Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | # |
| 2 | # IDE ATA ATAPI Block device driver configuration |
| 3 | # |
| 4 | # Andre Hedrick <andre@linux-ide.org> |
| 5 | # |
| 6 | |
Jan Engelhardt | e0ff9cd | 2007-05-16 00:51:46 +0200 | [diff] [blame] | 7 | menuconfig IDE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 8 | tristate "ATA/ATAPI/MFM/RLL support" |
Jan Engelhardt | e0ff9cd | 2007-05-16 00:51:46 +0200 | [diff] [blame] | 9 | depends on BLOCK |
| 10 | depends on HAS_IOMEM |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 11 | ---help--- |
| 12 | If you say Y here, your kernel will be able to manage low cost mass |
| 13 | storage units such as ATA/(E)IDE and ATAPI units. The most common |
| 14 | cases are IDE hard drives and ATAPI CD-ROM drives. |
| 15 | |
| 16 | If your system is pure SCSI and doesn't use these interfaces, you |
| 17 | can say N here. |
| 18 | |
| 19 | Integrated Disk Electronics (IDE aka ATA-1) is a connecting standard |
| 20 | for mass storage units such as hard disks. It was designed by |
| 21 | Western Digital and Compaq Computer in 1984. It was then named |
| 22 | ST506. Quite a number of disks use the IDE interface. |
| 23 | |
| 24 | AT Attachment (ATA) is the superset of the IDE specifications. |
| 25 | ST506 was also called ATA-1. |
| 26 | |
| 27 | Fast-IDE is ATA-2 (also named Fast ATA), Enhanced IDE (EIDE) is |
| 28 | ATA-3. It provides support for larger disks (up to 8.4GB by means of |
| 29 | the LBA standard), more disks (4 instead of 2) and for other mass |
| 30 | storage units such as tapes and cdrom. UDMA/33 (aka UltraDMA/33) is |
| 31 | ATA-4 and provides faster (and more CPU friendly) transfer modes |
| 32 | than previous PIO (Programmed processor Input/Output) from previous |
| 33 | ATA/IDE standards by means of fast DMA controllers. |
| 34 | |
| 35 | ATA Packet Interface (ATAPI) is a protocol used by EIDE tape and |
| 36 | CD-ROM drives, similar in many respects to the SCSI protocol. |
| 37 | |
| 38 | SMART IDE (Self Monitoring, Analysis and Reporting Technology) was |
| 39 | designed in order to prevent data corruption and disk crash by |
| 40 | detecting pre hardware failure conditions (heat, access time, and |
| 41 | the like...). Disks built since June 1995 may follow this standard. |
| 42 | The kernel itself doesn't manage this; however there are quite a |
| 43 | number of user programs such as smart that can query the status of |
| 44 | SMART parameters from disk drives. |
| 45 | |
| 46 | To compile this driver as a module, choose M here: the |
| 47 | module will be called ide. |
| 48 | |
| 49 | For further information, please read <file:Documentation/ide.txt>. |
| 50 | |
| 51 | If unsure, say Y. |
| 52 | |
| 53 | if IDE |
| 54 | |
Bjorn Helgaas | d57d39c | 2006-02-03 03:04:53 -0800 | [diff] [blame] | 55 | config IDE_MAX_HWIFS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 56 | int "Max IDE interfaces" |
Matt Mackall | 83d7dbc | 2006-10-03 01:14:16 -0700 | [diff] [blame] | 57 | depends on ALPHA || SUPERH || IA64 || EMBEDDED |
Bartlomiej Zolnierkiewicz | 8929fea | 2007-04-20 22:16:58 +0200 | [diff] [blame] | 58 | range 1 10 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 59 | default 4 |
| 60 | help |
| 61 | This is the maximum number of IDE hardware interfaces that will |
| 62 | be supported by the driver. Make sure it is at least as high as |
| 63 | the number of IDE interfaces in your system. |
| 64 | |
| 65 | config BLK_DEV_IDE |
| 66 | tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support" |
| 67 | ---help--- |
| 68 | If you say Y here, you will use the full-featured IDE driver to |
| 69 | control up to ten ATA/IDE interfaces, each being able to serve a |
| 70 | "master" and a "slave" device, for a total of up to twenty ATA/IDE |
| 71 | disk/cdrom/tape/floppy drives. |
| 72 | |
| 73 | Useful information about large (>540 MB) IDE disks, multiple |
| 74 | interfaces, what to do if ATA/IDE devices are not automatically |
| 75 | detected, sound card ATA/IDE ports, module support, and other |
| 76 | topics, is contained in <file:Documentation/ide.txt>. For detailed |
| 77 | information about hard drives, consult the Disk-HOWTO and the |
| 78 | Multi-Disk-HOWTO, available from |
| 79 | <http://www.tldp.org/docs.html#howto>. |
| 80 | |
| 81 | To fine-tune ATA/IDE drive/interface parameters for improved |
| 82 | performance, look for the hdparm package at |
| 83 | <ftp://ibiblio.org/pub/Linux/system/hardware/>. |
| 84 | |
| 85 | To compile this driver as a module, choose M here and read |
| 86 | <file:Documentation/ide.txt>. The module will be called ide-mod. |
| 87 | Do not compile this driver as a module if your root file system (the |
| 88 | one containing the directory /) is located on an IDE device. |
| 89 | |
| 90 | If you have one or more IDE drives, say Y or M here. If your system |
| 91 | has no IDE drives, or if memory requirements are really tight, you |
| 92 | could say N here, and select the "Old hard disk driver" below |
| 93 | instead to save about 13 KB of memory in the kernel. |
| 94 | |
| 95 | if BLK_DEV_IDE |
| 96 | |
| 97 | comment "Please see Documentation/ide.txt for help/info on IDE drives" |
| 98 | |
| 99 | config BLK_DEV_IDE_SATA |
| 100 | bool "Support for SATA (deprecated; conflicts with libata SATA driver)" |
| 101 | default n |
| 102 | ---help--- |
| 103 | There are two drivers for Serial ATA controllers. |
| 104 | |
Patrick Ringl | b43c5f3 | 2007-03-26 23:03:19 +0200 | [diff] [blame] | 105 | The main driver, "libata", uses the SCSI subsystem |
| 106 | and supports most modern SATA controllers. In order to use it |
| 107 | you may take a look at "Serial ATA (prod) and Parallel ATA |
| 108 | (experimental) drivers". |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 109 | |
| 110 | The IDE driver (which you are currently configuring) supports |
| 111 | a few first-generation SATA controllers. |
| 112 | |
| 113 | In order to eliminate conflicts between the two subsystems, |
| 114 | this config option enables the IDE driver's SATA support. |
| 115 | Normally this is disabled, as it is preferred that libata |
| 116 | supports SATA controllers, and this (IDE) driver supports |
| 117 | PATA controllers. |
| 118 | |
| 119 | If unsure, say N. |
| 120 | |
| 121 | config BLK_DEV_HD_IDE |
| 122 | bool "Use old disk-only driver on primary interface" |
| 123 | depends on (X86 || SH_MPC1211) |
| 124 | ---help--- |
| 125 | There are two drivers for MFM/RLL/IDE disks. Most people use just |
| 126 | the new enhanced driver by itself. This option however installs the |
| 127 | old hard disk driver to control the primary IDE/disk interface in |
| 128 | the system, leaving the new enhanced IDE driver to take care of only |
| 129 | the 2nd/3rd/4th IDE interfaces. Doing this will prevent you from |
| 130 | having an IDE/ATAPI CD-ROM or tape drive connected to the primary |
