsio.com>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002553
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002554 For customer support, please visit our customer support page at
2555 <http://www.chelsio.com/support.htm>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002556
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002557 Please send feedback to <linux-bugs@chelsio.com>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002558
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002559 To compile this driver as a module, choose M here: the module
2560 will be called cxgb3.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002561
Jan-Bernd Themann7a291082006-09-13 17:44:31 +02002562config EHEA
2563 tristate "eHEA Ethernet support"
Nathan Lynch60d50192008-06-04 08:31:28 +10002564 depends on IBMEBUS && INET && SPARSEMEM
Jan-Bernd Themannd4dc4ec2007-09-25 16:16:34 -07002565 select INET_LRO
Jan-Bernd Themann7a291082006-09-13 17:44:31 +02002566 ---help---
2567 This driver supports the IBM pSeries eHEA ethernet adapter.
2568
2569 To compile the driver as a module, choose M here. The module
2570 will be called ehea.
2571
Scott Feldman01f2e4e2008-09-15 09:17:11 -07002572config ENIC
Roland Dreiereb8a4cb2008-10-13 18:53:05 -07002573 tristate "Cisco 10G Ethernet NIC support"
Scott Feldman01f2e4e2008-09-15 09:17:11 -07002574 depends on PCI && INET
2575 select INET_LRO
2576 help
2577 This enables the support for the Cisco 10G Ethernet card.
2578
Auke Kok9a799d72007-09-15 14:07:45 -07002579config IXGBE
2580 tristate "Intel(R) 10GbE PCI Express adapters support"
Mallikarjuna R Chilakala177db6f2008-06-18 15:32:19 -07002581 depends on PCI && INET
Ben Hutchings6b73e102009-04-29 08:08:58 +00002582 select MDIO
Auke Kok9a799d72007-09-15 14:07:45 -07002583 ---help---
2584 This driver supports Intel(R) 10GbE PCI Express family of
2585 adapters. For more information on how to identify your adapter, go
2586 to the Adapter & Driver ID Guide at:
2587
2588 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2589
2590 For general information and support, go to the Intel support
2591 website at:
2592
2593 <http://support.intel.com>
2594
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002595 To compile this driver as a module, choose M here. The module
Auke Kok9a799d72007-09-15 14:07:45 -07002596 will be called ixgbe.
2597
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002598config IXGBE_DCA
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002599 bool "Direct Cache Access (DCA) Support"
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002600 default y
2601 depends on IXGBE && DCA && !(IXGBE=y && DCA=m)
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002602 ---help---
2603 Say Y here if you want to use Direct Cache Access (DCA) in the
2604 driver. DCA is a method for warming the CPU cache before data
2605 is used, with the intent of lessening the impact of cache misses.
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002606
Jeff Kirsher7a6b6f52008-11-25 01:02:08 -08002607config IXGBE_DCB
Alexander Duyck2f90b862008-11-20 20:52:10 -08002608 bool "Data Center Bridging (DCB) Support"
2609 default n
Jeff Kirsher7a6b6f52008-11-25 01:02:08 -08002610 depends on IXGBE && DCB
Alexander Duyck2f90b862008-11-20 20:52:10 -08002611 ---help---
2612 Say Y here if you want to use Data Center Bridging (DCB) in the
2613 driver.
2614
2615 If unsure, say N.
2616
Linus Torvalds1da177e2005-04-16 15:20:36 -07002617config IXGB
2618 tristate "Intel(R) PRO/10GbE support"
2619 depends on PCI
2620 ---help---
Auke Kok9a799d72007-09-15 14:07:45 -07002621 This driver supports Intel(R) PRO/10GbE family of adapters for
2622 PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
2623 instead. For more information on how to identify your adapter, go
Linus Torvalds1da177e2005-04-16 15:20:36 -07002624 to the Adapter & Driver ID Guide at:
2625
2626 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2627
2628 For general information and support, go to the Intel support
2629 website at:
2630
2631 <http://support.intel.com>
2632
2633 More specific information on configuring the driver is in
2634 <file:Documentation/networking/ixgb.txt>.
2635
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002636 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07002637 will be called ixgb.
