blob: 611f5a5499b153c9594ad37e7237f7a35489b3bd [file] [log] [blame]
Bernhard Kaindlf212ec42008-01-30 13:34:11 +01001
2 Using physical DMA provided by OHCI-1394 FireWire controllers for debugging
3 ---------------------------------------------------------------------------
4
5Introduction
6------------
7
8Basically all FireWire controllers which are in use today are compliant
9to the OHCI-1394 specification which defines the controller to be a PCI
10bus master which uses DMA to offload data transfers from the CPU and has
11a "Physical Response Unit" which executes specific requests by employing
12PCI-Bus master DMA after applying filters defined by the OHCI-1394 driver.
13
14Once properly configured, remote machines can send these requests to
15ask the OHCI-1394 controller to perform read and write requests on
16physical system memory and, for read requests, send the result of
17the physical memory read back to the requester.
18
19With that, it is possible to debug issues by reading interesting memory
20locations such as buffers like the printk buffer or the process table.
21
22Retrieving a full system memory dump is also possible over the FireWire,
23using data transfer rates in the order of 10MB/s or more.
24
25Memory access is currently limited to the low 4G of physical address
26space which can be a problem on IA64 machines where memory is located
27mostly above that limit, but it is rarely a problem on more common
28hardware such as hardware based on x86, x86-64 and PowerPC.
29
30Together with a early initialization of the OHCI-1394 controller for debugging,
31this facility proved most useful for examining long debugs logs in the printk
32buffer on to debug early boot problems in areas like ACPI where the system
33fails to boot and other means for debugging (serial port) are either not
34available (notebooks) or too slow for extensive debug information (like ACPI).
35
36Drivers
37-------
38
Stefan Richter09d73282008-02-18 21:38:35 +010039The ohci1394 driver in drivers/ieee1394 initializes the OHCI-1394 controllers
40to a working state and enables physical DMA by default for all remote nodes.
41This can be turned off by ohci1394's module parameter phys_dma=0.
Bernhard Kaindlf212ec42008-01-30 13:34:11 +010042
Stefan Richter09d73282008-02-18 21:38:35 +010043The alternative firewire-ohci driver in drivers/firewire uses filtered physical
Stefan Richter080de8c2008-02-28 20:54:43 +010044DMA by default, which is more secure but not suitable for remote debugging.
45Compile the driver with CONFIG_FIREWIRE_OHCI_REMOTE_DMA (Kernel hacking menu:
46Remote debugging over FireWire with firewire-ohci) to get unfiltered physical
47DMA.
Stefan Richter09d73282008-02-18 21:38:35 +010048
Stefan Richter080de8c2008-02-28 20:54:43 +010049Because ohci1394 and firewire-ohci depend on the PCI enumeration to be
50completed, an initialization routine which runs pretty early has been
51implemented for x86. This routine runs long before console_init() can be
52called, i.e. before the printk buffer appears on the console.
Bernhard Kaindlf212ec42008-01-30 13:34:11 +010053
54To activate it, enable CONFIG_PROVIDE_OHCI1394_DMA_INIT (Kernel hacking menu:
Stefan Richter080de8c2008-02-28 20:54:43 +010055Remote debugging over FireWire early on boot) and pass the parameter
56"ohci1394_dma=early" to the recompiled kernel on boot.
Bernhard Kaindlf212ec42008-01-30 13:34:11 +010057
58Tools
59-----
60
61firescope - Originally developed by Benjamin Herrenschmidt, Andi Kleen ported
62it from PowerPC to x86 and x86_64 and added functionality, firescope can now
63be used to view the printk buffer of a remote machine, even with live update.
64
65Bernhard Kaindl enhanced firescope to support accessing 64-bit machines
66from 32-bit firescope and vice versa:
Justin P. Mattock211a6412009-09-29 15:13:58 -070067- http://halobates.de/firewire/firescope-0.2.2.tar.bz2
Bernhard Kaindlf212ec42008-01-30 13:34:11 +010068
69and he implemented fast system dump (alpha version - read README.txt):
Justin P. Mattock211a6412009-09-29 15:13:58 -070070- http://halobates.de/firewire/firedump-0.1.tar.bz2
Bernhard Kaindlf212ec42008-01-30 13:34:11 +010071
72There is also a gdb proxy for firewire which allows to use gdb to access
73data which can be referenced from symbols found by gdb in vmlinux:
Justin P. Mattock211a6412009-09-29 15:13:58 -070074- http://halobates.de/firewire/fireproxy-0.33.tar.bz2
Bernhard Kaindlf212ec42008-01-30 13:34:11 +010075
76The latest version of this gdb proxy (fireproxy-0.34) can communicate (not
77yet stable) with kgdb over an memory-based communication module (kgdbom).
