Dmitry Lifshitz | fb45105 | 2014-01-12 15:22:54 +0200 | [diff] [blame] | 1 | /* |
| 2 | * Support for CompuLab CM-T3517 |
| 3 | */ |
| 4 | /dts-v1/; |
| 5 | |
| 6 | #include "am3517.dtsi" |
| 7 | #include "omap3-cm-t3x.dtsi" |
| 8 | |
| 9 | / { |
| 10 | model = "CompuLab CM-T3517"; |
| 11 | compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; |
| 12 | |
| 13 | vmmc: regulator-vmmc { |
| 14 | compatible = "regulator-fixed"; |
| 15 | regulator-name = "vmmc"; |
| 16 | regulator-min-microvolt = <3300000>; |
| 17 | regulator-max-microvolt = <3300000>; |
| 18 | }; |
| 19 | |
| 20 | wl12xx_vmmc2: wl12xx_vmmc2 { |
| 21 | compatible = "regulator-fixed"; |
| 22 | regulator-name = "vw1271"; |
| 23 | pinctrl-names = "default"; |
| 24 | pinctrl-0 = < |
| 25 | &wl12xx_wkup_pins |
| 26 | &wl12xx_core_pins |
| 27 | >; |
| 28 | regulator-min-microvolt = <1800000>; |
| 29 | regulator-max-microvolt = <1800000>; |
| 30 | gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */ |
| 31 | startup-delay-us = <20000>; |
| 32 | enable-active-high; |
| 33 | }; |
| 34 | |
| 35 | wl12xx_vaux2: wl12xx_vaux2 { |
| 36 | compatible = "regulator-fixed"; |
| 37 | regulator-name = "vwl1271_vaux2"; |
| 38 | regulator-min-microvolt = <1800000>; |
| 39 | regulator-max-microvolt = <1800000>; |
| 40 | }; |
| 41 | }; |
| 42 | |
| 43 | &omap3_pmx_wkup { |
| 44 | |
| 45 | wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins { |
| 46 | pinctrl-single,pins = < |
| 47 | OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ |
| 48 | OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */ |
| 49 | >; |
| 50 | }; |
| 51 | }; |
| 52 | |
| 53 | &omap3_pmx_core { |
| 54 | |
| 55 | phy1_reset_pins: pinmux_hsusb1_phy_reset_pins { |
| 56 | pinctrl-single,pins = < |
| 57 | OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */ |
| 58 | >; |
| 59 | }; |
| 60 | |
| 61 | phy2_reset_pins: pinmux_hsusb2_phy_reset_pins { |
| 62 | pinctrl-single,pins = < |
| 63 | OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */ |
| 64 | >; |
| 65 | }; |
| 66 | |
| 67 | otg_drv_vbus: pinmux_otg_drv_vbus { |
| 68 | pinctrl-single,pins = < |
| 69 | OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */ |
| 70 | >; |
| 71 | }; |
| 72 | |
| 73 | mmc2_pins: pinmux_mmc2_pins { |
| 74 | pinctrl-single,pins = < |
| 75 | OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ |
| 76 | OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ |
| 77 | OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ |
| 78 | OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ |
| 79 | OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ |
| 80 | OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ |
| 81 | >; |
| 82 | }; |
| 83 | |
| 84 | wl12xx_core_pins: pinmux_wl12xx_core_pins { |
| 85 | pinctrl-single,pins = < |
| 86 | OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ |
| 87 | OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */ |
| 88 | >; |
| 89 | }; |
| 90 | |
| 91 | usb_hub_pins: pinmux_usb_hub_pins { |
| 92 | pinctrl-single,pins = < |
| 93 | OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */ |
| 94 | >; |
| 95 | }; |
| 96 | }; |
| 97 | |
| 98 | &hsusb1_phy { |
| 99 | pinctrl-names = "default"; |
| 100 | pinctrl-0 = <&phy1_reset_pins>; |
| 101 | reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>; |
| 102 | }; |
| 103 | |
| 104 | &hsusb2_phy { |
| 105 | pinctrl-names = "default"; |
| 106 | pinctrl-0 = <&phy2_reset_pins>; |
| 107 | reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; |
| 108 | }; |
| 109 | |
| 110 | &davinci_emac { |
| 111 | status = "okay"; |
| 112 | }; |
| 113 | |
| 114 | &davinci_mdio { |
| 115 | status = "okay"; |
| 116 | }; |
| 117 | |
| 118 | &am35x_otg_hs { |
| 119 | status = "okay"; |
| 120 | pinctrl-names = "default"; |
| 121 | pinctrl-0 = <&otg_drv_vbus>; |
| 122 | }; |
| 123 | |
| 124 | &mmc1 { |
| 125 | vmmc-supply = <&vmmc>; |
| 126 | }; |
| 127 | |
| 128 | &mmc2 { |
| 129 | pinctrl-names = "default"; |
| 130 | pinctrl-0 = <&mmc2_pins>; |
| 131 | vmmc-supply = <&wl12xx_vmmc2>; |
| 132 | vmmc_aux-supply = <&wl12xx_vaux2>; |
| 133 | non-removable; |
| 134 | bus-width = <4>; |
| 135 | cap-power-off-card; |
| 136 | }; |