iwlwifi: move some configuration parameters into DVM
There are a number of parameters that aren't really hardware
specific but rather define how the DVM firmware is used.
Move these into the DVM configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
diff --git a/drivers/net/wireless/iwlwifi/dvm/lib.c b/drivers/net/wireless/iwlwifi/dvm/lib.c
index 54f5533..9879550 100644
--- a/drivers/net/wireless/iwlwifi/dvm/lib.c
+++ b/drivers/net/wireless/iwlwifi/dvm/lib.c
@@ -254,23 +254,23 @@
BUILD_BUG_ON(sizeof(iwlagn_def_3w_lookup) !=
sizeof(basic.bt3_lookup_table));
- if (priv->cfg->bt_params) {
+ if (priv->lib->bt_params) {
/*
* newer generation of devices (2000 series and newer)
* use the version 2 of the bt command
* we need to make sure sending the host command
* with correct data structure to avoid uCode assert
*/
- if (priv->cfg->bt_params->bt_session_2) {
+ if (priv->lib->bt_params->bt_session_2) {
bt_cmd_v2.prio_boost = cpu_to_le32(
- priv->cfg->bt_params->bt_prio_boost);
+ priv->lib->bt_params->bt_prio_boost);
bt_cmd_v2.tx_prio_boost = 0;
bt_cmd_v2.rx_prio_boost = 0;
} else {
/* older version only has 8 bits */
- WARN_ON(priv->cfg->bt_params->bt_prio_boost & ~0xFF);
+ WARN_ON(priv->lib->bt_params->bt_prio_boost & ~0xFF);
bt_cmd_v1.prio_boost =
- priv->cfg->bt_params->bt_prio_boost;
+ priv->lib->bt_params->bt_prio_boost;
bt_cmd_v1.tx_prio_boost = 0;
bt_cmd_v1.rx_prio_boost = 0;
}
@@ -330,7 +330,7 @@
priv->bt_full_concurrent ?
"full concurrency" : "3-wire");
- if (priv->cfg->bt_params->bt_session_2) {
+ if (priv->lib->bt_params->bt_session_2) {
memcpy(&bt_cmd_v2.basic, &basic,
sizeof(basic));
ret = iwl_dvm_send_cmd_pdu(priv, REPLY_BT_CONFIG,
@@ -758,8 +758,8 @@
*/
static int iwl_get_active_rx_chain_count(struct iwl_priv *priv)
{
- if (priv->cfg->bt_params &&
- priv->cfg->bt_params->advanced_bt_coexist &&
+ if (priv->lib->bt_params &&
+ priv->lib->bt_params->advanced_bt_coexist &&
(priv->bt_full_concurrent ||
priv->bt_traffic_load >= IWL_BT_COEX_TRAFFIC_LOAD_HIGH)) {
/*
@@ -830,8 +830,8 @@
else
active_chains = priv->nvm_data->valid_rx_ant;
- if (priv->cfg->bt_params &&
- priv->cfg->bt_params->advanced_bt_coexist &&
+ if (priv->lib->bt_params &&
+ priv->lib->bt_params->advanced_bt_coexist &&
(priv->bt_full_concurrent ||
priv->bt_traffic_load >= IWL_BT_COEX_TRAFFIC_LOAD_HIGH)) {
/*