blob: db451ae0a36811427165b9d0431d3b38d356ec8e [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* $Id: $
2 * linux/drivers/scsi/wd7000.c
3 *
4 * Copyright (C) 1992 Thomas Wuensche
5 * closely related to the aha1542 driver from Tommy Thorn
6 * ( as close as different hardware allows on a lowlevel-driver :-) )
7 *
8 * Revised (and renamed) by John Boyd <boyd@cis.ohio-state.edu> to
9 * accommodate Eric Youngdale's modifications to scsi.c. Nov 1992.
10 *
11 * Additional changes to support scatter/gather. Dec. 1992. tw/jb
12 *
13 * No longer tries to reset SCSI bus at boot (it wasn't working anyway).
14 * Rewritten to support multiple host adapters.
15 * Miscellaneous cleanup.
16 * So far, still doesn't do reset or abort correctly, since I have no idea
17 * how to do them with this board (8^(. Jan 1994 jb
18 *
19 * This driver now supports both of the two standard configurations (per
20 * the 3.36 Owner's Manual, my latest reference) by the same method as
21 * before; namely, by looking for a BIOS signature. Thus, the location of
22 * the BIOS signature determines the board configuration. Until I have
23 * time to do something more flexible, users should stick to one of the
24 * following:
25 *
26 * Standard configuration for single-adapter systems:
27 * - BIOS at CE00h
28 * - I/O base address 350h
29 * - IRQ level 15
30 * - DMA channel 6
31 * Standard configuration for a second adapter in a system:
32 * - BIOS at C800h
33 * - I/O base address 330h
34 * - IRQ level 11
35 * - DMA channel 5
36 *
37 * Anyone who can recompile the kernel is welcome to add others as need
38 * arises, but unpredictable results may occur if there are conflicts.
39 * In any event, if there are multiple adapters in a system, they MUST
40 * use different I/O bases, IRQ levels, and DMA channels, since they will be
41 * indistinguishable (and in direct conflict) otherwise.
42 *
43 * As a point of information, the NO_OP command toggles the CMD_RDY bit
44 * of the status port, and this fact could be used as a test for the I/O
45 * base address (or more generally, board detection). There is an interrupt
46 * status port, so IRQ probing could also be done. I suppose the full
47 * DMA diagnostic could be used to detect the DMA channel being used. I
48 * haven't done any of this, though, because I think there's too much of
49 * a chance that such explorations could be destructive, if some other
50 * board's resources are used inadvertently. So, call me a wimp, but I
51 * don't want to try it. The only kind of exploration I trust is memory
52 * exploration, since it's more certain that reading memory won't be
53 * destructive.
54 *
55 * More to my liking would be a LILO boot command line specification, such
56 * as is used by the aha152x driver (and possibly others). I'll look into
57 * it, as I have time...
58 *
59 * I get mail occasionally from people who either are using or are
60 * considering using a WD7000 with Linux. There is a variety of
61 * nomenclature describing WD7000's. To the best of my knowledge, the
62 * following is a brief summary (from an old WD doc - I don't work for
63 * them or anything like that):
64 *
65 * WD7000-FASST2: This is a WD7000 board with the real-mode SST ROM BIOS
66 * installed. Last I heard, the BIOS was actually done by Columbia
67 * Data Products. The BIOS is only used by this driver (and thus
68 * by Linux) to identify the board; none of it can be executed under
69 * Linux.
70 *
71 * WD7000-ASC: This is the original adapter board, with or without BIOS.
72 * The board uses a WD33C93 or WD33C93A SBIC, which in turn is
73 * controlled by an onboard Z80 processor. The board interface
74 * visible to the host CPU is defined effectively by the Z80's
75 * firmware, and it is this firmware's revision level that is
76 * determined and reported by this driver. (The version of the
77 * on-board BIOS is of no interest whatsoever.) The host CPU has
78 * no access to the SBIC; hence the fact that it is a WD33C93 is
79 * also of no interest to this driver.
80 *
81 * WD7000-AX:
82 * WD7000-MX:
83 * WD7000-EX: These are newer versions of the WD7000-ASC. The -ASC is
84 * largely built from discrete components; these boards use more
85 * integration. The -AX is an ISA bus board (like the -ASC),
86 * the -MX is an MCA (i.e., PS/2) bus board), and the -EX is an
87 * EISA bus board.
88 *
89 * At the time of my documentation, the -?X boards were "future" products,
90 * and were not yet available. However, I vaguely recall that Thomas
91 * Wuensche had an -AX, so I believe at least it is supported by this
92 * driver. I have no personal knowledge of either -MX or -EX boards.
93 *
94 * P.S. Just recently, I've discovered (directly from WD and Future
95 * Domain) that all but the WD7000-EX have been out of production for
96 * two years now. FD has production rights to the 7000-EX, and are
97 * producing it under a new name, and with a new BIOS. If anyone has
98 * one of the FD boards, it would be nice to come up with a signature
99 * for it.
100 * J.B. Jan 1994.
101 *
102 *
103 * Revisions by Miroslav Zagorac <zaga@fly.cc.fer.hr>
104 *
105 * 08/24/1996.
106 *
107 * Enhancement for wd7000_detect function has been made, so you don't have
108 * to enter BIOS ROM address in initialisation data (see struct Config).
109 * We cannot detect IRQ, DMA and I/O base address for now, so we have to
110 * enter them as arguments while wd_7000 is detected. If someone has IRQ,
111 * DMA or I/O base address set to some other value, he can enter them in
112 * configuration without any problem. Also I wrote a function wd7000_setup,
113 * so now you can enter WD-7000 definition as kernel arguments,
114 * as in lilo.conf:
115 *
116 * append="wd7000=IRQ,DMA,IO"
117 *
118 * PS: If card BIOS ROM is disabled, function wd7000_detect now will recognize
119 * adapter, unlike the old one. Anyway, BIOS ROM from WD7000 adapter is
120 * useless for Linux. B^)
121 *
122 *
123 * 09/06/1996.
124 *
125 * Autodetecting of I/O base address from wd7000_detect function is removed,
126 * some little bugs removed, etc...
127 *
128 * Thanks to Roger Scott for driver debugging.
129 *
130 * 06/07/1997
131 *
132 * Added support for /proc file system (/proc/scsi/wd7000/[0...] files).
133 * Now, driver can handle hard disks with capacity >1GB.
134 *
135 * 01/15/1998
136 *
137 * Added support for BUS_ON and BUS_OFF parameters in config line.
138 * Miscellaneous cleanup.
139 *
140 * 03/01/1998
141 *
142 * WD7000 driver now work on kernels >= 2.1.x
143 *
144 *
145 * 12/31/2001 - Arnaldo Carvalho de Melo <acme@conectiva.com.br>
146 *
147 * use host->host_lock, not io_request_lock, cleanups
148 *
Alan Coxfa195af2008-10-27 15:16:36 +0000149 * 2002/10/04 - Alan Cox <alan@lxorguk.ukuu.org.uk>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700150 *
Harvey Harrisoncadbd4a2008-07-03 23:47:27 -0700151 * Use dev_id for interrupts, kill __func__ pasting
Linus Torvalds1da177e2005-04-16 15:20:36 -0700152 * Add a lock for the scb pool, clean up all other cli/sti usage stuff
153 * Use the adapter lock for the other places we had the cli's
154 *
Alan Coxfa195af2008-10-27 15:16:36 +0000155 * 2002/10/06 - Alan Cox <alan@lxorguk.ukuu.org.uk>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700156 *
157 * Switch to new style error handling
158 * Clean up delay to udelay, and yielding sleeps
159 * Make host reset actually reset the card
160 * Make everything static
161 *
162 * 2003/02/12 - Christoph Hellwig <hch@infradead.org>
163 *
Adam Buchbinder6070d812009-12-04 15:47:01 -0500164 * Cleaned up host template definition
Linus Torvalds1da177e2005-04-16 15:20:36 -0700165 * Removed now obsolete wd7000.h
166 */
167
168#include <linux/delay.h>
169#include <linux/module.h>
170#include <linux/interrupt.h>
171#include <linux/kernel.h>
172#include <linux/types.h>
173#include <linux/string.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700174#include <linux/spinlock.h>
175#include <linux/ioport.h>
176#include <linux/proc_fs.h>
177#include <linux/blkdev.h>
178#include <linux/init.h>
179#include <linux/stat.h>
Matthew Wilcox53d5ed62006-10-11 01:22:01 -0700180#include <linux/io.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700181
182#include <asm/system.h>
183#include <asm/dma.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700184
185#include <scsi/scsi.h>
186#include <scsi/scsi_cmnd.h>
187#include <scsi/scsi_device.h>
188#include <scsi/scsi_host.h>
189#include <scsi/scsicam.h>
190
191
192#undef WD7000_DEBUG /* general debug */
193#ifdef WD7000_DEBUG
194#define dprintk printk
195#else
196#define dprintk(format,args...)
