blob: 0fa9f6761763023c45b60b7582fb4e70e2b807c7 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * linux/drivers/serial/pmac_zilog.c
3 *
4 * Driver for PowerMac Z85c30 based ESCC cell found in the
5 * "macio" ASICs of various PowerMac models
6 *
7 * Copyright (C) 2003 Ben. Herrenschmidt (benh@kernel.crashing.org)
8 *
9 * Derived from drivers/macintosh/macserial.c by Paul Mackerras
10 * and drivers/serial/sunzilog.c by David S. Miller
11 *
12 * Hrm... actually, I ripped most of sunzilog (Thanks David !) and
13 * adapted special tweaks needed for us. I don't think it's worth
14 * merging back those though. The DMA code still has to get in
15 * and once done, I expect that driver to remain fairly stable in
16 * the long term, unless we change the driver model again...
17 *
18 * This program is free software; you can redistribute it and/or modify
19 * it under the terms of the GNU General Public License as published by
20 * the Free Software Foundation; either version 2 of the License, or
21 * (at your option) any later version.
22 *
23 * This program is distributed in the hope that it will be useful,
24 * but WITHOUT ANY WARRANTY; without even the implied warranty of
25 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
26 * GNU General Public License for more details.
27 *
28 * You should have received a copy of the GNU General Public License
29 * along with this program; if not, write to the Free Software
30 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
31 *
32 * 2004-08-06 Harald Welte <laforge@gnumonks.org>
33 * - Enable BREAK interrupt
34 * - Add support for sysreq
35 *
36 * TODO: - Add DMA support
37 * - Defer port shutdown to a few seconds after close
38 * - maybe put something right into uap->clk_divisor
39 */
40
41#undef DEBUG
42#undef DEBUG_HARD
43#undef USE_CTRL_O_SYSRQ
44
Linus Torvalds1da177e2005-04-16 15:20:36 -070045#include <linux/module.h>
46#include <linux/tty.h>
47
48#include <linux/tty_flip.h>
49#include <linux/major.h>
50#include <linux/string.h>
51#include <linux/fcntl.h>
52#include <linux/mm.h>
53#include <linux/kernel.h>
54#include <linux/delay.h>
55#include <linux/init.h>
56#include <linux/console.h>
57#include <linux/slab.h>
58#include <linux/adb.h>
59#include <linux/pmu.h>
60#include <linux/bitops.h>
61#include <linux/sysrq.h>
Arjan van de Venf392ecf2006-01-12 18:44:32 +000062#include <linux/mutex.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070063#include <asm/sections.h>
64#include <asm/io.h>
65#include <asm/irq.h>
66#include <asm/prom.h>
67#include <asm/machdep.h>
68#include <asm/pmac_feature.h>
69#include <asm/dbdma.h>
70#include <asm/macio.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070071
72#if defined (CONFIG_SERIAL_PMACZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
73#define SUPPORT_SYSRQ
74#endif
75
76#include <linux/serial.h>
77#include <linux/serial_core.h>
78
79#include "pmac_zilog.h"
80
81/* Not yet implemented */
82#undef HAS_DBDMA
83
84static char version[] __initdata = "pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)";
85MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>");
86MODULE_DESCRIPTION("Driver for the PowerMac serial ports.");
87MODULE_LICENSE("GPL");
88
89#define PWRDBG(fmt, arg...) printk(KERN_DEBUG fmt , ## arg)
90
91
92/*
93 * For the sake of early serial console, we can do a pre-probe
94 * (optional) of the ports at rather early boot time.
95 */
96static struct uart_pmac_port pmz_ports[MAX_ZS_PORTS];
97static int pmz_ports_count;
Arjan van de Venf392ecf2006-01-12 18:44:32 +000098static DEFINE_MUTEX(pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -070099
100static struct uart_driver pmz_uart_reg = {
101 .owner = THIS_MODULE,
102 .driver_name = "ttyS",
Linus Torvalds1da177e2005-04-16 15:20:36 -0700103 .dev_name = "ttyS",
104 .major = TTY_MAJOR,
105};
106
107
108/*
109 * Load all registers to reprogram the port
110 * This function must only be called when the TX is not busy. The UART
111 * port lock must be held and local interrupts disabled.
112 */
113static void pmz_load_zsregs(struct uart_pmac_port *uap, u8 *regs)
114{
115 int i;
116
117 if (ZS_IS_ASLEEP(uap))
118 return;
119
120 /* Let pending transmits finish. */
121 for (i = 0; i < 1000; i++) {
122 unsigned char stat = read_zsreg(uap, R1);
123 if (stat & ALL_SNT)
124 break;
125 udelay(100);
126 }
127
128 ZS_CLEARERR(uap);
129 zssync(uap);
130 ZS_CLEARFIFO(uap);
131 zssync(uap);
132 ZS_CLEARERR(uap);
133
134 /* Disable all interrupts. */
135 write_zsreg(uap, R1,
136 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
137
138 /* Set parity, sync config, stop bits, and clock divisor. */
139 write_zsreg(uap, R4, regs[R4]);
140
141 /* Set misc. TX/RX control bits. */
142 write_zsreg(uap, R10, regs[R10]);
143
144 /* Set TX/RX controls sans the enable bits. */
145 write_zsreg(uap, R3, regs[R3] & ~RxENABLE);
146 write_zsreg(uap, R5, regs[R5] & ~TxENABLE);
147
148 /* now set R7 "prime" on ESCC */
149 write_zsreg(uap, R15, regs[R15] | EN85C30);
150 write_zsreg(uap, R7, regs[R7P]);
151
152 /* make sure we use R7 "non-prime" on ESCC */
153 write_zsreg(uap, R15, regs[R15] & ~EN85C30);
154
155 /* Synchronous mode config. */
156 write_zsreg(uap, R6, regs[R6]);
157 write_zsreg(uap, R7, regs[R7]);
158
159 /* Disable baud generator. */
160 write_zsreg(uap, R14, regs[R14] & ~BRENAB);
161
162 /* Clock mode control. */
163 write_zsreg(uap, R11, regs[R11]);
164
165 /* Lower and upper byte of baud rate generator divisor. */
166 write_zsreg(uap, R12, regs[R12]);
167 write_zsreg(uap, R13, regs[R13]);
168
169 /* Now rewrite R14, with BRENAB (if set). */
170 write_zsreg(uap, R14, regs[R14]);
171
172 /* Reset external status interrupts. */
173 write_zsreg(uap, R0, RES_EXT_INT);
174 write_zsreg(uap, R0, RES_EXT_INT);
175
176 /* Rewrite R3/R5, this time without enables masked. */
177 write_zsreg(uap, R3, regs[R3]);
178 write_zsreg(uap, R5, regs[R5]);
179
180 /* Rewrite R1, this time without IRQ enabled masked. */
181 write_zsreg(uap, R1, regs[R1]);
182
183 /* Enable interrupts */
184 write_zsreg(uap, R9, regs[R9]);
185}
186
187/*
188 * We do like sunzilog to avoid disrupting pending Tx
189 * Reprogram the Zilog channel HW registers with the copies found in the
190 * software state struct. If the transmitter is busy, we defer this update
191 * until the next TX complete interrupt. Else, we do it right now.
192 *
193 * The UART port lock must be held and local interrupts disabled.
194 */
195static void pmz_maybe_update_regs(struct uart_pmac_port *uap)
196{
197 if (!ZS_REGS_HELD(uap)) {
198 if (ZS_TX_ACTIVE(uap)) {
199 uap->flags |= PMACZILOG_FLAG_REGS_HELD;
200 } else {
201 pmz_debug("pmz: maybe_update_regs: updating\n");
202 pmz_load_zsregs(uap, uap->curregs);
203 }
204 }
205}
206
David Howells7d12e782006-10-05 14:55:46 +0100207static struct tty_struct *pmz_receive_chars(struct uart_pmac_port *uap)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700208{
209 struct tty_struct *tty = NULL;
Alan Cox33f0f882006-01-09 20:54:13 -0800210 unsigned char ch, r1, drop, error, flag;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700211 int loops = 0;
212
Linus Torvalds1da177e2005-04-16 15:20:36 -0700213 /* The interrupt can be enabled when the port isn't open, typically
214 * that happens when using one port is open and the other closed (stale
215 * interrupt) or when one port is used as a console.