| 131 | IDE interface. Choosing this option may be useful for older systems |
| 132 | which have MFM/RLL/ESDI controller+drives at the primary port |
| 133 | address (0x1f0), along with IDE drives at the secondary/3rd/4th port |
| 134 | addresses. |
| 135 | |
| 136 | Normally, just say N here; you will then use the new driver for all |
| 137 | 4 interfaces. |
| 138 | |
| 139 | config BLK_DEV_IDEDISK |
| 140 | tristate "Include IDE/ATA-2 DISK support" |
| 141 | ---help--- |
| 142 | This will include enhanced support for MFM/RLL/IDE hard disks. If |
| 143 | you have a MFM/RLL/IDE disk, and there is no special reason to use |
| 144 | the old hard disk driver instead, say Y. If you have an SCSI-only |
| 145 | system, you can say N here. |
| 146 | |
| 147 | To compile this driver as a module, choose M here: the |
| 148 | module will be called ide-disk. |
| 149 | Do not compile this driver as a module if your root file system |
| 150 | (the one containing the directory /) is located on the IDE disk. |
| 151 | |
| 152 | If unsure, say Y. |
| 153 | |
| 154 | config IDEDISK_MULTI_MODE |
| 155 | bool "Use multi-mode by default" |
| 156 | help |
| 157 | If you get this error, try to say Y here: |
| 158 | |
| 159 | hda: set_multmode: status=0x51 { DriveReady SeekComplete Error } |
| 160 | hda: set_multmode: error=0x04 { DriveStatusError } |
| 161 | |
| 162 | If in doubt, say N. |
| 163 | |
| 164 | config BLK_DEV_IDECS |
| 165 | tristate "PCMCIA IDE support" |
| 166 | depends on PCMCIA |
| 167 | help |
Andreas Mohr | 3b6ce24 | 2006-02-03 03:04:54 -0800 | [diff] [blame] | 168 | Support for Compact Flash cards, outboard IDE disks, tape drives, |
| 169 | and CD-ROM drives connected through a PCMCIA card. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 170 | |
Mark Lord | 78281c5 | 2007-02-07 18:19:32 +0100 | [diff] [blame] | 171 | config BLK_DEV_DELKIN |
| 172 | tristate "Cardbus IDE support (Delkin/ASKA/Workbit)" |
| 173 | depends on CARDBUS && PCI |
| 174 | help |
| 175 | Support for Delkin, ASKA, and Workbit Cardbus CompactFlash |
| 176 | Adapters. This may also work for similar SD and XD adapters. |
| 177 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 178 | config BLK_DEV_IDECD |
| 179 | tristate "Include IDE/ATAPI CDROM support" |
| 180 | ---help--- |
| 181 | If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is |
| 182 | a newer protocol used by IDE CD-ROM and TAPE drives, similar to the |
| 183 | SCSI protocol. Most new CD-ROM drives use ATAPI, including the |
| 184 | NEC-260, Mitsumi FX400, Sony 55E, and just about all non-SCSI |
| 185 | double(2X) or better speed drives. |
| 186 | |
| 187 | If you say Y here, the CD-ROM drive will be identified at boot time |
| 188 | along with other IDE devices, as "hdb" or "hdc", or something |
| 189 | similar (check the boot messages with dmesg). If this is your only |
| 190 | CD-ROM drive, you can say N to all other CD-ROM options, but be sure |
| 191 | to say Y or M to "ISO 9660 CD-ROM file system support". |
| 192 | |
| 193 | Note that older versions of LILO (LInux LOader) cannot properly deal |
| 194 | with IDE/ATAPI CD-ROMs, so install LILO 16 or higher, available from |
| 195 | <http://lilo.go.dyndns.org/>. |
| 196 | |
| 197 | To compile this driver as a module, choose M here: the |
| 198 | module will be called ide-cd. |
| 199 | |
| 200 | config BLK_DEV_IDETAPE |
| 201 | tristate "Include IDE/ATAPI TAPE support (EXPERIMENTAL)" |
| 202 | depends on EXPERIMENTAL |
| 203 | help |
| 204 | If you have an IDE tape drive using the ATAPI protocol, say Y. |
| 205 | ATAPI is a newer protocol used by IDE tape and CD-ROM drives, |
| 206 | similar to the SCSI protocol. If you have an SCSI tape drive |
| 207 | however, you can say N here. |
| 208 | |
| 209 | You should also say Y if you have an OnStream DI-30 tape drive; this |
| 210 | will not work with the SCSI protocol, until there is support for the |
| 211 | SC-30 and SC-50 versions. |
| 212 | |
| 213 | If you say Y here, the tape drive will be identified at boot time |
| 214 | along with other IDE devices, as "hdb" or "hdc", or something |
| 215 | similar, and will be mapped to a character device such as "ht0" |
| 216 | (check the boot messages with dmesg). Be sure to consult the |
| 217 | <file:drivers/ide/ide-tape.c> and <file:Documentation/ide.txt> files |
| 218 | for usage information. |
| 219 | |
| 220 | To compile this driver as a module, choose M here: the |
| 221 | module will be called ide-tape. |
| 222 | |
| 223 | config BLK_DEV_IDEFLOPPY |
| 224 | tristate "Include IDE/ATAPI FLOPPY support" |
| 225 | ---help--- |
| 226 | If you have an IDE floppy drive which uses the ATAPI protocol, |
| 227 | answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy |
| 228 | drives, similar to the SCSI protocol. |
| 229 | |
| 230 | The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by |
| 231 | this driver. For information about jumper settings and the question |
| 232 | of when a ZIP drive uses a partition table, see |
| 233 | <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>. |
| 234 | (ATAPI PD-CD/CDR drives are not supported by this driver; support |
| 235 | for PD-CD/CDR drives is available if you answer Y to |
| 236 | "SCSI emulation support", below). |
| 237 | |
| 238 | If you say Y here, the FLOPPY drive will be identified along with |
| 239 | other IDE devices, as "hdb" or "hdc", or something similar (check |
| 240 | the boot messages with dmesg). |
| 241 | |
| 242 | To compile this driver as a module, choose M here: the |
| 243 | module will be called ide-floppy. |
| 244 | |
| 245 | config BLK_DEV_IDESCSI |
| 246 | tristate "SCSI emulation support" |
| 247 | depends on SCSI |
| 248 | ---help--- |
| 249 | WARNING: ide-scsi is no longer needed for cd writing applications! |
| 250 | The 2.6 kernel supports direct writing to ide-cd, which eliminates |
| 251 | the need for ide-scsi + the entire scsi stack just for writing a |
| 252 | cd. The new method is more efficient in every way. |
| 253 | |
| 254 | This will provide SCSI host adapter emulation for IDE ATAPI devices, |
| 255 | and will allow you to use a SCSI device driver instead of a native |
| 256 | ATAPI driver. |
| 257 | |
| 258 | This is useful if you have an ATAPI device for which no native |
| 259 | driver has been written (for example, an ATAPI PD-CD drive); |
| 260 | you can then use this emulation together with an appropriate SCSI |
| 261 | device driver. In order to do this, say Y here and to "SCSI support" |
| 262 | and "SCSI generic support", below. You must then provide the kernel |
| 263 | command line "hdx=ide-scsi" (try "man bootparam" or see the |
| 264 | documentation of your boot loader (lilo or loadlin) about how to |
| 265 | pass options to the kernel at boot time) for devices if you want the |
| 266 | native EIDE sub-drivers to skip over the native support, so that |
| 267 | this SCSI emulation can be used instead. |
| 268 | |