2638
Linus Torvalds1da177e2005-04-16 15:20:36 -07002639config S2IO
2640 tristate "S2IO 10Gbe XFrame NIC"
2641 depends on PCI
2642 ---help---
2643 This driver supports the 10Gbe XFrame NIC of S2IO.
Akinobu Mita9eb343a2005-10-21 19:06:42 +09002644 More specific information on configuring the driver is in
2645 <file:Documentation/networking/s2io.txt>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002646
Ramkrishna Vepaf1782852009-04-01 18:15:24 +00002647config VXGE
2648 tristate "Neterion X3100 Series 10GbE PCIe Server Adapter"
2649 depends on PCI && INET
2650 ---help---
2651 This driver supports Neterion Inc's X3100 Series 10 GbE PCIe
2652 I/O Virtualized Server Adapter.
2653 More specific information on configuring the driver is in
2654 <file:Documentation/networking/vxge.txt>.
2655
2656config VXGE_DEBUG_TRACE_ALL
2657 bool "Enabling All Debug trace statments in driver"
2658 default n
2659 depends on VXGE
2660 ---help---
2661 Say Y here if you want to enabling all the debug trace statements in
2662 driver. By default only few debug trace statements are enabled.
2663
Brice Goglin0da34b62006-05-23 06:10:15 -04002664config MYRI10GE
2665 tristate "Myricom Myri-10G Ethernet support"
Randy Dunlape0d5dab2007-10-18 21:53:50 -07002666 depends on PCI && INET
Brice Goglin0da34b62006-05-23 06:10:15 -04002667 select FW_LOADER
2668 select CRC32
Andrew Gallatin1e6e9342007-09-17 11:37:42 -07002669 select INET_LRO
Brice Goglin0da34b62006-05-23 06:10:15 -04002670 ---help---
2671 This driver supports Myricom Myri-10G Dual Protocol interface in
2672 Ethernet mode. If the eeprom on your board is not recent enough,
2673 you will need a newer firmware image.
2674 You may get this image or more information, at:
2675
Brice Goglind2794902006-09-05 21:58:50 -04002676 <http://www.myri.com/scs/download-Myri10GE.html>
Brice Goglin0da34b62006-05-23 06:10:15 -04002677
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002678 To compile this driver as a module, choose M here. The module
Brice Goglin0da34b62006-05-23 06:10:15 -04002679 will be called myri10ge.
2680
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002681config MYRI10GE_DCA
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002682 bool "Direct Cache Access (DCA) Support"
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002683 default y
2684 depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002685 ---help---
2686 Say Y here if you want to use Direct Cache Access (DCA) in the
2687 driver. DCA is a method for warming the CPU cache before data
2688 is used, with the intent of lessening the impact of cache misses.
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002689
Amit S. Kale3d396eb2006-10-21 15:33:03 -04002690config NETXEN_NIC
2691 tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
Randy Dunlap5ac36612006-11-16 21:39:11 -08002692 depends on PCI
Amit S. Kale3d396eb2006-10-21 15:33:03 -04002693 help
2694 This enables the support for NetXen's Gigabit Ethernet card.
2695
David S. Millera3138df2007-10-09 01:54:01 -07002696config NIU
2697 tristate "Sun Neptune 10Gbit Ethernet support"
2698 depends on PCI
Randy Dunlapc557c152009-12-10 13:50:56 -08002699 select CRC32
David S. Millera3138df2007-10-09 01:54:01 -07002700 help
2701 This enables support for cards based upon Sun's
2702 Neptune chipset.
2703
Olof Johanssonf5cd7872007-01-31 21:43:54 -06002704config PASEMI_MAC
2705 tristate "PA Semi 1/10Gbit MAC"
Michael Ellerman5beaf7d2008-03-28 12:17:33 +11002706 depends on PPC_PASEMI && PCI
Olof Johanssonbb6e9592007-05-08 00:47:54 -05002707 select PHYLIB
Olof Johansson28ae79f2007-11-28 20:57:27 -06002708 select INET_LRO
Olof Johanssonf5cd7872007-01-31 21:43:54 -06002709 help
2710 This driver supports the on-chip 1/10Gbit Ethernet controller on
2711 PA Semi's PWRficient line of chips.
2712
Yevgeny Petrilinc27a02c2008-10-22 15:47:49 -07002713config MLX4_EN
2714 tristate "Mellanox Technologies 10Gbit Ethernet support"
2715 depends on PCI && INET
2716 select MLX4_CORE
2717 select INET_LRO
2718 help
2719 This driver supports Mellanox Technologies ConnectX Ethernet
2720 devices.