216 */
217 if (!ZS_IS_OPEN(uap)) {
218 pmz_debug("pmz: draining input\n");
219 /* Port is closed, drain input data */
220 for (;;) {
221 if ((++loops) > 1000)
222 goto flood;
223 (void)read_zsreg(uap, R1);
224 write_zsreg(uap, R0, ERR_RES);
225 (void)read_zsdata(uap);
226 ch = read_zsreg(uap, R0);
227 if (!(ch & Rx_CH_AV))
228 break;
229 }
230 return NULL;
231 }
232
233 /* Sanity check, make sure the old bug is no longer happening */
234 if (uap->port.info == NULL || uap->port.info->tty == NULL) {
235 WARN_ON(1);
236 (void)read_zsdata(uap);
237 return NULL;
238 }
239 tty = uap->port.info->tty;
240
241 while (1) {
242 error = 0;
243 drop = 0;
244
Linus Torvalds1da177e2005-04-16 15:20:36 -0700245 r1 = read_zsreg(uap, R1);
246 ch = read_zsdata(uap);
247
248 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
249 write_zsreg(uap, R0, ERR_RES);
250 zssync(uap);
251 }
252
253 ch &= uap->parity_mask;
254 if (ch == 0 && uap->flags & PMACZILOG_FLAG_BREAK) {
255 uap->flags &= ~PMACZILOG_FLAG_BREAK;
256 }
257
258#if defined(CONFIG_MAGIC_SYSRQ) && defined(CONFIG_SERIAL_CORE_CONSOLE)
259#ifdef USE_CTRL_O_SYSRQ
260 /* Handle the SysRq ^O Hack */
261 if (ch == '\x0f') {
262 uap->port.sysrq = jiffies + HZ*5;
263 goto next_char;
264 }
265#endif /* USE_CTRL_O_SYSRQ */
266 if (uap->port.sysrq) {
267 int swallow;
268 spin_unlock(&uap->port.lock);
David Howells7d12e782006-10-05 14:55:46 +0100269 swallow = uart_handle_sysrq_char(&uap->port, ch);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700270 spin_lock(&uap->port.lock);
271 if (swallow)
272 goto next_char;
273 }
274#endif /* CONFIG_MAGIC_SYSRQ && CONFIG_SERIAL_CORE_CONSOLE */
275
276 /* A real serial line, record the character and status. */
277 if (drop)
278 goto next_char;
279
Alan Cox33f0f882006-01-09 20:54:13 -0800280 flag = TTY_NORMAL;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700281 uap->port.icount.rx++;
282
283 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) {
284 error = 1;
285 if (r1 & BRK_ABRT) {
286 pmz_debug("pmz: got break !\n");
287 r1 &= ~(PAR_ERR | CRC_ERR);
288 uap->port.icount.brk++;
289 if (uart_handle_break(&uap->port))
290 goto next_char;
291 }
292 else if (r1 & PAR_ERR)
293 uap->port.icount.parity++;
294 else if (r1 & CRC_ERR)
295 uap->port.icount.frame++;
296 if (r1 & Rx_OVR)
297 uap->port.icount.overrun++;
298 r1 &= uap->port.read_status_mask;
299 if (r1 & BRK_ABRT)
Alan Cox33f0f882006-01-09 20:54:13 -0800300 flag = TTY_BREAK;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700301 else if (r1 & PAR_ERR)
Alan Cox33f0f882006-01-09 20:54:13 -0800302 flag = TTY_PARITY;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700303 else if (r1 & CRC_ERR)
Alan Cox33f0f882006-01-09 20:54:13 -0800304 flag = TTY_FRAME;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700305 }
306
307 if (uap->port.ignore_status_mask == 0xff ||
308 (r1 & uap->port.ignore_status_mask) == 0) {
Alan Cox33f0f882006-01-09 20:54:13 -0800309 tty_insert_flip_char(tty, ch, flag);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700310 }
Alan Cox33f0f882006-01-09 20:54:13 -0800311 if (r1 & Rx_OVR)
312 tty_insert_flip_char(tty, 0, TTY_OVERRUN);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700313 next_char:
314 /* We can get stuck in an infinite loop getting char 0 when the
315 * line is in a wrong HW state, we break that here.
316 * When that happens, I disable the receive side of the driver.
317 * Note that what I've been experiencing is a real irq loop where
318 * I'm getting flooded regardless of the actual port speed.
319 * Something stange is going on with the HW
320 */
321 if ((++loops) > 1000)
322 goto flood;
323 ch = read_zsreg(uap, R0);
324 if (!(ch & Rx_CH_AV))
325 break;
326 }
327
328 return tty;
329 flood:
330 uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
331 write_zsreg(uap, R1, uap->curregs[R1]);
332 zssync(uap);
333 dev_err(&uap->dev->ofdev.dev, "pmz: rx irq flood !\n");
334 return tty;
335}
336
David Howells7d12e782006-10-05 14:55:46 +0100337static void pmz_status_handle(struct uart_pmac_port *uap)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700338{
339 unsigned char status;
340
341 status = read_zsreg(uap, R0);
342 write_zsreg(uap, R0, RES_EXT_INT);
343 zssync(uap);
344
345 if (ZS_IS_OPEN(uap) && ZS_WANTS_MODEM_STATUS(uap)) {
346 if (status & SYNC_HUNT)
347 uap->port.icount.dsr++;
348
349 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
350 * But it does not tell us which bit has changed, we have to keep
351 * track of this ourselves.
352 * The CTS input is inverted for some reason. -- paulus
353 */
354 if ((status ^ uap->prev_status) & DCD)
355 uart_handle_dcd_change(&uap->port,
356 (status & DCD));
357 if ((status ^ uap->prev_status) & CTS)
358 uart_handle_cts_change(&uap->port,
359 !(status & CTS));
360
361 wake_up_interruptible(&uap->port.info->delta_msr_wait);
362 }
363
364 if (status & BRK_ABRT)
365 uap->flags |= PMACZILOG_FLAG_BREAK;
366
367 uap->prev_status = status;
368}
369
370static void pmz_transmit_chars(struct uart_pmac_port *uap)
371{
372 struct circ_buf *xmit;
373
374 if (ZS_IS_ASLEEP(uap))
375 return;
376 if (ZS_IS_CONS(uap)) {
377 unsigned char status = read_zsreg(uap, R0);
378
379 /* TX still busy? Just wait for the next TX done interrupt.
380 *
381 * It can occur because of how we do serial console writes. It would
382 * be nice to transmit console writes just like we normally would for
383 * a TTY line. (ie. buffered and TX interrupt driven). That is not
384 * easy because console writes cannot sleep. One solution might be
385 * to poll on enough port->xmit space becomming free. -DaveM
386 */
387 if (!(status & Tx_BUF_EMP))
388 return;
389 }
390
391 uap->flags &= ~PMACZILOG_FLAG_TX_ACTIVE;
392
393 if (ZS_REGS_HELD(uap)) {
394 pmz_load_zsregs(uap, uap->curregs);
395 uap->flags &= ~PMACZILOG_FLAG_REGS_HELD;
396 }
397
398 if (ZS_TX_STOPPED(uap)) {
399 uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
400 goto ack_tx_int;
401 }
402
403 if (uap->port.x_char) {
404 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
405 write_zsdata(uap, uap->port.x_char);
406 zssync(uap);
407 uap->port.icount.tx++;
408 uap->port.x_char = 0;
409 return;
410 }
411
412 if (uap->port.info == NULL)
413 goto ack_tx_int;
414 xmit = &uap->port.info->xmit;
415 if (uart_circ_empty(xmit)) {
416 uart_write_wakeup(&uap->port);
417 goto ack_tx_int;
418 }
419 if (uart_tx_stopped(&uap->port))
420 goto ack_tx_int;
421
422 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
423 write_zsdata(uap, xmit->buf[xmit->tail]);
424 zssync(uap);
425
426 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
427 uap->port.icount.tx++;
428
429 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
430 uart_write_wakeup(&uap->port);
431
432 return;
433
434ack_tx_int:
435 write_zsreg(uap, R0, RES_Tx_P);
436 zssync(uap);
437}
438
439/* Hrm... we register that twice, fixme later.... */
David Howells7d12e782006-10-05 14:55:46 +0100440static irqreturn_t pmz_interrupt(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700441{
442 struct uart_pmac_port *uap = dev_id;
443 struct uart_pmac_port *uap_a;
444 struct uart_pmac_port *uap_b;
445 int rc = IRQ_NONE;
446 struct tty_struct *tty;
447 u8 r3;
448
449 uap_a = pmz_get_port_A(uap);
450 uap_b = uap_a->mate;
451
452 spin_lock(&uap_a->port.lock);
453 r3 = read_zsreg(uap_a, R3);
454
455#ifdef DEBUG_HARD
456 pmz_debug("irq, r3: %x\n", r3);
457#endif
458 /* Channel A */
459 tty = NULL;
460 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
461 write_zsreg(uap_a, R0, RES_H_IUS);
462 zssync(uap_a);
463 if (r3 & CHAEXT)
David Howells7d12e782006-10-05 14:55:46 +0100464 pmz_status_handle(uap_a);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700465 if (r3 & CHARxIP)
David Howells7d12e782006-10-05 14:55:46 +0100466 tty = pmz_receive_chars(uap_a);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700467 if (r3 & CHATxIP)
468 pmz_transmit_chars(uap_a);
469 rc = IRQ_HANDLED;
470 }
471 spin_unlock(&uap_a->port.lock);
472 if (tty != NULL)
473 tty_flip_buffer_push(tty);
474
475 if (uap_b->node == NULL)
476 goto out;
477
478 spin_lock(&uap_b->port.lock);
479 tty = NULL;
480 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
481 write_zsreg(uap_b, R0, RES_H_IUS);
482 zssync(uap_b);
483 if (r3 & CHBEXT)
David Howells7d12e782006-10-05 14:55:46 +0100484 pmz_status_handle(uap_b);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700485 if (r3 & CHBRxIP)
David Howells7d12e782006-10-05 14:55:46 +0100486 tty = pmz_receive_chars(uap_b);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700487 if (r3 & CHBTxIP)
488 pmz_transmit_chars(uap_b);
489 rc = IRQ_HANDLED;
490 }
491 spin_unlock(&uap_b->port.lock);
492 if (tty != NULL)
493 tty_flip_buffer_push(tty);
494
495 out:
496#ifdef DEBUG_HARD
497 pmz_debug("irq done.\n");
498#endif
499 return rc;
500}
501
502/*
503 * Peek the status register, lock not held by caller
504 */
505static inline u8 pmz_peek_status(struct uart_pmac_port *uap)
506{
507 unsigned long flags;
508 u8 status;
509
510 spin_lock_irqsave(&uap->port.lock, flags);
511 status = read_zsreg(uap, R0);
512 spin_unlock_irqrestore(&uap->port.lock, flags);
513
514 return status;
515}
516
517/*
518 * Check if transmitter is empty
519 * The port lock is not held.
