blob: fd5fbd10aad07e853878ff53a3c5280dbc330bdc [file] [log] [blame]
Manuel Lauss0273b4e2009-10-04 14:55:29 +02001/*
2 * PCMCIA socket code for the MyCable XXS1500 system.
3 *
4 * Copyright (c) 2009 Manuel Lauss <manuel.lauss@gmail.com>
5 *
6 */
7
8#include <linux/delay.h>
9#include <linux/gpio.h>
10#include <linux/interrupt.h>
11#include <linux/io.h>
12#include <linux/ioport.h>
13#include <linux/mm.h>
14#include <linux/platform_device.h>
15#include <linux/pm.h>
16#include <linux/resource.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090017#include <linux/slab.h>
Manuel Lauss0273b4e2009-10-04 14:55:29 +020018#include <linux/spinlock.h>
19
Manuel Lauss0273b4e2009-10-04 14:55:29 +020020#include <pcmcia/ss.h>
21#include <pcmcia/cistpl.h>
22
23#include <asm/irq.h>
Manuel Lauss0273b4e2009-10-04 14:55:29 +020024#include <asm/mach-au1x00/au1000.h>
25
26#define MEM_MAP_SIZE 0x400000
27#define IO_MAP_SIZE 0x1000
28
29
30/*
31 * 3.3V cards only; all interfacing is done via gpios:
32 *
33 * 0/1: carddetect (00 = card present, xx = huh)
34 * 4: card irq
35 * 204: reset (high-act)
36 * 205: buffer enable (low-act)
37 * 208/209: card voltage key (00,01,10,11)
38 * 210: battwarn
39 * 211: batdead
40 * 214: power (low-act)
41 */
42#define GPIO_CDA 0
43#define GPIO_CDB 1
44#define GPIO_CARDIRQ 4
45#define GPIO_RESET 204
46#define GPIO_OUTEN 205
47#define GPIO_VSL 208
48#define GPIO_VSH 209
49#define GPIO_BATTDEAD 210
50#define GPIO_BATTWARN 211
51#define GPIO_POWER 214
52
53struct xxs1500_pcmcia_sock {
54 struct pcmcia_socket socket;
55 void *virt_io;
56
Manuel Lauss11b897c2010-02-24 17:40:21 +010057 phys_addr_t phys_io;
58 phys_addr_t phys_attr;
59 phys_addr_t phys_mem;
Manuel Lauss0273b4e2009-10-04 14:55:29 +020060
61 /* previous flags for set_socket() */
62 unsigned int old_flags;
63};
64
65#define to_xxs_socket(x) container_of(x, struct xxs1500_pcmcia_sock, socket)
66
67static irqreturn_t cdirq(int irq, void *data)
68{
69 struct xxs1500_pcmcia_sock *sock = data;
70
71 pcmcia_parse_events(&sock->socket, SS_DETECT);
72
73 return IRQ_HANDLED;
74}
75
76static int xxs1500_pcmcia_configure(struct pcmcia_socket *skt,
77 struct socket_state_t *state)
78{
79 struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
80 unsigned int changed;
81
82 /* power control */
83 switch (state->Vcc) {
84 case 0:
85 gpio_set_value(GPIO_POWER, 1); /* power off */
86 break;
87 case 33:
88 gpio_set_value(GPIO_POWER, 0); /* power on */
89 break;
90 case 50:
91 default:
92 return -EINVAL;
93 }
94
95 changed = state->flags ^ sock->old_flags;
96
97 if (changed & SS_RESET) {
98 if (state->flags & SS_RESET) {
99 gpio_set_value(GPIO_RESET, 1); /* assert reset */
100 gpio_set_value(GPIO_OUTEN, 1); /* buffers off */
101 } else {
102 gpio_set_value(GPIO_RESET, 0); /* deassert reset */
103 gpio_set_value(GPIO_OUTEN, 0); /* buffers on */
104 msleep(500);
105 }
106 }
107
108 sock->old_flags = state->flags;
109
110 return 0;
111}
112
113static int xxs1500_pcmcia_get_status(struct pcmcia_socket *skt,
114 unsigned int *value)
115{
116 unsigned int status;
117 int i;
118
119 status = 0;
120
121 /* check carddetects: GPIO[0:1] must both be low */
122 if (!gpio_get_value(GPIO_CDA) && !gpio_get_value(GPIO_CDB))
123 status |= SS_DETECT;
124
125 /* determine card voltage: GPIO[208:209] binary value */
126 i = (!!gpio_get_value(GPIO_VSL)) | ((!!gpio_get_value(GPIO_VSH)) << 1);
127
128 switch (i) {
129 case 0:
130 case 1:
131 case 2:
132 status |= SS_3VCARD; /* 3V card */
133 break;
134 case 3: /* 5V card, unsupported */
135 default:
136 status |= SS_XVCARD; /* treated as unsupported in core */
137 }
138
139 /* GPIO214: low active power switch */
140 status |= gpio_get_value(GPIO_POWER) ? 0 : SS_POWERON;
141
142 /* GPIO204: high-active reset line */
143 status |= gpio_get_value(GPIO_RESET) ? SS_RESET : SS_READY;
144
145 /* other stuff */
146 status |= gpio_get_value(GPIO_BATTDEAD) ? 0 : SS_BATDEAD;
