blob: 684de4c7c9c3c177c90112f374942cff1eda04fb [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# For a description of the syntax of this configuration file,
3# see Documentation/kbuild/kconfig-language.txt.
4#
5config M68K
6 bool
7 default y
8
9config MMU
10 bool
11 default y
12
Linus Torvalds1da177e2005-04-16 15:20:36 -070013config RWSEM_GENERIC_SPINLOCK
14 bool
15 default y
16
17config RWSEM_XCHGADD_ALGORITHM
18 bool
19
David Howellsf0d1b0b2006-12-08 02:37:49 -080020config ARCH_HAS_ILOG2_U32
21 bool
22 default n
23
24config ARCH_HAS_ILOG2_U64
25 bool
26 default n
27
Akinobu Mitaba1a5b32006-03-26 01:39:27 -080028config GENERIC_HWEIGHT
29 bool
30 default y
31
Linus Torvalds1da177e2005-04-16 15:20:36 -070032config GENERIC_CALIBRATE_DELAY
33 bool
34 default y
35
Ingo Molnar06027bd2006-02-14 13:53:15 -080036config TIME_LOW_RES
37 bool
38 default y
39
Al Virof9569e12007-07-20 04:32:58 +010040config GENERIC_IOMAP
41 bool
42 default y
43
viro@ZenIV.linux.org.uka08b6b72005-09-06 01:48:42 +010044config ARCH_MAY_HAVE_PC_FDC
45 bool
46 depends on Q40 || (BROKEN && SUN3X)
47 default y
48
Al Viro5ea81762007-02-11 15:41:31 +000049config NO_IOPORT
50 def_bool y
51
Linus Torvalds1da177e2005-04-16 15:20:36 -070052mainmenu "Linux/68k Kernel Configuration"
53
54source "init/Kconfig"
55
56menu "Platform dependent setup"
57
58config EISA
59 bool
60 ---help---
61 The Extended Industry Standard Architecture (EISA) bus was
62 developed as an open alternative to the IBM MicroChannel bus.
63
64 The EISA bus provided some of the features of the IBM MicroChannel
65 bus while maintaining backward compatibility with cards made for
66 the older ISA bus. The EISA bus saw limited use between 1988 and
67 1995 when it was made obsolete by the PCI bus.
68
69 Say Y here if you are building a kernel for an EISA-based machine.
70
71 Otherwise, say N.
72
73config MCA
74 bool
75 help
76 MicroChannel Architecture is found in some IBM PS/2 machines and
77 laptops. It is a bus system similar to PCI or ISA. See
78 <file:Documentation/mca.txt> (and especially the web page given
79 there) before attempting to build an MCA bus kernel.
80
81config PCMCIA
82 tristate
83 ---help---
84 Say Y here if you want to attach PCMCIA- or PC-cards to your Linux
85 computer. These are credit-card size devices such as network cards,
86 modems or hard drives often used with laptops computers. There are
87 actually two varieties of these cards: the older 16 bit PCMCIA cards
88 and the newer 32 bit CardBus cards. If you want to use CardBus
89 cards, you need to say Y here and also to "CardBus support" below.
90
91 To use your PC-cards, you will need supporting software from David
92 Hinds' pcmcia-cs package (see the file <file:Documentation/Changes>
93 for location). Please also read the PCMCIA-HOWTO, available from
94 <http://www.tldp.org/docs.html#howto>.
95
96 To compile this driver as modules, choose M here: the
97 modules will be called pcmcia_core and ds.
98
99config SUN3
100 bool "Sun3 support"
101 select M68020
102 select MMU_SUN3 if MMU
103 help
104 This option enables support for the Sun 3 series of workstations
105 (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires
106 that all other hardware types must be disabled, as Sun 3 kernels
107 are incompatible with all other m68k targets (including Sun 3x!).
108
109 If you don't want to compile a kernel exclusively for a Sun 3, say N.
110
111config AMIGA
112 bool "Amiga support"
113 depends on !MMU_SUN3
114 help
115 This option enables support for the Amiga series of computers. If
116 you plan to use this kernel on an Amiga, say Y here and browse the
117 material available in <file:Documentation/m68k>; otherwise say N.
