blob: a690ca57adb50e349255c321f1d22bbaacd6e40b [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
Uwe Zeisbergerf30c2262006-10-03 23:01:26 +02002 * sound/oss/mpu401.c
Linus Torvalds1da177e2005-04-16 15:20:36 -07003 *
4 * The low level driver for Roland MPU-401 compatible Midi cards.
5 */
6/*
7 * Copyright (C) by Hannu Savolainen 1993-1997
8 *
9 * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL)
10 * Version 2 (June 1991). See the "COPYING" file distributed with this software
11 * for more info.
12 *
13 *
14 * Thomas Sailer ioctl code reworked (vmalloc/vfree removed)
15 * Alan Cox modularisation, use normal request_irq, use dev_id
16 * Bartlomiej Zolnierkiewicz removed some __init to allow using many drivers
17 * Chris Rankin Update the module-usage counter for the coprocessor
18 * Zwane Mwaikambo Changed attach/unload resource freeing
19 */
20
21#include <linux/module.h>
22#include <linux/init.h>
23#include <linux/interrupt.h>
24#include <linux/spinlock.h>
25#define USE_SEQ_MACROS
26#define USE_SIMPLE_MACROS
27
28#include "sound_config.h"
29
30#include "coproc.h"
31#include "mpu401.h"
32
33static int timer_mode = TMR_INTERNAL, timer_caps = TMR_INTERNAL;
34
35struct mpu_config
36{
37 int base; /*
38 * I/O base
39 */
40 int irq;
41 int opened; /*
42 * Open mode
43 */
44 int devno;
45 int synthno;
46 int uart_mode;
47 int initialized;
48 int mode;
49#define MODE_MIDI 1
50#define MODE_SYNTH 2
51 unsigned char version, revision;
52 unsigned int capabilities;
53#define MPU_CAP_INTLG 0x10000000
54#define MPU_CAP_SYNC 0x00000010
55#define MPU_CAP_FSK 0x00000020
56#define MPU_CAP_CLS 0x00000040
57#define MPU_CAP_SMPTE 0x00000080
58#define MPU_CAP_2PORT 0x00000001
59 int timer_flag;
60
61#define MBUF_MAX 10
62#define BUFTEST(dc) if (dc->m_ptr >= MBUF_MAX || dc->m_ptr < 0) \
63 {printk( "MPU: Invalid buffer pointer %d/%d, s=%d\n", dc->m_ptr, dc->m_left, dc->m_state);dc->m_ptr--;}
64 int m_busy;
65 unsigned char m_buf[MBUF_MAX];
66 int m_ptr;
67 int m_state;
68 int m_left;
69 unsigned char last_status;
70 void (*inputintr) (int dev, unsigned char data);
71 int shared_irq;
72 int *osp;
73 spinlock_t lock;
74 };
75
76#define DATAPORT(base) (base)
77#define COMDPORT(base) (base+1)
78#define STATPORT(base) (base+1)
79
80
81static void mpu401_close(int dev);
82
83static inline int mpu401_status(struct mpu_config *devc)
84{
85 return inb(STATPORT(devc->base));
86}
87
88#define input_avail(devc) (!(mpu401_status(devc)&INPUT_AVAIL))
89#define output_ready(devc) (!(mpu401_status(devc)&OUTPUT_READY))
90
91static inline void write_command(struct mpu_config *devc, unsigned char cmd)
92{
93 outb(cmd, COMDPORT(devc->base));
94}
95
96static inline int read_data(struct mpu_config *devc)
97{
98 return inb(DATAPORT(devc->base));
99}
100
101static inline void write_data(struct mpu_config *devc, unsigned char byte)
102{
103 outb(byte, DATAPORT(devc->base));
104}
105
106#define OUTPUT_READY 0x40
107#define INPUT_AVAIL 0x80
108#define MPU_ACK 0xFE
109#define MPU_RESET 0xFF
110#define UART_MODE_ON 0x3F
111
112static struct mpu_config dev_conf[MAX_MIDI_DEV];
113
114static int n_mpu_devs;
115
116static int reset_mpu401(struct mpu_config *devc);
117static void set_uart_mode(int dev, struct mpu_config *devc, int arg);
118
119static int mpu_timer_init(int midi_dev);
120static void mpu_timer_interrupt(void);
121static void timer_ext_event(struct mpu_config *devc, int event, int parm);
122
123static struct synth_info mpu_synth_info_proto = {
124 "MPU-401 MIDI interface",
125 0,
126 SYNTH_TYPE_MIDI,
127 MIDI_TYPE_MPU401,
128 0, 128,
129 0, 128,
130 SYNTH_CAP_INPUT
131};
132
133static struct synth_info mpu_synth_info[MAX_MIDI_DEV];
134
135/*
136 * States for the input scanner
137 */
138
139#define ST_INIT 0 /* Ready for timing byte or msg */
140#define ST_TIMED 1 /* Leading timing byte rcvd */
141#define ST_DATABYTE 2 /* Waiting for (nr_left) data bytes */
142
143#define ST_SYSMSG 100 /* System message (sysx etc). */
144#define ST_SYSEX 101 /* System exclusive msg */
145#define ST_MTC 102 /* Midi Time Code (MTC) qframe msg */
146#define ST_SONGSEL 103 /* Song select */
147#define ST_SONGPOS 104 /* Song position pointer */
148
149static unsigned char len_tab[] = /* # of data bytes following a status
150 */
151{
152 2, /* 8x */
153 2, /* 9x */
154 2, /* Ax */
155 2, /* Bx */
156 1, /* Cx */
157 1, /* Dx */
158 2, /* Ex */
159 0 /* Fx */
160};
161
162#define STORE(cmd) \
163{ \
164 int len; \
165 unsigned char obuf[8]; \
166 cmd; \
167 seq_input_event(obuf, len); \
168}
169
170#define _seqbuf obuf
171#define _seqbufptr 0
172#define _SEQ_ADVBUF(x) len=x
173
174static int mpu_input_scanner(struct mpu_config *devc, unsigned char midic)
175{
176
177 switch (devc->m_state)
178 {
179 case ST_INIT:
180 switch (midic)
181 {
182 case 0xf8:
183 /* Timer overflow */
184 break;
185
186 case 0xfc:
187 printk("<all end>");
188 break;
189
190 case 0xfd:
191 if (devc->timer_flag)
192 mpu_timer_interrupt();
193 break;
194
195 case 0xfe:
196 return MPU_ACK;
197
198 case 0xf0:
199 case 0xf1:
200 case 0xf2:
201 case 0xf3:
202 case 0xf4:
203 case 0xf5:
204 case 0xf6:
205 case 0xf7:
206 printk("<Trk data rq #%d>", midic & 0x0f);
207 break;
208
209 case 0xf9:
210 printk("<conductor rq>");
211 break;
212
213 case 0xff:
214 devc->m_state = ST_SYSMSG;
215 break;
216
217 default:
218 if (midic <= 0xef)
219 {
220 /* printk( "mpu time: %d ", midic); */
