Pull acpica-20060707 into test branch
diff --git a/arch/i386/kernel/ioport.c b/arch/i386/kernel/ioport.c
index 79026f0..498e8bc 100644
--- a/arch/i386/kernel/ioport.c
+++ b/arch/i386/kernel/ioport.c
@@ -79,6 +79,7 @@
 
 		memset(bitmap, 0xff, IO_BITMAP_BYTES);
 		t->io_bitmap_ptr = bitmap;
+		set_thread_flag(TIF_IO_BITMAP);
 	}
 
 	/*
diff --git a/arch/i386/kernel/process.c b/arch/i386/kernel/process.c
index 94e2c87..923bb29 100644
--- a/arch/i386/kernel/process.c
+++ b/arch/i386/kernel/process.c
@@ -359,16 +359,16 @@
  */
 void exit_thread(void)
 {
-	struct task_struct *tsk = current;
-	struct thread_struct *t = &tsk->thread;
-
 	/* The process may have allocated an io port bitmap... nuke it. */
-	if (unlikely(NULL != t->io_bitmap_ptr)) {
+	if (unlikely(test_thread_flag(TIF_IO_BITMAP))) {
+		struct task_struct *tsk = current;
+		struct thread_struct *t = &tsk->thread;
 		int cpu = get_cpu();
 		struct tss_struct *tss = &per_cpu(init_tss, cpu);
 
 		kfree(t->io_bitmap_ptr);
 		t->io_bitmap_ptr = NULL;
+		clear_thread_flag(TIF_IO_BITMAP);
 		/*
 		 * Careful, clear this in the TSS too:
 		 */
@@ -387,6 +387,7 @@
 
 	memset(tsk->thread.debugreg, 0, sizeof(unsigned long)*8);
 	memset(tsk->thread.tls_array, 0, sizeof(tsk->thread.tls_array));	
+	clear_tsk_thread_flag(tsk, TIF_DEBUG);
 	/*
 	 * Forget coprocessor state..
 	 */
@@ -431,7 +432,7 @@
 	savesegment(gs,p->thread.gs);
 
 	tsk = current;
-	if (unlikely(NULL != tsk->thread.io_bitmap_ptr)) {
+	if (unlikely(test_tsk_thread_flag(tsk, TIF_IO_BITMAP))) {
 		p->thread.io_bitmap_ptr = kmalloc(IO_BITMAP_BYTES, GFP_KERNEL);
 		if (!p->thread.io_bitmap_ptr) {
 			p->thread.io_bitmap_max = 0;
@@ -439,6 +440,7 @@
 		}
 		memcpy(p->thread.io_bitmap_ptr, tsk->thread.io_bitmap_ptr,
 			IO_BITMAP_BYTES);
+		set_tsk_thread_flag(p, TIF_IO_BITMAP);
 	}
 
 	/*
@@ -533,10 +535,24 @@
 	return 1;
 }
 
-static inline void
-handle_io_bitmap(struct thread_struct *next, struct tss_struct *tss)
+static noinline void __switch_to_xtra(struct task_struct *next_p,
+				    struct tss_struct *tss)
 {
-	if (!next->io_bitmap_ptr) {
+	struct thread_struct *next;
+
+	next = &next_p->thread;
+
+	if (test_tsk_thread_flag(next_p, TIF_DEBUG)) {
+		set_debugreg(next->debugreg[0], 0);
+		set_debugreg(next->debugreg[1], 1);
+		set_debugreg(next->debugreg[2], 2);
+		set_debugreg(next->debugreg[3], 3);
+		/* no 4 and 5 */
+		set_debugreg(next->debugreg[6], 6);
+		set_debugreg(next->debugreg[7], 7);
+	}
+
+	if (!test_tsk_thread_flag(next_p, TIF_IO_BITMAP)) {
 		/*
 		 * Disable the bitmap via an invalid offset. We still cache
 		 * the previous bitmap owner and the IO bitmap contents:
@@ -544,6 +560,7 @@
 		tss->io_bitmap_base = INVALID_IO_BITMAP_OFFSET;
 		return;
 	}
+
 	if (likely(next == tss->io_bitmap_owner)) {
 		/*
 		 * Previous owner of the bitmap (hence the bitmap content)
@@ -671,20 +688,11 @@
 		set_iopl_mask(next->iopl);
 
 	/*
-	 * Now maybe reload the debug registers
+	 * Now maybe handle debug registers and/or IO bitmaps
 	 */
-	if (unlikely(next->debugreg[7])) {
-		set_debugreg(next->debugreg[0], 0);
-		set_debugreg(next->debugreg[1], 1);
-		set_debugreg(next->debugreg[2], 2);
-		set_debugreg(next->debugreg[3], 3);
-		/* no 4 and 5 */
-		set_debugreg(next->debugreg[6], 6);
-		set_debugreg(next->debugreg[7], 7);
-	}
-
-	if (unlikely(prev->io_bitmap_ptr || next->io_bitmap_ptr))
-		handle_io_bitmap(next, tss);
+	if (unlikely((task_thread_info(next_p)->flags & _TIF_WORK_CTXSW))
+	    || test_tsk_thread_flag(prev_p, TIF_IO_BITMAP))
+		__switch_to_xtra(next_p, tss);
 
 	disable_tsc(prev_p, next_p);
 
diff --git a/arch/i386/kernel/ptrace.c b/arch/i386/kernel/ptrace.c
index fd7eaf7..d3db03f 100644
--- a/arch/i386/kernel/ptrace.c
+++ b/arch/i386/kernel/ptrace.c
@@ -468,8 +468,11 @@
 				  for(i=0; i<4; i++)
 					  if ((0x5f54 >> ((data >> (16 + 4*i)) & 0xf)) & 1)
 						  goto out_tsk;
+				  if (data)
+					  set_tsk_thread_flag(child, TIF_DEBUG);
+				  else
+					  clear_tsk_thread_flag(child, TIF_DEBUG);
 			  }
-
 			  addr -= (long) &dummy->u_debugreg;
 			  addr = addr >> 2;
 			  child->thread.debugreg[addr] = data;
diff --git a/block/blktrace.c b/block/blktrace.c
index 92925e7..b8c07027 100644
--- a/block/blktrace.c
+++ b/block/blktrace.c
@@ -69,7 +69,7 @@
 /*
  * Bio action bits of interest
  */
-static u32 bio_act[3] __read_mostly = { 0, BLK_TC_ACT(BLK_TC_BARRIER), BLK_TC_ACT(BLK_TC_SYNC) };
+static u32 bio_act[5] __read_mostly = { 0, BLK_TC_ACT(BLK_TC_BARRIER), BLK_TC_ACT(BLK_TC_SYNC), 0, BLK_TC_ACT(BLK_TC_AHEAD) };
 
 /*
  * More could be added as needed, taking care to increment the decrementer
@@ -79,6 +79,8 @@
 	(((rw) & (1 << BIO_RW_BARRIER)) >> (BIO_RW_BARRIER - 0))
 #define trace_sync_bit(rw)	\
 	(((rw) & (1 << BIO_RW_SYNC)) >> (BIO_RW_SYNC - 1))
+#define trace_ahead_bit(rw)	\
+	(((rw) & (1 << BIO_RW_AHEAD)) << (BIO_RW_AHEAD - 0))
 
 /*
  * The worker for the various blk_add_trace*() types. Fills out a
@@ -100,6 +102,7 @@
 	what |= ddir_act[rw & WRITE];
 	what |= bio_act[trace_barrier_bit(rw)];
 	what |= bio_act[trace_sync_bit(rw)];
+	what |= bio_act[trace_ahead_bit(rw)];
 
 	pid = tsk->pid;
 	if (unlikely(act_log_check(bt, what, sector, pid)))
diff --git a/block/ll_rw_blk.c b/block/ll_rw_blk.c
index ab17c72..61d6b3c 100644
--- a/block/ll_rw_blk.c
+++ b/block/ll_rw_blk.c
@@ -3491,8 +3491,8 @@
 
 void blk_rq_bio_prep(request_queue_t *q, struct request *rq, struct bio *bio)
 {
-	/* first three bits are identical in rq->flags and bio->bi_rw */
-	rq->flags |= (bio->bi_rw & 7);
+	/* first two bits are identical in rq->flags and bio->bi_rw */
+	rq->flags |= (bio->bi_rw & 3);
 
 	rq->nr_phys_segments = bio_phys_segments(q, bio);
 	rq->nr_hw_segments = bio_hw_segments(q, bio);
diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig
index fef7bab..56c5ba8 100644
--- a/drivers/acpi/Kconfig
+++ b/drivers/acpi/Kconfig
@@ -107,7 +107,6 @@
 config ACPI_VIDEO
 	tristate "Video"
 	depends on X86
-	default y
 	help
 	  This driver implement the ACPI Extensions For Display Adapters
 	  for integrated graphics devices on motherboard, as specified in
@@ -135,8 +134,7 @@
 
 config ACPI_DOCK
 	tristate "Dock"
-	depends on !ACPI_IBM_DOCK
-	default y
+	depends on EXPERIMENTAL
 	help
 	  This driver adds support for ACPI controlled docking stations
 
@@ -214,6 +212,7 @@
 config ACPI_IBM_DOCK
 	bool "Legacy Docking Station Support"
 	depends on ACPI_IBM
+	depends on ACPI_DOCK=n
 	default n
 	---help---
 	  Allows the ibm_acpi driver to handle docking station events.
@@ -357,7 +356,6 @@
 	tristate "Smart Battery System (EXPERIMENTAL)"
 	depends on X86 && I2C
 	depends on EXPERIMENTAL
-	default y
 	help
 	  This driver adds support for the Smart Battery System.
 	  Depends on I2C (Device Drivers ---> I2C support)
diff --git a/drivers/acpi/ac.c b/drivers/acpi/ac.c
index 24ccf81..96309b9 100644
--- a/drivers/acpi/ac.c
+++ b/drivers/acpi/ac.c
@@ -72,7 +72,7 @@
 	unsigned long state;
 };
 
-static struct file_operations acpi_ac_fops = {
+static const struct file_operations acpi_ac_fops = {
 	.open = acpi_ac_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/battery.c b/drivers/acpi/battery.c
index 24bf4dc..6e52217 100644
--- a/drivers/acpi/battery.c
+++ b/drivers/acpi/battery.c
@@ -557,7 +557,7 @@
 	return single_open(file, acpi_battery_read_alarm, PDE(inode)->data);
 }
 
-static struct file_operations acpi_battery_info_ops = {
+static const struct file_operations acpi_battery_info_ops = {
 	.open = acpi_battery_info_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
@@ -565,7 +565,7 @@
 	.owner = THIS_MODULE,
 };
 
-static struct file_operations acpi_battery_state_ops = {
+static const struct file_operations acpi_battery_state_ops = {
 	.open = acpi_battery_state_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
@@ -573,7 +573,7 @@
 	.owner = THIS_MODULE,
 };
 
-static struct file_operations acpi_battery_alarm_ops = {
+static const struct file_operations acpi_battery_alarm_ops = {
 	.open = acpi_battery_alarm_open_fs,
 	.read = seq_read,
 	.write = acpi_battery_write_alarm,
diff --git a/drivers/acpi/bus.c b/drivers/acpi/bus.c
index ea5a049..b297769 100644
--- a/drivers/acpi/bus.c
+++ b/drivers/acpi/bus.c
@@ -192,8 +192,8 @@
 	/* Make sure this is a valid target state */
 
 	if (!device->flags.power_manageable) {
-		printk(KERN_DEBUG "Device `[%s]' is not power manageable",
-				device->kobj.name);
+		ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device `[%s]' is not power manageable",
+				device->kobj.name));
 		return -ENODEV;
 	}
 	/*
diff --git a/drivers/acpi/button.c b/drivers/acpi/button.c
index fd1ba05..5ef885e 100644
--- a/drivers/acpi/button.c
+++ b/drivers/acpi/button.c
@@ -87,14 +87,14 @@
 	unsigned long pushed;
 };
 
-static struct file_operations acpi_button_info_fops = {
+static const struct file_operations acpi_button_info_fops = {
 	.open = acpi_button_info_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
 	.release = single_release,
 };
 
-static struct file_operations acpi_button_state_fops = {
+static const struct file_operations acpi_button_state_fops = {
 	.open = acpi_button_state_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/cm_sbs.c b/drivers/acpi/cm_sbs.c
index 574a75a..a01ce67 100644
--- a/drivers/acpi/cm_sbs.c
+++ b/drivers/acpi/cm_sbs.c
@@ -39,50 +39,43 @@
 static struct proc_dir_entry *acpi_ac_dir;
 static struct proc_dir_entry *acpi_battery_dir;
 
-static struct semaphore cm_sbs_sem;
+static DEFINE_MUTEX(cm_sbs_mutex);
 
-static int lock_ac_dir_cnt = 0;
-static int lock_battery_dir_cnt = 0;
+static int lock_ac_dir_cnt;
+static int lock_battery_dir_cnt;
 
 struct proc_dir_entry *acpi_lock_ac_dir(void)
 {
-
-	down(&cm_sbs_sem);
-	if (!acpi_ac_dir) {
+	mutex_lock(&cm_sbs_mutex);
+	if (!acpi_ac_dir)
 		acpi_ac_dir = proc_mkdir(ACPI_AC_CLASS, acpi_root_dir);
-	}
 	if (acpi_ac_dir) {
 		lock_ac_dir_cnt++;
 	} else {
 		ACPI_DEBUG_PRINT((ACPI_DB_ERROR,
 				  "Cannot create %s\n", ACPI_AC_CLASS));
 	}
-	up(&cm_sbs_sem);
+	mutex_unlock(&cm_sbs_mutex);
 	return acpi_ac_dir;
 }
-
 EXPORT_SYMBOL(acpi_lock_ac_dir);
 
 void acpi_unlock_ac_dir(struct proc_dir_entry *acpi_ac_dir_param)
 {
-
-	down(&cm_sbs_sem);
-	if (acpi_ac_dir_param) {
+	mutex_lock(&cm_sbs_mutex);
+	if (acpi_ac_dir_param)
 		lock_ac_dir_cnt--;
-	}
 	if (lock_ac_dir_cnt == 0 && acpi_ac_dir_param && acpi_ac_dir) {
 		remove_proc_entry(ACPI_AC_CLASS, acpi_root_dir);
 		acpi_ac_dir = 0;
 	}
-	up(&cm_sbs_sem);
+	mutex_unlock(&cm_sbs_mutex);
 }
-
 EXPORT_SYMBOL(acpi_unlock_ac_dir);
 
 struct proc_dir_entry *acpi_lock_battery_dir(void)
 {
-
-	down(&cm_sbs_sem);
+	mutex_lock(&cm_sbs_mutex);
 	if (!acpi_battery_dir) {
 		acpi_battery_dir =
 		    proc_mkdir(ACPI_BATTERY_CLASS, acpi_root_dir);
@@ -93,39 +86,28 @@
 		ACPI_DEBUG_PRINT((ACPI_DB_ERROR,
 				  "Cannot create %s\n", ACPI_BATTERY_CLASS));
 	}
-	up(&cm_sbs_sem);
+	mutex_unlock(&cm_sbs_mutex);
 	return acpi_battery_dir;
 }
-
 EXPORT_SYMBOL(acpi_lock_battery_dir);
 
 void acpi_unlock_battery_dir(struct proc_dir_entry *acpi_battery_dir_param)
 {
-
-	down(&cm_sbs_sem);
-	if (acpi_battery_dir_param) {
+	mutex_lock(&cm_sbs_mutex);
+	if (acpi_battery_dir_param)
 		lock_battery_dir_cnt--;
-	}
 	if (lock_battery_dir_cnt == 0 && acpi_battery_dir_param
 	    && acpi_battery_dir) {
 		remove_proc_entry(ACPI_BATTERY_CLASS, acpi_root_dir);
 		acpi_battery_dir = 0;
 	}
-	up(&cm_sbs_sem);
+	mutex_unlock(&cm_sbs_mutex);
 	return;
 }
-
 EXPORT_SYMBOL(acpi_unlock_battery_dir);
 
 static int __init acpi_cm_sbs_init(void)
 {
-
-	if (acpi_disabled)
-		return 0;
-
-	init_MUTEX(&cm_sbs_sem);
-
 	return 0;
 }
-
 subsys_initcall(acpi_cm_sbs_init);
diff --git a/drivers/acpi/ec.c b/drivers/acpi/ec.c
index 8c5d7df..e5d7963 100644
--- a/drivers/acpi/ec.c
+++ b/drivers/acpi/ec.c
@@ -929,7 +929,7 @@
 	return single_open(file, acpi_ec_read_info, PDE(inode)->data);
 }
 
-static struct file_operations acpi_ec_info_ops = {
+static const struct file_operations acpi_ec_info_ops = {
 	.open = acpi_ec_info_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/event.c b/drivers/acpi/event.c
index a901b23..959a893 100644
--- a/drivers/acpi/event.c
+++ b/drivers/acpi/event.c
@@ -99,7 +99,7 @@
 	return 0;
 }
 
-static struct file_operations acpi_system_event_ops = {
+static const struct file_operations acpi_system_event_ops = {
 	.open = acpi_system_open_event,
 	.read = acpi_system_read_event,
 	.release = acpi_system_close_event,
diff --git a/drivers/acpi/executer/exmutex.c b/drivers/acpi/executer/exmutex.c
index d8ac287..3a39c2e 100644
--- a/drivers/acpi/executer/exmutex.c
+++ b/drivers/acpi/executer/exmutex.c
@@ -267,9 +267,9 @@
 	    && (obj_desc->mutex.os_mutex != ACPI_GLOBAL_LOCK)) {
 		ACPI_ERROR((AE_INFO,
 			    "Thread %X cannot release Mutex [%4.4s] acquired by thread %X",
-			    walk_state->thread->thread_id,
+			    (u32) walk_state->thread->thread_id,
 			    acpi_ut_get_node_name(obj_desc->mutex.node),
-			    obj_desc->mutex.owner_thread->thread_id));
+			    (u32) obj_desc->mutex.owner_thread->thread_id));
 		return_ACPI_STATUS(AE_AML_NOT_OWNER);
 	}
 
diff --git a/drivers/acpi/fan.c b/drivers/acpi/fan.c
index daed246..045c894 100644
--- a/drivers/acpi/fan.c
+++ b/drivers/acpi/fan.c
@@ -120,7 +120,7 @@
 	return count;
 }
 
-static struct file_operations acpi_fan_state_ops = {
+static const struct file_operations acpi_fan_state_ops = {
 	.open = acpi_fan_state_open_fs,
 	.read = seq_read,
 	.write = acpi_fan_write_state,
diff --git a/drivers/acpi/hotkey.c b/drivers/acpi/hotkey.c
index fd81a0f..32c9d88 100644
--- a/drivers/acpi/hotkey.c
+++ b/drivers/acpi/hotkey.c
@@ -184,7 +184,7 @@
 					      *hotkey_list, int event);
 
 /* event based config */
-static struct file_operations hotkey_config_fops = {
+static const struct file_operations hotkey_config_fops = {
 	.open = hotkey_open_config,
 	.read = seq_read,
 	.write = hotkey_write_config,
@@ -193,7 +193,7 @@
 };
 
 /* polling based config */
-static struct file_operations hotkey_poll_config_fops = {
+static const struct file_operations hotkey_poll_config_fops = {
 	.open = hotkey_poll_open_config,
 	.read = seq_read,
 	.write = hotkey_write_config,
@@ -202,7 +202,7 @@
 };
 
 /* hotkey driver info */
-static struct file_operations hotkey_info_fops = {
+static const struct file_operations hotkey_info_fops = {
 	.open = hotkey_info_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
@@ -210,7 +210,7 @@
 };
 
 /* action */
-static struct file_operations hotkey_action_fops = {
+static const struct file_operations hotkey_action_fops = {
 	.open = hotkey_action_open_fs,
 	.read = seq_read,
 	.write = hotkey_execute_aml_method,
@@ -219,7 +219,7 @@
 };
 
 /* polling results */
-static struct file_operations hotkey_polling_fops = {
+static const struct file_operations hotkey_polling_fops = {
 	.open = hotkey_polling_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c
index 5d3447f..fec225d 100644
--- a/drivers/acpi/power.c
+++ b/drivers/acpi/power.c
@@ -80,7 +80,7 @@
 
 static struct list_head acpi_power_resource_list;
 
-static struct file_operations acpi_power_fops = {
+static const struct file_operations acpi_power_fops = {
 	.open = acpi_power_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/processor_core.c b/drivers/acpi/processor_core.c
index 5267432..b13d644 100644
--- a/drivers/acpi/processor_core.c
+++ b/drivers/acpi/processor_core.c
@@ -102,7 +102,7 @@
 #define INSTALL_NOTIFY_HANDLER		1
 #define UNINSTALL_NOTIFY_HANDLER	2
 
-static struct file_operations acpi_processor_info_fops = {
+static const struct file_operations acpi_processor_info_fops = {
 	.open = acpi_processor_info_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c
index 8e9c26a..7106606 100644
--- a/drivers/acpi/processor_idle.c
+++ b/drivers/acpi/processor_idle.c
@@ -1070,7 +1070,7 @@
 			   PDE(inode)->data);
 }
 
-static struct file_operations acpi_processor_power_fops = {
+static const struct file_operations acpi_processor_power_fops = {
 	.open = acpi_processor_power_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
diff --git a/drivers/acpi/sleep/proc.c b/drivers/acpi/sleep/proc.c
index 4696a85..3496257 100644
--- a/drivers/acpi/sleep/proc.c
+++ b/drivers/acpi/sleep/proc.c
@@ -434,7 +434,7 @@
 			   PDE(inode)->data);
 }
 
-static struct file_operations acpi_system_wakeup_device_fops = {
+static const struct file_operations acpi_system_wakeup_device_fops = {
 	.open = acpi_system_wakeup_device_open_fs,
 	.read = seq_read,
 	.write = acpi_system_write_wakeup_device,
@@ -443,7 +443,7 @@
 };
 
 #ifdef	CONFIG_ACPI_SLEEP_PROC_SLEEP
-static struct file_operations acpi_system_sleep_fops = {
+static const struct file_operations acpi_system_sleep_fops = {
 	.open = acpi_system_sleep_open_fs,
 	.read = seq_read,
 	.write = acpi_system_write_sleep,
@@ -452,7 +452,7 @@
 };
 #endif				/* CONFIG_ACPI_SLEEP_PROC_SLEEP */
 
-static struct file_operations acpi_system_alarm_fops = {
+static const struct file_operations acpi_system_alarm_fops = {
 	.open = acpi_system_alarm_open_fs,
 	.read = seq_read,
 	.write = acpi_system_write_alarm,
diff --git a/drivers/acpi/system.c b/drivers/acpi/system.c
index c3bb7faa..d86dcb3 100644
--- a/drivers/acpi/system.c
+++ b/drivers/acpi/system.c
@@ -57,7 +57,7 @@
 	return single_open(file, acpi_system_read_info, PDE(inode)->data);
 }
 
-static struct file_operations acpi_system_info_ops = {
+static const struct file_operations acpi_system_info_ops = {
 	.open = acpi_system_info_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
@@ -67,7 +67,7 @@
 static ssize_t acpi_system_read_dsdt(struct file *, char __user *, size_t,
 				     loff_t *);
 
-static struct file_operations acpi_system_dsdt_ops = {
+static const struct file_operations acpi_system_dsdt_ops = {
 	.read = acpi_system_read_dsdt,
 };
 
@@ -94,7 +94,7 @@
 static ssize_t acpi_system_read_fadt(struct file *, char __user *, size_t,
 				     loff_t *);
 
-static struct file_operations acpi_system_fadt_ops = {
+static const struct file_operations acpi_system_fadt_ops = {
 	.read = acpi_system_read_fadt,
 };
 
diff --git a/drivers/acpi/thermal.c b/drivers/acpi/thermal.c
index 503c0b9..480a317 100644
--- a/drivers/acpi/thermal.c
+++ b/drivers/acpi/thermal.c
@@ -176,21 +176,21 @@
 	struct timer_list timer;
 };
 
-static struct file_operations acpi_thermal_state_fops = {
+static const struct file_operations acpi_thermal_state_fops = {
 	.open = acpi_thermal_state_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
 	.release = single_release,
 };
 
-static struct file_operations acpi_thermal_temp_fops = {
+static const struct file_operations acpi_thermal_temp_fops = {
 	.open = acpi_thermal_temp_open_fs,
 	.read = seq_read,
 	.llseek = seq_lseek,
 	.release = single_release,
 };
 
-static struct file_operations acpi_thermal_trip_fops = {
+static const struct file_operations acpi_thermal_trip_fops = {
 	.open = acpi_thermal_trip_open_fs,
 	.read = seq_read,
 	.write = acpi_thermal_write_trip_points,
@@ -198,7 +198,7 @@
 	.release = single_release,
 };
 
-static struct file_operations acpi_thermal_cooling_fops = {
+static const struct file_operations acpi_thermal_cooling_fops = {
 	.open = acpi_thermal_cooling_open_fs,
 	.read = seq_read,
 	.write = acpi_thermal_write_cooling_mode,
@@ -206,7 +206,7 @@
 	.release = single_release,
 };
 
-static struct file_operations acpi_thermal_polling_fops = {
+static const struct file_operations acpi_thermal_polling_fops = {
 	.open = acpi_thermal_polling_open_fs,
 	.read = seq_read,
 	.write = acpi_thermal_write_polling,
diff --git a/drivers/acpi/utilities/utdebug.c b/drivers/acpi/utilities/utdebug.c
index 5ec1cfc..bb1eaf9 100644
--- a/drivers/acpi/utilities/utdebug.c
+++ b/drivers/acpi/utilities/utdebug.c
@@ -47,7 +47,7 @@
 ACPI_MODULE_NAME("utdebug")
 
 #ifdef ACPI_DEBUG_OUTPUT
-static u32 acpi_gbl_prev_thread_id = 0xFFFFFFFF;
+static acpi_thread_id acpi_gbl_prev_thread_id;
 static char *acpi_gbl_fn_entry_str = "----Entry";
 static char *acpi_gbl_fn_exit_str = "----Exit-";
 
@@ -181,7 +181,7 @@
 		if (ACPI_LV_THREADS & acpi_dbg_level) {
 			acpi_os_printf
 			    ("\n**** Context Switch from TID %X to TID %X ****\n\n",
-			     acpi_gbl_prev_thread_id, thread_id);
+			     (u32) acpi_gbl_prev_thread_id, (u32) thread_id);
 		}
 
 		acpi_gbl_prev_thread_id = thread_id;
diff --git a/drivers/acpi/utilities/utmutex.c b/drivers/acpi/utilities/utmutex.c
index dfc8f30..c39062a 100644
--- a/drivers/acpi/utilities/utmutex.c
+++ b/drivers/acpi/utilities/utmutex.c
@@ -244,14 +244,14 @@
 
 	ACPI_DEBUG_PRINT((ACPI_DB_MUTEX,
 			  "Thread %X attempting to acquire Mutex [%s]\n",
-			  this_thread_id, acpi_ut_get_mutex_name(mutex_id)));
+			  (u32) this_thread_id, acpi_ut_get_mutex_name(mutex_id)));
 
 	status = acpi_os_acquire_mutex(acpi_gbl_mutex_info[mutex_id].mutex,
 				       ACPI_WAIT_FOREVER);
 	if (ACPI_SUCCESS(status)) {
 		ACPI_DEBUG_PRINT((ACPI_DB_MUTEX,
 				  "Thread %X acquired Mutex [%s]\n",
-				  this_thread_id,
+				  (u32) this_thread_id,
 				  acpi_ut_get_mutex_name(mutex_id)));
 
 		acpi_gbl_mutex_info[mutex_id].use_count++;
@@ -259,7 +259,7 @@
 	} else {
 		ACPI_EXCEPTION((AE_INFO, status,
 				"Thread %X could not acquire Mutex [%X]",
-				this_thread_id, mutex_id));
+				(u32) this_thread_id, mutex_id));
 	}
 
 	return (status);
@@ -285,7 +285,7 @@
 
 	this_thread_id = acpi_os_get_thread_id();
 	ACPI_DEBUG_PRINT((ACPI_DB_MUTEX,
-			  "Thread %X releasing Mutex [%s]\n", this_thread_id,
+			  "Thread %X releasing Mutex [%s]\n", (u32) this_thread_id,
 			  acpi_ut_get_mutex_name(mutex_id)));
 
 	if (mutex_id > ACPI_MAX_MUTEX) {
diff --git a/drivers/atm/Kconfig b/drivers/atm/Kconfig
index 01a9f1c..cfa5af8 100644
--- a/drivers/atm/Kconfig
+++ b/drivers/atm/Kconfig
@@ -398,7 +398,7 @@
 	default n
 	help
 	  This defers work to be done by the interrupt handler to a
-	  tasklet instead of hanlding everything at interrupt time.  This
+	  tasklet instead of handling everything at interrupt time.  This
 	  may improve the responsive of the host.
 
 config ATM_FORE200E_TX_RETRY
diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
index 1ba4039..8d32818 100644
--- a/drivers/cpufreq/cpufreq.c
+++ b/drivers/cpufreq/cpufreq.c
@@ -423,6 +423,8 @@
 	if (cpufreq_parse_governor(str_governor, &new_policy.policy, &new_policy.governor))
 		return -EINVAL;
 
+	lock_cpu_hotplug();
+
 	/* Do not use cpufreq_set_policy here or the user_policy.max
 	   will be wrongly overridden */
 	mutex_lock(&policy->lock);
@@ -432,6 +434,8 @@
 	policy->user_policy.governor = policy->governor;
 	mutex_unlock(&policy->lock);
 
+	unlock_cpu_hotplug();
+
 	return ret ? ret : count;
 }
 
diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
index 2819de7..80e8ca0 100644
--- a/drivers/net/3c59x.c
+++ b/drivers/net/3c59x.c
@@ -17,172 +17,6 @@
 	410 Severn Ave., Suite 210
 	Annapolis MD 21403
 
-	Linux Kernel Additions:
-	
- 	0.99H+lk0.9 - David S. Miller - softnet, PCI DMA updates
- 	0.99H+lk1.0 - Jeff Garzik <jgarzik@pobox.com>
-		Remove compatibility defines for kernel versions < 2.2.x.
-		Update for new 2.3.x module interface
-	LK1.1.2 (March 19, 2000)
-	* New PCI interface (jgarzik)
-
-    LK1.1.3 25 April 2000, Andrew Morton <andrewm@uow.edu.au>
-    - Merged with 3c575_cb.c
-    - Don't set RxComplete in boomerang interrupt enable reg
-    - spinlock in vortex_timer to protect mdio functions
-    - disable local interrupts around call to vortex_interrupt in
-      vortex_tx_timeout() (So vortex_interrupt can use spin_lock())
-    - Select window 3 in vortex_timer()'s write to Wn3_MAC_Ctrl
-    - In vortex_start_xmit(), move the lock to _after_ we've altered
-      vp->cur_tx and vp->tx_full.  This defeats the race between
-      vortex_start_xmit() and vortex_interrupt which was identified
-      by Bogdan Costescu.
-    - Merged back support for six new cards from various sources
-    - Set vortex_have_pci if pci_module_init returns zero (fixes cardbus
-      insertion oops)
-    - Tell it that 3c905C has NWAY for 100bT autoneg
-    - Fix handling of SetStatusEnd in 'Too much work..' code, as
-      per 2.3.99's 3c575_cb (Dave Hinds).
-    - Split ISR into two for vortex & boomerang
-    - Fix MOD_INC/DEC races
-    - Handle resource allocation failures.
-    - Fix 3CCFE575CT LED polarity
-    - Make tx_interrupt_mitigation the default
-
-    LK1.1.4 25 April 2000, Andrew Morton <andrewm@uow.edu.au>    
-    - Add extra TxReset to vortex_up() to fix 575_cb hotplug initialisation probs.
-    - Put vortex_info_tbl into __devinitdata
-    - In the vortex_error StatsFull HACK, disable stats in vp->intr_enable as well
-      as in the hardware.
-    - Increased the loop counter in issue_and_wait from 2,000 to 4,000.
-
-    LK1.1.5 28 April 2000, andrewm
-    - Added powerpc defines (John Daniel <jdaniel@etresoft.com> said these work...)
-    - Some extra diagnostics
-    - In vortex_error(), reset the Tx on maxCollisions.  Otherwise most
-      chips usually get a Tx timeout.
-    - Added extra_reset module parm
-    - Replaced some inline timer manip with mod_timer
-      (Franois romieu <Francois.Romieu@nic.fr>)
-    - In vortex_up(), don't make Wn3_config initialisation dependent upon has_nway
-      (this came across from 3c575_cb).
-
-    LK1.1.6 06 Jun 2000, andrewm
-    - Backed out the PPC defines.
-    - Use del_timer_sync(), mod_timer().
-    - Fix wrapped ulong comparison in boomerang_rx()
-    - Add IS_TORNADO, use it to suppress 3c905C checksum error msg
-      (Donald Becker, I Lee Hetherington <ilh@sls.lcs.mit.edu>)
-    - Replace union wn3_config with BFINS/BFEXT manipulation for
-      sparc64 (Pete Zaitcev, Peter Jones)
-    - In vortex_error, do_tx_reset and vortex_tx_timeout(Vortex):
-      do a netif_wake_queue() to better recover from errors. (Anders Pedersen,
-      Donald Becker)
-    - Print a warning on out-of-memory (rate limited to 1 per 10 secs)
-    - Added two more Cardbus 575 NICs: 5b57 and 6564 (Paul Wagland)
-
-    LK1.1.7 2 Jul 2000 andrewm
-    - Better handling of shared IRQs
-    - Reset the transmitter on a Tx reclaim error
-    - Fixed crash under OOM during vortex_open() (Mark Hemment)
-    - Fix Rx cessation problem during OOM (help from Mark Hemment)
-    - The spinlocks around the mdio access were blocking interrupts for 300uS.
-      Fix all this to use spin_lock_bh() within mdio_read/write
-    - Only write to TxFreeThreshold if it's a boomerang - other NICs don't
-      have one.
-    - Added 802.3x MAC-layer flow control support
-
-   LK1.1.8 13 Aug 2000 andrewm
-    - Ignore request_region() return value - already reserved if Cardbus.
-    - Merged some additional Cardbus flags from Don's 0.99Qk
-    - Some fixes for 3c556 (Fred Maciel)
-    - Fix for EISA initialisation (Jan Rekorajski)
-    - Renamed MII_XCVR_PWR and EEPROM_230 to align with 3c575_cb and D. Becker's drivers
-    - Fixed MII_XCVR_PWR for 3CCFE575CT
-    - Added INVERT_LED_PWR, used it.
-    - Backed out the extra_reset stuff
-
-   LK1.1.9 12 Sep 2000 andrewm
-    - Backed out the tx_reset_resume flags.  It was a no-op.
-    - In vortex_error, don't reset the Tx on txReclaim errors
-    - In vortex_error, don't reset the Tx on maxCollisions errors.
-      Hence backed out all the DownListPtr logic here.
-    - In vortex_error, give Tornado cards a partial TxReset on
-      maxCollisions (David Hinds).  Defined MAX_COLLISION_RESET for this.
-    - Redid some driver flags and device names based on pcmcia_cs-3.1.20.
-    - Fixed a bug where, if vp->tx_full is set when the interface
-      is downed, it remains set when the interface is upped.  Bad
-      things happen.
-
-   LK1.1.10 17 Sep 2000 andrewm
-    - Added EEPROM_8BIT for 3c555 (Fred Maciel)
-    - Added experimental support for the 3c556B Laptop Hurricane (Louis Gerbarg)
-    - Add HAS_NWAY to "3c900 Cyclone 10Mbps TPO"
-
-   LK1.1.11 13 Nov 2000 andrewm
-    - Dump MOD_INC/DEC_USE_COUNT, use SET_MODULE_OWNER
-
-   LK1.1.12 1 Jan 2001 andrewm (2.4.0-pre1)
-    - Call pci_enable_device before we request our IRQ (Tobias Ringstrom)
-    - Add 3c590 PCI latency timer hack to vortex_probe1 (from 0.99Ra)
-    - Added extended issue_and_wait for the 3c905CX.
-    - Look for an MII on PHY index 24 first (3c905CX oddity).
-    - Add HAS_NWAY to 3cSOHO100-TX (Brett Frankenberger)
-    - Don't free skbs we don't own on oom path in vortex_open().
-
-   LK1.1.13 27 Jan 2001
-    - Added explicit `medialock' flag so we can truly
-      lock the media type down with `options'.
-    - "check ioremap return and some tidbits" (Arnaldo Carvalho de Melo <acme@conectiva.com.br>)
-    - Added and used EEPROM_NORESET for 3c556B PM resumes.
-    - Fixed leakage of vp->rx_ring.
-    - Break out separate HAS_HWCKSM device capability flag.
-    - Kill vp->tx_full (ANK)
-    - Merge zerocopy fragment handling (ANK?)
-
-   LK1.1.14 15 Feb 2001
-    - Enable WOL.  Can be turned on with `enable_wol' module option.
-    - EISA and PCI initialisation fixes (jgarzik, Manfred Spraul)
-    - If a device's internalconfig register reports it has NWAY,
-      use it, even if autoselect is enabled.
-
-   LK1.1.15 6 June 2001 akpm
-    - Prevent double counting of received bytes (Lars Christensen)
-    - Add ethtool support (jgarzik)
-    - Add module parm descriptions (Andrzej M. Krzysztofowicz)
-    - Implemented alloc_etherdev() API
-    - Special-case the 'Tx error 82' message.
-
-   LK1.1.16 18 July 2001 akpm
-    - Make NETIF_F_SG dependent upon nr_free_highpages(), not on CONFIG_HIGHMEM
-    - Lessen verbosity of bootup messages
-    - Fix WOL - use new PM API functions.
-    - Use netif_running() instead of vp->open in suspend/resume.
-    - Don't reset the interface logic on open/close/rmmod.  It upsets
-      autonegotiation, and hence DHCP (from 0.99T).
-    - Back out EEPROM_NORESET flag because of the above (we do it for all
-      NICs).
-    - Correct 3c982 identification string
-    - Rename wait_for_completion() to issue_and_wait() to avoid completion.h
-      clash.
-
-   LK1.1.17 18Dec01 akpm
-    - PCI ID 9805 is a Python-T, not a dual-port Cyclone.  Apparently.
-      And it has NWAY.
-    - Mask our advertised modes (vp->advertising) with our capabilities
-	  (MII reg5) when deciding which duplex mode to use.
-    - Add `global_options' as default for options[].  Ditto global_enable_wol,
-      global_full_duplex.
-
-   LK1.1.18 01Jul02 akpm
-    - Fix for undocumented transceiver power-up bit on some 3c566B's
-      (Donald Becker, Rahul Karnik)
-
-    - See http://www.zip.com.au/~akpm/linux/#3c59x-2.3 for more details.
-    - Also see Documentation/networking/vortex.txt
-
-   LK1.1.19 10Nov02 Marc Zyngier <maz@wild-wind.fr.eu.org>
-    - EISA sysfs integration.
 */
 