| 269 | Note that this option does NOT allow you to attach SCSI devices to a |
| 270 | box that doesn't have a SCSI host adapter installed. |
| 271 | |
| 272 | If both this SCSI emulation and native ATAPI support are compiled |
| 273 | into the kernel, the native support will be used. |
| 274 | |
Hannes Reinecke | e3a59b4 | 2007-02-07 18:19:37 +0100 | [diff] [blame] | 275 | config BLK_DEV_IDEACPI |
| 276 | bool "IDE ACPI support" |
| 277 | depends on ACPI |
| 278 | ---help--- |
| 279 | Implement ACPI support for generic IDE devices. On modern |
| 280 | machines ACPI support is required to properly handle ACPI S3 states. |
| 281 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 282 | config IDE_TASK_IOCTL |
| 283 | bool "IDE Taskfile Access" |
| 284 | help |
| 285 | This is a direct raw access to the media. It is a complex but |
| 286 | elegant solution to test and validate the domain of the hardware and |
Andreas Mohr | 3b6ce24 | 2006-02-03 03:04:54 -0800 | [diff] [blame] | 287 | perform below the driver data recovery if needed. This is the most |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 288 | basic form of media-forensics. |
| 289 | |
| 290 | If you are unsure, say N here. |
| 291 | |
Bartlomiej Zolnierkiewicz | ecfd80e | 2007-05-10 00:01:09 +0200 | [diff] [blame] | 292 | config IDE_PROC_FS |
| 293 | bool "legacy /proc/ide/ support" |
| 294 | depends on IDE && PROC_FS |
| 295 | default y |
| 296 | help |
| 297 | This option enables support for the various files in |
| 298 | /proc/ide. In Linux 2.6 this has been superseded by |
| 299 | files in sysfs but many legacy applications rely on this. |
| 300 | |
| 301 | If unsure say Y. |
| 302 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 303 | comment "IDE chipset support/bugfixes" |
| 304 | |
| 305 | config IDE_GENERIC |
| 306 | tristate "generic/default IDE chipset support" |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 307 | default H8300 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 308 | help |
Tejun Heo | 82a0e70 | 2007-08-20 22:42:53 +0200 | [diff] [blame] | 309 | If unsure, say N. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 310 | |
| 311 | config BLK_DEV_CMD640 |
| 312 | bool "CMD640 chipset bugfix/support" |
| 313 | depends on X86 |
| 314 | ---help--- |
| 315 | The CMD-Technologies CMD640 IDE chip is used on many common 486 and |
| 316 | Pentium motherboards, usually in combination with a "Neptune" or |
| 317 | "SiS" chipset. Unfortunately, it has a number of rather nasty |
| 318 | design flaws that can cause severe data corruption under many common |
| 319 | conditions. Say Y here to include code which tries to automatically |
| 320 | detect and correct the problems under Linux. This option also |
| 321 | enables access to the secondary IDE ports in some CMD640 based |
| 322 | systems. |
| 323 | |
| 324 | This driver will work automatically in PCI based systems (most new |
| 325 | systems have PCI slots). But if your system uses VESA local bus |
| 326 | (VLB) instead of PCI, you must also supply a kernel boot parameter |
| 327 | to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man |
| 328 | bootparam" or see the documentation of your boot loader about how to |
| 329 | pass options to the kernel.) |
| 330 | |
| 331 | The CMD640 chip is also used on add-in cards by Acculogic, and on |
| 332 | the "CSA-6400E PCI to IDE controller" that some people have. For |
| 333 | details, read <file:Documentation/ide.txt>. |
| 334 | |
| 335 | config BLK_DEV_CMD640_ENHANCED |
| 336 | bool "CMD640 enhanced support" |
| 337 | depends on BLK_DEV_CMD640 |
| 338 | help |
| 339 | This option includes support for setting/autotuning PIO modes and |
| 340 | prefetch on CMD640 IDE interfaces. For details, read |
| 341 | <file:Documentation/ide.txt>. If you have a CMD640 IDE interface |
| 342 | and your BIOS does not already do this for you, then say Y here. |
| 343 | Otherwise say N. |
| 344 | |
| 345 | config BLK_DEV_IDEPNP |
| 346 | bool "PNP EIDE support" |
| 347 | depends on PNP |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 348 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 349 | help |
| 350 | If you have a PnP (Plug and Play) compatible EIDE card and |
| 351 | would like the kernel to automatically detect and activate |
| 352 | it, say Y here. |
| 353 | |
| 354 | config BLK_DEV_IDEPCI |
| 355 | bool "PCI IDE chipset support" if PCI |
| 356 | default BLK_DEV_IDEDMA_PMAC if PPC_PMAC && BLK_DEV_IDEDMA_PMAC |
| 357 | help |
| 358 | Say Y here for PCI systems which use IDE drive(s). |
| 359 | This option helps the IDE driver to automatically detect and |
| 360 | configure all PCI-based IDE interfaces in your system. |
| 361 | |
| 362 | config IDEPCI_SHARE_IRQ |
| 363 | bool "Sharing PCI IDE interrupts support" |
| 364 | depends on PCI && BLK_DEV_IDEPCI |
| 365 | help |
| 366 | Some ATA/IDE chipsets have hardware support which allows for |
| 367 | sharing a single IRQ with other cards. To enable support for |
| 368 | this in the ATA/IDE driver, say Y here. |
| 369 | |
| 370 | It is safe to say Y to this question, in most cases. |
| 371 | If unsure, say N. |
| 372 | |
Bartlomiej Zolnierkiewicz | 6d208b3 | 2007-05-10 00:01:11 +0200 | [diff] [blame] | 373 | config IDEPCI_PCIBUS_ORDER |
| 374 | def_bool PCI && BLK_DEV_IDE=y && BLK_DEV_IDEPCI |
| 375 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 376 | config BLK_DEV_OFFBOARD |
| 377 | bool "Boot off-board chipsets first support" |
| 378 | depends on PCI && BLK_DEV_IDEPCI |
| 379 | help |
| 380 | Normally, IDE controllers built into the motherboard (on-board |
| 381 | controllers) are assigned to ide0 and ide1 while those on add-in PCI |
| 382 | cards (off-board controllers) are relegated to ide2 and ide3. |
| 383 | Answering Y here will allow you to reverse the situation, with |
| 384 | off-board controllers on ide0/1 and on-board controllers on ide2/3. |
| 385 | This can improve the usability of some boot managers such as lilo |
| 386 | when booting from a drive on an off-board controller. |
| 387 | |
| 388 | If you say Y here, and you actually want to reverse the device scan |
| 389 | order as explained above, you also need to issue the kernel command |
| 390 | line option "ide=reverse". (Try "man bootparam" or see the |
| 391 | documentation of your boot loader (lilo or loadlin) about how to |
| 392 | pass options to the kernel at boot time.) |
| 393 | |
| 394 | Note that, if you do this, the order of the hd* devices will be |
| 395 | rearranged which may require modification of fstab and other files. |
| 396 | |
| 397 | If in doubt, say N. |
| 398 | |
| 399 | config BLK_DEV_GENERIC |
| 400 | tristate "Generic PCI IDE Chipset Support" |
| 401 | depends on BLK_DEV_IDEPCI |
John Daiker | edd023d | 2007-02-17 19:52:10 +0100 | [diff] [blame] | 402 | help |
| 403 | This option provides generic support for various PCI IDE Chipsets |