197#endif
198
199/*
200 * Mailbox structure sizes.
201 * I prefer to keep the number of ICMBs much larger than the number of
202 * OGMBs. OGMBs are used very quickly by the driver to start one or
203 * more commands, while ICMBs are used by the host adapter per command.
204 */
205#define OGMB_CNT 16
206#define ICMB_CNT 32
207
208/*
209 * Scb's are shared by all active adapters. So, if they all become busy,
210 * callers may be made to wait in alloc_scbs for them to free. That can
211 * be avoided by setting MAX_SCBS to NUM_CONFIG * WD7000_Q. If you'd
212 * rather conserve memory, use a smaller number (> 0, of course) - things
213 * will should still work OK.
214 */
215#define MAX_SCBS 32
216
217/*
218 * In this version, sg_tablesize now defaults to WD7000_SG, and will
219 * be set to SG_NONE for older boards. This is the reverse of the
220 * previous default, and was changed so that the driver-level
221 * scsi_host_template would reflect the driver's support for scatter/
222 * gather.
223 *
224 * Also, it has been reported that boards at Revision 6 support scatter/
225 * gather, so the new definition of an "older" board has been changed
226 * accordingly.
227 */
228#define WD7000_Q 16
229#define WD7000_SG 16
230
231
232/*
233 * WD7000-specific mailbox structure
234 *
235 */
236typedef volatile struct mailbox {
237 unchar status;
238 unchar scbptr[3]; /* SCSI-style - MSB first (big endian) */
239} Mailbox;
240
241/*
242 * This structure should contain all per-adapter global data. I.e., any
243 * new global per-adapter data should put in here.
244 */
245typedef struct adapter {
246 struct Scsi_Host *sh; /* Pointer to Scsi_Host structure */
247 int iobase; /* This adapter's I/O base address */
248 int irq; /* This adapter's IRQ level */
249 int dma; /* This adapter's DMA channel */
250 int int_counter; /* This adapter's interrupt counter */
251 int bus_on; /* This adapter's BUS_ON time */
252 int bus_off; /* This adapter's BUS_OFF time */
253 struct { /* This adapter's mailboxes */
254 Mailbox ogmb[OGMB_CNT]; /* Outgoing mailboxes */
255 Mailbox icmb[ICMB_CNT]; /* Incoming mailboxes */
256 } mb;
257 int next_ogmb; /* to reduce contention at mailboxes */
258 unchar control; /* shadows CONTROL port value */
259 unchar rev1, rev2; /* filled in by wd7000_revision */
260} Adapter;
261
262/*
263 * (linear) base address for ROM BIOS
264 */
265static const long wd7000_biosaddr[] = {
266 0xc0000, 0xc2000, 0xc4000, 0xc6000, 0xc8000, 0xca000, 0xcc000, 0xce000,
267 0xd0000, 0xd2000, 0xd4000, 0xd6000, 0xd8000, 0xda000, 0xdc000, 0xde000
268};
Tobias Klauser6391a112006-06-08 22:23:48 -0700269#define NUM_ADDRS ARRAY_SIZE(wd7000_biosaddr)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700270
271static const unsigned short wd7000_iobase[] = {
272 0x0300, 0x0308, 0x0310, 0x0318, 0x0320, 0x0328, 0x0330, 0x0338,
273 0x0340, 0x0348, 0x0350, 0x0358, 0x0360, 0x0368, 0x0370, 0x0378,
274 0x0380, 0x0388, 0x0390, 0x0398, 0x03a0, 0x03a8, 0x03b0, 0x03b8,
275 0x03c0, 0x03c8, 0x03d0, 0x03d8, 0x03e0, 0x03e8, 0x03f0, 0x03f8
276};
Tobias Klauser6391a112006-06-08 22:23:48 -0700277#define NUM_IOPORTS ARRAY_SIZE(wd7000_iobase)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700278
279static const short wd7000_irq[] = { 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 };
Tobias Klauser6391a112006-06-08 22:23:48 -0700280#define NUM_IRQS ARRAY_SIZE(wd7000_irq)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700281
282static const short wd7000_dma[] = { 5, 6, 7 };
Tobias Klauser6391a112006-06-08 22:23:48 -0700283#define NUM_DMAS ARRAY_SIZE(wd7000_dma)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700284
285/*
286 * The following is set up by wd7000_detect, and used thereafter for
287 * proc and other global ookups
288 */
289
290#define UNITS 8
291static struct Scsi_Host *wd7000_host[UNITS];
292
293#define BUS_ON 64 /* x 125ns = 8000ns (BIOS default) */
294#define BUS_OFF 15 /* x 125ns = 1875ns (BIOS default) */
295
296/*
297 * Standard Adapter Configurations - used by wd7000_detect
298 */
299typedef struct {
300 short irq; /* IRQ level */
301 short dma; /* DMA channel */
302 unsigned iobase; /* I/O base address */
303 short bus_on; /* Time that WD7000 spends on the AT-bus when */
304 /* transferring data. BIOS default is 8000ns. */
305 short bus_off; /* Time that WD7000 spends OFF THE BUS after */
306 /* while it is transferring data. */
307 /* BIOS default is 1875ns */
308} Config;
309
310/*
311 * Add here your configuration...
312 */
313static Config configs[] = {
314 {15, 6, 0x350, BUS_ON, BUS_OFF}, /* defaults for single adapter */
315 {11, 5, 0x320, BUS_ON, BUS_OFF}, /* defaults for second adapter */
316 {7, 6, 0x350, BUS_ON, BUS_OFF}, /* My configuration (Zaga) */
317 {-1, -1, 0x0, BUS_ON, BUS_OFF} /* Empty slot */
318};
Tobias Klauser6391a112006-06-08 22:23:48 -0700319#define NUM_CONFIGS ARRAY_SIZE(configs)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700320
321/*
322 * The following list defines strings to look for in the BIOS that identify
323 * it as the WD7000-FASST2 SST BIOS. I suspect that something should be
324 * added for the Future Domain version.
325 */
326typedef struct signature {
327 const char *sig; /* String to look for */
328 unsigned long ofs; /* offset from BIOS base address */
329 unsigned len; /* length of string */
330} Signature;
331
332static const Signature signatures[] = {
333 {"SSTBIOS", 0x0000d, 7} /* "SSTBIOS" @ offset 0x0000d */
334};
Tobias Klauser6391a112006-06-08 22:23:48 -0700335#define NUM_SIGNATURES ARRAY_SIZE(signatures)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700336
337
338/*
339 * I/O Port Offsets and Bit Definitions
340 * 4 addresses are used. Those not defined here are reserved.
341 */
342#define ASC_STAT 0 /* Status, Read */
343#define ASC_COMMAND 0 /* Command, Write */
344#define ASC_INTR_STAT 1 /* Interrupt Status, Read */
345#define ASC_INTR_ACK 1 /* Acknowledge, Write */
346#define ASC_CONTROL 2 /* Control, Write */
347
348/*
349 * ASC Status Port
350 */
351#define INT_IM 0x80 /* Interrupt Image Flag */
352#define CMD_RDY 0x40 /* Command Port Ready */
353#define CMD_REJ 0x20 /* Command Port Byte Rejected */
354#define ASC_INIT 0x10 /* ASC Initialized Flag */
355#define ASC_STATMASK 0xf0 /* The lower 4 Bytes are reserved */
356
357/*
358 * COMMAND opcodes
359 *
360 * Unfortunately, I have no idea how to properly use some of these commands,
361 * as the OEM manual does not make it clear. I have not been able to use
362 * enable/disable unsolicited interrupts or the reset commands with any
363 * discernible effect whatsoever. I think they may be related to certain
364 * ICB commands, but again, the OEM manual doesn't make that clear.
