Ben Dooks | d58153d | 2007-07-22 16:07:09 +0100 | [diff] [blame^] | 1 | # arch/arm/plat-s3c/Kconfig |
| 2 | # |
| 3 | # Copyright 2007 Simtec Electronics |
| 4 | # |
| 5 | # Licensed under GPLv2 |
| 6 | |
| 7 | config PLAT_S3C |
| 8 | bool |
| 9 | depends on ARCH_S3C2410 |
| 10 | default y if ARCH_S3C2410 |
| 11 | select NO_IOPORT |
| 12 | help |
| 13 | Base platform code for any Samsung S3C device |
| 14 | |
| 15 | comment "Boot options" |
| 16 | |
| 17 | config S3C2410_BOOT_WATCHDOG |
| 18 | bool "S3C2410 Initialisation watchdog" |
| 19 | depends on PLAT_S3C && S3C2410_WATCHDOG |
| 20 | help |
| 21 | Say y to enable the watchdog during the kernel decompression |
| 22 | stage. If the kernel fails to uncompress, then the watchdog |
| 23 | will trigger a reset and the system should restart. |
| 24 | |
| 25 | config S3C2410_BOOT_ERROR_RESET |
| 26 | bool "S3C2410 Reboot on decompression error" |
| 27 | depends on PLAT_S3C |
| 28 | help |
| 29 | Say y here to use the watchdog to reset the system if the |
| 30 | kernel decompressor detects an error during decompression. |
| 31 | |
| 32 | comment "Power management" |
| 33 | |
| 34 | config S3C2410_PM_DEBUG |
| 35 | bool "S3C2410 PM Suspend debug" |
| 36 | depends on PLAT_S3C && PM |
| 37 | help |
| 38 | Say Y here if you want verbose debugging from the PM Suspend and |
| 39 | Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
| 40 | for more information. |
| 41 | |
| 42 | config S3C2410_PM_CHECK |
| 43 | bool "S3C2410 PM Suspend Memory CRC" |
| 44 | depends on PLAT_S3C && PM && CRC32 |
| 45 | help |
| 46 | Enable the PM code's memory area checksum over sleep. This option |
| 47 | will generate CRCs of all blocks of memory, and store them before |
| 48 | going to sleep. The blocks are then checked on resume for any |
| 49 | errors. |
| 50 | |
| 51 | Note, this can take several seconds depending on memory size |
| 52 | and CPU speed. |
| 53 | |
| 54 | See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
| 55 | |
| 56 | config S3C2410_PM_CHECK_CHUNKSIZE |
| 57 | int "S3C2410 PM Suspend CRC Chunksize (KiB)" |
| 58 | depends on PLAT_S3C && PM && S3C2410_PM_CHECK |
| 59 | default 64 |
| 60 | help |
| 61 | Set the chunksize in Kilobytes of the CRC for checking memory |
| 62 | corruption over suspend and resume. A smaller value will mean that |
| 63 | the CRC data block will take more memory, but wil identify any |
| 64 | faults with better precision. |
| 65 | |
| 66 | See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
| 67 | |
| 68 | config S3C2410_LOWLEVEL_UART_PORT |
| 69 | int "S3C2410 UART to use for low-level messages" |
| 70 | depends on PLAT_S3C |
| 71 | default 0 |
| 72 | help |
| 73 | Choice of which UART port to use for the low-level messages, |
| 74 | such as the `Uncompressing...` at start time. The value of |
| 75 | this configuration should be between zero and two. The port |
| 76 | must have been initialised by the boot-loader before use. |