147 status |= gpio_get_value(GPIO_BATTWARN) ? 0 : SS_BATWARN;
148
149 *value = status;
150
151 return 0;
152}
153
154static int xxs1500_pcmcia_sock_init(struct pcmcia_socket *skt)
155{
156 gpio_direction_input(GPIO_CDA);
157 gpio_direction_input(GPIO_CDB);
158 gpio_direction_input(GPIO_VSL);
159 gpio_direction_input(GPIO_VSH);
160 gpio_direction_input(GPIO_BATTDEAD);
161 gpio_direction_input(GPIO_BATTWARN);
162 gpio_direction_output(GPIO_RESET, 1); /* assert reset */
163 gpio_direction_output(GPIO_OUTEN, 1); /* disable buffers */
164 gpio_direction_output(GPIO_POWER, 1); /* power off */
165
166 return 0;
167}
168
169static int xxs1500_pcmcia_sock_suspend(struct pcmcia_socket *skt)
170{
171 return 0;
172}
173
174static int au1x00_pcmcia_set_io_map(struct pcmcia_socket *skt,
175 struct pccard_io_map *map)
176{
177 struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
178
179 map->start = (u32)sock->virt_io;
180 map->stop = map->start + IO_MAP_SIZE;
181
182 return 0;
183}
184
185static int au1x00_pcmcia_set_mem_map(struct pcmcia_socket *skt,
186 struct pccard_mem_map *map)
187{
188 struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
189
190 if (map->flags & MAP_ATTRIB)
191 map->static_start = sock->phys_attr + map->card_start;
192 else
193 map->static_start = sock->phys_mem + map->card_start;
194
195 return 0;
196}
197
198static struct pccard_operations xxs1500_pcmcia_operations = {
199 .init = xxs1500_pcmcia_sock_init,
200 .suspend = xxs1500_pcmcia_sock_suspend,
201 .get_status = xxs1500_pcmcia_get_status,
202 .set_socket = xxs1500_pcmcia_configure,
203 .set_io_map = au1x00_pcmcia_set_io_map,
204 .set_mem_map = au1x00_pcmcia_set_mem_map,
205};
206
207static int __devinit xxs1500_pcmcia_probe(struct platform_device *pdev)
208{
209 struct xxs1500_pcmcia_sock *sock;
210 struct resource *r;
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200211 int ret, irq;
212
213 sock = kzalloc(sizeof(struct xxs1500_pcmcia_sock), GFP_KERNEL);
214 if (!sock)
215 return -ENOMEM;
216
217 ret = -ENODEV;
218
Manuel Laussf25e1882010-03-01 21:40:56 +0100219 /* 36bit PCMCIA Attribute area address */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100220 r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-attr");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200221 if (!r) {
Manuel Lauss11b897c2010-02-24 17:40:21 +0100222 dev_err(&pdev->dev, "missing 'pcmcia-attr' resource!\n");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200223 goto out0;
224 }
225 sock->phys_attr = r->start;
226
Manuel Laussf25e1882010-03-01 21:40:56 +0100227 /* 36bit PCMCIA Memory area address */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100228 r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-mem");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200229 if (!r) {
Manuel Lauss11b897c2010-02-24 17:40:21 +0100230 dev_err(&pdev->dev, "missing 'pcmcia-mem' resource!\n");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200231 goto out0;
232 }
233 sock->phys_mem = r->start;
234
Manuel Laussf25e1882010-03-01 21:40:56 +0100235 /* 36bit PCMCIA IO area address */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100236 r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-io");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200237 if (!r) {
Manuel Lauss11b897c2010-02-24 17:40:21 +0100238 dev_err(&pdev->dev, "missing 'pcmcia-io' resource!\n");
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200239 goto out0;
240 }
241 sock->phys_io = r->start;
242
243
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200244 /*
245 * PCMCIA client drivers use the inb/outb macros to access
246 * the IO registers. Since mips_io_port_base is added
247 * to the access address of the mips implementation of
248 * inb/outb, we need to subtract it here because we want
249 * to access the I/O or MEM address directly, without
250 * going through this "mips_io_port_base" mechanism.
