blob: 2035417fc1ab9d0e7bbc7574c2f66b914ba7ce94 [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
2 * pata_ali.c - ALI 15x3 PATA for new ATA layer
3 * (C) 2005 Red Hat Inc
4 * Alan Cox <alan@redhat.com>
5 *
6 * based in part upon
7 * linux/drivers/ide/pci/alim15x3.c Version 0.17 2003/01/02
8 *
9 * Copyright (C) 1998-2000 Michel Aubry, Maintainer
10 * Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
11 * Copyright (C) 1999-2000 CJ, cjtsai@ali.com.tw, Maintainer
12 *
13 * Copyright (C) 1998-2000 Andre Hedrick (andre@linux-ide.org)
14 * May be copied or modified under the terms of the GNU General Public License
15 * Copyright (C) 2002 Alan Cox <alan@redhat.com>
16 * ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw>
17 *
18 * Documentation
19 * Chipset documentation available under NDA only
20 *
21 * TODO/CHECK
22 * Cannot have ATAPI on both master & slave for rev < c2 (???) but
23 * otherwise should do atapi DMA.
24 */
25
26#include <linux/kernel.h>
27#include <linux/module.h>
28#include <linux/pci.h>
29#include <linux/init.h>
30#include <linux/blkdev.h>
31#include <linux/delay.h>
32#include <scsi/scsi_host.h>
33#include <linux/libata.h>
34#include <linux/dmi.h>
35
36#define DRV_NAME "pata_ali"
Alan8e42a5a2006-12-04 16:36:05 +000037#define DRV_VERSION "0.7.2"
Jeff Garzik669a5db2006-08-29 18:12:40 -040038
39/*
40 * Cable special cases
41 */
42
43static struct dmi_system_id cable_dmi_table[] = {
44 {
45 .ident = "HP Pavilion N5430",
46 .matches = {
47 DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
48 DMI_MATCH(DMI_BOARD_NAME, "OmniBook N32N-736"),
49 },
50 },
51 { }
52};
53
54static int ali_cable_override(struct pci_dev *pdev)
55{
56 /* Fujitsu P2000 */
57 if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF)
58 return 1;
59 /* Systems by DMI */
60 if (dmi_check_system(cable_dmi_table))
61 return 1;
62 return 0;
63}
64
65/**
66 * ali_c2_cable_detect - cable detection
67 * @ap: ATA port
68 *
69 * Perform cable detection for C2 and later revisions
70 */
71
72static int ali_c2_cable_detect(struct ata_port *ap)
73{
74 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
75 u8 ata66;
76
77 /* Certain laptops use short but suitable cables and don't
78 implement the detect logic */
79
80 if (ali_cable_override(pdev))
Alan Coxfc085152006-10-10 14:28:11 -070081 return ATA_CBL_PATA40_SHORT;
Jeff Garzik669a5db2006-08-29 18:12:40 -040082
83 /* Host view cable detect 0x4A bit 0 primary bit 1 secondary
84 Bit set for 40 pin */
85 pci_read_config_byte(pdev, 0x4A, &ata66);
86 if (ata66 & (1 << ap->port_no))
87 return ATA_CBL_PATA40;
88 else
89 return ATA_CBL_PATA80;
90}
91
92/**
93 * ali_early_error_handler - reset for eary chip
94 * @ap: ATA port
95 *
96 * Handle the reset callback for the later chips with cable detect
97 */
98
99static int ali_c2_pre_reset(struct ata_port *ap)
100{
101 ap->cbl = ali_c2_cable_detect(ap);
102 return ata_std_prereset(ap);
103}
104
105static void ali_c2_error_handler(struct ata_port *ap)
106{
107 ata_bmdma_drive_eh(ap, ali_c2_pre_reset,
108 ata_std_softreset, NULL,
109 ata_std_postreset);
110}
111
112/**
113 * ali_early_cable_detect - cable detection
114 * @ap: ATA port
115 *
116 * Perform cable detection for older chipsets. This turns out to be
117 * rather easy to implement
118 */
119
120static int ali_early_cable_detect(struct ata_port *ap)
121{
122 return ATA_CBL_PATA40;
123}
124
125/**
126 * ali_early_probe_init - reset for early chip
127 * @ap: ATA port
128 *
129 * Handle the reset callback for the early (pre cable detect) chips.