365 */
366#define NO_OP 0 /* NO-OP toggles CMD_RDY bit in ASC_STAT */
367#define INITIALIZATION 1 /* initialization (10 bytes) */
368#define DISABLE_UNS_INTR 2 /* disable unsolicited interrupts */
369#define ENABLE_UNS_INTR 3 /* enable unsolicited interrupts */
370#define INTR_ON_FREE_OGMB 4 /* interrupt on free OGMB */
371#define SOFT_RESET 5 /* SCSI bus soft reset */
372#define HARD_RESET_ACK 6 /* SCSI bus hard reset acknowledge */
373#define START_OGMB 0x80 /* start command in OGMB (n) */
374#define SCAN_OGMBS 0xc0 /* start multiple commands, signature (n) */
375 /* where (n) = lower 6 bits */
376/*
377 * For INITIALIZATION:
378 */
379typedef struct initCmd {
380 unchar op; /* command opcode (= 1) */
381 unchar ID; /* Adapter's SCSI ID */
382 unchar bus_on; /* Bus on time, x 125ns (see below) */
383 unchar bus_off; /* Bus off time, "" "" */
384 unchar rsvd; /* Reserved */
385 unchar mailboxes[3]; /* Address of Mailboxes, MSB first */
386 unchar ogmbs; /* Number of outgoing MBs, max 64, 0,1 = 1 */
387 unchar icmbs; /* Number of incoming MBs, "" "" */
388} InitCmd;
389
390/*
391 * Interrupt Status Port - also returns diagnostic codes at ASC reset
392 *
393 * if msb is zero, the lower bits are diagnostic status
394 * Diagnostics:
395 * 01 No diagnostic error occurred
396 * 02 RAM failure
397 * 03 FIFO R/W failed
398 * 04 SBIC register read/write failed
399 * 05 Initialization D-FF failed
400 * 06 Host IRQ D-FF failed
401 * 07 ROM checksum error
402 * Interrupt status (bitwise):
403 * 10NNNNNN outgoing mailbox NNNNNN is free
404 * 11NNNNNN incoming mailbox NNNNNN needs service
405 */
406#define MB_INTR 0xC0 /* Mailbox Service possible/required */
407#define IMB_INTR 0x40 /* 1 Incoming / 0 Outgoing */
408#define MB_MASK 0x3f /* mask for mailbox number */
409
410/*
411 * CONTROL port bits
412 */
413#define INT_EN 0x08 /* Interrupt Enable */
414#define DMA_EN 0x04 /* DMA Enable */
415#define SCSI_RES 0x02 /* SCSI Reset */
416#define ASC_RES 0x01 /* ASC Reset */
417
418/*
419 * Driver data structures:
420 * - mb and scbs are required for interfacing with the host adapter.
421 * An SCB has extra fields not visible to the adapter; mb's
422 * _cannot_ do this, since the adapter assumes they are contiguous in
423 * memory, 4 bytes each, with ICMBs following OGMBs, and uses this fact
424 * to access them.
425 * - An icb is for host-only (non-SCSI) commands. ICBs are 16 bytes each;
426 * the additional bytes are used only by the driver.
427 * - For now, a pool of SCBs are kept in global storage by this driver,
428 * and are allocated and freed as needed.
429 *
430 * The 7000-FASST2 marks OGMBs empty as soon as it has _started_ a command,
431 * not when it has finished. Since the SCB must be around for completion,
432 * problems arise when SCBs correspond to OGMBs, which may be reallocated
433 * earlier (or delayed unnecessarily until a command completes).
434 * Mailboxes are used as transient data structures, simply for
435 * carrying SCB addresses to/from the 7000-FASST2.
436 *
437 * Note also since SCBs are not "permanently" associated with mailboxes,
438 * there is no need to keep a global list of scsi_cmnd pointers indexed
439 * by OGMB. Again, SCBs reference their scsi_cmnds directly, so mailbox
440 * indices need not be involved.
441 */
442
443/*
444 * WD7000-specific scatter/gather element structure
445 */
446typedef struct sgb {
447 unchar len[3];
448 unchar ptr[3]; /* Also SCSI-style - MSB first */
449} Sgb;
450
451typedef struct scb { /* Command Control Block 5.4.1 */
452 unchar op; /* Command Control Block Operation Code */
453 unchar idlun; /* op=0,2:Target Id, op=1:Initiator Id */
454 /* Outbound data transfer, length is checked */
455 /* Inbound data transfer, length is checked */
456 /* Logical Unit Number */
457 unchar cdb[12]; /* SCSI Command Block */
458 volatile unchar status; /* SCSI Return Status */
459 volatile unchar vue; /* Vendor Unique Error Code */
460 unchar maxlen[3]; /* Maximum Data Transfer Length */
461 unchar dataptr[3]; /* SCSI Data Block Pointer */
462 unchar linkptr[3]; /* Next Command Link Pointer */
463 unchar direc; /* Transfer Direction */
464 unchar reserved2[6]; /* SCSI Command Descriptor Block */
465 /* end of hardware SCB */
466 struct scsi_cmnd *SCpnt;/* scsi_cmnd using this SCB */
467 Sgb sgb[WD7000_SG]; /* Scatter/gather list for this SCB */
468 Adapter *host; /* host adapter */
469 struct scb *next; /* for lists of scbs */
470} Scb;
471
472/*
473 * This driver is written to allow host-only commands to be executed.
474 * These use a 16-byte block called an ICB. The format is extended by the
475 * driver to 18 bytes, to support the status returned in the ICMB and
476 * an execution phase code.
477 *
478 * There are other formats besides these; these are the ones I've tried
479 * to use. Formats for some of the defined ICB opcodes are not defined
480 * (notably, get/set unsolicited interrupt status) in my copy of the OEM
481 * manual, and others are ambiguous/hard to follow.
482 */
483#define ICB_OP_MASK 0x80 /* distinguishes scbs from icbs */
484#define ICB_OP_OPEN_RBUF 0x80 /* open receive buffer */
485#define ICB_OP_RECV_CMD 0x81 /* receive command from initiator */
486#define ICB_OP_RECV_DATA 0x82 /* receive data from initiator */
487#define ICB_OP_RECV_SDATA 0x83 /* receive data with status from init. */
488#define ICB_OP_SEND_DATA 0x84 /* send data with status to initiator */
489#define ICB_OP_SEND_STAT 0x86 /* send command status to initiator */
490 /* 0x87 is reserved */
491#define ICB_OP_READ_INIT 0x88 /* read initialization bytes */
492#define ICB_OP_READ_ID 0x89 /* read adapter's SCSI ID */
493#define ICB_OP_SET_UMASK 0x8A /* set unsolicited interrupt mask */
494#define ICB_OP_GET_UMASK 0x8B /* read unsolicited interrupt mask */
495#define ICB_OP_GET_REVISION 0x8C /* read firmware revision level */
496#define ICB_OP_DIAGNOSTICS 0x8D /* execute diagnostics */
497#define ICB_OP_SET_EPARMS 0x8E /* set execution parameters */
498#define ICB_OP_GET_EPARMS 0x8F /* read execution parameters */
499
500typedef struct icbRecvCmd {
501 unchar op;
502 unchar IDlun; /* Initiator SCSI ID/lun */
503 unchar len[3]; /* command buffer length */
504 unchar ptr[3]; /* command buffer address */
505 unchar rsvd[7]; /* reserved */
506 volatile unchar vue; /* vendor-unique error code */
507 volatile unchar status; /* returned (icmb) status */
508 volatile unchar phase; /* used by interrupt handler */
509} IcbRecvCmd;
510
511typedef struct icbSendStat {
512 unchar op;
513 unchar IDlun; /* Target SCSI ID/lun */
514 unchar stat; /* (outgoing) completion status byte 1 */
515 unchar rsvd[12]; /* reserved */
516 volatile unchar vue; /* vendor-unique error code */
517 volatile unchar status; /* returned (icmb) status */
518 volatile unchar phase; /* used by interrupt handler */
519} IcbSendStat;
520
521typedef struct icbRevLvl {
522 unchar op;
523 volatile unchar primary; /* primary revision level (returned) */
524 volatile unchar secondary; /* secondary revision level (returned) */
525 unchar rsvd[12]; /* reserved */
526 volatile unchar vue; /* vendor-unique error code */
527 volatile unchar status; /* returned (icmb) status */
528 volatile unchar phase; /* used by interrupt handler */
529} IcbRevLvl;
530
531typedef struct icbUnsMask { /* I'm totally guessing here */
532 unchar op;
533 volatile unchar mask[14]; /* mask bits */
534#if 0
535 unchar rsvd[12]; /* reserved */
536#endif
537 volatile unchar vue; /* vendor-unique error code */
538 volatile unchar status; /* returned (icmb) status */
539 volatile unchar phase; /* used by interrupt handler */
540} IcbUnsMask;
541
542typedef struct icbDiag {
543 unchar op;
544 unchar type; /* diagnostics type code (0-3) */
545 unchar len[3]; /* buffer length */
546 unchar ptr[3]; /* buffer address */
547 unchar rsvd[7]; /* reserved */
548 volatile unchar vue; /* vendor-unique error code */
549 volatile unchar status; /* returned (icmb) status */
550 volatile unchar phase; /* used by interrupt handler */
551} IcbDiag;
552
553#define ICB_DIAG_POWERUP 0 /* Power-up diags only */
554#define ICB_DIAG_WALKING 1 /* walking 1's pattern */
555#define ICB_DIAG_DMA 2 /* DMA - system memory diags */
556#define ICB_DIAG_FULL 3 /* do both 1 & 2 */
557
558typedef struct icbParms {
559 unchar op;
560 unchar rsvd1; /* reserved */
561 unchar len[3]; /* parms buffer length */
562 unchar ptr[3]; /* parms buffer address */
563 unchar idx[2]; /* index (MSB-LSB) */
564 unchar rsvd2[5]; /* reserved */
565 volatile unchar vue; /* vendor-unique error code */
566 volatile unchar status; /* returned (icmb) status */
567 volatile unchar phase; /* used by interrupt handler */
568} IcbParms;
569
570typedef struct icbAny {
571 unchar op;
572 unchar data[14]; /* format-specific data */
573 volatile unchar vue; /* vendor-unique error code */
574 volatile unchar status; /* returned (icmb) status */
575 volatile unchar phase; /* used by interrupt handler */
576} IcbAny;
577
578typedef union icb {
579 unchar op; /* ICB opcode */
580 IcbRecvCmd recv_cmd; /* format for receive command */
581 IcbSendStat send_stat; /* format for send status */
582 IcbRevLvl rev_lvl; /* format for get revision level */
583 IcbDiag diag; /* format for execute diagnostics */
584 IcbParms eparms; /* format for get/set exec parms */
585 IcbAny icb; /* generic format */
586 unchar data[18];
587} Icb;
588
589#ifdef MODULE
590static char *wd7000;
591module_param(wd7000, charp, 0);
592#endif
593
594/*
595 * Driver SCB structure pool.
