blob: e408a3a89bbaf0568a7107bf00b90a861fdd10ab [file] [log] [blame]
eric miaoe1d9b952007-12-13 10:41:43 +08001/*
2 * linux/arch/arm/mach-pxa/littleton.c
3 *
4 * Support for the Marvell Littleton Development Platform.
5 *
6 * Author: Jason Chagas (largely modified code)
7 * Created: Nov 20, 2006
8 * Copyright: (C) Copyright 2006 Marvell International Ltd.
9 *
10 * 2007-11-22 modified to align with latest kernel
11 * eric miao <eric.miao@marvell.com>
12 *
13 * This program is free software; you can redistribute it and/or modify
14 * it under the terms of the GNU General Public License version 2 as
15 * publishhed by the Free Software Foundation.
16 */
17
18#include <linux/init.h>
19#include <linux/interrupt.h>
20#include <linux/delay.h>
21#include <linux/platform_device.h>
22#include <linux/clk.h>
23
24#include <asm/types.h>
25#include <asm/setup.h>
26#include <asm/memory.h>
27#include <asm/mach-types.h>
28#include <asm/hardware.h>
29#include <asm/irq.h>
30
31#include <asm/mach/arch.h>
32#include <asm/mach/map.h>
33#include <asm/mach/irq.h>
34
35#include <asm/arch/pxa-regs.h>
36#include <asm/arch/mfp-pxa300.h>
37#include <asm/arch/gpio.h>
38#include <asm/arch/pxafb.h>
39#include <asm/arch/ssp.h>
40#include <asm/arch/littleton.h>
41
42#include "generic.h"
43
44#define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)
45
46/* Littleton MFP configurations */
47static mfp_cfg_t littleton_mfp_cfg[] __initdata = {
48 /* LCD */
49 GPIO54_LCD_LDD_0,
50 GPIO55_LCD_LDD_1,
51 GPIO56_LCD_LDD_2,
52 GPIO57_LCD_LDD_3,
53 GPIO58_LCD_LDD_4,
54 GPIO59_LCD_LDD_5,
55 GPIO60_LCD_LDD_6,
56 GPIO61_LCD_LDD_7,
57 GPIO62_LCD_LDD_8,
58 GPIO63_LCD_LDD_9,
59 GPIO64_LCD_LDD_10,
60 GPIO65_LCD_LDD_11,
61 GPIO66_LCD_LDD_12,
62 GPIO67_LCD_LDD_13,
63 GPIO68_LCD_LDD_14,
64 GPIO69_LCD_LDD_15,
65 GPIO70_LCD_LDD_16,
66 GPIO71_LCD_LDD_17,
67 GPIO72_LCD_FCLK,
68 GPIO73_LCD_LCLK,
69 GPIO74_LCD_PCLK,
70 GPIO75_LCD_BIAS,
71
72 /* SSP2 */
73 GPIO25_SSP2_SCLK,
74 GPIO17_SSP2_FRM,
75 GPIO27_SSP2_TXD,
76
77 /* Debug Ethernet */
78 GPIO90_GPIO,
79};
80
81static struct resource smc91x_resources[] = {
82 [0] = {
83 .start = (LITTLETON_ETH_PHYS + 0x300),
84 .end = (LITTLETON_ETH_PHYS + 0xfffff),
85 .flags = IORESOURCE_MEM,
86 },
87 [1] = {
88 .start = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO90)),
89 .end = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO90)),
90 .flags = IORESOURCE_IRQ,
91 }
92};
93
94static struct platform_device smc91x_device = {
95 .name = "smc91x",
96 .id = 0,
97 .num_resources = ARRAY_SIZE(smc91x_resources),
98 .resource = smc91x_resources,
99};
100
101#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULES)
102/* use bit 30, 31 as the indicator of command parameter number */
103#define CMD0(x) ((0x00000000) | ((x) << 9))
104#define CMD1(x, x1) ((0x40000000) | ((x) << 9) | 0x100 | (x1))
105#define CMD2(x, x1, x2) ((0x80000000) | ((x) << 18) | 0x20000 |\
106 ((x1) << 9) | 0x100 | (x2))
107
108static uint32_t lcd_panel_reset[] = {
109 CMD0(0x1), /* reset */
110 CMD0(0x0), /* nop */
111 CMD0(0x0), /* nop */
112 CMD0(0x0), /* nop */
113};
114
115static uint32_t lcd_panel_on[] = {
116 CMD0(0x29), /* Display ON */
117 CMD2(0xB8, 0xFF, 0xF9), /* Output Control */