| 404 | which otherwise might not be supported. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 405 | |
| 406 | config BLK_DEV_OPTI621 |
| 407 | tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)" |
| 408 | depends on PCI && BLK_DEV_IDEPCI && EXPERIMENTAL |
| 409 | help |
| 410 | This is a driver for the OPTi 82C621 EIDE controller. |
| 411 | Please read the comments at the top of <file:drivers/ide/pci/opti621.c>. |
| 412 | |
| 413 | config BLK_DEV_RZ1000 |
| 414 | tristate "RZ1000 chipset bugfix/support" |
| 415 | depends on PCI && BLK_DEV_IDEPCI && X86 |
| 416 | help |
| 417 | The PC-Technologies RZ1000 IDE chip is used on many common 486 and |
| 418 | Pentium motherboards, usually along with the "Neptune" chipset. |
| 419 | Unfortunately, it has a rather nasty design flaw that can cause |
| 420 | severe data corruption under many conditions. Say Y here to include |
| 421 | code which automatically detects and corrects the problem under |
| 422 | Linux. This may slow disk throughput by a few percent, but at least |
| 423 | things will operate 100% reliably. |
| 424 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 425 | config BLK_DEV_IDEDMA_PCI |
| 426 | bool "Generic PCI bus-master DMA support" |
| 427 | depends on PCI && BLK_DEV_IDEPCI |
| 428 | ---help--- |
| 429 | If your PCI system uses IDE drive(s) (as opposed to SCSI, say) and |
| 430 | is capable of bus-master DMA operation (most Pentium PCI systems), |
| 431 | you will want to say Y here to reduce CPU overhead. You can then use |
| 432 | the "hdparm" utility to enable DMA for drives for which it was not |
| 433 | enabled automatically. By default, DMA is not enabled automatically |
| 434 | for these drives, but you can change that by saying Y to the |
| 435 | following question "Use DMA by default when available". You can get |
| 436 | the latest version of the hdparm utility from |
| 437 | <ftp://ibiblio.org/pub/Linux/system/hardware/>. |
| 438 | |
| 439 | Read the comments at the beginning of <file:drivers/ide/ide-dma.c> |
| 440 | and the file <file:Documentation/ide.txt> for more information. |
| 441 | |
| 442 | It is safe to say Y to this question. |
| 443 | |
| 444 | if BLK_DEV_IDEDMA_PCI |
| 445 | |
| 446 | config BLK_DEV_IDEDMA_FORCED |
| 447 | bool "Force enable legacy 2.0.X HOSTS to use DMA" |
| 448 | help |
| 449 | This is an old piece of lost code from Linux 2.0 Kernels. |
| 450 | |
| 451 | Generally say N here. |
| 452 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 453 | config IDEDMA_ONLYDISK |
| 454 | bool "Enable DMA only for disks " |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 455 | help |
| 456 | This is used if you know your ATAPI Devices are going to fail DMA |
| 457 | Transfers. |
| 458 | |
| 459 | Generally say N here. |
| 460 | |
| 461 | config BLK_DEV_AEC62XX |
| 462 | tristate "AEC62XX chipset support" |
| 463 | help |
| 464 | This driver adds explicit support for Acard AEC62xx (Artop ATP8xx) |
| 465 | IDE controllers. This allows the kernel to change PIO, DMA and UDMA |
| 466 | speeds and to configure the chip to optimum performance. |
| 467 | |
| 468 | config BLK_DEV_ALI15X3 |
| 469 | tristate "ALI M15x3 chipset support" |
| 470 | help |
| 471 | This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C |
| 472 | onboard chipsets. It also tests for Simplex mode and enables |
| 473 | normal dual channel support. |
| 474 | |
| 475 | If you say Y here, you also need to say Y to "Use DMA by default |
| 476 | when available", above. Please read the comments at the top of |
| 477 | <file:drivers/ide/pci/alim15x3.c>. |
| 478 | |
| 479 | If unsure, say N. |
| 480 | |
| 481 | config WDC_ALI15X3 |
| 482 | bool "ALI M15x3 WDC support (DANGEROUS)" |
| 483 | depends on BLK_DEV_ALI15X3 |
| 484 | ---help--- |
| 485 | This allows for UltraDMA support for WDC drives that ignore CRC |
| 486 | checking. You are a fool for enabling this option, but there have |
| 487 | been requests. DO NOT COMPLAIN IF YOUR DRIVE HAS FS CORRUPTION, IF |
| 488 | YOU ENABLE THIS! No one will listen, just laugh for ignoring this |
| 489 | SERIOUS WARNING. |
| 490 | |
| 491 | Using this option can allow WDC drives to run at ATA-4/5 transfer |
| 492 | rates with only an ATA-2 support structure. |
| 493 | |
| 494 | SAY N! |
| 495 | |
| 496 | config BLK_DEV_AMD74XX |
| 497 | tristate "AMD and nVidia IDE support" |
| 498 | help |
| 499 | This driver adds explicit support for AMD-7xx and AMD-8111 chips |
| 500 | and also for the nVidia nForce chip. This allows the kernel to |
| 501 | change PIO, DMA and UDMA speeds and to configure the chip to |
| 502 | optimum performance. |
| 503 | |
| 504 | config BLK_DEV_ATIIXP |
| 505 | tristate "ATI IXP chipset IDE support" |
| 506 | depends on X86 |
| 507 | help |
| 508 | This driver adds explicit support for ATI IXP chipset. |
| 509 | This allows the kernel to change PIO, DMA and UDMA speeds |
| 510 | and to configure the chip to optimum performance. |
| 511 | |
| 512 | Say Y here if you have an ATI IXP chipset IDE controller. |
| 513 | |
| 514 | config BLK_DEV_CMD64X |
| 515 | tristate "CMD64{3|6|8|9} chipset support" |
| 516 | help |
| 517 | Say Y here if you have an IDE controller which uses any of these |
| 518 | chipsets: CMD643, CMD646, or CMD648. |
| 519 | |
| 520 | config BLK_DEV_TRIFLEX |
| 521 | tristate "Compaq Triflex IDE support" |
| 522 | help |
| 523 | Say Y here if you have a Compaq Triflex IDE controller, such |
| 524 | as those commonly found on Compaq Pentium-Pro systems |
| 525 | |
| 526 | config BLK_DEV_CY82C693 |
| 527 | tristate "CY82C693 chipset support" |
| 528 | help |
| 529 | This driver adds detection and support for the CY82C693 chipset |
| 530 | used on Digital's PC-Alpha 164SX boards. |
| 531 | |
| 532 | If you say Y here, you need to say Y to "Use DMA by default |
| 533 | when available" as well. |
| 534 | |
| 535 | config BLK_DEV_CS5520 |
| 536 | tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)" |
| 537 | depends on EXPERIMENTAL |
| 538 | help |
Andreas Mohr | 3b6ce24 | 2006-02-03 03:04:54 -0800 | [diff] [blame] | 539 | Include support for PIO tuning and virtual DMA on the Cyrix MediaGX |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 540 | 5510/5520 chipset. This will automatically be detected and |
| 541 | configured if found. |
| 542 | |
| 543 | It is safe to say Y to this question. |
| 544 | |
| 545 | config BLK_DEV_CS5530 |
| 546 | tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support" |
| 547 | help |
| 548 | Include support for UDMA on the Cyrix MediaGX 5530 chipset. This |
| 549 | will automatically be detected and configured if found. |
| 550 | |
| 551 | It is safe to say Y to this question. |
| 552 | |
Jaya Kumar | f5b2d8b | 2005-11-09 23:58:16 +0100 | [diff] [blame] | 553 | config BLK_DEV_CS5535 |
| 554 | tristate "AMD CS5535 chipset support" |
| 555 | depends on X86 && !X86_64 |
| 556 | help |
| 557 | Include support for UDMA on the NSC/AMD CS5535 companion chipset. |