596 *
597 * The SCBs declared here are shared by all host adapters; hence, this
598 * structure is not part of the Adapter structure.
599 */
600static Scb scbs[MAX_SCBS];
601static Scb *scbfree; /* free list */
602static int freescbs = MAX_SCBS; /* free list counter */
603static spinlock_t scbpool_lock; /* guards the scb free list and count */
604
605/*
606 * END of data/declarations - code follows.
607 */
608static void __init setup_error(char *mesg, int *ints)
609{
610 if (ints[0] == 3)
611 printk(KERN_ERR "wd7000_setup: \"wd7000=%d,%d,0x%x\" -> %s\n", ints[1], ints[2], ints[3], mesg);
612 else if (ints[0] == 4)
613 printk(KERN_ERR "wd7000_setup: \"wd7000=%d,%d,0x%x,%d\" -> %s\n", ints[1], ints[2], ints[3], ints[4], mesg);
614 else
615 printk(KERN_ERR "wd7000_setup: \"wd7000=%d,%d,0x%x,%d,%d\" -> %s\n", ints[1], ints[2], ints[3], ints[4], ints[5], mesg);
616}
617
618
619/*
620 * Note: You can now set these options from the kernel's "command line".
621 * The syntax is:
622 *
623 * wd7000=<IRQ>,<DMA>,<IO>[,<BUS_ON>[,<BUS_OFF>]]
624 *
625 * , where BUS_ON and BUS_OFF are in nanoseconds. BIOS default values
626 * are 8000ns for BUS_ON and 1875ns for BUS_OFF.
627 * eg:
628 * wd7000=7,6,0x350
629 *
630 * will configure the driver for a WD-7000 controller
631 * using IRQ 15 with a DMA channel 6, at IO base address 0x350.
632 */
633static int __init wd7000_setup(char *str)
634{
635 static short wd7000_card_num; /* .bss will zero this */
636 short i;
637 int ints[6];
638
639 (void) get_options(str, ARRAY_SIZE(ints), ints);
640
641 if (wd7000_card_num >= NUM_CONFIGS) {
Harvey Harrisoncadbd4a2008-07-03 23:47:27 -0700642 printk(KERN_ERR "%s: Too many \"wd7000=\" configurations in " "command line!\n", __func__);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700643 return 0;
644 }
645
646 if ((ints[0] < 3) || (ints[0] > 5)) {
Harvey Harrisoncadbd4a2008-07-03 23:47:27 -0700647 printk(KERN_ERR "%s: Error in command line! " "Usage: wd7000=<IRQ>,<DMA>,IO>[,<BUS_ON>" "[,<BUS_OFF>]]\n", __func__);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700648 } else {
649 for (i = 0; i < NUM_IRQS; i++)
650 if (ints[1] == wd7000_irq[i])
651 break;
652
653 if (i == NUM_IRQS) {
654 setup_error("invalid IRQ.", ints);
655 return 0;
656 } else
657 configs[wd7000_card_num].irq = ints[1];
658
659 for (i = 0; i < NUM_DMAS; i++)
660 if (ints[2] == wd7000_dma[i])
661 break;
662
663 if (i == NUM_DMAS) {
664 setup_error("invalid DMA channel.", ints);
665 return 0;
666 } else
667 configs[wd7000_card_num].dma = ints[2];
668
669 for (i = 0; i < NUM_IOPORTS; i++)
670 if (ints[3] == wd7000_iobase[i])
671 break;
672
673 if (i == NUM_IOPORTS) {
674 setup_error("invalid I/O base address.", ints);
675 return 0;
676 } else
677 configs[wd7000_card_num].iobase = ints[3];
678
679 if (ints[0] > 3) {
680 if ((ints[4] < 500) || (ints[4] > 31875)) {
681 setup_error("BUS_ON value is out of range (500" " to 31875 nanoseconds)!", ints);
682 configs[wd7000_card_num].bus_on = BUS_ON;
683 } else
684 configs[wd7000_card_num].bus_on = ints[4] / 125;
685 } else
686 configs[wd7000_card_num].bus_on = BUS_ON;
687
688 if (ints[0] > 4) {
689 if ((ints[5] < 500) || (ints[5] > 31875)) {
690 setup_error("BUS_OFF value is out of range (500" " to 31875 nanoseconds)!", ints);
691 configs[wd7000_card_num].bus_off = BUS_OFF;
692 } else
693 configs[wd7000_card_num].bus_off = ints[5] / 125;
694 } else
695 configs[wd7000_card_num].bus_off = BUS_OFF;
696
697 if (wd7000_card_num) {
698 for (i = 0; i < (wd7000_card_num - 1); i++) {
699 int j = i + 1;
700
701 for (; j < wd7000_card_num; j++)
702 if (configs[i].irq == configs[j].irq) {
703 setup_error("duplicated IRQ!", ints);
704 return 0;
705 }
706 if (configs[i].dma == configs[j].dma) {
707 setup_error("duplicated DMA " "channel!", ints);
708 return 0;
709 }
710 if (configs[i].iobase == configs[j].iobase) {
711 setup_error("duplicated I/O " "base address!", ints);
712 return 0;
713 }
714 }
715 }
716
717 dprintk(KERN_DEBUG "wd7000_setup: IRQ=%d, DMA=%d, I/O=0x%x, "
718 "BUS_ON=%dns, BUS_OFF=%dns\n", configs[wd7000_card_num].irq, configs[wd7000_card_num].dma, configs[wd7000_card_num].iobase, configs[wd7000_card_num].bus_on * 125, configs[wd7000_card_num].bus_off * 125);
719
720 wd7000_card_num++;
721 }
722 return 1;
723}
724
725__setup("wd7000=", wd7000_setup);
726
727static inline void any2scsi(unchar * scsi, int any)
728{
729 *scsi++ = (unsigned)any >> 16;
730 *scsi++ = (unsigned)any >> 8;
731 *scsi++ = any;
732}
733
734static inline int scsi2int(unchar * scsi)
735{
736 return (scsi[0] << 16) | (scsi[1] << 8) | scsi[2];
737}
738
739static inline void wd7000_enable_intr(Adapter * host)
740{
741 host->control |= INT_EN;
742 outb(host->control, host->iobase + ASC_CONTROL);
743}
744
745
746static inline void wd7000_enable_dma(Adapter * host)
747{
748 unsigned long flags;
749 host->control |= DMA_EN;
750 outb(host->control, host->iobase + ASC_CONTROL);
751
752 flags = claim_dma_lock();
753 set_dma_mode(host->dma, DMA_MODE_CASCADE);
754 enable_dma(host->dma);
755 release_dma_lock(flags);
756
757}
758
759
760#define WAITnexttimeout 200 /* 2 seconds */
761
762static inline short WAIT(unsigned port, unsigned mask, unsigned allof, unsigned noneof)
763{
764 unsigned WAITbits;
765 unsigned long WAITtimeout = jiffies + WAITnexttimeout;
766
767 while (time_before_eq(jiffies, WAITtimeout)) {
768 WAITbits = inb(port) & mask;
769
770 if (((WAITbits & allof) == allof) && ((WAITbits & noneof) == 0))
771 return (0);
772 }
773
774 return (1);
775}
776
777
778static inline int command_out(Adapter * host, unchar * cmd, int len)
779{
780 if (!WAIT(host->iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0)) {
781 while (len--) {
782 do {
783 outb(*cmd, host->iobase + ASC_COMMAND);
784 WAIT(host->iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0);
785 } while (inb(host->iobase + ASC_STAT) & CMD_REJ);
786
787 cmd++;
788 }
789
790 return (1);
791 }
792
793 printk(KERN_WARNING "wd7000 command_out: WAIT failed(%d)\n", len + 1);
794
795 return (0);
796}
797
798
799/*
800 * This version of alloc_scbs is in preparation for supporting multiple
801 * commands per lun and command chaining, by queueing pending commands.
