blob: 3b67a1b6a1972670c5c305c94b64c8677a720fb8 [file] [log] [blame]
Manuel Lauss0273b4e2009-10-04 14:55:29 +02001/*
2 * PCMCIA socket code for the MyCable XXS1500 system.
3 *
4 * Copyright (c) 2009 Manuel Lauss <manuel.lauss@gmail.com>
5 *
6 */
7
8#include <linux/delay.h>
9#include <linux/gpio.h>
10#include <linux/interrupt.h>
11#include <linux/io.h>
12#include <linux/ioport.h>
13#include <linux/mm.h>
14#include <linux/platform_device.h>
15#include <linux/pm.h>
16#include <linux/resource.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090017#include <linux/slab.h>
Manuel Lauss0273b4e2009-10-04 14:55:29 +020018#include <linux/spinlock.h>
19
Manuel Lauss0273b4e2009-10-04 14:55:29 +020020#include <pcmcia/ss.h>
21#include <pcmcia/cistpl.h>
22
23#include <asm/irq.h>
24#include <asm/system.h>
25#include <asm/mach-au1x00/au1000.h>
26
27#define MEM_MAP_SIZE 0x400000
28#define IO_MAP_SIZE 0x1000
29
30
31/*
32 * 3.3V cards only; all interfacing is done via gpios:
33 *
34 * 0/1: carddetect (00 = card present, xx = huh)
35 * 4: card irq
36 * 204: reset (high-act)
37 * 205: buffer enable (low-act)
38 * 208/209: card voltage key (00,01,10,11)
39 * 210: battwarn
40 * 211: batdead
41 * 214: power (low-act)
42 */
43#define GPIO_CDA 0
44#define GPIO_CDB 1
45#define GPIO_CARDIRQ 4
46#define GPIO_RESET 204
47#define GPIO_OUTEN 205
48#define GPIO_VSL 208
49#define GPIO_VSH 209
50#define GPIO_BATTDEAD 210
51#define GPIO_BATTWARN 211
52#define GPIO_POWER 214
53
54struct xxs1500_pcmcia_sock {
55 struct pcmcia_socket socket;
56 void *virt_io;
57
Manuel Lauss11b897c2010-02-24 17:40:21 +010058 phys_addr_t phys_io;
59 phys_addr_t phys_attr;
60 phys_addr_t phys_mem;
Manuel Lauss0273b4e2009-10-04 14:55:29 +020061
62 /* previous flags for set_socket() */
63 unsigned int old_flags;
64};
65
66#define to_xxs_socket(x) container_of(x, struct xxs1500_pcmcia_sock, socket)
67
68static irqreturn_t cdirq(int irq, void *data)
69{
70 struct xxs1500_pcmcia_sock *sock = data;
71
72 pcmcia_parse_events(&sock->socket, SS_DETECT);
73
74 return IRQ_HANDLED;
75}
76
77static int xxs1500_pcmcia_configure(struct pcmcia_socket *skt,
78 struct socket_state_t *state)
79{
80 struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
81 unsigned int changed;
82
83 /* power control */
84 switch (state->Vcc) {
85 case 0:
86 gpio_set_value(GPIO_POWER, 1); /* power off */
87 break;
88 case 33:
89 gpio_set_value(GPIO_POWER, 0); /* power on */
90 break;
91 case 50:
92 default:
93 return -EINVAL;
94 }
95
96 changed = state->flags ^ sock->old_flags;
97
98 if (changed & SS_RESET) {
99 if (state->flags & SS_RESET) {
100 gpio_set_value(GPIO_RESET, 1); /* assert reset */
101 gpio_set_value(GPIO_OUTEN, 1); /* buffers off */
102 } else {
103 gpio_set_value(GPIO_RESET, 0); /* deassert reset */
104 gpio_set_value(GPIO_OUTEN, 0); /* buffers on */
105 msleep(500);
106 }
107 }
108
109 sock->old_flags = state->flags;
110
111 return 0;
112}
113
114static int xxs1500_pcmcia_get_status(struct pcmcia_socket *skt,
115 unsigned int *value)
116{
117 unsigned int status;
118 int i;
119
120 status = 0;
121
122 /* check carddetects: GPIO[0:1] must both be low */
123 if (!gpio_get_value(GPIO_CDA) && !gpio_get_value(GPIO_CDB))
124 status |= SS_DETECT;
125
126 /* determine card voltage: GPIO[208:209] binary value */
127 i = (!!gpio_get_value(GPIO_VSL)) | ((!!gpio_get_value(GPIO_VSH)) << 1);
128
129 switch (i) {
130 case 0:
131 case 1:
132 case 2:
133 status |= SS_3VCARD; /* 3V card */
134 break;
135 case 3: /* 5V card, unsupported */
136 default:
137 status |= SS_XVCARD; /* treated as unsupported in core */
138 }
139
140 /* GPIO214: low active power switch */
141 status |= gpio_get_value(GPIO_POWER) ? 0 : SS_POWERON;
142
143 /* GPIO204: high-active reset line */
144 status |= gpio_get_value(GPIO_RESET) ? SS_RESET : SS_READY;
145
146 /* other stuff */
147 status |= gpio_get_value(GPIO_BATTDEAD) ? 0 : SS_BATDEAD;
