blob: d1458496520e7ec49ec278cde6d1ff32cbcc7008 [file] [log] [blame]
Dmitry Lifshitz40ecc022014-01-12 15:22:53 +02001/*
2 * Support for CompuLab CM-T3530
3 */
4/dts-v1/;
5
6#include "omap34xx.dtsi"
7#include "omap3-cm-t3x30.dtsi"
8
9/ {
10 model = "CompuLab CM-T3530";
11 compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
Stefan Roesee1902bb2014-03-12 11:49:12 +010012
13 /* Regulator to trigger the reset signal of the Wifi module */
14 mmc2_sdio_reset: regulator-mmc2-sdio-reset {
15 compatible = "regulator-fixed";
16 regulator-name = "regulator-mmc2-sdio-reset";
17 regulator-min-microvolt = <3300000>;
18 regulator-max-microvolt = <3300000>;
19 gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>;
20 enable-active-high;
21 };
22};
23
24&omap3_pmx_core {
25 mmc2_pins: pinmux_mmc2_pins {
26 pinctrl-single,pins = <
27 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
28 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
29 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
30 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
31 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
32 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
33 OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */
34 OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */
35 OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */
36 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */
37 >;
38 };
39};
40
41&mmc2 {
42 pinctrl-names = "default";
43 pinctrl-0 = <&mmc2_pins>;
44 vmmc-supply = <&mmc2_sdio_reset>;
45 non-removable;
46 bus-width = <4>;
47 cap-power-off-card;
Dmitry Lifshitz40ecc022014-01-12 15:22:53 +020048};