118 CMD0(0x11), /* Sleep out */
119 CMD1(0xB0, 0x16), /* Wake */
120};
121
122static uint32_t lcd_panel_off[] = {
123 CMD0(0x28), /* Display OFF */
124 CMD2(0xB8, 0x80, 0x02), /* Output Control */
125 CMD0(0x10), /* Sleep in */
126 CMD1(0xB0, 0x00), /* Deep stand by in */
127};
128
129static uint32_t lcd_vga_pass_through[] = {
130 CMD1(0xB0, 0x16),
131 CMD1(0xBC, 0x80),
132 CMD1(0xE1, 0x00),
133 CMD1(0x36, 0x50),
134 CMD1(0x3B, 0x00),
135};
136
137static uint32_t lcd_qvga_pass_through[] = {
138 CMD1(0xB0, 0x16),
139 CMD1(0xBC, 0x81),
140 CMD1(0xE1, 0x00),
141 CMD1(0x36, 0x50),
142 CMD1(0x3B, 0x22),
143};
144
145static uint32_t lcd_vga_transfer[] = {
146 CMD1(0xcf, 0x02), /* Blanking period control (1) */
147 CMD2(0xd0, 0x08, 0x04), /* Blanking period control (2) */
148 CMD1(0xd1, 0x01), /* CKV timing control on/off */
149 CMD2(0xd2, 0x14, 0x00), /* CKV 1,2 timing control */
150 CMD2(0xd3, 0x1a, 0x0f), /* OEV timing control */
151 CMD2(0xd4, 0x1f, 0xaf), /* ASW timing control (1) */
152 CMD1(0xd5, 0x14), /* ASW timing control (2) */
153 CMD0(0x21), /* Invert for normally black display */
154 CMD0(0x29), /* Display on */
155};
156
157static uint32_t lcd_qvga_transfer[] = {
158 CMD1(0xd6, 0x02), /* Blanking period control (1) */
159 CMD2(0xd7, 0x08, 0x04), /* Blanking period control (2) */
160 CMD1(0xd8, 0x01), /* CKV timing control on/off */
161 CMD2(0xd9, 0x00, 0x08), /* CKV 1,2 timing control */
162 CMD2(0xde, 0x05, 0x0a), /* OEV timing control */
163 CMD2(0xdf, 0x0a, 0x19), /* ASW timing control (1) */
164 CMD1(0xe0, 0x0a), /* ASW timing control (2) */
165 CMD0(0x21), /* Invert for normally black display */
166 CMD0(0x29), /* Display on */
167};
168
169static uint32_t lcd_panel_config[] = {
170 CMD2(0xb8, 0xff, 0xf9), /* Output control */
171 CMD0(0x11), /* sleep out */
172 CMD1(0xba, 0x01), /* Display mode (1) */
173 CMD1(0xbb, 0x00), /* Display mode (2) */
174 CMD1(0x3a, 0x60), /* Display mode 18-bit RGB */
175 CMD1(0xbf, 0x10), /* Drive system change control */
176 CMD1(0xb1, 0x56), /* Booster operation setup */
177 CMD1(0xb2, 0x33), /* Booster mode setup */
178 CMD1(0xb3, 0x11), /* Booster frequency setup */
179 CMD1(0xb4, 0x02), /* Op amp/system clock */
180 CMD1(0xb5, 0x35), /* VCS voltage */
181 CMD1(0xb6, 0x40), /* VCOM voltage */
182 CMD1(0xb7, 0x03), /* External display signal */
183 CMD1(0xbd, 0x00), /* ASW slew rate */
184 CMD1(0xbe, 0x00), /* Dummy data for QuadData operation */
185 CMD1(0xc0, 0x11), /* Sleep out FR count (A) */
186 CMD1(0xc1, 0x11), /* Sleep out FR count (B) */
187 CMD1(0xc2, 0x11), /* Sleep out FR count (C) */
188 CMD2(0xc3, 0x20, 0x40), /* Sleep out FR count (D) */
189 CMD2(0xc4, 0x60, 0xc0), /* Sleep out FR count (E) */
190 CMD2(0xc5, 0x10, 0x20), /* Sleep out FR count (F) */
191 CMD1(0xc6, 0xc0), /* Sleep out FR count (G) */
192 CMD2(0xc7, 0x33, 0x43), /* Gamma 1 fine tuning (1) */
193 CMD1(0xc8, 0x44), /* Gamma 1 fine tuning (2) */
194 CMD1(0xc9, 0x33), /* Gamma 1 inclination adjustment */
195 CMD1(0xca, 0x00), /* Gamma 1 blue offset adjustment */
196 CMD2(0xec, 0x01, 0xf0), /* Horizontal clock cycles */
197};
198
199static void ssp_reconfig(struct ssp_dev *dev, int nparam)
200{
201 static int last_nparam = -1;