130 */
131
132static int ali_early_pre_reset(struct ata_port *ap)
133{
134 ap->cbl = ali_early_cable_detect(ap);
135 return ata_std_prereset(ap);
136}
137
138static void ali_early_error_handler(struct ata_port *ap)
139{
140 return ata_bmdma_drive_eh(ap, ali_early_pre_reset,
141 ata_std_softreset, NULL,
142 ata_std_postreset);
143}
144
145/**
146 * ali_20_filter - filter for earlier ALI DMA
147 * @ap: ALi ATA port
148 * @adev: attached device
149 *
150 * Ensure that we do not do DMA on CD devices. We may be able to
151 * fix that later on. Also ensure we do not do UDMA on WDC drives
152 */
153
154static unsigned long ali_20_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
155{
156 char model_num[40];
157 /* No DMA on anything but a disk for now */
158 if (adev->class != ATA_DEV_ATA)
159 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
160 ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
161 if (strstr(model_num, "WDC"))
162 return mask &= ~ATA_MASK_UDMA;
163 return ata_pci_default_filter(ap, adev, mask);
164}
165
166/**
167 * ali_fifo_control - FIFO manager
168 * @ap: ALi channel to control
169 * @adev: device for FIFO control
170 * @on: 0 for off 1 for on
171 *
172 * Enable or disable the FIFO on a given device. Because of the way the
173 * ALi FIFO works it provides a boost on ATA disk but can be confused by
174 * ATAPI and we must therefore manage it.
175 */
176
177static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int on)
178{
179 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
180 int pio_fifo = 0x54 + ap->port_no;
181 u8 fifo;
182 int shift = 4 * adev->devno;
183
184 /* ATA - FIFO on set nibble to 0x05, ATAPI - FIFO off, set nibble to
185 0x00. Not all the docs agree but the behaviour we now use is the
186 one stated in the BIOS Programming Guide */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400187
Jeff Garzik669a5db2006-08-29 18:12:40 -0400188 pci_read_config_byte(pdev, pio_fifo, &fifo);
189 fifo &= ~(0x0F << shift);
190 if (on)
191 fifo |= (on << shift);
192 pci_write_config_byte(pdev, pio_fifo, fifo);
193}
194
195/**
196 * ali_program_modes - load mode registers
197 * @ap: ALi channel to load
198 * @adev: Device the timing is for
199 * @cmd: Command timing
200 * @data: Data timing
201 * @ultra: UDMA timing or zero for off
202 *
203 * Loads the timing registers for cmd/data and disable UDMA if
204 * ultra is zero. If ultra is set then load and enable the UDMA
205 * timing but do not touch the command/data timing.
206 */
207
208static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, struct ata_timing *t, u8 ultra)
209{
210 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
211 int cas = 0x58 + 4 * ap->port_no; /* Command timing */
212 int cbt = 0x59 + 4 * ap->port_no; /* Command timing */
213 int drwt = 0x5A + 4 * ap->port_no + adev->devno; /* R/W timing */
214 int udmat = 0x56 + ap->port_no; /* UDMA timing */
215 int shift = 4 * adev->devno;
216 u8 udma;
217
218 if (t != NULL) {
219 t->setup = FIT(t->setup, 1, 8) & 7;
220 t->act8b = FIT(t->act8b, 1, 8) & 7;
221 t->rec8b = FIT(t->rec8b, 1, 16) & 15;
222 t->active = FIT(t->active, 1, 8) & 7;
223 t->recover = FIT(t->recover, 1, 16) & 15;
224
225 pci_write_config_byte(pdev, cas, t->setup);
226 pci_write_config_byte(pdev, cbt, (t->act8b << 4) | t->rec8b);
227 pci_write_config_byte(pdev, drwt, (t->active << 4) | t->recover);
228 }
229
230 /* Set up the UDMA enable */
231 pci_read_config_byte(pdev, udmat, &udma);
232 udma &= ~(0x0F << shift);
233 udma |= ultra << shift;
234 pci_write_config_byte(pdev, udmat, udma);
235}
236
237/**
238 * ali_set_piomode - set initial PIO mode data
239 * @ap: ATA interface
240 * @adev: ATA device
241 *
242 * Program the ALi registers for PIO mode. FIXME: add timings for
243 * PIO5.
