blob: acb636963e90724c05792425ed7290493c1a97aa [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*****************************************************************************/
2
3/*
4 * baycom_par.c -- baycom par96 and picpar radio modem driver.
5 *
6 * Copyright (C) 1996-2000 Thomas Sailer (sailer@ife.ee.ethz.ch)
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License as published by
10 * the Free Software Foundation; either version 2 of the License, or
11 * (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21 *
22 * Please note that the GPL allows you to use the driver, NOT the radio.
23 * In order to use the radio, you need a license from the communications
24 * authority of your country.
25 *
26 *
27 * Supported modems
28 *
29 * par96: This is a modem for 9600 baud FSK compatible to the G3RUH standard.
30 * The modem does all the filtering and regenerates the receiver clock.
31 * Data is transferred from and to the PC via a shift register.
32 * The shift register is filled with 16 bits and an interrupt is
33 * signalled. The PC then empties the shift register in a burst. This
34 * modem connects to the parallel port, hence the name. The modem
35 * leaves the implementation of the HDLC protocol and the scrambler
36 * polynomial to the PC. This modem is no longer available (at least
37 * from Baycom) and has been replaced by the PICPAR modem (see below).
38 * You may however still build one from the schematics published in
39 * cq-DL :-).
40 *
41 * picpar: This is a redesign of the par96 modem by Henning Rech, DF9IC. The
42 * modem is protocol compatible to par96, but uses only three low
43 * power ICs and can therefore be fed from the parallel port and
44 * does not require an additional power supply. It features
45 * built in DCD circuitry. The driver should therefore be configured
46 * for hardware DCD.
47 *
48 *
49 * Command line options (insmod command line)
50 *
51 * mode driver mode string. Valid choices are par96 and picpar.
52 * iobase base address of the port; common values are 0x378, 0x278, 0x3bc
53 *
54 *
55 * History:
56 * 0.1 26.06.1996 Adapted from baycom.c and made network driver interface
57 * 18.10.1996 Changed to new user space access routines (copy_{to,from}_user)
58 * 0.3 26.04.1997 init code/data tagged
59 * 0.4 08.07.1997 alternative ser12 decoding algorithm (uses delta CTS ints)
60 * 0.5 11.11.1997 split into separate files for ser12/par96
61 * 0.6 03.08.1999 adapt to Linus' new __setup/__initcall
62 * removed some pre-2.2 kernel compatibility cruft
63 * 0.7 10.08.1999 Check if parport can do SPP and is safe to access during interrupt contexts
64 * 0.8 12.02.2000 adapted to softnet driver interface
65 * removed direct parport access, uses parport driver methods
66 * 0.9 03.07.2000 fix interface name handling
67 */
68
69/*****************************************************************************/
70
71#include <linux/module.h>
72#include <linux/kernel.h>
73#include <linux/types.h>
74#include <linux/fcntl.h>
75#include <linux/interrupt.h>
76#include <linux/ioport.h>
77#include <linux/in.h>
78#include <linux/string.h>
79#include <linux/init.h>
80#include <linux/delay.h>
81#include <linux/errno.h>
82#include <linux/netdevice.h>
83#include <linux/hdlcdrv.h>
84#include <linux/baycom.h>
85#include <linux/parport.h>
86#include <linux/bitops.h>
Marcelo Feitoza Parisicd8749b2005-07-15 11:16:42 +010087#include <linux/jiffies.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070088
Linus Torvalds1da177e2005-04-16 15:20:36 -070089#include <asm/uaccess.h>
90
91/* --------------------------------------------------------------------- */
92
93#define BAYCOM_DEBUG
94
95/*
96 * modem options; bit mask
97 */
98#define BAYCOM_OPTIONS_SOFTDCD 1
99
100/* --------------------------------------------------------------------- */
101
102static const char bc_drvname[] = "baycom_par";
103static const char bc_drvinfo[] = KERN_INFO "baycom_par: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA\n"
Michal Marekc1afba32011-04-01 12:41:20 +0200104"baycom_par: version 0.9\n";
Linus Torvalds1da177e2005-04-16 15:20:36 -0700105
106/* --------------------------------------------------------------------- */
107
108#define NR_PORTS 4
109
110static struct net_device *baycom_device[NR_PORTS];
111
112/* --------------------------------------------------------------------- */
113
114#define PAR96_BURSTBITS 16
115#define PAR96_BURST 4
116#define PAR96_PTT 2
117#define PAR96_TXBIT 1
118#define PAR96_ACK 0x40
119#define PAR96_RXBIT 0x20
120#define PAR96_DCD 0x10
121#define PAR97_POWER 0xf8
122
123/* ---------------------------------------------------------------------- */
124/*
125 * Information that need to be kept for each board.