221 devc->m_state = ST_TIMED;
222 }
223 else
224 printk("<MPU: Unknown event %02x> ", midic);
225 }
226 break;
227
228 case ST_TIMED:
229 {
230 int msg = ((int) (midic & 0xf0) >> 4);
231
232 devc->m_state = ST_DATABYTE;
233
234 if (msg < 8) /* Data byte */
235 {
236 /* printk( "midi msg (running status) "); */
237 msg = ((int) (devc->last_status & 0xf0) >> 4);
238 msg -= 8;
239 devc->m_left = len_tab[msg] - 1;
240
241 devc->m_ptr = 2;
242 devc->m_buf[0] = devc->last_status;
243 devc->m_buf[1] = midic;
244
245 if (devc->m_left <= 0)
246 {
247 devc->m_state = ST_INIT;
248 do_midi_msg(devc->synthno, devc->m_buf, devc->m_ptr);
249 devc->m_ptr = 0;
250 }
251 }
252 else if (msg == 0xf) /* MPU MARK */
253 {
254 devc->m_state = ST_INIT;
255
256 switch (midic)
257 {
258 case 0xf8:
259 /* printk( "NOP "); */
260 break;
261
262 case 0xf9:
263 /* printk( "meas end "); */
264 break;
265
266 case 0xfc:
267 /* printk( "data end "); */
268 break;
269
270 default:
271 printk("Unknown MPU mark %02x\n", midic);
272 }
273 }
274 else
275 {
276 devc->last_status = midic;
277 /* printk( "midi msg "); */
278 msg -= 8;
279 devc->m_left = len_tab[msg];
280
281 devc->m_ptr = 1;
282 devc->m_buf[0] = midic;
283
284 if (devc->m_left <= 0)
285 {
286 devc->m_state = ST_INIT;
287 do_midi_msg(devc->synthno, devc->m_buf, devc->m_ptr);
288 devc->m_ptr = 0;
289 }
290 }
291 }
292 break;
293
294 case ST_SYSMSG:
295 switch (midic)
296 {
297 case 0xf0:
298 printk("<SYX>");
299 devc->m_state = ST_SYSEX;
300 break;
301
302 case 0xf1:
303 devc->m_state = ST_MTC;
304 break;
305
306 case 0xf2:
307 devc->m_state = ST_SONGPOS;
308 devc->m_ptr = 0;
309 break;
310
311 case 0xf3:
312 devc->m_state = ST_SONGSEL;
313 break;
314
315 case 0xf6:
316 /* printk( "tune_request\n"); */
317 devc->m_state = ST_INIT;
318
319 /*
320 * Real time messages
321 */
322 case 0xf8:
323 /* midi clock */
324 devc->m_state = ST_INIT;
325 timer_ext_event(devc, TMR_CLOCK, 0);
326 break;
327
328 case 0xfA:
329 devc->m_state = ST_INIT;
330 timer_ext_event(devc, TMR_START, 0);
331 break;
332
333 case 0xFB:
334 devc->m_state = ST_INIT;
335 timer_ext_event(devc, TMR_CONTINUE, 0);
336 break;
337
338 case 0xFC:
339 devc->m_state = ST_INIT;
340 timer_ext_event(devc, TMR_STOP, 0);
341 break;
342
343 case 0xFE:
344 /* active sensing */
345 devc->m_state = ST_INIT;
346 break;
347
348 case 0xff:
349 /* printk( "midi hard reset"); */
350 devc->m_state = ST_INIT;
351 break;
352
353 default:
354 printk("unknown MIDI sysmsg %0x\n", midic);
355 devc->m_state = ST_INIT;
356 }
357 break;
358
359 case ST_MTC:
360 devc->m_state = ST_INIT;
361 printk("MTC frame %x02\n", midic);
362 break;
363
364 case ST_SYSEX:
365 if (midic == 0xf7)
366 {
367 printk("<EOX>");
368 devc->m_state = ST_INIT;
369 }
370 else
371 printk("%02x ", midic);
372 break;
373
374 case ST_SONGPOS:
375 BUFTEST(devc);
376 devc->m_buf[devc->m_ptr++] = midic;
377 if (devc->m_ptr == 2)
378 {
379 devc->m_state = ST_INIT;
380 devc->m_ptr = 0;
381 timer_ext_event(devc, TMR_SPP,
382 ((devc->m_buf[1] & 0x7f) << 7) |
383 (devc->m_buf[0] & 0x7f));
384 }
385 break;
386
387 case ST_DATABYTE:
388 BUFTEST(devc);
389 devc->m_buf[devc->m_ptr++] = midic;
390 if ((--devc->m_left) <= 0)
391 {
392 devc->m_state = ST_INIT;
393 do_midi_msg(devc->synthno, devc->m_buf, devc->m_ptr);
394 devc->m_ptr = 0;
395 }
396 break;
397
398 default:
399 printk("Bad state %d ", devc->m_state);
400 devc->m_state = ST_INIT;
401 }
402 return 1;
403}
404
405static void mpu401_input_loop(struct mpu_config *devc)
406{
407 unsigned long flags;
408 int busy;
409 int n;
410
411 spin_lock_irqsave(&devc->lock,flags);
412 busy = devc->m_busy;
413 devc->m_busy = 1;
414 spin_unlock_irqrestore(&devc->lock,flags);
415
416 if (busy) /* Already inside the scanner */
417 return;
418
419 n = 50;
420
421 while (input_avail(devc) && n-- > 0)
422 {
423 unsigned char c = read_data(devc);
424
425 if (devc->mode == MODE_SYNTH)
426 {
427 mpu_input_scanner(devc, c);
428 }
429 else if (devc->opened & OPEN_READ && devc->inputintr != NULL)
430 devc->inputintr(devc->devno, c);
431 }
432 devc->m_busy = 0;
433}
434
David Howells7d12e782006-10-05 14:55:46 +0100435static irqreturn_t mpuintr(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700436{
437 struct mpu_config *devc;
Jeff Garzikc7bec5a2006-10-06 15:00:58 -0400438 int dev = (int)(unsigned long) dev_id;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700439 int handled = 0;
440
441 devc = &dev_conf[dev];
442
443 if (input_avail(devc))
444 {
445 handled = 1;
446 if (devc->base != 0 && (devc->opened & OPEN_READ || devc->mode == MODE_SYNTH))
447 mpu401_input_loop(devc);
448 else
449 {
450 /* Dummy read (just to acknowledge the interrupt) */
451 read_data(devc);
452 }
453 }
454 return IRQ_RETVAL(handled);
455}
456
457static int mpu401_open(int dev, int mode,
458 void (*input) (int dev, unsigned char data),
459 void (*output) (int dev)
460)
461{
462 int err;
463 struct mpu_config *devc;
464 struct coproc_operations *coprocessor;
465
466 if (dev < 0 || dev >= num_midis || midi_devs[dev] == NULL)
467 return -ENXIO;
468
469 devc = &dev_conf[dev];
470
471 if (devc->opened)
472 return -EBUSY;
473 /*
474 * Verify that the device is really running.
475 * Some devices (such as Ensoniq SoundScape don't
476 * work before the on board processor (OBP) is initialized
477 * by downloading its microcode.