244 */
245
246static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev)
247{
248 struct ata_device *pair = ata_dev_pair(adev);
249 struct ata_timing t;
250 unsigned long T = 1000000000 / 33333; /* PCI clock based */
251
252 ata_timing_compute(adev, adev->pio_mode, &t, T, 1);
253 if (pair) {
254 struct ata_timing p;
255 ata_timing_compute(pair, pair->pio_mode, &p, T, 1);
256 ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
257 if (pair->dma_mode) {
258 ata_timing_compute(pair, pair->dma_mode, &p, T, 1);
259 ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
260 }
261 }
262
263 /* PIO FIFO is only permitted on ATA disk */
264 if (adev->class != ATA_DEV_ATA)
265 ali_fifo_control(ap, adev, 0x00);
266 ali_program_modes(ap, adev, &t, 0);
267 if (adev->class == ATA_DEV_ATA)
268 ali_fifo_control(ap, adev, 0x05);
269
270}
271
272/**
273 * ali_set_dmamode - set initial DMA mode data
274 * @ap: ATA interface
275 * @adev: ATA device
276 *
277 * FIXME: MWDMA timings
278 */
279
280static void ali_set_dmamode(struct ata_port *ap, struct ata_device *adev)
281{
282 static u8 udma_timing[7] = { 0xC, 0xB, 0xA, 0x9, 0x8, 0xF, 0xD };
283 struct ata_device *pair = ata_dev_pair(adev);
284 struct ata_timing t;
285 unsigned long T = 1000000000 / 33333; /* PCI clock based */
286 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
287
288
289 if (adev->class == ATA_DEV_ATA)
290 ali_fifo_control(ap, adev, 0x08);
291
292 if (adev->dma_mode >= XFER_UDMA_0) {
293 ali_program_modes(ap, adev, NULL, udma_timing[adev->dma_mode - XFER_UDMA_0]);
294 if (adev->dma_mode >= XFER_UDMA_3) {
295 u8 reg4b;
296 pci_read_config_byte(pdev, 0x4B, &reg4b);
297 reg4b |= 1;
298 pci_write_config_byte(pdev, 0x4B, reg4b);
299 }
300 } else {
301 ata_timing_compute(adev, adev->dma_mode, &t, T, 1);
302 if (pair) {
303 struct ata_timing p;
304 ata_timing_compute(pair, pair->pio_mode, &p, T, 1);
305 ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
306 if (pair->dma_mode) {
307 ata_timing_compute(pair, pair->dma_mode, &p, T, 1);
308 ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
309 }
310 }
311 ali_program_modes(ap, adev, &t, 0);
312 }
313}
314
315/**
316 * ali_lock_sectors - Keep older devices to 255 sector mode
317 * @ap: ATA port
318 * @adev: Device
319 *
320 * Called during the bus probe for each device that is found. We use
321 * this call to lock the sector count of the device to 255 or less on
322 * older ALi controllers. If we didn't do this then large I/O's would
323 * require LBA48 commands which the older ALi requires are issued by
324 * slower PIO methods
325 */
326
327static void ali_lock_sectors(struct ata_port *ap, struct ata_device *adev)
328{
329 adev->max_sectors = 255;
330}
331
332static struct scsi_host_template ali_sht = {
333 .module = THIS_MODULE,
334 .name = DRV_NAME,
335 .ioctl = ata_scsi_ioctl,
336 .queuecommand = ata_scsi_queuecmd,
337 .can_queue = ATA_DEF_QUEUE,
338 .this_id = ATA_SHT_THIS_ID,
339 .sg_tablesize = LIBATA_MAX_PRD,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400340 .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
341 .emulated = ATA_SHT_EMULATED,
342 .use_clustering = ATA_SHT_USE_CLUSTERING,
343 .proc_name = DRV_NAME,
344 .dma_boundary = ATA_DMA_BOUNDARY,
345 .slave_configure = ata_scsi_slave_config,
Tejun Heoafdfe892006-11-29 11:26:47 +0900346 .slave_destroy = ata_scsi_slave_destroy,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400347 .bios_param = ata_std_bios_param,
Alan34d8dfb2006-11-22 17:26:06 +0000348 .resume = ata_scsi_device_resume,
349 .suspend = ata_scsi_device_suspend,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400350};
351
352/*
353 * Port operations for PIO only ALi
354 */
355
356static struct ata_port_operations ali_early_port_ops = {
357 .port_disable = ata_port_disable,
358 .set_piomode = ali_set_piomode,
359 .tf_load = ata_tf_load,
360 .tf_read = ata_tf_read,
361 .check_status = ata_check_status,
362 .exec_command = ata_exec_command,
363 .dev_select = ata_std_dev_select,
364
365 .freeze = ata_bmdma_freeze,
366 .thaw = ata_bmdma_thaw,
367 .error_handler = ali_early_error_handler,
368 .post_internal_cmd = ata_bmdma_post_internal_cmd,