126 */
127
128struct baycom_state {
129 struct hdlcdrv_state hdrv;
130
131 struct pardevice *pdev;
132 unsigned int options;
133
134 struct modem_state {
135 short arb_divider;
136 unsigned char flags;
137 unsigned int shreg;
138 struct modem_state_par96 {
139 int dcd_count;
140 unsigned int dcd_shreg;
141 unsigned long descram;
142 unsigned long scram;
143 } par96;
144 } modem;
145
146#ifdef BAYCOM_DEBUG
147 struct debug_vals {
148 unsigned long last_jiffies;
149 unsigned cur_intcnt;
150 unsigned last_intcnt;
151 int cur_pllcorr;
152 int last_pllcorr;
153 } debug_vals;
154#endif /* BAYCOM_DEBUG */
155};
156
157/* --------------------------------------------------------------------- */
158
159static void __inline__ baycom_int_freq(struct baycom_state *bc)
160{
161#ifdef BAYCOM_DEBUG
162 unsigned long cur_jiffies = jiffies;
163 /*
164 * measure the interrupt frequency
165 */
166 bc->debug_vals.cur_intcnt++;
Marcelo Feitoza Parisicd8749b2005-07-15 11:16:42 +0100167 if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700168 bc->debug_vals.last_jiffies = cur_jiffies;
169 bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
170 bc->debug_vals.cur_intcnt = 0;
171 bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr;
172 bc->debug_vals.cur_pllcorr = 0;
173 }
174#endif /* BAYCOM_DEBUG */
175}
176
177/* --------------------------------------------------------------------- */
178/*
179 * ===================== PAR96 specific routines =========================
180 */
181
182#define PAR96_DESCRAM_TAP1 0x20000
183#define PAR96_DESCRAM_TAP2 0x01000
184#define PAR96_DESCRAM_TAP3 0x00001
185
186#define PAR96_DESCRAM_TAPSH1 17
187#define PAR96_DESCRAM_TAPSH2 12
188#define PAR96_DESCRAM_TAPSH3 0
189
190#define PAR96_SCRAM_TAP1 0x20000 /* X^17 */
191#define PAR96_SCRAM_TAPN 0x00021 /* X^0+X^5 */
192
193/* --------------------------------------------------------------------- */
194
195static __inline__ void par96_tx(struct net_device *dev, struct baycom_state *bc)
196{
197 int i;
198 unsigned int data = hdlcdrv_getbits(&bc->hdrv);
199 struct parport *pp = bc->pdev->port;
200
201 for(i = 0; i < PAR96_BURSTBITS; i++, data >>= 1) {
202 unsigned char val = PAR97_POWER;
203 bc->modem.par96.scram = ((bc->modem.par96.scram << 1) |
204 (bc->modem.par96.scram & 1));
205 if (!(data & 1))
206 bc->modem.par96.scram ^= 1;
207 if (bc->modem.par96.scram & (PAR96_SCRAM_TAP1 << 1))
208 bc->modem.par96.scram ^=
209 (PAR96_SCRAM_TAPN << 1);
210 if (bc->modem.par96.scram & (PAR96_SCRAM_TAP1 << 2))
211 val |= PAR96_TXBIT;
212 pp->ops->write_data(pp, val);
213 pp->ops->write_data(pp, val | PAR96_BURST);
214 }
215}
216
217/* --------------------------------------------------------------------- */
218
219static __inline__ void par96_rx(struct net_device *dev, struct baycom_state *bc)
220{
221 int i;
222 unsigned int data, mask, mask2, descx;
223 struct parport *pp = bc->pdev->port;
224
225 /*
226 * do receiver; differential decode and descramble on the fly
227 */
228 for(data = i = 0; i < PAR96_BURSTBITS; i++) {
229 bc->modem.par96.descram = (bc->modem.par96.descram << 1);
230 if (pp->ops->read_status(pp) & PAR96_RXBIT)
231 bc->modem.par96.descram |= 1;
232 descx = bc->modem.par96.descram ^
233 (bc->modem.par96.descram >> 1);
234 /* now the diff decoded data is inverted in descram */