478 */
479
480 if (!devc->initialized)
481 {
482 if (mpu401_status(devc) == 0xff) /* Bus float */
483 {
484 printk(KERN_ERR "mpu401: Device not initialized properly\n");
485 return -EIO;
486 }
487 reset_mpu401(devc);
488 }
489
490 if ( (coprocessor = midi_devs[dev]->coproc) != NULL )
491 {
492 if (!try_module_get(coprocessor->owner)) {
493 mpu401_close(dev);
494 return -ENODEV;
495 }
496
497 if ((err = coprocessor->open(coprocessor->devc, COPR_MIDI)) < 0)
498 {
499 printk(KERN_WARNING "MPU-401: Can't access coprocessor device\n");
500 mpu401_close(dev);
501 return err;
502 }
503 }
504
505 set_uart_mode(dev, devc, 1);
506 devc->mode = MODE_MIDI;
507 devc->synthno = 0;
508
509 mpu401_input_loop(devc);
510
511 devc->inputintr = input;
512 devc->opened = mode;
513
514 return 0;
515}
516
517static void mpu401_close(int dev)
518{
519 struct mpu_config *devc;
520 struct coproc_operations *coprocessor;
521
522 devc = &dev_conf[dev];
523 if (devc->uart_mode)
524 reset_mpu401(devc); /*
525 * This disables the UART mode
526 */
527 devc->mode = 0;
528 devc->inputintr = NULL;
529
530 coprocessor = midi_devs[dev]->coproc;
531 if (coprocessor) {
532 coprocessor->close(coprocessor->devc, COPR_MIDI);
533 module_put(coprocessor->owner);
534 }
535 devc->opened = 0;
536}
537
538static int mpu401_out(int dev, unsigned char midi_byte)
539{
540 int timeout;
541 unsigned long flags;
542
543 struct mpu_config *devc;
544
545 devc = &dev_conf[dev];
546
547 /*
548 * Sometimes it takes about 30000 loops before the output becomes ready
549 * (After reset). Normally it takes just about 10 loops.
550 */
551
552 for (timeout = 30000; timeout > 0 && !output_ready(devc); timeout--);
553
554 spin_lock_irqsave(&devc->lock,flags);
555 if (!output_ready(devc))
556 {
557 printk(KERN_WARNING "mpu401: Send data timeout\n");
558 spin_unlock_irqrestore(&devc->lock,flags);
559 return 0;
560 }
561 write_data(devc, midi_byte);
562 spin_unlock_irqrestore(&devc->lock,flags);
563 return 1;
564}
565
566static int mpu401_command(int dev, mpu_command_rec * cmd)
567{
568 int i, timeout, ok;
569 int ret = 0;
570 unsigned long flags;
571 struct mpu_config *devc;
572
573 devc = &dev_conf[dev];
574
575 if (devc->uart_mode) /*
576 * Not possible in UART mode
577 */
578 {
579 printk(KERN_WARNING "mpu401: commands not possible in the UART mode\n");
580 return -EINVAL;
581 }
582 /*
583 * Test for input since pending input seems to block the output.
584 */
585 if (input_avail(devc))
586 mpu401_input_loop(devc);
587
588 /*
589 * Sometimes it takes about 50000 loops before the output becomes ready
590 * (After reset). Normally it takes just about 10 loops.
591 */
592
593 timeout = 50000;
594retry:
595 if (timeout-- <= 0)
596 {
597 printk(KERN_WARNING "mpu401: Command (0x%x) timeout\n", (int) cmd->cmd);
598 return -EIO;
599 }
600 spin_lock_irqsave(&devc->lock,flags);
601
602 if (!output_ready(devc))
603 {
604 spin_unlock_irqrestore(&devc->lock,flags);
605 goto retry;
606 }
607 write_command(devc, cmd->cmd);
608
609 ok = 0;
610 for (timeout = 50000; timeout > 0 && !ok; timeout--)
611 {
612 if (input_avail(devc))
613 {
614 if (devc->opened && devc->mode == MODE_SYNTH)
615 {
616 if (mpu_input_scanner(devc, read_data(devc)) == MPU_ACK)
617 ok = 1;
618 }
619 else
620 {
621 /* Device is not currently open. Use simpler method */
622 if (read_data(devc) == MPU_ACK)
623 ok = 1;
624 }
625 }
626 }
627 if (!ok)
628 {
629 spin_unlock_irqrestore(&devc->lock,flags);
630 return -EIO;
631 }
632 if (cmd->nr_args)
633 {
634 for (i = 0; i < cmd->nr_args; i++)
635 {
636 for (timeout = 3000; timeout > 0 && !output_ready(devc); timeout--);
637
638 if (!mpu401_out(dev, cmd->data[i]))
639 {
640 spin_unlock_irqrestore(&devc->lock,flags);
641 printk(KERN_WARNING "mpu401: Command (0x%x), parm send failed.\n", (int) cmd->cmd);
642 return -EIO;
643 }
644 }
645 }
646 ret = 0;
647 cmd->data[0] = 0;
648
649 if (cmd->nr_returns)
650 {
651 for (i = 0; i < cmd->nr_returns; i++)
652 {
653 ok = 0;
654 for (timeout = 5000; timeout > 0 && !ok; timeout--)
655 if (input_avail(devc))
656 {
657 cmd->data[i] = read_data(devc);
658 ok = 1;
659 }
660 if (!ok)
661 {
662 spin_unlock_irqrestore(&devc->lock,flags);
663 return -EIO;
664 }
665 }
666 }
667 spin_unlock_irqrestore(&devc->lock,flags);
668 return ret;
669}
670
671static int mpu_cmd(int dev, int cmd, int data)
672{
673 int ret;
674
675 static mpu_command_rec rec;
676
677 rec.cmd = cmd & 0xff;
678 rec.nr_args = ((cmd & 0xf0) == 0xE0);
679 rec.nr_returns = ((cmd & 0xf0) == 0xA0);
680 rec.data[0] = data & 0xff;
681
682 if ((ret = mpu401_command(dev, &rec)) < 0)
683 return ret;
684 return (unsigned char) rec.data[0];
685}
686
687static int mpu401_prefix_cmd(int dev, unsigned char status)
688{
689 struct mpu_config *devc = &dev_conf[dev];
690
691 if (devc->uart_mode)
692 return 1;
693
694 if (status < 0xf0)
695 {
696 if (mpu_cmd(dev, 0xD0, 0) < 0)
697 return 0;
698 return 1;
699 }
700 switch (status)
701 {
702 case 0xF0:
703 if (mpu_cmd(dev, 0xDF, 0) < 0)
704 return 0;
705 return 1;
706
707 default:
708 return 0;
709 }
710}
711
712static int mpu401_start_read(int dev)
713{
714 return 0;
715}
716
717static int mpu401_end_read(int dev)
718{
719 return 0;
720}
721
722static int mpu401_ioctl(int dev, unsigned cmd, void __user *arg)
723{
724 struct mpu_config *devc;
725 mpu_command_rec rec;
726 int val, ret;
727
728 devc = &dev_conf[dev];
729 switch (cmd)
730 {
731 case SNDCTL_MIDI_MPUMODE:
732 if (!(devc->capabilities & MPU_CAP_INTLG)) { /* No intelligent mode */
733 printk(KERN_WARNING "mpu401: Intelligent mode not supported by the HW\n");
734 return -EINVAL;
735 }
736 if (get_user(val, (int __user *)arg))
737 return -EFAULT;
738 set_uart_mode(dev, devc, !val);
739 return 0;
740
741 case SNDCTL_MIDI_MPUCMD:
742 if (copy_from_user(&rec, arg, sizeof(rec)))
743 return -EFAULT;
744 if ((ret = mpu401_command(dev, &rec)) < 0)
745 return ret;
746 if (copy_to_user(arg, &rec, sizeof(rec)))
747 return -EFAULT;
748 return 0;
749
750 default:
751 return -EINVAL;
752 }
753}
754
755static void mpu401_kick(int dev)
756{
757}
758
759static int mpu401_buffer_status(int dev)
760{
761 return 0; /*
762 * No data in buffers
763 */
764}
765
766static int mpu_synth_ioctl(int dev, unsigned int cmd, void __user *arg)
767{
768 int midi_dev;
769 struct mpu_config *devc;
770
771 midi_dev = synth_devs[dev]->midi_dev;
772
773 if (midi_dev < 0 || midi_dev > num_midis || midi_devs[midi_dev] == NULL)
774 return -ENXIO;
775
776 devc = &dev_conf[midi_dev];
777
778 switch (cmd)
779 {
780
781 case SNDCTL_SYNTH_INFO:
782 if (copy_to_user(arg, &mpu_synth_info[midi_dev],
783 sizeof(struct synth_info)))
784 return -EFAULT;
785 return 0;
786
787 case SNDCTL_SYNTH_MEMAVL:
788 return 0x7fffffff;
789
790 default:
791 return -EINVAL;
792 }
793}
794
795static int mpu_synth_open(int dev, int mode)
796{
797 int midi_dev, err;
798 struct mpu_config *devc;
799 struct coproc_operations *coprocessor;
800
801 midi_dev = synth_devs[dev]->midi_dev;
802
803 if (midi_dev < 0 || midi_dev > num_midis || midi_devs[midi_dev] == NULL)
804 return -ENXIO;
805
806 devc = &dev_conf[midi_dev];
807
808 /*
809 * Verify that the device is really running.