2721
Roland Dreier225c7b12007-05-08 18:00:38 -07002722config MLX4_CORE
2723 tristate
2724 depends on PCI
2725 default n
2726
2727config MLX4_DEBUG
2728 bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
Paul Mundtf550d942007-05-10 12:50:28 +09002729 depends on MLX4_CORE
Roland Dreier225c7b12007-05-08 18:00:38 -07002730 default y
2731 ---help---
2732 This option causes debugging code to be compiled into the
2733 mlx4_core driver. The output can be turned on via the
2734 debug_level module parameter (which can also be set after
2735 the driver is loaded through sysfs).
2736
Andy Gospodarek1a348cc2007-09-17 18:50:36 -07002737config TEHUTI
2738 tristate "Tehuti Networks 10G Ethernet"
2739 depends on PCI
2740 help
2741 Tehuti Networks 10G Ethernet NIC
2742
Eliezer Tamira2fbb9e2007-11-15 20:09:02 +02002743config BNX2X
2744 tristate "Broadcom NetXtremeII 10Gb support"
2745 depends on PCI
Vladislav Zolotarov94a78b72009-04-27 03:27:43 -07002746 select FW_LOADER
Lee Schermerhorn07b270e2007-12-13 16:02:59 -08002747 select ZLIB_INFLATE
Eilon Greenstein34f80b02008-06-23 20:33:01 -07002748 select LIBCRC32C
Eilon Greenstein01cd4522009-08-12 08:23:08 +00002749 select MDIO
Eliezer Tamira2fbb9e2007-11-15 20:09:02 +02002750 help
2751 This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
2752 To compile this driver as a module, choose M here: the module
2753 will be called bnx2x. This is recommended.
2754
Ron Mercerc4e84bd2008-09-18 11:56:28 -04002755config QLGE
2756 tristate "QLogic QLGE 10Gb Ethernet Driver Support"
2757 depends on PCI
2758 help
2759 This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
2760
2761 To compile this driver as a module, choose M here: the module
2762 will be called qlge.
2763
Ben Hutchings8ceee662008-04-27 12:55:59 +01002764source "drivers/net/sfc/Kconfig"
Eliezer Tamira2fbb9e2007-11-15 20:09:02 +02002765
Sathya Perla6b7c5b92009-03-11 23:32:03 -07002766source "drivers/net/benet/Kconfig"
2767
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002768endif # NETDEV_10000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002769
Linus Torvalds1da177e2005-04-16 15:20:36 -07002770source "drivers/net/tokenring/Kconfig"
2771
2772source "drivers/net/wireless/Kconfig"
2773
Inaky Perez-Gonzalez143ee2d2008-12-23 16:18:48 -08002774source "drivers/net/wimax/Kconfig"
2775
Jeff Garzik5b2fc492007-05-09 21:31:55 -04002776source "drivers/net/usb/Kconfig"
2777
Linus Torvalds1da177e2005-04-16 15:20:36 -07002778source "drivers/net/pcmcia/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002779
2780source "drivers/net/wan/Kconfig"
2781
2782source "drivers/atm/Kconfig"
2783
Sergey Lapin84594642009-06-08 12:18:51 +00002784source "drivers/ieee802154/Kconfig"
2785
Linus Torvalds1da177e2005-04-16 15:20:36 -07002786source "drivers/s390/net/Kconfig"
2787
Jeremy Fitzhardinge0d160212007-07-17 18:37:06 -07002788config XEN_NETDEV_FRONTEND
2789 tristate "Xen network device frontend driver"
2790 depends on XEN
2791 default y
2792 help
2793 The network device frontend driver allows the kernel to
2794 access network devices exported exported by a virtual
2795 machine containing a physical network device driver. The
2796 frontend driver is intended for unprivileged guest domains;
2797 if you are compiling a kernel for a Xen guest, you almost
2798 certainly want to enable this.
