Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | /* |
| 2 | * IPWireless 3G UMTS TDD Modem driver (USB connected) |
| 3 | * |
| 4 | * Copyright (C) 2004 Roelf Diedericks <roelfd@inet.co.za> |
| 5 | * Copyright (C) 2004 Greg Kroah-Hartman <greg@kroah.com> |
| 6 | * |
| 7 | * This program is free software; you can redistribute it and/or modify |
| 8 | * it under the terms of the GNU General Public License as published by |
| 9 | * the Free Software Foundation; either version 2 of the License, or |
| 10 | * (at your option) any later version. |
| 11 | * |
| 12 | * All information about the device was acquired using SnoopyPro |
| 13 | * on MSFT's O/S, and examing the MSFT drivers' debug output |
| 14 | * (insanely left _on_ in the enduser version) |
| 15 | * |
| 16 | * It was written out of frustration with the IPWireless USB modem |
| 17 | * supplied by Axity3G/Sentech South Africa not supporting |
| 18 | * Linux whatsoever. |
| 19 | * |
| 20 | * Nobody provided any proprietary information that was not already |
| 21 | * available for this device. |
| 22 | * |
| 23 | * The modem adheres to the "3GPP TS 27.007 AT command set for 3G |
| 24 | * User Equipment (UE)" standard, available from |
| 25 | * http://www.3gpp.org/ftp/Specs/html-info/27007.htm |
| 26 | * |
| 27 | * The code was only tested the IPWireless handheld modem distributed |
| 28 | * in South Africa by Sentech. |
| 29 | * |
| 30 | * It may work for Woosh Inc in .nz too, as it appears they use the |
| 31 | * same kit. |
| 32 | * |
| 33 | * There is still some work to be done in terms of handling |
| 34 | * DCD, DTR, RTS, CTS which are currently faked. |
| 35 | * It's good enough for PPP at this point. It's based off all kinds of |
| 36 | * code found in usb/serial and usb/class |
| 37 | * |
| 38 | */ |
| 39 | |
| 40 | #include <linux/kernel.h> |
| 41 | #include <linux/errno.h> |
| 42 | #include <linux/init.h> |
| 43 | #include <linux/slab.h> |
| 44 | #include <linux/tty.h> |
| 45 | #include <linux/tty_flip.h> |
| 46 | #include <linux/module.h> |
| 47 | #include <linux/spinlock.h> |
| 48 | #include <linux/usb.h> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 49 | #include <asm/uaccess.h> |
| 50 | #include "usb-serial.h" |
| 51 | |
| 52 | /* |
| 53 | * Version Information |
| 54 | */ |
| 55 | #define DRIVER_VERSION "v0.3" |
| 56 | #define DRIVER_AUTHOR "Roelf Diedericks" |
| 57 | #define DRIVER_DESC "IPWireless tty driver" |
| 58 | |
| 59 | #define IPW_TTY_MAJOR 240 /* real device node major id, experimental range */ |
| 60 | #define IPW_TTY_MINORS 256 /* we support 256 devices, dunno why, it'd be insane :) */ |
| 61 | |
| 62 | #define USB_IPW_MAGIC 0x6d02 /* magic number for ipw struct */ |
| 63 | |
| 64 | |
| 65 | /* Message sizes */ |
| 66 | #define EVENT_BUFFER_SIZE 0xFF |
| 67 | #define CHAR2INT16(c1,c0) (((u32)((c1) & 0xff) << 8) + (u32)((c0) & 0xff)) |
| 68 | #define NUM_BULK_URBS 24 |
| 69 | #define NUM_CONTROL_URBS 16 |
| 70 | |
| 71 | /* vendor/product pairs that are known work with this driver*/ |
| 72 | #define IPW_VID 0x0bc3 |
| 73 | #define IPW_PID 0x0001 |
| 74 | |
| 75 | |
| 76 | /* Vendor commands: */ |
| 77 | |
| 78 | /* baud rates */ |
| 79 | enum { |
| 80 | ipw_sio_b256000 = 0x000e, |