| 558 | This will automatically be detected and configured if found. |
| 559 | |
| 560 | It is safe to say Y to this question. |
| 561 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 562 | config BLK_DEV_HPT34X |
| 563 | tristate "HPT34X chipset support" |
| 564 | help |
| 565 | This driver adds up to 4 more EIDE devices sharing a single |
| 566 | interrupt. The HPT343 chipset in its current form is a non-bootable |
| 567 | controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX) |
| 568 | PCI UDMA controllers. This driver requires dynamic tuning of the |
| 569 | chipset during the ide-probe at boot time. It is reported to support |
| 570 | DVD II drives, by the manufacturer. |
| 571 | |
| 572 | config HPT34X_AUTODMA |
| 573 | bool "HPT34X AUTODMA support (EXPERIMENTAL)" |
| 574 | depends on BLK_DEV_HPT34X && EXPERIMENTAL |
| 575 | help |
| 576 | This is a dangerous thing to attempt currently! Please read the |
| 577 | comments at the top of <file:drivers/ide/pci/hpt34x.c>. If you say Y |
| 578 | here, then say Y to "Use DMA by default when available" as well. |
| 579 | |
| 580 | If unsure, say N. |
| 581 | |
| 582 | config BLK_DEV_HPT366 |
| 583 | tristate "HPT36X/37X chipset support" |
| 584 | ---help--- |
| 585 | HPT366 is an Ultra DMA chipset for ATA-66. |
| 586 | HPT368 is an Ultra DMA chipset for ATA-66 RAID Based. |
| 587 | HPT370 is an Ultra DMA chipset for ATA-100. |
| 588 | HPT372 is an Ultra DMA chipset for ATA-100. |
| 589 | HPT374 is an Ultra DMA chipset for ATA-100. |
| 590 | |
| 591 | This driver adds up to 4 more EIDE devices sharing a single |
| 592 | interrupt. |
| 593 | |
| 594 | The HPT366 chipset in its current form is bootable. One solution |
| 595 | for this problem are special LILO commands for redirecting the |
| 596 | reference to device 0x80. The other solution is to say Y to "Boot |
| 597 | off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless |
| 598 | your mother board has the chipset natively mounted. Regardless one |
| 599 | should use the fore mentioned option and call at LILO or include |
| 600 | "ide=reverse" in LILO's append-line. |
| 601 | |
| 602 | This driver requires dynamic tuning of the chipset during the |
| 603 | ide-probe at boot. It is reported to support DVD II drives, by the |
| 604 | manufacturer. |
| 605 | |
Alan Cox | bbb3bbd | 2006-10-03 01:14:12 -0700 | [diff] [blame] | 606 | config BLK_DEV_JMICRON |
| 607 | tristate "JMicron JMB36x support" |
| 608 | help |
| 609 | Basic support for the JMicron ATA controllers. For full support |
| 610 | use the libata drivers. |
| 611 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 612 | config BLK_DEV_SC1200 |
| 613 | tristate "National SCx200 chipset support" |
| 614 | help |
| 615 | This driver adds support for the built in IDE on the National |
| 616 | SCx200 series of embedded x86 "Geode" systems |
| 617 | |
| 618 | config BLK_DEV_PIIX |
| 619 | tristate "Intel PIIXn chipsets support" |
| 620 | help |
| 621 | This driver adds explicit support for Intel PIIX and ICH chips |
| 622 | and also for the Efar Victory66 (slc90e66) chip. This allows |
| 623 | the kernel to change PIO, DMA and UDMA speeds and to configure |
| 624 | the chip to optimum performance. |
| 625 | |
Jack Lee | 9c6712c | 2007-02-07 18:19:09 +0100 | [diff] [blame] | 626 | config BLK_DEV_IT8213 |
| 627 | tristate "IT8213 IDE support" |
| 628 | help |
| 629 | This driver adds support for the ITE 8213 IDE controller. |
| 630 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 631 | config BLK_DEV_IT821X |
| 632 | tristate "IT821X IDE support" |
| 633 | help |
| 634 | This driver adds support for the ITE 8211 IDE controller and the |
| 635 | IT 8212 IDE RAID controller in both RAID and pass-through mode. |
| 636 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 637 | config BLK_DEV_NS87415 |
| 638 | tristate "NS87415 chipset support" |
| 639 | help |
| 640 | This driver adds detection and support for the NS87415 chip |
Matthew Wilcox | 41df894 | 2005-11-18 16:18:40 -0500 | [diff] [blame] | 641 | (used mainly on SPARC64 and PA-RISC machines). |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 642 | |
| 643 | Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>. |
| 644 | |
| 645 | config BLK_DEV_PDC202XX_OLD |
| 646 | tristate "PROMISE PDC202{46|62|65|67} support" |
| 647 | help |
| 648 | Promise Ultra33 or PDC20246 |
| 649 | Promise Ultra66 or PDC20262 |
| 650 | Promise Ultra100 or PDC20265/PDC20267/PDC20268 |
| 651 | |
| 652 | This driver adds up to 4 more EIDE devices sharing a single |
| 653 | interrupt. This add-on card is a bootable PCI UDMA controller. Since |
| 654 | multiple cards can be installed and there are BIOS ROM problems that |
| 655 | happen if the BIOS revisions of all installed cards (three-max) do |
| 656 | not match, the driver attempts to do dynamic tuning of the chipset |
| 657 | at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required |
| 658 | for more than one card. This card may require that you say Y to |
| 659 | "Special UDMA Feature". |
| 660 | |
| 661 | If you say Y here, you need to say Y to "Use DMA by default when |
| 662 | available" as well. |
| 663 | |
| 664 | Please read the comments at the top of |
| 665 | <file:drivers/ide/pci/pdc202xx_old.c>. |
| 666 | |
| 667 | If unsure, say N. |
| 668 | |
| 669 | config PDC202XX_BURST |
| 670 | bool "Special UDMA Feature" |
| 671 | depends on BLK_DEV_PDC202XX_OLD |
| 672 | help |
| 673 | This option causes the pdc202xx driver to enable UDMA modes on the |
| 674 | PDC202xx even when the PDC202xx BIOS has not done so. |
| 675 | |
| 676 | It was originally designed for the PDC20246/Ultra33, whose BIOS will |
| 677 | only setup UDMA on the first two PDC20246 cards. It has also been |
Andreas Mohr | 3b6ce24 | 2006-02-03 03:04:54 -0800 | [diff] [blame] | 678 | used successfully on a PDC20265/Ultra100, allowing use of UDMA modes |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 679 | when the PDC20265 BIOS has been disabled (for faster boot up). |
| 680 | |
| 681 | Please read the comments at the top of |
| 682 | <file:drivers/ide/pci/pdc202xx_old.c>. |
| 683 | |
| 684 | If unsure, say N. |
| 685 | |
| 686 | config BLK_DEV_PDC202XX_NEW |
| 687 | tristate "PROMISE PDC202{68|69|70|71|75|76|77} support" |
| 688 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 689 | config BLK_DEV_SVWKS |
| 690 | tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support" |
| 691 | help |
| 692 | This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5 |
| 693 | chipsets. |
| 694 | |
| 695 | config BLK_DEV_SGIIOC4 |
Brent Casavant | e5d310b | 2005-06-21 17:16:01 -0700 | [diff] [blame] | 696 | tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support" |
| 697 | depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4 |
Brent Casavant | 9578bcf | 2006-07-30 03:03:46 -0700 | [diff] [blame] | 698 | select IDEPCI_SHARE_IRQ |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 699 | help |