810 * Some devices (such as Ensoniq SoundScape don't
811 * work before the on board processor (OBP) is initialized
812 * by downloading its microcode.
813 */
814
815 if (!devc->initialized)
816 {
817 if (mpu401_status(devc) == 0xff) /* Bus float */
818 {
819 printk(KERN_ERR "mpu401: Device not initialized properly\n");
820 return -EIO;
821 }
822 reset_mpu401(devc);
823 }
824 if (devc->opened)
825 return -EBUSY;
826 devc->mode = MODE_SYNTH;
827 devc->synthno = dev;
828
829 devc->inputintr = NULL;
830
831 coprocessor = midi_devs[midi_dev]->coproc;
832 if (coprocessor) {
833 if (!try_module_get(coprocessor->owner))
834 return -ENODEV;
835
836 if ((err = coprocessor->open(coprocessor->devc, COPR_MIDI)) < 0)
837 {
838 printk(KERN_WARNING "mpu401: Can't access coprocessor device\n");
839 return err;
840 }
841 }
842 devc->opened = mode;
843 reset_mpu401(devc);
844
845 if (mode & OPEN_READ)
846 {
847 mpu_cmd(midi_dev, 0x8B, 0); /* Enable data in stop mode */
848 mpu_cmd(midi_dev, 0x34, 0); /* Return timing bytes in stop mode */
849 mpu_cmd(midi_dev, 0x87, 0); /* Enable pitch & controller */
850 }
851 return 0;
852}
853
854static void mpu_synth_close(int dev)
855{
856 int midi_dev;
857 struct mpu_config *devc;
858 struct coproc_operations *coprocessor;
859
860 midi_dev = synth_devs[dev]->midi_dev;
861
862 devc = &dev_conf[midi_dev];
863 mpu_cmd(midi_dev, 0x15, 0); /* Stop recording, playback and MIDI */
864 mpu_cmd(midi_dev, 0x8a, 0); /* Disable data in stopped mode */
865
866 devc->inputintr = NULL;
867
868 coprocessor = midi_devs[midi_dev]->coproc;
869 if (coprocessor) {
870 coprocessor->close(coprocessor->devc, COPR_MIDI);
871 module_put(coprocessor->owner);
872 }
873 devc->opened = 0;
874 devc->mode = 0;
875}
876
877#define MIDI_SYNTH_NAME "MPU-401 UART Midi"
878#define MIDI_SYNTH_CAPS SYNTH_CAP_INPUT
879#include "midi_synth.h"
880
881static struct synth_operations mpu401_synth_proto =
882{
883 .owner = THIS_MODULE,
884 .id = "MPU401",
885 .info = NULL,
886 .midi_dev = 0,
887 .synth_type = SYNTH_TYPE_MIDI,
888 .synth_subtype = 0,
889 .open = mpu_synth_open,
890 .close = mpu_synth_close,
891 .ioctl = mpu_synth_ioctl,
892 .kill_note = midi_synth_kill_note,
893 .start_note = midi_synth_start_note,
894 .set_instr = midi_synth_set_instr,
895 .reset = midi_synth_reset,
896 .hw_control = midi_synth_hw_control,
897 .load_patch = midi_synth_load_patch,
898 .aftertouch = midi_synth_aftertouch,
899 .controller = midi_synth_controller,
900 .panning = midi_synth_panning,
901 .bender = midi_synth_bender,
902 .setup_voice = midi_synth_setup_voice,
903 .send_sysex = midi_synth_send_sysex
904};
905
906static struct synth_operations *mpu401_synth_operations[MAX_MIDI_DEV];
907
908static struct midi_operations mpu401_midi_proto =
909{
910 .owner = THIS_MODULE,
911 .info = {"MPU-401 Midi", 0, MIDI_CAP_MPU401, SNDCARD_MPU401},
912 .in_info = {0},
913 .open = mpu401_open,
914 .close = mpu401_close,
915 .ioctl = mpu401_ioctl,
916 .outputc = mpu401_out,
917 .start_read = mpu401_start_read,
918 .end_read = mpu401_end_read,
919 .kick = mpu401_kick,
920 .buffer_status = mpu401_buffer_status,
921 .prefix_cmd = mpu401_prefix_cmd
922};
923
924static struct midi_operations mpu401_midi_operations[MAX_MIDI_DEV];
925
926static void mpu401_chk_version(int n, struct mpu_config *devc)
927{
928 int tmp;
929 unsigned long flags;
930
931 devc->version = devc->revision = 0;
932
933 spin_lock_irqsave(&devc->lock,flags);
934 if ((tmp = mpu_cmd(n, 0xAC, 0)) < 0)
935 {
936 spin_unlock_irqrestore(&devc->lock,flags);
937 return;
938 }
939 if ((tmp & 0xf0) > 0x20) /* Why it's larger than 2.x ??? */
940 {
941 spin_unlock_irqrestore(&devc->lock,flags);
942 return;
943 }
944 devc->version = tmp;
945
946 if ((tmp = mpu_cmd(n, 0xAD, 0)) < 0)
947 {
948 devc->version = 0;
949 spin_unlock_irqrestore(&devc->lock,flags);
950 return;
951 }
952 devc->revision = tmp;
953 spin_unlock_irqrestore(&devc->lock,flags);
954}
955
956int attach_mpu401(struct address_info *hw_config, struct module *owner)
957{
958 unsigned long flags;
959 char revision_char;
960
961 int m, ret;
962 struct mpu_config *devc;
963
964 hw_config->slots[1] = -1;
965 m = sound_alloc_mididev();
966 if (m == -1)
967 {
968 printk(KERN_WARNING "MPU-401: Too many midi devices detected\n");
969 ret = -ENOMEM;
970 goto out_err;
971 }
972 devc = &dev_conf[m];
973 devc->base = hw_config->io_base;
974 devc->osp = hw_config->osp;
975 devc->irq = hw_config->irq;
976 devc->opened = 0;
977 devc->uart_mode = 0;
978 devc->initialized = 0;
979 devc->version = 0;
980 devc->revision = 0;
981 devc->capabilities = 0;
982 devc->timer_flag = 0;
983 devc->m_busy = 0;
984 devc->m_state = ST_INIT;
985 devc->shared_irq = hw_config->always_detect;
986 devc->irq = hw_config->irq;
987 spin_lock_init(&devc->lock);
988
989 if (devc->irq < 0)
990 {