| 81 | ipw_sio_b128000 = 0x001d, |
| 82 | ipw_sio_b115200 = 0x0020, |
| 83 | ipw_sio_b57600 = 0x0040, |
| 84 | ipw_sio_b56000 = 0x0042, |
| 85 | ipw_sio_b38400 = 0x0060, |
| 86 | ipw_sio_b19200 = 0x00c0, |
| 87 | ipw_sio_b14400 = 0x0100, |
| 88 | ipw_sio_b9600 = 0x0180, |
| 89 | ipw_sio_b4800 = 0x0300, |
| 90 | ipw_sio_b2400 = 0x0600, |
| 91 | ipw_sio_b1200 = 0x0c00, |
| 92 | ipw_sio_b600 = 0x1800 |
| 93 | }; |
| 94 | |
| 95 | /* data bits */ |
| 96 | #define ipw_dtb_7 0x700 |
| 97 | #define ipw_dtb_8 0x810 // ok so the define is misleading, I know, but forces 8,n,1 |
| 98 | // I mean, is there a point to any other setting these days? :) |
| 99 | |
| 100 | /* usb control request types : */ |
| 101 | #define IPW_SIO_RXCTL 0x00 // control bulk rx channel transmissions, value=1/0 (on/off) |
| 102 | #define IPW_SIO_SET_BAUD 0x01 // set baud, value=requested ipw_sio_bxxxx |
| 103 | #define IPW_SIO_SET_LINE 0x03 // set databits, parity. value=ipw_dtb_x |
| 104 | #define IPW_SIO_SET_PIN 0x03 // set/clear dtr/rts value=ipw_pin_xxx |
| 105 | #define IPW_SIO_POLL 0x08 // get serial port status byte, call with value=0 |
| 106 | #define IPW_SIO_INIT 0x11 // initializes ? value=0 (appears as first thing todo on open) |
| 107 | #define IPW_SIO_PURGE 0x12 // purge all transmissions?, call with value=numchar_to_purge |
| 108 | #define IPW_SIO_HANDFLOW 0x13 // set xon/xoff limits value=0, and a buffer of 0x10 bytes |
| 109 | #define IPW_SIO_SETCHARS 0x13 // set the flowcontrol special chars, value=0, buf=6 bytes, |
| 110 | // last 2 bytes contain flowcontrol chars e.g. 00 00 00 00 11 13 |
| 111 | |
| 112 | /* values used for request IPW_SIO_SET_PIN */ |
| 113 | #define IPW_PIN_SETDTR 0x101 |
| 114 | #define IPW_PIN_SETRTS 0x202 |
| 115 | #define IPW_PIN_CLRDTR 0x100 |
| 116 | #define IPW_PIN_CLRRTS 0x200 // unconfirmed |
| 117 | |
| 118 | /* values used for request IPW_SIO_RXCTL */ |
| 119 | #define IPW_RXBULK_ON 1 |
| 120 | #define IPW_RXBULK_OFF 0 |
| 121 | |
| 122 | /* various 16 byte hardcoded transferbuffers used by flow control */ |
| 123 | #define IPW_BYTES_FLOWINIT { 0x01, 0, 0, 0, 0x40, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 } |
| 124 | |
| 125 | /* Interpretation of modem status lines */ |
| 126 | /* These need sorting out by individually connecting pins and checking |
| 127 | * results. FIXME! |
| 128 | * When data is being sent we see 0x30 in the lower byte; this must |
| 129 | * contain DSR and CTS ... |
| 130 | */ |
| 131 | #define IPW_DSR ((1<<4) | (1<<5)) |
| 132 | #define IPW_CTS ((1<<5) | (1<<4)) |
| 133 | |
| 134 | #define IPW_WANTS_TO_SEND 0x30 |
| 135 | //#define IPW_DTR /* Data Terminal Ready */ |
| 136 | //#define IPW_CTS /* Clear To Send */ |
| 137 | //#define IPW_CD /* Carrier Detect */ |
| 138 | //#define IPW_DSR /* Data Set Ready */ |
| 139 | //#define IPW_RxD /* Receive pin */ |
| 140 | |
| 141 | //#define IPW_LE |
| 142 | //#define IPW_RTS |
| 143 | //#define IPW_ST |
| 144 | //#define IPW_SR |
| 145 | //#define IPW_RI /* Ring Indicator */ |
| 146 | |
| 147 | static struct usb_device_id usb_ipw_ids[] = { |
| 148 | { USB_DEVICE(IPW_VID, IPW_PID) }, |
| 149 | { }, |
| 150 | }; |
| 151 | |
| 152 | MODULE_DEVICE_TABLE(usb, usb_ipw_ids); |