2799
Linus Torvalds1da177e2005-04-16 15:20:36 -07002800config ISERIES_VETH
2801 tristate "iSeries Virtual Ethernet driver support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002802 depends on PPC_ISERIES
Linus Torvalds1da177e2005-04-16 15:20:36 -07002803
Matt Porterf89efd52005-09-09 12:10:10 -07002804config RIONET
2805 tristate "RapidIO Ethernet over messaging driver support"
Randy Dunlapa81c52a2006-11-01 21:18:58 -08002806 depends on RAPIDIO
Matt Porterf89efd52005-09-09 12:10:10 -07002807
2808config RIONET_TX_SIZE
2809 int "Number of outbound queue entries"
2810 depends on RIONET
2811 default "128"
2812
2813config RIONET_RX_SIZE
2814 int "Number of inbound queue entries"
2815 depends on RIONET
2816 default "128"
2817
Linus Torvalds1da177e2005-04-16 15:20:36 -07002818config FDDI
Dave Joneseb560922008-12-27 20:43:48 -08002819 tristate "FDDI driver support"
Maciej W. Rozyckie89a2cf2007-02-05 16:28:27 -08002820 depends on (PCI || EISA || TC)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002821 help
2822 Fiber Distributed Data Interface is a high speed local area network
2823 design; essentially a replacement for high speed Ethernet. FDDI can
2824 run over copper or fiber. If you are connected to such a network and
2825 want a driver for the FDDI card in your computer, say Y here (and
2826 then also Y to the driver for your FDDI card, below). Most people
2827 will say N.
2828
2829config DEFXX
Maciej W. Rozyckie89a2cf2007-02-05 16:28:27 -08002830 tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
2831 depends on FDDI && (PCI || EISA || TC)
2832 ---help---
2833 This is support for the DIGITAL series of TURBOchannel (DEFTA),
2834 EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
2835 to a local FDDI network.
2836
2837 To compile this driver as a module, choose M here: the module
2838 will be called defxx. If unsure, say N.
2839
2840config DEFXX_MMIO
2841 bool
2842 prompt "Use MMIO instead of PIO" if PCI || EISA
2843 depends on DEFXX
2844 default n if PCI || EISA
2845 default y
2846 ---help---
2847 This instructs the driver to use EISA or PCI memory-mapped I/O
2848 (MMIO) as appropriate instead of programmed I/O ports (PIO).
2849 Enabling this gives an improvement in processing time in parts
2850 of the driver, but it may cause problems with EISA (DEFEA)
2851 adapters. TURBOchannel does not have the concept of I/O ports,
2852 so MMIO is always used for these (DEFTA) adapters.
2853
2854 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002855
2856config SKFP
2857 tristate "SysKonnect FDDI PCI support"
2858 depends on FDDI && PCI
Akinobu Mitabc63eb92006-12-19 13:09:08 -08002859 select BITREVERSE
Linus Torvalds1da177e2005-04-16 15:20:36 -07002860 ---help---
2861 Say Y here if you have a SysKonnect FDDI PCI adapter.
2862 The following adapters are supported by this driver:
2863 - SK-5521 (SK-NET FDDI-UP)
2864 - SK-5522 (SK-NET FDDI-UP DAS)
2865 - SK-5541 (SK-NET FDDI-FP)
2866 - SK-5543 (SK-NET FDDI-LP)
2867 - SK-5544 (SK-NET FDDI-LP DAS)
2868 - SK-5821 (SK-NET FDDI-UP64)
2869 - SK-5822 (SK-NET FDDI-UP64 DAS)
2870 - SK-5841 (SK-NET FDDI-FP64)
2871 - SK-5843 (SK-NET FDDI-LP64)
2872 - SK-5844 (SK-NET FDDI-LP64 DAS)
2873 - Netelligent 100 FDDI DAS Fibre SC
2874 - Netelligent 100 FDDI SAS Fibre SC
2875 - Netelligent 100 FDDI DAS UTP
2876 - Netelligent 100 FDDI SAS UTP
2877 - Netelligent 100 FDDI SAS Fibre MIC
2878
2879 Read <file:Documentation/networking/skfp.txt> for information about
2880 the driver.
2881
2882 Questions concerning this driver can be addressed to:
2883 <linux@syskonnect.de>
2884
2885 To compile this driver as a module, choose M here: the module
2886 will be called skfp. This is recommended.