520 */
521static unsigned int pmz_tx_empty(struct uart_port *port)
522{
523 struct uart_pmac_port *uap = to_pmz(port);
524 unsigned char status;
525
526 if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
527 return TIOCSER_TEMT;
528
529 status = pmz_peek_status(to_pmz(port));
530 if (status & Tx_BUF_EMP)
531 return TIOCSER_TEMT;
532 return 0;
533}
534
535/*
536 * Set Modem Control (RTS & DTR) bits
537 * The port lock is held and interrupts are disabled.
538 * Note: Shall we really filter out RTS on external ports or
539 * should that be dealt at higher level only ?
540 */
541static void pmz_set_mctrl(struct uart_port *port, unsigned int mctrl)
542{
543 struct uart_pmac_port *uap = to_pmz(port);
544 unsigned char set_bits, clear_bits;
545
546 /* Do nothing for irda for now... */
547 if (ZS_IS_IRDA(uap))
548 return;
549 /* We get called during boot with a port not up yet */
550 if (ZS_IS_ASLEEP(uap) ||
551 !(ZS_IS_OPEN(uap) || ZS_IS_CONS(uap)))
552 return;
553
554 set_bits = clear_bits = 0;
555
556 if (ZS_IS_INTMODEM(uap)) {
557 if (mctrl & TIOCM_RTS)
558 set_bits |= RTS;
559 else
560 clear_bits |= RTS;
561 }
562 if (mctrl & TIOCM_DTR)
563 set_bits |= DTR;
564 else
565 clear_bits |= DTR;
566
567 /* NOTE: Not subject to 'transmitter active' rule. */
568 uap->curregs[R5] |= set_bits;
569 uap->curregs[R5] &= ~clear_bits;
570 if (ZS_IS_ASLEEP(uap))
571 return;
572 write_zsreg(uap, R5, uap->curregs[R5]);
573 pmz_debug("pmz_set_mctrl: set bits: %x, clear bits: %x -> %x\n",
574 set_bits, clear_bits, uap->curregs[R5]);
575 zssync(uap);
576}
577
578/*
579 * Get Modem Control bits (only the input ones, the core will
580 * or that with a cached value of the control ones)
Russell Kingc5f46442005-06-29 09:42:38 +0100581 * The port lock is held and interrupts are disabled.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700582 */
583static unsigned int pmz_get_mctrl(struct uart_port *port)
584{
585 struct uart_pmac_port *uap = to_pmz(port);
586 unsigned char status;
587 unsigned int ret;
588
589 if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
590 return 0;
591
Russell Kingc5f46442005-06-29 09:42:38 +0100592 status = read_zsreg(uap, R0);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700593
594 ret = 0;
595 if (status & DCD)
596 ret |= TIOCM_CAR;
597 if (status & SYNC_HUNT)
598 ret |= TIOCM_DSR;
599 if (!(status & CTS))
600 ret |= TIOCM_CTS;
601
602 return ret;
603}
604
605/*
606 * Stop TX side. Dealt like sunzilog at next Tx interrupt,
Russell Kingb129a8c2005-08-31 10:12:14 +0100607 * though for DMA, we will have to do a bit more.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700608 * The port lock is held and interrupts are disabled.
609 */
Russell Kingb129a8c2005-08-31 10:12:14 +0100610static void pmz_stop_tx(struct uart_port *port)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700611{
612 to_pmz(port)->flags |= PMACZILOG_FLAG_TX_STOPPED;
613}
614
615/*
616 * Kick the Tx side.
617 * The port lock is held and interrupts are disabled.
618 */
Russell Kingb129a8c2005-08-31 10:12:14 +0100619static void pmz_start_tx(struct uart_port *port)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700620{
621 struct uart_pmac_port *uap = to_pmz(port);
622 unsigned char status;
623
624 pmz_debug("pmz: start_tx()\n");
625
626 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
627 uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
628
629 if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
630 return;
631
632 status = read_zsreg(uap, R0);
633
634 /* TX busy? Just wait for the TX done interrupt. */
635 if (!(status & Tx_BUF_EMP))
636 return;
637
638 /* Send the first character to jump-start the TX done
639 * IRQ sending engine.
640 */
641 if (port->x_char) {
642 write_zsdata(uap, port->x_char);
643 zssync(uap);
644 port->icount.tx++;
645 port->x_char = 0;
646 } else {
647 struct circ_buf *xmit = &port->info->xmit;
648
649 write_zsdata(uap, xmit->buf[xmit->tail]);
650 zssync(uap);
651 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
652 port->icount.tx++;
653
654 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
655 uart_write_wakeup(&uap->port);
656 }
657 pmz_debug("pmz: start_tx() done.\n");
658}
659
660/*
661 * Stop Rx side, basically disable emitting of
662 * Rx interrupts on the port. We don't disable the rx
663 * side of the chip proper though
664 * The port lock is held.
665 */
666static void pmz_stop_rx(struct uart_port *port)
667{
668 struct uart_pmac_port *uap = to_pmz(port);
669
670 if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
671 return;
672
673 pmz_debug("pmz: stop_rx()()\n");
674
675 /* Disable all RX interrupts. */
676 uap->curregs[R1] &= ~RxINT_MASK;
677 pmz_maybe_update_regs(uap);
678
679 pmz_debug("pmz: stop_rx() done.\n");
680}
681
682/*
683 * Enable modem status change interrupts
684 * The port lock is held.
685 */
686static void pmz_enable_ms(struct uart_port *port)
687{
688 struct uart_pmac_port *uap = to_pmz(port);
689 unsigned char new_reg;
690
691 if (ZS_IS_IRDA(uap) || uap->node == NULL)
692 return;
693 new_reg = uap->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
694 if (new_reg != uap->curregs[R15]) {
695 uap->curregs[R15] = new_reg;
696
697 if (ZS_IS_ASLEEP(uap))
698 return;
699 /* NOTE: Not subject to 'transmitter active' rule. */
700 write_zsreg(uap, R15, uap->curregs[R15]);
701 }
702}
703
704/*
705 * Control break state emission
706 * The port lock is not held.
707 */
708static void pmz_break_ctl(struct uart_port *port, int break_state)
709{
710 struct uart_pmac_port *uap = to_pmz(port);
711 unsigned char set_bits, clear_bits, new_reg;
712 unsigned long flags;
713
714 if (uap->node == NULL)
715 return;
716 set_bits = clear_bits = 0;
717
718 if (break_state)
719 set_bits |= SND_BRK;
720 else
721 clear_bits |= SND_BRK;
722
723 spin_lock_irqsave(&port->lock, flags);
724
725 new_reg = (uap->curregs[R5] | set_bits) & ~clear_bits;
726 if (new_reg != uap->curregs[R5]) {
727 uap->curregs[R5] = new_reg;
728
729 /* NOTE: Not subject to 'transmitter active' rule. */
730 if (ZS_IS_ASLEEP(uap))
731 return;
732 write_zsreg(uap, R5, uap->curregs[R5]);
733 }
734
735 spin_unlock_irqrestore(&port->lock, flags);
736}
737
738/*
739 * Turn power on or off to the SCC and associated stuff
740 * (port drivers, modem, IR port, etc.)
741 * Returns the number of milliseconds we should wait before
742 * trying to use the port.
743 */
744static int pmz_set_scc_power(struct uart_pmac_port *uap, int state)
745{
746 int delay = 0;
747 int rc;
748
749 if (state) {
750 rc = pmac_call_feature(
751 PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 1);
752 pmz_debug("port power on result: %d\n", rc);
753 if (ZS_IS_INTMODEM(uap)) {
754 rc = pmac_call_feature(
755 PMAC_FTR_MODEM_ENABLE, uap->node, 0, 1);
756 delay = 2500; /* wait for 2.5s before using */
757 pmz_debug("modem power result: %d\n", rc);
758 }
759 } else {
760 /* TODO: Make that depend on a timer, don't power down
761 * immediately
762 */
763 if (ZS_IS_INTMODEM(uap)) {
764 rc = pmac_call_feature(
765 PMAC_FTR_MODEM_ENABLE, uap->node, 0, 0);
766 pmz_debug("port power off result: %d\n", rc);
767 }
768 pmac_call_feature(PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 0);
769 }
770 return delay;
771}
772
773/*
774 * FixZeroBug....Works around a bug in the SCC receving channel.
775 * Inspired from Darwin code, 15 Sept. 2000 -DanM
776 *
777 * The following sequence prevents a problem that is seen with O'Hare ASICs
778 * (most versions -- also with some Heathrow and Hydra ASICs) where a zero
779 * at the input to the receiver becomes 'stuck' and locks up the receiver.
780 * This problem can occur as a result of a zero bit at the receiver input
781 * coincident with any of the following events:
782 *
783 * The SCC is initialized (hardware or software).
784 * A framing error is detected.
785 * The clocking option changes from synchronous or X1 asynchronous
786 * clocking to X16, X32, or X64 asynchronous clocking.
787 * The decoding mode is changed among NRZ, NRZI, FM0, or FM1.
788 *
789 * This workaround attempts to recover from the lockup condition by placing
790 * the SCC in synchronous loopback mode with a fast clock before programming
791 * any of the asynchronous modes.