 /*
diff --git a/drivers/net/8139too.c b/drivers/net/8139too.c
index cd97185..e4f4eaf 100644
--- a/drivers/net/8139too.c
+++ b/drivers/net/8139too.c
@@ -1709,6 +1709,7 @@
 	void __iomem *ioaddr = tp->mmio_addr;
 	unsigned int entry;
 	unsigned int len = skb->len;
+	unsigned long flags;
 
 	/* Calculate the next Tx descriptor entry. */
 	entry = tp->cur_tx % NUM_TX_DESC;
@@ -1725,7 +1726,7 @@
 		return 0;
 	}
 
-	spin_lock_irq(&tp->lock);
+	spin_lock_irqsave(&tp->lock, flags);
 	RTL_W32_F (TxStatus0 + (entry * sizeof (u32)),
 		   tp->tx_flag | max(len, (unsigned int)ETH_ZLEN));
 
@@ -1736,7 +1737,7 @@
 
 	if ((tp->cur_tx - NUM_TX_DESC) == tp->dirty_tx)
 		netif_stop_queue (dev);
-	spin_unlock_irq(&tp->lock);
+	spin_unlock_irqrestore(&tp->lock, flags);
 
 	if (netif_msg_tx_queued(tp))
 		printk (KERN_DEBUG "%s: Queued Tx packet size %u to slot %d.\n",
diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index 64b6a72..db73de0 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -1639,7 +1639,7 @@
 		skb = tx_buf->skb;
 #ifdef BCM_TSO 
 		/* partial BD completions possible with TSO packets */
-		if (skb_shinfo(skb)->gso_size) {
+		if (skb_is_gso(skb)) {
 			u16 last_idx, last_ring_idx;
 
 			last_idx = sw_cons +
diff --git a/drivers/net/chelsio/sge.c b/drivers/net/chelsio/sge.c
index 87f94d9..61b3754 100644
--- a/drivers/net/chelsio/sge.c
+++ b/drivers/net/chelsio/sge.c
@@ -1417,7 +1417,7 @@
 	struct cpl_tx_pkt *cpl;
 
 #ifdef NETIF_F_TSO
-	if (skb_shinfo(skb)->gso_size) {
+	if (skb_is_gso(skb)) {
 		int eth_type;
 		struct cpl_tx_pkt_lso *hdr;
 
diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h
index 3042d33..f411bbb 100644
--- a/drivers/net/e1000/e1000.h
+++ b/drivers/net/e1000/e1000.h
@@ -68,7 +68,6 @@
 #ifdef NETIF_F_TSO
 #include <net/checksum.h>
 #endif
-#include <linux/workqueue.h>
 #include <linux/mii.h>
 #include <linux/ethtool.h>
 #include <linux/if_vlan.h>
@@ -143,6 +142,7 @@
 
 #define AUTO_ALL_MODES            0
 #define E1000_EEPROM_82544_APM    0x0004
+#define E1000_EEPROM_ICH8_APME    0x0004
 #define E1000_EEPROM_APME         0x0400
 
 #ifndef E1000_MASTER_SLAVE
@@ -254,7 +254,6 @@
 	spinlock_t tx_queue_lock;
 #endif
 	atomic_t irq_sem;
-	struct work_struct watchdog_task;
 	struct work_struct reset_task;
 	uint8_t fc_autoneg;
 
@@ -339,8 +338,14 @@
 #ifdef NETIF_F_TSO
 	boolean_t tso_force;
 #endif
+	boolean_t smart_power_down;	/* phy smart power down */
+	unsigned long flags;
 };
 
+enum e1000_state_t {
+	__E1000_DRIVER_TESTING,
+	__E1000_RESETTING,
+};
 
 /*  e1000_main.c  */
 extern char e1000_driver_name[];
@@ -348,6 +353,7 @@
 int e1000_up(struct e1000_adapter *adapter);
 void e1000_down(struct e1000_adapter *adapter);
 void e1000_reset(struct e1000_adapter *adapter);
+void e1000_reinit_locked(struct e1000_adapter *adapter);
 int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
 void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
 int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c
index d196648..88a82ba 100644
--- a/drivers/net/e1000/e1000_ethtool.c
+++ b/drivers/net/e1000/e1000_ethtool.c
@@ -109,7 +109,8 @@
 		                   SUPPORTED_1000baseT_Full|
 		                   SUPPORTED_Autoneg |
 		                   SUPPORTED_TP);
-
+		if (hw->phy_type == e1000_phy_ife)
+			ecmd->supported &= ~SUPPORTED_1000baseT_Full;
 		ecmd->advertising = ADVERTISED_TP;
 
 		if (hw->autoneg == 1) {
@@ -203,11 +204,9 @@
 
 	/* reset the link */
 
-	if (netif_running(adapter->netdev)) {
-		e1000_down(adapter);
-		e1000_reset(adapter);
-		e1000_up(adapter);
-	} else
+	if (netif_running(adapter->netdev))
+		e1000_reinit_locked(adapter);
+	else
 		e1000_reset(adapter);
 
 	return 0;
@@ -254,10 +253,9 @@
 	hw->original_fc = hw->fc;
 
 	if (adapter->fc_autoneg == AUTONEG_ENABLE) {
-		if (netif_running(adapter->netdev)) {
-			e1000_down(adapter);
-			e1000_up(adapter);
-		} else
+		if (netif_running(adapter->netdev))
+			e1000_reinit_locked(adapter);
+		else
 			e1000_reset(adapter);
 	} else
 		return ((hw->media_type == e1000_media_type_fiber) ?
@@ -279,10 +277,9 @@
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	adapter->rx_csum = data;
 
-	if (netif_running(netdev)) {
-		e1000_down(adapter);
-		e1000_up(adapter);
-	} else
+	if (netif_running(netdev))
+		e1000_reinit_locked(adapter);
+	else
 		e1000_reset(adapter);
 	return 0;
 }
@@ -577,6 +574,7 @@
 	case e1000_82572:
 	case e1000_82573:
 	case e1000_80003es2lan:
+	case e1000_ich8lan:
 		sprintf(firmware_version, "%d.%d-%d",
 			(eeprom_data & 0xF000) >> 12,
 			(eeprom_data & 0x0FF0) >> 4,
@@ -631,6 +629,9 @@
 	tx_ring_size = sizeof(struct e1000_tx_ring) * adapter->num_tx_queues;
 	rx_ring_size = sizeof(struct e1000_rx_ring) * adapter->num_rx_queues;
 
+	while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+		msleep(1);
+
 	if (netif_running(adapter->netdev))
 		e1000_down(adapter);
 
@@ -691,9 +692,11 @@
 		adapter->rx_ring = rx_new;
 		adapter->tx_ring = tx_new;
 		if ((err = e1000_up(adapter)))
-			return err;
+			goto err_setup;
 	}
 
+	clear_bit(__E1000_RESETTING, &adapter->flags);
+
 	return 0;
 err_setup_tx:
 	e1000_free_all_rx_resources(adapter);
@@ -701,6 +704,8 @@
 	adapter->rx_ring = rx_old;
 	adapter->tx_ring = tx_old;
 	e1000_up(adapter);
+err_setup:
+	clear_bit(__E1000_RESETTING, &adapter->flags);
 	return err;
 }
 
@@ -754,6 +759,7 @@
 		toggle = 0x7FFFF3FF;
 		break;
 	case e1000_82573:
+	case e1000_ich8lan:
 		toggle = 0x7FFFF033;
 		break;
 	default:
@@ -773,11 +779,12 @@
 	}
 	/* restore previous status */
 	E1000_WRITE_REG(&adapter->hw, STATUS, before);
-
-	REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
-	REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF);
-	REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF);
-	REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF);
+	if (adapter->hw.mac_type != e1000_ich8lan) {
+		REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
+		REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF);
+		REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF);
+		REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF);
+	}
 	REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF);
 	REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
 	REG_PATTERN_TEST(RDLEN, 0x000FFF80, 0x000FFFFF);
@@ -790,20 +797,22 @@
 	REG_PATTERN_TEST(TDLEN, 0x000FFF80, 0x000FFFFF);
 
 	REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000);
-	REG_SET_AND_CHECK(RCTL, 0x06DFB3FE, 0x003FFFFB);
+	before = (adapter->hw.mac_type == e1000_ich8lan ?
+			0x06C3B33E : 0x06DFB3FE);
+	REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB);
 	REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000);
 
 	if (adapter->hw.mac_type >= e1000_82543) {
 
-		REG_SET_AND_CHECK(RCTL, 0x06DFB3FE, 0xFFFFFFFF);
+		REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF);
 		REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
-		REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
+		if (adapter->hw.mac_type != e1000_ich8lan)
+			REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
 		REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
 		REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF);
-
-		for (i = 0; i < E1000_RAR_ENTRIES; i++) {
-			REG_PATTERN_TEST(RA + ((i << 1) << 2), 0xFFFFFFFF,
-					 0xFFFFFFFF);
+		value = (adapter->hw.mac_type == e1000_ich8lan ?
+				E1000_RAR_ENTRIES_ICH8LAN : E1000_RAR_ENTRIES);
+		for (i = 0; i < value; i++) {
 			REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF,
 					 0xFFFFFFFF);
 		}
@@ -817,7 +826,9 @@
 
 	}
 
-	for (i = 0; i < E1000_MC_TBL_SIZE; i++)
+	value = (adapter->hw.mac_type == e1000_ich8lan ?
+			E1000_MC_TBL_SIZE_ICH8LAN : E1000_MC_TBL_SIZE);
+	for (i = 0; i < value; i++)
 		REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF);
 
 	*data = 0;
@@ -889,6 +900,8 @@
 	/* Test each interrupt */
 	for (; i < 10; i++) {
 
+		if (adapter->hw.mac_type == e1000_ich8lan && i == 8)
+			continue;
 		/* Interrupt to test */
 		mask = 1 << i;
 
@@ -1246,18 +1259,33 @@
 	} else if (adapter->hw.phy_type == e1000_phy_gg82563) {
 		e1000_write_phy_reg(&adapter->hw,
 		                    GG82563_PHY_KMRN_MODE_CTRL,
-		                    0x1CE);
+		                    0x1CC);
 	}
-	/* force 1000, set loopback */
-	e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x4140);
 
-	/* Now set up the MAC to the same speed/duplex as the PHY. */
 	ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL);
-	ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
-	ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
-		     E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
-		     E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
-		     E1000_CTRL_FD);	 /* Force Duplex to FULL */
+
+	if (adapter->hw.phy_type == e1000_phy_ife) {
+		/* force 100, set loopback */
+		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x6100);
+
+		/* Now set up the MAC to the same speed/duplex as the PHY. */
+		ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+		ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+			     E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+			     E1000_CTRL_SPD_100 |/* Force Speed to 100 */
+			     E1000_CTRL_FD);	 /* Force Duplex to FULL */
+	} else {
+		/* force 1000, set loopback */
+		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x4140);
+
+		/* Now set up the MAC to the same speed/duplex as the PHY. */
+		ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL);
+		ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+		ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+			     E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+			     E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
+			     E1000_CTRL_FD);	 /* Force Duplex to FULL */
+	}
 
 	if (adapter->hw.media_type == e1000_media_type_copper &&
 	   adapter->hw.phy_type == e1000_phy_m88) {
@@ -1317,6 +1345,7 @@
 	case e1000_82572:
 	case e1000_82573:
 	case e1000_80003es2lan:
+	case e1000_ich8lan:
 		return e1000_integrated_phy_loopback(adapter);
 		break;
 
@@ -1568,6 +1597,7 @@
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	boolean_t if_running = netif_running(netdev);
 
+	set_bit(__E1000_DRIVER_TESTING, &adapter->flags);
 	if (eth_test->flags == ETH_TEST_FL_OFFLINE) {
 		/* Offline tests */
 
@@ -1582,7 +1612,8 @@
 			eth_test->flags |= ETH_TEST_FL_FAILED;
 
 		if (if_running)
-			e1000_down(adapter);
+			/* indicate we're in test mode */
+			dev_close(netdev);
 		else
 			e1000_reset(adapter);
 
@@ -1607,8 +1638,9 @@
 		adapter->hw.autoneg = autoneg;
 
 		e1000_reset(adapter);
+		clear_bit(__E1000_DRIVER_TESTING, &adapter->flags);
 		if (if_running)
-			e1000_up(adapter);
+			dev_open(netdev);
 	} else {
 		/* Online tests */
 		if (e1000_link_test(adapter, &data[4]))
@@ -1619,6 +1651,8 @@
 		data[1] = 0;
 		data[2] = 0;
 		data[3] = 0;
+
+		clear_bit(__E1000_DRIVER_TESTING, &adapter->flags);
 	}
 	msleep_interruptible(4 * 1000);
 }
@@ -1778,21 +1812,18 @@
 		mod_timer(&adapter->blink_timer, jiffies);
 		msleep_interruptible(data * 1000);
 		del_timer_sync(&adapter->blink_timer);
-	} else if (adapter->hw.mac_type < e1000_82573) {
-		E1000_WRITE_REG(&adapter->hw, LEDCTL,
-			(E1000_LEDCTL_LED2_BLINK_RATE |
-			 E1000_LEDCTL_LED0_BLINK | E1000_LEDCTL_LED2_BLINK |
-			 (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED2_MODE_SHIFT) |
-			 (E1000_LEDCTL_MODE_LINK_ACTIVITY << E1000_LEDCTL_LED0_MODE_SHIFT) |
-			 (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED1_MODE_SHIFT)));
+	} else if (adapter->hw.phy_type == e1000_phy_ife) {
+		if (!adapter->blink_timer.function) {
+			init_timer(&adapter->blink_timer);
+			adapter->blink_timer.function = e1000_led_blink_callback;
+			adapter->blink_timer.data = (unsigned long) adapter;
+		}
+		mod_timer(&adapter->blink_timer, jiffies);
 		msleep_interruptible(data * 1000);
+		del_timer_sync(&adapter->blink_timer);
+		e1000_write_phy_reg(&(adapter->hw), IFE_PHY_SPECIAL_CONTROL_LED, 0);
 	} else {
-		E1000_WRITE_REG(&adapter->hw, LEDCTL,
-			(E1000_LEDCTL_LED2_BLINK_RATE |
-			 E1000_LEDCTL_LED1_BLINK | E1000_LEDCTL_LED2_BLINK |
-			 (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED2_MODE_SHIFT) |
-			 (E1000_LEDCTL_MODE_LINK_ACTIVITY << E1000_LEDCTL_LED1_MODE_SHIFT) |
-			 (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED0_MODE_SHIFT)));
+		e1000_blink_led_start(&adapter->hw);
 		msleep_interruptible(data * 1000);
 	}
 
@@ -1807,10 +1838,8 @@
 e1000_nway_reset(struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
-	if (netif_running(netdev)) {
-		e1000_down(adapter);
-		e1000_up(adapter);
-	}
+	if (netif_running(netdev))
+		e1000_reinit_locked(adapter);
 	return 0;
 }
 
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index 3959039..583518a 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -101,7 +101,8 @@
 
 #define E1000_WRITE_REG_IO(a, reg, val) \
 	    e1000_write_reg_io((a), E1000_##reg, val)
-static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw);
+static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw,
+                                               uint16_t duplex);
 static int32_t e1000_configure_kmrn_for_1000(struct e1000_hw *hw);
 
 /* IGP cable length table */
@@ -156,6 +157,14 @@
             hw->phy_type = e1000_phy_igp;
             break;
         }
+    case IGP03E1000_E_PHY_ID:
+        hw->phy_type = e1000_phy_igp_3;
+        break;
+    case IFE_E_PHY_ID:
+    case IFE_PLUS_E_PHY_ID:
+    case IFE_C_E_PHY_ID:
+        hw->phy_type = e1000_phy_ife;
+        break;
     case GG82563_E_PHY_ID:
         if (hw->mac_type == e1000_80003es2lan) {
             hw->phy_type = e1000_phy_gg82563;
@@ -332,6 +341,7 @@
         break;
     case E1000_DEV_ID_82541EI:
     case E1000_DEV_ID_82541EI_MOBILE:
+    case E1000_DEV_ID_82541ER_LOM:
         hw->mac_type = e1000_82541;
         break;
     case E1000_DEV_ID_82541ER:
@@ -341,6 +351,7 @@
         hw->mac_type = e1000_82541_rev_2;
         break;
     case E1000_DEV_ID_82547EI:
+    case E1000_DEV_ID_82547EI_MOBILE:
         hw->mac_type = e1000_82547;
         break;
     case E1000_DEV_ID_82547GI:
@@ -354,6 +365,7 @@
     case E1000_DEV_ID_82572EI_COPPER:
     case E1000_DEV_ID_82572EI_FIBER:
     case E1000_DEV_ID_82572EI_SERDES:
+    case E1000_DEV_ID_82572EI:
         hw->mac_type = e1000_82572;
         break;
     case E1000_DEV_ID_82573E:
@@ -361,16 +373,29 @@
     case E1000_DEV_ID_82573L:
         hw->mac_type = e1000_82573;
         break;
+    case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
+    case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
     case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
     case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
         hw->mac_type = e1000_80003es2lan;
         break;
+    case E1000_DEV_ID_ICH8_IGP_M_AMT:
+    case E1000_DEV_ID_ICH8_IGP_AMT:
+    case E1000_DEV_ID_ICH8_IGP_C:
+    case E1000_DEV_ID_ICH8_IFE:
+    case E1000_DEV_ID_ICH8_IGP_M:
+        hw->mac_type = e1000_ich8lan;
+        break;
     default:
         /* Should never have loaded on this device */
         return -E1000_ERR_MAC_TYPE;
     }
 
     switch(hw->mac_type) {
+    case e1000_ich8lan:
+        hw->swfwhw_semaphore_present = TRUE;
+        hw->asf_firmware_present = TRUE;
+        break;
     case e1000_80003es2lan:
         hw->swfw_sync_present = TRUE;
         /* fall through */
@@ -423,6 +448,7 @@
         case e1000_82542_rev2_1:
             hw->media_type = e1000_media_type_fiber;
             break;
+        case e1000_ich8lan:
         case e1000_82573:
             /* The STATUS_TBIMODE bit is reserved or reused for the this
              * device.
@@ -527,6 +553,14 @@
         } while(timeout);
     }
 
+    /* Workaround for ICH8 bit corruption issue in FIFO memory */
+    if (hw->mac_type == e1000_ich8lan) {
+        /* Set Tx and Rx buffer allocation to 8k apiece. */
+        E1000_WRITE_REG(hw, PBA, E1000_PBA_8K);
+        /* Set Packet Buffer Size to 16k. */
+        E1000_WRITE_REG(hw, PBS, E1000_PBS_16K);
+    }
+
     /* Issue a global reset to the MAC.  This will reset the chip's
      * transmit, receive, DMA, and link units.  It will not effect
      * the current PCI configuration.  The global reset bit is self-
@@ -550,6 +584,20 @@
             /* Reset is performed on a shadow of the control register */
             E1000_WRITE_REG(hw, CTRL_DUP, (ctrl | E1000_CTRL_RST));
             break;
+        case e1000_ich8lan:
+            if (!hw->phy_reset_disable &&
+                e1000_check_phy_reset_block(hw) == E1000_SUCCESS) {
+                /* e1000_ich8lan PHY HW reset requires MAC CORE reset
+                 * at the same time to make sure the interface between
+                 * MAC and the external PHY is reset.
+                 */
+                ctrl |= E1000_CTRL_PHY_RST;
+            }
+
+            e1000_get_software_flag(hw);
+            E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
+            msec_delay(5);
+            break;
         default:
             E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
             break;
@@ -591,6 +639,7 @@
             /* fall through */
         case e1000_82571:
         case e1000_82572:
+        case e1000_ich8lan:
         case e1000_80003es2lan:
             ret_val = e1000_get_auto_rd_done(hw);
             if(ret_val)
@@ -633,6 +682,12 @@
             e1000_pci_set_mwi(hw);
     }
 
+    if (hw->mac_type == e1000_ich8lan) {
+        uint32_t kab = E1000_READ_REG(hw, KABGTXD);
+        kab |= E1000_KABGTXD_BGSQLBIAS;
+        E1000_WRITE_REG(hw, KABGTXD, kab);
+    }
+
     return E1000_SUCCESS;
 }
 
@@ -675,9 +730,12 @@
 
     /* Disabling VLAN filtering. */
     DEBUGOUT("Initializing the IEEE VLAN\n");
-    if (hw->mac_type < e1000_82545_rev_3)
-        E1000_WRITE_REG(hw, VET, 0);
-    e1000_clear_vfta(hw);
+    /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
+    if (hw->mac_type != e1000_ich8lan) {
+        if (hw->mac_type < e1000_82545_rev_3)
+            E1000_WRITE_REG(hw, VET, 0);
+        e1000_clear_vfta(hw);
+    }
 
     /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
     if(hw->mac_type == e1000_82542_rev2_0) {
@@ -705,8 +763,14 @@
     /* Zero out the Multicast HASH table */
     DEBUGOUT("Zeroing the MTA\n");
     mta_size = E1000_MC_TBL_SIZE;
-    for(i = 0; i < mta_size; i++)
+    if (hw->mac_type == e1000_ich8lan)
+        mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
+    for(i = 0; i < mta_size; i++) {
         E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+        /* use write flush to prevent Memory Write Block (MWB) from
+         * occuring when accessing our register space */
+        E1000_WRITE_FLUSH(hw);
+    }
 
     /* Set the PCI priority bit correctly in the CTRL register.  This
      * determines if the adapter gives priority to receives, or if it
@@ -744,6 +808,10 @@
         break;
     }
 
+    /* More time needed for PHY to initialize */
+    if (hw->mac_type == e1000_ich8lan)
+        msec_delay(15);
+
     /* Call a subroutine to configure the link and setup flow control. */
     ret_val = e1000_setup_link(hw);
 
@@ -757,6 +825,7 @@
         case e1000_82571:
         case e1000_82572:
         case e1000_82573:
+        case e1000_ich8lan:
         case e1000_80003es2lan:
             ctrl |= E1000_TXDCTL_COUNT_DESC;
             break;
@@ -795,6 +864,7 @@
         /* Fall through */
     case e1000_82571:
     case e1000_82572:
+    case e1000_ich8lan:
         ctrl = E1000_READ_REG(hw, TXDCTL1);
         ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
         if(hw->mac_type >= e1000_82571)
@@ -818,6 +888,11 @@
      */
     e1000_clear_hw_cntrs(hw);
 
+    /* ICH8 No-snoop bits are opposite polarity.
+     * Set to snoop by default after reset. */
+    if (hw->mac_type == e1000_ich8lan)
+        e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL);
+
     if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
         hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
         ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
@@ -905,6 +980,7 @@
      */
     if (hw->fc == e1000_fc_default) {
         switch (hw->mac_type) {
+        case e1000_ich8lan:
         case e1000_82573:
             hw->fc = e1000_fc_full;
             break;
@@ -971,9 +1047,12 @@
      */
     DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
 
-    E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
-    E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
-    E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+    /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
+    if (hw->mac_type != e1000_ich8lan) {
+        E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+        E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+        E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
+    }
 
     E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
 
@@ -1237,12 +1316,13 @@
 
     /* Wait 10ms for MAC to configure PHY from eeprom settings */
     msec_delay(15);
-
+    if (hw->mac_type != e1000_ich8lan) {
     /* Configure activity LED after PHY reset */
     led_ctrl = E1000_READ_REG(hw, LEDCTL);
     led_ctrl &= IGP_ACTIVITY_LED_MASK;
     led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
     E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
+    }
 
     /* disable lplu d3 during driver init */
     ret_val = e1000_set_d3_lplu_state(hw, FALSE);
@@ -1478,8 +1558,7 @@
             if (ret_val)
                 return ret_val;
 
-            /* Enable Pass False Carrier on the PHY */
-            phy_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+            phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
 
             ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
                                           phy_data);
@@ -1561,28 +1640,40 @@
     phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
     if(hw->disable_polarity_correction == 1)
         phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
-        ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
-        if(ret_val)
-            return ret_val;
-
-    /* Force TX_CLK in the Extended PHY Specific Control Register
-     * to 25MHz clock.
-     */
-    ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
-    if(ret_val)
+    ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+    if (ret_val)
         return ret_val;
 
-    phy_data |= M88E1000_EPSCR_TX_CLK_25;
-
     if (hw->phy_revision < M88E1011_I_REV_4) {
-        /* Configure Master and Slave downshift values */
-        phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
-                              M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
-        phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
-                             M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
-        ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
-        if(ret_val)
+        /* Force TX_CLK in the Extended PHY Specific Control Register
+         * to 25MHz clock.
+         */
+        ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+        if (ret_val)
             return ret_val;
+
+        phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+        if ((hw->phy_revision == E1000_REVISION_2) &&
+            (hw->phy_id == M88E1111_I_PHY_ID)) {
+            /* Vidalia Phy, set the downshift counter to 5x */
+            phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
+            phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+            ret_val = e1000_write_phy_reg(hw,
+                                        M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+            if (ret_val)
+                return ret_val;
+        } else {
+            /* Configure Master and Slave downshift values */
+            phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+                              M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+            phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+                             M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+            ret_val = e1000_write_phy_reg(hw,
+                                        M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+            if (ret_val)
+               return ret_val;
+        }
     }
 
     /* SW Reset the PHY so all changes take effect */
@@ -1620,6 +1711,10 @@
     if(hw->autoneg_advertised == 0)
         hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
 
+    /* IFE phy only supports 10/100 */
+    if (hw->phy_type == e1000_phy_ife)
+        hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
+
     DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
     ret_val = e1000_phy_setup_autoneg(hw);
     if(ret_val) {
@@ -1717,6 +1812,26 @@
 
     DEBUGFUNC("e1000_setup_copper_link");
 
+    switch (hw->mac_type) {
+    case e1000_80003es2lan:
+    case e1000_ich8lan:
+        /* Set the mac to wait the maximum time between each
+         * iteration and increase the max iterations when
+         * polling the phy; this fixes erroneous timeouts at 10Mbps. */
+        ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
+        if (ret_val)
+            return ret_val;
+        ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), &reg_data);
+        if (ret_val)
+            return ret_val;
+        reg_data |= 0x3F;
+        ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
+        if (ret_val)
+            return ret_val;
+    default:
+        break;
+    }
+
     /* Check if it is a valid PHY and set PHY mode if necessary. */
     ret_val = e1000_copper_link_preconfig(hw);
     if(ret_val)
@@ -1724,10 +1839,8 @@
 
     switch (hw->mac_type) {
     case e1000_80003es2lan:
-        ret_val = e1000_read_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
-                                      &reg_data);
-        if (ret_val)
-            return ret_val;
+        /* Kumeran registers are written-only */
+        reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
         reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
         ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
                                        reg_data);
@@ -1739,6 +1852,7 @@
     }
 
     if (hw->phy_type == e1000_phy_igp ||
+        hw->phy_type == e1000_phy_igp_3 ||
         hw->phy_type == e1000_phy_igp_2) {
         ret_val = e1000_copper_link_igp_setup(hw);
         if(ret_val)
@@ -1803,7 +1917,7 @@
 * hw - Struct containing variables accessed by shared code
 ******************************************************************************/
 static int32_t
-e1000_configure_kmrn_for_10_100(struct e1000_hw *hw)
+e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex)
 {
     int32_t ret_val = E1000_SUCCESS;
     uint32_t tipg;
@@ -1823,6 +1937,18 @@
     tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
     E1000_WRITE_REG(hw, TIPG, tipg);
 
+    ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+
+    if (ret_val)
+        return ret_val;
+
+    if (duplex == HALF_DUPLEX)
+        reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+    else
+        reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+    ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
     return ret_val;
 }
 
@@ -1847,6 +1973,14 @@
     tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
     E1000_WRITE_REG(hw, TIPG, tipg);
 
+    ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+
+    if (ret_val)
+        return ret_val;
+
+    reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+    ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
     return ret_val;
 }
 
@@ -1869,10 +2003,13 @@
     if(ret_val)
         return ret_val;
 
-    /* Read the MII 1000Base-T Control Register (Address 9). */
-    ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
-    if(ret_val)
-        return ret_val;
+    if (hw->phy_type != e1000_phy_ife) {
+        /* Read the MII 1000Base-T Control Register (Address 9). */
+        ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+        if (ret_val)
+            return ret_val;
+    } else
+        mii_1000t_ctrl_reg=0;
 
     /* Need to parse both autoneg_advertised and fc and set up
      * the appropriate PHY registers.  First we will parse for
@@ -1923,6 +2060,9 @@
     if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
         DEBUGOUT("Advertise 1000mb Full duplex\n");
         mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+        if (hw->phy_type == e1000_phy_ife) {
+            DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n");
+        }
     }
 
     /* Check for a software override of the flow control settings, and
@@ -1984,9 +2124,11 @@
 
     DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
 
-    ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
-    if(ret_val)
-        return ret_val;
+    if (hw->phy_type != e1000_phy_ife) {
+        ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+        if (ret_val)
+            return ret_val;
+    }
 
     return E1000_SUCCESS;
 }
@@ -2089,6 +2231,18 @@
 
         /* Need to reset the PHY or these changes will be ignored */
         mii_ctrl_reg |= MII_CR_RESET;
+    /* Disable MDI-X support for 10/100 */
+    } else if (hw->phy_type == e1000_phy_ife) {
+        ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
+        if (ret_val)
+            return ret_val;
+
+        phy_data &= ~IFE_PMC_AUTO_MDIX;
+        phy_data &= ~IFE_PMC_FORCE_MDIX;
+
+        ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data);
+        if (ret_val)
+            return ret_val;
     } else {
         /* Clear Auto-Crossover to force MDI manually.  IGP requires MDI
          * forced whenever speed or duplex are forced.
@@ -2721,8 +2875,12 @@
          */
         if(hw->tbi_compatibility_en) {
             uint16_t speed, duplex;
-            e1000_get_speed_and_duplex(hw, &speed, &duplex);
-            if(speed != SPEED_1000) {
+            ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
+            if (ret_val) {
+                DEBUGOUT("Error getting link speed and duplex\n");
+                return ret_val;
+            }
+            if (speed != SPEED_1000) {
                 /* If link speed is not set to gigabit speed, we do not need
                  * to enable TBI compatibility.
                  */
@@ -2889,7 +3047,13 @@
         if (*speed == SPEED_1000)
             ret_val = e1000_configure_kmrn_for_1000(hw);
         else
-            ret_val = e1000_configure_kmrn_for_10_100(hw);
+            ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex);
+        if (ret_val)
+            return ret_val;
+    }
+
+    if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) {
+        ret_val = e1000_kumeran_lock_loss_workaround(hw);
         if (ret_val)
             return ret_val;
     }
@@ -3079,6 +3243,9 @@
 
     DEBUGFUNC("e1000_swfw_sync_acquire");
 