| 153 | |
| 154 | static struct usb_driver usb_ipw_driver = { |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 155 | .name = "ipwtty", |
| 156 | .probe = usb_serial_probe, |
| 157 | .disconnect = usb_serial_disconnect, |
| 158 | .id_table = usb_ipw_ids, |
Greg Kroah-Hartman | ba9dc65 | 2005-11-16 13:41:28 -0800 | [diff] [blame] | 159 | .no_dynamic_id = 1, |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 160 | }; |
| 161 | |
| 162 | static int debug; |
| 163 | |
| 164 | static void ipw_read_bulk_callback(struct urb *urb, struct pt_regs *regs) |
| 165 | { |
| 166 | struct usb_serial_port *port = urb->context; |
| 167 | unsigned char *data = urb->transfer_buffer; |
| 168 | struct tty_struct *tty; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 169 | int result; |
| 170 | |
| 171 | dbg("%s - port %d", __FUNCTION__, port->number); |
| 172 | |
| 173 | if (urb->status) { |
| 174 | dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status); |
| 175 | return; |
| 176 | } |
| 177 | |
| 178 | usb_serial_debug_data(debug, &port->dev, __FUNCTION__, urb->actual_length, data); |
| 179 | |
| 180 | tty = port->tty; |
| 181 | if (tty && urb->actual_length) { |
Alan Cox | 33f0f88 | 2006-01-09 20:54:13 -0800 | [diff] [blame] | 182 | tty_buffer_request_room(tty, urb->actual_length); |
| 183 | tty_insert_flip_string(tty, data, urb->actual_length); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 184 | tty_flip_buffer_push(tty); |
| 185 | } |
| 186 | |
| 187 | /* Continue trying to always read */ |
| 188 | usb_fill_bulk_urb (port->read_urb, port->serial->dev, |
| 189 | usb_rcvbulkpipe(port->serial->dev, |
| 190 | port->bulk_in_endpointAddress), |
| 191 | port->read_urb->transfer_buffer, |
| 192 | port->read_urb->transfer_buffer_length, |
| 193 | ipw_read_bulk_callback, port); |
| 194 | result = usb_submit_urb(port->read_urb, GFP_ATOMIC); |
| 195 | if (result) |
| 196 | dev_err(&port->dev, "%s - failed resubmitting read urb, error %d\n", __FUNCTION__, result); |
| 197 | return; |
| 198 | } |
| 199 | |
| 200 | static int ipw_open(struct usb_serial_port *port, struct file *filp) |
| 201 | { |
| 202 | struct usb_device *dev = port->serial->dev; |
| 203 | u8 buf_flow_static[16] = IPW_BYTES_FLOWINIT; |
| 204 | u8 *buf_flow_init; |
| 205 | int result; |
| 206 | |
| 207 | dbg("%s", __FUNCTION__); |
| 208 | |
| 209 | buf_flow_init = kmalloc(16, GFP_KERNEL); |
| 210 | if (!buf_flow_init) |
| 211 | return -ENOMEM; |
| 212 | memcpy(buf_flow_init, buf_flow_static, 16); |
| 213 | |
| 214 | if (port->tty) |
| 215 | port->tty->low_latency = 1; |
| 216 | |
| 217 | /* --1: Tell the modem to initialize (we think) From sniffs this is always the |
| 218 | * first thing that gets sent to the modem during opening of the device */ |
| 219 | dbg("%s: Sending SIO_INIT (we guess)",__FUNCTION__); |
| 220 | result = usb_control_msg(dev, usb_sndctrlpipe(dev,0), |
| 221 | IPW_SIO_INIT, |
| 222 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 223 | 0, |
| 224 | 0, /* index */ |
| 225 | NULL, |
| 226 | 0, |
| 227 | 100000); |
| 228 | if (result < 0) |
| 229 | dev_err(&port->dev, "Init of modem failed (error = %d)", result); |
| 230 | |
| 231 | /* reset the bulk pipes */ |