792 */
793static void pmz_fix_zero_bug_scc(struct uart_pmac_port *uap)
794{
795 write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
796 zssync(uap);
797 udelay(10);
798 write_zsreg(uap, 9, (ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB) | NV);
799 zssync(uap);
800
801 write_zsreg(uap, 4, X1CLK | MONSYNC);
802 write_zsreg(uap, 3, Rx8);
803 write_zsreg(uap, 5, Tx8 | RTS);
804 write_zsreg(uap, 9, NV); /* Didn't we already do this? */
805 write_zsreg(uap, 11, RCBR | TCBR);
806 write_zsreg(uap, 12, 0);
807 write_zsreg(uap, 13, 0);
808 write_zsreg(uap, 14, (LOOPBAK | BRSRC));
809 write_zsreg(uap, 14, (LOOPBAK | BRSRC | BRENAB));
810 write_zsreg(uap, 3, Rx8 | RxENABLE);
811 write_zsreg(uap, 0, RES_EXT_INT);
812 write_zsreg(uap, 0, RES_EXT_INT);
813 write_zsreg(uap, 0, RES_EXT_INT); /* to kill some time */
814
815 /* The channel should be OK now, but it is probably receiving
816 * loopback garbage.
817 * Switch to asynchronous mode, disable the receiver,
818 * and discard everything in the receive buffer.
819 */
820 write_zsreg(uap, 9, NV);
821 write_zsreg(uap, 4, X16CLK | SB_MASK);
822 write_zsreg(uap, 3, Rx8);
823
824 while (read_zsreg(uap, 0) & Rx_CH_AV) {
825 (void)read_zsreg(uap, 8);
826 write_zsreg(uap, 0, RES_EXT_INT);
827 write_zsreg(uap, 0, ERR_RES);
828 }
829}
830
831/*
832 * Real startup routine, powers up the hardware and sets up
833 * the SCC. Returns a delay in ms where you need to wait before
834 * actually using the port, this is typically the internal modem
835 * powerup delay. This routine expect the lock to be taken.
836 */
837static int __pmz_startup(struct uart_pmac_port *uap)
838{
839 int pwr_delay = 0;
840
841 memset(&uap->curregs, 0, sizeof(uap->curregs));
842
843 /* Power up the SCC & underlying hardware (modem/irda) */
844 pwr_delay = pmz_set_scc_power(uap, 1);
845
846 /* Nice buggy HW ... */
847 pmz_fix_zero_bug_scc(uap);
848
849 /* Reset the channel */
850 uap->curregs[R9] = 0;
851 write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
852 zssync(uap);
853 udelay(10);
854 write_zsreg(uap, 9, 0);
855 zssync(uap);
856
857 /* Clear the interrupt registers */
858 write_zsreg(uap, R1, 0);
859 write_zsreg(uap, R0, ERR_RES);
860 write_zsreg(uap, R0, ERR_RES);
861 write_zsreg(uap, R0, RES_H_IUS);
862 write_zsreg(uap, R0, RES_H_IUS);
863
864 /* Setup some valid baud rate */
865 uap->curregs[R4] = X16CLK | SB1;
866 uap->curregs[R3] = Rx8;
867 uap->curregs[R5] = Tx8 | RTS;
868 if (!ZS_IS_IRDA(uap))
869 uap->curregs[R5] |= DTR;
870 uap->curregs[R12] = 0;
871 uap->curregs[R13] = 0;
872 uap->curregs[R14] = BRENAB;
873
874 /* Clear handshaking, enable BREAK interrupts */
875 uap->curregs[R15] = BRKIE;
876
877 /* Master interrupt enable */
878 uap->curregs[R9] |= NV | MIE;
879
880 pmz_load_zsregs(uap, uap->curregs);
881
882 /* Enable receiver and transmitter. */
883 write_zsreg(uap, R3, uap->curregs[R3] |= RxENABLE);
884 write_zsreg(uap, R5, uap->curregs[R5] |= TxENABLE);
885
886 /* Remember status for DCD/CTS changes */
887 uap->prev_status = read_zsreg(uap, R0);
888
889
890 return pwr_delay;
891}
892
893static void pmz_irda_reset(struct uart_pmac_port *uap)
894{
895 uap->curregs[R5] |= DTR;
896 write_zsreg(uap, R5, uap->curregs[R5]);
897 zssync(uap);
898 mdelay(110);
899 uap->curregs[R5] &= ~DTR;
900 write_zsreg(uap, R5, uap->curregs[R5]);
901 zssync(uap);
902 mdelay(10);
903}
904
905/*
906 * This is the "normal" startup routine, using the above one
907 * wrapped with the lock and doing a schedule delay
908 */
909static int pmz_startup(struct uart_port *port)
910{
911 struct uart_pmac_port *uap = to_pmz(port);
912 unsigned long flags;
913 int pwr_delay = 0;
914
915 pmz_debug("pmz: startup()\n");
916
917 if (ZS_IS_ASLEEP(uap))
918 return -EAGAIN;
919 if (uap->node == NULL)
920 return -ENODEV;
921
Arjan van de Venf392ecf2006-01-12 18:44:32 +0000922 mutex_lock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700923
924 uap->flags |= PMACZILOG_FLAG_IS_OPEN;
925
926 /* A console is never powered down. Else, power up and
927 * initialize the chip
928 */
929 if (!ZS_IS_CONS(uap)) {
930 spin_lock_irqsave(&port->lock, flags);
931 pwr_delay = __pmz_startup(uap);
932 spin_unlock_irqrestore(&port->lock, flags);
933 }
934
935 pmz_get_port_A(uap)->flags |= PMACZILOG_FLAG_IS_IRQ_ON;
Thomas Gleixner40663cc2006-07-01 19:29:43 -0700936 if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED, "PowerMac Zilog", uap)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700937 dev_err(&uap->dev->ofdev.dev,
938 "Unable to register zs interrupt handler.\n");
939 pmz_set_scc_power(uap, 0);
Arjan van de Venf392ecf2006-01-12 18:44:32 +0000940 mutex_unlock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700941 return -ENXIO;
942 }
943
Arjan van de Venf392ecf2006-01-12 18:44:32 +0000944 mutex_unlock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700945
946 /* Right now, we deal with delay by blocking here, I'll be
947 * smarter later on
948 */
949 if (pwr_delay != 0) {
950 pmz_debug("pmz: delaying %d ms\n", pwr_delay);
951 msleep(pwr_delay);
952 }
953
954 /* IrDA reset is done now */
955 if (ZS_IS_IRDA(uap))
956 pmz_irda_reset(uap);
957
958 /* Enable interrupts emission from the chip */
959 spin_lock_irqsave(&port->lock, flags);
960 uap->curregs[R1] |= INT_ALL_Rx | TxINT_ENAB;
961 if (!ZS_IS_EXTCLK(uap))
962 uap->curregs[R1] |= EXT_INT_ENAB;
963 write_zsreg(uap, R1, uap->curregs[R1]);
964 spin_unlock_irqrestore(&port->lock, flags);
965
966 pmz_debug("pmz: startup() done.\n");
967
968 return 0;
969}
970
971static void pmz_shutdown(struct uart_port *port)
972{
973 struct uart_pmac_port *uap = to_pmz(port);
974 unsigned long flags;
975
976 pmz_debug("pmz: shutdown()\n");
977
978 if (uap->node == NULL)
979 return;
980
Arjan van de Venf392ecf2006-01-12 18:44:32 +0000981 mutex_lock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700982
983 /* Release interrupt handler */
984 free_irq(uap->port.irq, uap);
985
986 spin_lock_irqsave(&port->lock, flags);
987
988 uap->flags &= ~PMACZILOG_FLAG_IS_OPEN;
989
990 if (!ZS_IS_OPEN(uap->mate))
991 pmz_get_port_A(uap)->flags &= ~PMACZILOG_FLAG_IS_IRQ_ON;
992
993 /* Disable interrupts */
994 if (!ZS_IS_ASLEEP(uap)) {
995 uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
996 write_zsreg(uap, R1, uap->curregs[R1]);
997 zssync(uap);
998 }
999
1000 if (ZS_IS_CONS(uap) || ZS_IS_ASLEEP(uap)) {
1001 spin_unlock_irqrestore(&port->lock, flags);
Arjan van de Venf392ecf2006-01-12 18:44:32 +00001002 mutex_unlock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001003 return;
1004 }
1005
1006 /* Disable receiver and transmitter. */
1007 uap->curregs[R3] &= ~RxENABLE;
1008 uap->curregs[R5] &= ~TxENABLE;
1009
1010 /* Disable all interrupts and BRK assertion. */
1011 uap->curregs[R5] &= ~SND_BRK;
1012 pmz_maybe_update_regs(uap);
1013
1014 /* Shut the chip down */
1015 pmz_set_scc_power(uap, 0);
1016
1017 spin_unlock_irqrestore(&port->lock, flags);
1018
Arjan van de Venf392ecf2006-01-12 18:44:32 +00001019 mutex_unlock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001020
1021 pmz_debug("pmz: shutdown() done.\n");
1022}
1023
1024/* Shared by TTY driver and serial console setup. The port lock is held
1025 * and local interrupts are disabled.