802 * We will need to allocate Scbs in blocks since they will wait to be
803 * executed so there is the possibility of deadlock otherwise.
804 * Also, to keep larger requests from being starved by smaller requests,
805 * we limit access to this routine with an internal busy flag, so that
806 * the satisfiability of a request is not dependent on the size of the
807 * request.
808 */
809static inline Scb *alloc_scbs(struct Scsi_Host *host, int needed)
810{
811 Scb *scb, *p = NULL;
812 unsigned long flags;
813 unsigned long timeout = jiffies + WAITnexttimeout;
814 unsigned long now;
815 int i;
816
817 if (needed <= 0)
818 return (NULL); /* sanity check */
819
820 spin_unlock_irq(host->host_lock);
821
822 retry:
823 while (freescbs < needed) {
824 timeout = jiffies + WAITnexttimeout;
825 do {
826 /* FIXME: can we actually just yield here ?? */
827 for (now = jiffies; now == jiffies;)
828 cpu_relax(); /* wait a jiffy */
829 } while (freescbs < needed && time_before_eq(jiffies, timeout));
830 /*
831 * If we get here with enough free Scbs, we can take them.
832 * Otherwise, we timed out and didn't get enough.
833 */
834 if (freescbs < needed) {
835 printk(KERN_ERR "wd7000: can't get enough free SCBs.\n");
836 return (NULL);
837 }
838 }
839
840 /* Take the lock, then check we didnt get beaten, if so try again */
841 spin_lock_irqsave(&scbpool_lock, flags);
842 if (freescbs < needed) {
843 spin_unlock_irqrestore(&scbpool_lock, flags);
844 goto retry;
845 }
846
847 scb = scbfree;
848 freescbs -= needed;
849 for (i = 0; i < needed; i++) {
850 p = scbfree;
851 scbfree = p->next;
852 }
853 p->next = NULL;
854
855 spin_unlock_irqrestore(&scbpool_lock, flags);
856
857 spin_lock_irq(host->host_lock);
858 return (scb);
859}
860
861
862static inline void free_scb(Scb * scb)
863{
864 unsigned long flags;
865
866 spin_lock_irqsave(&scbpool_lock, flags);
867
868 memset(scb, 0, sizeof(Scb));
869 scb->next = scbfree;
870 scbfree = scb;
871 freescbs++;
872
873 spin_unlock_irqrestore(&scbpool_lock, flags);
874}
875
876
877static inline void init_scbs(void)
878{
879 int i;
880
881 spin_lock_init(&scbpool_lock);
882
883 /* This is only ever called before the SCB pool is active */
884
885 scbfree = &(scbs[0]);
886 memset(scbs, 0, sizeof(scbs));
887 for (i = 0; i < MAX_SCBS - 1; i++) {
888 scbs[i].next = &(scbs[i + 1]);
889 scbs[i].SCpnt = NULL;
890 }
891 scbs[MAX_SCBS - 1].next = NULL;
892 scbs[MAX_SCBS - 1].SCpnt = NULL;
893}
894
895
896static int mail_out(Adapter * host, Scb * scbptr)
897/*
898 * Note: this can also be used for ICBs; just cast to the parm type.
899 */
900{
901 int i, ogmb;
902 unsigned long flags;
903 unchar start_ogmb;
904 Mailbox *ogmbs = host->mb.ogmb;
905 int *next_ogmb = &(host->next_ogmb);
906
907 dprintk("wd7000_mail_out: 0x%06lx", (long) scbptr);
908
909 /* We first look for a free outgoing mailbox */
910 spin_lock_irqsave(host->sh->host_lock, flags);
911 ogmb = *next_ogmb;
912 for (i = 0; i < OGMB_CNT; i++) {
913 if (ogmbs[ogmb].status == 0) {
914 dprintk(" using OGMB 0x%x", ogmb);
915 ogmbs[ogmb].status = 1;
916 any2scsi((unchar *) ogmbs[ogmb].scbptr, (int) scbptr);
917
918 *next_ogmb = (ogmb + 1) % OGMB_CNT;
919 break;
920 } else
921 ogmb = (ogmb + 1) % OGMB_CNT;
922 }
923 spin_unlock_irqrestore(host->sh->host_lock, flags);
924
925 dprintk(", scb is 0x%06lx", (long) scbptr);
926
927 if (i >= OGMB_CNT) {
928 /*
929 * Alternatively, we might issue the "interrupt on free OGMB",
930 * and sleep, but it must be ensured that it isn't the init
931 * task running. Instead, this version assumes that the caller
932 * will be persistent, and try again. Since it's the adapter
933 * that marks OGMB's free, waiting even with interrupts off
934 * should work, since they are freed very quickly in most cases.
935 */
936 dprintk(", no free OGMBs.\n");
937 return (0);
938 }
939
940 wd7000_enable_intr(host);
941
942 start_ogmb = START_OGMB | ogmb;
943 command_out(host, &start_ogmb, 1);
944
945 dprintk(", awaiting interrupt.\n");
946
947 return (1);
948}
949
950
951static int make_code(unsigned hosterr, unsigned scsierr)
952{
953#ifdef WD7000_DEBUG
954 int in_error = hosterr;
955#endif
956
957 switch ((hosterr >> 8) & 0xff) {
958 case 0: /* Reserved */
959 hosterr = DID_ERROR;
960 break;
961 case 1: /* Command Complete, no errors */
962 hosterr = DID_OK;
963 break;
964 case 2: /* Command complete, error logged in scb status (scsierr) */
965 hosterr = DID_OK;
966 break;
967 case 4: /* Command failed to complete - timeout */
968 hosterr = DID_TIME_OUT;
969 break;
970 case 5: /* Command terminated; Bus reset by external device */
971 hosterr = DID_RESET;
972 break;
973 case 6: /* Unexpected Command Received w/ host as target */
974 hosterr = DID_BAD_TARGET;
975 break;
976 case 80: /* Unexpected Reselection */
977 case 81: /* Unexpected Selection */
978 hosterr = DID_BAD_INTR;
979 break;
980 case 82: /* Abort Command Message */
981 hosterr = DID_ABORT;
982 break;
983 case 83: /* SCSI Bus Software Reset */
984 case 84: /* SCSI Bus Hardware Reset */
985 hosterr = DID_RESET;
986 break;
987 default: /* Reserved */
988 hosterr = DID_ERROR;
989 }
990#ifdef WD7000_DEBUG
991 if (scsierr || hosterr)
992 dprintk("\nSCSI command error: SCSI 0x%02x host 0x%04x return %d\n", scsierr, in_error, hosterr);
993#endif
994 return (scsierr | (hosterr << 16));
995}
996
997#define wd7000_intr_ack(host) outb (0, host->iobase + ASC_INTR_ACK)
998
999
David Howells7d12e782006-10-05 14:55:46 +01001000static irqreturn_t wd7000_intr(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001001{
1002 Adapter *host = (Adapter *) dev_id;
1003 int flag, icmb, errstatus, icmb_status;
1004 int host_error, scsi_error;
1005 Scb *scb; /* for SCSI commands */
1006 IcbAny *icb; /* for host commands */
1007 struct scsi_cmnd *SCpnt;
1008 Mailbox *icmbs = host->mb.icmb;
1009 unsigned long flags;
1010
1011 spin_lock_irqsave(host->sh->host_lock, flags);
1012 host->int_counter++;
1013
1014 dprintk("wd7000_intr: irq = %d, host = 0x%06lx\n", irq, (long) host);
1015
1016 flag = inb(host->iobase + ASC_INTR_STAT);
1017
1018 dprintk("wd7000_intr: intr stat = 0x%02x\n", flag);
1019
1020 if (!(inb(host->iobase + ASC_STAT) & INT_IM)) {
1021 /* NB: these are _very_ possible if IRQ 15 is being used, since
1022 * it's the "garbage collector" on the 2nd 8259 PIC. Specifically,
1023 * any interrupt signal into the 8259 which can't be identified
1024 * comes out as 7 from the 8259, which is 15 to the host. Thus, it
1025 * is a good thing the WD7000 has an interrupt status port, so we
1026 * can sort these out. Otherwise, electrical noise and other such
1027 * problems would be indistinguishable from valid interrupts...