| 700 | This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4 |
| 701 | chipset, which has one channel and can support two devices. |
| 702 | Please say Y here if you have an Altix System from SGI. |
| 703 | |
| 704 | config BLK_DEV_SIIMAGE |
| 705 | tristate "Silicon Image chipset support" |
| 706 | help |
| 707 | This driver adds PIO/(U)DMA support for the SI CMD680 and SII |
| 708 | 3112 (Serial ATA) chips. |
| 709 | |
| 710 | config BLK_DEV_SIS5513 |
| 711 | tristate "SiS5513 chipset support" |
| 712 | depends on X86 |
| 713 | ---help--- |
| 714 | This driver ensures (U)DMA support for SIS5513 chipset family based |
| 715 | mainboards. |
| 716 | |
| 717 | The following chipsets are supported: |
| 718 | ATA16: SiS5511, SiS5513 |
| 719 | ATA33: SiS5591, SiS5597, SiS5598, SiS5600 |
| 720 | ATA66: SiS530, SiS540, SiS620, SiS630, SiS640 |
| 721 | ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740, |
| 722 | SiS745, SiS750 |
| 723 | |
| 724 | If you say Y here, you need to say Y to "Use DMA by default when |
| 725 | available" as well. |
| 726 | |
| 727 | Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>. |
| 728 | |
Olaf Hering | 9468f68 | 2006-12-06 20:39:55 -0800 | [diff] [blame] | 729 | config BLK_DEV_SL82C105 |
| 730 | tristate "Winbond SL82c105 support" |
| 731 | depends on (PPC || ARM) |
| 732 | help |
| 733 | If you have a Winbond SL82c105 IDE controller, say Y here to enable |
| 734 | special configuration for this chip. This is common on various CHRP |
| 735 | motherboards, but could be used elsewhere. If in doubt, say Y. |
| 736 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 737 | config BLK_DEV_SLC90E66 |
| 738 | tristate "SLC90E66 chipset support" |
| 739 | help |
Andreas Mohr | 3b6ce24 | 2006-02-03 03:04:54 -0800 | [diff] [blame] | 740 | This driver ensures (U)DMA support for Victory66 SouthBridges for |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 741 | SMsC with Intel NorthBridges. This is an Ultra66 based chipset. |
| 742 | The nice thing about it is that you can mix Ultra/DMA/PIO devices |
| 743 | and it will handle timing cycles. Since this is an improved |
| 744 | look-a-like to the PIIX4 it should be a nice addition. |
| 745 | |
| 746 | If you say Y here, you need to say Y to "Use DMA by default when |
| 747 | available" as well. |
| 748 | |
| 749 | Please read the comments at the top of |
| 750 | <file:drivers/ide/pci/slc90e66.c>. |
| 751 | |
| 752 | config BLK_DEV_TRM290 |
| 753 | tristate "Tekram TRM290 chipset support" |
| 754 | help |
| 755 | This driver adds support for bus master DMA transfers |
| 756 | using the Tekram TRM290 PCI IDE chip. Volunteers are |
| 757 | needed for further tweaking and development. |
| 758 | Please read the comments at the top of <file:drivers/ide/pci/trm290.c>. |
| 759 | |
| 760 | config BLK_DEV_VIA82CXXX |
| 761 | tristate "VIA82CXXX chipset support" |
| 762 | help |
| 763 | This driver adds explicit support for VIA BusMastering IDE chips. |
| 764 | This allows the kernel to change PIO, DMA and UDMA speeds and to |
| 765 | configure the chip to optimum performance. |
| 766 | |
Sergei Shtylyov | 33dced2 | 2007-02-07 18:18:45 +0100 | [diff] [blame] | 767 | config BLK_DEV_TC86C001 |
| 768 | tristate "Toshiba TC86C001 support" |
| 769 | help |
| 770 | This driver adds support for Toshiba TC86C001 GOKU-S chip. |
| 771 | |
Kou Ishizaki | a1067db | 2007-03-17 21:57:25 +0100 | [diff] [blame] | 772 | config BLK_DEV_CELLEB |
| 773 | tristate "Toshiba's Cell Reference Set IDE support" |
| 774 | depends on PPC_CELLEB |
| 775 | help |
| 776 | This driver provides support for the built-in IDE controller on |
| 777 | Toshiba Cell Reference Board. |
| 778 | If unsure, say Y. |
| 779 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 780 | endif |
| 781 | |
| 782 | config BLK_DEV_IDE_PMAC |
| 783 | bool "Builtin PowerMac IDE support" |
| 784 | depends on PPC_PMAC && IDE=y |
| 785 | help |
| 786 | This driver provides support for the built-in IDE controller on |
| 787 | most of the recent Apple Power Macintoshes and PowerBooks. |
| 788 | If unsure, say Y. |
| 789 | |
| 790 | config BLK_DEV_IDE_PMAC_ATA100FIRST |
| 791 | bool "Probe internal ATA/100 (Kauai) first" |
| 792 | depends on BLK_DEV_IDE_PMAC |
| 793 | help |
| 794 | This option will cause the ATA/100 controller found in UniNorth2 |
| 795 | based machines (Windtunnel PowerMac, Aluminium PowerBooks, ...) |
| 796 | to be probed before the ATA/66 and ATA/33 controllers. Without |
| 797 | these, those machine used to have the hard disk on hdc and the |
| 798 | CD-ROM on hda. This option changes this to more natural hda for |
| 799 | hard disk and hdc for CD-ROM. |
| 800 | |
| 801 | config BLK_DEV_IDEDMA_PMAC |
| 802 | bool "PowerMac IDE DMA support" |
| 803 | depends on BLK_DEV_IDE_PMAC |
Juha-Matti Tapio | 0ac72b3 | 2005-08-18 22:13:44 +0200 | [diff] [blame] | 804 | select BLK_DEV_IDEDMA_PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 805 | help |
| 806 | This option allows the driver for the built-in IDE controller on |
| 807 | Power Macintoshes and PowerBooks to use DMA (direct memory access) |
| 808 | to transfer data to and from memory. Saying Y is safe and improves |
| 809 | performance. |
| 810 | |
Ralf Baechle | 4237f22 | 2005-11-17 16:23:50 +0000 | [diff] [blame] | 811 | config BLK_DEV_IDE_SWARM |
| 812 | tristate "IDE for Sibyte evaluation boards" |
| 813 | depends on SIBYTE_SB1xxx_SOC |
| 814 | |
Pete Popov | 26a940e | 2005-09-15 08:03:12 +0000 | [diff] [blame] | 815 | config BLK_DEV_IDE_AU1XXX |
| 816 | bool "IDE for AMD Alchemy Au1200" |
| 817 | depends on SOC_AU1200 |
| 818 | choice |
| 819 | prompt "IDE Mode for AMD Alchemy Au1200" |
| 820 | default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA |
| 821 | depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX |
| 822 | |
| 823 | config BLK_DEV_IDE_AU1XXX_PIO_DBDMA |
| 824 | bool "PIO+DbDMA IDE for AMD Alchemy Au1200" |
| 825 | |
| 826 | config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA |
| 827 | bool "MDMA2+DbDMA IDE for AMD Alchemy Au1200" |
| 828 | depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX |
| 829 | endchoice |
| 830 | |
Pete Popov | 26a940e | 2005-09-15 08:03:12 +0000 | [diff] [blame] | 831 | config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ |
| 832 | int "Maximum transfer size (KB) per request (up to 128)" |
| 833 | default "128" |
Robert P. J. Day | bef1f40 | 2006-12-12 20:04:19 +0100 | [diff] [blame] | 834 | depends on BLK_DEV_IDE_AU1XXX |
Pete Popov | 26a940e | 2005-09-15 08:03:12 +0000 | [diff] [blame] | 835 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 836 | config IDE_ARM |
Adrian Bunk | 99eb8a5 | 2007-07-31 00:38:19 -0700 | [diff] [blame] | 837 | def_bool ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK) |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 838 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 839 | |