991 devc->irq *= -1;
992 devc->shared_irq = 1;
993 }
994
995 if (!hw_config->always_detect)
996 {
997 /* Verify the hardware again */
998 if (!reset_mpu401(devc))
999 {
1000 printk(KERN_WARNING "mpu401: Device didn't respond\n");
1001 ret = -ENODEV;
1002 goto out_mididev;
1003 }
1004 if (!devc->shared_irq)
1005 {
Andrew Morton69378382007-07-15 23:40:04 -07001006 if (request_irq(devc->irq, mpuintr, 0, "mpu401",
1007 hw_config) < 0)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001008 {
1009 printk(KERN_WARNING "mpu401: Failed to allocate IRQ%d\n", devc->irq);
1010 ret = -ENOMEM;
1011 goto out_mididev;
1012 }
1013 }
1014 spin_lock_irqsave(&devc->lock,flags);
1015 mpu401_chk_version(m, devc);
1016 if (devc->version == 0)
1017 mpu401_chk_version(m, devc);
1018 spin_unlock_irqrestore(&devc->lock,flags);
1019 }
1020
1021 if (devc->version != 0)
1022 if (mpu_cmd(m, 0xC5, 0) >= 0) /* Set timebase OK */
1023 if (mpu_cmd(m, 0xE0, 120) >= 0) /* Set tempo OK */
1024 devc->capabilities |= MPU_CAP_INTLG; /* Supports intelligent mode */
1025
1026
Robert P. J. Day5cbded52006-12-13 00:35:56 -08001027 mpu401_synth_operations[m] = kmalloc(sizeof(struct synth_operations), GFP_KERNEL);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001028
1029 if (mpu401_synth_operations[m] == NULL)
1030 {
1031 printk(KERN_ERR "mpu401: Can't allocate memory\n");
1032 ret = -ENOMEM;
1033 goto out_irq;
1034 }
1035 if (!(devc->capabilities & MPU_CAP_INTLG)) /* No intelligent mode */
1036 {
1037 memcpy((char *) mpu401_synth_operations[m],
1038 (char *) &std_midi_synth,
1039 sizeof(struct synth_operations));
1040 }
1041 else
1042 {
1043 memcpy((char *) mpu401_synth_operations[m],
1044 (char *) &mpu401_synth_proto,
1045 sizeof(struct synth_operations));
1046 }
1047 if (owner)
1048 mpu401_synth_operations[m]->owner = owner;
1049
1050 memcpy((char *) &mpu401_midi_operations[m],
1051 (char *) &mpu401_midi_proto,
1052 sizeof(struct midi_operations));
1053
1054 mpu401_midi_operations[m].converter = mpu401_synth_operations[m];
1055
1056 memcpy((char *) &mpu_synth_info[m],
1057 (char *) &mpu_synth_info_proto,
1058 sizeof(struct synth_info));
1059
1060 n_mpu_devs++;
1061
1062 if (devc->version == 0x20 && devc->revision >= 0x07) /* MusicQuest interface */
1063 {
1064 int ports = (devc->revision & 0x08) ? 32 : 16;
1065
1066 devc->capabilities |= MPU_CAP_SYNC | MPU_CAP_SMPTE |
1067 MPU_CAP_CLS | MPU_CAP_2PORT;
1068
1069 revision_char = (devc->revision == 0x7f) ? 'M' : ' ';
1070 sprintf(mpu_synth_info[m].name, "MQX-%d%c MIDI Interface #%d",
1071 ports,
1072 revision_char,
1073 n_mpu_devs);
1074 }
1075 else
1076 {
1077 revision_char = devc->revision ? devc->revision + '@' : ' ';
1078 if ((int) devc->revision > ('Z' - '@'))
1079 revision_char = '+';
1080
1081 devc->capabilities |= MPU_CAP_SYNC | MPU_CAP_FSK;
1082
1083 if (hw_config->name)
1084 sprintf(mpu_synth_info[m].name, "%s (MPU401)", hw_config->name);
1085 else
1086 sprintf(mpu_synth_info[m].name,
1087 "MPU-401 %d.%d%c Midi interface #%d",
1088 (int) (devc->version & 0xf0) >> 4,
1089 devc->version & 0x0f,
1090 revision_char,
1091 n_mpu_devs);
1092 }
1093
1094 strcpy(mpu401_midi_operations[m].info.name,
1095 mpu_synth_info[m].name);
1096
1097 conf_printf(mpu_synth_info[m].name, hw_config);
1098
1099 mpu401_synth_operations[m]->midi_dev = devc->devno = m;
1100 mpu401_synth_operations[devc->devno]->info = &mpu_synth_info[devc->devno];
1101
1102 if (devc->capabilities & MPU_CAP_INTLG) /* Intelligent mode */
1103 hw_config->slots[2] = mpu_timer_init(m);
1104
1105 midi_devs[m] = &mpu401_midi_operations[devc->devno];
1106
1107 if (owner)
1108 midi_devs[m]->owner = owner;
1109
1110 hw_config->slots[1] = m;
1111 sequencer_init();
1112
1113 return 0;
1114
1115out_irq:
Andrew Morton69378382007-07-15 23:40:04 -07001116 free_irq(devc->irq, hw_config);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001117out_mididev:
1118 sound_unload_mididev(m);
1119out_err:
1120 release_region(hw_config->io_base, 2);
1121 return ret;
1122}
1123
1124static int reset_mpu401(struct mpu_config *devc)
1125{
1126 unsigned long flags;
1127 int ok, timeout, n;
1128 int timeout_limit;
1129
1130 /*
1131 * Send the RESET command. Try again if no success at the first time.
1132 * (If the device is in the UART mode, it will not ack the reset cmd).
1133 */
1134
1135 ok = 0;
1136
1137 timeout_limit = devc->initialized ? 30000 : 100000;
1138 devc->initialized = 1;
1139
1140 for (n = 0; n < 2 && !ok; n++)
1141 {
1142 for (timeout = timeout_limit; timeout > 0 && !ok; timeout--)
1143 ok = output_ready(devc);
1144
1145 write_command(devc, MPU_RESET); /*
1146 * Send MPU-401 RESET Command
1147 */
1148
1149 /*
1150 * Wait at least 25 msec. This method is not accurate so let's make the
1151 * loop bit longer. Cannot sleep since this is called during boot.