118
119config ATARI
120 bool "Atari support"
121 depends on !MMU_SUN3
122 help
123 This option enables support for the 68000-based Atari series of
124 computers (including the TT, Falcon and Medusa). If you plan to use
125 this kernel on an Atari, say Y here and browse the material
126 available in <file:Documentation/m68k>; otherwise say N.
127
128config HADES
129 bool "Hades support"
130 depends on ATARI && BROKEN
131 help
132 This option enables support for the Hades Atari clone. If you plan
133 to use this kernel on a Hades, say Y here; otherwise say N.
134
135config PCI
136 bool
137 depends on HADES
138 default y
139 help
140 Find out whether you have a PCI motherboard. PCI is the name of a
141 bus system, i.e. the way the CPU talks to the other stuff inside
142 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
143 VESA. If you have PCI, say Y, otherwise N.
144
145 The PCI-HOWTO, available from
146 <http://www.tldp.org/docs.html#howto>, contains valuable
147 information about which PCI hardware does work under Linux and which
148 doesn't.
149
150config MAC
151 bool "Macintosh support"
152 depends on !MMU_SUN3
153 help
154 This option enables support for the Apple Macintosh series of
155 computers (yes, there is experimental support now, at least for part
156 of the series).
157
158 Say N unless you're willing to code the remaining necessary support.
159 ;)
160
161config NUBUS
162 bool
163 depends on MAC
164 default y
165
166config M68K_L2_CACHE
167 bool
168 depends on MAC
169 default y
170
171config APOLLO
172 bool "Apollo support"
173 depends on !MMU_SUN3
174 help
175 Say Y here if you want to run Linux on an MC680x0-based Apollo
176 Domain workstation such as the DN3500.
177
178config VME
179 bool "VME (Motorola and BVM) support"
180 depends on !MMU_SUN3
181 help
182 Say Y here if you want to build a kernel for a 680x0 based VME
183 board. Boards currently supported include Motorola boards MVME147,
184 MVME162, MVME166, MVME167, MVME172, and MVME177. BVME4000 and
185 BVME6000 boards from BVM Ltd are also supported.
186
187config MVME147
188 bool "MVME147 support"
189 depends on VME
190 help
191 Say Y to include support for early Motorola VME boards. This will
192 build a kernel which can run on MVME147 single-board computers. If
193 you select this option you will have to select the appropriate
194 drivers for SCSI, Ethernet and serial ports later on.
195
196config MVME16x
197 bool "MVME162, 166 and 167 support"
198 depends on VME
199 help
200 Say Y to include support for Motorola VME boards. This will build a
201 kernel which can run on MVME162, MVME166, MVME167, MVME172, and
202 MVME177 boards. If you select this option you will have to select
203 the appropriate drivers for SCSI, Ethernet and serial ports later
204 on.
205
206config BVME6000
207 bool "BVME4000 and BVME6000 support"
208 depends on VME
209 help
210 Say Y to include support for VME boards from BVM Ltd. This will
211 build a kernel which can run on BVME4000 and BVME6000 boards. If
212 you select this option you will have to select the appropriate
213 drivers for SCSI, Ethernet and serial ports later on.
214
215config HP300
216 bool "HP9000/300 and HP9000/400 support"
217 depends on !MMU_SUN3
218 help
219 This option enables support for the HP9000/300 and HP9000/400 series
220 of workstations. Support for these machines is still somewhat
221 experimental. If you plan to try to use the kernel on such a machine
222 say Y here.
223 Everybody else says N.
224
225config DIO
226 bool "DIO bus support"
227 depends on HP300
228 default y
229 help
230 Say Y here to enable support for the "DIO" expansion bus used in
231 HP300 machines. If you are using such a system you almost certainly
232 want this.
233
234config SUN3X
235 bool "Sun3x support"
236 depends on !MMU_SUN3
237 select M68030
238 help
239 This option enables support for the Sun 3x series of workstations.
240 Be warned that this support is very experimental.
241 Note that Sun 3x kernels are not compatible with Sun 3 hardware.
242 General Linux information on the Sun 3x series (now discontinued)
243 is at <http://www.angelfire.com/ca2/tech68k/sun3.html>.