| 840 | config BLK_DEV_IDE_ICSIDE |
| 841 | tristate "ICS IDE interface support" |
| 842 | depends on ARM && ARCH_ACORN |
| 843 | help |
| 844 | On Acorn systems, say Y here if you wish to use the ICS IDE |
| 845 | interface card. This is not required for ICS partition support. |
| 846 | If you are unsure, say N to this. |
| 847 | |
| 848 | config BLK_DEV_IDEDMA_ICS |
| 849 | bool "ICS DMA support" |
| 850 | depends on BLK_DEV_IDE_ICSIDE |
| 851 | help |
| 852 | Say Y here if you want to add DMA (Direct Memory Access) support to |
| 853 | the ICS IDE driver. |
| 854 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 855 | config BLK_DEV_IDE_RAPIDE |
| 856 | tristate "RapIDE interface support" |
| 857 | depends on ARM && ARCH_ACORN |
| 858 | help |
| 859 | Say Y here if you want to support the Yellowstone RapIDE controller |
| 860 | manufactured for use with Acorn computers. |
| 861 | |
| 862 | config BLK_DEV_IDE_BAST |
| 863 | tristate "Simtec BAST / Thorcom VR1000 IDE support" |
| 864 | depends on ARM && (ARCH_BAST || MACH_VR1000) |
| 865 | help |
| 866 | Say Y here if you want to support the onboard IDE channels on the |
| 867 | Simtec BAST or the Thorcom VR1000 |
| 868 | |
| 869 | config BLK_DEV_GAYLE |
| 870 | bool "Amiga Gayle IDE interface support" |
| 871 | depends on AMIGA |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 872 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 873 | help |
| 874 | This is the IDE driver for the Amiga Gayle IDE interface. It supports |
| 875 | both the `A1200 style' and `A4000 style' of the Gayle IDE interface, |
| 876 | This includes builtin IDE interfaces on some Amiga models (A600, |
| 877 | A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion |
| 878 | bus (M-Tech E-Matrix 530 expansion card). |
| 879 | Say Y if you have an Amiga with a Gayle IDE interface and want to use |
| 880 | IDE devices (hard disks, CD-ROM drives, etc.) that are connected to |
| 881 | it. |
| 882 | Note that you also have to enable Zorro bus support if you want to |
| 883 | use Gayle IDE interfaces on the Zorro expansion bus. |
| 884 | |
| 885 | config BLK_DEV_IDEDOUBLER |
| 886 | bool "Amiga IDE Doubler support (EXPERIMENTAL)" |
| 887 | depends on BLK_DEV_GAYLE && EXPERIMENTAL |
| 888 | ---help--- |
| 889 | This driver provides support for the so-called `IDE doublers' (made |
| 890 | by various manufacturers, e.g. Eyetech) that can be connected to the |
| 891 | builtin IDE interface of some Amiga models. Using such an IDE |
| 892 | doubler, you can connect up to four instead of two IDE devices on |
| 893 | the Amiga's builtin IDE interface. |
| 894 | |
| 895 | Note that the normal Amiga Gayle IDE driver may not work correctly |
| 896 | if you have an IDE doubler and don't enable this driver! |
| 897 | |
| 898 | Say Y if you have an IDE doubler. The driver is enabled at kernel |
| 899 | runtime using the "ide=doubler" kernel boot parameter. |
| 900 | |
| 901 | config BLK_DEV_BUDDHA |
| 902 | bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)" |
| 903 | depends on ZORRO && EXPERIMENTAL |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 904 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 905 | help |
| 906 | This is the IDE driver for the IDE interfaces on the Buddha, |
| 907 | Catweasel and X-Surf expansion boards. It supports up to two interfaces |
| 908 | on the Buddha, three on the Catweasel and two on the X-Surf. |
| 909 | |
| 910 | Say Y if you have a Buddha or Catweasel expansion board and want to |
| 911 | use IDE devices (hard disks, CD-ROM drives, etc.) that are connected |
| 912 | to one of its IDE interfaces. |
| 913 | |
| 914 | config BLK_DEV_FALCON_IDE |
| 915 | bool "Falcon IDE interface support" |
| 916 | depends on ATARI |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 917 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 918 | help |
| 919 | This is the IDE driver for the builtin IDE interface on the Atari |
| 920 | Falcon. Say Y if you have a Falcon and want to use IDE devices (hard |
| 921 | disks, CD-ROM drives, etc.) that are connected to the builtin IDE |
| 922 | interface. |
| 923 | |
| 924 | config BLK_DEV_MAC_IDE |
| 925 | bool "Macintosh Quadra/Powerbook IDE interface support" |
| 926 | depends on MAC |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 927 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 928 | help |
| 929 | This is the IDE driver for the builtin IDE interface on some m68k |
| 930 | Macintosh models. It supports both the `Quadra style' (used in |
| 931 | Quadra/ Centris 630 and Performa 588 models) and `Powerbook style' |
| 932 | (used in the Powerbook 150 and 190 models) IDE interface. |
| 933 | |
| 934 | Say Y if you have such an Macintosh model and want to use IDE |
| 935 | devices (hard disks, CD-ROM drives, etc.) that are connected to the |
| 936 | builtin IDE interface. |
| 937 | |
| 938 | config BLK_DEV_Q40IDE |
| 939 | bool "Q40/Q60 IDE interface support" |
| 940 | depends on Q40 |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 941 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 942 | help |
| 943 | Enable the on-board IDE controller in the Q40/Q60. This should |
| 944 | normally be on; disable it only if you are running a custom hard |
| 945 | drive subsystem through an expansion card. |
| 946 | |
| 947 | config BLK_DEV_MPC8xx_IDE |
| 948 | bool "MPC8xx IDE support" |
Kumar Gala | dc4b6fd | 2007-09-11 22:28:33 +0200 | [diff] [blame^] | 949 | depends on 8xx && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE |
Bartlomiej Zolnierkiewicz | 2195dad | 2007-08-20 22:42:54 +0200 | [diff] [blame] | 950 | select IDE_GENERIC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 951 | help |
| 952 | This option provides support for IDE on Motorola MPC8xx Systems. |
| 953 | Please see 'Type of MPC8xx IDE interface' for details. |
| 954 | |
| 955 | If unsure, say N. |
| 956 | |
| 957 | choice |
| 958 | prompt "Type of MPC8xx IDE interface" |
| 959 | depends on BLK_DEV_MPC8xx_IDE |
| 960 | default IDE_8xx_PCCARD |
| 961 | |
| 962 | config IDE_8xx_PCCARD |
| 963 | bool "8xx_PCCARD" |
| 964 | ---help--- |
| 965 | Select how the IDE devices are connected to the MPC8xx system: |
| 966 | |
| 967 | 8xx_PCCARD uses the 8xx internal PCMCIA interface in combination |
| 968 | with a PC Card (e.g. ARGOSY portable Hard Disk Adapter), |
| 969 | ATA PC Card HDDs or ATA PC Flash Cards (example: TQM8xxL |
| 970 | systems) |
| 971 | |
| 972 | 8xx_DIRECT is used for directly connected IDE devices using the 8xx |
| 973 | internal PCMCIA interface (example: IVMS8 systems) |
| 974 | |
| 975 | EXT_DIRECT is used for IDE devices directly connected to the 8xx |
| 976 | bus using some glue logic, but _not_ the 8xx internal |
| 977 | PCMCIA interface (example: IDIF860 systems) |
| 978 | |
| 979 | config IDE_8xx_DIRECT |
| 980 | bool "8xx_DIRECT" |
| 981 | |
| 982 | config IDE_EXT_DIRECT |