1026 */
1027static void pmz_convert_to_zs(struct uart_pmac_port *uap, unsigned int cflag,
1028 unsigned int iflag, unsigned long baud)
1029{
1030 int brg;
1031
1032
1033 /* Switch to external clocking for IrDA high clock rates. That
1034 * code could be re-used for Midi interfaces with different
1035 * multipliers
1036 */
1037 if (baud >= 115200 && ZS_IS_IRDA(uap)) {
1038 uap->curregs[R4] = X1CLK;
1039 uap->curregs[R11] = RCTRxCP | TCTRxCP;
1040 uap->curregs[R14] = 0; /* BRG off */
1041 uap->curregs[R12] = 0;
1042 uap->curregs[R13] = 0;
1043 uap->flags |= PMACZILOG_FLAG_IS_EXTCLK;
1044 } else {
1045 switch (baud) {
1046 case ZS_CLOCK/16: /* 230400 */
1047 uap->curregs[R4] = X16CLK;
1048 uap->curregs[R11] = 0;
1049 uap->curregs[R14] = 0;
1050 break;
1051 case ZS_CLOCK/32: /* 115200 */
1052 uap->curregs[R4] = X32CLK;
1053 uap->curregs[R11] = 0;
1054 uap->curregs[R14] = 0;
1055 break;
1056 default:
1057 uap->curregs[R4] = X16CLK;
1058 uap->curregs[R11] = TCBR | RCBR;
1059 brg = BPS_TO_BRG(baud, ZS_CLOCK / 16);
1060 uap->curregs[R12] = (brg & 255);
1061 uap->curregs[R13] = ((brg >> 8) & 255);
1062 uap->curregs[R14] = BRENAB;
1063 }
1064 uap->flags &= ~PMACZILOG_FLAG_IS_EXTCLK;
1065 }
1066
1067 /* Character size, stop bits, and parity. */
1068 uap->curregs[3] &= ~RxN_MASK;
1069 uap->curregs[5] &= ~TxN_MASK;
1070
1071 switch (cflag & CSIZE) {
1072 case CS5:
1073 uap->curregs[3] |= Rx5;
1074 uap->curregs[5] |= Tx5;
1075 uap->parity_mask = 0x1f;
1076 break;
1077 case CS6:
1078 uap->curregs[3] |= Rx6;
1079 uap->curregs[5] |= Tx6;
1080 uap->parity_mask = 0x3f;
1081 break;
1082 case CS7:
1083 uap->curregs[3] |= Rx7;
1084 uap->curregs[5] |= Tx7;
1085 uap->parity_mask = 0x7f;
1086 break;
1087 case CS8:
1088 default:
1089 uap->curregs[3] |= Rx8;
1090 uap->curregs[5] |= Tx8;
1091 uap->parity_mask = 0xff;
1092 break;
1093 };
1094 uap->curregs[4] &= ~(SB_MASK);
1095 if (cflag & CSTOPB)
1096 uap->curregs[4] |= SB2;
1097 else
1098 uap->curregs[4] |= SB1;
1099 if (cflag & PARENB)
1100 uap->curregs[4] |= PAR_ENAB;
1101 else
1102 uap->curregs[4] &= ~PAR_ENAB;
1103 if (!(cflag & PARODD))
1104 uap->curregs[4] |= PAR_EVEN;
1105 else
1106 uap->curregs[4] &= ~PAR_EVEN;
1107
1108 uap->port.read_status_mask = Rx_OVR;
1109 if (iflag & INPCK)
1110 uap->port.read_status_mask |= CRC_ERR | PAR_ERR;
1111 if (iflag & (BRKINT | PARMRK))
1112 uap->port.read_status_mask |= BRK_ABRT;
1113
1114 uap->port.ignore_status_mask = 0;
1115 if (iflag & IGNPAR)
1116 uap->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
1117 if (iflag & IGNBRK) {
1118 uap->port.ignore_status_mask |= BRK_ABRT;
1119 if (iflag & IGNPAR)
1120 uap->port.ignore_status_mask |= Rx_OVR;
1121 }
1122
1123 if ((cflag & CREAD) == 0)
1124 uap->port.ignore_status_mask = 0xff;
1125}
1126
1127
1128/*
1129 * Set the irda codec on the imac to the specified baud rate.
1130 */
1131static void pmz_irda_setup(struct uart_pmac_port *uap, unsigned long *baud)
1132{
1133 u8 cmdbyte;
1134 int t, version;
1135
1136 switch (*baud) {
1137 /* SIR modes */
1138 case 2400:
1139 cmdbyte = 0x53;
1140 break;
1141 case 4800:
1142 cmdbyte = 0x52;
1143 break;
1144 case 9600:
1145 cmdbyte = 0x51;
1146 break;
1147 case 19200:
1148 cmdbyte = 0x50;
1149 break;
1150 case 38400:
1151 cmdbyte = 0x4f;
1152 break;
1153 case 57600:
1154 cmdbyte = 0x4e;
1155 break;
1156 case 115200:
1157 cmdbyte = 0x4d;
1158 break;
1159 /* The FIR modes aren't really supported at this point, how
1160 * do we select the speed ? via the FCR on KeyLargo ?
1161 */
1162 case 1152000:
1163 cmdbyte = 0;
1164 break;
1165 case 4000000:
1166 cmdbyte = 0;
1167 break;
1168 default: /* 9600 */
1169 cmdbyte = 0x51;
1170 *baud = 9600;
1171 break;
1172 }
1173
1174 /* Wait for transmitter to drain */
1175 t = 10000;
1176 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0
1177 || (read_zsreg(uap, R1) & ALL_SNT) == 0) {
1178 if (--t <= 0) {
1179 dev_err(&uap->dev->ofdev.dev, "transmitter didn't drain\n");
1180 return;
1181 }
1182 udelay(10);
1183 }
1184
1185 /* Drain the receiver too */
1186 t = 100;
1187 (void)read_zsdata(uap);
1188 (void)read_zsdata(uap);
1189 (void)read_zsdata(uap);
1190 mdelay(10);
1191 while (read_zsreg(uap, R0) & Rx_CH_AV) {
1192 read_zsdata(uap);
1193 mdelay(10);
1194 if (--t <= 0) {
1195 dev_err(&uap->dev->ofdev.dev, "receiver didn't drain\n");
1196 return;
1197 }
1198 }
1199
1200 /* Switch to command mode */
1201 uap->curregs[R5] |= DTR;
1202 write_zsreg(uap, R5, uap->curregs[R5]);
1203 zssync(uap);
1204 mdelay(1);
1205
1206 /* Switch SCC to 19200 */
1207 pmz_convert_to_zs(uap, CS8, 0, 19200);
1208 pmz_load_zsregs(uap, uap->curregs);
1209 mdelay(1);
1210
1211 /* Write get_version command byte */
1212 write_zsdata(uap, 1);
1213 t = 5000;
1214 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
1215 if (--t <= 0) {
1216 dev_err(&uap->dev->ofdev.dev,
1217 "irda_setup timed out on get_version byte\n");
1218 goto out;
1219 }
1220 udelay(10);
1221 }
1222 version = read_zsdata(uap);
1223
1224 if (version < 4) {
1225 dev_info(&uap->dev->ofdev.dev, "IrDA: dongle version %d not supported\n",
1226 version);
1227 goto out;
1228 }
1229
1230 /* Send speed mode */
1231 write_zsdata(uap, cmdbyte);
1232 t = 5000;
1233 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
1234 if (--t <= 0) {
1235 dev_err(&uap->dev->ofdev.dev,
1236 "irda_setup timed out on speed mode byte\n");
1237 goto out;
1238 }
1239 udelay(10);
1240 }
1241 t = read_zsdata(uap);
1242 if (t != cmdbyte)
1243 dev_err(&uap->dev->ofdev.dev,
1244 "irda_setup speed mode byte = %x (%x)\n", t, cmdbyte);
1245
1246 dev_info(&uap->dev->ofdev.dev, "IrDA setup for %ld bps, dongle version: %d\n",
1247 *baud, version);
1248
1249 (void)read_zsdata(uap);
1250 (void)read_zsdata(uap);
1251 (void)read_zsdata(uap);
1252
1253 out:
1254 /* Switch back to data mode */
1255 uap->curregs[R5] &= ~DTR;
1256 write_zsreg(uap, R5, uap->curregs[R5]);
1257 zssync(uap);
1258
1259 (void)read_zsdata(uap);
1260 (void)read_zsdata(uap);
1261 (void)read_zsdata(uap);
1262}
1263
1264
Alan Cox606d0992006-12-08 02:38:45 -08001265static void __pmz_set_termios(struct uart_port *port, struct ktermios *termios,
1266 struct ktermios *old)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001267{
1268 struct uart_pmac_port *uap = to_pmz(port);
1269 unsigned long baud;
1270
1271 pmz_debug("pmz: set_termios()\n");
1272
1273 if (ZS_IS_ASLEEP(uap))
1274 return;
1275
Alan Cox606d0992006-12-08 02:38:45 -08001276 memcpy(&uap->termios_cache, termios, sizeof(struct ktermios));
Linus Torvalds1da177e2005-04-16 15:20:36 -07001277
1278 /* XXX Check which revs of machines actually allow 1 and 4Mb speeds
1279 * on the IR dongle. Note that the IRTTY driver currently doesn't know
1280 * about the FIR mode and high speed modes. So these are unused. For
1281 * implementing proper support for these, we should probably add some
1282 * DMA as well, at least on the Rx side, which isn't a simple thing
1283 * at this point.