244
245 If you don't want to compile a kernel for a Sun 3x, say N.
246
247config Q40
248 bool "Q40/Q60 support"
249 depends on !MMU_SUN3
250 help
251 The Q40 is a Motorola 68040-based successor to the Sinclair QL
252 manufactured in Germany. There is an official Q40 home page at
253 <http://www.q40.de/>. This option enables support for the Q40 and
254 Q60. Select your CPU below. For 68LC060 don't forget to enable FPU
255 emulation.
256
257comment "Processor type"
258
259config M68020
260 bool "68020 support"
261 help
262 If you anticipate running this kernel on a computer with a MC68020
263 processor, say Y. Otherwise, say N. Note that the 68020 requires a
264 68851 MMU (Memory Management Unit) to run Linux/m68k, except on the
265 Sun 3, which provides its own version.
266
267config M68030
268 bool "68030 support"
269 depends on !MMU_SUN3
270 help
271 If you anticipate running this kernel on a computer with a MC68030
272 processor, say Y. Otherwise, say N. Note that a MC68EC030 will not
273 work, as it does not include an MMU (Memory Management Unit).
274
275config M68040
276 bool "68040 support"
277 depends on !MMU_SUN3
278 help
279 If you anticipate running this kernel on a computer with a MC68LC040
280 or MC68040 processor, say Y. Otherwise, say N. Note that an
281 MC68EC040 will not work, as it does not include an MMU (Memory
282 Management Unit).
283
284config M68060
285 bool "68060 support"
286 depends on !MMU_SUN3
287 help
288 If you anticipate running this kernel on a computer with a MC68060
289 processor, say Y. Otherwise, say N.
290
291config MMU_MOTOROLA
292 bool
293 depends on MMU && !MMU_SUN3
294 default y
295
296config MMU_SUN3
297 bool
298
299config M68KFPU_EMU
300 bool "Math emulation support (EXPERIMENTAL)"
301 depends on EXPERIMENTAL
302 help
303 At some point in the future, this will cause floating-point math
304 instructions to be emulated by the kernel on machines that lack a
305 floating-point math coprocessor. Thrill-seekers and chronically
306 sleep-deprived psychotic hacker types can say Y now, everyone else
307 should probably wait a while.
308
309config M68KFPU_EMU_EXTRAPREC
310 bool "Math emulation extra precision"
311 depends on M68KFPU_EMU
312 help
313 The fpu uses normally a few bit more during calculations for
314 correct rounding, the emulator can (often) do the same but this
315 extra calculation can cost quite some time, so you can disable
316 it here. The emulator will then "only" calculate with a 64 bit
317 mantissa and round slightly incorrect, what is more then enough
318 for normal usage.
319
320config M68KFPU_EMU_ONLY
321 bool "Math emulation only kernel"
322 depends on M68KFPU_EMU
323 help
324 This option prevents any floating-point instructions from being
325 compiled into the kernel, thereby the kernel doesn't save any
326 floating point context anymore during task switches, so this
327 kernel will only be usable on machines without a floating-point
328 math coprocessor. This makes the kernel a bit faster as no tests
329 needs to be executed whether a floating-point instruction in the
330 kernel should be executed or not.
331
332config ADVANCED
333 bool "Advanced configuration options"
334 ---help---
335 This gives you access to some advanced options for the CPU. The
336 defaults should be fine for most users, but these options may make
337 it possible for you to improve performance somewhat if you know what
338 you are doing.
339
340 Note that the answer to this question won't directly affect the
341 kernel: saying N will just cause the configurator to skip all
342 the questions about these options.
343
344 Most users should say N to this question.
345
346config RMW_INSNS
347 bool "Use read-modify-write instructions"
348 depends on ADVANCED
349 ---help---
350 This allows to use certain instructions that work with indivisible
351 read-modify-write bus cycles. While this is faster than the
352 workaround of disabling interrupts, it can conflict with DMA
353 ( = direct memory access) on many Amiga systems, and it is also said
354 to destabilize other machines. It is very likely that this will
355 cause serious problems on any Amiga or Atari Medusa if set. The only
356 configuration where it should work are 68030-based Ataris, where it
357 apparently improves performance. But you've been warned! Unless you
358 really know what you are doing, say N. Try Y only if you're quite
359 adventurous.