+    if (hw->swfwhw_semaphore_present)
+        return e1000_get_software_flag(hw);
+
     if (!hw->swfw_sync_present)
         return e1000_get_hw_eeprom_semaphore(hw);
 
@@ -3118,6 +3285,11 @@
 
     DEBUGFUNC("e1000_swfw_sync_release");
 
+    if (hw->swfwhw_semaphore_present) {
+        e1000_release_software_flag(hw);
+        return;
+    }
+
     if (!hw->swfw_sync_present) {
         e1000_put_hw_eeprom_semaphore(hw);
         return;
@@ -3160,7 +3332,8 @@
     if (e1000_swfw_sync_acquire(hw, swfw))
         return -E1000_ERR_SWFW_SYNC;
 
-    if((hw->phy_type == e1000_phy_igp ||
+    if ((hw->phy_type == e1000_phy_igp ||
+        hw->phy_type == e1000_phy_igp_3 ||
         hw->phy_type == e1000_phy_igp_2) &&
        (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
         ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
@@ -3299,7 +3472,8 @@
     if (e1000_swfw_sync_acquire(hw, swfw))
         return -E1000_ERR_SWFW_SYNC;
 
-    if((hw->phy_type == e1000_phy_igp ||
+    if ((hw->phy_type == e1000_phy_igp ||
+        hw->phy_type == e1000_phy_igp_3 ||
         hw->phy_type == e1000_phy_igp_2) &&
        (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
         ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
@@ -3514,7 +3688,7 @@
         E1000_WRITE_FLUSH(hw);
 
         if (hw->mac_type >= e1000_82571)
-            msec_delay(10);
+            msec_delay_irq(10);
         e1000_swfw_sync_release(hw, swfw);
     } else {
         /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
@@ -3544,6 +3718,12 @@
     ret_val = e1000_get_phy_cfg_done(hw);
     e1000_release_software_semaphore(hw);
 
+        if ((hw->mac_type == e1000_ich8lan) &&
+            (hw->phy_type == e1000_phy_igp_3)) {
+            ret_val = e1000_init_lcd_from_nvm(hw);
+            if (ret_val)
+                return ret_val;
+        }
     return ret_val;
 }
 
@@ -3572,9 +3752,11 @@
     case e1000_82541_rev_2:
     case e1000_82571:
     case e1000_82572:
+    case e1000_ich8lan:
         ret_val = e1000_phy_hw_reset(hw);
         if(ret_val)
             return ret_val;
+
         break;
     default:
         ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
@@ -3597,11 +3779,120 @@
 }
 
 /******************************************************************************
+* Work-around for 82566 power-down: on D3 entry-
+* 1) disable gigabit link
+* 2) write VR power-down enable
+* 3) read it back
+* if successful continue, else issue LCD reset and repeat
+*
+* hw - struct containing variables accessed by shared code
+******************************************************************************/
+void
+e1000_phy_powerdown_workaround(struct e1000_hw *hw)
+{
+    int32_t reg;
+    uint16_t phy_data;
+    int32_t retry = 0;
+
+    DEBUGFUNC("e1000_phy_powerdown_workaround");
+
+    if (hw->phy_type != e1000_phy_igp_3)
+        return;
+
+    do {
+        /* Disable link */
+        reg = E1000_READ_REG(hw, PHY_CTRL);
+        E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
+                        E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+
+        /* Write VR power-down enable */
+        e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
+        e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data |
+                            IGP3_VR_CTRL_MODE_SHUT);
+
+        /* Read it back and test */
+        e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
+        if ((phy_data & IGP3_VR_CTRL_MODE_SHUT) || retry)
+            break;
+
+        /* Issue PHY reset and repeat at most one more time */
+        reg = E1000_READ_REG(hw, CTRL);
+        E1000_WRITE_REG(hw, CTRL, reg | E1000_CTRL_PHY_RST);
+        retry++;
+    } while (retry);
+
+    return;
+
+}
+
+/******************************************************************************
+* Work-around for 82566 Kumeran PCS lock loss:
+* On link status change (i.e. PCI reset, speed change) and link is up and
+* speed is gigabit-
+* 0) if workaround is optionally disabled do nothing
+* 1) wait 1ms for Kumeran link to come up
+* 2) check Kumeran Diagnostic register PCS lock loss bit
+* 3) if not set the link is locked (all is good), otherwise...
+* 4) reset the PHY
+* 5) repeat up to 10 times
+* Note: this is only called for IGP3 copper when speed is 1gb.
+*
+* hw - struct containing variables accessed by shared code
+******************************************************************************/
+int32_t
+e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw)
+{
+    int32_t ret_val;
+    int32_t reg;
+    int32_t cnt;
+    uint16_t phy_data;
+
+    if (hw->kmrn_lock_loss_workaround_disabled)
+        return E1000_SUCCESS;
+
+    /* Make sure link is up before proceeding. If not just return.
+     * Attempting this while link is negotiating fouls up link
+     * stability */
+    ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+    ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+
+    if (phy_data & MII_SR_LINK_STATUS) {
+        for (cnt = 0; cnt < 10; cnt++) {
+            /* read once to clear */
+            ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
+            if (ret_val)
+                return ret_val;
+            /* and again to get new status */
+            ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
+            if (ret_val)
+                return ret_val;
+
+            /* check for PCS lock */
+            if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS))
+                return E1000_SUCCESS;
+
+            /* Issue PHY reset */
+            e1000_phy_hw_reset(hw);
+            msec_delay_irq(5);
+        }
+        /* Disable GigE link negotiation */
+        reg = E1000_READ_REG(hw, PHY_CTRL);
+        E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
+                        E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+
+        /* unable to acquire PCS lock */
+        return E1000_ERR_PHY;
+    }
+
+    return E1000_SUCCESS;
+}
+
+/******************************************************************************
 * Probes the expected PHY address for known PHY IDs
 *
 * hw - Struct containing variables accessed by shared code
 ******************************************************************************/
-static int32_t
+int32_t
 e1000_detect_gig_phy(struct e1000_hw *hw)
 {
     int32_t phy_init_status, ret_val;
@@ -3613,8 +3904,8 @@
     /* The 82571 firmware may still be configuring the PHY.  In this
      * case, we cannot access the PHY until the configuration is done.  So
      * we explicitly set the PHY values. */
-    if(hw->mac_type == e1000_82571 ||
-       hw->mac_type == e1000_82572) {
+    if (hw->mac_type == e1000_82571 ||
+        hw->mac_type == e1000_82572) {
         hw->phy_id = IGP01E1000_I_PHY_ID;
         hw->phy_type = e1000_phy_igp_2;
         return E1000_SUCCESS;
@@ -3631,7 +3922,7 @@
 
     /* Read the PHY ID Registers to identify which PHY is onboard. */
     ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
-    if(ret_val)
+    if (ret_val)
         return ret_val;
 
     hw->phy_id = (uint32_t) (phy_id_high << 16);
@@ -3669,6 +3960,12 @@
     case e1000_80003es2lan:
         if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE;
         break;
+    case e1000_ich8lan:
+        if (hw->phy_id == IGP03E1000_E_PHY_ID) match = TRUE;
+        if (hw->phy_id == IFE_E_PHY_ID) match = TRUE;
+        if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = TRUE;
+        if (hw->phy_id == IFE_C_E_PHY_ID) match = TRUE;
+        break;
     default:
         DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
         return -E1000_ERR_CONFIG;
@@ -3784,6 +4081,53 @@
 }
 
 /******************************************************************************
+* Get PHY information from various PHY registers for ife PHY only.
+*
+* hw - Struct containing variables accessed by shared code
+* phy_info - PHY information structure
+******************************************************************************/
+int32_t
+e1000_phy_ife_get_info(struct e1000_hw *hw,
+                       struct e1000_phy_info *phy_info)
+{
+    int32_t ret_val;
+    uint16_t phy_data, polarity;
+
+    DEBUGFUNC("e1000_phy_ife_get_info");
+
+    phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
+    phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+
+    ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
+    if (ret_val)
+        return ret_val;
+    phy_info->polarity_correction =
+                        (phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >>
+                        IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT;
+
+    if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) {
+        ret_val = e1000_check_polarity(hw, &polarity);
+        if (ret_val)
+            return ret_val;
+    } else {
+        /* Polarity is forced. */
+        polarity = (phy_data & IFE_PSC_FORCE_POLARITY) >>
+                       IFE_PSC_FORCE_POLARITY_SHIFT;
+    }
+    phy_info->cable_polarity = polarity;
+
+    ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
+    if (ret_val)
+        return ret_val;
+
+    phy_info->mdix_mode =
+                     (phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >>
+                     IFE_PMC_MDIX_MODE_SHIFT;
+
+    return E1000_SUCCESS;
+}
+
+/******************************************************************************
 * Get PHY information from various PHY registers fot m88 PHY only.
 *
 * hw - Struct containing variables accessed by shared code
@@ -3898,9 +4242,12 @@
         return -E1000_ERR_CONFIG;
     }
 
-    if(hw->phy_type == e1000_phy_igp ||
+    if (hw->phy_type == e1000_phy_igp ||
+        hw->phy_type == e1000_phy_igp_3 ||
         hw->phy_type == e1000_phy_igp_2)
         return e1000_phy_igp_get_info(hw, phy_info);
+    else if (hw->phy_type == e1000_phy_ife)
+        return e1000_phy_ife_get_info(hw, phy_info);
     else
         return e1000_phy_m88_get_info(hw, phy_info);
 }
@@ -4049,6 +4396,35 @@
         eeprom->use_eerd = TRUE;
         eeprom->use_eewr = FALSE;
         break;
+    case e1000_ich8lan:
+    {
+        int32_t  i = 0;
+        uint32_t flash_size = E1000_READ_ICH8_REG(hw, ICH8_FLASH_GFPREG);
+
+        eeprom->type = e1000_eeprom_ich8;
+        eeprom->use_eerd = FALSE;
+        eeprom->use_eewr = FALSE;
+        eeprom->word_size = E1000_SHADOW_RAM_WORDS;
+
+        /* Zero the shadow RAM structure. But don't load it from NVM
+         * so as to save time for driver init */
+        if (hw->eeprom_shadow_ram != NULL) {
+            for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
+                hw->eeprom_shadow_ram[i].modified = FALSE;
+                hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
+            }
+        }
+
+        hw->flash_base_addr = (flash_size & ICH8_GFPREG_BASE_MASK) *
+                              ICH8_FLASH_SECTOR_SIZE;
+
+        hw->flash_bank_size = ((flash_size >> 16) & ICH8_GFPREG_BASE_MASK) + 1;
+        hw->flash_bank_size -= (flash_size & ICH8_GFPREG_BASE_MASK);
+        hw->flash_bank_size *= ICH8_FLASH_SECTOR_SIZE;
+        hw->flash_bank_size /= 2 * sizeof(uint16_t);
+
+        break;
+    }
     default:
         break;
     }
@@ -4469,7 +4845,10 @@
         return ret_val;
     }
 
-    if(eeprom->type == e1000_eeprom_spi) {
+    if (eeprom->type == e1000_eeprom_ich8)
+        return e1000_read_eeprom_ich8(hw, offset, words, data);
+
+    if (eeprom->type == e1000_eeprom_spi) {
         uint16_t word_in;
         uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
 
@@ -4636,7 +5015,10 @@
 
     DEBUGFUNC("e1000_is_onboard_nvm_eeprom");
 
-    if(hw->mac_type == e1000_82573) {
+    if (hw->mac_type == e1000_ich8lan)
+        return FALSE;
+
+    if (hw->mac_type == e1000_82573) {
         eecd = E1000_READ_REG(hw, EECD);
 
         /* Isolate bits 15 & 16 */
@@ -4686,8 +5068,22 @@
         }
     }
 
-    for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
-        if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+    if (hw->mac_type == e1000_ich8lan) {
+        /* Drivers must allocate the shadow ram structure for the
+         * EEPROM checksum to be updated.  Otherwise, this bit as well
+         * as the checksum must both be set correctly for this
+         * validation to pass.
+         */
+        e1000_read_eeprom(hw, 0x19, 1, &eeprom_data);
+        if ((eeprom_data & 0x40) == 0) {
+            eeprom_data |= 0x40;
+            e1000_write_eeprom(hw, 0x19, 1, &eeprom_data);
+            e1000_update_eeprom_checksum(hw);
+        }
+    }
+
+    for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+        if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
             DEBUGOUT("EEPROM Read Error\n");
             return -E1000_ERR_EEPROM;
         }
@@ -4713,6 +5109,7 @@
 int32_t
 e1000_update_eeprom_checksum(struct e1000_hw *hw)
 {
+    uint32_t ctrl_ext;
     uint16_t checksum = 0;
     uint16_t i, eeprom_data;
 
@@ -4731,6 +5128,14 @@
         return -E1000_ERR_EEPROM;
     } else if (hw->eeprom.type == e1000_eeprom_flash) {
         e1000_commit_shadow_ram(hw);
+    } else if (hw->eeprom.type == e1000_eeprom_ich8) {
+        e1000_commit_shadow_ram(hw);
+        /* Reload the EEPROM, or else modifications will not appear
+         * until after next adapter reset. */
+        ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+        ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+        E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+        msec_delay(10);
     }
     return E1000_SUCCESS;
 }
@@ -4770,6 +5175,9 @@
     if(eeprom->use_eewr == TRUE)
         return e1000_write_eeprom_eewr(hw, offset, words, data);
 
+    if (eeprom->type == e1000_eeprom_ich8)
+        return e1000_write_eeprom_ich8(hw, offset, words, data);
+
     /* Prepare the EEPROM for writing  */
     if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
         return -E1000_ERR_EEPROM;
@@ -4957,11 +5365,17 @@
     uint32_t flop = 0;
     uint32_t i = 0;
     int32_t error = E1000_SUCCESS;
-
-    /* The flop register will be used to determine if flash type is STM */
-    flop = E1000_READ_REG(hw, FLOP);
+    uint32_t old_bank_offset = 0;
+    uint32_t new_bank_offset = 0;
+    uint32_t sector_retries = 0;
+    uint8_t low_byte = 0;
+    uint8_t high_byte = 0;
+    uint8_t temp_byte = 0;
+    boolean_t sector_write_failed = FALSE;
 
     if (hw->mac_type == e1000_82573) {
+        /* The flop register will be used to determine if flash type is STM */
+        flop = E1000_READ_REG(hw, FLOP);
         for (i=0; i < attempts; i++) {
             eecd = E1000_READ_REG(hw, EECD);
             if ((eecd & E1000_EECD_FLUPD) == 0) {
@@ -4995,6 +5409,106 @@
         }
     }
 
+    if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) {
+        /* We're writing to the opposite bank so if we're on bank 1,
+         * write to bank 0 etc.  We also need to erase the segment that
+         * is going to be written */
+        if (!(E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL)) {
+            new_bank_offset = hw->flash_bank_size * 2;
+            old_bank_offset = 0;
+            e1000_erase_ich8_4k_segment(hw, 1);
+        } else {
+            old_bank_offset = hw->flash_bank_size * 2;
+            new_bank_offset = 0;
+            e1000_erase_ich8_4k_segment(hw, 0);
+        }
+
+        do {
+            sector_write_failed = FALSE;
+            /* Loop for every byte in the shadow RAM,
+             * which is in units of words. */
+            for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
+                /* Determine whether to write the value stored
+                 * in the other NVM bank or a modified value stored
+                 * in the shadow RAM */
+                if (hw->eeprom_shadow_ram[i].modified == TRUE) {
+                    low_byte = (uint8_t)hw->eeprom_shadow_ram[i].eeprom_word;
+                    e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset,
+                                         &temp_byte);
+                    udelay(100);
+                    error = e1000_verify_write_ich8_byte(hw,
+                                                 (i << 1) + new_bank_offset,
+                                                 low_byte);
+                    if (error != E1000_SUCCESS)
+                        sector_write_failed = TRUE;
+                    high_byte =
+                        (uint8_t)(hw->eeprom_shadow_ram[i].eeprom_word >> 8);
+                    e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
+                                         &temp_byte);
+                    udelay(100);
+                } else {
+                    e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset,
+                                         &low_byte);
+                    udelay(100);
+                    error = e1000_verify_write_ich8_byte(hw,
+                                 (i << 1) + new_bank_offset, low_byte);
+                    if (error != E1000_SUCCESS)
+                        sector_write_failed = TRUE;
+                    e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
+                                         &high_byte);
+                }
+
+                /* If the word is 0x13, then make sure the signature bits
+                 * (15:14) are 11b until the commit has completed.
+                 * This will allow us to write 10b which indicates the
+                 * signature is valid.  We want to do this after the write
+                 * has completed so that we don't mark the segment valid
+                 * while the write is still in progress */
+                if (i == E1000_ICH8_NVM_SIG_WORD)
+                    high_byte = E1000_ICH8_NVM_SIG_MASK | high_byte;
+
+                error = e1000_verify_write_ich8_byte(hw,
+                             (i << 1) + new_bank_offset + 1, high_byte);
+                if (error != E1000_SUCCESS)
+                    sector_write_failed = TRUE;
+
+                if (sector_write_failed == FALSE) {
+                    /* Clear the now not used entry in the cache */
+                    hw->eeprom_shadow_ram[i].modified = FALSE;
+                    hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
+                }
+            }
+
+            /* Don't bother writing the segment valid bits if sector
+             * programming failed. */
+            if (sector_write_failed == FALSE) {
+                /* Finally validate the new segment by setting bit 15:14
+                 * to 10b in word 0x13 , this can be done without an
+                 * erase as well since these bits are 11 to start with
+                 * and we need to change bit 14 to 0b */
+                e1000_read_ich8_byte(hw,
+                    E1000_ICH8_NVM_SIG_WORD * 2 + 1 + new_bank_offset,
+                    &high_byte);
+                high_byte &= 0xBF;
+                error = e1000_verify_write_ich8_byte(hw,
+                            E1000_ICH8_NVM_SIG_WORD * 2 + 1 + new_bank_offset,
+                            high_byte);
+                if (error != E1000_SUCCESS)
+                    sector_write_failed = TRUE;
+
+                /* And invalidate the previously valid segment by setting
+                 * its signature word (0x13) high_byte to 0b. This can be
+                 * done without an erase because flash erase sets all bits
+                 * to 1's. We can write 1's to 0's without an erase */
+                error = e1000_verify_write_ich8_byte(hw,
+                            E1000_ICH8_NVM_SIG_WORD * 2 + 1 + old_bank_offset,
+                            0);
+                if (error != E1000_SUCCESS)
+                    sector_write_failed = TRUE;
+            }
+        } while (++sector_retries < 10 && sector_write_failed == TRUE);
+    }
+
     return error;
 }
 
@@ -5102,15 +5616,19 @@
      * the other port. */
     if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
         rar_num -= 1;
+    if (hw->mac_type == e1000_ich8lan)
+        rar_num = E1000_RAR_ENTRIES_ICH8LAN;
+
     /* Zero out the other 15 receive addresses. */
     DEBUGOUT("Clearing RAR[1-15]\n");
     for(i = 1; i < rar_num; i++) {
         E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+        E1000_WRITE_FLUSH(hw);
         E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+        E1000_WRITE_FLUSH(hw);
     }
 }
 
-#if 0
 /******************************************************************************
  * Updates the MAC's list of multicast addresses.
  *
@@ -5145,6 +5663,8 @@
     /* Clear RAR[1-15] */
     DEBUGOUT(" Clearing RAR[1-15]\n");
     num_rar_entry = E1000_RAR_ENTRIES;
+    if (hw->mac_type == e1000_ich8lan)
+        num_rar_entry = E1000_RAR_ENTRIES_ICH8LAN;
     /* Reserve a spot for the Locally Administered Address to work around
      * an 82571 issue in which a reset on one port will reload the MAC on
      * the other port. */
@@ -5153,14 +5673,19 @@
 
     for(i = rar_used_count; i < num_rar_entry; i++) {
         E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+        E1000_WRITE_FLUSH(hw);
         E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+        E1000_WRITE_FLUSH(hw);
     }
 
     /* Clear the MTA */
     DEBUGOUT(" Clearing MTA\n");
     num_mta_entry = E1000_NUM_MTA_REGISTERS;
+    if (hw->mac_type == e1000_ich8lan)
+        num_mta_entry = E1000_NUM_MTA_REGISTERS_ICH8LAN;
     for(i = 0; i < num_mta_entry; i++) {
         E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+        E1000_WRITE_FLUSH(hw);
     }
 
     /* Add the new addresses */
@@ -5194,7 +5719,6 @@
     }
     DEBUGOUT("MC Update Complete\n");
 }
-#endif  /*  0  */
 
 /******************************************************************************
  * Hashes an address to determine its location in the multicast table
@@ -5217,24 +5741,46 @@
      * LSB                 MSB
      */
     case 0:
-        /* [47:36] i.e. 0x563 for above example address */
-        hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+        if (hw->mac_type == e1000_ich8lan) {
+            /* [47:38] i.e. 0x158 for above example address */
+            hash_value = ((mc_addr[4] >> 6) | (((uint16_t) mc_addr[5]) << 2));
+        } else {
+            /* [47:36] i.e. 0x563 for above example address */
+            hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+        }
         break;
     case 1:
-        /* [46:35] i.e. 0xAC6 for above example address */
-        hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
+        if (hw->mac_type == e1000_ich8lan) {
+            /* [46:37] i.e. 0x2B1 for above example address */
+            hash_value = ((mc_addr[4] >> 5) | (((uint16_t) mc_addr[5]) << 3));
+        } else {
+            /* [46:35] i.e. 0xAC6 for above example address */
+            hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
+        }
         break;
     case 2:
-        /* [45:34] i.e. 0x5D8 for above example address */
-        hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+        if (hw->mac_type == e1000_ich8lan) {
+            /*[45:36] i.e. 0x163 for above example address */
+            hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+        } else {
+            /* [45:34] i.e. 0x5D8 for above example address */
+            hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+        }
         break;
     case 3:
-        /* [43:32] i.e. 0x634 for above example address */
-        hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
+        if (hw->mac_type == e1000_ich8lan) {
+            /* [43:34] i.e. 0x18D for above example address */
+            hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+        } else {
+            /* [43:32] i.e. 0x634 for above example address */
+            hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
+        }
         break;
     }
 
     hash_value &= 0xFFF;
+    if (hw->mac_type == e1000_ich8lan)
+        hash_value &= 0x3FF;
 
     return hash_value;
 }
@@ -5262,6 +5808,8 @@
      * register are determined by the lower 5 bits of the value.
      */
     hash_reg = (hash_value >> 5) & 0x7F;
+    if (hw->mac_type == e1000_ich8lan)
+        hash_reg &= 0x1F;
     hash_bit = hash_value & 0x1F;
 
     mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg);
@@ -5275,9 +5823,12 @@
     if((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) {
         temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1));
         E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
+        E1000_WRITE_FLUSH(hw);
         E1000_WRITE_REG_ARRAY(hw, MTA, (hash_reg - 1), temp);
+        E1000_WRITE_FLUSH(hw);
     } else {
         E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
+        E1000_WRITE_FLUSH(hw);
     }
 }
 
@@ -5334,7 +5885,9 @@
     }
 
     E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
+    E1000_WRITE_FLUSH(hw);
     E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
+    E1000_WRITE_FLUSH(hw);
 }
 
 /******************************************************************************
@@ -5351,12 +5904,18 @@
 {
     uint32_t temp;
 
-    if((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
+    if (hw->mac_type == e1000_ich8lan)
+        return;
+
+    if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
         temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
         E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+        E1000_WRITE_FLUSH(hw);
         E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
+        E1000_WRITE_FLUSH(hw);
     } else {
         E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+        E1000_WRITE_FLUSH(hw);
     }
 }
 
@@ -5373,6 +5932,9 @@
     uint32_t vfta_offset = 0;
     uint32_t vfta_bit_in_reg = 0;
 
+    if (hw->mac_type == e1000_ich8lan)
+        return;
+
     if (hw->mac_type == e1000_82573) {
         if (hw->mng_cookie.vlan_id != 0) {
             /* The VFTA is a 4096b bit-field, each identifying a single VLAN
@@ -5392,6 +5954,7 @@
          * manageability unit */
         vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
         E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
+        E1000_WRITE_FLUSH(hw);
     }
 }
 
@@ -5421,9 +5984,18 @@
         DEBUGOUT("EEPROM Read Error\n");
         return -E1000_ERR_EEPROM;
     }
-    if((eeprom_data== ID_LED_RESERVED_0000) ||
-       (eeprom_data == ID_LED_RESERVED_FFFF)) eeprom_data = ID_LED_DEFAULT;
-    for(i = 0; i < 4; i++) {
+
+    if ((hw->mac_type == e1000_82573) &&
+        (eeprom_data == ID_LED_RESERVED_82573))
+        eeprom_data = ID_LED_DEFAULT_82573;
+    else if ((eeprom_data == ID_LED_RESERVED_0000) ||
+            (eeprom_data == ID_LED_RESERVED_FFFF)) {
+        if (hw->mac_type == e1000_ich8lan)
+            eeprom_data = ID_LED_DEFAULT_ICH8LAN;
+        else
+            eeprom_data = ID_LED_DEFAULT;
+    }
+    for (i = 0; i < 4; i++) {
         temp = (eeprom_data >> (i << 2)) & led_mask;
         switch(temp) {
         case ID_LED_ON1_DEF2:
@@ -5519,6 +6091,44 @@
 }
 
 /******************************************************************************
+ * Used on 82571 and later Si that has LED blink bits.
+ * Callers must use their own timer and should have already called
+ * e1000_id_led_init()
+ * Call e1000_cleanup led() to stop blinking
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+int32_t
+e1000_blink_led_start(struct e1000_hw *hw)
+{
+    int16_t  i;
+    uint32_t ledctl_blink = 0;
+
+    DEBUGFUNC("e1000_id_led_blink_on");
+
+    if (hw->mac_type < e1000_82571) {
+        /* Nothing to do */
+        return E1000_SUCCESS;
+    }
+    if (hw->media_type == e1000_media_type_fiber) {
+        /* always blink LED0 for PCI-E fiber */
+        ledctl_blink = E1000_LEDCTL_LED0_BLINK |
+                     (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
+    } else {
+        /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */
+        ledctl_blink = hw->ledctl_mode2;
+        for (i=0; i < 4; i++)
+            if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) ==
+                E1000_LEDCTL_MODE_LED_ON)
+                ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8));
+    }
+
+    E1000_WRITE_REG(hw, LEDCTL, ledctl_blink);
+
+    return E1000_SUCCESS;
+}
+
+/******************************************************************************
  * Restores the saved state of the SW controlable LED.
  *
  * hw - Struct containing variables accessed by shared code
@@ -5548,6 +6158,10 @@
             return ret_val;
         /* Fall Through */
     default:
+        if (hw->phy_type == e1000_phy_ife) {
+            e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
+            break;
+        }
         /* Restore LEDCTL settings */
         E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default);
         break;
@@ -5592,7 +6206,10 @@
             /* Clear SW Defineable Pin 0 to turn on the LED */
             ctrl &= ~E1000_CTRL_SWDPIN0;
             ctrl |= E1000_CTRL_SWDPIO0;
-        } else if(hw->media_type == e1000_media_type_copper) {
+        } else if (hw->phy_type == e1000_phy_ife) {
+            e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+                 (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
+        } else if (hw->media_type == e1000_media_type_copper) {
             E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2);
             return E1000_SUCCESS;
         }
@@ -5640,7 +6257,10 @@
             /* Set SW Defineable Pin 0 to turn off the LED */
             ctrl |= E1000_CTRL_SWDPIN0;
             ctrl |= E1000_CTRL_SWDPIO0;
-        } else if(hw->media_type == e1000_media_type_copper) {
+        } else if (hw->phy_type == e1000_phy_ife) {
+            e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+                 (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
+        } else if (hw->media_type == e1000_media_type_copper) {
             E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
             return E1000_SUCCESS;
         }
@@ -5678,12 +6298,16 @@
     temp = E1000_READ_REG(hw, XOFFRXC);
     temp = E1000_READ_REG(hw, XOFFTXC);
     temp = E1000_READ_REG(hw, FCRUC);
+
+    if (hw->mac_type != e1000_ich8lan) {
     temp = E1000_READ_REG(hw, PRC64);
     temp = E1000_READ_REG(hw, PRC127);
     temp = E1000_READ_REG(hw, PRC255);
     temp = E1000_READ_REG(hw, PRC511);
     temp = E1000_READ_REG(hw, PRC1023);
     temp = E1000_READ_REG(hw, PRC1522);
+    }
+
     temp = E1000_READ_REG(hw, GPRC);
     temp = E1000_READ_REG(hw, BPRC);
     temp = E1000_READ_REG(hw, MPRC);
@@ -5703,12 +6327,16 @@
     temp = E1000_READ_REG(hw, TOTH);
     temp = E1000_READ_REG(hw, TPR);
     temp = E1000_READ_REG(hw, TPT);
+
+    if (hw->mac_type != e1000_ich8lan) {
     temp = E1000_READ_REG(hw, PTC64);
     temp = E1000_READ_REG(hw, PTC127);
     temp = E1000_READ_REG(hw, PTC255);
     temp = E1000_READ_REG(hw, PTC511);
     temp = E1000_READ_REG(hw, PTC1023);
     temp = E1000_READ_REG(hw, PTC1522);
+    }
+
     temp = E1000_READ_REG(hw, MPTC);
     temp = E1000_READ_REG(hw, BPTC);
 
@@ -5731,6 +6359,9 @@
 
     temp = E1000_READ_REG(hw, IAC);
     temp = E1000_READ_REG(hw, ICRXOC);
+
+    if (hw->mac_type == e1000_ich8lan) return;
+
     temp = E1000_READ_REG(hw, ICRXPTC);
     temp = E1000_READ_REG(hw, ICRXATC);
     temp = E1000_READ_REG(hw, ICTXPTC);
@@ -5911,6 +6542,7 @@
         hw->bus_width = e1000_bus_width_pciex_1;
         break;
     case e1000_82571:
+    case e1000_ich8lan:
     case e1000_80003es2lan:
         hw->bus_type = e1000_bus_type_pci_express;
         hw->bus_speed = e1000_bus_speed_2500;
@@ -5948,8 +6580,6 @@
         break;
     }
 }
-
-#if 0
 /******************************************************************************
  * Reads a value from one of the devices registers using port I/O (as opposed
  * memory mapped I/O). Only 82544 and newer devices support port I/O.
@@ -5967,7 +6597,6 @@
     e1000_io_write(hw, io_addr, offset);
     return e1000_io_read(hw, io_data);
 }
-#endif  /*  0  */
 
 /******************************************************************************
  * Writes a value to one of the devices registers using port I/O (as opposed to
@@ -6012,8 +6641,6 @@
 {
     int32_t ret_val;
     uint16_t agc_value = 0;
-    uint16_t cur_agc, min_agc = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
-    uint16_t max_agc = 0;
     uint16_t i, phy_data;
     uint16_t cable_length;
 
@@ -6086,6 +6713,8 @@
             break;
         }
     } else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+        uint16_t cur_agc_value;
+        uint16_t min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
         uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
                                                          {IGP01E1000_PHY_AGC_A,
                                                           IGP01E1000_PHY_AGC_B,
@@ -6098,23 +6727,23 @@
             if(ret_val)
                 return ret_val;
 
-            cur_agc = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
+            cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
 
-            /* Array bound check. */
-            if((cur_agc >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
-               (cur_agc == 0))
+            /* Value bound check. */
+            if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
+                (cur_agc_value == 0))
                 return -E1000_ERR_PHY;
 
-            agc_value += cur_agc;
+            agc_value += cur_agc_value;
 
             /* Update minimal AGC value. */
-            if(min_agc > cur_agc)
-                min_agc = cur_agc;
+            if (min_agc_value > cur_agc_value)
+                min_agc_value = cur_agc_value;
         }
 
         /* Remove the minimal AGC result for length < 50m */
-        if(agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
-            agc_value -= min_agc;
+        if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
+            agc_value -= min_agc_value;
 
             /* Get the average length of the remaining 3 channels */
             agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
@@ -6130,7 +6759,10 @@
                        IGP01E1000_AGC_RANGE) : 0;
         *max_length = e1000_igp_cable_length_table[agc_value] +
                       IGP01E1000_AGC_RANGE;
-    } else if (hw->phy_type == e1000_phy_igp_2) {
+    } else if (hw->phy_type == e1000_phy_igp_2 ||
+               hw->phy_type == e1000_phy_igp_3) {
+        uint16_t cur_agc_index, max_agc_index = 0;
+        uint16_t min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1;
         uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
                                                          {IGP02E1000_PHY_AGC_A,
                                                           IGP02E1000_PHY_AGC_B,
@@ -6145,19 +6777,27 @@
 	    /* Getting bits 15:9, which represent the combination of course and
              * fine gain values.  The result is a number that can be put into
              * the lookup table to obtain the approximate cable length. */
-            cur_agc = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
-                      IGP02E1000_AGC_LENGTH_MASK;
+            cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
+                            IGP02E1000_AGC_LENGTH_MASK;
+
+            /* Array index bound check. */
+            if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) ||
+                (cur_agc_index == 0))
+                return -E1000_ERR_PHY;
 
             /* Remove min & max AGC values from calculation. */
-            if (e1000_igp_2_cable_length_table[min_agc] > e1000_igp_2_cable_length_table[cur_agc])
-                min_agc = cur_agc;
-	    if (e1000_igp_2_cable_length_table[max_agc] < e1000_igp_2_cable_length_table[cur_agc])
-                max_agc = cur_agc;
+            if (e1000_igp_2_cable_length_table[min_agc_index] >
+                e1000_igp_2_cable_length_table[cur_agc_index])
+                min_agc_index = cur_agc_index;
+            if (e1000_igp_2_cable_length_table[max_agc_index] <
+                e1000_igp_2_cable_length_table[cur_agc_index])
+                max_agc_index = cur_agc_index;
 
-            agc_value += e1000_igp_2_cable_length_table[cur_agc];
+            agc_value += e1000_igp_2_cable_length_table[cur_agc_index];
         }
 
-        agc_value -= (e1000_igp_2_cable_length_table[min_agc] + e1000_igp_2_cable_length_table[max_agc]);
+        agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] +
+                      e1000_igp_2_cable_length_table[max_agc_index]);
         agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
 
         /* Calculate cable length with the error range of +/- 10 meters. */
@@ -6203,7 +6843,8 @@
             return ret_val;
         *polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >>
                     M88E1000_PSSR_REV_POLARITY_SHIFT;
-    } else if(hw->phy_type == e1000_phy_igp ||
+    } else if (hw->phy_type == e1000_phy_igp ||
+              hw->phy_type == e1000_phy_igp_3 ||
               hw->phy_type == e1000_phy_igp_2) {
         /* Read the Status register to check the speed */
         ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
@@ -6229,6 +6870,13 @@
              * 100 Mbps this bit is always 0) */
             *polarity = phy_data & IGP01E1000_PSSR_POLARITY_REVERSED;
         }
+    } else if (hw->phy_type == e1000_phy_ife) {
+        ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL,
+                                     &phy_data);
+        if (ret_val)
+            return ret_val;
+        *polarity = (phy_data & IFE_PESC_POLARITY_REVERSED) >>
+                           IFE_PESC_POLARITY_REVERSED_SHIFT;
     }
     return E1000_SUCCESS;
 }
@@ -6256,7 +6904,8 @@
 