369
370 .qc_prep = ata_qc_prep,
371 .qc_issue = ata_qc_issue_prot,
Jeff Garzikbda30282006-09-27 05:41:13 -0400372
Jeff Garzik669a5db2006-08-29 18:12:40 -0400373 .data_xfer = ata_pio_data_xfer,
374
375 .irq_handler = ata_interrupt,
376 .irq_clear = ata_bmdma_irq_clear,
377
378 .port_start = ata_port_start,
379 .port_stop = ata_port_stop,
380 .host_stop = ata_host_stop
381};
382
383/*
384 * Port operations for DMA capable ALi without cable
385 * detect
386 */
387static struct ata_port_operations ali_20_port_ops = {
388 .port_disable = ata_port_disable,
389
390 .set_piomode = ali_set_piomode,
391 .set_dmamode = ali_set_dmamode,
392 .mode_filter = ali_20_filter,
393
394 .tf_load = ata_tf_load,
395 .tf_read = ata_tf_read,
396 .check_status = ata_check_status,
397 .exec_command = ata_exec_command,
398 .dev_select = ata_std_dev_select,
399 .dev_config = ali_lock_sectors,
400
401 .freeze = ata_bmdma_freeze,
402 .thaw = ata_bmdma_thaw,
403 .error_handler = ali_early_error_handler,
404 .post_internal_cmd = ata_bmdma_post_internal_cmd,
405
406 .bmdma_setup = ata_bmdma_setup,
407 .bmdma_start = ata_bmdma_start,
408 .bmdma_stop = ata_bmdma_stop,
409 .bmdma_status = ata_bmdma_status,
410
411 .qc_prep = ata_qc_prep,
412 .qc_issue = ata_qc_issue_prot,
Jeff Garzikbda30282006-09-27 05:41:13 -0400413
Jeff Garzik669a5db2006-08-29 18:12:40 -0400414 .data_xfer = ata_pio_data_xfer,
415
416 .irq_handler = ata_interrupt,
417 .irq_clear = ata_bmdma_irq_clear,
418
419 .port_start = ata_port_start,
420 .port_stop = ata_port_stop,
421 .host_stop = ata_host_stop
422};
423
424/*
425 * Port operations for DMA capable ALi with cable detect
426 */
427static struct ata_port_operations ali_c2_port_ops = {
428 .port_disable = ata_port_disable,
429 .set_piomode = ali_set_piomode,
430 .set_dmamode = ali_set_dmamode,
431 .mode_filter = ata_pci_default_filter,
432 .tf_load = ata_tf_load,
433 .tf_read = ata_tf_read,
434 .check_status = ata_check_status,
435 .exec_command = ata_exec_command,
436 .dev_select = ata_std_dev_select,
437 .dev_config = ali_lock_sectors,
438
439 .freeze = ata_bmdma_freeze,
440 .thaw = ata_bmdma_thaw,
441 .error_handler = ali_c2_error_handler,
442 .post_internal_cmd = ata_bmdma_post_internal_cmd,
443
444 .bmdma_setup = ata_bmdma_setup,
445 .bmdma_start = ata_bmdma_start,
446 .bmdma_stop = ata_bmdma_stop,
447 .bmdma_status = ata_bmdma_status,
448
449 .qc_prep = ata_qc_prep,
450 .qc_issue = ata_qc_issue_prot,
Jeff Garzikbda30282006-09-27 05:41:13 -0400451
Jeff Garzik669a5db2006-08-29 18:12:40 -0400452 .data_xfer = ata_pio_data_xfer,
453
454 .irq_handler = ata_interrupt,
455 .irq_clear = ata_bmdma_irq_clear,
456
457 .port_start = ata_port_start,
458 .port_stop = ata_port_stop,
459 .host_stop = ata_host_stop
460};
461
462/*
463 * Port operations for DMA capable ALi with cable detect and LBA48
464 */
465static struct ata_port_operations ali_c5_port_ops = {
466 .port_disable = ata_port_disable,
467 .set_piomode = ali_set_piomode,
468 .set_dmamode = ali_set_dmamode,
469 .mode_filter = ata_pci_default_filter,
470 .tf_load = ata_tf_load,
471 .tf_read = ata_tf_read,
472 .check_status = ata_check_status,
473 .exec_command = ata_exec_command,
474 .dev_select = ata_std_dev_select,
475
476 .freeze = ata_bmdma_freeze,
477 .thaw = ata_bmdma_thaw,
478 .error_handler = ali_c2_error_handler,
479 .post_internal_cmd = ata_bmdma_post_internal_cmd,
480
481 .bmdma_setup = ata_bmdma_setup,
482 .bmdma_start = ata_bmdma_start,
483 .bmdma_stop = ata_bmdma_stop,
484 .bmdma_status = ata_bmdma_status,
485
486 .qc_prep = ata_qc_prep,
487 .qc_issue = ata_qc_issue_prot,
Jeff Garzikbda30282006-09-27 05:41:13 -0400488
Jeff Garzik669a5db2006-08-29 18:12:40 -0400489 .data_xfer = ata_pio_data_xfer,
490
491 .irq_handler = ata_interrupt,
492 .irq_clear = ata_bmdma_irq_clear,
493
494 .port_start = ata_port_start,
495 .port_stop = ata_port_stop,
496 .host_stop = ata_host_stop
497};
498
Alan34d8dfb2006-11-22 17:26:06 +0000499
500/**
501 * ali_init_chipset - chip setup function
502 * @pdev: PCI device of ATA controller
503 *
504 * Perform the setup on the device that must be done both at boot
505 * and at resume time.
