blob: c95639b5f2a06095c9c586aebe80f0e1bed9fa8a [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * linux/drivers/pcmcia/sa1100_neponset.c
3 *
4 * Neponset PCMCIA specific routines
5 */
6#include <linux/module.h>
7#include <linux/kernel.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -07008#include <linux/device.h>
9#include <linux/errno.h>
10#include <linux/init.h>
11
Russell Kinga09e64f2008-08-05 16:14:15 +010012#include <mach/hardware.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070013#include <asm/mach-types.h>
Russell Kinga09e64f2008-08-05 16:14:15 +010014#include <mach/neponset.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070015#include <asm/hardware/sa1111.h>
16
17#include "sa1111_generic.h"
18
19/*
20 * Neponset uses the Maxim MAX1600, with the following connections:
21 *
22 * MAX1600 Neponset
23 *
24 * A0VCC SA-1111 GPIO A<1>
25 * A1VCC SA-1111 GPIO A<0>
26 * A0VPP CPLD NCR A0VPP
27 * A1VPP CPLD NCR A1VPP
28 * B0VCC SA-1111 GPIO A<2>
29 * B1VCC SA-1111 GPIO A<3>
30 * B0VPP ground (slot B is CF)
31 * B1VPP ground (slot B is CF)
32 *
33 * VX VCC (5V)
34 * VY VCC3_3 (3.3V)
35 * 12INA 12V
36 * 12INB ground (slot B is CF)
37 *
38 * The MAX1600 CODE pin is tied to ground, placing the device in
39 * "Standard Intel code" mode. Refer to the Maxim data sheet for
40 * the corresponding truth table.
41 */
42
43static int
44neponset_pcmcia_configure_socket(struct soc_pcmcia_socket *skt, const socket_state_t *state)
45{
Russell King - ARM Linux701a5dc2009-03-29 19:42:44 +010046 struct sa1111_pcmcia_socket *s = to_skt(skt);
Linus Torvalds1da177e2005-04-16 15:20:36 -070047 unsigned int ncr_mask, ncr_set, pa_dwr_mask, pa_dwr_set;
48 int ret;
49
50 switch (skt->nr) {
51 case 0:
52 pa_dwr_mask = GPIO_A0 | GPIO_A1;
53 ncr_mask = NCR_A0VPP | NCR_A1VPP;
54
55 if (state->Vpp == 0)
56 ncr_set = 0;
57 else if (state->Vpp == 120)
58 ncr_set = NCR_A1VPP;
59 else if (state->Vpp == state->Vcc)
60 ncr_set = NCR_A0VPP;
61 else {
62 printk(KERN_ERR "%s(): unrecognized VPP %u\n",
Harvey Harrison2e11cb42008-05-01 04:34:54 -070063 __func__, state->Vpp);
Linus Torvalds1da177e2005-04-16 15:20:36 -070064 return -1;
65 }
66 break;
67
68 case 1:
69 pa_dwr_mask = GPIO_A2 | GPIO_A3;
70 ncr_mask = 0;
71 ncr_set = 0;
72
73 if (state->Vpp != state->Vcc && state->Vpp != 0) {
74 printk(KERN_ERR "%s(): CF slot cannot support VPP %u\n",
Harvey Harrison2e11cb42008-05-01 04:34:54 -070075 __func__, state->Vpp);
Linus Torvalds1da177e2005-04-16 15:20:36 -070076 return -1;
77 }
78 break;
79
80 default:
81 return -1;
82 }
83
84 /*
85 * pa_dwr_set is the mask for selecting Vcc on both sockets.
86 * pa_dwr_mask selects which bits (and therefore socket) we change.
87 */
88 switch (state->Vcc) {
89 default:
90 case 0: pa_dwr_set = 0; break;
91 case 33: pa_dwr_set = GPIO_A1|GPIO_A2; break;
92 case 50: pa_dwr_set = GPIO_A0|GPIO_A3; break;
93 }
94
95 ret = sa1111_pcmcia_configure_socket(skt, state);
96 if (ret == 0) {
97 unsigned long flags;
98
99 local_irq_save(flags);
100 NCR_0 = (NCR_0 & ~ncr_mask) | ncr_set;
101
102 local_irq_restore(flags);
Russell King - ARM Linux701a5dc2009-03-29 19:42:44 +0100103 sa1111_set_io(s->dev, pa_dwr_mask, pa_dwr_set);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700104 }
105
106 return 0;
107}
108
109static void neponset_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
110{
111 if (skt->nr == 0)
112 NCR_0 &= ~(NCR_A0VPP | NCR_A1VPP);
113
114 sa1111_pcmcia_socket_init(skt);
115}
116
117static struct pcmcia_low_level neponset_pcmcia_ops = {
118 .owner = THIS_MODULE,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700119 .configure_socket = neponset_pcmcia_configure_socket,
120 .socket_init = neponset_pcmcia_socket_init,
Russell King - ARM Linux701a5dc2009-03-29 19:42:44 +0100121 .first = 0,
122 .nr = 2,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700123};
124
Russell Kingb29cf622009-09-27 17:30:21 +0100125int pcmcia_neponset_init(struct sa1111_dev *sadev)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700126{
127 int ret = -ENODEV;
128
129 if (machine_is_assabet()) {
130 /*
131 * Set GPIO_A<3:0> to be outputs for the MAX1600,
132 * and switch to standby mode.
133 */
134 sa1111_set_io_dir(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0, 0);
135 sa1111_set_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
136 sa1111_set_sleep_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
Russell King - ARM Linux701a5dc2009-03-29 19:42:44 +0100137 sa11xx_drv_pcmcia_ops(&neponset_pcmcia_ops);
138 ret = sa1111_pcmcia_add(sadev, &neponset_pcmcia_ops,
139 sa11xx_drv_pcmcia_add_one);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700140 }
141
142 return ret;
143}