148 status |= gpio_get_value(GPIO_BATTWARN) ? 0 : SS_BATWARN;
149
150 *value = status;
151
152 return 0;
153}
154
155static int xxs1500_pcmcia_sock_init(struct pcmcia_socket *skt)
156{
157 gpio_direction_input(GPIO_CDA);
158 gpio_direction_input(GPIO_CDB);
159 gpio_direction_input(GPIO_VSL);
160 gpio_direction_input(GPIO_VSH);
161 gpio_direction_input(GPIO_BATTDEAD);
162 gpio_direction_input(GPIO_BATTWARN);
163 gpio_direction_output(GPIO_RESET, 1); /* assert reset */
164 gpio_direction_output(GPIO_OUTEN, 1); /* disable buffers */
165 gpio_direction_output(GPIO_POWER, 1); /* power off */
166
167 return 0;
168}
169
170static int xxs1500_pcmcia_sock_suspend(struct pcmcia_socket *skt)
171{
172 return 0;
173}
174
175static int au1x00_pcmcia_set_io_map(struct pcmcia_socket *skt,
176 struct pccard_io_map *map)
177{
178 struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
179
180 map->start = (u32)sock->virt_io;
181 map->stop = map->start + IO_MAP_SIZE;
182
183 return 0;
184}
185
186static int au1x00_pcmcia_set_mem_map(struct pcmcia_socket *skt,
187 struct pccard_mem_map *map)
188{
189 struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
190
191 if (map->flags & MAP_ATTRIB)
192 map->static_start = sock->phys_attr + map->card_start;
193 else
194 map->static_start = sock->phys_mem + map->card_start;
195
196 return 0;
197}
198
199static struct pccard_operations xxs1500_pcmcia_operations = {
200 .init = xxs1500_pcmcia_sock_init,
201 .suspend = xxs1500_pcmcia_sock_suspend,
202 .get_status = xxs1500_pcmcia_get_status,
203 .set_socket = xxs1500_pcmcia_configure,
204 .set_io_map = au1x00_pcmcia_set_io_map,
205 .set_mem_map = au1x00_pcmcia_set_mem_map,
206};
207
208static int __devinit xxs1500_pcmcia_probe(struct platform_device *pdev)
209{
210 struct xxs1500_pcmcia_sock *sock;
211 struct resource *r;
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200212 int ret, irq;
213
214 sock = kzalloc(sizeof(struct xxs1500_pcmcia_sock), GFP_KERNEL);
215 if (!sock)
216 return -ENOMEM;
217
218 ret = -ENODEV;
219
Manuel Laussf25e1882010-03-01 21:40:56 +0100220 /* 36bit PCMCIA Attribute area address */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100221 r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-attr");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200222 if (!r) {
Manuel Lauss11b897c2010-02-24 17:40:21 +0100223 dev_err(&pdev->dev, "missing 'pcmcia-attr' resource!\n");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200224 goto out0;
225 }
226 sock->phys_attr = r->start;
227
Manuel Laussf25e1882010-03-01 21:40:56 +0100228 /* 36bit PCMCIA Memory area address */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100229 r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-mem");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200230 if (!r) {
Manuel Lauss11b897c2010-02-24 17:40:21 +0100231 dev_err(&pdev->dev, "missing 'pcmcia-mem' resource!\n");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200232 goto out0;
233 }
234 sock->phys_mem = r->start;
235
Manuel Laussf25e1882010-03-01 21:40:56 +0100236 /* 36bit PCMCIA IO area address */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100237 r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-io");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200238 if (!r) {
Manuel Lauss11b897c2010-02-24 17:40:21 +0100239 dev_err(&pdev->dev, "missing 'pcmcia-io' resource!\n");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200240 goto out0;
241 }
242 sock->phys_io = r->start;
243
244
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200245 /*
246 * PCMCIA client drivers use the inb/outb macros to access
247 * the IO registers. Since mips_io_port_base is added
248 * to the access address of the mips implementation of
249 * inb/outb, we need to subtract it here because we want
250 * to access the I/O or MEM address directly, without
251 * going through this "mips_io_port_base" mechanism.