360
361config SINGLE_MEMORY_CHUNK
Roman Zippel12d810c2007-05-31 00:40:54 -0700362 bool "Use one physical chunk of memory only" if ADVANCED && !SUN3
363 default y if SUN3
364 select NEED_MULTIPLE_NODES
Linus Torvalds1da177e2005-04-16 15:20:36 -0700365 help
366 Ignore all but the first contiguous chunk of physical memory for VM
367 purposes. This will save a few bytes kernel size and may speed up
368 some operations. Say N if not sure.
369
370config 060_WRITETHROUGH
371 bool "Use write-through caching for 68060 supervisor accesses"
372 depends on ADVANCED && M68060
373 ---help---
374 The 68060 generally uses copyback caching of recently accessed data.
375 Copyback caching means that memory writes will be held in an on-chip
376 cache and only written back to memory some time later. Saying Y
377 here will force supervisor (kernel) accesses to use writethrough
378 caching. Writethrough caching means that data is written to memory
379 straight away, so that cache and memory data always agree.
380 Writethrough caching is less efficient, but is needed for some
381 drivers on 68060 based systems where the 68060 bus snooping signal
382 is hardwired on. The 53c710 SCSI driver is known to suffer from
383 this problem.
384
Roman Zippel12d810c2007-05-31 00:40:54 -0700385config ARCH_DISCONTIGMEM_ENABLE
386 def_bool !SINGLE_MEMORY_CHUNK
387
388config NODES_SHIFT
389 int
390 default "3"
391 depends on !SINGLE_MEMORY_CHUNK
392
Dave Hansen3f22ab22005-06-23 00:07:43 -0700393source "mm/Kconfig"
394
Linus Torvalds1da177e2005-04-16 15:20:36 -0700395endmenu
396
397menu "General setup"
398
399source "fs/Kconfig.binfmt"
400
401config ZORRO
402 bool "Amiga Zorro (AutoConfig) bus support"
403 depends on AMIGA
404 help
405 This enables support for the Zorro bus in the Amiga. If you have
406 expansion cards in your Amiga that conform to the Amiga
407 AutoConfig(tm) specification, say Y, otherwise N. Note that even
408 expansion cards that do not fit in the Zorro slots but fit in e.g.
409 the CPU slot may fall in this category, so you have to say Y to let
410 Linux use these.
411
412config AMIGA_PCMCIA
413 bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)"
414 depends on AMIGA && EXPERIMENTAL
415 help
416 Include support in the kernel for pcmcia on Amiga 1200 and Amiga
417 600. If you intend to use pcmcia cards say Y; otherwise say N.
418
Linus Torvalds1da177e2005-04-16 15:20:36 -0700419config STRAM_PROC
420 bool "ST-RAM statistics in /proc"
421 depends on ATARI
422 help
Hugh Dickinsf9c98d02005-10-29 18:16:10 -0700423 Say Y here to report ST-RAM usage statistics in /proc/stram.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700424
425config HEARTBEAT
426 bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40
427 default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300
428 help
429 Use the power-on LED on your machine as a load meter. The exact
430 behavior is platform-dependent, but normally the flash frequency is
431 a hyperbolic function of the 5-minute load average.
432
433# We have a dedicated heartbeat LED. :-)
434config PROC_HARDWARE
435 bool "/proc/hardware support"
436 help
437 Say Y here to support the /proc/hardware file, which gives you
438 access to information about the machine you're running on,
439 including the model, CPU, MMU, clock speed, BogoMIPS rating,
440 and memory size.
441
442config ISA
443 bool
444 depends on Q40 || AMIGA_PCMCIA || GG2
445 default y
446 help
447 Find out whether you have ISA slots on your motherboard. ISA is the
448 name of a bus system, i.e. the way the CPU talks to the other stuff
449 inside your box. Other bus systems are PCI, EISA, MicroChannel
450 (MCA) or VESA. ISA is an older system, now being displaced by PCI;
451 newer boards don't support it. If you have ISA, say Y, otherwise N.