2887
2888config HIPPI
2889 bool "HIPPI driver support (EXPERIMENTAL)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002890 depends on EXPERIMENTAL && INET && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07002891 help
2892 HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
2893 1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
2894 can run over copper (25m) or fiber (300m on multi-mode or 10km on
2895 single-mode). HIPPI networks are commonly used for clusters and to
2896 connect to super computers. If you are connected to a HIPPI network
2897 and have a HIPPI network card in your computer that you want to use
2898 under Linux, say Y here (you must also remember to enable the driver
2899 for your HIPPI card below). Most people will say N here.
2900
2901config ROADRUNNER
2902 tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
2903 depends on HIPPI && PCI
2904 help
2905 Say Y here if this is your PCI HIPPI network card.
2906
2907 To compile this driver as a module, choose M here: the module
2908 will be called rrunner. If unsure, say N.
2909
2910config ROADRUNNER_LARGE_RINGS
2911 bool "Use large TX/RX rings (EXPERIMENTAL)"
2912 depends on ROADRUNNER
2913 help
2914 If you say Y here, the RoadRunner driver will preallocate up to 2 MB
2915 of additional memory to allow for fastest operation, both for
2916 transmitting and receiving. This memory cannot be used by any other
2917 kernel code or by user space programs. Say Y here only if you have
2918 the memory.
2919
2920config PLIP
2921 tristate "PLIP (parallel port) support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002922 depends on PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07002923 ---help---
2924 PLIP (Parallel Line Internet Protocol) is used to create a
2925 reasonably fast mini network consisting of two (or, rarely, more)
2926 local machines. A PLIP link from a Linux box is a popular means to
2927 install a Linux distribution on a machine which doesn't have a
2928 CD-ROM drive (a minimal system has to be transferred with floppies
2929 first). The kernels on both machines need to have this PLIP option
2930 enabled for this to work.
2931
2932 The PLIP driver has two modes, mode 0 and mode 1. The parallel
2933 ports (the connectors at the computers with 25 holes) are connected
2934 with "null printer" or "Turbo Laplink" cables which can transmit 4
2935 bits at a time (mode 0) or with special PLIP cables, to be used on
2936 bidirectional parallel ports only, which can transmit 8 bits at a
2937 time (mode 1); you can find the wiring of these cables in
2938 <file:Documentation/networking/PLIP.txt>. The cables can be up to
2939 15m long. Mode 0 works also if one of the machines runs DOS/Windows
2940 and has some PLIP software installed, e.g. the Crynwr PLIP packet
2941 driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
2942 and winsock or NCSA's telnet.
2943
2944 If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
2945 as the NET-3-HOWTO, both available from
2946 <http://www.tldp.org/docs.html#howto>. Note that the PLIP
2947 protocol has been changed and this PLIP driver won't work together
2948 with the PLIP support in Linux versions 1.0.x. This option enlarges
2949 your kernel by about 8 KB.
2950
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002951 To compile this driver as a module, choose M here. The module
2952 will be called plip. If unsure, say Y or M, in case you buy
2953 a laptop later.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002954
2955config PPP
2956 tristate "PPP (point-to-point protocol) support"
Ralf Baechleb6e37e52006-07-14 12:15:40 +01002957 select SLHC
Linus Torvalds1da177e2005-04-16 15:20:36 -07002958 ---help---
2959 PPP (Point to Point Protocol) is a newer and better SLIP. It serves
2960 the same purpose: sending Internet traffic over telephone (and other
2961 serial) lines. Ask your access provider if they support it, because
2962 otherwise you can't use it; most Internet access providers these
2963 days support PPP rather than SLIP.
2964
2965 To use PPP, you need an additional program called pppd as described
2966 in the PPP-HOWTO, available at
2967 <http://www.tldp.org/docs.html#howto>. Make sure that you have
2968 the version of pppd recommended in <file:Documentation/Changes>.
2969 The PPP option enlarges your kernel by about 16 KB.
2970
2971 There are actually two versions of PPP: the traditional PPP for
2972 asynchronous lines, such as regular analog phone lines, and
2973 synchronous PPP which can be used over digital ISDN lines for
2974 example. If you want to use PPP over phone lines or other
2975 asynchronous serial lines, you need to say Y (or M) here and also to
2976 the next option, "PPP support for async serial ports". For PPP over
2977 synchronous lines, you should say Y (or M) here and to "Support
2978 synchronous PPP", below.