     DEBUGFUNC("e1000_check_downshift");
 
-    if(hw->phy_type == e1000_phy_igp ||
+    if (hw->phy_type == e1000_phy_igp ||
+        hw->phy_type == e1000_phy_igp_3 ||
         hw->phy_type == e1000_phy_igp_2) {
         ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
                                      &phy_data);
@@ -6273,6 +6922,9 @@
 
         hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
                                M88E1000_PSSR_DOWNSHIFT_SHIFT;
+    } else if (hw->phy_type == e1000_phy_ife) {
+        /* e1000_phy_ife supports 10/100 speed only */
+        hw->speed_downgraded = FALSE;
     }
 
     return E1000_SUCCESS;
@@ -6317,7 +6969,9 @@
 
         if(speed == SPEED_1000) {
 
-            e1000_get_cable_length(hw, &min_length, &max_length);
+            ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
+            if (ret_val)
+                return ret_val;
 
             if((hw->dsp_config_state == e1000_dsp_config_enabled) &&
                 min_length >= e1000_igp_cable_length_50) {
@@ -6525,20 +7179,27 @@
 e1000_set_d3_lplu_state(struct e1000_hw *hw,
                         boolean_t active)
 {
+    uint32_t phy_ctrl = 0;
     int32_t ret_val;
     uint16_t phy_data;
     DEBUGFUNC("e1000_set_d3_lplu_state");
 
-    if(hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2)
+    if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
+        && hw->phy_type != e1000_phy_igp_3)
         return E1000_SUCCESS;
 
     /* During driver activity LPLU should not be used or it will attain link
      * from the lowest speeds starting from 10Mbps. The capability is used for
      * Dx transitions and states */
-    if(hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
+    if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
         ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
-        if(ret_val)
+        if (ret_val)
             return ret_val;
+    } else if (hw->mac_type == e1000_ich8lan) {
+        /* MAC writes into PHY register based on the state transition
+         * and start auto-negotiation. SW driver can overwrite the settings
+         * in CSR PHY power control E1000_PHY_CTRL register. */
+        phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
     } else {
         ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
         if(ret_val)
@@ -6553,11 +7214,16 @@
             if(ret_val)
                 return ret_val;
         } else {
+            if (hw->mac_type == e1000_ich8lan) {
+                phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
+                E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+            } else {
                 phy_data &= ~IGP02E1000_PM_D3_LPLU;
                 ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
                                               phy_data);
                 if (ret_val)
                     return ret_val;
+            }
         }
 
         /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used during
@@ -6593,17 +7259,22 @@
               (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
 
         if(hw->mac_type == e1000_82541_rev_2 ||
-           hw->mac_type == e1000_82547_rev_2) {
+            hw->mac_type == e1000_82547_rev_2) {
             phy_data |= IGP01E1000_GMII_FLEX_SPD;
             ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
             if(ret_val)
                 return ret_val;
         } else {
+            if (hw->mac_type == e1000_ich8lan) {
+                phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
+                E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+            } else {
                 phy_data |= IGP02E1000_PM_D3_LPLU;
                 ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
                                               phy_data);
                 if (ret_val)
                     return ret_val;
+            }
         }
 
         /* When LPLU is enabled we should disable SmartSpeed */
@@ -6638,6 +7309,7 @@
 e1000_set_d0_lplu_state(struct e1000_hw *hw,
                         boolean_t active)
 {
+    uint32_t phy_ctrl = 0;
     int32_t ret_val;
     uint16_t phy_data;
     DEBUGFUNC("e1000_set_d0_lplu_state");
@@ -6645,15 +7317,24 @@
     if(hw->mac_type <= e1000_82547_rev_2)
         return E1000_SUCCESS;
 
+    if (hw->mac_type == e1000_ich8lan) {
+        phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
+    } else {
         ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
         if(ret_val)
             return ret_val;
+    }
 
     if (!active) {
+        if (hw->mac_type == e1000_ich8lan) {
+            phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
+            E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+        } else {
             phy_data &= ~IGP02E1000_PM_D0_LPLU;
             ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
             if (ret_val)
                 return ret_val;
+        }
 
         /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used during
          * Dx states where the power conservation is most important.  During
@@ -6686,10 +7367,15 @@
 
     } else {
 
+        if (hw->mac_type == e1000_ich8lan) {
+            phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
+            E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+        } else {
             phy_data |= IGP02E1000_PM_D0_LPLU;
             ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
             if (ret_val)
                 return ret_val;
+        }
 
         /* When LPLU is enabled we should disable SmartSpeed */
         ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
@@ -6928,8 +7614,10 @@
 
     length >>= 2;
     /* The device driver writes the relevant command block into the ram area. */
-    for (i = 0; i < length; i++)
+    for (i = 0; i < length; i++) {
         E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((uint32_t *) hdr + i));
+        E1000_WRITE_FLUSH(hw);
+    }
 
     return E1000_SUCCESS;
 }
@@ -6961,15 +7649,18 @@
  * returns  - TRUE when the mode is IAMT or FALSE.
  ****************************************************************************/
 boolean_t
-e1000_check_mng_mode(
-    struct e1000_hw *hw)
+e1000_check_mng_mode(struct e1000_hw *hw)
 {
     uint32_t fwsm;
 
     fwsm = E1000_READ_REG(hw, FWSM);
 
-    if((fwsm & E1000_FWSM_MODE_MASK) ==
-        (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+    if (hw->mac_type == e1000_ich8lan) {
+        if ((fwsm & E1000_FWSM_MODE_MASK) ==
+            (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+            return TRUE;
+    } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
+               (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
         return TRUE;
 
     return FALSE;
@@ -7209,7 +7900,6 @@
     E1000_WRITE_REG(hw, CTRL, ctrl);
 }
 
-#if 0
 /***************************************************************************
  *
  * Enables PCI-Express master access.
@@ -7233,7 +7923,6 @@
     ctrl &= ~E1000_CTRL_GIO_MASTER_DISABLE;
     E1000_WRITE_REG(hw, CTRL, ctrl);
 }
-#endif  /*  0  */
 
 /*******************************************************************************
  *
@@ -7299,8 +7988,10 @@
     case e1000_82572:
     case e1000_82573:
     case e1000_80003es2lan:
-        while(timeout) {
-            if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break;
+    case e1000_ich8lan:
+        while (timeout) {
+            if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD)
+                break;
             else msec_delay(1);
             timeout--;
         }
@@ -7340,7 +8031,7 @@
 
     switch (hw->mac_type) {
     default:
-        msec_delay(10);
+        msec_delay_irq(10);
         break;
     case e1000_80003es2lan:
         /* Separate *_CFG_DONE_* bit for each port */
@@ -7523,6 +8214,13 @@
 e1000_check_phy_reset_block(struct e1000_hw *hw)
 {
     uint32_t manc = 0;
+    uint32_t fwsm = 0;
+
+    if (hw->mac_type == e1000_ich8lan) {
+        fwsm = E1000_READ_REG(hw, FWSM);
+        return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS
+                                            : E1000_BLK_PHY_RESET;
+    }
 
     if (hw->mac_type > e1000_82547_rev_2)
         manc = E1000_READ_REG(hw, MANC);
@@ -7549,6 +8247,8 @@
         if((fwsm & E1000_FWSM_MODE_MASK) != 0)
             return TRUE;
         break;
+    case e1000_ich8lan:
+        return TRUE;
     default:
         break;
     }
@@ -7556,4 +8256,846 @@
 }
 
 
+/******************************************************************************
+ * Configure PCI-Ex no-snoop
+ *
+ * hw - Struct containing variables accessed by shared code.
+ * no_snoop - Bitmap of no-snoop events.
+ *
+ * returns: E1000_SUCCESS
+ *
+ *****************************************************************************/
+int32_t
+e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop)
+{
+    uint32_t gcr_reg = 0;
+
+    DEBUGFUNC("e1000_set_pci_ex_no_snoop");
+
+    if (hw->bus_type == e1000_bus_type_unknown)
+        e1000_get_bus_info(hw);
+
+    if (hw->bus_type != e1000_bus_type_pci_express)
+        return E1000_SUCCESS;
+
+    if (no_snoop) {
+        gcr_reg = E1000_READ_REG(hw, GCR);
+        gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL);
+        gcr_reg |= no_snoop;
+        E1000_WRITE_REG(hw, GCR, gcr_reg);
+    }
+    if (hw->mac_type == e1000_ich8lan) {
+        uint32_t ctrl_ext;
+
+        E1000_WRITE_REG(hw, GCR, PCI_EX_82566_SNOOP_ALL);
+
+        ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+        ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+        E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+    }
+
+    return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ *
+ * Get software semaphore FLAG bit (SWFLAG).
+ * SWFLAG is used to synchronize the access to all shared resource between
+ * SW, FW and HW.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+int32_t
+e1000_get_software_flag(struct e1000_hw *hw)
+{
+    int32_t timeout = PHY_CFG_TIMEOUT;
+    uint32_t extcnf_ctrl;
+
+    DEBUGFUNC("e1000_get_software_flag");
+
+    if (hw->mac_type == e1000_ich8lan) {
+        while (timeout) {
+            extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+            extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
+            E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
+
+            extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+            if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
+                break;
+            msec_delay_irq(1);
+            timeout--;
+        }
+
+        if (!timeout) {
+            DEBUGOUT("FW or HW locks the resource too long.\n");
+            return -E1000_ERR_CONFIG;
+        }
+    }
+
+    return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ *
+ * Release software semaphore FLAG bit (SWFLAG).
+ * SWFLAG is used to synchronize the access to all shared resource between
+ * SW, FW and HW.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+void
+e1000_release_software_flag(struct e1000_hw *hw)
+{
+    uint32_t extcnf_ctrl;
+
+    DEBUGFUNC("e1000_release_software_flag");
+
+    if (hw->mac_type == e1000_ich8lan) {
+        extcnf_ctrl= E1000_READ_REG(hw, EXTCNF_CTRL);
+        extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
+        E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
+    }
+
+    return;
+}
+
+/***************************************************************************
+ *
+ * Disable dynamic power down mode in ife PHY.
+ * It can be used to workaround band-gap problem.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+int32_t
+e1000_ife_disable_dynamic_power_down(struct e1000_hw *hw)
+{
+    uint16_t phy_data;
+    int32_t ret_val = E1000_SUCCESS;
+
+    DEBUGFUNC("e1000_ife_disable_dynamic_power_down");
+
+    if (hw->phy_type == e1000_phy_ife) {
+        ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
+        if (ret_val)
+            return ret_val;
+
+        phy_data |=  IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN;
+        ret_val = e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, phy_data);
+    }
+
+    return ret_val;
+}
+
+/***************************************************************************
+ *
+ * Enable dynamic power down mode in ife PHY.
+ * It can be used to workaround band-gap problem.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+int32_t
+e1000_ife_enable_dynamic_power_down(struct e1000_hw *hw)
+{
+    uint16_t phy_data;
+    int32_t ret_val = E1000_SUCCESS;
+
+    DEBUGFUNC("e1000_ife_enable_dynamic_power_down");
+
+    if (hw->phy_type == e1000_phy_ife) {
+        ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
+        if (ret_val)
+            return ret_val;
+
+        phy_data &=  ~IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN;
+        ret_val = e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, phy_data);
+    }
+
+    return ret_val;
+}
+
+/******************************************************************************
+ * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access
+ * register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+int32_t
+e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words,
+                       uint16_t *data)
+{
+    int32_t  error = E1000_SUCCESS;
+    uint32_t flash_bank = 0;
+    uint32_t act_offset = 0;
+    uint32_t bank_offset = 0;
+    uint16_t word = 0;
+    uint16_t i = 0;
+
+    /* We need to know which is the valid flash bank.  In the event
+     * that we didn't allocate eeprom_shadow_ram, we may not be
+     * managing flash_bank.  So it cannot be trusted and needs
+     * to be updated with each read.
+     */
+    /* Value of bit 22 corresponds to the flash bank we're on. */
+    flash_bank = (E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL) ? 1 : 0;
+
+    /* Adjust offset appropriately if we're on bank 1 - adjust for word size */
+    bank_offset = flash_bank * (hw->flash_bank_size * 2);
+
+    error = e1000_get_software_flag(hw);
+    if (error != E1000_SUCCESS)
+        return error;
+
+    for (i = 0; i < words; i++) {
+        if (hw->eeprom_shadow_ram != NULL &&
+            hw->eeprom_shadow_ram[offset+i].modified == TRUE) {
+            data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word;
+        } else {
+            /* The NVM part needs a byte offset, hence * 2 */
+            act_offset = bank_offset + ((offset + i) * 2);
+            error = e1000_read_ich8_word(hw, act_offset, &word);
+            if (error != E1000_SUCCESS)
+                break;
+            data[i] = word;
+        }
+    }
+
+    e1000_release_software_flag(hw);
+
+    return error;
+}
+
+/******************************************************************************
+ * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access
+ * register.  Actually, writes are written to the shadow ram cache in the hw
+ * structure hw->e1000_shadow_ram.  e1000_commit_shadow_ram flushes this to
+ * the NVM, which occurs when the NVM checksum is updated.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to write
+ * words - number of words to write
+ * data - words to write to the EEPROM
+ *****************************************************************************/
+int32_t
+e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words,
+                        uint16_t *data)
+{
+    uint32_t i = 0;
+    int32_t error = E1000_SUCCESS;
+
+    error = e1000_get_software_flag(hw);
+    if (error != E1000_SUCCESS)
+        return error;
+
+    /* A driver can write to the NVM only if it has eeprom_shadow_ram
+     * allocated.  Subsequent reads to the modified words are read from
+     * this cached structure as well.  Writes will only go into this
+     * cached structure unless it's followed by a call to
+     * e1000_update_eeprom_checksum() where it will commit the changes
+     * and clear the "modified" field.
+     */
+    if (hw->eeprom_shadow_ram != NULL) {
+        for (i = 0; i < words; i++) {
+            if ((offset + i) < E1000_SHADOW_RAM_WORDS) {
+                hw->eeprom_shadow_ram[offset+i].modified = TRUE;
+                hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i];
+            } else {
+                error = -E1000_ERR_EEPROM;
+                break;
+            }
+        }
+    } else {
+        /* Drivers have the option to not allocate eeprom_shadow_ram as long
+         * as they don't perform any NVM writes.  An attempt in doing so
+         * will result in this error.
+         */
+        error = -E1000_ERR_EEPROM;
+    }
+
+    e1000_release_software_flag(hw);
+
+    return error;
+}
+
+/******************************************************************************
+ * This function does initial flash setup so that a new read/write/erase cycle
+ * can be started.
+ *
+ * hw - The pointer to the hw structure
+ ****************************************************************************/
+int32_t
+e1000_ich8_cycle_init(struct e1000_hw *hw)
+{
+    union ich8_hws_flash_status hsfsts;
+    int32_t error = E1000_ERR_EEPROM;
+    int32_t i     = 0;
+
+    DEBUGFUNC("e1000_ich8_cycle_init");
+
+    hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+
+    /* May be check the Flash Des Valid bit in Hw status */
+    if (hsfsts.hsf_status.fldesvalid == 0) {
+        DEBUGOUT("Flash descriptor invalid.  SW Sequencing must be used.");
+        return error;
+    }
+
+    /* Clear FCERR in Hw status by writing 1 */
+    /* Clear DAEL in Hw status by writing a 1 */
+    hsfsts.hsf_status.flcerr = 1;
+    hsfsts.hsf_status.dael = 1;
+
+    E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval);
+
+    /* Either we should have a hardware SPI cycle in progress bit to check
+     * against, in order to start a new cycle or FDONE bit should be changed
+     * in the hardware so that it is 1 after harware reset, which can then be
+     * used as an indication whether a cycle is in progress or has been
+     * completed .. we should also have some software semaphore mechanism to
+     * guard FDONE or the cycle in progress bit so that two threads access to
+     * those bits can be sequentiallized or a way so that 2 threads dont
+     * start the cycle at the same time */
+
+    if (hsfsts.hsf_status.flcinprog == 0) {
+        /* There is no cycle running at present, so we can start a cycle */
+        /* Begin by setting Flash Cycle Done. */
+        hsfsts.hsf_status.flcdone = 1;
+        E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval);
+        error = E1000_SUCCESS;
+    } else {
+        /* otherwise poll for sometime so the current cycle has a chance
+         * to end before giving up. */
+        for (i = 0; i < ICH8_FLASH_COMMAND_TIMEOUT; i++) {
+            hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+            if (hsfsts.hsf_status.flcinprog == 0) {
+                error = E1000_SUCCESS;
+                break;
+            }
+            udelay(1);
+        }
+        if (error == E1000_SUCCESS) {
+            /* Successful in waiting for previous cycle to timeout,
+             * now set the Flash Cycle Done. */
+            hsfsts.hsf_status.flcdone = 1;
+            E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval);
+        } else {
+            DEBUGOUT("Flash controller busy, cannot get access");
+        }
+    }
+    return error;
+}
+
+/******************************************************************************
+ * This function starts a flash cycle and waits for its completion
+ *
+ * hw - The pointer to the hw structure
+ ****************************************************************************/
+int32_t
+e1000_ich8_flash_cycle(struct e1000_hw *hw, uint32_t timeout)
+{
+    union ich8_hws_flash_ctrl hsflctl;
+    union ich8_hws_flash_status hsfsts;
+    int32_t error = E1000_ERR_EEPROM;
+    uint32_t i = 0;
+
+    /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
+    hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+    hsflctl.hsf_ctrl.flcgo = 1;
+    E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+    /* wait till FDONE bit is set to 1 */
+    do {
+        hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+        if (hsfsts.hsf_status.flcdone == 1)
+            break;
+        udelay(1);
+        i++;
+    } while (i < timeout);
+    if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) {
+        error = E1000_SUCCESS;
+    }
+    return error;
+}
+
+/******************************************************************************
+ * Reads a byte or word from the NVM using the ICH8 flash access registers.
+ *
+ * hw - The pointer to the hw structure
+ * index - The index of the byte or word to read.
+ * size - Size of data to read, 1=byte 2=word
+ * data - Pointer to the word to store the value read.
+ *****************************************************************************/
+int32_t
+e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index,
+                     uint32_t size, uint16_t* data)
+{
+    union ich8_hws_flash_status hsfsts;
+    union ich8_hws_flash_ctrl hsflctl;
+    uint32_t flash_linear_address;
+    uint32_t flash_data = 0;
+    int32_t error = -E1000_ERR_EEPROM;
+    int32_t count = 0;
+
+    DEBUGFUNC("e1000_read_ich8_data");
+
+    if (size < 1  || size > 2 || data == 0x0 ||
+        index > ICH8_FLASH_LINEAR_ADDR_MASK)
+        return error;
+
+    flash_linear_address = (ICH8_FLASH_LINEAR_ADDR_MASK & index) +
+                           hw->flash_base_addr;
+
+    do {
+        udelay(1);
+        /* Steps */
+        error = e1000_ich8_cycle_init(hw);
+        if (error != E1000_SUCCESS)
+            break;
+
+        hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+        /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+        hsflctl.hsf_ctrl.fldbcount = size - 1;
+        hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_READ;
+        E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+        /* Write the last 24 bits of index into Flash Linear address field in
+         * Flash Address */
+        /* TODO: TBD maybe check the index against the size of flash */
+
+        E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address);
+
+        error = e1000_ich8_flash_cycle(hw, ICH8_FLASH_COMMAND_TIMEOUT);
+
+        /* Check if FCERR is set to 1, if set to 1, clear it and try the whole
+         * sequence a few more times, else read in (shift in) the Flash Data0,
+         * the order is least significant byte first msb to lsb */
+        if (error == E1000_SUCCESS) {
+            flash_data = E1000_READ_ICH8_REG(hw, ICH8_FLASH_FDATA0);
+            if (size == 1) {
+                *data = (uint8_t)(flash_data & 0x000000FF);
+            } else if (size == 2) {
+                *data = (uint16_t)(flash_data & 0x0000FFFF);
+            }
+            break;
+        } else {
+            /* If we've gotten here, then things are probably completely hosed,
+             * but if the error condition is detected, it won't hurt to give
+             * it another try...ICH8_FLASH_CYCLE_REPEAT_COUNT times.
+             */
+            hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+            if (hsfsts.hsf_status.flcerr == 1) {
+                /* Repeat for some time before giving up. */
+                continue;
+            } else if (hsfsts.hsf_status.flcdone == 0) {
+                DEBUGOUT("Timeout error - flash cycle did not complete.");
+                break;
+            }
+        }
+    } while (count++ < ICH8_FLASH_CYCLE_REPEAT_COUNT);
+
+    return error;
+}
+
+/******************************************************************************
+ * Writes One /two bytes to the NVM using the ICH8 flash access registers.
+ *
+ * hw - The pointer to the hw structure
+ * index - The index of the byte/word to read.
+ * size - Size of data to read, 1=byte 2=word
+ * data - The byte(s) to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_write_ich8_data(struct e1000_hw *hw, uint32_t index, uint32_t size,
+                      uint16_t data)
+{
+    union ich8_hws_flash_status hsfsts;
+    union ich8_hws_flash_ctrl hsflctl;
+    uint32_t flash_linear_address;
+    uint32_t flash_data = 0;
+    int32_t error = -E1000_ERR_EEPROM;
+    int32_t count = 0;
+
+    DEBUGFUNC("e1000_write_ich8_data");
+
+    if (size < 1  || size > 2 || data > size * 0xff ||
+        index > ICH8_FLASH_LINEAR_ADDR_MASK)
+        return error;
+
+    flash_linear_address = (ICH8_FLASH_LINEAR_ADDR_MASK & index) +
+                           hw->flash_base_addr;
+
+    do {
+        udelay(1);
+        /* Steps */
+        error = e1000_ich8_cycle_init(hw);
+        if (error != E1000_SUCCESS)
+            break;
+
+        hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+        /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+        hsflctl.hsf_ctrl.fldbcount = size -1;
+        hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_WRITE;
+        E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+        /* Write the last 24 bits of index into Flash Linear address field in
+         * Flash Address */
+        E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address);
+
+        if (size == 1)
+            flash_data = (uint32_t)data & 0x00FF;
+        else
+            flash_data = (uint32_t)data;
+
+        E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FDATA0, flash_data);
+
+        /* check if FCERR is set to 1 , if set to 1, clear it and try the whole
+         * sequence a few more times else done */
+        error = e1000_ich8_flash_cycle(hw, ICH8_FLASH_COMMAND_TIMEOUT);
+        if (error == E1000_SUCCESS) {
+            break;
+        } else {
+            /* If we're here, then things are most likely completely hosed,
+             * but if the error condition is detected, it won't hurt to give
+             * it another try...ICH8_FLASH_CYCLE_REPEAT_COUNT times.
+             */
+            hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+            if (hsfsts.hsf_status.flcerr == 1) {
+                /* Repeat for some time before giving up. */
+                continue;
+            } else if (hsfsts.hsf_status.flcdone == 0) {
+                DEBUGOUT("Timeout error - flash cycle did not complete.");
+                break;
+            }
+        }
+    } while (count++ < ICH8_FLASH_CYCLE_REPEAT_COUNT);
+
+    return error;
+}
+
+/******************************************************************************
+ * Reads a single byte from the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The index of the byte to read.
+ * data - Pointer to a byte to store the value read.
+ *****************************************************************************/
+int32_t
+e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t* data)
+{
+    int32_t status = E1000_SUCCESS;
+    uint16_t word = 0;
+
+    status = e1000_read_ich8_data(hw, index, 1, &word);
+    if (status == E1000_SUCCESS) {
+        *data = (uint8_t)word;
+    }
+
+    return status;
+}
+
+/******************************************************************************
+ * Writes a single byte to the NVM using the ICH8 flash access registers.
+ * Performs verification by reading back the value and then going through
+ * a retry algorithm before giving up.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The index of the byte to write.
+ * byte - The byte to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t byte)
+{
+    int32_t error = E1000_SUCCESS;
+    int32_t program_retries;
+    uint8_t temp_byte;
+
+    e1000_write_ich8_byte(hw, index, byte);
+    udelay(100);
+
+    for (program_retries = 0; program_retries < 100; program_retries++) {
+        e1000_read_ich8_byte(hw, index, &temp_byte);
+        if (temp_byte == byte)
+            break;
+        udelay(10);
+        e1000_write_ich8_byte(hw, index, byte);
+        udelay(100);
+    }
+    if (program_retries == 100)
+        error = E1000_ERR_EEPROM;
+
+    return error;
+}
+
+/******************************************************************************
+ * Writes a single byte to the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The index of the byte to read.
+ * data - The byte to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t data)
+{
+    int32_t status = E1000_SUCCESS;
+    uint16_t word = (uint16_t)data;
+
+    status = e1000_write_ich8_data(hw, index, 1, word);
+
+    return status;
+}
+
+/******************************************************************************
+ * Reads a word from the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The starting byte index of the word to read.
+ * data - Pointer to a word to store the value read.
+ *****************************************************************************/
+int32_t
+e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t *data)
+{
+    int32_t status = E1000_SUCCESS;
+    status = e1000_read_ich8_data(hw, index, 2, data);
+    return status;
+}
+
+/******************************************************************************
+ * Writes a word to the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The starting byte index of the word to read.
+ * data - The word to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_write_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t data)
+{
+    int32_t status = E1000_SUCCESS;
+    status = e1000_write_ich8_data(hw, index, 2, data);
+    return status;
+}
+
+/******************************************************************************
+ * Erases the bank specified. Each bank is a 4k block. Segments are 0 based.
+ * segment N is 4096 * N + flash_reg_addr.
+ *
+ * hw - pointer to e1000_hw structure
+ * segment - 0 for first segment, 1 for second segment, etc.
+ *****************************************************************************/
+int32_t
+e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t segment)
+{
+    union ich8_hws_flash_status hsfsts;
+    union ich8_hws_flash_ctrl hsflctl;
+    uint32_t flash_linear_address;
+    int32_t  count = 0;
+    int32_t  error = E1000_ERR_EEPROM;
+    int32_t  iteration, seg_size;
+    int32_t  sector_size;
+    int32_t  j = 0;
+    int32_t  error_flag = 0;
+
+    hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+
+    /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */
+    /* 00: The Hw sector is 256 bytes, hence we need to erase 16
+     *     consecutive sectors.  The start index for the nth Hw sector can be
+     *     calculated as = segment * 4096 + n * 256
+     * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
+     *     The start index for the nth Hw sector can be calculated
+     *     as = segment * 4096
+     * 10: Error condition
+     * 11: The Hw sector size is much bigger than the size asked to
+     *     erase...error condition */
+    if (hsfsts.hsf_status.berasesz == 0x0) {
+        /* Hw sector size 256 */
+        sector_size = seg_size = ICH8_FLASH_SEG_SIZE_256;
+        iteration = ICH8_FLASH_SECTOR_SIZE / ICH8_FLASH_SEG_SIZE_256;
+    } else if (hsfsts.hsf_status.berasesz == 0x1) {
+        sector_size = seg_size = ICH8_FLASH_SEG_SIZE_4K;
+        iteration = 1;
+    } else if (hsfsts.hsf_status.berasesz == 0x3) {
+        sector_size = seg_size = ICH8_FLASH_SEG_SIZE_64K;
+        iteration = 1;
+    } else {
+        return error;
+    }
+
+    for (j = 0; j < iteration ; j++) {
+        do {
+            count++;
+            /* Steps */
+            error = e1000_ich8_cycle_init(hw);
+            if (error != E1000_SUCCESS) {
+                error_flag = 1;
+                break;
+            }
+
+            /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash
+             * Control */
+            hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+            hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_ERASE;
+            E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+            /* Write the last 24 bits of an index within the block into Flash
+             * Linear address field in Flash Address.  This probably needs to
+             * be calculated here based off the on-chip segment size and the
+             * software segment size assumed (4K) */
+            /* TBD */
+            flash_linear_address = segment * sector_size + j * seg_size;
+            flash_linear_address &= ICH8_FLASH_LINEAR_ADDR_MASK;
+            flash_linear_address += hw->flash_base_addr;
+
+            E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address);
+
+            error = e1000_ich8_flash_cycle(hw, 1000000);
+            /* Check if FCERR is set to 1.  If 1, clear it and try the whole
+             * sequence a few more times else Done */
+            if (error == E1000_SUCCESS) {
+                break;
+            } else {
+                hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+                if (hsfsts.hsf_status.flcerr == 1) {
+                    /* repeat for some time before giving up */
+                    continue;
+                } else if (hsfsts.hsf_status.flcdone == 0) {
+                    error_flag = 1;
+                    break;
+                }
+            }
+        } while ((count < ICH8_FLASH_CYCLE_REPEAT_COUNT) && !error_flag);
+        if (error_flag == 1)
+            break;
+    }
+    if (error_flag != 1)
+        error = E1000_SUCCESS;
+    return error;
+}
+
+/******************************************************************************
+ *
+ * Reverse duplex setting without breaking the link.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ *****************************************************************************/
+int32_t
+e1000_duplex_reversal(struct e1000_hw *hw)
+{
+    int32_t ret_val;
+    uint16_t phy_data;
+
+    if (hw->phy_type != e1000_phy_igp_3)
+        return E1000_SUCCESS;
+
+    ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+    if (ret_val)
+        return ret_val;
+
+    phy_data ^= MII_CR_FULL_DUPLEX;
+
+    ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+    if (ret_val)
+        return ret_val;
+
+    ret_val = e1000_read_phy_reg(hw, IGP3E1000_PHY_MISC_CTRL, &phy_data);
+    if (ret_val)
+        return ret_val;
+
+    phy_data |= IGP3_PHY_MISC_DUPLEX_MANUAL_SET;
+    ret_val = e1000_write_phy_reg(hw, IGP3E1000_PHY_MISC_CTRL, phy_data);
+
+    return ret_val;
+}
+
+int32_t
+e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw,
+                                      uint32_t cnf_base_addr, uint32_t cnf_size)
+{
+    uint32_t ret_val = E1000_SUCCESS;
+    uint16_t word_addr, reg_data, reg_addr;
+    uint16_t i;
+
+    /* cnf_base_addr is in DWORD */
+    word_addr = (uint16_t)(cnf_base_addr << 1);
+
+    /* cnf_size is returned in size of dwords */
+    for (i = 0; i < cnf_size; i++) {
+        ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, &reg_data);
+        if (ret_val)
+            return ret_val;
+
+        ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, &reg_addr);
+        if (ret_val)
+            return ret_val;
+
+        ret_val = e1000_get_software_flag(hw);
+        if (ret_val != E1000_SUCCESS)
+            return ret_val;
+
+        ret_val = e1000_write_phy_reg_ex(hw, (uint32_t)reg_addr, reg_data);
+
+        e1000_release_software_flag(hw);
+    }
+
+    return ret_val;
+}
+
+
+int32_t
+e1000_init_lcd_from_nvm(struct e1000_hw *hw)
+{
+    uint32_t reg_data, cnf_base_addr, cnf_size, ret_val, loop;
+
+    if (hw->phy_type != e1000_phy_igp_3)
+          return E1000_SUCCESS;
+
+    /* Check if SW needs configure the PHY */
+    reg_data = E1000_READ_REG(hw, FEXTNVM);
+    if (!(reg_data & FEXTNVM_SW_CONFIG))
+        return E1000_SUCCESS;
+
+    /* Wait for basic configuration completes before proceeding*/
+    loop = 0;
+    do {
+        reg_data = E1000_READ_REG(hw, STATUS) & E1000_STATUS_LAN_INIT_DONE;
+        udelay(100);
+        loop++;
+    } while ((!reg_data) && (loop < 50));
+
+    /* Clear the Init Done bit for the next init event */
+    reg_data = E1000_READ_REG(hw, STATUS);
+    reg_data &= ~E1000_STATUS_LAN_INIT_DONE;
+    E1000_WRITE_REG(hw, STATUS, reg_data);
+
+    /* Make sure HW does not configure LCD from PHY extended configuration
+       before SW configuration */
+    reg_data = E1000_READ_REG(hw, EXTCNF_CTRL);
+    if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) {
+        reg_data = E1000_READ_REG(hw, EXTCNF_SIZE);
+        cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH;
+        cnf_size >>= 16;
+        if (cnf_size) {
+            reg_data = E1000_READ_REG(hw, EXTCNF_CTRL);
+            cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER;
+            /* cnf_base_addr is in DWORD */
+            cnf_base_addr >>= 16;
+
+            /* Configure LCD from extended configuration region. */
+            ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr,
+                                                            cnf_size);
+            if (ret_val)
+                return ret_val;
+        }
+    }
+
+    return E1000_SUCCESS;
+}
+
+
 
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index 467c9ed..f9341e3 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -62,6 +62,7 @@
     e1000_82572,
     e1000_82573,
     e1000_80003es2lan,
+    e1000_ich8lan,
     e1000_num_macs
 } e1000_mac_type;
 
@@ -70,6 +71,7 @@
     e1000_eeprom_spi,
     e1000_eeprom_microwire,
     e1000_eeprom_flash,
+    e1000_eeprom_ich8,
     e1000_eeprom_none, /* No NVM support */
     e1000_num_eeprom_types
 } e1000_eeprom_type;
@@ -98,6 +100,11 @@
     e1000_fc_default = 0xFF
 } e1000_fc_type;
 
+struct e1000_shadow_ram {
+    uint16_t    eeprom_word;
+    boolean_t   modified;
+};
+
 /* PCI bus types */
 typedef enum {
     e1000_bus_type_unknown = 0,
@@ -218,6 +225,8 @@
     e1000_phy_igp,
     e1000_phy_igp_2,
     e1000_phy_gg82563,
+    e1000_phy_igp_3,
+    e1000_phy_ife,
     e1000_phy_undefined = 0xFF
 } e1000_phy_type;
 
@@ -313,6 +322,10 @@
 int32_t e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data);
 int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
 int32_t e1000_phy_reset(struct e1000_hw *hw);
+void e1000_phy_powerdown_workaround(struct e1000_hw *hw);
+int32_t e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw);
+int32_t e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, uint32_t cnf_base_addr, uint32_t cnf_size);
+int32_t e1000_init_lcd_from_nvm(struct e1000_hw *hw);
 int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
 int32_t e1000_validate_mdi_setting(struct e1000_hw *hw);
 int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data);
@@ -331,6 +344,7 @@
 #define E1000_MNG_DHCP_COOKIE_OFFSET	0x6F0   /* Cookie offset */
 #define E1000_MNG_DHCP_COOKIE_LENGTH	0x10    /* Cookie length */
 #define E1000_MNG_IAMT_MODE		0x3
+#define E1000_MNG_ICH_IAMT_MODE         0x2
 #define E1000_IAMT_SIGNATURE            0x544D4149 /* Intel(R) Active Management Technology signature */
 