| 232 | usb_clear_halt(dev, usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress)); |
| 233 | usb_clear_halt(dev, usb_sndbulkpipe(dev, port->bulk_out_endpointAddress)); |
| 234 | |
| 235 | /*--2: Start reading from the device */ |
| 236 | dbg("%s: setting up bulk read callback",__FUNCTION__); |
| 237 | usb_fill_bulk_urb(port->read_urb, dev, |
| 238 | usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress), |
| 239 | port->bulk_in_buffer, |
| 240 | port->bulk_in_size, |
| 241 | ipw_read_bulk_callback, port); |
| 242 | result = usb_submit_urb(port->read_urb, GFP_KERNEL); |
| 243 | if (result < 0) |
| 244 | dbg("%s - usb_submit_urb(read bulk) failed with status %d", __FUNCTION__, result); |
| 245 | |
| 246 | /*--3: Tell the modem to open the floodgates on the rx bulk channel */ |
| 247 | dbg("%s:asking modem for RxRead (RXBULK_ON)",__FUNCTION__); |
| 248 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 249 | IPW_SIO_RXCTL, |
| 250 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 251 | IPW_RXBULK_ON, |
| 252 | 0, /* index */ |
| 253 | NULL, |
| 254 | 0, |
| 255 | 100000); |
| 256 | if (result < 0) |
| 257 | dev_err(&port->dev, "Enabling bulk RxRead failed (error = %d)", result); |
| 258 | |
| 259 | /*--4: setup the initial flowcontrol */ |
| 260 | dbg("%s:setting init flowcontrol (%s)",__FUNCTION__,buf_flow_init); |
| 261 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 262 | IPW_SIO_HANDFLOW, |
| 263 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 264 | 0, |
| 265 | 0, |
| 266 | buf_flow_init, |
| 267 | 0x10, |
| 268 | 200000); |
| 269 | if (result < 0) |
| 270 | dev_err(&port->dev, "initial flowcontrol failed (error = %d)", result); |
| 271 | |
| 272 | |
| 273 | /*--5: raise the dtr */ |
| 274 | dbg("%s:raising dtr",__FUNCTION__); |
| 275 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 276 | IPW_SIO_SET_PIN, |
| 277 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 278 | IPW_PIN_SETDTR, |
| 279 | 0, |
| 280 | NULL, |
| 281 | 0, |
| 282 | 200000); |
| 283 | if (result < 0) |
| 284 | dev_err(&port->dev, "setting dtr failed (error = %d)", result); |
| 285 | |
| 286 | /*--6: raise the rts */ |
| 287 | dbg("%s:raising rts",__FUNCTION__); |
| 288 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 289 | IPW_SIO_SET_PIN, |
| 290 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 291 | IPW_PIN_SETRTS, |
| 292 | 0, |
| 293 | NULL, |
| 294 | 0, |
| 295 | 200000); |
| 296 | if (result < 0) |
| 297 | dev_err(&port->dev, "setting dtr failed (error = %d)", result); |
| 298 | |
| 299 | kfree(buf_flow_init); |
| 300 | return 0; |
| 301 | } |
| 302 | |
| 303 | static void ipw_close(struct usb_serial_port *port, struct file * filp) |
| 304 | { |
| 305 | struct usb_device *dev = port->serial->dev; |
| 306 | int result; |
| 307 | |
| 308 | if (tty_hung_up_p(filp)) { |
| 309 | dbg("%s: tty_hung_up_p ...", __FUNCTION__); |
| 310 | return; |
| 311 | } |
| 312 | |
| 313 | /*--1: drop the dtr */ |
| 314 | dbg("%s:dropping dtr",__FUNCTION__); |
| 315 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 316 | IPW_SIO_SET_PIN, |
| 317 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 318 | IPW_PIN_CLRDTR, |
| 319 | 0, |
| 320 | NULL, |
| 321 | 0, |