452
453config GENERIC_ISA_DMA
454 bool
455 depends on Q40 || AMIGA_PCMCIA || GG2
456 default y
457
Christoph Lameter5ac6da62007-02-10 01:43:14 -0800458config ZONE_DMA
459 bool
460 default y
461
Linus Torvalds1da177e2005-04-16 15:20:36 -0700462source "drivers/pci/Kconfig"
463
464source "drivers/zorro/Kconfig"
465
466endmenu
467
Sam Ravnborgd5950b42005-07-11 21:03:49 -0700468source "net/Kconfig"
469
Linus Torvalds1da177e2005-04-16 15:20:36 -0700470source "drivers/Kconfig"
471
472menu "Character devices"
473
474config ATARI_MFPSER
475 tristate "Atari MFP serial support"
476 depends on ATARI
477 ---help---
478 If you like to use the MFP serial ports ("Modem1", "Serial1") under
479 Linux, say Y. The driver equally supports all kinds of MFP serial
480 ports and automatically detects whether Serial1 is available.
481
482 To compile this driver as a module, choose M here.
483
484 Note for Falcon users: You also have an MFP port, it's just not
485 wired to the outside... But you could use the port under Linux.
486
487config ATARI_SCC
488 tristate "Atari SCC serial support"
489 depends on ATARI
490 ---help---
491 If you have serial ports based on a Zilog SCC chip (Modem2, Serial2,
492 LAN) and like to use them under Linux, say Y. All built-in SCC's are
493 supported (TT, MegaSTE, Falcon), and also the ST-ESCC. If you have
494 two connectors for channel A (Serial2 and LAN), they are visible as
495 two separate devices.
496
497 To compile this driver as a module, choose M here.
498
499config ATARI_SCC_DMA
500 bool "Atari SCC serial DMA support"
501 depends on ATARI_SCC
502 help
503 This enables DMA support for receiving data on channel A of the SCC.
504 If you have a TT you may say Y here and read
505 drivers/char/atari_SCC.README. All other users should say N here,
506 because only the TT has SCC-DMA, even if your machine keeps claiming
507 so at boot time.
508
509config ATARI_MIDI
510 tristate "Atari MIDI serial support"
511 depends on ATARI
512 help
513 If you want to use your Atari's MIDI port in Linux, say Y.
514
515 To compile this driver as a module, choose M here.
516
517config ATARI_DSP56K
518 tristate "Atari DSP56k support (EXPERIMENTAL)"
519 depends on ATARI && EXPERIMENTAL
520 help
521 If you want to be able to use the DSP56001 in Falcons, say Y. This
522 driver is still experimental, and if you don't know what it is, or
523 if you don't have this processor, just say N.
524
525 To compile this driver as a module, choose M here.
526
527config AMIGA_BUILTIN_SERIAL
528 tristate "Amiga builtin serial support"
529 depends on AMIGA
530 help
531 If you want to use your Amiga's built-in serial port in Linux,
532 answer Y.
533
534 To compile this driver as a module, choose M here.
535
536config WHIPPET_SERIAL
537 tristate "Hisoft Whippet PCMCIA serial support"
538 depends on AMIGA_PCMCIA
539 help
540 HiSoft has a web page at <http://www.hisoft.co.uk/>, but there
541 is no listing for the Whippet in their Amiga section.
542
543config MULTIFACE_III_TTY
544 tristate "Multiface Card III serial support"
545 depends on AMIGA
546 help
547 If you want to use a Multiface III card's serial port in Linux,
548 answer Y.
549
550 To compile this driver as a module, choose M here.
551
552config GVPIOEXT
553 tristate "GVP IO-Extender support"
554 depends on PARPORT=n && ZORRO
555 help
556 If you want to use a GVP IO-Extender serial card in Linux, say Y.
557 Otherwise, say N.
558
559config GVPIOEXT_LP
560 tristate "GVP IO-Extender parallel printer support"
561 depends on GVPIOEXT
562 help
563 Say Y to enable driving a printer from the parallel port on your
564 GVP IO-Extender card, N otherwise.
565
566config GVPIOEXT_PLIP
567 tristate "GVP IO-Extender PLIP support"