1028 */
1029 dprintk("wd7000_intr: phantom interrupt...\n");
1030 goto ack;
1031 }
1032
1033 if (!(flag & MB_INTR))
1034 goto ack;
1035
1036 /* The interrupt is for a mailbox */
1037 if (!(flag & IMB_INTR)) {
1038 dprintk("wd7000_intr: free outgoing mailbox\n");
1039 /*
1040 * If sleep_on() and the "interrupt on free OGMB" command are
1041 * used in mail_out(), wake_up() should correspondingly be called
1042 * here. For now, we don't need to do anything special.
1043 */
1044 goto ack;
1045 }
1046
1047 /* The interrupt is for an incoming mailbox */
1048 icmb = flag & MB_MASK;
1049 icmb_status = icmbs[icmb].status;
1050 if (icmb_status & 0x80) { /* unsolicited - result in ICMB */
1051 dprintk("wd7000_intr: unsolicited interrupt 0x%02x\n", icmb_status);
1052 goto ack;
1053 }
1054
1055 /* Aaaargh! (Zaga) */
1056 scb = isa_bus_to_virt(scsi2int((unchar *) icmbs[icmb].scbptr));
1057 icmbs[icmb].status = 0;
1058 if (scb->op & ICB_OP_MASK) { /* an SCB is done */
1059 icb = (IcbAny *) scb;
1060 icb->status = icmb_status;
1061 icb->phase = 0;
1062 goto ack;
1063 }
1064
1065 SCpnt = scb->SCpnt;
1066 if (--(SCpnt->SCp.phase) <= 0) { /* all scbs are done */
1067 host_error = scb->vue | (icmb_status << 8);
1068 scsi_error = scb->status;
1069 errstatus = make_code(host_error, scsi_error);
1070 SCpnt->result = errstatus;
1071
1072 free_scb(scb);
1073
1074 SCpnt->scsi_done(SCpnt);
1075 }
1076
1077 ack:
1078 dprintk("wd7000_intr: return from interrupt handler\n");
1079 wd7000_intr_ack(host);
1080
1081 spin_unlock_irqrestore(host->sh->host_lock, flags);
1082 return IRQ_HANDLED;
1083}
1084
Jeff Garzikf2812332010-11-16 02:10:29 -05001085static int wd7000_queuecommand_lck(struct scsi_cmnd *SCpnt,
Linus Torvalds1da177e2005-04-16 15:20:36 -07001086 void (*done)(struct scsi_cmnd *))
1087{
1088 Scb *scb;
1089 Sgb *sgb;
1090 unchar *cdb = (unchar *) SCpnt->cmnd;
1091 unchar idlun;
1092 short cdblen;
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001093 int nseg;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001094 Adapter *host = (Adapter *) SCpnt->device->host->hostdata;
1095
1096 cdblen = SCpnt->cmd_len;
1097 idlun = ((SCpnt->device->id << 5) & 0xe0) | (SCpnt->device->lun & 7);
1098 SCpnt->scsi_done = done;
1099 SCpnt->SCp.phase = 1;
1100 scb = alloc_scbs(SCpnt->device->host, 1);
1101 scb->idlun = idlun;
1102 memcpy(scb->cdb, cdb, cdblen);
1103 scb->direc = 0x40; /* Disable direction check */
1104
1105 scb->SCpnt = SCpnt; /* so we can find stuff later */
1106 SCpnt->host_scribble = (unchar *) scb;
1107 scb->host = host;
1108
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001109 nseg = scsi_sg_count(SCpnt);
Boaz Harrosh9a3dd652007-11-05 11:21:40 +02001110 if (nseg > 1) {
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001111 struct scatterlist *sg;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001112 unsigned i;
1113
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001114 dprintk("Using scatter/gather with %d elements.\n", nseg);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001115
1116 sgb = scb->sgb;
1117 scb->op = 1;
1118 any2scsi(scb->dataptr, (int) sgb);
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001119 any2scsi(scb->maxlen, nseg * sizeof(Sgb));
Linus Torvalds1da177e2005-04-16 15:20:36 -07001120
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001121 scsi_for_each_sg(SCpnt, sg, nseg, i) {
Jens Axboe45711f12007-10-22 21:19:53 +02001122 any2scsi(sgb[i].ptr, isa_page_to_bus(sg_page(sg)) + sg->offset);
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001123 any2scsi(sgb[i].len, sg->length);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001124 }
1125 } else {
1126 scb->op = 0;
Boaz Harrosh9a3dd652007-11-05 11:21:40 +02001127 if (nseg) {
1128 struct scatterlist *sg = scsi_sglist(SCpnt);
1129 any2scsi(scb->dataptr, isa_page_to_bus(sg_page(sg)) + sg->offset);
1130 }
FUJITA Tomonorie7d6cf52007-05-14 19:27:06 +09001131 any2scsi(scb->maxlen, scsi_bufflen(SCpnt));
Linus Torvalds1da177e2005-04-16 15:20:36 -07001132 }
1133
1134 /* FIXME: drop lock and yield here ? */
1135
1136 while (!mail_out(host, scb))
1137 cpu_relax(); /* keep trying */
1138
1139 return 0;
1140}
1141
Jeff Garzikf2812332010-11-16 02:10:29 -05001142static DEF_SCSI_QCMD(wd7000_queuecommand)
1143
Linus Torvalds1da177e2005-04-16 15:20:36 -07001144static int wd7000_diagnostics(Adapter * host, int code)
1145{
1146 static IcbDiag icb = { ICB_OP_DIAGNOSTICS };
1147 static unchar buf[256];
1148 unsigned long timeout;
1149
1150 icb.type = code;
1151 any2scsi(icb.len, sizeof(buf));
1152 any2scsi(icb.ptr, (int) &buf);
1153 icb.phase = 1;
1154 /*
1155 * This routine is only called at init, so there should be OGMBs
1156 * available. I'm assuming so here. If this is going to
1157 * fail, I can just let the timeout catch the failure.
1158 */
1159 mail_out(host, (struct scb *) &icb);
1160 timeout = jiffies + WAITnexttimeout; /* wait up to 2 seconds */
1161 while (icb.phase && time_before(jiffies, timeout)) {
1162 cpu_relax(); /* wait for completion */
1163 barrier();
1164 }
1165
1166 if (icb.phase) {
1167 printk("wd7000_diagnostics: timed out.\n");
1168 return (0);
1169 }
1170 if (make_code(icb.vue | (icb.status << 8), 0)) {
1171 printk("wd7000_diagnostics: failed (0x%02x,0x%02x)\n", icb.vue, icb.status);
1172 return (0);
1173 }
1174
1175 return (1);
1176}
1177
1178
1179static int wd7000_adapter_reset(Adapter * host)
1180{
1181 InitCmd init_cmd = {
1182 INITIALIZATION,
1183 7,
1184 host->bus_on,
1185 host->bus_off,
1186 0,
1187 {0, 0, 0},
1188 OGMB_CNT,
1189 ICMB_CNT
1190 };
1191 int diag;
1192 /*
1193 * Reset the adapter - only. The SCSI bus was initialized at power-up,
1194 * and we need to do this just so we control the mailboxes, etc.