| 322 | 200000); |
| 323 | if (result < 0) |
| 324 | dev_err(&port->dev, "dropping dtr failed (error = %d)", result); |
| 325 | |
| 326 | /*--2: drop the rts */ |
| 327 | dbg("%s:dropping rts",__FUNCTION__); |
| 328 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 329 | IPW_SIO_SET_PIN, USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 330 | IPW_PIN_CLRRTS, |
| 331 | 0, |
| 332 | NULL, |
| 333 | 0, |
| 334 | 200000); |
| 335 | if (result < 0) |
| 336 | dev_err(&port->dev, "dropping rts failed (error = %d)", result); |
| 337 | |
| 338 | |
| 339 | /*--3: purge */ |
| 340 | dbg("%s:sending purge",__FUNCTION__); |
| 341 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 342 | IPW_SIO_PURGE, USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 343 | 0x03, |
| 344 | 0, |
| 345 | NULL, |
| 346 | 0, |
| 347 | 200000); |
| 348 | if (result < 0) |
| 349 | dev_err(&port->dev, "purge failed (error = %d)", result); |
| 350 | |
| 351 | |
| 352 | /* send RXBULK_off (tell modem to stop transmitting bulk data on rx chan) */ |
| 353 | result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), |
| 354 | IPW_SIO_RXCTL, |
| 355 | USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, |
| 356 | IPW_RXBULK_OFF, |
| 357 | 0, /* index */ |
| 358 | NULL, |
| 359 | 0, |
| 360 | 100000); |
| 361 | |
| 362 | if (result < 0) |
| 363 | dev_err(&port->dev, "Disabling bulk RxRead failed (error = %d)", result); |
| 364 | |
| 365 | /* shutdown any in-flight urbs that we know about */ |
| 366 | usb_kill_urb(port->read_urb); |
| 367 | usb_kill_urb(port->write_urb); |
| 368 | } |
| 369 | |
| 370 | static void ipw_write_bulk_callback(struct urb *urb, struct pt_regs *regs) |
| 371 | { |
| 372 | struct usb_serial_port *port = urb->context; |
| 373 | |
| 374 | dbg("%s", __FUNCTION__); |
| 375 | |
| 376 | if (urb->status) |
| 377 | dbg("%s - nonzero write bulk status received: %d", __FUNCTION__, urb->status); |
| 378 | |
Pete Zaitcev | cf2c748 | 2006-05-22 21:58:49 -0700 | [diff] [blame^] | 379 | usb_serial_port_softint(port); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 380 | } |
| 381 | |
| 382 | static int ipw_write(struct usb_serial_port *port, const unsigned char *buf, int count) |
| 383 | { |
| 384 | struct usb_device *dev = port->serial->dev; |
| 385 | int ret; |
| 386 | |
| 387 | dbg("%s: TOP: count=%d, in_interrupt=%ld", __FUNCTION__, |
| 388 | count, in_interrupt() ); |
| 389 | |
| 390 | if (count == 0) { |
| 391 | dbg("%s - write request of 0 bytes", __FUNCTION__); |
| 392 | return 0; |
| 393 | } |
Greg Kroah-Hartman | 507ca9b | 2005-04-23 12:49:16 -0700 | [diff] [blame] | 394 | |
| 395 | spin_lock(&port->lock); |
| 396 | if (port->write_urb_busy) { |
| 397 | spin_unlock(&port->lock); |
| 398 | dbg("%s - already writing", __FUNCTION__); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 399 | return 0; |
Greg Kroah-Hartman | 507ca9b | 2005-04-23 12:49:16 -0700 | [diff] [blame] | 400 | } |
| 401 | port->write_urb_busy = 1; |
| 402 | spin_unlock(&port->lock); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 403 | |
| 404 | count = min(count, port->bulk_out_size); |
| 405 | memcpy(port->bulk_out_buffer, buf, count); |
| 406 | |
| 407 | dbg("%s count now:%d", __FUNCTION__, count); |