568 depends on GVPIOEXT
569 help
570 Say Y to enable doing IP over the parallel port on your GVP
571 IO-Extender card, N otherwise.
572
573config MAC_SCC
574 tristate "Macintosh serial support"
575 depends on MAC
576
577config MAC_HID
578 bool
579 depends on INPUT_ADBHID
580 default y
581
582config MAC_ADBKEYCODES
583 bool "Support for ADB raw keycodes"
584 depends on INPUT_ADBHID
585 help
586 This provides support for sending raw ADB keycodes to console
587 devices. This is the default up to 2.4.0, but in future this may be
588 phased out in favor of generic Linux keycodes. If you say Y here,
589 you can dynamically switch via the
590 /proc/sys/dev/mac_hid/keyboard_sends_linux_keycodes
591 sysctl and with the "keyboard_sends_linux_keycodes=" kernel
592 argument.
593
594 If unsure, say Y here.
595
596config ADB_KEYBOARD
597 bool "Support for ADB keyboard (old driver)"
598 depends on MAC && !INPUT_ADBHID
599 help
600 This option allows you to use an ADB keyboard attached to your
601 machine. Note that this disables any other (ie. PS/2) keyboard
602 support, even if your machine is physically capable of using both at
603 the same time.
604
605 If you use an ADB keyboard (4 pin connector), say Y here.
606 If you use a PS/2 keyboard (6 pin connector), say N here.
607
608config HPDCA
609 tristate "HP DCA serial support"
610 depends on DIO && SERIAL_8250
611 help
612 If you want to use the internal "DCA" serial ports on an HP300
613 machine, say Y here.
614
615config HPAPCI
616 tristate "HP APCI serial support"
617 depends on HP300 && SERIAL_8250 && EXPERIMENTAL
618 help
619 If you want to use the internal "APCI" serial ports on an HP400
620 machine, say Y here.
621
622config MVME147_SCC
623 bool "SCC support for MVME147 serial ports"
624 depends on MVME147
625 help
626 This is the driver for the serial ports on the Motorola MVME147
627 boards. Everyone using one of these boards should say Y here.
628
629config SERIAL167
630 bool "CD2401 support for MVME166/7 serial ports"
Geert Uytterhoevenea62aa12006-10-09 22:27:42 +0200631 depends on MVME16x
Linus Torvalds1da177e2005-04-16 15:20:36 -0700632 help
633 This is the driver for the serial ports on the Motorola MVME166,
634 167, and 172 boards. Everyone using one of these boards should say
635 Y here.
636
637config MVME162_SCC
638 bool "SCC support for MVME162 serial ports"
639 depends on MVME16x
640 help
641 This is the driver for the serial ports on the Motorola MVME162 and
642 172 boards. Everyone using one of these boards should say Y here.
643
644config BVME6000_SCC
645 bool "SCC support for BVME6000 serial ports"
646 depends on BVME6000
647 help
648 This is the driver for the serial ports on the BVME4000 and BVME6000
649 boards from BVM Ltd. Everyone using one of these boards should say
650 Y here.
651
652config DN_SERIAL
653 bool "Support for DN serial port (dummy)"
654 depends on APOLLO
655
656config SERIAL_CONSOLE
657 bool "Support for serial port console"
658 depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_SCC=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
659 ---help---
660 If you say Y here, it will be possible to use a serial port as the
661 system console (the system console is the device which receives all
662 kernel messages and warnings and which allows logins in single user
663 mode). This could be useful if some terminal or printer is connected
664 to that serial port.
665
666 Even if you say Y here, the currently visible virtual console
667 (/dev/tty0) will still be used as the system console by default, but
668 you can alter that using a kernel command line option such as
669 "console=ttyS1". (Try "man bootparam" or see the documentation of
670 your boot loader (lilo or loadlin) about how to pass options to the
671 kernel at boot time.)
672
673 If you don't have a VGA card installed and you say Y here, the
674 kernel will automatically use the first serial line, /dev/ttyS0, as
675 system console.
676
677 If unsure, say N.
678
679endmenu
680
681source "fs/Kconfig"
682
683source "arch/m68k/Kconfig.debug"
684
685source "security/Kconfig"
686
687source "crypto/Kconfig"
688
689source "lib/Kconfig"