251 */
Manuel Lauss11b897c2010-02-24 17:40:21 +0100252 sock->virt_io = (void *)(ioremap(sock->phys_io, IO_MAP_SIZE) -
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200253 mips_io_port_base);
254
255 if (!sock->virt_io) {
256 dev_err(&pdev->dev, "cannot remap IO area\n");
257 ret = -ENOMEM;
258 goto out0;
259 }
260
261 sock->socket.ops = &xxs1500_pcmcia_operations;
262 sock->socket.owner = THIS_MODULE;
263 sock->socket.pci_irq = gpio_to_irq(GPIO_CARDIRQ);
264 sock->socket.features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
265 sock->socket.map_size = MEM_MAP_SIZE;
266 sock->socket.io_offset = (unsigned long)sock->virt_io;
267 sock->socket.dev.parent = &pdev->dev;
268 sock->socket.resource_ops = &pccard_static_ops;
269
270 platform_set_drvdata(pdev, sock);
271
272 /* setup carddetect irq: use one of the 2 GPIOs as an
273 * edge detector.
274 */
275 irq = gpio_to_irq(GPIO_CDA);
Thomas Gleixnerdced35a2011-03-28 17:49:12 +0200276 irq_set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200277 ret = request_irq(irq, cdirq, 0, "pcmcia_carddetect", sock);
278 if (ret) {
279 dev_err(&pdev->dev, "cannot setup cd irq\n");
280 goto out1;
281 }
282
283 ret = pcmcia_register_socket(&sock->socket);
284 if (ret) {
285 dev_err(&pdev->dev, "failed to register\n");
286 goto out2;
287 }
288
289 printk(KERN_INFO "MyCable XXS1500 PCMCIA socket services\n");
290
291 return 0;
292
293out2:
294 free_irq(gpio_to_irq(GPIO_CDA), sock);
295out1:
296 iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
297out0:
298 kfree(sock);
299 return ret;
300}
301
302static int __devexit xxs1500_pcmcia_remove(struct platform_device *pdev)
303{
304 struct xxs1500_pcmcia_sock *sock = platform_get_drvdata(pdev);
305
306 pcmcia_unregister_socket(&sock->socket);
307 free_irq(gpio_to_irq(GPIO_CDA), sock);
308 iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
309 kfree(sock);
310
311 return 0;
312}
313
314static struct platform_driver xxs1500_pcmcia_socket_driver = {
315 .driver = {
316 .name = "xxs1500_pcmcia",
317 .owner = THIS_MODULE,
318 },
319 .probe = xxs1500_pcmcia_probe,
320 .remove = __devexit_p(xxs1500_pcmcia_remove),
321};
322
Axel Lin5d95f8e22011-11-27 12:53:06 +0800323module_platform_driver(xxs1500_pcmcia_socket_driver);
Manuel Lauss0273b4e2009-10-04 14:55:29 +0200324
325MODULE_LICENSE("GPL");
326MODULE_DESCRIPTION("PCMCIA Socket Services for MyCable XXS1500 systems");
327MODULE_AUTHOR("Manuel Lauss");