1284 */
1285 if (ZS_IS_IRDA(uap)) {
1286 /* Calc baud rate */
1287 baud = uart_get_baud_rate(port, termios, old, 1200, 4000000);
1288 pmz_debug("pmz: switch IRDA to %ld bauds\n", baud);
1289 /* Cet the irda codec to the right rate */
1290 pmz_irda_setup(uap, &baud);
1291 /* Set final baud rate */
1292 pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
1293 pmz_load_zsregs(uap, uap->curregs);
1294 zssync(uap);
1295 } else {
1296 baud = uart_get_baud_rate(port, termios, old, 1200, 230400);
1297 pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
1298 /* Make sure modem status interrupts are correctly configured */
1299 if (UART_ENABLE_MS(&uap->port, termios->c_cflag)) {
1300 uap->curregs[R15] |= DCDIE | SYNCIE | CTSIE;
1301 uap->flags |= PMACZILOG_FLAG_MODEM_STATUS;
1302 } else {
1303 uap->curregs[R15] &= ~(DCDIE | SYNCIE | CTSIE);
1304 uap->flags &= ~PMACZILOG_FLAG_MODEM_STATUS;
1305 }
1306
1307 /* Load registers to the chip */
1308 pmz_maybe_update_regs(uap);
1309 }
1310 uart_update_timeout(port, termios->c_cflag, baud);
1311
1312 pmz_debug("pmz: set_termios() done.\n");
1313}
1314
1315/* The port lock is not held. */
Alan Cox606d0992006-12-08 02:38:45 -08001316static void pmz_set_termios(struct uart_port *port, struct ktermios *termios,
1317 struct ktermios *old)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001318{
1319 struct uart_pmac_port *uap = to_pmz(port);
1320 unsigned long flags;
1321
1322 spin_lock_irqsave(&port->lock, flags);
1323
1324 /* Disable IRQs on the port */
1325 uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
1326 write_zsreg(uap, R1, uap->curregs[R1]);
1327
1328 /* Setup new port configuration */
1329 __pmz_set_termios(port, termios, old);
1330
1331 /* Re-enable IRQs on the port */
1332 if (ZS_IS_OPEN(uap)) {
1333 uap->curregs[R1] |= INT_ALL_Rx | TxINT_ENAB;
1334 if (!ZS_IS_EXTCLK(uap))
1335 uap->curregs[R1] |= EXT_INT_ENAB;
1336 write_zsreg(uap, R1, uap->curregs[R1]);
1337 }
1338 spin_unlock_irqrestore(&port->lock, flags);
1339}
1340
1341static const char *pmz_type(struct uart_port *port)
1342{
1343 struct uart_pmac_port *uap = to_pmz(port);
1344
1345 if (ZS_IS_IRDA(uap))
1346 return "Z85c30 ESCC - Infrared port";
1347 else if (ZS_IS_INTMODEM(uap))
1348 return "Z85c30 ESCC - Internal modem";
1349 return "Z85c30 ESCC - Serial port";
1350}
1351
1352/* We do not request/release mappings of the registers here, this
1353 * happens at early serial probe time.
1354 */
1355static void pmz_release_port(struct uart_port *port)
1356{
1357}
1358
1359static int pmz_request_port(struct uart_port *port)
1360{
1361 return 0;
1362}
1363
1364/* These do not need to do anything interesting either. */
1365static void pmz_config_port(struct uart_port *port, int flags)
1366{
1367}
1368
1369/* We do not support letting the user mess with the divisor, IRQ, etc. */
1370static int pmz_verify_port(struct uart_port *port, struct serial_struct *ser)
1371{
1372 return -EINVAL;
1373}
1374
1375static struct uart_ops pmz_pops = {
1376 .tx_empty = pmz_tx_empty,
1377 .set_mctrl = pmz_set_mctrl,
1378 .get_mctrl = pmz_get_mctrl,
1379 .stop_tx = pmz_stop_tx,
1380 .start_tx = pmz_start_tx,
1381 .stop_rx = pmz_stop_rx,
1382 .enable_ms = pmz_enable_ms,
1383 .break_ctl = pmz_break_ctl,
1384 .startup = pmz_startup,
1385 .shutdown = pmz_shutdown,
1386 .set_termios = pmz_set_termios,
1387 .type = pmz_type,
1388 .release_port = pmz_release_port,
1389 .request_port = pmz_request_port,
1390 .config_port = pmz_config_port,
1391 .verify_port = pmz_verify_port,
1392};
1393
1394/*
1395 * Setup one port structure after probing, HW is down at this point,
1396 * Unlike sunzilog, we don't need to pre-init the spinlock as we don't
1397 * register our console before uart_add_one_port() is called
1398 */
1399static int __init pmz_init_port(struct uart_pmac_port *uap)
1400{
1401 struct device_node *np = uap->node;
Jeremy Kerr018a3d12006-07-12 15:40:29 +10001402 const char *conn;
1403 const struct slot_names_prop {
Linus Torvalds1da177e2005-04-16 15:20:36 -07001404 int count;
1405 char name[1];
1406 } *slots;
1407 int len;
Benjamin Herrenschmidtcc5d0182005-12-13 18:01:21 +11001408 struct resource r_ports, r_rxdma, r_txdma;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001409
1410 /*
1411 * Request & map chip registers
1412 */
Benjamin Herrenschmidtcc5d0182005-12-13 18:01:21 +11001413 if (of_address_to_resource(np, 0, &r_ports))
1414 return -ENODEV;
1415 uap->port.mapbase = r_ports.start;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001416 uap->port.membase = ioremap(uap->port.mapbase, 0x1000);
1417
1418 uap->control_reg = uap->port.membase;
1419 uap->data_reg = uap->control_reg + 0x10;
1420
1421 /*
1422 * Request & map DBDMA registers
1423 */
1424#ifdef HAS_DBDMA
Benjamin Herrenschmidtcc5d0182005-12-13 18:01:21 +11001425 if (of_address_to_resource(np, 1, &r_txdma) == 0 &&
1426 of_address_to_resource(np, 2, &r_rxdma) == 0)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001427 uap->flags |= PMACZILOG_FLAG_HAS_DMA;
Benjamin Herrenschmidtcc5d0182005-12-13 18:01:21 +11001428#else
1429 memset(&r_txdma, 0, sizeof(struct resource));
1430 memset(&r_rxdma, 0, sizeof(struct resource));
Linus Torvalds1da177e2005-04-16 15:20:36 -07001431#endif
1432 if (ZS_HAS_DMA(uap)) {
Benjamin Herrenschmidtcc5d0182005-12-13 18:01:21 +11001433 uap->tx_dma_regs = ioremap(r_txdma.start, 0x100);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001434 if (uap->tx_dma_regs == NULL) {
1435 uap->flags &= ~PMACZILOG_FLAG_HAS_DMA;
1436 goto no_dma;
1437 }
Benjamin Herrenschmidtcc5d0182005-12-13 18:01:21 +11001438 uap->rx_dma_regs = ioremap(r_rxdma.start, 0x100);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001439 if (uap->rx_dma_regs == NULL) {
1440 iounmap(uap->tx_dma_regs);
1441 uap->tx_dma_regs = NULL;
1442 uap->flags &= ~PMACZILOG_FLAG_HAS_DMA;
1443 goto no_dma;
1444 }
Benjamin Herrenschmidt0ebfff12006-07-03 21:36:01 +10001445 uap->tx_dma_irq = irq_of_parse_and_map(np, 1);
1446 uap->rx_dma_irq = irq_of_parse_and_map(np, 2);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001447 }
1448no_dma:
1449
1450 /*
1451 * Detect port type
1452 */
Stephen Rothwell55b61fe2007-05-03 17:26:52 +10001453 if (of_device_is_compatible(np, "cobalt"))
Linus Torvalds1da177e2005-04-16 15:20:36 -07001454 uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
Stephen Rothwell40cd3a42007-05-01 13:54:02 +10001455 conn = of_get_property(np, "AAPL,connector", &len);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001456 if (conn && (strcmp(conn, "infrared") == 0))
1457 uap->flags |= PMACZILOG_FLAG_IS_IRDA;
1458 uap->port_type = PMAC_SCC_ASYNC;
1459 /* 1999 Powerbook G3 has slot-names property instead */
Stephen Rothwell40cd3a42007-05-01 13:54:02 +10001460 slots = of_get_property(np, "slot-names", &len);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001461 if (slots && slots->count > 0) {
1462 if (strcmp(slots->name, "IrDA") == 0)
1463 uap->flags |= PMACZILOG_FLAG_IS_IRDA;
1464 else if (strcmp(slots->name, "Modem") == 0)
1465 uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
1466 }
1467 if (ZS_IS_IRDA(uap))
1468 uap->port_type = PMAC_SCC_IRDA;
1469 if (ZS_IS_INTMODEM(uap)) {
Stephen Rothwell30686ba2007-04-24 13:53:04 +10001470 struct device_node* i2c_modem =
1471 of_find_node_by_name(NULL, "i2c-modem");
Linus Torvalds1da177e2005-04-16 15:20:36 -07001472 if (i2c_modem) {
Jeremy Kerr018a3d12006-07-12 15:40:29 +10001473 const char* mid =
Stephen Rothwell40cd3a42007-05-01 13:54:02 +10001474 of_get_property(i2c_modem, "modem-id", NULL);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001475 if (mid) switch(*mid) {
1476 case 0x04 :
1477 case 0x05 :
1478 case 0x07 :
1479 case 0x08 :
1480 case 0x0b :
1481 case 0x0c :
1482 uap->port_type = PMAC_SCC_I2S1;
1483 }
1484 printk(KERN_INFO "pmac_zilog: i2c-modem detected, id: %d\n",
1485 mid ? (*mid) : 0);
Stephen Rothwell30686ba2007-04-24 13:53:04 +10001486 of_node_put(i2c_modem);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001487 } else {
1488 printk(KERN_INFO "pmac_zilog: serial modem detected\n");
1489 }
1490 }
1491
1492 /*
1493 * Init remaining bits of "port" structure
1494 */
Russell King9b4a1612006-02-05 10:48:10 +00001495 uap->port.iotype = UPIO_MEM;
Benjamin Herrenschmidt0ebfff12006-07-03 21:36:01 +10001496 uap->port.irq = irq_of_parse_and_map(np, 0);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001497 uap->port.uartclk = ZS_CLOCK;
1498 uap->port.fifosize = 1;
1499 uap->port.ops = &pmz_pops;
1500 uap->port.type = PORT_PMAC_ZILOG;
1501 uap->port.flags = 0;
1502
1503 /* Setup some valid baud rate information in the register
1504 * shadows so we don't write crap there before baud rate is
1505 * first initialized.