| 983 | bool "EXT_DIRECT" |
| 984 | |
| 985 | endchoice |
| 986 | |
| 987 | # no isa -> no vlb |
| 988 | config IDE_CHIPSETS |
| 989 | bool "Other IDE chipset support" |
| 990 | depends on ISA |
| 991 | ---help--- |
| 992 | Say Y here if you want to include enhanced support for various IDE |
| 993 | interface chipsets used on motherboards and add-on cards. You can |
| 994 | then pick your particular IDE chip from among the following options. |
| 995 | This enhanced support may be necessary for Linux to be able to |
| 996 | access the 3rd/4th drives in some systems. It may also enable |
| 997 | setting of higher speed I/O rates to improve system performance with |
| 998 | these chipsets. Most of these also require special kernel boot |
| 999 | parameters to actually turn on the support at runtime; you can find |
| 1000 | a list of these in the file <file:Documentation/ide.txt>. |
| 1001 | |
| 1002 | People with SCSI-only systems can say N here. |
| 1003 | |
| 1004 | if IDE_CHIPSETS |
| 1005 | |
| 1006 | comment "Note: most of these also require special kernel boot parameters" |
| 1007 | |
| 1008 | config BLK_DEV_4DRIVES |
| 1009 | bool "Generic 4 drives/port support" |
| 1010 | help |
| 1011 | Certain older chipsets, including the Tekram 690CD, use a single set |
| 1012 | of I/O ports at 0x1f0 to control up to four drives, instead of the |
| 1013 | customary two drives per port. Support for this can be enabled at |
| 1014 | runtime using the "ide0=four" kernel boot parameter if you say Y |
| 1015 | here. |
| 1016 | |
| 1017 | config BLK_DEV_ALI14XX |
| 1018 | tristate "ALI M14xx support" |
| 1019 | help |
Bartlomiej Zolnierkiewicz | 8491388 | 2007-03-03 17:48:55 +0100 | [diff] [blame] | 1020 | This driver is enabled at runtime using the "ali14xx.probe" kernel |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1021 | boot parameter. It enables support for the secondary IDE interface |
| 1022 | of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster |
| 1023 | I/O speeds to be set as well. See the files |
| 1024 | <file:Documentation/ide.txt> and <file:drivers/ide/legacy/ali14xx.c> for |
| 1025 | more info. |
| 1026 | |
| 1027 | config BLK_DEV_DTC2278 |
| 1028 | tristate "DTC-2278 support" |
| 1029 | help |
Bartlomiej Zolnierkiewicz | 8491388 | 2007-03-03 17:48:55 +0100 | [diff] [blame] | 1030 | This driver is enabled at runtime using the "dtc2278.probe" kernel |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1031 | boot parameter. It enables support for the secondary IDE interface |
| 1032 | of the DTC-2278 card, and permits faster I/O speeds to be set as |
| 1033 | well. See the <file:Documentation/ide.txt> and |
| 1034 | <file:drivers/ide/legacy/dtc2278.c> files for more info. |
| 1035 | |
| 1036 | config BLK_DEV_HT6560B |
| 1037 | tristate "Holtek HT6560B support" |
| 1038 | help |
Bartlomiej Zolnierkiewicz | 8491388 | 2007-03-03 17:48:55 +0100 | [diff] [blame] | 1039 | This driver is enabled at runtime using the "ht6560b.probe" kernel |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1040 | boot parameter. It enables support for the secondary IDE interface |
| 1041 | of the Holtek card, and permits faster I/O speeds to be set as well. |
| 1042 | See the <file:Documentation/ide.txt> and |
| 1043 | <file:drivers/ide/legacy/ht6560b.c> files for more info. |
| 1044 | |
| 1045 | config BLK_DEV_QD65XX |
| 1046 | tristate "QDI QD65xx support" |
| 1047 | help |
Bartlomiej Zolnierkiewicz | 8491388 | 2007-03-03 17:48:55 +0100 | [diff] [blame] | 1048 | This driver is enabled at runtime using the "qd65xx.probe" kernel |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1049 | boot parameter. It permits faster I/O speeds to be set. See the |
| 1050 | <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for |
| 1051 | more info. |
| 1052 | |
| 1053 | config BLK_DEV_UMC8672 |
| 1054 | tristate "UMC-8672 support" |
| 1055 | help |
Bartlomiej Zolnierkiewicz | 8491388 | 2007-03-03 17:48:55 +0100 | [diff] [blame] | 1056 | This driver is enabled at runtime using the "umc8672.probe" kernel |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1057 | boot parameter. It enables support for the secondary IDE interface |
| 1058 | of the UMC-8672, and permits faster I/O speeds to be set as well. |
| 1059 | See the files <file:Documentation/ide.txt> and |
| 1060 | <file:drivers/ide/legacy/umc8672.c> for more info. |
| 1061 | |
| 1062 | endif |
| 1063 | |
| 1064 | config BLK_DEV_IDEDMA |
Pete Popov | 26a940e | 2005-09-15 08:03:12 +0000 | [diff] [blame] | 1065 | def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1066 | |
| 1067 | config IDEDMA_IVB |
| 1068 | bool "IGNORE word93 Validation BITS" |
| 1069 | depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS |
| 1070 | ---help--- |
| 1071 | There are unclear terms in ATA-4 and ATA-5 standards how certain |
| 1072 | hardware (an 80c ribbon) should be detected. Different interpretations |
| 1073 | of the standards have been released in hardware. This causes problems: |
| 1074 | for example, a host with Ultra Mode 4 (or higher) will not run |
| 1075 | in that mode with an 80c ribbon. |
| 1076 | |
| 1077 | If you are experiencing compatibility or performance problems, you |
Andreas Mohr | 3b6ce24 | 2006-02-03 03:04:54 -0800 | [diff] [blame] | 1078 | MAY try to answer Y here. However, it does not necessarily solve |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1079 | any of your problems, it could even cause more of them. |
| 1080 | |
| 1081 | It is normally safe to answer Y; however, the default is N. |
| 1082 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1083 | endif |
| 1084 | |
| 1085 | config BLK_DEV_HD_ONLY |
| 1086 | bool "Old hard disk (MFM/RLL/IDE) driver" |
| 1087 | depends on BLK_DEV_IDE=n |
| 1088 | help |
| 1089 | There are two drivers for MFM/RLL/IDE hard disks. Most people use |
| 1090 | the newer enhanced driver, but this old one is still around for two |
| 1091 | reasons. Some older systems have strange timing problems and seem to |
| 1092 | work only with the old driver (which itself does not work with some |
| 1093 | newer systems). The other reason is that the old driver is smaller, |
| 1094 | since it lacks the enhanced functionality of the new one. This makes |
| 1095 | it a good choice for systems with very tight memory restrictions, or |
| 1096 | for systems with only older MFM/RLL/ESDI drives. Choosing the old |
| 1097 | driver can save 13 KB or so of kernel memory. |
| 1098 | |
| 1099 | If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver |
| 1100 | instead of this one. For more detailed information, read the |
| 1101 | Disk-HOWTO, available from |
| 1102 | <http://www.tldp.org/docs.html#howto>. |
| 1103 | |
| 1104 | config BLK_DEV_HD |
| 1105 | def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY |
| 1106 | |
Jan Engelhardt | e0ff9cd | 2007-05-16 00:51:46 +0200 | [diff] [blame] | 1107 | endif # IDE |