 #define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
@@ -388,6 +402,8 @@
 int32_t e1000_read_mac_addr(struct e1000_hw * hw);
 int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
 void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
+void e1000_release_software_flag(struct e1000_hw *hw);
+int32_t e1000_get_software_flag(struct e1000_hw *hw);
 
 /* Filters (multicast, vlan, receive) */
 void e1000_mc_addr_list_update(struct e1000_hw *hw, uint8_t * mc_addr_list, uint32_t mc_addr_count, uint32_t pad, uint32_t rar_used_count);
@@ -401,6 +417,7 @@
 int32_t e1000_cleanup_led(struct e1000_hw *hw);
 int32_t e1000_led_on(struct e1000_hw *hw);
 int32_t e1000_led_off(struct e1000_hw *hw);
+int32_t e1000_blink_led_start(struct e1000_hw *hw);
 
 /* Adaptive IFS Functions */
 
@@ -422,6 +439,29 @@
 int32_t e1000_get_software_semaphore(struct e1000_hw *hw);
 void e1000_release_software_semaphore(struct e1000_hw *hw);
 int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
+int32_t e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop);
+
+int32_t e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index,
+                             uint8_t *data);
+int32_t e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index,
+                                     uint8_t byte);
+int32_t e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index,
+                              uint8_t byte);
+int32_t e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index,
+                             uint16_t *data);
+int32_t e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index,
+                             uint32_t size, uint16_t *data);
+int32_t e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset,
+                               uint16_t words, uint16_t *data);
+int32_t e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset,
+                                uint16_t words, uint16_t *data);
+int32_t e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t segment);
+
+
+#define E1000_READ_REG_IO(a, reg) \
+    e1000_read_reg_io((a), E1000_##reg)
+#define E1000_WRITE_REG_IO(a, reg, val) \
+    e1000_write_reg_io((a), E1000_##reg, val)
 
 /* PCI Device IDs */
 #define E1000_DEV_ID_82542               0x1000
@@ -446,6 +486,7 @@
 #define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D
 #define E1000_DEV_ID_82541EI             0x1013
 #define E1000_DEV_ID_82541EI_MOBILE      0x1018
+#define E1000_DEV_ID_82541ER_LOM         0x1014
 #define E1000_DEV_ID_82541ER             0x1078
 #define E1000_DEV_ID_82547GI             0x1075
 #define E1000_DEV_ID_82541GI             0x1076
@@ -457,18 +498,28 @@
 #define E1000_DEV_ID_82546GB_PCIE        0x108A
 #define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
 #define E1000_DEV_ID_82547EI             0x1019
+#define E1000_DEV_ID_82547EI_MOBILE      0x101A
 #define E1000_DEV_ID_82571EB_COPPER      0x105E
 #define E1000_DEV_ID_82571EB_FIBER       0x105F
 #define E1000_DEV_ID_82571EB_SERDES      0x1060
 #define E1000_DEV_ID_82572EI_COPPER      0x107D
 #define E1000_DEV_ID_82572EI_FIBER       0x107E
 #define E1000_DEV_ID_82572EI_SERDES      0x107F
+#define E1000_DEV_ID_82572EI             0x10B9
 #define E1000_DEV_ID_82573E              0x108B
 #define E1000_DEV_ID_82573E_IAMT         0x108C
 #define E1000_DEV_ID_82573L              0x109A
 #define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
 #define E1000_DEV_ID_80003ES2LAN_COPPER_DPT     0x1096
 #define E1000_DEV_ID_80003ES2LAN_SERDES_DPT     0x1098
+#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT     0x10BA
+#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT     0x10BB
+
+#define E1000_DEV_ID_ICH8_IGP_M_AMT      0x1049
+#define E1000_DEV_ID_ICH8_IGP_AMT        0x104A
+#define E1000_DEV_ID_ICH8_IGP_C          0x104B
+#define E1000_DEV_ID_ICH8_IFE            0x104C
+#define E1000_DEV_ID_ICH8_IGP_M          0x104D
 
 
 #define NODE_ADDRESS_SIZE 6
@@ -539,6 +590,14 @@
     E1000_IMS_RXSEQ  |    \
     E1000_IMS_LSC)
 
+/* Additional interrupts need to be handled for e1000_ich8lan:
+    DSW = The FW changed the status of the DISSW bit in FWSM
+    PHYINT = The LAN connected device generates an interrupt
+    EPRST = Manageability reset event */
+#define IMS_ICH8LAN_ENABLE_MASK (\
+    E1000_IMS_DSW   | \
+    E1000_IMS_PHYINT | \
+    E1000_IMS_EPRST)
 
 /* Number of high/low register pairs in the RAR. The RAR (Receive Address
  * Registers) holds the directed and multicast addresses that we monitor. We
@@ -546,6 +605,7 @@
  * E1000_RAR_ENTRIES - 1 multicast addresses.
  */
 #define E1000_RAR_ENTRIES 15
+#define E1000_RAR_ENTRIES_ICH8LAN  7
 
 #define MIN_NUMBER_OF_DESCRIPTORS 8
 #define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8
@@ -767,6 +827,9 @@
 #define E1000_MC_TBL_SIZE          128  /* Multicast Filter Table (4096 bits) */
 #define E1000_VLAN_FILTER_TBL_SIZE 128  /* VLAN Filter Table (4096 bits) */
 
+#define E1000_NUM_UNICAST_ICH8LAN  7
+#define E1000_MC_TBL_SIZE_ICH8LAN  32
+
 
 /* Receive Address Register */
 struct e1000_rar {
@@ -776,6 +839,7 @@
 
 /* Number of entries in the Multicast Table Array (MTA). */
 #define E1000_NUM_MTA_REGISTERS 128
+#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32
 
 /* IPv4 Address Table Entry */
 struct e1000_ipv4_at_entry {
@@ -786,6 +850,7 @@
 /* Four wakeup IP addresses are supported */
 #define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4
 #define E1000_IP4AT_SIZE                  E1000_WAKEUP_IP_ADDRESS_COUNT_MAX
+#define E1000_IP4AT_SIZE_ICH8LAN          3
 #define E1000_IP6AT_SIZE                  1
 
 /* IPv6 Address Table Entry */
@@ -844,6 +909,7 @@
 #define E1000_FLA      0x0001C  /* Flash Access - RW */
 #define E1000_MDIC     0x00020  /* MDI Control - RW */
 #define E1000_SCTL     0x00024  /* SerDes Control - RW */
+#define E1000_FEXTNVM  0x00028  /* Future Extended NVM register */
 #define E1000_FCAL     0x00028  /* Flow Control Address Low - RW */
 #define E1000_FCAH     0x0002C  /* Flow Control Address High -RW */
 #define E1000_FCT      0x00030  /* Flow Control Type - RW */
@@ -872,6 +938,8 @@
 #define E1000_LEDCTL   0x00E00  /* LED Control - RW */
 #define E1000_EXTCNF_CTRL  0x00F00  /* Extended Configuration Control */
 #define E1000_EXTCNF_SIZE  0x00F08  /* Extended Configuration Size */
+#define E1000_PHY_CTRL     0x00F10  /* PHY Control Register in CSR */
+#define FEXTNVM_SW_CONFIG  0x0001
 #define E1000_PBA      0x01000  /* Packet Buffer Allocation - RW */
 #define E1000_PBS      0x01008  /* Packet Buffer Size */
 #define E1000_EEMNGCTL 0x01010  /* MNG EEprom Control */
@@ -899,11 +967,13 @@
 #define E1000_RDH0     E1000_RDH   /* RX Desc Head (0) - RW */
 #define E1000_RDT0     E1000_RDT   /* RX Desc Tail (0) - RW */
 #define E1000_RDTR0    E1000_RDTR  /* RX Delay Timer (0) - RW */
-#define E1000_RXDCTL   0x02828  /* RX Descriptor Control - RW */
+#define E1000_RXDCTL   0x02828  /* RX Descriptor Control queue 0 - RW */
+#define E1000_RXDCTL1  0x02928  /* RX Descriptor Control queue 1 - RW */
 #define E1000_RADV     0x0282C  /* RX Interrupt Absolute Delay Timer - RW */
 #define E1000_RSRPD    0x02C00  /* RX Small Packet Detect - RW */
 #define E1000_RAID     0x02C08  /* Receive Ack Interrupt Delay - RW */
 #define E1000_TXDMAC   0x03000  /* TX DMA Control - RW */
+#define E1000_KABGTXD  0x03004  /* AFE Band Gap Transmit Ref Data */
 #define E1000_TDFH     0x03410  /* TX Data FIFO Head - RW */
 #define E1000_TDFT     0x03418  /* TX Data FIFO Tail - RW */
 #define E1000_TDFHS    0x03420  /* TX Data FIFO Head Saved - RW */
@@ -1050,6 +1120,7 @@
 #define E1000_82542_FLA      E1000_FLA
 #define E1000_82542_MDIC     E1000_MDIC
 #define E1000_82542_SCTL     E1000_SCTL
+#define E1000_82542_FEXTNVM  E1000_FEXTNVM
 #define E1000_82542_FCAL     E1000_FCAL
 #define E1000_82542_FCAH     E1000_FCAH
 #define E1000_82542_FCT      E1000_FCT
@@ -1073,6 +1144,19 @@
 #define E1000_82542_RDLEN0   E1000_82542_RDLEN
 #define E1000_82542_RDH0     E1000_82542_RDH
 #define E1000_82542_RDT0     E1000_82542_RDT
+#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication
+                                                       * RX Control - RW */
+#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8))
+#define E1000_82542_RDBAH3   0x02B04 /* RX Desc Base High Queue 3 - RW */
+#define E1000_82542_RDBAL3   0x02B00 /* RX Desc Low Queue 3 - RW */
+#define E1000_82542_RDLEN3   0x02B08 /* RX Desc Length Queue 3 - RW */
+#define E1000_82542_RDH3     0x02B10 /* RX Desc Head Queue 3 - RW */
+#define E1000_82542_RDT3     0x02B18 /* RX Desc Tail Queue 3 - RW */
+#define E1000_82542_RDBAL2   0x02A00 /* RX Desc Base Low Queue 2 - RW */
+#define E1000_82542_RDBAH2   0x02A04 /* RX Desc Base High Queue 2 - RW */
+#define E1000_82542_RDLEN2   0x02A08 /* RX Desc Length Queue 2 - RW */
+#define E1000_82542_RDH2     0x02A10 /* RX Desc Head Queue 2 - RW */
+#define E1000_82542_RDT2     0x02A18 /* RX Desc Tail Queue 2 - RW */
 #define E1000_82542_RDTR1    0x00130
 #define E1000_82542_RDBAL1   0x00138
 #define E1000_82542_RDBAH1   0x0013C
@@ -1110,11 +1194,14 @@
 #define E1000_82542_FLOP     E1000_FLOP
 #define E1000_82542_EXTCNF_CTRL  E1000_EXTCNF_CTRL
 #define E1000_82542_EXTCNF_SIZE  E1000_EXTCNF_SIZE
+#define E1000_82542_PHY_CTRL E1000_PHY_CTRL
 #define E1000_82542_ERT      E1000_ERT
 #define E1000_82542_RXDCTL   E1000_RXDCTL
+#define E1000_82542_RXDCTL1  E1000_RXDCTL1
 #define E1000_82542_RADV     E1000_RADV
 #define E1000_82542_RSRPD    E1000_RSRPD
 #define E1000_82542_TXDMAC   E1000_TXDMAC
+#define E1000_82542_KABGTXD  E1000_KABGTXD
 #define E1000_82542_TDFHS    E1000_TDFHS
 #define E1000_82542_TDFTS    E1000_TDFTS
 #define E1000_82542_TDFPC    E1000_TDFPC
@@ -1310,13 +1397,16 @@
 
 /* Structure containing variables used by the shared code (e1000_hw.c) */
 struct e1000_hw {
-    uint8_t __iomem *hw_addr;
+    uint8_t *hw_addr;
     uint8_t *flash_address;
     e1000_mac_type mac_type;
     e1000_phy_type phy_type;
     uint32_t phy_init_script;
     e1000_media_type media_type;
     void *back;
+    struct e1000_shadow_ram *eeprom_shadow_ram;
+    uint32_t flash_bank_size;
+    uint32_t flash_base_addr;
     e1000_fc_type fc;
     e1000_bus_speed bus_speed;
     e1000_bus_width bus_width;
@@ -1328,6 +1418,7 @@
     uint32_t asf_firmware_present;
     uint32_t eeprom_semaphore_present;
     uint32_t swfw_sync_present;
+    uint32_t swfwhw_semaphore_present;
     unsigned long io_base;
     uint32_t phy_id;
     uint32_t phy_revision;
@@ -1387,6 +1478,7 @@
     boolean_t in_ifs_mode;
     boolean_t mng_reg_access_disabled;
     boolean_t leave_av_bit_off;
+    boolean_t kmrn_lock_loss_workaround_disabled;
 };
 
 
@@ -1435,6 +1527,7 @@
 #define E1000_CTRL_RTE      0x20000000  /* Routing tag enable */
 #define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
 #define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
+#define E1000_CTRL_SW2FW_INT 0x02000000  /* Initiate an interrupt to manageability engine */
 
 /* Device Status */
 #define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
@@ -1449,6 +1542,8 @@
 #define E1000_STATUS_SPEED_10   0x00000000      /* Speed 10Mb/s */
 #define E1000_STATUS_SPEED_100  0x00000040      /* Speed 100Mb/s */
 #define E1000_STATUS_SPEED_1000 0x00000080      /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200   /* Lan Init Completion
+                                                   by EEPROM/Flash */
 #define E1000_STATUS_ASDV       0x00000300      /* Auto speed detect value */
 #define E1000_STATUS_DOCK_CI    0x00000800      /* Change in Dock/Undock state. Clear on write '0'. */
 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
@@ -1506,6 +1601,10 @@
 #define E1000_STM_OPCODE     0xDB00
 #define E1000_HICR_FW_RESET  0xC0
 
+#define E1000_SHADOW_RAM_WORDS     2048
+#define E1000_ICH8_NVM_SIG_WORD    0x13
+#define E1000_ICH8_NVM_SIG_MASK    0xC0
+
 /* EEPROM Read */
 #define E1000_EERD_START      0x00000001 /* Start Read */
 #define E1000_EERD_DONE       0x00000010 /* Read Done */
@@ -1551,7 +1650,6 @@
 #define E1000_CTRL_EXT_WR_WMARK_320   0x01000000
 #define E1000_CTRL_EXT_WR_WMARK_384   0x02000000
 #define E1000_CTRL_EXT_WR_WMARK_448   0x03000000
-#define E1000_CTRL_EXT_CANC           0x04000000  /* Interrupt delay cancellation */
 #define E1000_CTRL_EXT_DRV_LOAD       0x10000000  /* Driver loaded bit for FW */
 #define E1000_CTRL_EXT_IAME           0x08000000  /* Interrupt acknowledge Auto-mask */
 #define E1000_CTRL_EXT_INT_TIMER_CLR  0x20000000  /* Clear Interrupt timers after IMS clear */
@@ -1591,12 +1689,31 @@
 #define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS   0x00000800
 
 /* In-Band Control */
+#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT    0x00000500
 #define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING  0x00000010
 
 /* Half-Duplex Control */
 #define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004
 #define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT  0x00000000
 
+#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL       0x0000001E
+
+#define E1000_KUMCTRLSTA_DIAG_FELPBK           0x2000
+#define E1000_KUMCTRLSTA_DIAG_NELPBK           0x1000
+
+#define E1000_KUMCTRLSTA_K0S_100_EN            0x2000
+#define E1000_KUMCTRLSTA_K0S_GBE_EN            0x1000
+#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK   0x0003
+
+#define E1000_KABGTXD_BGSQLBIAS                0x00050000
+
+#define E1000_PHY_CTRL_SPD_EN                  0x00000001
+#define E1000_PHY_CTRL_D0A_LPLU                0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU             0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE      0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE             0x00000040
+#define E1000_PHY_CTRL_B2B_EN                  0x00000080
+
 /* LED Control */
 #define E1000_LEDCTL_LED0_MODE_MASK       0x0000000F
 #define E1000_LEDCTL_LED0_MODE_SHIFT      0
@@ -1666,6 +1783,9 @@
 #define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
 #define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
 #define E1000_ICR_ALL_PARITY    0x03F00000 /* all parity error bits */
+#define E1000_ICR_DSW           0x00000020 /* FW changed the status of DISSW bit in the FWSM */
+#define E1000_ICR_PHYINT        0x00001000 /* LAN connected device generates an interrupt */
+#define E1000_ICR_EPRST         0x00100000 /* ME handware reset occurs */
 
 /* Interrupt Cause Set */
 #define E1000_ICS_TXDW      E1000_ICR_TXDW      /* Transmit desc written back */
@@ -1692,6 +1812,9 @@
 #define E1000_ICS_PB_PAR        E1000_ICR_PB_PAR        /* packet buffer parity error */
 #define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
 #define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICS_DSW       E1000_ICR_DSW
+#define E1000_ICS_PHYINT    E1000_ICR_PHYINT
+#define E1000_ICS_EPRST     E1000_ICR_EPRST
 
 /* Interrupt Mask Set */
 #define E1000_IMS_TXDW      E1000_ICR_TXDW      /* Transmit desc written back */
@@ -1718,6 +1841,9 @@
 #define E1000_IMS_PB_PAR        E1000_ICR_PB_PAR        /* packet buffer parity error */
 #define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
 #define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMS_DSW       E1000_ICR_DSW
+#define E1000_IMS_PHYINT    E1000_ICR_PHYINT
+#define E1000_IMS_EPRST     E1000_ICR_EPRST
 
 /* Interrupt Mask Clear */
 #define E1000_IMC_TXDW      E1000_ICR_TXDW      /* Transmit desc written back */
@@ -1744,6 +1870,9 @@
 #define E1000_IMC_PB_PAR        E1000_ICR_PB_PAR        /* packet buffer parity error */
 #define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
 #define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMC_DSW       E1000_ICR_DSW
+#define E1000_IMC_PHYINT    E1000_ICR_PHYINT
+#define E1000_IMC_EPRST     E1000_ICR_EPRST
 
 /* Receive Control */
 #define E1000_RCTL_RST            0x00000001    /* Software reset */
@@ -1918,9 +2047,10 @@
 #define E1000_MRQC_RSS_FIELD_MASK           0xFFFF0000
 #define E1000_MRQC_RSS_FIELD_IPV4_TCP       0x00010000
 #define E1000_MRQC_RSS_FIELD_IPV4           0x00020000
-#define E1000_MRQC_RSS_FIELD_IPV6_TCP       0x00040000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX    0x00040000
 #define E1000_MRQC_RSS_FIELD_IPV6_EX        0x00080000
 #define E1000_MRQC_RSS_FIELD_IPV6           0x00100000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP       0x00200000
 
 /* Definitions for power management and wakeup registers */
 /* Wake Up Control */
@@ -2010,6 +2140,15 @@
 #define E1000_FWSM_MODE_SHIFT            1
 #define E1000_FWSM_FW_VALID     0x00008000 /* FW established a valid mode */
 
+#define E1000_FWSM_RSPCIPHY        0x00000040 /* Reset PHY on PCI reset */
+#define E1000_FWSM_DISSW           0x10000000 /* FW disable SW Write Access */
+#define E1000_FWSM_SKUSEL_MASK     0x60000000 /* LAN SKU select */
+#define E1000_FWSM_SKUEL_SHIFT     29
+#define E1000_FWSM_SKUSEL_EMB      0x0 /* Embedded SKU */
+#define E1000_FWSM_SKUSEL_CONS     0x1 /* Consumer SKU */
+#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
+#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
+
 /* FFLT Debug Register */
 #define E1000_FFLT_DBG_INVC     0x00100000 /* Invalid /C/ code handling */
 
@@ -2082,6 +2221,8 @@
                              E1000_GCR_TXDSCW_NO_SNOOP      | \
                              E1000_GCR_TXDSCR_NO_SNOOP)
 
+#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL
+
 #define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
 /* Function Active and Power State to MNG */
 #define E1000_FACTPS_FUNC0_POWER_STATE_MASK         0x00000003
@@ -2140,8 +2281,10 @@
 #define EEPROM_PHY_CLASS_WORD         0x0007
 #define EEPROM_INIT_CONTROL1_REG      0x000A
 #define EEPROM_INIT_CONTROL2_REG      0x000F
+#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010
 #define EEPROM_INIT_CONTROL3_PORT_B   0x0014
 #define EEPROM_INIT_3GIO_3            0x001A
+#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020
 #define EEPROM_INIT_CONTROL3_PORT_A   0x0024
 #define EEPROM_CFG                    0x0012
 #define EEPROM_FLASH_VERSION          0x0032
@@ -2153,10 +2296,16 @@
 /* Word definitions for ID LED Settings */
 #define ID_LED_RESERVED_0000 0x0000
 #define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_RESERVED_82573  0xF746
+#define ID_LED_DEFAULT_82573   0x1811
 #define ID_LED_DEFAULT       ((ID_LED_OFF1_ON2 << 12) | \
                               (ID_LED_OFF1_OFF2 << 8) | \
                               (ID_LED_DEF1_DEF2 << 4) | \
                               (ID_LED_DEF1_DEF2))
+#define ID_LED_DEFAULT_ICH8LAN  ((ID_LED_DEF1_DEF2 << 12) | \
+                                 (ID_LED_DEF1_OFF2 <<  8) | \
+                                 (ID_LED_DEF1_ON2  <<  4) | \
+                                 (ID_LED_DEF1_DEF2))
 #define ID_LED_DEF1_DEF2     0x1
 #define ID_LED_DEF1_ON2      0x2
 #define ID_LED_DEF1_OFF2     0x3
@@ -2191,6 +2340,11 @@
 #define EEPROM_WORD0F_ASM_DIR    0x2000
 #define EEPROM_WORD0F_ANE        0x0800
 #define EEPROM_WORD0F_SWPDIO_EXT 0x00F0
+#define EEPROM_WORD0F_LPLU       0x0001
+
+/* Mask bits for fields in Word 0x10/0x20 of the EEPROM */
+#define EEPROM_WORD1020_GIGA_DISABLE         0x0010
+#define EEPROM_WORD1020_GIGA_DISABLE_NON_D0A 0x0008
 
 /* Mask bits for fields in Word 0x1a of the EEPROM */
 #define EEPROM_WORD1A_ASPM_MASK  0x000C
@@ -2265,23 +2419,29 @@
 #define E1000_EXTCNF_CTRL_D_UD_OWNER        0x00000010
 #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
 #define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040
-#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER   0x1FFF0000
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER   0x0FFF0000
 
 #define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH    0x000000FF
 #define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH   0x0000FF00
 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH   0x00FF0000
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE  0x00000001
+#define E1000_EXTCNF_CTRL_SWFLAG            0x00000020
 
 /* PBA constants */
+#define E1000_PBA_8K 0x0008    /* 8KB, default Rx allocation */
 #define E1000_PBA_12K 0x000C    /* 12KB, default Rx allocation */
 #define E1000_PBA_16K 0x0010    /* 16KB, default TX allocation */
 #define E1000_PBA_22K 0x0016
 #define E1000_PBA_24K 0x0018
 #define E1000_PBA_30K 0x001E
 #define E1000_PBA_32K 0x0020
+#define E1000_PBA_34K 0x0022
 #define E1000_PBA_38K 0x0026
 #define E1000_PBA_40K 0x0028
 #define E1000_PBA_48K 0x0030    /* 48KB, default RX allocation */
 
+#define E1000_PBS_16K E1000_PBA_16K
+
 /* Flow Control Constants */
 #define FLOW_CONTROL_ADDRESS_LOW  0x00C28001
 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
@@ -2336,7 +2496,7 @@
 /* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */
 #define AUTO_READ_DONE_TIMEOUT      10
 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
-#define PHY_CFG_TIMEOUT             40
+#define PHY_CFG_TIMEOUT             100
 
 #define E1000_TX_BUFFER_SIZE ((uint32_t)1514)
 
@@ -2764,6 +2924,17 @@
 #define M88E1000_EPSCR_TX_CLK_25      0x0070 /* 25  MHz TX_CLK */
 #define M88E1000_EPSCR_TX_CLK_0       0x0000 /* NO  TX_CLK */
 
+/* M88EC018 Rev 2 specific DownShift settings */
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK  0x0E00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X    0x0000
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X    0x0200
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X    0x0400
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X    0x0600
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X    0x0800
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X    0x0A00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X    0x0C00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X    0x0E00
+
 /* IGP01E1000 Specific Port Config Register - R/W */
 #define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT  0x0010
 #define IGP01E1000_PSCFR_PRE_EN                0x0020
@@ -2990,6 +3161,221 @@
 #define L1LXT971A_PHY_ID   0x001378E0
 #define GG82563_E_PHY_ID   0x01410CA0
 
+
+/* Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define PHY_PAGE_SHIFT        5
+#define PHY_REG(page, reg)    \
+        (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+
+#define IGP3_PHY_PORT_CTRL           \
+        PHY_REG(769, 17) /* Port General Configuration */
+#define IGP3_PHY_RATE_ADAPT_CTRL \
+        PHY_REG(769, 25) /* Rate Adapter Control Register */
+
+#define IGP3_KMRN_FIFO_CTRL_STATS \
+        PHY_REG(770, 16) /* KMRN FIFO's control/status register */
+#define IGP3_KMRN_POWER_MNG_CTRL \
+        PHY_REG(770, 17) /* KMRN Power Management Control Register */
+#define IGP3_KMRN_INBAND_CTRL \
+        PHY_REG(770, 18) /* KMRN Inband Control Register */
+#define IGP3_KMRN_DIAG \
+        PHY_REG(770, 19) /* KMRN Diagnostic register */
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
+#define IGP3_KMRN_ACK_TIMEOUT \
+        PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
+
+#define IGP3_VR_CTRL \
+        PHY_REG(776, 18) /* Voltage regulator control register */
+#define IGP3_VR_CTRL_MODE_SHUT       0x0200 /* Enter powerdown, shutdown VRs */
+
+#define IGP3_CAPABILITY \
+        PHY_REG(776, 19) /* IGP3 Capability Register */
+
+/* Capabilities for SKU Control  */
+#define IGP3_CAP_INITIATE_TEAM       0x0001 /* Able to initiate a team */
+#define IGP3_CAP_WFM                 0x0002 /* Support WoL and PXE */
+#define IGP3_CAP_ASF                 0x0004 /* Support ASF */
+#define IGP3_CAP_LPLU                0x0008 /* Support Low Power Link Up */
+#define IGP3_CAP_DC_AUTO_SPEED       0x0010 /* Support AC/DC Auto Link Speed */
+#define IGP3_CAP_SPD                 0x0020 /* Support Smart Power Down */
+#define IGP3_CAP_MULT_QUEUE          0x0040 /* Support 2 tx & 2 rx queues */
+#define IGP3_CAP_RSS                 0x0080 /* Support RSS */
+#define IGP3_CAP_8021PQ              0x0100 /* Support 802.1Q & 802.1p */
+#define IGP3_CAP_AMT_CB              0x0200 /* Support active manageability and circuit breaker */
+
+#define IGP3_PPC_JORDAN_EN           0x0001
+#define IGP3_PPC_JORDAN_GIGA_SPEED   0x0002
+
+#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS         0x0001
+#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK   0x001E
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA        0x0020
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_100         0x0040
+
+#define IGP3E1000_PHY_MISC_CTRL                0x1B   /* Misc. Ctrl register */
+#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET        0x1000 /* Duplex Manual Set */
+
+#define IGP3_KMRN_EXT_CTRL  PHY_REG(770, 18)
+#define IGP3_KMRN_EC_DIS_INBAND    0x0080
+
+#define IGP03E1000_E_PHY_ID  0x02A80390
+#define IFE_E_PHY_ID         0x02A80330 /* 10/100 PHY */
+#define IFE_PLUS_E_PHY_ID    0x02A80320
+#define IFE_C_E_PHY_ID       0x02A80310
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL   0x10  /* 100BaseTx Extended Status, Control and Address */
+#define IFE_PHY_SPECIAL_CONTROL           0x11  /* 100BaseTx PHY special control register */
+#define IFE_PHY_RCV_FALSE_CARRIER         0x13  /* 100BaseTx Receive False Carrier Counter */
+#define IFE_PHY_RCV_DISCONNECT            0x14  /* 100BaseTx Receive Disconnet Counter */
+#define IFE_PHY_RCV_ERROT_FRAME           0x15  /* 100BaseTx Receive Error Frame Counter */
+#define IFE_PHY_RCV_SYMBOL_ERR            0x16  /* Receive Symbol Error Counter */
+#define IFE_PHY_PREM_EOF_ERR              0x17  /* 100BaseTx Receive Premature End Of Frame Error Counter */
+#define IFE_PHY_RCV_EOF_ERR               0x18  /* 10BaseT Receive End Of Frame Error Counter */
+#define IFE_PHY_TX_JABBER_DETECT          0x19  /* 10BaseT Transmit Jabber Detect Counter */
+#define IFE_PHY_EQUALIZER                 0x1A  /* PHY Equalizer Control and Status */
+#define IFE_PHY_SPECIAL_CONTROL_LED       0x1B  /* PHY special control and LED configuration */
+#define IFE_PHY_MDIX_CONTROL              0x1C  /* MDI/MDI-X Control register */
+#define IFE_PHY_HWI_CONTROL               0x1D  /* Hardware Integrity Control (HWI) */
+
+#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE  0x2000  /* Defaut 1 = Disable auto reduced power down */
+#define IFE_PESC_100BTX_POWER_DOWN           0x0400  /* Indicates the power state of 100BASE-TX */
+#define IFE_PESC_10BTX_POWER_DOWN            0x0200  /* Indicates the power state of 10BASE-T */
+#define IFE_PESC_POLARITY_REVERSED           0x0100  /* Indicates 10BASE-T polarity */
+#define IFE_PESC_PHY_ADDR_MASK               0x007C  /* Bit 6:2 for sampled PHY address */
+#define IFE_PESC_SPEED                       0x0002  /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
+#define IFE_PESC_DUPLEX                      0x0001  /* Auto-negotiation duplex result 1=Full, 0=Half */
+#define IFE_PESC_POLARITY_REVERSED_SHIFT     8
+
+#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN   0x0100  /* 1 = Dyanmic Power Down disabled */
+#define IFE_PSC_FORCE_POLARITY               0x0020  /* 1=Reversed Polarity, 0=Normal */
+#define IFE_PSC_AUTO_POLARITY_DISABLE        0x0010  /* 1=Auto Polarity Disabled, 0=Enabled */
+#define IFE_PSC_JABBER_FUNC_DISABLE          0x0001  /* 1=Jabber Disabled, 0=Normal Jabber Operation */
+#define IFE_PSC_FORCE_POLARITY_SHIFT         5
+#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT  4
+
+#define IFE_PMC_AUTO_MDIX                    0x0080  /* 1=enable MDI/MDI-X feature, default 0=disabled */
+#define IFE_PMC_FORCE_MDIX                   0x0040  /* 1=force MDIX-X, 0=force MDI */
+#define IFE_PMC_MDIX_STATUS                  0x0020  /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_AUTO_MDIX_COMPLETE           0x0010  /* Resolution algorthm is completed */
+#define IFE_PMC_MDIX_MODE_SHIFT              6
+#define IFE_PHC_MDIX_RESET_ALL_MASK          0x0000  /* Disable auto MDI-X */
+
+#define IFE_PHC_HWI_ENABLE                   0x8000  /* Enable the HWI feature */
+#define IFE_PHC_ABILITY_CHECK                0x4000  /* 1= Test Passed, 0=failed */
+#define IFE_PHC_TEST_EXEC                    0x2000  /* PHY launch test pulses on the wire */
+#define IFE_PHC_HIGHZ                        0x0200  /* 1 = Open Circuit */
+#define IFE_PHC_LOWZ                         0x0400  /* 1 = Short Circuit */
+#define IFE_PHC_LOW_HIGH_Z_MASK              0x0600  /* Mask for indication type of problem on the line */
+#define IFE_PHC_DISTANCE_MASK                0x01FF  /* Mask for distance to the cable problem, in 80cm granularity */
+#define IFE_PHC_RESET_ALL_MASK               0x0000  /* Disable HWI */
+#define IFE_PSCL_PROBE_MODE                  0x0020  /* LED Probe mode */
+#define IFE_PSCL_PROBE_LEDS_OFF              0x0006  /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON               0x0007  /* Force LEDs 0 and 2 on */
+
+#define ICH8_FLASH_COMMAND_TIMEOUT           500   /* 500 ms , should be adjusted */
+#define ICH8_FLASH_CYCLE_REPEAT_COUNT        10    /* 10 cycles , should be adjusted */
+#define ICH8_FLASH_SEG_SIZE_256              256
+#define ICH8_FLASH_SEG_SIZE_4K               4096
+#define ICH8_FLASH_SEG_SIZE_64K              65536
+
+#define ICH8_CYCLE_READ                      0x0
+#define ICH8_CYCLE_RESERVED                  0x1
+#define ICH8_CYCLE_WRITE                     0x2
+#define ICH8_CYCLE_ERASE                     0x3
+
+#define ICH8_FLASH_GFPREG   0x0000
+#define ICH8_FLASH_HSFSTS   0x0004
+#define ICH8_FLASH_HSFCTL   0x0006
+#define ICH8_FLASH_FADDR    0x0008
+#define ICH8_FLASH_FDATA0   0x0010
+#define ICH8_FLASH_FRACC    0x0050
+#define ICH8_FLASH_FREG0    0x0054
+#define ICH8_FLASH_FREG1    0x0058
+#define ICH8_FLASH_FREG2    0x005C
+#define ICH8_FLASH_FREG3    0x0060
+#define ICH8_FLASH_FPR0     0x0074
+#define ICH8_FLASH_FPR1     0x0078
+#define ICH8_FLASH_SSFSTS   0x0090
+#define ICH8_FLASH_SSFCTL   0x0092
+#define ICH8_FLASH_PREOP    0x0094
+#define ICH8_FLASH_OPTYPE   0x0096
+#define ICH8_FLASH_OPMENU   0x0098
+
+#define ICH8_FLASH_REG_MAPSIZE      0x00A0
+#define ICH8_FLASH_SECTOR_SIZE      4096
+#define ICH8_GFPREG_BASE_MASK       0x1FFF
+#define ICH8_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
+
+/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
+/* Offset 04h HSFSTS */
+union ich8_hws_flash_status {
+    struct ich8_hsfsts {
+#ifdef E1000_BIG_ENDIAN
+        uint16_t reserved2      :6;
+        uint16_t fldesvalid     :1;
+        uint16_t flockdn        :1;
+        uint16_t flcdone        :1;
+        uint16_t flcerr         :1;
+        uint16_t dael           :1;
+        uint16_t berasesz       :2;
+        uint16_t flcinprog      :1;
+        uint16_t reserved1      :2;
+#else
+        uint16_t flcdone        :1;   /* bit 0 Flash Cycle Done */
+        uint16_t flcerr         :1;   /* bit 1 Flash Cycle Error */
+        uint16_t dael           :1;   /* bit 2 Direct Access error Log */
+        uint16_t berasesz       :2;   /* bit 4:3 Block/Sector Erase Size */
+        uint16_t flcinprog      :1;   /* bit 5 flash SPI cycle in Progress */
+        uint16_t reserved1      :2;   /* bit 13:6 Reserved */
+        uint16_t reserved2      :6;   /* bit 13:6 Reserved */
+        uint16_t fldesvalid     :1;   /* bit 14 Flash Descriptor Valid */
+        uint16_t flockdn        :1;   /* bit 15 Flash Configuration Lock-Down */
+#endif
+    } hsf_status;
+    uint16_t regval;
+};
+
+/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */
+/* Offset 06h FLCTL */
+union ich8_hws_flash_ctrl {
+    struct ich8_hsflctl {
+#ifdef E1000_BIG_ENDIAN
+        uint16_t fldbcount      :2;
+        uint16_t flockdn        :6;
+        uint16_t flcgo          :1;
+        uint16_t flcycle        :2;
+        uint16_t reserved       :5;
+#else
+        uint16_t flcgo          :1;   /* 0 Flash Cycle Go */
+        uint16_t flcycle        :2;   /* 2:1 Flash Cycle */
+        uint16_t reserved       :5;   /* 7:3 Reserved  */
+        uint16_t fldbcount      :2;   /* 9:8 Flash Data Byte Count */
+        uint16_t flockdn        :6;   /* 15:10 Reserved */
+#endif
+    } hsf_ctrl;
+    uint16_t regval;
+};
+
+/* ICH8 Flash Region Access Permissions */
+union ich8_hws_flash_regacc {
+    struct ich8_flracc {
+#ifdef E1000_BIG_ENDIAN
+        uint32_t gmwag          :8;
+        uint32_t gmrag          :8;
+        uint32_t grwa           :8;
+        uint32_t grra           :8;
+#else
+        uint32_t grra           :8;   /* 0:7 GbE region Read Access */
+        uint32_t grwa           :8;   /* 8:15 GbE region Write Access */
+        uint32_t gmrag          :8;   /* 23:16 GbE Master Read Access Grant  */
+        uint32_t gmwag          :8;   /* 31:24 GbE Master Write Access Grant */
+#endif
+    } hsf_flregacc;
+    uint16_t regval;
+};
+
 /* Miscellaneous PHY bit definitions. */
 #define PHY_PREAMBLE        0xFFFFFFFF
 #define PHY_SOF             0x01
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index f77624f..6e7d31b 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -36,7 +36,7 @@
 #else
 #define DRIVERNAPI "-NAPI"
 #endif
-#define DRV_VERSION "7.0.38-k4"DRIVERNAPI
+#define DRV_VERSION "7.1.9-k2"DRIVERNAPI
 char e1000_driver_version[] = DRV_VERSION;
 static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
 