1506 */
1507 pmz_convert_to_zs(uap, CS8, 0, 9600);
1508
1509 return 0;
1510}
1511
1512/*
1513 * Get rid of a port on module removal
1514 */
1515static void pmz_dispose_port(struct uart_pmac_port *uap)
1516{
1517 struct device_node *np;
1518
1519 np = uap->node;
1520 iounmap(uap->rx_dma_regs);
1521 iounmap(uap->tx_dma_regs);
1522 iounmap(uap->control_reg);
1523 uap->node = NULL;
1524 of_node_put(np);
1525 memset(uap, 0, sizeof(struct uart_pmac_port));
1526}
1527
1528/*
1529 * Called upon match with an escc node in the devive-tree.
1530 */
Jeff Mahoney5e655772005-07-06 15:44:41 -04001531static int pmz_attach(struct macio_dev *mdev, const struct of_device_id *match)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001532{
1533 int i;
1534
1535 /* Iterate the pmz_ports array to find a matching entry
1536 */
1537 for (i = 0; i < MAX_ZS_PORTS; i++)
1538 if (pmz_ports[i].node == mdev->ofdev.node) {
1539 struct uart_pmac_port *uap = &pmz_ports[i];
1540
1541 uap->dev = mdev;
1542 dev_set_drvdata(&mdev->ofdev.dev, uap);
1543 if (macio_request_resources(uap->dev, "pmac_zilog"))
1544 printk(KERN_WARNING "%s: Failed to request resource"
1545 ", port still active\n",
1546 uap->node->name);
1547 else
1548 uap->flags |= PMACZILOG_FLAG_RSRC_REQUESTED;
1549 return 0;
1550 }
1551 return -ENODEV;
1552}
1553
1554/*
1555 * That one should not be called, macio isn't really a hotswap device,
1556 * we don't expect one of those serial ports to go away...
1557 */
1558static int pmz_detach(struct macio_dev *mdev)
1559{
1560 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1561
1562 if (!uap)
1563 return -ENODEV;
1564
1565 if (uap->flags & PMACZILOG_FLAG_RSRC_REQUESTED) {
1566 macio_release_resources(uap->dev);
1567 uap->flags &= ~PMACZILOG_FLAG_RSRC_REQUESTED;
1568 }
1569 dev_set_drvdata(&mdev->ofdev.dev, NULL);
1570 uap->dev = NULL;
1571
1572 return 0;
1573}
1574
1575
Pavel Machek0370aff2005-04-16 15:25:35 -07001576static int pmz_suspend(struct macio_dev *mdev, pm_message_t pm_state)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001577{
1578 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1579 struct uart_state *state;
1580 unsigned long flags;
1581
1582 if (uap == NULL) {
1583 printk("HRM... pmz_suspend with NULL uap\n");
1584 return 0;
1585 }
1586
Pavel Machekca078ba2005-09-03 15:56:57 -07001587 if (pm_state.event == mdev->ofdev.dev.power.power_state.event)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001588 return 0;
1589
1590 pmz_debug("suspend, switching to state %d\n", pm_state);
1591
1592 state = pmz_uart_reg.state + uap->port.line;
1593
Arjan van de Venf392ecf2006-01-12 18:44:32 +00001594 mutex_lock(&pmz_irq_mutex);
Ingo Molnare2862f62006-01-13 21:37:07 +00001595 mutex_lock(&state->mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001596
1597 spin_lock_irqsave(&uap->port.lock, flags);
1598
1599 if (ZS_IS_OPEN(uap) || ZS_IS_CONS(uap)) {
1600 /* Disable receiver and transmitter. */
1601 uap->curregs[R3] &= ~RxENABLE;
1602 uap->curregs[R5] &= ~TxENABLE;
1603
1604 /* Disable all interrupts and BRK assertion. */
1605 uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
1606 uap->curregs[R5] &= ~SND_BRK;
1607 pmz_load_zsregs(uap, uap->curregs);
1608 uap->flags |= PMACZILOG_FLAG_IS_ASLEEP;
1609 mb();
1610 }
1611
1612 spin_unlock_irqrestore(&uap->port.lock, flags);
1613
1614 if (ZS_IS_OPEN(uap) || ZS_IS_OPEN(uap->mate))
1615 if (ZS_IS_ASLEEP(uap->mate) && ZS_IS_IRQ_ON(pmz_get_port_A(uap))) {
1616 pmz_get_port_A(uap)->flags &= ~PMACZILOG_FLAG_IS_IRQ_ON;
1617 disable_irq(uap->port.irq);
1618 }
1619
1620 if (ZS_IS_CONS(uap))
1621 uap->port.cons->flags &= ~CON_ENABLED;
1622
1623 /* Shut the chip down */
1624 pmz_set_scc_power(uap, 0);
1625
Ingo Molnare2862f62006-01-13 21:37:07 +00001626 mutex_unlock(&state->mutex);
Arjan van de Venf392ecf2006-01-12 18:44:32 +00001627 mutex_unlock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001628
1629 pmz_debug("suspend, switching complete\n");
1630
1631 mdev->ofdev.dev.power.power_state = pm_state;
1632
1633 return 0;
1634}
1635
1636
1637static int pmz_resume(struct macio_dev *mdev)
1638{
1639 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1640 struct uart_state *state;
1641 unsigned long flags;
1642 int pwr_delay = 0;
1643
1644 if (uap == NULL)
1645 return 0;
1646
Pavel Machekca078ba2005-09-03 15:56:57 -07001647 if (mdev->ofdev.dev.power.power_state.event == PM_EVENT_ON)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001648 return 0;
1649
1650 pmz_debug("resume, switching to state 0\n");
1651
1652 state = pmz_uart_reg.state + uap->port.line;
1653
Arjan van de Venf392ecf2006-01-12 18:44:32 +00001654 mutex_lock(&pmz_irq_mutex);
Ingo Molnare2862f62006-01-13 21:37:07 +00001655 mutex_lock(&state->mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001656
1657 spin_lock_irqsave(&uap->port.lock, flags);
1658 if (!ZS_IS_OPEN(uap) && !ZS_IS_CONS(uap)) {
1659 spin_unlock_irqrestore(&uap->port.lock, flags);
1660 goto bail;
1661 }
1662 pwr_delay = __pmz_startup(uap);
1663
1664 /* Take care of config that may have changed while asleep */
1665 __pmz_set_termios(&uap->port, &uap->termios_cache, NULL);
1666
1667 if (ZS_IS_OPEN(uap)) {
1668 /* Enable interrupts */
1669 uap->curregs[R1] |= INT_ALL_Rx | TxINT_ENAB;
1670 if (!ZS_IS_EXTCLK(uap))
1671 uap->curregs[R1] |= EXT_INT_ENAB;
1672 write_zsreg(uap, R1, uap->curregs[R1]);
1673 }
1674
1675 spin_unlock_irqrestore(&uap->port.lock, flags);
1676
1677 if (ZS_IS_CONS(uap))
1678 uap->port.cons->flags |= CON_ENABLED;
1679
1680 /* Re-enable IRQ on the controller */
1681 if (ZS_IS_OPEN(uap) && !ZS_IS_IRQ_ON(pmz_get_port_A(uap))) {
1682 pmz_get_port_A(uap)->flags |= PMACZILOG_FLAG_IS_IRQ_ON;
1683 enable_irq(uap->port.irq);
1684 }
1685
1686 bail:
Ingo Molnare2862f62006-01-13 21:37:07 +00001687 mutex_unlock(&state->mutex);
Arjan van de Venf392ecf2006-01-12 18:44:32 +00001688 mutex_unlock(&pmz_irq_mutex);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001689
1690 /* Right now, we deal with delay by blocking here, I'll be
1691 * smarter later on
1692 */
1693 if (pwr_delay != 0) {
1694 pmz_debug("pmz: delaying %d ms\n", pwr_delay);
1695 msleep(pwr_delay);
1696 }
1697
1698 pmz_debug("resume, switching complete\n");
1699
Pavel Machekca078ba2005-09-03 15:56:57 -07001700 mdev->ofdev.dev.power.power_state.event = PM_EVENT_ON;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001701
1702 return 0;
1703}
1704
1705/*
1706 * Probe all ports in the system and build the ports array, we register
1707 * with the serial layer at this point, the macio-type probing is only
1708 * used later to "attach" to the sysfs tree so we get power management
1709 * events
1710 */
1711static int __init pmz_probe(void)
1712{
1713 struct device_node *node_p, *node_a, *node_b, *np;
1714 int count = 0;
1715 int rc;
1716
1717 /*
1718 * Find all escc chips in the system
1719 */
1720 node_p = of_find_node_by_name(NULL, "escc");
1721 while (node_p) {
1722 /*
1723 * First get channel A/B node pointers
1724 *
1725 * TODO: Add routines with proper locking to do that...