235 pp->ops->write_data(pp, PAR97_POWER | PAR96_PTT);
236 descx ^= ((descx >> PAR96_DESCRAM_TAPSH1) ^
237 (descx >> PAR96_DESCRAM_TAPSH2));
238 data >>= 1;
239 if (!(descx & 1))
240 data |= 0x8000;
241 pp->ops->write_data(pp, PAR97_POWER | PAR96_PTT | PAR96_BURST);
242 }
243 hdlcdrv_putbits(&bc->hdrv, data);
244 /*
245 * do DCD algorithm
246 */
247 if (bc->options & BAYCOM_OPTIONS_SOFTDCD) {
248 bc->modem.par96.dcd_shreg = (bc->modem.par96.dcd_shreg >> 16)
249 | (data << 16);
250 /* search for flags and set the dcd counter appropriately */
251 for(mask = 0x1fe00, mask2 = 0xfc00, i = 0;
252 i < PAR96_BURSTBITS; i++, mask <<= 1, mask2 <<= 1)
253 if ((bc->modem.par96.dcd_shreg & mask) == mask2)
254 bc->modem.par96.dcd_count = HDLCDRV_MAXFLEN+4;
255 /* check for abort/noise sequences */
256 for(mask = 0x1fe00, mask2 = 0x1fe00, i = 0;
257 i < PAR96_BURSTBITS; i++, mask <<= 1, mask2 <<= 1)
258 if (((bc->modem.par96.dcd_shreg & mask) == mask2) &&
259 (bc->modem.par96.dcd_count >= 0))
260 bc->modem.par96.dcd_count -= HDLCDRV_MAXFLEN-10;
261 /* decrement and set the dcd variable */
262 if (bc->modem.par96.dcd_count >= 0)
263 bc->modem.par96.dcd_count -= 2;
264 hdlcdrv_setdcd(&bc->hdrv, bc->modem.par96.dcd_count > 0);
265 } else {
266 hdlcdrv_setdcd(&bc->hdrv, !!(pp->ops->read_status(pp) & PAR96_DCD));
267 }
268}
269
270/* --------------------------------------------------------------------- */
271
Jeff Garzik5712cb32007-10-19 02:54:26 -0400272static void par96_interrupt(void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700273{
Jeff Garzik5712cb32007-10-19 02:54:26 -0400274 struct net_device *dev = dev_id;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700275 struct baycom_state *bc = netdev_priv(dev);
276
277 baycom_int_freq(bc);
278 /*
279 * check if transmitter active
280 */
281 if (hdlcdrv_ptt(&bc->hdrv))
282 par96_tx(dev, bc);
283 else {
284 par96_rx(dev, bc);
285 if (--bc->modem.arb_divider <= 0) {
286 bc->modem.arb_divider = 6;
287 local_irq_enable();
288 hdlcdrv_arbitrate(dev, &bc->hdrv);
289 }
290 }
291 local_irq_enable();
292 hdlcdrv_transmitter(dev, &bc->hdrv);
293 hdlcdrv_receiver(dev, &bc->hdrv);
294 local_irq_disable();
295}
296
297/* --------------------------------------------------------------------- */
298
299static void par96_wakeup(void *handle)
300{
301 struct net_device *dev = (struct net_device *)handle;
302 struct baycom_state *bc = netdev_priv(dev);
303
304 printk(KERN_DEBUG "baycom_par: %s: why am I being woken up?\n", dev->name);
305 if (!parport_claim(bc->pdev))
306 printk(KERN_DEBUG "baycom_par: %s: I'm broken.\n", dev->name);
307}
308
309/* --------------------------------------------------------------------- */
310
311static int par96_open(struct net_device *dev)
312{
313 struct baycom_state *bc = netdev_priv(dev);
314 struct parport *pp;
315
316 if (!dev || !bc)
317 return -ENXIO;
318 pp = parport_find_base(dev->base_addr);
319 if (!pp) {
320 printk(KERN_ERR "baycom_par: parport at 0x%lx unknown\n", dev->base_addr);
321 return -ENXIO;
322 }
323 if (pp->irq < 0) {
324 printk(KERN_ERR "baycom_par: parport at 0x%lx has no irq\n", pp->base);
325 parport_put_port(pp);
326 return -ENXIO;
327 }
328 if ((~pp->modes) & (PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT)) {
329 printk(KERN_ERR "baycom_par: parport at 0x%lx cannot be used\n", pp->base);