@@ -73,6 +73,11 @@
 	INTEL_E1000_ETHERNET_DEVICE(0x1026),
 	INTEL_E1000_ETHERNET_DEVICE(0x1027),
 	INTEL_E1000_ETHERNET_DEVICE(0x1028),
+	INTEL_E1000_ETHERNET_DEVICE(0x1049),
+	INTEL_E1000_ETHERNET_DEVICE(0x104A),
+	INTEL_E1000_ETHERNET_DEVICE(0x104B),
+	INTEL_E1000_ETHERNET_DEVICE(0x104C),
+	INTEL_E1000_ETHERNET_DEVICE(0x104D),
 	INTEL_E1000_ETHERNET_DEVICE(0x105E),
 	INTEL_E1000_ETHERNET_DEVICE(0x105F),
 	INTEL_E1000_ETHERNET_DEVICE(0x1060),
@@ -96,6 +101,8 @@
 	INTEL_E1000_ETHERNET_DEVICE(0x109A),
 	INTEL_E1000_ETHERNET_DEVICE(0x10B5),
 	INTEL_E1000_ETHERNET_DEVICE(0x10B9),
+	INTEL_E1000_ETHERNET_DEVICE(0x10BA),
+	INTEL_E1000_ETHERNET_DEVICE(0x10BB),
 	/* required last entry */
 	{0,}
 };
@@ -133,7 +140,6 @@
 static void e1000_set_multi(struct net_device *netdev);
 static void e1000_update_phy_info(unsigned long data);
 static void e1000_watchdog(unsigned long data);
-static void e1000_watchdog_task(struct e1000_adapter *adapter);
 static void e1000_82547_tx_fifo_stall(unsigned long data);
 static int e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
 static struct net_device_stats * e1000_get_stats(struct net_device *netdev);
@@ -178,8 +184,8 @@
 static void e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
 static void e1000_restore_vlan(struct e1000_adapter *adapter);
 
-#ifdef CONFIG_PM
 static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
+#ifdef CONFIG_PM
 static int e1000_resume(struct pci_dev *pdev);
 #endif
 static void e1000_shutdown(struct pci_dev *pdev);
@@ -206,8 +212,8 @@
 	.probe    = e1000_probe,
 	.remove   = __devexit_p(e1000_remove),
 	/* Power Managment Hooks */
-#ifdef CONFIG_PM
 	.suspend  = e1000_suspend,
+#ifdef CONFIG_PM
 	.resume   = e1000_resume,
 #endif
 	.shutdown = e1000_shutdown,
@@ -261,6 +267,44 @@
 
 module_exit(e1000_exit_module);
 
+static int e1000_request_irq(struct e1000_adapter *adapter)
+{
+	struct net_device *netdev = adapter->netdev;
+	int flags, err = 0;
+
+	flags = IRQF_SHARED;
+#ifdef CONFIG_PCI_MSI
+	if (adapter->hw.mac_type > e1000_82547_rev_2) {
+		adapter->have_msi = TRUE;
+		if ((err = pci_enable_msi(adapter->pdev))) {
+			DPRINTK(PROBE, ERR,
+			 "Unable to allocate MSI interrupt Error: %d\n", err);
+			adapter->have_msi = FALSE;
+		}
+	}
+	if (adapter->have_msi)
+		flags &= ~SA_SHIRQ;
+#endif
+	if ((err = request_irq(adapter->pdev->irq, &e1000_intr, flags,
+	                       netdev->name, netdev)))
+		DPRINTK(PROBE, ERR,
+		        "Unable to allocate interrupt Error: %d\n", err);
+
+	return err;
+}
+
+static void e1000_free_irq(struct e1000_adapter *adapter)
+{
+	struct net_device *netdev = adapter->netdev;
+
+	free_irq(adapter->pdev->irq, netdev);
+
+#ifdef CONFIG_PCI_MSI
+	if (adapter->have_msi)
+		pci_disable_msi(adapter->pdev);
+#endif
+}
+
 /**
  * e1000_irq_disable - Mask off interrupt generation on the NIC
  * @adapter: board private structure
@@ -329,6 +373,7 @@
 {
 	uint32_t ctrl_ext;
 	uint32_t swsm;
+	uint32_t extcnf;
 
 	/* Let firmware taken over control of h/w */
 	switch (adapter->hw.mac_type) {
@@ -343,6 +388,11 @@
 		swsm = E1000_READ_REG(&adapter->hw, SWSM);
 		E1000_WRITE_REG(&adapter->hw, SWSM,
 				swsm & ~E1000_SWSM_DRV_LOAD);
+	case e1000_ich8lan:
+		extcnf = E1000_READ_REG(&adapter->hw, CTRL_EXT);
+		E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
+				extcnf & ~E1000_CTRL_EXT_DRV_LOAD);
+		break;
 	default:
 		break;
 	}
@@ -364,6 +414,7 @@
 {
 	uint32_t ctrl_ext;
 	uint32_t swsm;
+	uint32_t extcnf;
 	/* Let firmware know the driver has taken over */
 	switch (adapter->hw.mac_type) {
 	case e1000_82571:
@@ -378,6 +429,11 @@
 		E1000_WRITE_REG(&adapter->hw, SWSM,
 				swsm | E1000_SWSM_DRV_LOAD);
 		break;
+	case e1000_ich8lan:
+		extcnf = E1000_READ_REG(&adapter->hw, EXTCNF_CTRL);
+		E1000_WRITE_REG(&adapter->hw, EXTCNF_CTRL,
+				extcnf | E1000_EXTCNF_CTRL_SWFLAG);
+		break;
 	default:
 		break;
 	}
@@ -387,18 +443,10 @@
 e1000_up(struct e1000_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
-	int i, err;
+	int i;
 
 	/* hardware has been reset, we need to reload some things */
 
-	/* Reset the PHY if it was previously powered down */
-	if (adapter->hw.media_type == e1000_media_type_copper) {
-		uint16_t mii_reg;
-		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
-		if (mii_reg & MII_CR_POWER_DOWN)
-			e1000_phy_hw_reset(&adapter->hw);
-	}
-
 	e1000_set_multi(netdev);
 
 	e1000_restore_vlan(adapter);
@@ -415,24 +463,6 @@
 		                      E1000_DESC_UNUSED(ring));
 	}
 
-#ifdef CONFIG_PCI_MSI
-	if (adapter->hw.mac_type > e1000_82547_rev_2) {
-		adapter->have_msi = TRUE;
-		if ((err = pci_enable_msi(adapter->pdev))) {
-			DPRINTK(PROBE, ERR,
-			 "Unable to allocate MSI interrupt Error: %d\n", err);
-			adapter->have_msi = FALSE;
-		}
-	}
-#endif
-	if ((err = request_irq(adapter->pdev->irq, &e1000_intr,
-		              IRQF_SHARED | IRQF_SAMPLE_RANDOM,
-		              netdev->name, netdev))) {
-		DPRINTK(PROBE, ERR,
-		    "Unable to allocate interrupt Error: %d\n", err);
-		return err;
-	}
-
 	adapter->tx_queue_len = netdev->tx_queue_len;
 
 	mod_timer(&adapter->watchdog_timer, jiffies);
@@ -445,21 +475,60 @@
 	return 0;
 }
 
+/**
+ * e1000_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000_reset ***
+ *
+ **/
+
+static void e1000_power_up_phy(struct e1000_adapter *adapter)
+{
+	uint16_t mii_reg = 0;
+
+	/* Just clear the power down bit to wake the phy back up */
+	if (adapter->hw.media_type == e1000_media_type_copper) {
+		/* according to the manual, the phy will retain its
+		 * settings across a power-down/up cycle */
+		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
+		mii_reg &= ~MII_CR_POWER_DOWN;
+		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
+	}
+}
+
+static void e1000_power_down_phy(struct e1000_adapter *adapter)
+{
+	boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
+	                              e1000_check_mng_mode(&adapter->hw);
+	/* Power down the PHY so no link is implied when interface is down
+	 * The PHY cannot be powered down if any of the following is TRUE
+	 * (a) WoL is enabled
+	 * (b) AMT is active
+	 * (c) SoL/IDER session is active */
+	if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
+	    adapter->hw.mac_type != e1000_ich8lan &&
+	    adapter->hw.media_type == e1000_media_type_copper &&
+	    !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
+	    !mng_mode_enabled &&
+	    !e1000_check_phy_reset_block(&adapter->hw)) {
+		uint16_t mii_reg = 0;
+		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
+		mii_reg |= MII_CR_POWER_DOWN;
+		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
+		mdelay(1);
+	}
+}
+
 void
 e1000_down(struct e1000_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
-	boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
-				     e1000_check_mng_mode(&adapter->hw);
 
 	e1000_irq_disable(adapter);
 
-	free_irq(adapter->pdev->irq, netdev);
-#ifdef CONFIG_PCI_MSI
-	if (adapter->hw.mac_type > e1000_82547_rev_2 &&
-	   adapter->have_msi == TRUE)
-		pci_disable_msi(adapter->pdev);
-#endif
 	del_timer_sync(&adapter->tx_fifo_stall_timer);
 	del_timer_sync(&adapter->watchdog_timer);
 	del_timer_sync(&adapter->phy_info_timer);
@@ -476,23 +545,17 @@
 	e1000_reset(adapter);
 	e1000_clean_all_tx_rings(adapter);
 	e1000_clean_all_rx_rings(adapter);
+}
 
-	/* Power down the PHY so no link is implied when interface is down *
-	 * The PHY cannot be powered down if any of the following is TRUE *
-	 * (a) WoL is enabled
-	 * (b) AMT is active
-	 * (c) SoL/IDER session is active */
-	if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
-	   adapter->hw.media_type == e1000_media_type_copper &&
-	   !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
-	   !mng_mode_enabled &&
-	   !e1000_check_phy_reset_block(&adapter->hw)) {
-		uint16_t mii_reg;
-		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
-		mii_reg |= MII_CR_POWER_DOWN;
-		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
-		mdelay(1);
-	}
+void
+e1000_reinit_locked(struct e1000_adapter *adapter)
+{
+	WARN_ON(in_interrupt());
+	while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+		msleep(1);
+	e1000_down(adapter);
+	e1000_up(adapter);
+	clear_bit(__E1000_RESETTING, &adapter->flags);
 }
 
 void
@@ -518,6 +581,9 @@
 	case e1000_82573:
 		pba = E1000_PBA_12K;
 		break;
+	case e1000_ich8lan:
+		pba = E1000_PBA_8K;
+		break;
 	default:
 		pba = E1000_PBA_48K;
 		break;
@@ -542,6 +608,12 @@
 	/* Set the FC high water mark to 90% of the FIFO size.
 	 * Required to clear last 3 LSB */
 	fc_high_water_mark = ((pba * 9216)/10) & 0xFFF8;
+	/* We can't use 90% on small FIFOs because the remainder
+	 * would be less than 1 full frame.  In this case, we size
+	 * it to allow at least a full frame above the high water
+	 *  mark. */
+	if (pba < E1000_PBA_16K)
+		fc_high_water_mark = (pba * 1024) - 1600;
 
 	adapter->hw.fc_high_water = fc_high_water_mark;
 	adapter->hw.fc_low_water = fc_high_water_mark - 8;
@@ -564,6 +636,23 @@
 
 	e1000_reset_adaptive(&adapter->hw);
 	e1000_phy_get_info(&adapter->hw, &adapter->phy_info);
+
+	if (!adapter->smart_power_down &&
+	    (adapter->hw.mac_type == e1000_82571 ||
+	     adapter->hw.mac_type == e1000_82572)) {
+		uint16_t phy_data = 0;
+		/* speed up time to link by disabling smart power down, ignore
+		 * the return value of this function because there is nothing
+		 * different we would do if it failed */
+		e1000_read_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT,
+		                   &phy_data);
+		phy_data &= ~IGP02E1000_PM_SPD;
+		e1000_write_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT,
+		                    phy_data);
+	}
+
+	if (adapter->hw.mac_type < e1000_ich8lan)
+	/* FIXME: this code is duplicate and wrong for PCI Express */
 	if (adapter->en_mng_pt) {
 		manc = E1000_READ_REG(&adapter->hw, MANC);
 		manc |= (E1000_MANC_ARP_EN | E1000_MANC_EN_MNG2HOST);
@@ -590,6 +679,7 @@
 	struct net_device *netdev;
 	struct e1000_adapter *adapter;
 	unsigned long mmio_start, mmio_len;
+	unsigned long flash_start, flash_len;
 
 	static int cards_found = 0;
 	static int e1000_ksp3_port_a = 0; /* global ksp3 port a indication */
@@ -599,10 +689,12 @@
 	if ((err = pci_enable_device(pdev)))
 		return err;
 
-	if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK))) {
+	if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) &&
+	    !(err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK))) {
 		pci_using_dac = 1;
 	} else {
-		if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) {
+		if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) &&
+		    (err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) {
 			E1000_ERR("No usable DMA configuration, aborting\n");
 			return err;
 		}
@@ -682,6 +774,19 @@
 	if ((err = e1000_sw_init(adapter)))
 		goto err_sw_init;
 
+	/* Flash BAR mapping must happen after e1000_sw_init
+	 * because it depends on mac_type */
+	if ((adapter->hw.mac_type == e1000_ich8lan) &&
+	   (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
+		flash_start = pci_resource_start(pdev, 1);
+		flash_len = pci_resource_len(pdev, 1);
+		adapter->hw.flash_address = ioremap(flash_start, flash_len);
+		if (!adapter->hw.flash_address) {
+			err = -EIO;
+			goto err_flashmap;
+		}
+	}
+
 	if ((err = e1000_check_phy_reset_block(&adapter->hw)))
 		DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
 
@@ -700,6 +805,8 @@
 				   NETIF_F_HW_VLAN_TX |
 				   NETIF_F_HW_VLAN_RX |
 				   NETIF_F_HW_VLAN_FILTER;
+		if (adapter->hw.mac_type == e1000_ich8lan)
+			netdev->features &= ~NETIF_F_HW_VLAN_FILTER;
 	}
 
 #ifdef NETIF_F_TSO
@@ -715,11 +822,17 @@
 	if (pci_using_dac)
 		netdev->features |= NETIF_F_HIGHDMA;
 
-	/* hard_start_xmit is safe against parallel locking */
 	netdev->features |= NETIF_F_LLTX;
 
 	adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw);
 
+	/* initialize eeprom parameters */
+
+	if (e1000_init_eeprom_params(&adapter->hw)) {
+		E1000_ERR("EEPROM initialization failed\n");
+		return -EIO;
+	}
+
 	/* before reading the EEPROM, reset the controller to
 	 * put the device in a known good starting state */
 
@@ -758,9 +871,6 @@
 	adapter->watchdog_timer.function = &e1000_watchdog;
 	adapter->watchdog_timer.data = (unsigned long) adapter;
 
-	INIT_WORK(&adapter->watchdog_task,
-		(void (*)(void *))e1000_watchdog_task, adapter);
-
 	init_timer(&adapter->phy_info_timer);
 	adapter->phy_info_timer.function = &e1000_update_phy_info;
 	adapter->phy_info_timer.data = (unsigned long) adapter;
@@ -790,6 +900,11 @@
 			EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
 		eeprom_apme_mask = E1000_EEPROM_82544_APM;
 		break;
+	case e1000_ich8lan:
+		e1000_read_eeprom(&adapter->hw,
+			EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data);
+		eeprom_apme_mask = E1000_EEPROM_ICH8_APME;
+		break;
 	case e1000_82546:
 	case e1000_82546_rev_3:
 	case e1000_82571:
@@ -849,6 +964,9 @@
 	return 0;
 
 err_register:
+	if (adapter->hw.flash_address)
+		iounmap(adapter->hw.flash_address);
+err_flashmap:
 err_sw_init:
 err_eeprom:
 	iounmap(adapter->hw.hw_addr);
@@ -882,6 +1000,7 @@
 	flush_scheduled_work();
 
 	if (adapter->hw.mac_type >= e1000_82540 &&
+	   adapter->hw.mac_type != e1000_ich8lan &&
 	   adapter->hw.media_type == e1000_media_type_copper) {
 		manc = E1000_READ_REG(&adapter->hw, MANC);
 		if (manc & E1000_MANC_SMBUS_EN) {
@@ -910,6 +1029,8 @@
 #endif
 
 	iounmap(adapter->hw.hw_addr);
+	if (adapter->hw.flash_address)
+		iounmap(adapter->hw.flash_address);
 	pci_release_regions(pdev);
 
 	free_netdev(netdev);
@@ -960,13 +1081,6 @@
 		return -EIO;
 	}
 
-	/* initialize eeprom parameters */
-
-	if (e1000_init_eeprom_params(hw)) {
-		E1000_ERR("EEPROM initialization failed\n");
-		return -EIO;
-	}
-
 	switch (hw->mac_type) {
 	default:
 		break;
@@ -1078,6 +1192,10 @@
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	int err;
 
+	/* disallow open during test */
+	if (test_bit(__E1000_DRIVER_TESTING, &adapter->flags))
+		return -EBUSY;
+
 	/* allocate transmit descriptors */
 
 	if ((err = e1000_setup_all_tx_resources(adapter)))
@@ -1088,6 +1206,12 @@
 	if ((err = e1000_setup_all_rx_resources(adapter)))
 		goto err_setup_rx;
 
+	err = e1000_request_irq(adapter);
+	if (err)
+		goto err_up;
+
+	e1000_power_up_phy(adapter);
+
 	if ((err = e1000_up(adapter)))
 		goto err_up;
 	adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
@@ -1131,7 +1255,10 @@
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 
+	WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
 	e1000_down(adapter);
+	e1000_power_down_phy(adapter);
+	e1000_free_irq(adapter);
 
 	e1000_free_all_tx_resources(adapter);
 	e1000_free_all_rx_resources(adapter);
@@ -1189,8 +1316,7 @@
 	int size;
 
 	size = sizeof(struct e1000_buffer) * txdr->count;
-
-	txdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus));
+	txdr->buffer_info = vmalloc(size);
 	if (!txdr->buffer_info) {
 		DPRINTK(PROBE, ERR,
 		"Unable to allocate memory for the transmit descriptor ring\n");
@@ -1302,11 +1428,11 @@
 		tdba = adapter->tx_ring[0].dma;
 		tdlen = adapter->tx_ring[0].count *
 			sizeof(struct e1000_tx_desc);
-		E1000_WRITE_REG(hw, TDBAL, (tdba & 0x00000000ffffffffULL));
-		E1000_WRITE_REG(hw, TDBAH, (tdba >> 32));
 		E1000_WRITE_REG(hw, TDLEN, tdlen);
-		E1000_WRITE_REG(hw, TDH, 0);
+		E1000_WRITE_REG(hw, TDBAH, (tdba >> 32));
+		E1000_WRITE_REG(hw, TDBAL, (tdba & 0x00000000ffffffffULL));
 		E1000_WRITE_REG(hw, TDT, 0);
+		E1000_WRITE_REG(hw, TDH, 0);
 		adapter->tx_ring[0].tdh = E1000_TDH;
 		adapter->tx_ring[0].tdt = E1000_TDT;
 		break;
@@ -1418,7 +1544,7 @@
 	int size, desc_len;
 
 	size = sizeof(struct e1000_buffer) * rxdr->count;
-	rxdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus));
+	rxdr->buffer_info = vmalloc(size);
 	if (!rxdr->buffer_info) {
 		DPRINTK(PROBE, ERR,
 		"Unable to allocate memory for the receive descriptor ring\n");
@@ -1560,9 +1686,6 @@
 		E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
 		(adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT);
 
-	if (adapter->hw.mac_type > e1000_82543)
-		rctl |= E1000_RCTL_SECRC;
-
 	if (adapter->hw.tbi_compatibility_on == 1)
 		rctl |= E1000_RCTL_SBP;
 	else
@@ -1628,7 +1751,7 @@
 		rfctl |= E1000_RFCTL_IPV6_DIS;
 		E1000_WRITE_REG(&adapter->hw, RFCTL, rfctl);
 
-		rctl |= E1000_RCTL_DTYP_PS | E1000_RCTL_SECRC;
+		rctl |= E1000_RCTL_DTYP_PS;
 
 		psrctl |= adapter->rx_ps_bsize0 >>
 			E1000_PSRCTL_BSIZE0_SHIFT;
@@ -1712,11 +1835,11 @@
 	case 1:
 	default:
 		rdba = adapter->rx_ring[0].dma;
-		E1000_WRITE_REG(hw, RDBAL, (rdba & 0x00000000ffffffffULL));
-		E1000_WRITE_REG(hw, RDBAH, (rdba >> 32));
 		E1000_WRITE_REG(hw, RDLEN, rdlen);
-		E1000_WRITE_REG(hw, RDH, 0);
+		E1000_WRITE_REG(hw, RDBAH, (rdba >> 32));
+		E1000_WRITE_REG(hw, RDBAL, (rdba & 0x00000000ffffffffULL));
 		E1000_WRITE_REG(hw, RDT, 0);
+		E1000_WRITE_REG(hw, RDH, 0);
 		adapter->rx_ring[0].rdh = E1000_RDH;
 		adapter->rx_ring[0].rdt = E1000_RDT;
 		break;
@@ -1741,9 +1864,6 @@
 		E1000_WRITE_REG(hw, RXCSUM, rxcsum);
 	}
 
-	if (hw->mac_type == e1000_82573)
-		E1000_WRITE_REG(hw, ERT, 0x0100);
-
 	/* Enable Receives */
 	E1000_WRITE_REG(hw, RCTL, rctl);
 }
@@ -2083,6 +2203,12 @@
 	uint32_t rctl;
 	uint32_t hash_value;
 	int i, rar_entries = E1000_RAR_ENTRIES;
+	int mta_reg_count = (hw->mac_type == e1000_ich8lan) ?
+				E1000_NUM_MTA_REGISTERS_ICH8LAN :
+				E1000_NUM_MTA_REGISTERS;
+
+	if (adapter->hw.mac_type == e1000_ich8lan)
+		rar_entries = E1000_RAR_ENTRIES_ICH8LAN;
 
 	/* reserve RAR[14] for LAA over-write work-around */
 	if (adapter->hw.mac_type == e1000_82571)
@@ -2121,14 +2247,18 @@
 			mc_ptr = mc_ptr->next;
 		} else {
 			E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0);
+			E1000_WRITE_FLUSH(hw);
 			E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0);
+			E1000_WRITE_FLUSH(hw);
 		}
 	}
 
 	/* clear the old settings from the multicast hash table */
 
-	for (i = 0; i < E1000_NUM_MTA_REGISTERS; i++)
+	for (i = 0; i < mta_reg_count; i++) {
 		E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+		E1000_WRITE_FLUSH(hw);
+	}
 
 	/* load any remaining addresses into the hash table */
 
@@ -2201,19 +2331,19 @@
 e1000_watchdog(unsigned long data)
 {
 	struct e1000_adapter *adapter = (struct e1000_adapter *) data;
-
-	/* Do the rest outside of interrupt context */
-	schedule_work(&adapter->watchdog_task);
-}
-
-static void
-e1000_watchdog_task(struct e1000_adapter *adapter)
-{
 	struct net_device *netdev = adapter->netdev;
 	struct e1000_tx_ring *txdr = adapter->tx_ring;
 	uint32_t link, tctl;
+	int32_t ret_val;
 
-	e1000_check_for_link(&adapter->hw);
+	ret_val = e1000_check_for_link(&adapter->hw);
+	if ((ret_val == E1000_ERR_PHY) &&
+	    (adapter->hw.phy_type == e1000_phy_igp_3) &&
+	    (E1000_READ_REG(&adapter->hw, CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
+		/* See e1000_kumeran_lock_loss_workaround() */
+		DPRINTK(LINK, INFO,
+			"Gigabit has been disabled, downgrading speed\n");
+	}
 	if (adapter->hw.mac_type == e1000_82573) {
 		e1000_enable_tx_pkt_filtering(&adapter->hw);
 		if (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id)
@@ -2394,7 +2524,7 @@
 	uint8_t ipcss, ipcso, tucss, tucso, hdr_len;
 	int err;
 
-	if (skb_shinfo(skb)->gso_size) {
+	if (skb_is_gso(skb)) {
 		if (skb_header_cloned(skb)) {
 			err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
 			if (err)
@@ -2519,7 +2649,7 @@
 		 * tso gets written back prematurely before the data is fully
 		 * DMA'd to the controller */
 		if (!skb->data_len && tx_ring->last_tx_tso &&
-		    !skb_shinfo(skb)->gso_size) {
+		    !skb_is_gso(skb)) {
 			tx_ring->last_tx_tso = 0;
 			size -= 4;
 		}
@@ -2779,9 +2909,10 @@
 			case e1000_82571:
 			case e1000_82572:
 			case e1000_82573:
+			case e1000_ich8lan:
 				pull_size = min((unsigned int)4, skb->data_len);
 				if (!__pskb_pull_tail(skb, pull_size)) {
-					printk(KERN_ERR
+					DPRINTK(DRV, ERR,
 						"__pskb_pull_tail failed.\n");
 					dev_kfree_skb_any(skb);
 					return NETDEV_TX_OK;
@@ -2806,8 +2937,7 @@
 
 #ifdef NETIF_F_TSO
 	/* Controller Erratum workaround */
-	if (!skb->data_len && tx_ring->last_tx_tso &&
-	    !skb_shinfo(skb)->gso_size)
+	if (!skb->data_len && tx_ring->last_tx_tso && !skb_is_gso(skb))
 		count++;
 #endif
 
@@ -2919,8 +3049,7 @@
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 
-	e1000_down(adapter);
-	e1000_up(adapter);
+	e1000_reinit_locked(adapter);
 }
 
 /**
@@ -2964,6 +3093,7 @@
 	/* Adapter-specific max frame size limits. */
 	switch (adapter->hw.mac_type) {
 	case e1000_undefined ... e1000_82542_rev2_1:
+	case e1000_ich8lan:
 		if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) {
 			DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
 			return -EINVAL;
@@ -3026,10 +3156,8 @@
 
 	netdev->mtu = new_mtu;
 
-	if (netif_running(netdev)) {
-		e1000_down(adapter);
-		e1000_up(adapter);
-	}
+	if (netif_running(netdev))
+		e1000_reinit_locked(adapter);
 
 	adapter->hw.max_frame_size = max_frame;
 
@@ -3074,12 +3202,15 @@
 	adapter->stats.bprc += E1000_READ_REG(hw, BPRC);
 	adapter->stats.mprc += E1000_READ_REG(hw, MPRC);
 	adapter->stats.roc += E1000_READ_REG(hw, ROC);
+
+	if (adapter->hw.mac_type != e1000_ich8lan) {
 	adapter->stats.prc64 += E1000_READ_REG(hw, PRC64);
 	adapter->stats.prc127 += E1000_READ_REG(hw, PRC127);
 	adapter->stats.prc255 += E1000_READ_REG(hw, PRC255);
 	adapter->stats.prc511 += E1000_READ_REG(hw, PRC511);
 	adapter->stats.prc1023 += E1000_READ_REG(hw, PRC1023);
 	adapter->stats.prc1522 += E1000_READ_REG(hw, PRC1522);
+	}
 
 	adapter->stats.symerrs += E1000_READ_REG(hw, SYMERRS);
 	adapter->stats.mpc += E1000_READ_REG(hw, MPC);
@@ -3107,12 +3238,16 @@
 	adapter->stats.totl += E1000_READ_REG(hw, TOTL);
 	adapter->stats.toth += E1000_READ_REG(hw, TOTH);
 	adapter->stats.tpr += E1000_READ_REG(hw, TPR);
+
+	if (adapter->hw.mac_type != e1000_ich8lan) {
 	adapter->stats.ptc64 += E1000_READ_REG(hw, PTC64);
 	adapter->stats.ptc127 += E1000_READ_REG(hw, PTC127);
 	adapter->stats.ptc255 += E1000_READ_REG(hw, PTC255);
 	adapter->stats.ptc511 += E1000_READ_REG(hw, PTC511);
 	adapter->stats.ptc1023 += E1000_READ_REG(hw, PTC1023);
 	adapter->stats.ptc1522 += E1000_READ_REG(hw, PTC1522);
+	}
+
 	adapter->stats.mptc += E1000_READ_REG(hw, MPTC);
 	adapter->stats.bptc += E1000_READ_REG(hw, BPTC);
 
@@ -3134,6 +3269,8 @@
 	if (hw->mac_type > e1000_82547_rev_2) {
 		adapter->stats.iac += E1000_READ_REG(hw, IAC);
 		adapter->stats.icrxoc += E1000_READ_REG(hw, ICRXOC);
+
+		if (adapter->hw.mac_type != e1000_ich8lan) {
 		adapter->stats.icrxptc += E1000_READ_REG(hw, ICRXPTC);
 		adapter->stats.icrxatc += E1000_READ_REG(hw, ICRXATC);
 		adapter->stats.ictxptc += E1000_READ_REG(hw, ICTXPTC);
@@ -3141,6 +3278,7 @@
 		adapter->stats.ictxqec += E1000_READ_REG(hw, ICTXQEC);
 		adapter->stats.ictxqmtc += E1000_READ_REG(hw, ICTXQMTC);
 		adapter->stats.icrxdmtc += E1000_READ_REG(hw, ICRXDMTC);
+		}
 	}
 
 	/* Fill out the OS statistics structure */
@@ -3547,7 +3685,8 @@
 			/* All receives must fit into a single buffer */
 			E1000_DBG("%s: Receive packet consumed multiple"
 				  " buffers\n", netdev->name);
-			dev_kfree_skb_irq(skb);
+			/* recycle */
+			buffer_info-> skb = skb;
 			goto next_desc;
 		}
 
@@ -3675,7 +3814,6 @@
 	buffer_info = &rx_ring->buffer_info[i];
 
 	while (staterr & E1000_RXD_STAT_DD) {
-		buffer_info = &rx_ring->buffer_info[i];
 		ps_page = &rx_ring->ps_page[i];
 		ps_page_dma = &rx_ring->ps_page_dma[i];
 #ifdef CONFIG_E1000_NAPI
@@ -4180,10 +4318,9 @@
 						return retval;
 					}
 				}
-				if (netif_running(adapter->netdev)) {
-					e1000_down(adapter);
-					e1000_up(adapter);
-				} else
+				if (netif_running(adapter->netdev))
+					e1000_reinit_locked(adapter);
+				else
 					e1000_reset(adapter);
 				break;
 			case M88E1000_PHY_SPEC_CTRL:
@@ -4200,10 +4337,9 @@
 			case PHY_CTRL:
 				if (mii_reg & MII_CR_POWER_DOWN)
 					break;
-				if (netif_running(adapter->netdev)) {
-					e1000_down(adapter);
-					e1000_up(adapter);
-				} else
+				if (netif_running(adapter->netdev))
+					e1000_reinit_locked(adapter);
+				else
 					e1000_reset(adapter);
 				break;
 			}
@@ -4277,18 +4413,21 @@
 		ctrl |= E1000_CTRL_VME;
 		E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
 
+		if (adapter->hw.mac_type != e1000_ich8lan) {
 		/* enable VLAN receive filtering */
 		rctl = E1000_READ_REG(&adapter->hw, RCTL);
 		rctl |= E1000_RCTL_VFE;
 		rctl &= ~E1000_RCTL_CFIEN;
 		E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
 		e1000_update_mng_vlan(adapter);
+		}
 	} else {
 		/* disable VLAN tag insert/strip */
 		ctrl = E1000_READ_REG(&adapter->hw, CTRL);
 		ctrl &= ~E1000_CTRL_VME;
 		E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
 