2979
2980 If you said Y to "Version information on all symbols" above, then
2981 you cannot compile the PPP driver into the kernel; you can then only
2982 compile it as a module. To compile this driver as a module, choose M
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002983 here. The module will be called ppp_generic.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002984
2985config PPP_MULTILINK
2986 bool "PPP multilink support (EXPERIMENTAL)"
2987 depends on PPP && EXPERIMENTAL
2988 help
2989 PPP multilink is a protocol (defined in RFC 1990) which allows you
2990 to combine several (logical or physical) lines into one logical PPP
2991 connection, so that you can utilize your full bandwidth.
2992
2993 This has to be supported at the other end as well and you need a
2994 version of the pppd daemon which understands the multilink protocol.
2995
2996 If unsure, say N.
2997
2998config PPP_FILTER
2999 bool "PPP filtering"
3000 depends on PPP
3001 help
3002 Say Y here if you want to be able to filter the packets passing over
3003 PPP interfaces. This allows you to control which packets count as
3004 activity (i.e. which packets will reset the idle timer or bring up
Jon Mason47c51432006-02-12 11:53:04 -06003005 a demand-dialed link) and which packets are to be dropped entirely.
Linus Torvalds1da177e2005-04-16 15:20:36 -07003006 You need to say Y here if you wish to use the pass-filter and
3007 active-filter options to pppd.
3008
3009 If unsure, say N.
3010
3011config PPP_ASYNC
3012 tristate "PPP support for async serial ports"
3013 depends on PPP
3014 select CRC_CCITT
3015 ---help---
3016 Say Y (or M) here if you want to be able to use PPP over standard
3017 asynchronous serial ports, such as COM1 or COM2 on a PC. If you use
3018 a modem (not a synchronous or ISDN modem) to contact your ISP, you
3019 need this option.
3020
3021 To compile this driver as a module, choose M here.
3022
3023 If unsure, say Y.
3024
3025config PPP_SYNC_TTY
3026 tristate "PPP support for sync tty ports"
3027 depends on PPP
3028 help
3029 Say Y (or M) here if you want to be able to use PPP over synchronous
3030 (HDLC) tty devices, such as the SyncLink adapter. These devices
3031 are often used for high-speed leased lines like T1/E1.
3032
3033 To compile this driver as a module, choose M here.
3034
3035config PPP_DEFLATE
3036 tristate "PPP Deflate compression"
3037 depends on PPP
3038 select ZLIB_INFLATE
3039 select ZLIB_DEFLATE
3040 ---help---
3041 Support for the Deflate compression method for PPP, which uses the
3042 Deflate algorithm (the same algorithm that gzip uses) to compress
3043 each PPP packet before it is sent over the wire. The machine at the
3044 other end of the PPP link (usually your ISP) has to support the
3045 Deflate compression method as well for this to be useful. Even if
3046 they don't support it, it is safe to say Y here.
3047
3048 To compile this driver as a module, choose M here.
3049
3050config PPP_BSDCOMP
3051 tristate "PPP BSD-Compress compression"
3052 depends on PPP
3053 ---help---
3054 Support for the BSD-Compress compression method for PPP, which uses
3055 the LZW compression method to compress each PPP packet before it is
3056 sent over the wire. The machine at the other end of the PPP link
3057 (usually your ISP) has to support the BSD-Compress compression
3058 method as well for this to be useful. Even if they don't support it,
3059 it is safe to say Y here.
3060
3061 The PPP Deflate compression method ("PPP Deflate compression",
3062 above) is preferable to BSD-Compress, because it compresses better
3063 and is patent-free.
3064
3065 Note that the BSD compression code will always be compiled as a
3066 module; it is called bsd_comp and will show up in the directory
3067 modules once you have said "make modules". If unsure, say N.