506 */
Jeff Garzikf20b16f2006-12-11 11:14:06 -0500507
Alan34d8dfb2006-11-22 17:26:06 +0000508static void ali_init_chipset(struct pci_dev *pdev)
509{
510 u8 rev, tmp;
511 struct pci_dev *north, *isa_bridge;
512
513 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
514
515 /*
516 * The chipset revision selects the driver operations and
517 * mode data.
518 */
519
520 if (rev >= 0x20 && rev < 0xC2) {
521 /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
522 pci_read_config_byte(pdev, 0x4B, &tmp);
523 /* Clear CD-ROM DMA write bit */
524 tmp &= 0x7F;
525 pci_write_config_byte(pdev, 0x4B, tmp);
526 } else if (rev >= 0xC2) {
527 /* Enable cable detection logic */
528 pci_read_config_byte(pdev, 0x4B, &tmp);
529 pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
530 }
Alan8e42a5a2006-12-04 16:36:05 +0000531 north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0));
Alan34d8dfb2006-11-22 17:26:06 +0000532 isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
533
534 if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
535 /* Configure the ALi bridge logic. For non ALi rely on BIOS.
536 Set the south bridge enable bit */
537 pci_read_config_byte(isa_bridge, 0x79, &tmp);
538 if (rev == 0xC2)
539 pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
Alan8e42a5a2006-12-04 16:36:05 +0000540 else if (rev > 0xC2 && rev < 0xC5)
Alan34d8dfb2006-11-22 17:26:06 +0000541 pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
542 }
543 if (rev >= 0x20) {
544 /*
545 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
546 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
547 * via 0x54/55.
548 */
549 pci_read_config_byte(pdev, 0x53, &tmp);
550 if (rev <= 0x20)
551 tmp &= ~0x02;
552 if (rev >= 0xc7)
553 tmp |= 0x03;
554 else
555 tmp |= 0x01; /* CD_ROM enable for DMA */
556 pci_write_config_byte(pdev, 0x53, tmp);
557 }
558 pci_dev_put(isa_bridge);
559 pci_dev_put(north);
560 ata_pci_clear_simplex(pdev);
561}
Jeff Garzik669a5db2006-08-29 18:12:40 -0400562/**
563 * ali_init_one - discovery callback
564 * @pdev: PCI device ID
565 * @id: PCI table info
566 *
567 * An ALi IDE interface has been discovered. Figure out what revision
568 * and perform configuration work before handing it to the ATA layer
569 */
570
571static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
572{
573 static struct ata_port_info info_early = {
574 .sht = &ali_sht,
575 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
576 .pio_mask = 0x1f,
577 .port_ops = &ali_early_port_ops
578 };
579 /* Revision 0x20 added DMA */
580 static struct ata_port_info info_20 = {
581 .sht = &ali_sht,
582 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
583 .pio_mask = 0x1f,
584 .mwdma_mask = 0x07,
585 .port_ops = &ali_20_port_ops
586 };
587 /* Revision 0x20 with support logic added UDMA */
588 static struct ata_port_info info_20_udma = {
589 .sht = &ali_sht,
590 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
591 .pio_mask = 0x1f,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400592 .mwdma_mask = 0x07,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400593 .udma_mask = 0x07, /* UDMA33 */
594 .port_ops = &ali_20_port_ops
595 };
596 /* Revision 0xC2 adds UDMA66 */
597 static struct ata_port_info info_c2 = {
598 .sht = &ali_sht,
599 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
600 .pio_mask = 0x1f,
601 .mwdma_mask = 0x07,
602 .udma_mask = 0x1f,
603 .port_ops = &ali_c2_port_ops
604 };
605 /* Revision 0xC3 is UDMA100 */