+		if (adapter->hw.mac_type != e1000_ich8lan) {
 		/* disable VLAN filtering */
 		rctl = E1000_READ_REG(&adapter->hw, RCTL);
 		rctl &= ~E1000_RCTL_VFE;
@@ -4297,6 +4436,7 @@
 			e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
 			adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
 		}
+		}
 	}
 
 	e1000_irq_enable(adapter);
@@ -4458,12 +4598,16 @@
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	uint32_t ctrl, ctrl_ext, rctl, manc, status;
 	uint32_t wufc = adapter->wol;
+#ifdef CONFIG_PM
 	int retval = 0;
+#endif
 
 	netif_device_detach(netdev);
 
-	if (netif_running(netdev))
+	if (netif_running(netdev)) {
+		WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
 		e1000_down(adapter);
+	}
 
 #ifdef CONFIG_PM
 	/* Implement our own version of pci_save_state(pdev) because pci-
@@ -4521,7 +4665,9 @@
 		pci_enable_wake(pdev, PCI_D3cold, 0);
 	}
 
+	/* FIXME: this code is incorrect for PCI Express */
 	if (adapter->hw.mac_type >= e1000_82540 &&
+	   adapter->hw.mac_type != e1000_ich8lan &&
 	   adapter->hw.media_type == e1000_media_type_copper) {
 		manc = E1000_READ_REG(&adapter->hw, MANC);
 		if (manc & E1000_MANC_SMBUS_EN) {
@@ -4532,6 +4678,9 @@
 		}
 	}
 
+	if (adapter->hw.phy_type == e1000_phy_igp_3)
+		e1000_phy_powerdown_workaround(&adapter->hw);
+
 	/* Release control of h/w to f/w.  If f/w is AMT enabled, this
 	 * would have already happened in close and is redundant. */
 	e1000_release_hw_control(adapter);
@@ -4567,7 +4716,9 @@
 
 	netif_device_attach(netdev);
 
+	/* FIXME: this code is incorrect for PCI Express */
 	if (adapter->hw.mac_type >= e1000_82540 &&
+	   adapter->hw.mac_type != e1000_ich8lan &&
 	   adapter->hw.media_type == e1000_media_type_copper) {
 		manc = E1000_READ_REG(&adapter->hw, MANC);
 		manc &= ~(E1000_MANC_ARP_EN);
diff --git a/drivers/net/e1000/e1000_osdep.h b/drivers/net/e1000/e1000_osdep.h
index 048d052..2d3e8b0 100644
--- a/drivers/net/e1000/e1000_osdep.h
+++ b/drivers/net/e1000/e1000_osdep.h
@@ -127,4 +127,17 @@
 
 #define E1000_WRITE_FLUSH(a) E1000_READ_REG(a, STATUS)
 
+#define E1000_WRITE_ICH8_REG(a, reg, value) ( \
+    writel((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH8_REG(a, reg) ( \
+    readl((a)->flash_address + reg))
+
+#define E1000_WRITE_ICH8_REG16(a, reg, value) ( \
+    writew((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH8_REG16(a, reg) ( \
+    readw((a)->flash_address + reg))
+
+
 #endif /* _E1000_OSDEP_H_ */
diff --git a/drivers/net/e1000/e1000_param.c b/drivers/net/e1000/e1000_param.c
index e55f896..0ef4131 100644
--- a/drivers/net/e1000/e1000_param.c
+++ b/drivers/net/e1000/e1000_param.c
@@ -45,6 +45,16 @@
  */
 
 #define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET }
+/* Module Parameters are always initialized to -1, so that the driver
+ * can tell the difference between no user specified value or the
+ * user asking for the default value.
+ * The true default values are loaded in when e1000_check_options is called.
+ *
+ * This is a GCC extension to ANSI C.
+ * See the item "Labeled Elements in Initializers" in the section
+ * "Extensions to the C Language Family" of the GCC documentation.
+ */
+
 #define E1000_PARAM(X, desc) \
 	static int __devinitdata X[E1000_MAX_NIC+1] = E1000_PARAM_INIT; \
 	static int num_##X = 0; \
@@ -183,6 +193,24 @@
 
 E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate");
 
+/* Enable Smart Power Down of the PHY
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 0 (disabled)
+ */
+
+E1000_PARAM(SmartPowerDownEnable, "Enable PHY smart power down");
+
+/* Enable Kumeran Lock Loss workaround
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 1 (enabled)
+ */
+
+E1000_PARAM(KumeranLockLoss, "Enable Kumeran lock loss workaround");
+
 #define AUTONEG_ADV_DEFAULT  0x2F
 #define AUTONEG_ADV_MASK     0x2F
 #define FLOW_CONTROL_DEFAULT FLOW_CONTROL_FULL
@@ -296,6 +324,7 @@
 		DPRINTK(PROBE, NOTICE,
 		       "Warning: no configuration for board #%i\n", bd);
 		DPRINTK(PROBE, NOTICE, "Using defaults for all values\n");
+		bd = E1000_MAX_NIC;
 	}
 
 	{ /* Transmit Descriptor Count */
@@ -313,14 +342,9 @@
 		opt.arg.r.max = mac_type < e1000_82544 ?
 			E1000_MAX_TXD : E1000_MAX_82544_TXD;
 
-		if (num_TxDescriptors > bd) {
-			tx_ring->count = TxDescriptors[bd];
-			e1000_validate_option(&tx_ring->count, &opt, adapter);
-			E1000_ROUNDUP(tx_ring->count,
-						REQ_TX_DESCRIPTOR_MULTIPLE);
-		} else {
-			tx_ring->count = opt.def;
-		}
+		tx_ring->count = TxDescriptors[bd];
+		e1000_validate_option(&tx_ring->count, &opt, adapter);
+		E1000_ROUNDUP(tx_ring->count, REQ_TX_DESCRIPTOR_MULTIPLE);
 		for (i = 0; i < adapter->num_tx_queues; i++)
 			tx_ring[i].count = tx_ring->count;
 	}
@@ -339,14 +363,9 @@
 		opt.arg.r.max = mac_type < e1000_82544 ? E1000_MAX_RXD :
 			E1000_MAX_82544_RXD;
 
-		if (num_RxDescriptors > bd) {
-			rx_ring->count = RxDescriptors[bd];
-			e1000_validate_option(&rx_ring->count, &opt, adapter);
-			E1000_ROUNDUP(rx_ring->count,
-						REQ_RX_DESCRIPTOR_MULTIPLE);
-		} else {
-			rx_ring->count = opt.def;
-		}
+		rx_ring->count = RxDescriptors[bd];
+		e1000_validate_option(&rx_ring->count, &opt, adapter);
+		E1000_ROUNDUP(rx_ring->count, REQ_RX_DESCRIPTOR_MULTIPLE);
 		for (i = 0; i < adapter->num_rx_queues; i++)
 			rx_ring[i].count = rx_ring->count;
 	}
@@ -358,13 +377,9 @@
 			.def  = OPTION_ENABLED
 		};
 
-		if (num_XsumRX > bd) {
-			int rx_csum = XsumRX[bd];
-			e1000_validate_option(&rx_csum, &opt, adapter);
-			adapter->rx_csum = rx_csum;
-		} else {
-			adapter->rx_csum = opt.def;
-		}
+		int rx_csum = XsumRX[bd];
+		e1000_validate_option(&rx_csum, &opt, adapter);
+		adapter->rx_csum = rx_csum;
 	}
 	{ /* Flow Control */
 
@@ -384,13 +399,9 @@
 					 .p = fc_list }}
 		};
 
-		if (num_FlowControl > bd) {
-			int fc = FlowControl[bd];
-			e1000_validate_option(&fc, &opt, adapter);
-			adapter->hw.fc = adapter->hw.original_fc = fc;
-		} else {
-			adapter->hw.fc = adapter->hw.original_fc = opt.def;
-		}
+		int fc = FlowControl[bd];
+		e1000_validate_option(&fc, &opt, adapter);
+		adapter->hw.fc = adapter->hw.original_fc = fc;
 	}
 	{ /* Transmit Interrupt Delay */
 		struct e1000_option opt = {
@@ -402,13 +413,8 @@
 					 .max = MAX_TXDELAY }}
 		};
 
-		if (num_TxIntDelay > bd) {
-			adapter->tx_int_delay = TxIntDelay[bd];
-			e1000_validate_option(&adapter->tx_int_delay, &opt,
-								adapter);
-		} else {
-			adapter->tx_int_delay = opt.def;
-		}
+		adapter->tx_int_delay = TxIntDelay[bd];
+		e1000_validate_option(&adapter->tx_int_delay, &opt, adapter);
 	}
 	{ /* Transmit Absolute Interrupt Delay */
 		struct e1000_option opt = {
@@ -420,13 +426,9 @@
 					 .max = MAX_TXABSDELAY }}
 		};
 
-		if (num_TxAbsIntDelay > bd) {
-			adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
-			e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
-								adapter);
-		} else {
-			adapter->tx_abs_int_delay = opt.def;
-		}
+		adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
+		e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
+		                      adapter);
 	}
 	{ /* Receive Interrupt Delay */
 		struct e1000_option opt = {
@@ -438,13 +440,8 @@
 					 .max = MAX_RXDELAY }}
 		};
 
-		if (num_RxIntDelay > bd) {
-			adapter->rx_int_delay = RxIntDelay[bd];
-			e1000_validate_option(&adapter->rx_int_delay, &opt,
-								adapter);
-		} else {
-			adapter->rx_int_delay = opt.def;
-		}
+		adapter->rx_int_delay = RxIntDelay[bd];
+		e1000_validate_option(&adapter->rx_int_delay, &opt, adapter);
 	}
 	{ /* Receive Absolute Interrupt Delay */
 		struct e1000_option opt = {
@@ -456,13 +453,9 @@
 					 .max = MAX_RXABSDELAY }}
 		};
 
-		if (num_RxAbsIntDelay > bd) {
-			adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
-			e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
-								adapter);
-		} else {
-			adapter->rx_abs_int_delay = opt.def;
-		}
+		adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
+		e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
+		                      adapter);
 	}
 	{ /* Interrupt Throttling Rate */
 		struct e1000_option opt = {
@@ -474,26 +467,44 @@
 					 .max = MAX_ITR }}
 		};
 
-		if (num_InterruptThrottleRate > bd) {
-			adapter->itr = InterruptThrottleRate[bd];
-			switch (adapter->itr) {
-			case 0:
-				DPRINTK(PROBE, INFO, "%s turned off\n",
-					opt.name);
-				break;
-			case 1:
-				DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
-					opt.name);
-				break;
-			default:
-				e1000_validate_option(&adapter->itr, &opt,
-					adapter);
-				break;
-			}
-		} else {
-			adapter->itr = opt.def;
+		adapter->itr = InterruptThrottleRate[bd];
+		switch (adapter->itr) {
+		case 0:
+			DPRINTK(PROBE, INFO, "%s turned off\n", opt.name);
+			break;
+		case 1:
+			DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
+				opt.name);
+			break;
+		default:
+			e1000_validate_option(&adapter->itr, &opt, adapter);
+			break;
 		}
 	}
+	{ /* Smart Power Down */
+		struct e1000_option opt = {
+			.type = enable_option,
+			.name = "PHY Smart Power Down",
+			.err  = "defaulting to Disabled",
+			.def  = OPTION_DISABLED
+		};
+
+		int spd = SmartPowerDownEnable[bd];
+		e1000_validate_option(&spd, &opt, adapter);
+		adapter->smart_power_down = spd;
+	}
+	{ /* Kumeran Lock Loss Workaround */
+		struct e1000_option opt = {
+			.type = enable_option,
+			.name = "Kumeran Lock Loss Workaround",
+			.err  = "defaulting to Enabled",
+			.def  = OPTION_ENABLED
+		};
+
+			int kmrn_lock_loss = KumeranLockLoss[bd];
+			e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
+			adapter->hw.kmrn_lock_loss_workaround_disabled = !kmrn_lock_loss;
+	}
 
 	switch (adapter->hw.media_type) {
 	case e1000_media_type_fiber:
@@ -519,17 +530,18 @@
 e1000_check_fiber_options(struct e1000_adapter *adapter)
 {
 	int bd = adapter->bd_number;
-	if (num_Speed > bd) {
+	bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
+	if ((Speed[bd] != OPTION_UNSET)) {
 		DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, "
 		       "parameter ignored\n");
 	}
 
-	if (num_Duplex > bd) {
+	if ((Duplex[bd] != OPTION_UNSET)) {
 		DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, "
 		       "parameter ignored\n");
 	}
 
-	if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) {
+	if ((AutoNeg[bd] != OPTION_UNSET) && (AutoNeg[bd] != 0x20)) {
 		DPRINTK(PROBE, INFO, "AutoNeg other than 1000/Full is "
 				 "not valid for fiber adapters, "
 				 "parameter ignored\n");
@@ -548,6 +560,7 @@
 {
 	int speed, dplx, an;
 	int bd = adapter->bd_number;
+	bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
 
 	{ /* Speed */
 		struct e1000_opt_list speed_list[] = {{          0, "" },
@@ -564,12 +577,8 @@
 					 .p = speed_list }}
 		};
 
-		if (num_Speed > bd) {
-			speed = Speed[bd];
-			e1000_validate_option(&speed, &opt, adapter);
-		} else {
-			speed = opt.def;
-		}
+		speed = Speed[bd];
+		e1000_validate_option(&speed, &opt, adapter);
 	}
 	{ /* Duplex */
 		struct e1000_opt_list dplx_list[] = {{           0, "" },
@@ -591,15 +600,11 @@
 			        "Speed/Duplex/AutoNeg parameter ignored.\n");
 			return;
 		}
-		if (num_Duplex > bd) {
-			dplx = Duplex[bd];
-			e1000_validate_option(&dplx, &opt, adapter);
-		} else {
-			dplx = opt.def;
-		}
+		dplx = Duplex[bd];
+		e1000_validate_option(&dplx, &opt, adapter);
 	}
 
-	if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) {
+	if (AutoNeg[bd] != OPTION_UNSET && (speed != 0 || dplx != 0)) {
 		DPRINTK(PROBE, INFO,
 		       "AutoNeg specified along with Speed or Duplex, "
 		       "parameter ignored\n");
@@ -648,19 +653,15 @@
 					 .p = an_list }}
 		};
 
-		if (num_AutoNeg > bd) {
-			an = AutoNeg[bd];
-			e1000_validate_option(&an, &opt, adapter);
-		} else {
-			an = opt.def;
-		}
+		an = AutoNeg[bd];
+		e1000_validate_option(&an, &opt, adapter);
 		adapter->hw.autoneg_advertised = an;
 	}
 
 	switch (speed + dplx) {
 	case 0:
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
-		if ((num_Speed > bd) && (speed != 0 || dplx != 0))
+		if (Speed[bd] != OPTION_UNSET || Duplex[bd] != OPTION_UNSET)
 			DPRINTK(PROBE, INFO,
 			       "Speed and duplex autonegotiation enabled\n");
 		break;
diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c
index 037d870..ad81ec6 100644
--- a/drivers/net/forcedeth.c
+++ b/drivers/net/forcedeth.c
@@ -1495,7 +1495,7 @@
 	np->tx_skbuff[nr] = skb;
 
 #ifdef NETIF_F_TSO
-	if (skb_shinfo(skb)->gso_size)
+	if (skb_is_gso(skb))
 		tx_flags_extra = NV_TX2_TSO | (skb_shinfo(skb)->gso_size << NV_TX2_TSO_SHIFT);
 	else
 #endif
diff --git a/drivers/net/irda/ali-ircc.c b/drivers/net/irda/ali-ircc.c
index bf1fca5..e3c8cd5 100644
--- a/drivers/net/irda/ali-ircc.c
+++ b/drivers/net/irda/ali-ircc.c
@@ -146,7 +146,7 @@
 {
 	ali_chip_t *chip;
 	chipio_t info;
-	int ret = -ENODEV;
+	int ret;
 	int cfg, cfg_base;
 	int reg, revision;
 	int i = 0;
@@ -160,6 +160,7 @@
                 return ret;
         }
 
+	ret = -ENODEV;
 	
 	/* Probe for all the ALi chipsets we know about */
 	for (chip= chips; chip->name; chip++, i++) 
diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
index b91e082..7eb08d9 100644
--- a/drivers/net/ixgb/ixgb_main.c
+++ b/drivers/net/ixgb/ixgb_main.c
@@ -1173,7 +1173,7 @@
 	uint16_t ipcse, tucse, mss;
 	int err;
 
-	if(likely(skb_shinfo(skb)->gso_size)) {
+	if (likely(skb_is_gso(skb))) {
 		if (skb_header_cloned(skb)) {
 			err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
 			if (err)
diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c
index 43fef7d..997cbce 100644
--- a/drivers/net/loopback.c
+++ b/drivers/net/loopback.c
@@ -139,7 +139,7 @@
 #endif
 
 #ifdef LOOPBACK_TSO
-	if (skb_shinfo(skb)->gso_size) {
+	if (skb_is_gso(skb)) {
 		BUG_ON(skb->protocol != htons(ETH_P_IP));
 		BUG_ON(skb->nh.iph->protocol != IPPROTO_TCP);
 
diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c
index f4c8fd3..ee1de97 100644
--- a/drivers/net/myri10ge/myri10ge.c
+++ b/drivers/net/myri10ge/myri10ge.c
@@ -2116,7 +2116,7 @@
 		}
 		idx = (idx + 1) & tx->mask;
 	} while (idx != last_idx);
-	if (skb_shinfo(skb)->gso_size) {
+	if (skb_is_gso(skb)) {
 		printk(KERN_ERR
 		       "myri10ge: %s: TSO but wanted to linearize?!?!?\n",
 		       mgp->dev->name);
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 418f169..3109376 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1159,7 +1159,7 @@
 	count = sizeof(dma_addr_t) / sizeof(u32);
 	count += skb_shinfo(skb)->nr_frags * count;
 
-	if (skb_shinfo(skb)->gso_size)
+	if (skb_is_gso(skb))
 		++count;
 
 	if (skb->ip_summed == CHECKSUM_HW)
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index f645921..ce6f3be 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -10078,6 +10078,8 @@
 	static struct pci_device_id write_reorder_chipsets[] = {
 		{ PCI_DEVICE(PCI_VENDOR_ID_AMD,
 		             PCI_DEVICE_ID_AMD_FE_GATE_700C) },
+		{ PCI_DEVICE(PCI_VENDOR_ID_AMD,
+		             PCI_DEVICE_ID_AMD_8131_BRIDGE) },
 		{ PCI_DEVICE(PCI_VENDOR_ID_VIA,
 			     PCI_DEVICE_ID_VIA_8385_0) },
 		{ },
diff --git a/drivers/net/typhoon.c b/drivers/net/typhoon.c
index 063816f2..4103c37 100644
--- a/drivers/net/typhoon.c
+++ b/drivers/net/typhoon.c
@@ -805,7 +805,7 @@
 	 * If problems develop with TSO, check this first.
 	 */
 	numDesc = skb_shinfo(skb)->nr_frags + 1;
-	if(skb_tso_size(skb))
+	if (skb_is_gso(skb))
 		numDesc++;
 
 	/* When checking for free space in the ring, we need to also
@@ -845,7 +845,7 @@
 				TYPHOON_TX_PF_VLAN_TAG_SHIFT);
 	}
 
-	if(skb_tso_size(skb)) {
+	if (skb_is_gso(skb)) {
 		first_txd->processFlags |= TYPHOON_TX_PF_TCP_SEGMENT;
 		first_txd->numDesc++;
 
diff --git a/drivers/pci/hotplug/Kconfig b/drivers/pci/hotplug/Kconfig
index 222a1cc..d305d21 100644
--- a/drivers/pci/hotplug/Kconfig
+++ b/drivers/pci/hotplug/Kconfig
@@ -77,7 +77,7 @@
 
 config HOTPLUG_PCI_ACPI
 	tristate "ACPI PCI Hotplug driver"
-	depends on ACPI && HOTPLUG_PCI
+	depends on ACPI_DOCK && HOTPLUG_PCI
 	help
 	  Say Y here if you have a system that supports PCI Hotplug using
 	  ACPI.
diff --git a/drivers/s390/net/qeth_main.c b/drivers/s390/net/qeth_main.c
index 8e8963f..329e12c 100644
--- a/drivers/s390/net/qeth_main.c
+++ b/drivers/s390/net/qeth_main.c
@@ -4457,7 +4457,7 @@
 	queue = card->qdio.out_qs
 		[qeth_get_priority_queue(card, skb, ipv, cast_type)];
 
-	if (skb_shinfo(skb)->gso_size)
+	if (skb_is_gso(skb))
 		large_send = card->options.large_send;
 
 	/*are we able to do TSO ? If so ,prepare and send it from here */
diff --git a/include/acpi/aclocal.h b/include/acpi/aclocal.h
index 7010fea..a4d0e73 100644
--- a/include/acpi/aclocal.h
+++ b/include/acpi/aclocal.h
@@ -127,7 +127,7 @@
 
 /* This Thread ID means that the mutex is not in use (unlocked) */
 
-#define ACPI_MUTEX_NOT_ACQUIRED         (u32) -1
+#define ACPI_MUTEX_NOT_ACQUIRED         (acpi_thread_id) 0
 
 /* Table for the global mutexes */
 
diff --git a/include/acpi/platform/aclinux.h b/include/acpi/platform/aclinux.h
index 3f853ca..1cb51bf 100644
--- a/include/acpi/platform/aclinux.h
+++ b/include/acpi/platform/aclinux.h
@@ -59,6 +59,7 @@
 #include <asm/acpi.h>
 #include <linux/slab.h>
 #include <linux/spinlock_types.h>
+#include <asm/current.h>
 
 /* Host-dependent types and defines */
 
@@ -100,8 +101,8 @@
 
 #define acpi_cpu_flags unsigned long
 
-#define acpi_thread_id u32
+#define acpi_thread_id struct task_struct *
 
-static inline acpi_thread_id acpi_os_get_thread_id(void) { return 0; }
+static inline acpi_thread_id acpi_os_get_thread_id(void) { return current; }
 
 #endif				/* __ACLINUX_H__ */
diff --git a/include/asm-i386/atomic.h b/include/asm-i386/atomic.h
index 4f061fa..51a1662 100644
--- a/include/asm-i386/atomic.h
+++ b/include/asm-i386/atomic.h
@@ -46,8 +46,8 @@
 {
 	__asm__ __volatile__(
 		LOCK_PREFIX "addl %1,%0"
-		:"=m" (v->counter)
-		:"ir" (i), "m" (v->counter));
+		:"+m" (v->counter)
+		:"ir" (i));
 }
 
 /**
@@ -61,8 +61,8 @@
 {
 	__asm__ __volatile__(
 		LOCK_PREFIX "subl %1,%0"
-		:"=m" (v->counter)
-		:"ir" (i), "m" (v->counter));
+		:"+m" (v->counter)
+		:"ir" (i));
 }
 
 /**
@@ -80,8 +80,8 @@
 
 	__asm__ __volatile__(
 		LOCK_PREFIX "subl %2,%0; sete %1"
-		:"=m" (v->counter), "=qm" (c)
-		:"ir" (i), "m" (v->counter) : "memory");
+		:"+m" (v->counter), "=qm" (c)
+		:"ir" (i) : "memory");
 	return c;
 }
 
@@ -95,8 +95,7 @@
 {
 	__asm__ __volatile__(
 		LOCK_PREFIX "incl %0"
-		:"=m" (v->counter)
-		:"m" (v->counter));
+		:"+m" (v->counter));
 }
 
 /**
@@ -109,8 +108,7 @@
 {
 	__asm__ __volatile__(
 		LOCK_PREFIX "decl %0"
-		:"=m" (v->counter)
-		:"m" (v->counter));
+		:"+m" (v->counter));
 }
 
 /**
@@ -127,8 +125,8 @@
 
 	__asm__ __volatile__(
 		LOCK_PREFIX "decl %0; sete %1"
-		:"=m" (v->counter), "=qm" (c)
-		:"m" (v->counter) : "memory");
+		:"+m" (v->counter), "=qm" (c)
+		: : "memory");
 	return c != 0;
 }
 
@@ -146,8 +144,8 @@
 
 	__asm__ __volatile__(
 		LOCK_PREFIX "incl %0; sete %1"
-		:"=m" (v->counter), "=qm" (c)
-		:"m" (v->counter) : "memory");
+		:"+m" (v->counter), "=qm" (c)
+		: : "memory");
 	return c != 0;
 }
 
@@ -166,8 +164,8 @@
 
 	__asm__ __volatile__(
 		LOCK_PREFIX "addl %2,%0; sets %1"
-		:"=m" (v->counter), "=qm" (c)
-		:"ir" (i), "m" (v->counter) : "memory");
+		:"+m" (v->counter), "=qm" (c)
+		:"ir" (i) : "memory");
 	return c;
 }
 
diff --git a/include/asm-i386/futex.h b/include/asm-i386/futex.h
index 7b8ceef..946d97c 100644
--- a/include/asm-i386/futex.h
+++ b/include/asm-i386/futex.h
@@ -20,8 +20,8 @@
 	.align	8\n\
 	.long	1b,3b\n\
 	.previous"						\
-	: "=r" (oldval), "=r" (ret), "=m" (*uaddr)		\
-	: "i" (-EFAULT), "m" (*uaddr), "0" (oparg), "1" (0))
+	: "=r" (oldval), "=r" (ret), "+m" (*uaddr)		\
+	: "i" (-EFAULT), "0" (oparg), "1" (0))
 
 #define __futex_atomic_op2(insn, ret, oldval, uaddr, oparg) \
   __asm__ __volatile (						\
@@ -38,9 +38,9 @@
 	.align	8\n\
 	.long	1b,4b,2b,4b\n\
 	.previous"						\
-	: "=&a" (oldval), "=&r" (ret), "=m" (*uaddr),		\
+	: "=&a" (oldval), "=&r" (ret), "+m" (*uaddr),		\
 	  "=&r" (tem)						\
-	: "r" (oparg), "i" (-EFAULT), "m" (*uaddr), "1" (0))
+	: "r" (oparg), "i" (-EFAULT), "1" (0))
 
 static inline int
 futex_atomic_op_inuser (int encoded_op, int __user *uaddr)
@@ -123,7 +123,7 @@
 		"	.long   1b,3b				\n"
 		"	.previous				\n"
 
-		: "=a" (oldval), "=m" (*uaddr)
+		: "=a" (oldval), "+m" (*uaddr)
 		: "i" (-EFAULT), "r" (newval), "0" (oldval)
 		: "memory"
 	);
diff --git a/include/asm-i386/local.h b/include/asm-i386/local.h
index 3b4998c..12060e2 100644
--- a/include/asm-i386/local.h
+++ b/include/asm-i386/local.h
@@ -17,32 +17,30 @@
 {
 	__asm__ __volatile__(
 		"incl %0"
-		:"=m" (v->counter)
-		:"m" (v->counter));
+		:"+m" (v->counter));
 }
 
 static __inline__ void local_dec(local_t *v)
 {
 	__asm__ __volatile__(
 		"decl %0"
-		:"=m" (v->counter)
-		:"m" (v->counter));
+		:"+m" (v->counter));
 }
 
 static __inline__ void local_add(long i, local_t *v)
 {
 	__asm__ __volatile__(
 		"addl %1,%0"
-		:"=m" (v->counter)
-		:"ir" (i), "m" (v->counter));
+		:"+m" (v->counter)
+		:"ir" (i));
 }
 
 static __inline__ void local_sub(long i, local_t *v)
 {
 	__asm__ __volatile__(
 		"subl %1,%0"
-		:"=m" (v->counter)
-		:"ir" (i), "m" (v->counter));
+		:"+m" (v->counter)
+		:"ir" (i));
 }
 
 /* On x86, these are no better than the atomic variants. */
diff --git a/include/asm-i386/posix_types.h b/include/asm-i386/posix_types.h
index 4e47ed0..133e31e 100644
--- a/include/asm-i386/posix_types.h
+++ b/include/asm-i386/posix_types.h
@@ -51,12 +51,12 @@
 #undef	__FD_SET
 #define __FD_SET(fd,fdsetp) \
 		__asm__ __volatile__("btsl %1,%0": \
-			"=m" (*(__kernel_fd_set *) (fdsetp)):"r" ((int) (fd)))
+			"+m" (*(__kernel_fd_set *) (fdsetp)):"r" ((int) (fd)))
 
 #undef	__FD_CLR
 #define __FD_CLR(fd,fdsetp) \
 		__asm__ __volatile__("btrl %1,%0": \
-			"=m" (*(__kernel_fd_set *) (fdsetp)):"r" ((int) (fd)))
+			"+m" (*(__kernel_fd_set *) (fdsetp)):"r" ((int) (fd)))
 
 #undef	__FD_ISSET
 #define __FD_ISSET(fd,fdsetp) (__extension__ ({ \
diff --git a/include/asm-i386/rwlock.h b/include/asm-i386/rwlock.h
index 94f0019..96b0bef 100644
--- a/include/asm-i386/rwlock.h
+++ b/include/asm-i386/rwlock.h
@@ -37,7 +37,7 @@
 			"popl %%eax\n\t" \
 			"1:\n", \
 			"subl $1,%0\n\t", \
-			"=m" (*(volatile int *)rw) : : "memory")
+			"+m" (*(volatile int *)rw) : : "memory")
 
 #define __build_read_lock(rw, helper)	do { \
 						if (__builtin_constant_p(rw)) \
@@ -63,7 +63,7 @@
 			"popl %%eax\n\t" \
 			"1:\n", \
 			"subl $" RW_LOCK_BIAS_STR ",%0\n\t", \
-			"=m" (*(volatile int *)rw) : : "memory")
+			"+m" (*(volatile int *)rw) : : "memory")
 
 #define __build_write_lock(rw, helper)	do { \
 						if (__builtin_constant_p(rw)) \
diff --git a/include/asm-i386/rwsem.h b/include/asm-i386/rwsem.h
index 2f07601..43113f5 100644
--- a/include/asm-i386/rwsem.h
+++ b/include/asm-i386/rwsem.h
@@ -111,8 +111,8 @@
 		"  jmp       1b\n"
 		LOCK_SECTION_END
 		"# ending down_read\n\t"
-		: "=m"(sem->count)
-		: "a"(sem), "m"(sem->count)
+		: "+m" (sem->count)
+		: "a" (sem)
 		: "memory", "cc");
 }
 
@@ -133,8 +133,8 @@
 		"  jnz	     1b\n\t"
 		"2:\n\t"
 		"# ending __down_read_trylock\n\t"
-		: "+m"(sem->count), "=&a"(result), "=&r"(tmp)
-		: "i"(RWSEM_ACTIVE_READ_BIAS)
+		: "+m" (sem->count), "=&a" (result), "=&r" (tmp)
+		: "i" (RWSEM_ACTIVE_READ_BIAS)
 		: "memory", "cc");
 	return result>=0 ? 1 : 0;
 }
@@ -161,8 +161,8 @@
 		"  jmp       1b\n"
 		LOCK_SECTION_END
 		"# ending down_write"
-		: "=m"(sem->count), "=d"(tmp)
-		: "a"(sem), "1"(tmp), "m"(sem->count)
+		: "+m" (sem->count), "=d" (tmp)
+		: "a" (sem), "1" (tmp)
 		: "memory", "cc");
 }
 
@@ -205,8 +205,8 @@
 		"  jmp       1b\n"
 		LOCK_SECTION_END
 		"# ending __up_read\n"
-		: "=m"(sem->count), "=d"(tmp)
-		: "a"(sem), "1"(tmp), "m"(sem->count)
+		: "+m" (sem->count), "=d" (tmp)
+		: "a" (sem), "1" (tmp)
 		: "memory", "cc");
 }
 
@@ -231,8 +231,8 @@
 		"  jmp       1b\n"
 		LOCK_SECTION_END
 		"# ending __up_write\n"
-		: "=m"(sem->count)
-		: "a"(sem), "i"(-RWSEM_ACTIVE_WRITE_BIAS), "m"(sem->count)
+		: "+m" (sem->count)
+		: "a" (sem), "i" (-RWSEM_ACTIVE_WRITE_BIAS)
 		: "memory", "cc", "edx");
 }
 
@@ -256,8 +256,8 @@
 		"  jmp       1b\n"
 		LOCK_SECTION_END
 		"# ending __downgrade_write\n"
-		: "=m"(sem->count)
-		: "a"(sem), "i"(-RWSEM_WAITING_BIAS), "m"(sem->count)
+		: "+m" (sem->count)
+		: "a" (sem), "i" (-RWSEM_WAITING_BIAS)
 		: "memory", "cc");
 }
 
@@ -268,8 +268,8 @@
 {
 	__asm__ __volatile__(
 LOCK_PREFIX	"addl %1,%0"
-		: "=m"(sem->count)
-		: "ir"(delta), "m"(sem->count));
+		: "+m" (sem->count)
+		: "ir" (delta));
 }
 
 /*
@@ -280,10 +280,9 @@
 	int tmp = delta;
 
 	__asm__ __volatile__(
-LOCK_PREFIX	"xadd %0,(%2)"
-		: "+r"(tmp), "=m"(sem->count)
-		: "r"(sem), "m"(sem->count)
-		: "memory");
+LOCK_PREFIX	"xadd %0,%1"
+		: "+r" (tmp), "+m" (sem->count)
+		: : "memory");
 
 	return tmp+delta;
 }
diff --git a/include/asm-i386/semaphore.h b/include/asm-i386/semaphore.h
index f7a0f31..d51e800 100644
--- a/include/asm-i386/semaphore.h
+++ b/include/asm-i386/semaphore.h
@@ -107,7 +107,7 @@
 		"call __down_failed\n\t"
 		"jmp 1b\n"
 		LOCK_SECTION_END
-		:"=m" (sem->count)
+		:"+m" (sem->count)
 		:
 		:"memory","ax");
 }
@@ -132,7 +132,7 @@
 		"call __down_failed_interruptible\n\t"
 		"jmp 1b\n"
 		LOCK_SECTION_END
-		:"=a" (result), "=m" (sem->count)
+		:"=a" (result), "+m" (sem->count)
 		:
 		:"memory");
 	return result;
@@ -157,7 +157,7 @@
 		"call __down_failed_trylock\n\t"
 		"jmp 1b\n"
 		LOCK_SECTION_END
-		:"=a" (result), "=m" (sem->count)
+		:"=a" (result), "+m" (sem->count)
 		:
 		:"memory");
 	return result;
@@ -182,7 +182,7 @@
 		"jmp 1b\n"
 		LOCK_SECTION_END
 		".subsection 0\n"
-		:"=m" (sem->count)
+		:"+m" (sem->count)
 		:
 		:"memory","ax");
 }
diff --git a/include/asm-i386/spinlock.h b/include/asm-i386/spinlock.h
index 87c40f8..d816c62 100644
--- a/include/asm-i386/spinlock.h
+++ b/include/asm-i386/spinlock.h
@@ -65,7 +65,7 @@
 	alternative_smp(
 		__raw_spin_lock_string,
 		__raw_spin_lock_string_up,
-		"=m" (lock->slock) : : "memory");
+		"+m" (lock->slock) : : "memory");
 }
 