Greg Kroah-Hartman | 507ca9b | 2005-04-23 12:49:16 -0700 | [diff] [blame] | 408 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 409 | usb_fill_bulk_urb(port->write_urb, dev, |
| 410 | usb_sndbulkpipe(dev, port->bulk_out_endpointAddress), |
| 411 | port->write_urb->transfer_buffer, |
| 412 | count, |
| 413 | ipw_write_bulk_callback, |
| 414 | port); |
| 415 | |
| 416 | ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); |
| 417 | if (ret != 0) { |
Greg Kroah-Hartman | 507ca9b | 2005-04-23 12:49:16 -0700 | [diff] [blame] | 418 | port->write_urb_busy = 0; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 419 | dbg("%s - usb_submit_urb(write bulk) failed with error = %d", __FUNCTION__, ret); |
| 420 | return ret; |
| 421 | } |
| 422 | |
| 423 | dbg("%s returning %d", __FUNCTION__, count); |
| 424 | return count; |
| 425 | } |
| 426 | |
| 427 | static int ipw_probe(struct usb_serial_port *port) |
| 428 | { |
| 429 | return 0; |
| 430 | } |
| 431 | |
| 432 | static int ipw_disconnect(struct usb_serial_port *port) |
| 433 | { |
| 434 | usb_set_serial_port_data(port, NULL); |
| 435 | return 0; |
| 436 | } |
| 437 | |
Greg Kroah-Hartman | ea65370 | 2005-06-20 21:15:16 -0700 | [diff] [blame] | 438 | static struct usb_serial_driver ipw_device = { |
Greg Kroah-Hartman | 18fcac3 | 2005-06-20 21:15:16 -0700 | [diff] [blame] | 439 | .driver = { |
| 440 | .owner = THIS_MODULE, |
Greg Kroah-Hartman | 269bda1 | 2005-06-20 21:15:16 -0700 | [diff] [blame] | 441 | .name = "ipw", |
Greg Kroah-Hartman | 18fcac3 | 2005-06-20 21:15:16 -0700 | [diff] [blame] | 442 | }, |
Greg Kroah-Hartman | 269bda1 | 2005-06-20 21:15:16 -0700 | [diff] [blame] | 443 | .description = "IPWireless converter", |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 444 | .id_table = usb_ipw_ids, |
| 445 | .num_interrupt_in = NUM_DONT_CARE, |
| 446 | .num_bulk_in = 1, |
| 447 | .num_bulk_out = 1, |
| 448 | .num_ports = 1, |
| 449 | .open = ipw_open, |
| 450 | .close = ipw_close, |
| 451 | .port_probe = ipw_probe, |
| 452 | .port_remove = ipw_disconnect, |
| 453 | .write = ipw_write, |
| 454 | .write_bulk_callback = ipw_write_bulk_callback, |
| 455 | .read_bulk_callback = ipw_read_bulk_callback, |
| 456 | }; |
| 457 | |
| 458 | |
| 459 | |
| 460 | static int usb_ipw_init(void) |
| 461 | { |
| 462 | int retval; |
| 463 | |
| 464 | retval = usb_serial_register(&ipw_device); |
| 465 | if (retval) |
| 466 | return retval; |
| 467 | retval = usb_register(&usb_ipw_driver); |
| 468 | if (retval) { |
| 469 | usb_serial_deregister(&ipw_device); |
| 470 | return retval; |
| 471 | } |
| 472 | info(DRIVER_DESC " " DRIVER_VERSION); |
| 473 | return 0; |
| 474 | } |
| 475 | |
| 476 | static void usb_ipw_exit(void) |
| 477 | { |
| 478 | usb_deregister(&usb_ipw_driver); |
| 479 | usb_serial_deregister(&ipw_device); |
| 480 | } |
| 481 | |
| 482 | module_init(usb_ipw_init); |
| 483 | module_exit(usb_ipw_exit); |
| 484 | |
| 485 | /* Module information */ |
| 486 | MODULE_AUTHOR( DRIVER_AUTHOR ); |
| 487 | MODULE_DESCRIPTION( DRIVER_DESC ); |
| 488 | MODULE_LICENSE("GPL"); |
| 489 | |
| 490 | module_param(debug, bool, S_IRUGO | S_IWUSR); |
| 491 | MODULE_PARM_DESC(debug, "Debug enabled or not"); |