78
79Getting Started
80---------------
81
82The OHCI-1394 specification regulates that the OHCI-1394 controller must
83disable all physical DMA on each bus reset.
84
85This means that if you want to debug an issue in a system state where
86interrupts are disabled and where no polling of the OHCI-1394 controller
87for bus resets takes place, you have to establish any FireWire cable
88connections and fully initialize all FireWire hardware __before__ the
89system enters such state.
90
91Step-by-step instructions for using firescope with early OHCI initialization:
92
931) Verify that your hardware is supported:
94
95 Load the ohci1394 or the fw-ohci module and check your kernel logs.
96 You should see a line similar to
97
98 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[fe9ff800-fe9fffff]
99 ... Max Packet=[2048] IR/IT contexts=[4/8]
100
101 when loading the driver. If you have no supported controller, many PCI,
102 CardBus and even some Express cards which are fully compliant to OHCI-1394
103 specification are available. If it requires no driver for Windows operating
104 systems, it most likely is. Only specialized shops have cards which are not
105 compliant, they are based on TI PCILynx chips and require drivers for Win-
106 dows operating systems.
107
1082) Establish a working FireWire cable connection:
109
110 Any FireWire cable, as long at it provides electrically and mechanically
111 stable connection and has matching connectors (there are small 4-pin and
112 large 6-pin FireWire ports) will do.
113
114 If an driver is running on both machines you should see a line like
115
116 ieee1394: Node added: ID:BUS[0-01:1023] GUID[0090270001b84bba]
117
118 on both machines in the kernel log when the cable is plugged in
119 and connects the two machines.
120
1213) Test physical DMA using firescope:
122
123 On the debug host,
124 - load the raw1394 module,
125 - make sure that /dev/raw1394 is accessible,
126 then start firescope:
127
128 $ firescope
129 Port 0 (ohci1394) opened, 2 nodes detected
130
131 FireScope
132 ---------
133 Target : <unspecified>
134 Gen : 1
135 [Ctrl-T] choose target
136 [Ctrl-H] this menu
137 [Ctrl-Q] quit
138
139 ------> Press Ctrl-T now, the output should be similar to:
140
141 2 nodes available, local node is: 0
142 0: ffc0, uuid: 00000000 00000000 [LOCAL]
143 1: ffc1, uuid: 00279000 ba4bb801
144
145 Besides the [LOCAL] node, it must show another node without error message.
146
1474) Prepare for debugging with early OHCI-1394 initialization:
148
149 4.1) Kernel compilation and installation on debug target
150
151 Compile the kernel to be debugged with CONFIG_PROVIDE_OHCI1394_DMA_INIT
152 (Kernel hacking: Provide code for enabling DMA over FireWire early on boot)
153 enabled and install it on the machine to be debugged (debug target).
154
155 4.2) Transfer the System.map of the debugged kernel to the debug host
156
157 Copy the System.map of the kernel be debugged to the debug host (the host
158 which is connected to the debugged machine over the FireWire cable).
159
1605) Retrieving the printk buffer contents:
161
162 With the FireWire cable connected, the OHCI-1394 driver on the debugging
163 host loaded, reboot the debugged machine, booting the kernel which has
164 CONFIG_PROVIDE_OHCI1394_DMA_INIT enabled, with the option ohci1394_dma=early.
165
166 Then, on the debugging host, run firescope, for example by using -A:
167
168 firescope -A System.map-of-debug-target-kernel
169
170 Note: -A automatically attaches to the first non-local node. It only works
171 reliably if only connected two machines are connected using FireWire.
172
173 After having attached to the debug target, press Ctrl-D to view the
174 complete printk buffer or Ctrl-U to enter auto update mode and get an
175 updated live view of recent kernel messages logged on the debug target.
176
177 Call "firescope -h" to get more information on firescope's options.
178
179Notes
180-----
Justin P. Mattock211a6412009-09-29 15:13:58 -0700181Documentation and specifications: http://halobates.de/firewire/
Bernhard Kaindlf212ec42008-01-30 13:34:11 +0100182
183FireWire is a trademark of Apple Inc. - for more information please refer to:
184http://en.wikipedia.org/wiki/FireWire