3068
Matt Domschb3f9b922005-11-08 09:40:47 -08003069config PPP_MPPE
3070 tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
3071 depends on PPP && EXPERIMENTAL
3072 select CRYPTO
3073 select CRYPTO_SHA1
3074 select CRYPTO_ARC4
Patrick McHardybcbaecb2006-10-25 16:49:36 +10003075 select CRYPTO_ECB
Matt Domschb3f9b922005-11-08 09:40:47 -08003076 ---help---
3077 Support for the MPPE Encryption protocol, as employed by the
3078 Microsoft Point-to-Point Tunneling Protocol.
3079
3080 See http://pptpclient.sourceforge.net/ for information on
3081 configuring PPTP clients and servers to utilize this method.
3082
Linus Torvalds1da177e2005-04-16 15:20:36 -07003083config PPPOE
3084 tristate "PPP over Ethernet (EXPERIMENTAL)"
3085 depends on EXPERIMENTAL && PPP
3086 help
3087 Support for PPP over Ethernet.
3088
3089 This driver requires the latest version of pppd from the CVS
3090 repository at cvs.samba.org. Alternatively, see the
3091 RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
3092 which contains instruction on how to use this driver (under
3093 the heading "Kernel mode PPPoE").
3094
3095config PPPOATM
3096 tristate "PPP over ATM"
3097 depends on ATM && PPP
3098 help
3099 Support PPP (Point to Point Protocol) encapsulated in ATM frames.
3100 This implementation does not yet comply with section 8 of RFC2364,
3101 which can lead to bad results if the ATM peer loses state and
3102 changes its encapsulation unilaterally.
3103
James Chapman3557baa2007-06-27 15:49:24 -07003104config PPPOL2TP
3105 tristate "PPP over L2TP (EXPERIMENTAL)"
James Chapman143cf352007-07-30 18:51:48 -07003106 depends on EXPERIMENTAL && PPP && INET
James Chapman3557baa2007-06-27 15:49:24 -07003107 help
3108 Support for PPP-over-L2TP socket family. L2TP is a protocol
3109 used by ISPs and enterprises to tunnel PPP traffic over UDP
3110 tunnels. L2TP is replacing PPTP for VPN uses.
3111
3112 This kernel component handles only L2TP data packets: a
3113 userland daemon handles L2TP the control protocol (tunnel
3114 and session setup). One such daemon is OpenL2TP
3115 (http://openl2tp.sourceforge.net/).
3116
Linus Torvalds1da177e2005-04-16 15:20:36 -07003117config SLIP
3118 tristate "SLIP (serial line) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07003119 ---help---
3120 Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
3121 connect to your Internet service provider or to connect to some
3122 other local Unix box or if you want to configure your Linux box as a
3123 Slip/CSlip server for other people to dial in. SLIP (Serial Line
3124 Internet Protocol) is a protocol used to send Internet traffic over
3125 serial connections such as telephone lines or null modem cables;
3126 nowadays, the protocol PPP is more commonly used for this same
3127 purpose.
3128
3129 Normally, your access provider has to support SLIP in order for you
3130 to be able to use it, but there is now a SLIP emulator called SLiRP
3131 around (available from
3132 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
3133 allows you to use SLIP over a regular dial up shell connection. If
3134 you plan to use SLiRP, make sure to say Y to CSLIP, below. The
3135 NET-3-HOWTO, available from
3136 <http://www.tldp.org/docs.html#howto>, explains how to
3137 configure SLIP. Note that you don't need this option if you just
3138 want to run term (term is a program which gives you almost full
3139 Internet connectivity if you have a regular dial up shell account on
3140 some Internet connected Unix computer. Read
3141 <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
3142 support will enlarge your kernel by about 4 KB. If unsure, say N.
3143
Adrian Bunk57ce45d2007-11-12 21:03:58 -08003144 To compile this driver as a module, choose M here. The module
3145 will be called slip.
Linus Torvalds1da177e2005-04-16 15:20:36 -07003146
3147config SLIP_COMPRESSED
3148 bool "CSLIP compressed headers"
3149 depends on SLIP
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003150 select SLHC
Linus Torvalds1da177e2005-04-16 15:20:36 -07003151 ---help---
3152 This protocol is faster than SLIP because it uses compression on the
3153 TCP/IP headers (not on the data itself), but it has to be supported
3154 on both ends. Ask your access provider if you are not sure and
3155 answer Y, just in case. You will still be able to use plain SLIP. If
3156 you plan to use SLiRP, the SLIP emulator (available from
3157 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
3158 allows you to use SLIP over a regular dial up shell connection, you
3159 definitely want to say Y here. The NET-3-HOWTO, available from
3160 <http://www.tldp.org/docs.html#howto>, explains how to configure
3161 CSLIP. This won't enlarge your kernel.
3162
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003163config SLHC
3164 tristate
3165 help
3166 This option enables Van Jacobsen serial line header compression
3167 routines.