1195 */
1196 outb(ASC_RES, host->iobase + ASC_CONTROL);
1197 udelay(40); /* reset pulse: this is 40us, only need 25us */
1198 outb(0, host->iobase + ASC_CONTROL);
1199 host->control = 0; /* this must always shadow ASC_CONTROL */
1200
1201 if (WAIT(host->iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0)) {
1202 printk(KERN_ERR "wd7000_init: WAIT timed out.\n");
1203 return -1; /* -1 = not ok */
1204 }
1205
1206 if ((diag = inb(host->iobase + ASC_INTR_STAT)) != 1) {
1207 printk("wd7000_init: ");
1208
1209 switch (diag) {
1210 case 2:
1211 printk(KERN_ERR "RAM failure.\n");
1212 break;
1213 case 3:
1214 printk(KERN_ERR "FIFO R/W failed\n");
1215 break;
1216 case 4:
1217 printk(KERN_ERR "SBIC register R/W failed\n");
1218 break;
1219 case 5:
1220 printk(KERN_ERR "Initialization D-FF failed.\n");
1221 break;
1222 case 6:
1223 printk(KERN_ERR "Host IRQ D-FF failed.\n");
1224 break;
1225 case 7:
1226 printk(KERN_ERR "ROM checksum error.\n");
1227 break;
1228 default:
1229 printk(KERN_ERR "diagnostic code 0x%02Xh received.\n", diag);
1230 }
1231 return -1;
1232 }
1233 /* Clear mailboxes */
1234 memset(&(host->mb), 0, sizeof(host->mb));
1235
1236 /* Execute init command */
1237 any2scsi((unchar *) & (init_cmd.mailboxes), (int) &(host->mb));
1238 if (!command_out(host, (unchar *) & init_cmd, sizeof(init_cmd))) {
1239 printk(KERN_ERR "wd7000_adapter_reset: adapter initialization failed.\n");
1240 return -1;
1241 }
1242
1243 if (WAIT(host->iobase + ASC_STAT, ASC_STATMASK, ASC_INIT, 0)) {
1244 printk("wd7000_adapter_reset: WAIT timed out.\n");
1245 return -1;
1246 }
1247 return 0;
1248}
1249
1250static int wd7000_init(Adapter * host)
1251{
1252 if (wd7000_adapter_reset(host) == -1)
1253 return 0;
1254
1255
Thomas Gleixner1d6f3592006-07-01 19:29:42 -07001256 if (request_irq(host->irq, wd7000_intr, IRQF_DISABLED, "wd7000", host)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -07001257 printk("wd7000_init: can't get IRQ %d.\n", host->irq);
1258 return (0);
1259 }
1260 if (request_dma(host->dma, "wd7000")) {
1261 printk("wd7000_init: can't get DMA channel %d.\n", host->dma);
1262 free_irq(host->irq, host);
1263 return (0);
1264 }
1265 wd7000_enable_dma(host);
1266 wd7000_enable_intr(host);
1267
1268 if (!wd7000_diagnostics(host, ICB_DIAG_FULL)) {
1269 free_dma(host->dma);
1270 free_irq(host->irq, NULL);
1271 return (0);
1272 }
1273
1274 return (1);
1275}
1276
1277
1278static void wd7000_revision(Adapter * host)
1279{
1280 static IcbRevLvl icb = { ICB_OP_GET_REVISION };
1281
1282 icb.phase = 1;
1283 /*
1284 * Like diagnostics, this is only done at init time, in fact, from
1285 * wd7000_detect, so there should be OGMBs available. If it fails,
1286 * the only damage will be that the revision will show up as 0.0,
1287 * which in turn means that scatter/gather will be disabled.
1288 */
1289 mail_out(host, (struct scb *) &icb);
1290 while (icb.phase) {
1291 cpu_relax(); /* wait for completion */
1292 barrier();
1293 }
1294 host->rev1 = icb.primary;
1295 host->rev2 = icb.secondary;
1296}
1297
1298
1299#undef SPRINTF
1300#define SPRINTF(args...) { if (pos < (buffer + length)) pos += sprintf (pos, ## args); }
1301
1302static int wd7000_set_info(char *buffer, int length, struct Scsi_Host *host)
1303{
1304 dprintk("Buffer = <%.*s>, length = %d\n", length, buffer, length);
1305
1306 /*
1307 * Currently this is a no-op
1308 */
1309 dprintk("Sorry, this function is currently out of order...\n");
1310 return (length);
1311}
1312
1313
1314static int wd7000_proc_info(struct Scsi_Host *host, char *buffer, char **start, off_t offset, int length, int inout)
1315{
1316 Adapter *adapter = (Adapter *)host->hostdata;
1317 unsigned long flags;
1318 char *pos = buffer;
1319#ifdef WD7000_DEBUG
1320 Mailbox *ogmbs, *icmbs;
1321 short count;
1322#endif
1323
1324 /*
1325 * Has data been written to the file ?
1326 */
1327 if (inout)
1328 return (wd7000_set_info(buffer, length, host));
1329
1330 spin_lock_irqsave(host->host_lock, flags);
1331 SPRINTF("Host scsi%d: Western Digital WD-7000 (rev %d.%d)\n", host->host_no, adapter->rev1, adapter->rev2);
1332 SPRINTF(" IO base: 0x%x\n", adapter->iobase);
1333 SPRINTF(" IRQ: %d\n", adapter->irq);
1334 SPRINTF(" DMA channel: %d\n", adapter->dma);
1335 SPRINTF(" Interrupts: %d\n", adapter->int_counter);
1336 SPRINTF(" BUS_ON time: %d nanoseconds\n", adapter->bus_on * 125);
1337 SPRINTF(" BUS_OFF time: %d nanoseconds\n", adapter->bus_off * 125);
1338
1339#ifdef WD7000_DEBUG
1340 ogmbs = adapter->mb.ogmb;
1341 icmbs = adapter->mb.icmb;
1342
1343 SPRINTF("\nControl port value: 0x%x\n", adapter->control);
1344 SPRINTF("Incoming mailbox:\n");
1345 SPRINTF(" size: %d\n", ICMB_CNT);
1346 SPRINTF(" queued messages: ");
1347
1348 for (i = count = 0; i < ICMB_CNT; i++)
1349 if (icmbs[i].status) {
1350 count++;
1351 SPRINTF("0x%x ", i);
1352 }
1353
1354 SPRINTF(count ? "\n" : "none\n");
1355
1356 SPRINTF("Outgoing mailbox:\n");
1357 SPRINTF(" size: %d\n", OGMB_CNT);
1358 SPRINTF(" next message: 0x%x\n", adapter->next_ogmb);
1359 SPRINTF(" queued messages: ");
1360
1361 for (i = count = 0; i < OGMB_CNT; i++)
1362 if (ogmbs[i].status) {
1363 count++;
1364 SPRINTF("0x%x ", i);
1365 }
1366
1367 SPRINTF(count ? "\n" : "none\n");
1368#endif
1369
1370 spin_unlock_irqrestore(host->host_lock, flags);
1371
1372 /*
1373 * Calculate start of next buffer, and return value.
1374 */
1375 *start = buffer + offset;
1376
1377 if ((pos - buffer) < offset)
1378 return (0);
1379 else if ((pos - buffer - offset) < length)
1380 return (pos - buffer - offset);
1381 else
1382 return (length);
1383}
1384
1385
1386/*
1387 * Returns the number of adapters this driver is supporting.
1388 *
1389 * The source for hosts.c says to wait to call scsi_register until 100%
1390 * sure about an adapter. We need to do it a little sooner here; we
1391 * need the storage set up by scsi_register before wd7000_init, and
1392 * changing the location of an Adapter structure is more trouble than
1393 * calling scsi_unregister.
1394 *
1395 */
1396
Randy.Dunlapb9bcf9c2006-06-25 05:48:05 -07001397static __init int wd7000_detect(struct scsi_host_template *tpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001398{
1399 short present = 0, biosaddr_ptr, sig_ptr, i, pass;
1400 short biosptr[NUM_CONFIGS];
1401 unsigned iobase;
1402 Adapter *host = NULL;
1403 struct Scsi_Host *sh;
1404 int unit = 0;
1405
1406 dprintk("wd7000_detect: started\n");
1407
1408#ifdef MODULE
1409 if (wd7000)
1410 wd7000_setup(wd7000);
1411#endif
1412
1413 for (i = 0; i < UNITS; wd7000_host[i++] = NULL);
1414 for (i = 0; i < NUM_CONFIGS; biosptr[i++] = -1);
1415
1416 tpnt->proc_name = "wd7000";
1417 tpnt->proc_info = &wd7000_proc_info;
1418
1419 /*
1420 * Set up SCB free list, which is shared by all adapters
1421 */
1422 init_scbs();
1423
1424 for (pass = 0; pass < NUM_CONFIGS; pass++) {
1425 /*
1426 * First, search for BIOS SIGNATURE...
1427 */
1428 for (biosaddr_ptr = 0; biosaddr_ptr < NUM_ADDRS; biosaddr_ptr++)
1429 for (sig_ptr = 0; sig_ptr < NUM_SIGNATURES; sig_ptr++) {
1430 for (i = 0; i < pass; i++)
1431 if (biosptr[i] == biosaddr_ptr)
1432 break;
1433
1434 if (i == pass) {
1435 void __iomem *biosaddr = ioremap(wd7000_biosaddr[biosaddr_ptr] + signatures[sig_ptr].ofs,
1436 signatures[sig_ptr].len);
1437 short bios_match = 1;
1438
1439 if (biosaddr)
1440 bios_match = check_signature(biosaddr, signatures[sig_ptr].sig, signatures[sig_ptr].len);
1441
1442 iounmap(biosaddr);
1443
1444 if (bios_match)
1445 goto bios_matched;
1446 }
1447 }
1448
1449 bios_matched:
1450 /*
1451 * BIOS SIGNATURE has been found.