1152 */
1153
1154 for (timeout = timeout_limit * 2; timeout > 0 && !ok; timeout--)
1155 {
1156 spin_lock_irqsave(&devc->lock,flags);
1157 if (input_avail(devc))
1158 if (read_data(devc) == MPU_ACK)
1159 ok = 1;
1160 spin_unlock_irqrestore(&devc->lock,flags);
1161 }
1162
1163 }
1164
1165 devc->m_state = ST_INIT;
1166 devc->m_ptr = 0;
1167 devc->m_left = 0;
1168 devc->last_status = 0;
1169 devc->uart_mode = 0;
1170
1171 return ok;
1172}
1173
1174static void set_uart_mode(int dev, struct mpu_config *devc, int arg)
1175{
1176 if (!arg && (devc->capabilities & MPU_CAP_INTLG))
1177 return;
1178 if ((devc->uart_mode == 0) == (arg == 0))
1179 return; /* Already set */
1180 reset_mpu401(devc); /* This exits the uart mode */
1181
1182 if (arg)
1183 {
1184 if (mpu_cmd(dev, UART_MODE_ON, 0) < 0)
1185 {
1186 printk(KERN_ERR "mpu401: Can't enter UART mode\n");
1187 devc->uart_mode = 0;
1188 return;
1189 }
1190 }
1191 devc->uart_mode = arg;
1192
1193}
1194
1195int probe_mpu401(struct address_info *hw_config, struct resource *ports)
1196{
1197 int ok = 0;
1198 struct mpu_config tmp_devc;
1199
1200 tmp_devc.base = hw_config->io_base;
1201 tmp_devc.irq = hw_config->irq;
1202 tmp_devc.initialized = 0;
1203 tmp_devc.opened = 0;
1204 tmp_devc.osp = hw_config->osp;
1205
1206 if (hw_config->always_detect)
1207 return 1;
1208
1209 if (inb(hw_config->io_base + 1) == 0xff)
1210 {
1211 DDB(printk("MPU401: Port %x looks dead.\n", hw_config->io_base));
1212 return 0; /* Just bus float? */
1213 }
1214 ok = reset_mpu401(&tmp_devc);
1215
1216 if (!ok)
1217 {
1218 DDB(printk("MPU401: Reset failed on port %x\n", hw_config->io_base));
1219 }
1220 return ok;
1221}
1222
1223void unload_mpu401(struct address_info *hw_config)
1224{
1225 void *p;
1226 int n=hw_config->slots[1];
1227
1228 if (n != -1) {
1229 release_region(hw_config->io_base, 2);
1230 if (hw_config->always_detect == 0 && hw_config->irq > 0)
Andrew Morton69378382007-07-15 23:40:04 -07001231 free_irq(hw_config->irq, hw_config);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001232 p=mpu401_synth_operations[n];
1233 sound_unload_mididev(n);
1234 sound_unload_timerdev(hw_config->slots[2]);
Jesper Juhl09417372005-06-25 14:58:49 -07001235 kfree(p);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001236 }
1237}
1238
1239/*****************************************************
1240 * Timer stuff
1241 ****************************************************/
1242
1243static volatile int timer_initialized = 0, timer_open = 0, tmr_running = 0;
1244static volatile int curr_tempo, curr_timebase, hw_timebase;
1245static int max_timebase = 8; /* 8*24=192 ppqn */
1246static volatile unsigned long next_event_time;
1247static volatile unsigned long curr_ticks, curr_clocks;
1248static unsigned long prev_event_time;
1249static int metronome_mode;
1250
1251static unsigned long clocks2ticks(unsigned long clocks)
1252{
1253 /*
1254 * The MPU-401 supports just a limited set of possible timebase values.
1255 * Since the applications require more choices, the driver has to
1256 * program the HW to do its best and to convert between the HW and
1257 * actual timebases.
1258 */
1259 return ((clocks * curr_timebase) + (hw_timebase / 2)) / hw_timebase;
1260}
1261
1262static void set_timebase(int midi_dev, int val)
1263{
1264 int hw_val;
1265
1266 if (val < 48)
1267 val = 48;
1268 if (val > 1000)
1269 val = 1000;
1270
1271 hw_val = val;
1272 hw_val = (hw_val + 12) / 24;
1273 if (hw_val > max_timebase)
1274 hw_val = max_timebase;
1275
1276 if (mpu_cmd(midi_dev, 0xC0 | (hw_val & 0x0f), 0) < 0)
1277 {
1278 printk(KERN_WARNING "mpu401: Can't set HW timebase to %d\n", hw_val * 24);
1279 return;
1280 }
1281 hw_timebase = hw_val * 24;
1282 curr_timebase = val;
1283
1284}
1285
1286static void tmr_reset(struct mpu_config *devc)
1287{
1288 unsigned long flags;
1289
1290 spin_lock_irqsave(&devc->lock,flags);
1291 next_event_time = (unsigned long) -1;
1292 prev_event_time = 0;
1293 curr_ticks = curr_clocks = 0;
1294 spin_unlock_irqrestore(&devc->lock,flags);
1295}
1296
1297static void set_timer_mode(int midi_dev)
1298{
1299 if (timer_mode & TMR_MODE_CLS)
1300 mpu_cmd(midi_dev, 0x3c, 0); /* Use CLS sync */
1301 else if (timer_mode & TMR_MODE_SMPTE)
1302 mpu_cmd(midi_dev, 0x3d, 0); /* Use SMPTE sync */
1303
1304 if (timer_mode & TMR_INTERNAL)
1305 {
1306 mpu_cmd(midi_dev, 0x80, 0); /* Use MIDI sync */
1307 }
1308 else
1309 {
1310 if (timer_mode & (TMR_MODE_MIDI | TMR_MODE_CLS))
1311 {
1312 mpu_cmd(midi_dev, 0x82, 0); /* Use MIDI sync */
1313 mpu_cmd(midi_dev, 0x91, 0); /* Enable ext MIDI ctrl */
1314 }
1315 else if (timer_mode & TMR_MODE_FSK)
1316 mpu_cmd(midi_dev, 0x81, 0); /* Use FSK sync */
1317 }
1318}
1319
1320static void stop_metronome(int midi_dev)
1321{
1322 mpu_cmd(midi_dev, 0x84, 0); /* Disable metronome */
1323}
1324
1325static void setup_metronome(int midi_dev)
1326{
1327 int numerator, denominator;
1328 int clks_per_click, num_32nds_per_beat;
1329 int beats_per_measure;
1330
1331 numerator = ((unsigned) metronome_mode >> 24) & 0xff;
1332 denominator = ((unsigned) metronome_mode >> 16) & 0xff;
1333 clks_per_click = ((unsigned) metronome_mode >> 8) & 0xff;
1334 num_32nds_per_beat = (unsigned) metronome_mode & 0xff;
1335 beats_per_measure = (numerator * 4) >> denominator;
1336
1337 if (!metronome_mode)
1338 mpu_cmd(midi_dev, 0x84, 0); /* Disable metronome */
1339 else
1340 {