330 parport_put_port(pp);
331 return -ENXIO;
332 }
333 memset(&bc->modem, 0, sizeof(bc->modem));
334 bc->hdrv.par.bitrate = 9600;
335 bc->pdev = parport_register_device(pp, dev->name, NULL, par96_wakeup,
336 par96_interrupt, PARPORT_DEV_EXCL, dev);
337 parport_put_port(pp);
338 if (!bc->pdev) {
339 printk(KERN_ERR "baycom_par: cannot register parport at 0x%lx\n", dev->base_addr);
340 return -ENXIO;
341 }
342 if (parport_claim(bc->pdev)) {
343 printk(KERN_ERR "baycom_par: parport at 0x%lx busy\n", pp->base);
344 parport_unregister_device(bc->pdev);
345 return -EBUSY;
346 }
347 pp = bc->pdev->port;
348 dev->irq = pp->irq;
349 pp->ops->data_forward(pp);
350 bc->hdrv.par.bitrate = 9600;
351 pp->ops->write_data(pp, PAR96_PTT | PAR97_POWER); /* switch off PTT */
352 pp->ops->enable_irq(pp);
353 printk(KERN_INFO "%s: par96 at iobase 0x%lx irq %u options 0x%x\n",
354 bc_drvname, dev->base_addr, dev->irq, bc->options);
355 return 0;
356}
357
358/* --------------------------------------------------------------------- */
359
360static int par96_close(struct net_device *dev)
361{
362 struct baycom_state *bc = netdev_priv(dev);
363 struct parport *pp;
364
365 if (!dev || !bc)
366 return -EINVAL;
367 pp = bc->pdev->port;
368 /* disable interrupt */
369 pp->ops->disable_irq(pp);
370 /* switch off PTT */
371 pp->ops->write_data(pp, PAR96_PTT | PAR97_POWER);
372 parport_release(bc->pdev);
373 parport_unregister_device(bc->pdev);
374 printk(KERN_INFO "%s: close par96 at iobase 0x%lx irq %u\n",
375 bc_drvname, dev->base_addr, dev->irq);
376 return 0;
377}
378
379/* --------------------------------------------------------------------- */
380/*
381 * ===================== hdlcdrv driver interface =========================
382 */
383
384static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
385 struct hdlcdrv_ioctl *hi, int cmd);
386
387/* --------------------------------------------------------------------- */
388
389static struct hdlcdrv_ops par96_ops = {
390 .drvname = bc_drvname,
391 .drvinfo = bc_drvinfo,
392 .open = par96_open,
393 .close = par96_close,
394 .ioctl = baycom_ioctl
395};
396
397/* --------------------------------------------------------------------- */
398
399static int baycom_setmode(struct baycom_state *bc, const char *modestr)
400{
401 if (!strncmp(modestr, "picpar", 6))
402 bc->options = 0;
403 else if (!strncmp(modestr, "par96", 5))
404 bc->options = BAYCOM_OPTIONS_SOFTDCD;
405 else
406 bc->options = !!strchr(modestr, '*');
407 return 0;
408}
409
410/* --------------------------------------------------------------------- */
411
412static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
413 struct hdlcdrv_ioctl *hi, int cmd)
414{
415 struct baycom_state *bc;
416 struct baycom_ioctl bi;
417
418 if (!dev)
419 return -EINVAL;
420
421 bc = netdev_priv(dev);
422 BUG_ON(bc->hdrv.magic != HDLCDRV_MAGIC);
423
424 if (cmd != SIOCDEVPRIVATE)
425 return -ENOIOCTLCMD;
426 switch (hi->cmd) {
427 default:
428 break;
429
430 case HDLCDRVCTL_GETMODE:
431 strcpy(hi->data.modename, bc->options ? "par96" : "picpar");
432 if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
433 return -EFAULT;
434 return 0;
435
436 case HDLCDRVCTL_SETMODE:
437 if (netif_running(dev) || !capable(CAP_NET_ADMIN))
438 return -EACCES;