1452 */
1453#ifdef WD7000_DEBUG
1454 dprintk("wd7000_detect: pass %d\n", pass + 1);
1455
1456 if (biosaddr_ptr == NUM_ADDRS)
1457 dprintk("WD-7000 SST BIOS not detected...\n");
1458 else
1459 dprintk("WD-7000 SST BIOS detected at 0x%lx: checking...\n", wd7000_biosaddr[biosaddr_ptr]);
1460#endif
1461
1462 if (configs[pass].irq < 0)
1463 continue;
1464
1465 if (unit == UNITS)
1466 continue;
1467
1468 iobase = configs[pass].iobase;
1469
1470 dprintk("wd7000_detect: check IO 0x%x region...\n", iobase);
1471
1472 if (request_region(iobase, 4, "wd7000")) {
1473
1474 dprintk("wd7000_detect: ASC reset (IO 0x%x) ...", iobase);
1475 /*
1476 * ASC reset...
1477 */
1478 outb(ASC_RES, iobase + ASC_CONTROL);
1479 msleep(10);
1480 outb(0, iobase + ASC_CONTROL);
1481
1482 if (WAIT(iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0)) {
1483 dprintk("failed!\n");
1484 goto err_release;
1485 } else
1486 dprintk("ok!\n");
1487
1488 if (inb(iobase + ASC_INTR_STAT) == 1) {
1489 /*
1490 * We register here, to get a pointer to the extra space,
1491 * which we'll use as the Adapter structure (host) for
1492 * this adapter. It is located just after the registered
1493 * Scsi_Host structure (sh), and is located by the empty
1494 * array hostdata.
1495 */
1496 sh = scsi_register(tpnt, sizeof(Adapter));
1497 if (sh == NULL)
1498 goto err_release;
1499
1500 host = (Adapter *) sh->hostdata;
1501
1502 dprintk("wd7000_detect: adapter allocated at 0x%x\n", (int) host);
1503 memset(host, 0, sizeof(Adapter));
1504
1505 host->irq = configs[pass].irq;
1506 host->dma = configs[pass].dma;
1507 host->iobase = iobase;
1508 host->int_counter = 0;
1509 host->bus_on = configs[pass].bus_on;
1510 host->bus_off = configs[pass].bus_off;
1511 host->sh = wd7000_host[unit] = sh;
1512 unit++;
1513
1514 dprintk("wd7000_detect: Trying init WD-7000 card at IO " "0x%x, IRQ %d, DMA %d...\n", host->iobase, host->irq, host->dma);
1515
1516 if (!wd7000_init(host)) /* Initialization failed */
1517 goto err_unregister;
1518
1519 /*
1520 * OK from here - we'll use this adapter/configuration.
1521 */
1522 wd7000_revision(host); /* important for scatter/gather */
1523
1524 /*
1525 * For boards before rev 6.0, scatter/gather isn't supported.
1526 */
1527 if (host->rev1 < 6)
Boaz Harrosh9a3dd652007-11-05 11:21:40 +02001528 sh->sg_tablesize = 1;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001529
1530 present++; /* count it */
1531
1532 if (biosaddr_ptr != NUM_ADDRS)
1533 biosptr[pass] = biosaddr_ptr;
1534
1535 printk(KERN_INFO "Western Digital WD-7000 (rev %d.%d) ", host->rev1, host->rev2);
1536 printk("using IO 0x%x, IRQ %d, DMA %d.\n", host->iobase, host->irq, host->dma);
1537 printk(" BUS_ON time: %dns, BUS_OFF time: %dns\n", host->bus_on * 125, host->bus_off * 125);
1538 }
1539 } else
1540 dprintk("wd7000_detect: IO 0x%x region already allocated!\n", iobase);
1541
1542 continue;
1543
1544 err_unregister:
1545 scsi_unregister(sh);
1546 err_release:
1547 release_region(iobase, 4);
1548
1549 }
1550
1551 if (!present)
1552 printk("Failed initialization of WD-7000 SCSI card!\n");
1553
1554 return (present);
1555}
1556
1557static int wd7000_release(struct Scsi_Host *shost)
1558{
1559 if (shost->irq)
1560 free_irq(shost->irq, NULL);
1561 if (shost->io_port && shost->n_io_port)
1562 release_region(shost->io_port, shost->n_io_port);
1563 scsi_unregister(shost);
1564 return 0;
1565}
1566
1567#if 0
1568/*
1569 * I have absolutely NO idea how to do an abort with the WD7000...
1570 */
1571static int wd7000_abort(Scsi_Cmnd * SCpnt)
1572{
1573 Adapter *host = (Adapter *) SCpnt->device->host->hostdata;
1574
1575 if (inb(host->iobase + ASC_STAT) & INT_IM) {
1576 printk("wd7000_abort: lost interrupt\n");
1577 wd7000_intr_handle(host->irq, NULL, NULL);
1578 return FAILED;
1579 }
1580 return FAILED;
1581}
1582#endif
1583
1584/*
1585 * Last resort. Reinitialize the board.
1586 */
1587
1588static int wd7000_host_reset(struct scsi_cmnd *SCpnt)
1589{
1590 Adapter *host = (Adapter *) SCpnt->device->host->hostdata;
1591
Dan Carpentera8f23b02010-04-01 18:55:16 +03001592 spin_lock_irq(SCpnt->device->host->host_lock);
Jeff Garzik df0ae242005-05-28 07:57:14 -04001593
1594 if (wd7000_adapter_reset(host) < 0) {
1595 spin_unlock_irq(SCpnt->device->host->host_lock);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001596 return FAILED;
Jeff Garzik df0ae242005-05-28 07:57:14 -04001597 }
1598
Linus Torvalds1da177e2005-04-16 15:20:36 -07001599 wd7000_enable_intr(host);
Jeff Garzik df0ae242005-05-28 07:57:14 -04001600
1601 spin_unlock_irq(SCpnt->device->host->host_lock);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001602 return SUCCESS;
1603}
1604
1605/*
1606 * This was borrowed directly from aha1542.c. (Zaga)
1607 */
1608
1609static int wd7000_biosparam(struct scsi_device *sdev,
1610 struct block_device *bdev, sector_t capacity, int *ip)
1611{
1612 char b[BDEVNAME_SIZE];
1613
1614 dprintk("wd7000_biosparam: dev=%s, size=%d, ",
1615 bdevname(bdev, b), capacity);
1616 (void)b; /* unused var warning? */
1617
1618 /*
1619 * try default translation
1620 */
1621 ip[0] = 64;
1622 ip[1] = 32;
1623 ip[2] = capacity >> 11;
1624
1625 /*
1626 * for disks >1GB do some guessing
1627 */
1628 if (ip[2] >= 1024) {
1629 int info[3];
1630
1631 /*
1632 * try to figure out the geometry from the partition table
1633 */
1634 if ((scsicam_bios_param(bdev, capacity, info) < 0) || !(((info[0] == 64) && (info[1] == 32)) || ((info[0] == 255) && (info[1] == 63)))) {
1635 printk("wd7000_biosparam: unable to verify geometry for disk with >1GB.\n" " using extended translation.\n");
1636
1637 ip[0] = 255;
1638 ip[1] = 63;
1639 ip[2] = (unsigned long) capacity / (255 * 63);
1640 } else {
1641 ip[0] = info[0];
1642 ip[1] = info[1];
1643 ip[2] = info[2];
1644
1645 if (info[0] == 255)
Harvey Harrisoncadbd4a2008-07-03 23:47:27 -07001646 printk(KERN_INFO "%s: current partition table is " "using extended translation.\n", __func__);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001647 }
1648 }
1649
1650 dprintk("bios geometry: head=%d, sec=%d, cyl=%d\n", ip[0], ip[1], ip[2]);
1651 dprintk("WARNING: check, if the bios geometry is correct.\n");
1652
1653 return (0);
1654}
1655
1656MODULE_AUTHOR("Thomas Wuensche, John Boyd, Miroslav Zagorac");
1657MODULE_DESCRIPTION("Driver for the WD7000 series ISA controllers");
1658MODULE_LICENSE("GPL");
1659
1660static struct scsi_host_template driver_template = {
1661 .proc_name = "wd7000",
1662 .proc_info = wd7000_proc_info,
1663 .name = "Western Digital WD-7000",
1664 .detect = wd7000_detect,
1665 .release = wd7000_release,
1666 .queuecommand = wd7000_queuecommand,
1667 .eh_host_reset_handler = wd7000_host_reset,
1668 .bios_param = wd7000_biosparam,
1669 .can_queue = WD7000_Q,
1670 .this_id = 7,
1671 .sg_tablesize = WD7000_SG,
1672 .cmd_per_lun = 1,
1673 .unchecked_isa_dma = 1,
1674 .use_clustering = ENABLE_CLUSTERING,
Linus Torvalds1da177e2005-04-16 15:20:36 -07001675};
1676
1677#include "scsi_module.c"