1726 */
1727 node_a = node_b = NULL;
1728 for (np = NULL; (np = of_get_next_child(node_p, np)) != NULL;) {
1729 if (strncmp(np->name, "ch-a", 4) == 0)
1730 node_a = of_node_get(np);
1731 else if (strncmp(np->name, "ch-b", 4) == 0)
1732 node_b = of_node_get(np);
1733 }
1734 if (!node_a && !node_b) {
1735 of_node_put(node_a);
1736 of_node_put(node_b);
1737 printk(KERN_ERR "pmac_zilog: missing node %c for escc %s\n",
1738 (!node_a) ? 'a' : 'b', node_p->full_name);
1739 goto next;
1740 }
1741
1742 /*
1743 * Fill basic fields in the port structures
1744 */
1745 pmz_ports[count].mate = &pmz_ports[count+1];
1746 pmz_ports[count+1].mate = &pmz_ports[count];
1747 pmz_ports[count].flags = PMACZILOG_FLAG_IS_CHANNEL_A;
1748 pmz_ports[count].node = node_a;
1749 pmz_ports[count+1].node = node_b;
1750 pmz_ports[count].port.line = count;
1751 pmz_ports[count+1].port.line = count+1;
1752
1753 /*
1754 * Setup the ports for real
1755 */
1756 rc = pmz_init_port(&pmz_ports[count]);
1757 if (rc == 0 && node_b != NULL)
1758 rc = pmz_init_port(&pmz_ports[count+1]);
1759 if (rc != 0) {
1760 of_node_put(node_a);
1761 of_node_put(node_b);
1762 memset(&pmz_ports[count], 0, sizeof(struct uart_pmac_port));
1763 memset(&pmz_ports[count+1], 0, sizeof(struct uart_pmac_port));
1764 goto next;
1765 }
1766 count += 2;
1767next:
1768 node_p = of_find_node_by_name(node_p, "escc");
1769 }
1770 pmz_ports_count = count;
1771
1772 return 0;
1773}
1774
1775#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
1776
1777static void pmz_console_write(struct console *con, const char *s, unsigned int count);
1778static int __init pmz_console_setup(struct console *co, char *options);
1779
1780static struct console pmz_console = {
1781 .name = "ttyS",
1782 .write = pmz_console_write,
1783 .device = uart_console_device,
1784 .setup = pmz_console_setup,
1785 .flags = CON_PRINTBUFFER,
1786 .index = -1,
1787 .data = &pmz_uart_reg,
1788};
1789
1790#define PMACZILOG_CONSOLE &pmz_console
1791#else /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
1792#define PMACZILOG_CONSOLE (NULL)
1793#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
1794
1795/*
1796 * Register the driver, console driver and ports with the serial
1797 * core
1798 */
1799static int __init pmz_register(void)
1800{
1801 int i, rc;
1802
1803 pmz_uart_reg.nr = pmz_ports_count;
1804 pmz_uart_reg.cons = PMACZILOG_CONSOLE;
1805 pmz_uart_reg.minor = 64;
1806
1807 /*
1808 * Register this driver with the serial core
1809 */
1810 rc = uart_register_driver(&pmz_uart_reg);
1811 if (rc)
1812 return rc;
1813
1814 /*
1815 * Register each port with the serial core
1816 */
1817 for (i = 0; i < pmz_ports_count; i++) {
1818 struct uart_pmac_port *uport = &pmz_ports[i];
1819 /* NULL node may happen on wallstreet */
1820 if (uport->node != NULL)
1821 rc = uart_add_one_port(&pmz_uart_reg, &uport->port);
1822 if (rc)
1823 goto err_out;
1824 }
1825
1826 return 0;
1827err_out:
1828 while (i-- > 0) {
1829 struct uart_pmac_port *uport = &pmz_ports[i];
1830 uart_remove_one_port(&pmz_uart_reg, &uport->port);
1831 }
1832 uart_unregister_driver(&pmz_uart_reg);
1833 return rc;
1834}
1835
Jeff Mahoney5e655772005-07-06 15:44:41 -04001836static struct of_device_id pmz_match[] =
Linus Torvalds1da177e2005-04-16 15:20:36 -07001837{
1838 {
1839 .name = "ch-a",
Linus Torvalds1da177e2005-04-16 15:20:36 -07001840 },
1841 {
1842 .name = "ch-b",
Linus Torvalds1da177e2005-04-16 15:20:36 -07001843 },
1844 {},
1845};
Jeff Mahoney5e655772005-07-06 15:44:41 -04001846MODULE_DEVICE_TABLE (of, pmz_match);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001847
1848static struct macio_driver pmz_driver =
1849{
1850 .name = "pmac_zilog",
1851 .match_table = pmz_match,
1852 .probe = pmz_attach,
1853 .remove = pmz_detach,
1854 .suspend = pmz_suspend,
1855 .resume = pmz_resume,
1856};
1857
1858static int __init init_pmz(void)
1859{
1860 int rc, i;
1861 printk(KERN_INFO "%s\n", version);
1862
1863 /*
1864 * First, we need to do a direct OF-based probe pass. We
1865 * do that because we want serial console up before the
1866 * macio stuffs calls us back, and since that makes it
1867 * easier to pass the proper number of channels to
1868 * uart_register_driver()
1869 */
1870 if (pmz_ports_count == 0)
1871 pmz_probe();
1872
1873 /*
1874 * Bail early if no port found
1875 */
1876 if (pmz_ports_count == 0)
1877 return -ENODEV;
1878
1879 /*
1880 * Now we register with the serial layer
1881 */
1882 rc = pmz_register();
1883 if (rc) {
1884 printk(KERN_ERR
1885 "pmac_zilog: Error registering serial device, disabling pmac_zilog.\n"
1886 "pmac_zilog: Did another serial driver already claim the minors?\n");
1887 /* effectively "pmz_unprobe()" */
1888 for (i=0; i < pmz_ports_count; i++)
1889 pmz_dispose_port(&pmz_ports[i]);
1890 return rc;
1891 }
1892
1893 /*
1894 * Then we register the macio driver itself
1895 */
1896 return macio_register_driver(&pmz_driver);
1897}
1898
1899static void __exit exit_pmz(void)
1900{
1901 int i;
1902
1903 /* Get rid of macio-driver (detach from macio) */
1904 macio_unregister_driver(&pmz_driver);
1905
1906 for (i = 0; i < pmz_ports_count; i++) {
1907 struct uart_pmac_port *uport = &pmz_ports[i];
1908 if (uport->node != NULL) {
1909 uart_remove_one_port(&pmz_uart_reg, &uport->port);
1910 pmz_dispose_port(uport);
1911 }
1912 }
1913 /* Unregister UART driver */
1914 uart_unregister_driver(&pmz_uart_reg);
1915}
1916
1917#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
1918
Russell Kingd3587882006-03-20 20:00:09 +00001919static void pmz_console_putchar(struct uart_port *port, int ch)
1920{
1921 struct uart_pmac_port *uap = (struct uart_pmac_port *)port;
1922
1923 /* Wait for the transmit buffer to empty. */
1924 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0)
1925 udelay(5);
1926 write_zsdata(uap, ch);
1927}
1928
Linus Torvalds1da177e2005-04-16 15:20:36 -07001929/*
1930 * Print a string to the serial port trying not to disturb
1931 * any possible real use of the port...
1932 */
1933static void pmz_console_write(struct console *con, const char *s, unsigned int count)
1934{
1935 struct uart_pmac_port *uap = &pmz_ports[con->index];
1936 unsigned long flags;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001937
1938 if (ZS_IS_ASLEEP(uap))
1939 return;
1940 spin_lock_irqsave(&uap->port.lock, flags);
1941
1942 /* Turn of interrupts and enable the transmitter. */
1943 write_zsreg(uap, R1, uap->curregs[1] & ~TxINT_ENAB);
1944 write_zsreg(uap, R5, uap->curregs[5] | TxENABLE | RTS | DTR);
1945
Russell Kingd3587882006-03-20 20:00:09 +00001946 uart_console_write(&uap->port, s, count, pmz_console_putchar);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001947
1948 /* Restore the values in the registers. */
1949 write_zsreg(uap, R1, uap->curregs[1]);
1950 /* Don't disable the transmitter. */
1951
1952 spin_unlock_irqrestore(&uap->port.lock, flags);
1953}
1954
1955/*
1956 * Setup the serial console
1957 */
1958static int __init pmz_console_setup(struct console *co, char *options)
1959{
1960 struct uart_pmac_port *uap;
1961 struct uart_port *port;
1962 int baud = 38400;
1963 int bits = 8;
1964 int parity = 'n';
1965 int flow = 'n';
1966 unsigned long pwr_delay;
1967
1968 /*
1969 * XServe's default to 57600 bps
1970 */
1971 if (machine_is_compatible("RackMac1,1")
1972 || machine_is_compatible("RackMac1,2")
1973 || machine_is_compatible("MacRISC4"))
1974 baud = 57600;
1975
1976 /*
1977 * Check whether an invalid uart number has been specified, and
1978 * if so, search for the first available port that does have
1979 * console support.
1980 */
1981 if (co->index >= pmz_ports_count)
1982 co->index = 0;
1983 uap = &pmz_ports[co->index];
1984 if (uap->node == NULL)
1985 return -ENODEV;
1986 port = &uap->port;
1987
1988 /*
1989 * Mark port as beeing a console
1990 */
1991 uap->flags |= PMACZILOG_FLAG_IS_CONS;
1992
1993 /*
1994 * Temporary fix for uart layer who didn't setup the spinlock yet
1995 */
1996 spin_lock_init(&port->lock);
1997
1998 /*
1999 * Enable the hardware
2000 */
2001 pwr_delay = __pmz_startup(uap);
2002 if (pwr_delay)
2003 mdelay(pwr_delay);
2004
2005 if (options)
2006 uart_parse_options(options, &baud, &parity, &bits, &flow);
2007
2008 return uart_set_options(port, co, baud, parity, bits, flow);
2009}
2010
2011static int __init pmz_console_init(void)
2012{
2013 /* Probe ports */
2014 pmz_probe();
2015
2016 /* TODO: Autoprobe console based on OF */
2017 /* pmz_console.index = i; */
2018 register_console(&pmz_console);
2019
2020 return 0;
2021
2022}
2023console_initcall(pmz_console_init);
2024#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
2025
2026module_init(init_pmz);
2027module_exit(exit_pmz);