252 */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100253 sock->virt_io = (void *)(ioremap(sock->phys_io, IO_MAP_SIZE) -
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200254 mips_io_port_base);
255
256 if (!sock->virt_io) {
257 dev_err(&pdev->dev, "cannot remap IO area\n");
258 ret = -ENOMEM;
259 goto out0;
260 }
261
262 sock->socket.ops = &xxs1500_pcmcia_operations;
263 sock->socket.owner = THIS_MODULE;
264 sock->socket.pci_irq = gpio_to_irq(GPIO_CARDIRQ);
265 sock->socket.features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
266 sock->socket.map_size = MEM_MAP_SIZE;
267 sock->socket.io_offset = (unsigned long)sock->virt_io;
268 sock->socket.dev.parent = &pdev->dev;
269 sock->socket.resource_ops = &pccard_static_ops;
270
271 platform_set_drvdata(pdev, sock);
272
273 /* setup carddetect irq: use one of the 2 GPIOs as an
274 * edge detector.
275 */
276 irq = gpio_to_irq(GPIO_CDA);
277 set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
278 ret = request_irq(irq, cdirq, 0, "pcmcia_carddetect", sock);
279 if (ret) {
280 dev_err(&pdev->dev, "cannot setup cd irq\n");
281 goto out1;
282 }
283
284 ret = pcmcia_register_socket(&sock->socket);
285 if (ret) {
286 dev_err(&pdev->dev, "failed to register\n");
287 goto out2;
288 }
289
290 printk(KERN_INFO "MyCable XXS1500 PCMCIA socket services\n");
291
292 return 0;
293
294out2:
295 free_irq(gpio_to_irq(GPIO_CDA), sock);
296out1:
297 iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
298out0:
299 kfree(sock);
300 return ret;
301}
302
303static int __devexit xxs1500_pcmcia_remove(struct platform_device *pdev)
304{
305 struct xxs1500_pcmcia_sock *sock = platform_get_drvdata(pdev);
306
307 pcmcia_unregister_socket(&sock->socket);
308 free_irq(gpio_to_irq(GPIO_CDA), sock);
309 iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
310 kfree(sock);
311
312 return 0;
313}
314
315static struct platform_driver xxs1500_pcmcia_socket_driver = {
316 .driver = {
317 .name = "xxs1500_pcmcia",
318 .owner = THIS_MODULE,
319 },
320 .probe = xxs1500_pcmcia_probe,
321 .remove = __devexit_p(xxs1500_pcmcia_remove),
322};
323
324int __init xxs1500_pcmcia_socket_load(void)
325{
326 return platform_driver_register(&xxs1500_pcmcia_socket_driver);
327}
328
329void __exit xxs1500_pcmcia_socket_unload(void)
330{
331 platform_driver_unregister(&xxs1500_pcmcia_socket_driver);
332}
333
334module_init(xxs1500_pcmcia_socket_load);
335module_exit(xxs1500_pcmcia_socket_unload);
336
337MODULE_LICENSE("GPL");
338MODULE_DESCRIPTION("PCMCIA Socket Services for MyCable XXS1500 systems");
339MODULE_AUTHOR("Manuel Lauss");