606 static struct ata_port_info info_c3 = {
607 .sht = &ali_sht,
608 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
609 .pio_mask = 0x1f,
610 .mwdma_mask = 0x07,
611 .udma_mask = 0x3f,
612 .port_ops = &ali_c2_port_ops
613 };
614 /* Revision 0xC4 is UDMA133 */
615 static struct ata_port_info info_c4 = {
616 .sht = &ali_sht,
617 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
618 .pio_mask = 0x1f,
619 .mwdma_mask = 0x07,
620 .udma_mask = 0x7f,
621 .port_ops = &ali_c2_port_ops
622 };
623 /* Revision 0xC5 is UDMA133 with LBA48 DMA */
624 static struct ata_port_info info_c5 = {
625 .sht = &ali_sht,
626 .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
627 .pio_mask = 0x1f,
628 .mwdma_mask = 0x07,
629 .udma_mask = 0x7f,
630 .port_ops = &ali_c5_port_ops
631 };
632
633 static struct ata_port_info *port_info[2];
634 u8 rev, tmp;
Alan34d8dfb2006-11-22 17:26:06 +0000635 struct pci_dev *isa_bridge;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400636
637 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
638
639 /*
640 * The chipset revision selects the driver operations and
641 * mode data.
642 */
643
644 if (rev < 0x20) {
645 port_info[0] = port_info[1] = &info_early;
646 } else if (rev < 0xC2) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400647 port_info[0] = port_info[1] = &info_20;
648 } else if (rev == 0xC2) {
649 port_info[0] = port_info[1] = &info_c2;
650 } else if (rev == 0xC3) {
651 port_info[0] = port_info[1] = &info_c3;
652 } else if (rev == 0xC4) {
653 port_info[0] = port_info[1] = &info_c4;
654 } else
655 port_info[0] = port_info[1] = &info_c5;
656
Alan34d8dfb2006-11-22 17:26:06 +0000657 ali_init_chipset(pdev);
Jeff Garzikf20b16f2006-12-11 11:14:06 -0500658
Jeff Garzik669a5db2006-08-29 18:12:40 -0400659 isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
Alan34d8dfb2006-11-22 17:26:06 +0000660 if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
661 /* Are we paired with a UDMA capable chip */
662 pci_read_config_byte(isa_bridge, 0x5E, &tmp);
663 if ((tmp & 0x1E) == 0x12)
664 port_info[0] = port_info[1] = &info_20_udma;
665 pci_dev_put(isa_bridge);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400666 }
Jeff Garzik669a5db2006-08-29 18:12:40 -0400667 return ata_pci_init_one(pdev, port_info, 2);
668}
669
Alan34d8dfb2006-11-22 17:26:06 +0000670static int ali_reinit_one(struct pci_dev *pdev)
671{
672 ali_init_chipset(pdev);
673 return ata_pci_device_resume(pdev);
674}
675
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400676static const struct pci_device_id ali[] = {
677 { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), },
678 { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), },
679
680 { },
Jeff Garzik669a5db2006-08-29 18:12:40 -0400681};
682
683static struct pci_driver ali_pci_driver = {
684 .name = DRV_NAME,
685 .id_table = ali,
686 .probe = ali_init_one,
Alan34d8dfb2006-11-22 17:26:06 +0000687 .remove = ata_pci_remove_one,
688 .suspend = ata_pci_device_suspend,
689 .resume = ali_reinit_one,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400690};
691
692static int __init ali_init(void)
693{
694 return pci_register_driver(&ali_pci_driver);
695}
696
697
698static void __exit ali_exit(void)
699{
700 pci_unregister_driver(&ali_pci_driver);
701}
702
703
704MODULE_AUTHOR("Alan Cox");
705MODULE_DESCRIPTION("low-level driver for ALi PATA");
706MODULE_LICENSE("GPL");
707MODULE_DEVICE_TABLE(pci, ali);
708MODULE_VERSION(DRV_VERSION);
709
710module_init(ali_init);
711module_exit(ali_exit);