439 hi->data.modename[sizeof(hi->data.modename)-1] = '\0';
440 return baycom_setmode(bc, hi->data.modename);
441
442 case HDLCDRVCTL_MODELIST:
443 strcpy(hi->data.modename, "par96,picpar");
444 if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
445 return -EFAULT;
446 return 0;
447
448 case HDLCDRVCTL_MODEMPARMASK:
449 return HDLCDRV_PARMASK_IOBASE;
450
451 }
452
453 if (copy_from_user(&bi, ifr->ifr_data, sizeof(bi)))
454 return -EFAULT;
455 switch (bi.cmd) {
456 default:
457 return -ENOIOCTLCMD;
458
459#ifdef BAYCOM_DEBUG
460 case BAYCOMCTL_GETDEBUG:
461 bi.data.dbg.debug1 = bc->hdrv.ptt_keyed;
462 bi.data.dbg.debug2 = bc->debug_vals.last_intcnt;
463 bi.data.dbg.debug3 = bc->debug_vals.last_pllcorr;
464 break;
465#endif /* BAYCOM_DEBUG */
466
467 }
468 if (copy_to_user(ifr->ifr_data, &bi, sizeof(bi)))
469 return -EFAULT;
470 return 0;
471
472}
473
474/* --------------------------------------------------------------------- */
475
476/*
477 * command line settable parameters
478 */
Danny Kukawkadc7cdf62012-01-30 12:00:18 +0000479static char *mode[NR_PORTS] = { "picpar", };
Linus Torvalds1da177e2005-04-16 15:20:36 -0700480static int iobase[NR_PORTS] = { 0x378, };
481
482module_param_array(mode, charp, NULL, 0);
483MODULE_PARM_DESC(mode, "baycom operating mode; eg. par96 or picpar");
484module_param_array(iobase, int, NULL, 0);
485MODULE_PARM_DESC(iobase, "baycom io base address");
486
487MODULE_AUTHOR("Thomas M. Sailer, sailer@ife.ee.ethz.ch, hb9jnx@hb9w.che.eu");
488MODULE_DESCRIPTION("Baycom par96 and picpar amateur radio modem driver");
489MODULE_LICENSE("GPL");
490
491/* --------------------------------------------------------------------- */
492
493static int __init init_baycompar(void)
494{
495 int i, found = 0;
496 char set_hw = 1;
497
498 printk(bc_drvinfo);
499 /*
500 * register net devices
501 */
502 for (i = 0; i < NR_PORTS; i++) {
503 struct net_device *dev;
504 struct baycom_state *bc;
505 char ifname[IFNAMSIZ];
506
507 sprintf(ifname, "bcp%d", i);
508
509 if (!mode[i])
510 set_hw = 0;
511 if (!set_hw)
512 iobase[i] = 0;
513
514 dev = hdlcdrv_register(&par96_ops,
515 sizeof(struct baycom_state),
516 ifname, iobase[i], 0, 0);
517 if (IS_ERR(dev))
518 break;
519
520 bc = netdev_priv(dev);
521 if (set_hw && baycom_setmode(bc, mode[i]))
522 set_hw = 0;
523 found++;
524 baycom_device[i] = dev;
525 }
526
527 if (!found)
528 return -ENXIO;
529 return 0;
530}
531
532static void __exit cleanup_baycompar(void)
533{
534 int i;
535
536 for(i = 0; i < NR_PORTS; i++) {
537 struct net_device *dev = baycom_device[i];
538
539 if (dev)
540 hdlcdrv_unregister(dev);
541 }
542}
543
544module_init(init_baycompar);
545module_exit(cleanup_baycompar);
546
547/* --------------------------------------------------------------------- */
548
549#ifndef MODULE
550
551/*
552 * format: baycom_par=io,mode
553 * mode: par96,picpar
554 */
555
556static int __init baycom_par_setup(char *str)
557{
558 static unsigned nr_dev;
559 int ints[2];
560
561 if (nr_dev >= NR_PORTS)
562 return 0;
563 str = get_options(str, 2, ints);
564 if (ints[0] < 1)
565 return 0;
566 mode[nr_dev] = str;
567 iobase[nr_dev] = ints[1];
568 nr_dev++;
569 return 1;
570}
571
572__setup("baycom_par=", baycom_par_setup);
573
574#endif /* MODULE */
575/* --------------------------------------------------------------------- */