1341 mpu_cmd(midi_dev, 0xE4, clks_per_click);
1342 mpu_cmd(midi_dev, 0xE6, beats_per_measure);
1343 mpu_cmd(midi_dev, 0x83, 0); /* Enable metronome without accents */
1344 }
1345}
1346
1347static int mpu_start_timer(int midi_dev)
1348{
1349 struct mpu_config *devc= &dev_conf[midi_dev];
1350
1351 tmr_reset(devc);
1352 set_timer_mode(midi_dev);
1353
1354 if (tmr_running)
1355 return TIMER_NOT_ARMED; /* Already running */
1356
1357 if (timer_mode & TMR_INTERNAL)
1358 {
1359 mpu_cmd(midi_dev, 0x02, 0); /* Send MIDI start */
1360 tmr_running = 1;
1361 return TIMER_NOT_ARMED;
1362 }
1363 else
1364 {
1365 mpu_cmd(midi_dev, 0x35, 0); /* Enable mode messages to PC */
1366 mpu_cmd(midi_dev, 0x38, 0); /* Enable sys common messages to PC */
1367 mpu_cmd(midi_dev, 0x39, 0); /* Enable real time messages to PC */
1368 mpu_cmd(midi_dev, 0x97, 0); /* Enable system exclusive messages to PC */
1369 }
1370 return TIMER_ARMED;
1371}
1372
1373static int mpu_timer_open(int dev, int mode)
1374{
1375 int midi_dev = sound_timer_devs[dev]->devlink;
1376 struct mpu_config *devc= &dev_conf[midi_dev];
1377
1378 if (timer_open)
1379 return -EBUSY;
1380
1381 tmr_reset(devc);
1382 curr_tempo = 50;
1383 mpu_cmd(midi_dev, 0xE0, 50);
1384 curr_timebase = hw_timebase = 120;
1385 set_timebase(midi_dev, 120);
1386 timer_open = 1;
1387 metronome_mode = 0;
1388 set_timer_mode(midi_dev);
1389
1390 mpu_cmd(midi_dev, 0xe7, 0x04); /* Send all clocks to host */
1391 mpu_cmd(midi_dev, 0x95, 0); /* Enable clock to host */
1392
1393 return 0;
1394}
1395
1396static void mpu_timer_close(int dev)
1397{
1398 int midi_dev = sound_timer_devs[dev]->devlink;
1399
1400 timer_open = tmr_running = 0;
1401 mpu_cmd(midi_dev, 0x15, 0); /* Stop all */
1402 mpu_cmd(midi_dev, 0x94, 0); /* Disable clock to host */
1403 mpu_cmd(midi_dev, 0x8c, 0); /* Disable measure end messages to host */
1404 stop_metronome(midi_dev);
1405}
1406
1407static int mpu_timer_event(int dev, unsigned char *event)
1408{
1409 unsigned char command = event[1];
1410 unsigned long parm = *(unsigned int *) &event[4];
1411 int midi_dev = sound_timer_devs[dev]->devlink;
1412
1413 switch (command)
1414 {
1415 case TMR_WAIT_REL:
1416 parm += prev_event_time;
1417 case TMR_WAIT_ABS:
1418 if (parm > 0)
1419 {
1420 long time;
1421
1422 if (parm <= curr_ticks) /* It's the time */
1423 return TIMER_NOT_ARMED;
1424 time = parm;
1425 next_event_time = prev_event_time = time;
1426
1427 return TIMER_ARMED;
1428 }
1429 break;
1430
1431 case TMR_START:
1432 if (tmr_running)
1433 break;
1434 return mpu_start_timer(midi_dev);
1435
1436 case TMR_STOP:
1437 mpu_cmd(midi_dev, 0x01, 0); /* Send MIDI stop */
1438 stop_metronome(midi_dev);
1439 tmr_running = 0;
1440 break;
1441
1442 case TMR_CONTINUE:
1443 if (tmr_running)
1444 break;
1445 mpu_cmd(midi_dev, 0x03, 0); /* Send MIDI continue */
1446 setup_metronome(midi_dev);
1447 tmr_running = 1;
1448 break;
1449
1450 case TMR_TEMPO:
1451 if (parm)
1452 {
1453 if (parm < 8)
1454 parm = 8;
1455 if (parm > 250)
1456 parm = 250;
1457 if (mpu_cmd(midi_dev, 0xE0, parm) < 0)
1458 printk(KERN_WARNING "mpu401: Can't set tempo to %d\n", (int) parm);
1459 curr_tempo = parm;
1460 }
1461 break;
1462
1463 case TMR_ECHO:
1464 seq_copy_to_input(event, 8);
1465 break;
1466
1467 case TMR_TIMESIG:
1468 if (metronome_mode) /* Metronome enabled */
1469 {
1470 metronome_mode = parm;
1471 setup_metronome(midi_dev);
1472 }
1473 break;
1474
1475 default:;
1476 }
1477 return TIMER_NOT_ARMED;
1478}
1479
1480static unsigned long mpu_timer_get_time(int dev)
1481{
1482 if (!timer_open)
1483 return 0;
1484
1485 return curr_ticks;
1486}
1487
1488static int mpu_timer_ioctl(int dev, unsigned int command, void __user *arg)
1489{
1490 int midi_dev = sound_timer_devs[dev]->devlink;
1491 int __user *p = (int __user *)arg;
1492
1493 switch (command)
1494 {
1495 case SNDCTL_TMR_SOURCE:
1496 {
1497 int parm;
1498
1499 if (get_user(parm, p))
1500 return -EFAULT;
1501 parm &= timer_caps;
1502
1503 if (parm != 0)
1504 {
1505 timer_mode = parm;
1506
1507 if (timer_mode & TMR_MODE_CLS)
1508 mpu_cmd(midi_dev, 0x3c, 0); /* Use CLS sync */
1509 else if (timer_mode & TMR_MODE_SMPTE)
1510 mpu_cmd(midi_dev, 0x3d, 0); /* Use SMPTE sync */
1511 }
1512 if (put_user(timer_mode, p))
1513 return -EFAULT;
1514 return timer_mode;
1515 }
1516 break;
1517
1518 case SNDCTL_TMR_START:
1519 mpu_start_timer(midi_dev);
1520 return 0;
1521
1522 case SNDCTL_TMR_STOP:
1523 tmr_running = 0;
1524 mpu_cmd(midi_dev, 0x01, 0); /* Send MIDI stop */
1525 stop_metronome(midi_dev);
1526 return 0;
1527
1528 case SNDCTL_TMR_CONTINUE:
1529 if (tmr_running)
1530 return 0;
1531 tmr_running = 1;
1532 mpu_cmd(midi_dev, 0x03, 0); /* Send MIDI continue */
1533 return 0;
1534
1535 case SNDCTL_TMR_TIMEBASE:
1536 {
1537 int val;
1538 if (get_user(val, p))
1539 return -EFAULT;
1540 if (val)
1541 set_timebase(midi_dev, val);
1542 if (put_user(curr_timebase, p))
1543 return -EFAULT;
1544 return curr_timebase;
1545 }
1546 break;
1547
1548 case SNDCTL_TMR_TEMPO:
1549 {
1550 int val;
1551 int ret;
1552
1553 if (get_user(val, p))
1554 return -EFAULT;
1555
1556 if (val)
1557 {
1558 if (val < 8)
1559 val = 8;
1560 if (val > 250)
1561 val = 250;
1562 if ((ret = mpu_cmd(midi_dev, 0xE0, val)) < 0)
1563 {
1564 printk(KERN_WARNING "mpu401: Can't set tempo to %d\n", (int) val);
1565 return ret;
1566 }
1567 curr_tempo = val;
1568 }
1569 if (put_user(curr_tempo, p))