3168
Linus Torvalds1da177e2005-04-16 15:20:36 -07003169config SLIP_SMART
3170 bool "Keepalive and linefill"
3171 depends on SLIP
3172 help
3173 Adds additional capabilities to the SLIP driver to support the
3174 RELCOM line fill and keepalive monitoring. Ideal on poor quality
3175 analogue lines.
3176
3177config SLIP_MODE_SLIP6
3178 bool "Six bit SLIP encapsulation"
3179 depends on SLIP
3180 help
3181 Just occasionally you may need to run IP over hostile serial
3182 networks that don't pass all control characters or are only seven
3183 bit. Saying Y here adds an extra mode you can use with SLIP:
3184 "slip6". In this mode, SLIP will only send normal ASCII symbols over
3185 the serial device. Naturally, this has to be supported at the other
3186 end of the link as well. It's good enough, for example, to run IP
3187 over the async ports of a Camtec JNT Pad. If unsure, say N.
3188
3189config NET_FC
3190 bool "Fibre Channel driver support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07003191 depends on SCSI && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07003192 help
3193 Fibre Channel is a high speed serial protocol mainly used to connect
3194 large storage devices to the computer; it is compatible with and
3195 intended to replace SCSI.
3196
3197 If you intend to use Fibre Channel, you need to have a Fibre channel
3198 adaptor card in your computer; say Y here and to the driver for your
3199 adaptor below. You also should have said Y to "SCSI support" and
3200 "SCSI generic support".
3201
Linus Torvalds1da177e2005-04-16 15:20:36 -07003202config NETCONSOLE
3203 tristate "Network console logging support (EXPERIMENTAL)"
Matt Mackall5e43db72005-07-27 15:24:42 -07003204 depends on EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07003205 ---help---
3206 If you want to log kernel messages over the network, enable this.
3207 See <file:Documentation/networking/netconsole.txt> for details.
3208
Satyam Sharma0bcc1812007-08-10 15:35:05 -07003209config NETCONSOLE_DYNAMIC
3210 bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
3211 depends on NETCONSOLE && SYSFS && EXPERIMENTAL
3212 select CONFIGFS_FS
3213 help
3214 This option enables the ability to dynamically reconfigure target
3215 parameters (interface, IP addresses, port numbers, MAC addresses)
3216 at runtime through a userspace interface exported using configfs.
3217 See <file:Documentation/networking/netconsole.txt> for details.
3218
Randy Dunlap54208992005-07-18 13:45:12 -07003219config NETPOLL
3220 def_bool NETCONSOLE
3221
Randy Dunlap54208992005-07-18 13:45:12 -07003222config NETPOLL_TRAP
3223 bool "Netpoll traffic trapping"
3224 default n
3225 depends on NETPOLL
3226
3227config NET_POLL_CONTROLLER
3228 def_bool NETPOLL
3229
Rusty Russell296f96f2007-10-22 11:03:37 +10003230config VIRTIO_NET
3231 tristate "Virtio network driver (EXPERIMENTAL)"
3232 depends on EXPERIMENTAL && VIRTIO
3233 ---help---
Anthony Liguori0ad07ec2007-11-07 20:46:31 -06003234 This is the virtual network driver for virtio. It can be used with
3235 lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
Rusty Russell296f96f2007-10-22 11:03:37 +10003236
Shreyas Bhatewarad1a890fa2009-10-13 00:15:51 -07003237config VMXNET3
3238 tristate "VMware VMXNET3 ethernet driver"
Shreyas Bhatewara115924b2009-11-16 13:41:33 +00003239 depends on PCI && INET
Shreyas Bhatewarad1a890fa2009-10-13 00:15:51 -07003240 help
3241 This driver supports VMware's vmxnet3 virtual ethernet NIC.
3242 To compile this driver as a module, choose M here: the
3243 module will be called vmxnet3.
3244
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07003245endif # NETDEVICES