202
203 /* check if it is necessary to re-config SSP */
204 if (nparam == last_nparam)
205 return;
206
207 ssp_disable(dev);
208 ssp_config(dev, (nparam == 2) ? 0x0010058a : 0x00100581, 0x18, 0, 0);
209
210 last_nparam = nparam;
211}
212
213static void ssp_send_cmd(uint32_t *cmd, int num)
214{
215 static int ssp_initialized;
216 static struct ssp_dev ssp2;
217
218 int i;
219
220 if (!ssp_initialized) {
221 ssp_init(&ssp2, 2, SSP_NO_IRQ);
222 ssp_initialized = 1;
223 }
224
225 clk_enable(ssp2.ssp->clk);
226 for (i = 0; i < num; i++, cmd++) {
227 ssp_reconfig(&ssp2, (*cmd >> 30) & 0x3);
228 ssp_write_word(&ssp2, *cmd & 0x3fffffff);
229
230 /* FIXME: ssp_flush() is mandatory here to work */
231 ssp_flush(&ssp2);
232 }
233 clk_disable(ssp2.ssp->clk);
234}
235
236static void littleton_lcd_power(int on, struct fb_var_screeninfo *var)
237{
238 if (on) {
239 ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_on));
240 ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_reset));
241 if (var->xres > 240) {
242 /* VGA */
243 ssp_send_cmd(ARRAY_AND_SIZE(lcd_vga_pass_through));
244 ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_config));
245 ssp_send_cmd(ARRAY_AND_SIZE(lcd_vga_transfer));
246 } else {
247 /* QVGA */
248 ssp_send_cmd(ARRAY_AND_SIZE(lcd_qvga_pass_through));
249 ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_config));
250 ssp_send_cmd(ARRAY_AND_SIZE(lcd_qvga_transfer));
251 }
252 } else
253 ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_off));
254}
255
256static struct pxafb_mode_info tpo_tdo24mtea1_modes[] = {
257 [0] = {
258 /* VGA */
259 .pixclock = 38250,
260 .xres = 480,
261 .yres = 640,
262 .bpp = 16,
263 .hsync_len = 8,
264 .left_margin = 8,
265 .right_margin = 24,
266 .vsync_len = 2,
267 .upper_margin = 2,
268 .lower_margin = 4,
269 .sync = 0,
270 },
271 [1] = {
272 /* QVGA */
273 .pixclock = 153000,
274 .xres = 240,
275 .yres = 320,
276 .bpp = 16,
277 .hsync_len = 8,
278 .left_margin = 8,
279 .right_margin = 88,
280 .vsync_len = 2,
281 .upper_margin = 2,
282 .lower_margin = 2,
283 .sync = 0,
284 },
285};
286
287static struct pxafb_mach_info littleton_lcd_info = {
288 .modes = tpo_tdo24mtea1_modes,
289 .num_modes = 2,
290 .lccr0 = LCCR0_Act,
291 .lccr3 = LCCR3_HSP | LCCR3_VSP,
292 .pxafb_lcd_power = littleton_lcd_power,
293};
294
295static void littleton_init_lcd(void)
296{
297 set_pxa_fb_info(&littleton_lcd_info);
298}
299#else
300static inline void littleton_init_lcd(void) {};
301#endif /* CONFIG_FB_PXA || CONFIG_FB_PXA_MODULES */
302
303static void __init littleton_init(void)
304{
305 /* initialize MFP configurations */
306 pxa3xx_mfp_config(ARRAY_AND_SIZE(littleton_mfp_cfg));
307
308 /*
309 * Note: we depend bootloader set the correct
310 * value to MSC register for SMC91x.
311 */
312 platform_device_register(&smc91x_device);
313
314 littleton_init_lcd();
315}
316
317MACHINE_START(LITTLETON, "Marvell Form Factor Development Platform (aka Littleton)")
318 .phys_io = 0x40000000,
319 .boot_params = 0xa0000100,
320 .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
321 .map_io = pxa_map_io,
322 .init_irq = pxa3xx_init_irq,
323 .timer = &pxa_timer,
324 .init_machine = littleton_init,
325MACHINE_END