1570 return -EFAULT;
1571 return curr_tempo;
1572 }
1573 break;
1574
1575 case SNDCTL_SEQ_CTRLRATE:
1576 {
1577 int val;
1578 if (get_user(val, p))
1579 return -EFAULT;
1580
1581 if (val != 0) /* Can't change */
1582 return -EINVAL;
1583 val = ((curr_tempo * curr_timebase) + 30)/60;
1584 if (put_user(val, p))
1585 return -EFAULT;
1586 return val;
1587 }
1588 break;
1589
1590 case SNDCTL_SEQ_GETTIME:
1591 if (put_user(curr_ticks, p))
1592 return -EFAULT;
1593 return curr_ticks;
1594
1595 case SNDCTL_TMR_METRONOME:
1596 if (get_user(metronome_mode, p))
1597 return -EFAULT;
1598 setup_metronome(midi_dev);
1599 return 0;
1600
1601 default:;
1602 }
1603 return -EINVAL;
1604}
1605
1606static void mpu_timer_arm(int dev, long time)
1607{
1608 if (time < 0)
1609 time = curr_ticks + 1;
1610 else if (time <= curr_ticks) /* It's the time */
1611 return;
1612 next_event_time = prev_event_time = time;
1613 return;
1614}
1615
1616static struct sound_timer_operations mpu_timer =
1617{
1618 .owner = THIS_MODULE,
1619 .info = {"MPU-401 Timer", 0},
1620 .priority = 10, /* Priority */
1621 .devlink = 0, /* Local device link */
1622 .open = mpu_timer_open,
1623 .close = mpu_timer_close,
1624 .event = mpu_timer_event,
1625 .get_time = mpu_timer_get_time,
1626 .ioctl = mpu_timer_ioctl,
1627 .arm_timer = mpu_timer_arm
1628};
1629
1630static void mpu_timer_interrupt(void)
1631{
1632 if (!timer_open)
1633 return;
1634
1635 if (!tmr_running)
1636 return;
1637
1638 curr_clocks++;
1639 curr_ticks = clocks2ticks(curr_clocks);
1640
1641 if (curr_ticks >= next_event_time)
1642 {
1643 next_event_time = (unsigned long) -1;
1644 sequencer_timer(0);
1645 }
1646}
1647
1648static void timer_ext_event(struct mpu_config *devc, int event, int parm)
1649{
1650 int midi_dev = devc->devno;
1651
1652 if (!devc->timer_flag)
1653 return;
1654
1655 switch (event)
1656 {
1657 case TMR_CLOCK:
1658 printk("<MIDI clk>");
1659 break;
1660
1661 case TMR_START:
1662 printk("Ext MIDI start\n");
1663 if (!tmr_running)
1664 {
1665 if (timer_mode & TMR_EXTERNAL)
1666 {
1667 tmr_running = 1;
1668 setup_metronome(midi_dev);
1669 next_event_time = 0;
1670 STORE(SEQ_START_TIMER());
1671 }
1672 }
1673 break;
1674
1675 case TMR_STOP:
1676 printk("Ext MIDI stop\n");
1677 if (timer_mode & TMR_EXTERNAL)
1678 {
1679 tmr_running = 0;
1680 stop_metronome(midi_dev);
1681 STORE(SEQ_STOP_TIMER());
1682 }
1683 break;
1684
1685 case TMR_CONTINUE:
1686 printk("Ext MIDI continue\n");
1687 if (timer_mode & TMR_EXTERNAL)
1688 {
1689 tmr_running = 1;
1690 setup_metronome(midi_dev);
1691 STORE(SEQ_CONTINUE_TIMER());
1692 }
1693 break;
1694
1695 case TMR_SPP:
1696 printk("Songpos: %d\n", parm);
1697 if (timer_mode & TMR_EXTERNAL)
1698 {
1699 STORE(SEQ_SONGPOS(parm));
1700 }
1701 break;
1702 }
1703}
1704
1705static int mpu_timer_init(int midi_dev)
1706{
1707 struct mpu_config *devc;
1708 int n;
1709
1710 devc = &dev_conf[midi_dev];
1711
1712 if (timer_initialized)
1713 return -1; /* There is already a similar timer */
1714
1715 timer_initialized = 1;
1716
1717 mpu_timer.devlink = midi_dev;
1718 dev_conf[midi_dev].timer_flag = 1;
1719
1720 n = sound_alloc_timerdev();
1721 if (n == -1)
1722 n = 0;
1723 sound_timer_devs[n] = &mpu_timer;
1724
1725 if (devc->version < 0x20) /* Original MPU-401 */
1726 timer_caps = TMR_INTERNAL | TMR_EXTERNAL | TMR_MODE_FSK | TMR_MODE_MIDI;
1727 else
1728 {
1729 /*
1730 * The version number 2.0 is used (at least) by the
1731 * MusicQuest cards and the Roland Super-MPU.
1732 *
1733 * MusicQuest has given a special meaning to the bits of the
1734 * revision number. The Super-MPU returns 0.
1735 */
1736
1737 if (devc->revision)
1738 timer_caps |= TMR_EXTERNAL | TMR_MODE_MIDI;
1739
1740 if (devc->revision & 0x02)
1741 timer_caps |= TMR_MODE_CLS;
1742
1743
1744 if (devc->revision & 0x40)
1745 max_timebase = 10; /* Has the 216 and 240 ppqn modes */
1746 }
1747
1748 timer_mode = (TMR_INTERNAL | TMR_MODE_MIDI) & timer_caps;
1749 return n;
1750
1751}
1752
1753EXPORT_SYMBOL(probe_mpu401);
1754EXPORT_SYMBOL(attach_mpu401);
1755EXPORT_SYMBOL(unload_mpu401);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001756
1757static struct address_info cfg;
1758
1759static int io = -1;
1760static int irq = -1;
1761
1762module_param(irq, int, 0);
1763module_param(io, int, 0);
1764
1765static int __init init_mpu401(void)
1766{
1767 int ret;
1768 /* Can be loaded either for module use or to provide functions
1769 to others */
1770 if (io != -1 && irq != -1) {
1771 struct resource *ports;
1772 cfg.irq = irq;
1773 cfg.io_base = io;
1774 ports = request_region(io, 2, "mpu401");
1775 if (!ports)
1776 return -EBUSY;
1777 if (probe_mpu401(&cfg, ports) == 0) {
1778 release_region(io, 2);
1779 return -ENODEV;
1780 }
1781 if ((ret = attach_mpu401(&cfg, THIS_MODULE)))
1782 return ret;
1783 }
1784
1785 return 0;
1786}
1787
1788static void __exit cleanup_mpu401(void)
1789{
1790 if (io != -1 && irq != -1) {
1791 /* Check for use by, for example, sscape driver */
1792 unload_mpu401(&cfg);
1793 }
1794}
1795
1796module_init(init_mpu401);
1797module_exit(cleanup_mpu401);
1798
1799#ifndef MODULE
1800static int __init setup_mpu401(char *str)
1801{
1802 /* io, irq */
1803 int ints[3];
1804
1805 str = get_options(str, ARRAY_SIZE(ints), ints);
1806
1807 io = ints[1];
1808 irq = ints[2];
1809
1810 return 1;
1811}
1812
1813__setup("mpu401=", setup_mpu401);
1814#endif
1815MODULE_LICENSE("GPL");