 /*
@@ -79,7 +79,7 @@
 	alternative_smp(
 		__raw_spin_lock_string_flags,
 		__raw_spin_lock_string_up,
-		"=m" (lock->slock) : "r" (flags) : "memory");
+		"+m" (lock->slock) : "r" (flags) : "memory");
 }
 #endif
 
@@ -88,7 +88,7 @@
 	char oldval;
 	__asm__ __volatile__(
 		"xchgb %b0,%1"
-		:"=q" (oldval), "=m" (lock->slock)
+		:"=q" (oldval), "+m" (lock->slock)
 		:"0" (0) : "memory");
 	return oldval > 0;
 }
@@ -104,7 +104,7 @@
 
 #define __raw_spin_unlock_string \
 	"movb $1,%0" \
-		:"=m" (lock->slock) : : "memory"
+		:"+m" (lock->slock) : : "memory"
 
 
 static inline void __raw_spin_unlock(raw_spinlock_t *lock)
@@ -118,7 +118,7 @@
 
 #define __raw_spin_unlock_string \
 	"xchgb %b0, %1" \
-		:"=q" (oldval), "=m" (lock->slock) \
+		:"=q" (oldval), "+m" (lock->slock) \
 		:"0" (oldval) : "memory"
 
 static inline void __raw_spin_unlock(raw_spinlock_t *lock)
@@ -199,13 +199,13 @@
 
 static inline void __raw_read_unlock(raw_rwlock_t *rw)
 {
-	asm volatile(LOCK_PREFIX "incl %0" :"=m" (rw->lock) : : "memory");
+	asm volatile(LOCK_PREFIX "incl %0" :"+m" (rw->lock) : : "memory");
 }
 
 static inline void __raw_write_unlock(raw_rwlock_t *rw)
 {
 	asm volatile(LOCK_PREFIX "addl $" RW_LOCK_BIAS_STR ", %0"
-				 : "=m" (rw->lock) : : "memory");
+				 : "+m" (rw->lock) : : "memory");
 }
 
 #endif /* __ASM_SPINLOCK_H */
diff --git a/include/asm-i386/thread_info.h b/include/asm-i386/thread_info.h
index 2833fa2..54d6d7a 100644
--- a/include/asm-i386/thread_info.h
+++ b/include/asm-i386/thread_info.h
@@ -140,6 +140,8 @@
 #define TIF_SECCOMP		8	/* secure computing */
 #define TIF_RESTORE_SIGMASK	9	/* restore signal mask in do_signal() */
 #define TIF_MEMDIE		16
+#define TIF_DEBUG		17	/* uses debug registers */
+#define TIF_IO_BITMAP		18	/* uses I/O bitmap */
 
 #define _TIF_SYSCALL_TRACE	(1<<TIF_SYSCALL_TRACE)
 #define _TIF_NOTIFY_RESUME	(1<<TIF_NOTIFY_RESUME)
@@ -151,6 +153,8 @@
 #define _TIF_SYSCALL_AUDIT	(1<<TIF_SYSCALL_AUDIT)
 #define _TIF_SECCOMP		(1<<TIF_SECCOMP)
 #define _TIF_RESTORE_SIGMASK	(1<<TIF_RESTORE_SIGMASK)
+#define _TIF_DEBUG		(1<<TIF_DEBUG)
+#define _TIF_IO_BITMAP		(1<<TIF_IO_BITMAP)
 
 /* work to do on interrupt/exception return */
 #define _TIF_WORK_MASK \
@@ -159,6 +163,9 @@
 /* work to do on any return to u-space */
 #define _TIF_ALLWORK_MASK	(0x0000FFFF & ~_TIF_SECCOMP)
 
+/* flags to check in __switch_to() */
+#define _TIF_WORK_CTXSW (_TIF_DEBUG|_TIF_IO_BITMAP)
+
 /*
  * Thread-synchronous status.
  *
diff --git a/include/asm-powerpc/atomic.h b/include/asm-powerpc/atomic.h
index bb3c0ab..53283e2 100644
--- a/include/asm-powerpc/atomic.h
+++ b/include/asm-powerpc/atomic.h
@@ -27,8 +27,8 @@
 	PPC405_ERR77(0,%3)
 "	stwcx.	%0,0,%3 \n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (a), "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (a), "r" (&v->counter)
 	: "cc");
 }
 
@@ -63,8 +63,8 @@
 	PPC405_ERR77(0,%3)
 "	stwcx.	%0,0,%3 \n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (a), "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (a), "r" (&v->counter)
 	: "cc");
 }
 
@@ -97,8 +97,8 @@
 	PPC405_ERR77(0,%2)
 "	stwcx.	%0,0,%2 \n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (&v->counter)
 	: "cc");
 }
 
@@ -141,8 +141,8 @@
 	PPC405_ERR77(0,%2)\
 "	stwcx.	%0,0,%2\n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (&v->counter)
 	: "cc");
 }
 
@@ -253,8 +253,8 @@
 	add	%0,%2,%0\n\
 	stdcx.	%0,0,%3 \n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (a), "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (a), "r" (&v->counter)
 	: "cc");
 }
 
@@ -287,8 +287,8 @@
 	subf	%0,%2,%0\n\
 	stdcx.	%0,0,%3 \n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (a), "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (a), "r" (&v->counter)
 	: "cc");
 }
 
@@ -319,8 +319,8 @@
 	addic	%0,%0,1\n\
 	stdcx.	%0,0,%2 \n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (&v->counter)
 	: "cc");
 }
 
@@ -361,8 +361,8 @@
 	addic	%0,%0,-1\n\
 	stdcx.	%0,0,%2\n\
 	bne-	1b"
-	: "=&r" (t), "=m" (v->counter)
-	: "r" (&v->counter), "m" (v->counter)
+	: "=&r" (t), "+m" (v->counter)
+	: "r" (&v->counter)
 	: "cc");
 }
 
diff --git a/include/asm-powerpc/bitops.h b/include/asm-powerpc/bitops.h
index 76e2f08..c341063 100644
--- a/include/asm-powerpc/bitops.h
+++ b/include/asm-powerpc/bitops.h
@@ -65,8 +65,8 @@
 	PPC405_ERR77(0,%3)
 	PPC_STLCX "%0,0,%3\n"
 	"bne-	1b"
-	: "=&r"(old), "=m"(*p)
-	: "r"(mask), "r"(p), "m"(*p)
+	: "=&r" (old), "+m" (*p)
+	: "r" (mask), "r" (p)
 	: "cc" );
 }
 
@@ -82,8 +82,8 @@
 	PPC405_ERR77(0,%3)
 	PPC_STLCX "%0,0,%3\n"
 	"bne-	1b"
-	: "=&r"(old), "=m"(*p)
-	: "r"(mask), "r"(p), "m"(*p)
+	: "=&r" (old), "+m" (*p)
+	: "r" (mask), "r" (p)
 	: "cc" );
 }
 
@@ -99,8 +99,8 @@
 	PPC405_ERR77(0,%3)
 	PPC_STLCX "%0,0,%3\n"
 	"bne-	1b"
-	: "=&r"(old), "=m"(*p)
-	: "r"(mask), "r"(p), "m"(*p)
+	: "=&r" (old), "+m" (*p)
+	: "r" (mask), "r" (p)
 	: "cc" );
 }
 
@@ -179,8 +179,8 @@
 	"or	%0,%0,%2\n"
 	PPC_STLCX "%0,0,%3\n"
 	"bne-	1b"
-	: "=&r" (old), "=m" (*addr)
-	: "r" (mask), "r" (addr), "m" (*addr)
+	: "=&r" (old), "+m" (*addr)
+	: "r" (mask), "r" (addr)
 	: "cc");
 }
 
diff --git a/include/asm-powerpc/system.h b/include/asm-powerpc/system.h
index d075725..c656951 100644
--- a/include/asm-powerpc/system.h
+++ b/include/asm-powerpc/system.h
@@ -220,8 +220,8 @@
 "	stwcx.	%3,0,%2 \n\
 	bne-	1b"
 	ISYNC_ON_SMP
-	: "=&r" (prev), "=m" (*(volatile unsigned int *)p)
-	: "r" (p), "r" (val), "m" (*(volatile unsigned int *)p)
+	: "=&r" (prev), "+m" (*(volatile unsigned int *)p)
+	: "r" (p), "r" (val)
 	: "cc", "memory");
 
 	return prev;
@@ -240,8 +240,8 @@
 "	stdcx.	%3,0,%2 \n\
 	bne-	1b"
 	ISYNC_ON_SMP
-	: "=&r" (prev), "=m" (*(volatile unsigned long *)p)
-	: "r" (p), "r" (val), "m" (*(volatile unsigned long *)p)
+	: "=&r" (prev), "+m" (*(volatile unsigned long *)p)
+	: "r" (p), "r" (val)
 	: "cc", "memory");
 
 	return prev;
@@ -299,8 +299,8 @@
 	ISYNC_ON_SMP
 	"\n\
 2:"
-	: "=&r" (prev), "=m" (*p)
-	: "r" (p), "r" (old), "r" (new), "m" (*p)
+	: "=&r" (prev), "+m" (*p)
+	: "r" (p), "r" (old), "r" (new)
 	: "cc", "memory");
 
 	return prev;
@@ -322,8 +322,8 @@
 	ISYNC_ON_SMP
 	"\n\
 2:"
-	: "=&r" (prev), "=m" (*p)
-	: "r" (p), "r" (old), "r" (new), "m" (*p)
+	: "=&r" (prev), "+m" (*p)
+	: "r" (p), "r" (old), "r" (new)
 	: "cc", "memory");
 
 	return prev;
diff --git a/include/linux/blktrace_api.h b/include/linux/blktrace_api.h
index a7e8cef..7520cc1 100644
--- a/include/linux/blktrace_api.h
+++ b/include/linux/blktrace_api.h
@@ -11,7 +11,7 @@
 	BLK_TC_READ	= 1 << 0,	/* reads */
 	BLK_TC_WRITE	= 1 << 1,	/* writes */
 	BLK_TC_BARRIER	= 1 << 2,	/* barrier */
-	BLK_TC_SYNC	= 1 << 3,	/* barrier */
+	BLK_TC_SYNC	= 1 << 3,	/* sync IO */
 	BLK_TC_QUEUE	= 1 << 4,	/* queueing/merging */
 	BLK_TC_REQUEUE	= 1 << 5,	/* requeueing */
 	BLK_TC_ISSUE	= 1 << 6,	/* issue */
@@ -19,6 +19,7 @@
 	BLK_TC_FS	= 1 << 8,	/* fs requests */
 	BLK_TC_PC	= 1 << 9,	/* pc requests */
 	BLK_TC_NOTIFY	= 1 << 10,	/* special message */
+	BLK_TC_AHEAD	= 1 << 11,	/* readahead */
 
 	BLK_TC_END	= 1 << 15,	/* only 16-bits, reminder */
 };
@@ -147,7 +148,7 @@
 				    u32 what)
 {
 	struct blk_trace *bt = q->blk_trace;
-	int rw = rq->flags & 0x07;
+	int rw = rq->flags & 0x03;
 
 	if (likely(!bt))
 		return;
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 85f99f6..76cc099 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -549,6 +549,7 @@
 					 struct net_device *);
 	struct sk_buff		*(*gso_segment)(struct sk_buff *skb,
 						int features);
+	int			(*gso_send_check)(struct sk_buff *skb);
 	void			*af_packet_priv;
 	struct list_head	list;
 };
@@ -1001,13 +1002,14 @@
 
 static inline int skb_gso_ok(struct sk_buff *skb, int features)
 {
-	return net_gso_ok(features, skb_shinfo(skb)->gso_size ?
-				    skb_shinfo(skb)->gso_type : 0);
+	return net_gso_ok(features, skb_shinfo(skb)->gso_type);
 }
 
 static inline int netif_needs_gso(struct net_device *dev, struct sk_buff *skb)
 {
-	return !skb_gso_ok(skb, dev->features);
+	return skb_is_gso(skb) &&
+	       (!skb_gso_ok(skb, dev->features) ||
+		unlikely(skb->ip_summed != CHECKSUM_HW));
 }
 
 #endif /* __KERNEL__ */
diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h
index 3597b4f..0bf31b8 100644
--- a/include/linux/skbuff.h
+++ b/include/linux/skbuff.h
@@ -1455,5 +1455,10 @@
 { }
 #endif
 
+static inline int skb_is_gso(const struct sk_buff *skb)
+{
+	return skb_shinfo(skb)->gso_size;
+}
+
 #endif	/* __KERNEL__ */
 #endif	/* _LINUX_SKBUFF_H */
diff --git a/include/net/protocol.h b/include/net/protocol.h
index a225d63..c643bce 100644
--- a/include/net/protocol.h
+++ b/include/net/protocol.h
@@ -36,6 +36,7 @@
 struct net_protocol {
 	int			(*handler)(struct sk_buff *skb);
 	void			(*err_handler)(struct sk_buff *skb, u32 info);
+	int			(*gso_send_check)(struct sk_buff *skb);
 	struct sk_buff	       *(*gso_segment)(struct sk_buff *skb,
 					       int features);
 	int			no_policy;
@@ -51,6 +52,7 @@
 			       int type, int code, int offset,
 			       __u32 info);
 
+	int	(*gso_send_check)(struct sk_buff *skb);
 	struct sk_buff *(*gso_segment)(struct sk_buff *skb,
 				       int features);
 
diff --git a/include/net/tcp.h b/include/net/tcp.h
index 3cd803b..0720bdd 100644
--- a/include/net/tcp.h
+++ b/include/net/tcp.h
@@ -1086,6 +1086,7 @@
 
 extern int tcp_v4_destroy_sock(struct sock *sk);
 
+extern int tcp_v4_gso_send_check(struct sk_buff *skb);
 extern struct sk_buff *tcp_tso_segment(struct sk_buff *skb, int features);
 
 #ifdef CONFIG_PROC_FS
diff --git a/net/atm/clip.c b/net/atm/clip.c
index 121bf6f..2e62105 100644
--- a/net/atm/clip.c
+++ b/net/atm/clip.c
@@ -962,7 +962,6 @@
 
 static int __init atm_clip_init(void)
 {
-	struct proc_dir_entry *p;
 	neigh_table_init_no_netlink(&clip_tbl);
 
 	clip_tbl_hook = &clip_tbl;
@@ -972,9 +971,15 @@
 
 	setup_timer(&idle_timer, idle_timer_check, 0);
 
-	p = create_proc_entry("arp", S_IRUGO, atm_proc_root);
-	if (p)
-		p->proc_fops = &arp_seq_fops;
+#ifdef CONFIG_PROC_FS
+	{
+		struct proc_dir_entry *p;
+
+		p = create_proc_entry("arp", S_IRUGO, atm_proc_root);
+		if (p)
+			p->proc_fops = &arp_seq_fops;
+	}
+#endif
 
 	return 0;
 }
diff --git a/net/atm/ipcommon.c b/net/atm/ipcommon.c
index 4b1faca..1d3de42 100644
--- a/net/atm/ipcommon.c
+++ b/net/atm/ipcommon.c
@@ -25,22 +25,27 @@
 /*
  * skb_migrate appends the list at "from" to "to", emptying "from" in the
  * process. skb_migrate is atomic with respect to all other skb operations on
- * "from" and "to". Note that it locks both lists at the same time, so beware
- * of potential deadlocks.
+ * "from" and "to". Note that it locks both lists at the same time, so to deal
+ * with the lock ordering, the locks are taken in address order.
  *
  * This function should live in skbuff.c or skbuff.h.
  */
 
 
-void skb_migrate(struct sk_buff_head *from,struct sk_buff_head *to)
+void skb_migrate(struct sk_buff_head *from, struct sk_buff_head *to)
 {
 	unsigned long flags;
 	struct sk_buff *skb_from = (struct sk_buff *) from;
 	struct sk_buff *skb_to = (struct sk_buff *) to;
 	struct sk_buff *prev;
 
-	spin_lock_irqsave(&from->lock,flags);
-	spin_lock(&to->lock);
+	if ((unsigned long) from < (unsigned long) to) {
+		spin_lock_irqsave(&from->lock, flags);
+		spin_lock_nested(&to->lock, SINGLE_DEPTH_NESTING);
+	} else {
+		spin_lock_irqsave(&to->lock, flags);
+		spin_lock_nested(&from->lock, SINGLE_DEPTH_NESTING);
+	}
 	prev = from->prev;
 	from->next->prev = to->prev;
 	prev->next = skb_to;
@@ -51,7 +56,7 @@
 	from->prev = skb_from;
 	from->next = skb_from;
 	from->qlen = 0;
-	spin_unlock_irqrestore(&from->lock,flags);
+	spin_unlock_irqrestore(&from->lock, flags);
 }
 
 
diff --git a/net/ax25/af_ax25.c b/net/ax25/af_ax25.c
index 10a3c0a..f12be2a 100644
--- a/net/ax25/af_ax25.c
+++ b/net/ax25/af_ax25.c
@@ -486,10 +486,9 @@
 {
 	ax25_cb *ax25;
 
-	if ((ax25 = kmalloc(sizeof(*ax25), GFP_ATOMIC)) == NULL)
+	if ((ax25 = kzalloc(sizeof(*ax25), GFP_ATOMIC)) == NULL)
 		return NULL;
 
-	memset(ax25, 0x00, sizeof(*ax25));
 	atomic_set(&ax25->refcount, 1);
 
 	skb_queue_head_init(&ax25->write_queue);
diff --git a/net/ax25/ax25_dev.c b/net/ax25/ax25_dev.c
index 47e6e79..b7876782 100644
--- a/net/ax25/ax25_dev.c
+++ b/net/ax25/ax25_dev.c
@@ -55,15 +55,13 @@
 {
 	ax25_dev *ax25_dev;
 
-	if ((ax25_dev = kmalloc(sizeof(*ax25_dev), GFP_ATOMIC)) == NULL) {
+	if ((ax25_dev = kzalloc(sizeof(*ax25_dev), GFP_ATOMIC)) == NULL) {
 		printk(KERN_ERR "AX.25: ax25_dev_device_up - out of memory\n");
 		return;
 	}
 
 	ax25_unregister_sysctl();
 
-	memset(ax25_dev, 0x00, sizeof(*ax25_dev));
-
 	dev->ax25_ptr     = ax25_dev;
 	ax25_dev->dev     = dev;
 	dev_hold(dev);
diff --git a/net/bridge/br_forward.c b/net/bridge/br_forward.c
index 8be9f21..6ccd32b 100644
--- a/net/bridge/br_forward.c
+++ b/net/bridge/br_forward.c
@@ -35,7 +35,7 @@
 int br_dev_queue_push_xmit(struct sk_buff *skb)
 {
 	/* drop mtu oversized packets except gso */
-	if (packet_length(skb) > skb->dev->mtu && !skb_shinfo(skb)->gso_size)
+	if (packet_length(skb) > skb->dev->mtu && !skb_is_gso(skb))
 		kfree_skb(skb);
 	else {
 #ifdef CONFIG_BRIDGE_NETFILTER
diff --git a/net/bridge/br_netfilter.c b/net/bridge/br_netfilter.c
index 8298a51..cbc8a38 100644
--- a/net/bridge/br_netfilter.c
+++ b/net/bridge/br_netfilter.c
@@ -761,7 +761,7 @@
 {
 	if (skb->protocol == htons(ETH_P_IP) &&
 	    skb->len > skb->dev->mtu &&
-	    !skb_shinfo(skb)->gso_size)
+	    !skb_is_gso(skb))
 		return ip_fragment(skb, br_dev_queue_push_xmit);
 	else
 		return br_dev_queue_push_xmit(skb);
diff --git a/net/core/dev.c b/net/core/dev.c
index 066a60a..4d2b516 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -1162,9 +1162,17 @@
 	unsigned int csum;
 	int ret = 0, offset = skb->h.raw - skb->data;
 
-	if (inward) {
-		skb->ip_summed = CHECKSUM_NONE;
-		goto out;
+	if (inward)
+		goto out_set_summed;
+
+	if (unlikely(skb_shinfo(skb)->gso_size)) {
+		static int warned;
+
+		WARN_ON(!warned);
+		warned = 1;
+
+		/* Let GSO fix up the checksum. */
+		goto out_set_summed;
 	}
 
 	if (skb_cloned(skb)) {
@@ -1181,6 +1189,8 @@
 	BUG_ON(skb->csum + 2 > offset);
 
 	*(u16*)(skb->h.raw + skb->csum) = csum_fold(csum);
+
+out_set_summed:
 	skb->ip_summed = CHECKSUM_NONE;
 out:	
 	return ret;
@@ -1201,17 +1211,35 @@
 	struct sk_buff *segs = ERR_PTR(-EPROTONOSUPPORT);
 	struct packet_type *ptype;
 	int type = skb->protocol;
+	int err;
 
 	BUG_ON(skb_shinfo(skb)->frag_list);
-	BUG_ON(skb->ip_summed != CHECKSUM_HW);
 
 	skb->mac.raw = skb->data;
 	skb->mac_len = skb->nh.raw - skb->data;
 	__skb_pull(skb, skb->mac_len);
 
+	if (unlikely(skb->ip_summed != CHECKSUM_HW)) {
+		static int warned;
+
+		WARN_ON(!warned);
+		warned = 1;
+
+		if (skb_header_cloned(skb) &&
+		    (err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC)))
+			return ERR_PTR(err);
+	}
+
 	rcu_read_lock();
 	list_for_each_entry_rcu(ptype, &ptype_base[ntohs(type) & 15], list) {
 		if (ptype->type == type && !ptype->dev && ptype->gso_segment) {
+			if (unlikely(skb->ip_summed != CHECKSUM_HW)) {
+				err = ptype->gso_send_check(skb);
+				segs = ERR_PTR(err);
+				if (err || skb_gso_ok(skb, features))
+					break;
+				__skb_push(skb, skb->data - skb->nh.raw);
+			}
 			segs = ptype->gso_segment(skb, features);
 			break;
 		}
@@ -1727,7 +1755,7 @@
 	if (dev->qdisc_ingress) {
 		__u32 ttl = (__u32) G_TC_RTTL(skb->tc_verd);
 		if (MAX_RED_LOOP < ttl++) {
-			printk("Redir loop detected Dropping packet (%s->%s)\n",
+			printk(KERN_WARNING "Redir loop detected Dropping packet (%s->%s)\n",
 				skb->input_dev->name, skb->dev->name);
 			return TC_ACT_SHOT;
 		}
@@ -2922,7 +2950,7 @@
 	/* Fix illegal SG+CSUM combinations. */
 	if ((dev->features & NETIF_F_SG) &&
 	    !(dev->features & NETIF_F_ALL_CSUM)) {
-		printk("%s: Dropping NETIF_F_SG since no checksum feature.\n",
+		printk(KERN_NOTICE "%s: Dropping NETIF_F_SG since no checksum feature.\n",
 		       dev->name);
 		dev->features &= ~NETIF_F_SG;
 	}
@@ -2930,7 +2958,7 @@
 	/* TSO requires that SG is present as well. */
 	if ((dev->features & NETIF_F_TSO) &&
 	    !(dev->features & NETIF_F_SG)) {
-		printk("%s: Dropping NETIF_F_TSO since no SG feature.\n",
+		printk(KERN_NOTICE "%s: Dropping NETIF_F_TSO since no SG feature.\n",
 		       dev->name);
 		dev->features &= ~NETIF_F_TSO;
 	}
diff --git a/net/decnet/dn_rules.c b/net/decnet/dn_rules.c
index 06e785f..22f321d 100644
--- a/net/decnet/dn_rules.c
+++ b/net/decnet/dn_rules.c
@@ -399,9 +399,10 @@
 	rcu_read_lock();
 	hlist_for_each_entry(r, node, &dn_fib_rules, r_hlist) {
 		if (idx < s_idx)
-			continue;
+			goto next;
 		if (dn_fib_fill_rule(skb, r, cb, NLM_F_MULTI) < 0)
 			break;
+next:
 		idx++;
 	}
 	rcu_read_unlock();
diff --git a/net/ipv4/af_inet.c b/net/ipv4/af_inet.c
index 318d467..c84a320 100644
--- a/net/ipv4/af_inet.c
+++ b/net/ipv4/af_inet.c
@@ -1097,6 +1097,40 @@
 
 EXPORT_SYMBOL(inet_sk_rebuild_header);
 
+static int inet_gso_send_check(struct sk_buff *skb)
+{
+	struct iphdr *iph;
+	struct net_protocol *ops;
+	int proto;
+	int ihl;
+	int err = -EINVAL;
+
+	if (unlikely(!pskb_may_pull(skb, sizeof(*iph))))
+		goto out;
+
+	iph = skb->nh.iph;
+	ihl = iph->ihl * 4;
+	if (ihl < sizeof(*iph))
+		goto out;
+
+	if (unlikely(!pskb_may_pull(skb, ihl)))
+		goto out;
+
+	skb->h.raw = __skb_pull(skb, ihl);
+	iph = skb->nh.iph;
+	proto = iph->protocol & (MAX_INET_PROTOS - 1);
+	err = -EPROTONOSUPPORT;
+
+	rcu_read_lock();
+	ops = rcu_dereference(inet_protos[proto]);
+	if (likely(ops && ops->gso_send_check))
+		err = ops->gso_send_check(skb);
+	rcu_read_unlock();
+
+out:
+	return err;
+}
+
 static struct sk_buff *inet_gso_segment(struct sk_buff *skb, int features)
 {
 	struct sk_buff *segs = ERR_PTR(-EINVAL);
@@ -1162,6 +1196,7 @@
 static struct net_protocol tcp_protocol = {
 	.handler =	tcp_v4_rcv,
 	.err_handler =	tcp_v4_err,
+	.gso_send_check = tcp_v4_gso_send_check,
 	.gso_segment =	tcp_tso_segment,
 	.no_policy =	1,
 };
@@ -1208,6 +1243,7 @@
 static struct packet_type ip_packet_type = {
 	.type = __constant_htons(ETH_P_IP),
 	.func = ip_rcv,
+	.gso_send_check = inet_gso_send_check,
 	.gso_segment = inet_gso_segment,
 };
 
diff --git a/net/ipv4/fib_rules.c b/net/ipv4/fib_rules.c
index 6c642d1..773b12b 100644
--- a/net/ipv4/fib_rules.c
+++ b/net/ipv4/fib_rules.c
@@ -457,13 +457,13 @@
 
 	rcu_read_lock();
 	hlist_for_each_entry(r, node, &fib_rules, hlist) {
-
 		if (idx < s_idx)
-			continue;
+			goto next;
 		if (inet_fill_rule(skb, r, NETLINK_CB(cb->skb).pid,
 				   cb->nlh->nlmsg_seq,
 				   RTM_NEWRULE, NLM_F_MULTI) < 0)
 			break;
+next:
 		idx++;
 	}
 	rcu_read_unlock();
diff --git a/net/ipv4/ip_output.c b/net/ipv4/ip_output.c
index ca0e714..7c9f9a6 100644
--- a/net/ipv4/ip_output.c
+++ b/net/ipv4/ip_output.c
@@ -209,7 +209,7 @@
 		return dst_output(skb);
 	}
 #endif
-	if (skb->len > dst_mtu(skb->dst) && !skb_shinfo(skb)->gso_size)
+	if (skb->len > dst_mtu(skb->dst) && !skb_is_gso(skb))
 		return ip_fragment(skb, ip_finish_output2);
 	else
 		return ip_finish_output2(skb);
@@ -1095,7 +1095,7 @@
 	while (size > 0) {
 		int i;
 
-		if (skb_shinfo(skb)->gso_size)
+		if (skb_is_gso(skb))
 			len = size;
 		else {
 
diff --git a/net/ipv4/tcp_ipv4.c b/net/ipv4/tcp_ipv4.c
index 5a886e6..a891133 100644
--- a/net/ipv4/tcp_ipv4.c
+++ b/net/ipv4/tcp_ipv4.c
@@ -496,6 +496,24 @@
 	}
 }
 
+int tcp_v4_gso_send_check(struct sk_buff *skb)
+{
+	struct iphdr *iph;
+	struct tcphdr *th;
+
+	if (!pskb_may_pull(skb, sizeof(*th)))
+		return -EINVAL;
+
+	iph = skb->nh.iph;
+	th = skb->h.th;
+
+	th->check = 0;
+	th->check = ~tcp_v4_check(th, skb->len, iph->saddr, iph->daddr, 0);
+	skb->csum = offsetof(struct tcphdr, check);
+	skb->ip_summed = CHECKSUM_HW;
+	return 0;
+}
+
 /*
  *	This routine will send an RST to the other tcp.
  *
diff --git a/net/ipv4/xfrm4_output.c b/net/ipv4/xfrm4_output.c
index 193363e..d16f863 100644
--- a/net/ipv4/xfrm4_output.c
+++ b/net/ipv4/xfrm4_output.c
@@ -134,7 +134,7 @@
 	}
 #endif
 
-	if (!skb_shinfo(skb)->gso_size)
+	if (!skb_is_gso(skb))
 		return xfrm4_output_finish2(skb);
 
 	skb->protocol = htons(ETH_P_IP);
diff --git a/net/ipv6/ip6_output.c b/net/ipv6/ip6_output.c
index 2c5b445..3bc74ce 100644
--- a/net/ipv6/ip6_output.c
+++ b/net/ipv6/ip6_output.c
@@ -147,7 +147,7 @@
 
 int ip6_output(struct sk_buff *skb)
 {
-	if ((skb->len > dst_mtu(skb->dst) && !skb_shinfo(skb)->gso_size) ||
+	if ((skb->len > dst_mtu(skb->dst) && !skb_is_gso(skb)) ||
 				dst_allfrag(skb->dst))
 		return ip6_fragment(skb, ip6_output2);
 	else
@@ -229,7 +229,7 @@
 	skb->priority = sk->sk_priority;
 
 	mtu = dst_mtu(dst);
-	if ((skb->len <= mtu) || ipfragok || skb_shinfo(skb)->gso_size) {
+	if ((skb->len <= mtu) || ipfragok || skb_is_gso(skb)) {
 		IP6_INC_STATS(IPSTATS_MIB_OUTREQUESTS);
 		return NF_HOOK(PF_INET6, NF_IP6_LOCAL_OUT, skb, NULL, dst->dev,
 				dst_output);
diff --git a/net/ipv6/ipv6_sockglue.c b/net/ipv6/ipv6_sockglue.c
index 0c17dec..4332726 100644
--- a/net/ipv6/ipv6_sockglue.c
+++ b/net/ipv6/ipv6_sockglue.c
@@ -57,12 +57,71 @@
 
 DEFINE_SNMP_STAT(struct ipstats_mib, ipv6_statistics) __read_mostly;
 
+static struct inet6_protocol *ipv6_gso_pull_exthdrs(struct sk_buff *skb,
+						    int proto)
+{
+	struct inet6_protocol *ops = NULL;
+
+	for (;;) {
+		struct ipv6_opt_hdr *opth;
+		int len;
+
+		if (proto != NEXTHDR_HOP) {
+			ops = rcu_dereference(inet6_protos[proto]);
+
+			if (unlikely(!ops))
+				break;
+
+			if (!(ops->flags & INET6_PROTO_GSO_EXTHDR))
+				break;
+		}
+
+		if (unlikely(!pskb_may_pull(skb, 8)))
+			break;
+
+		opth = (void *)skb->data;
+		len = opth->hdrlen * 8 + 8;
+
+		if (unlikely(!pskb_may_pull(skb, len)))
+			break;
+
+		proto = opth->nexthdr;
+		__skb_pull(skb, len);
+	}
+
+	return ops;
+}
+
+static int ipv6_gso_send_check(struct sk_buff *skb)
+{
+	struct ipv6hdr *ipv6h;
+	struct inet6_protocol *ops;
+	int err = -EINVAL;
+
+	if (unlikely(!pskb_may_pull(skb, sizeof(*ipv6h))))
+		goto out;
+
+	ipv6h = skb->nh.ipv6h;
+	__skb_pull(skb, sizeof(*ipv6h));
+	err = -EPROTONOSUPPORT;
+
+	rcu_read_lock();
+	ops = ipv6_gso_pull_exthdrs(skb, ipv6h->nexthdr);
+	if (likely(ops && ops->gso_send_check)) {
+		skb->h.raw = skb->data;
+		err = ops->gso_send_check(skb);
+	}
+	rcu_read_unlock();
+
+out:
+	return err;
+}
+
 static struct sk_buff *ipv6_gso_segment(struct sk_buff *skb, int features)
 {
 	struct sk_buff *segs = ERR_PTR(-EINVAL);
 	struct ipv6hdr *ipv6h;
 	struct inet6_protocol *ops;
-	int proto;
 
 	if (unlikely(skb_shinfo(skb)->gso_type &
 		     ~(SKB_GSO_UDP |
@@ -76,42 +135,15 @@
 		goto out;
 
 	ipv6h = skb->nh.ipv6h;
-	proto = ipv6h->nexthdr;
 	__skb_pull(skb, sizeof(*ipv6h));
+	segs = ERR_PTR(-EPROTONOSUPPORT);
 
 	rcu_read_lock();
-	for (;;) {
-		struct ipv6_opt_hdr *opth;
-		int len;
-
-		if (proto != NEXTHDR_HOP) {
-			ops = rcu_dereference(inet6_protos[proto]);
-
-			if (unlikely(!ops))
-				goto unlock;
-
-			if (!(ops->flags & INET6_PROTO_GSO_EXTHDR))
-				break;
-		}
-
-		if (unlikely(!pskb_may_pull(skb, 8)))
-			goto unlock;
-
-		opth = (void *)skb->data;
-		len = opth->hdrlen * 8 + 8;
-
-		if (unlikely(!pskb_may_pull(skb, len)))
-			goto unlock;
-
-		proto = opth->nexthdr;
-		__skb_pull(skb, len);
-	}
-
-	skb->h.raw = skb->data;
-	if (likely(ops->gso_segment))
+	ops = ipv6_gso_pull_exthdrs(skb, ipv6h->nexthdr);
+	if (likely(ops && ops->gso_segment)) {
+		skb->h.raw = skb->data;
 		segs = ops->gso_segment(skb, features);
-
-unlock:
+	}
 	rcu_read_unlock();
 
 	if (unlikely(IS_ERR(segs)))
@@ -130,6 +162,7 @@
 static struct packet_type ipv6_packet_type = {
 	.type = __constant_htons(ETH_P_IPV6), 
 	.func = ipv6_rcv,
+	.gso_send_check = ipv6_gso_send_check,
 	.gso_segment = ipv6_gso_segment,
 };
 
diff --git a/net/ipv6/tcp_ipv6.c b/net/ipv6/tcp_ipv6.c
index 5bdcb90..923989d 100644
--- a/net/ipv6/tcp_ipv6.c
+++ b/net/ipv6/tcp_ipv6.c
@@ -552,6 +552,24 @@
 	}
 }
 
+static int tcp_v6_gso_send_check(struct sk_buff *skb)
+{
+	struct ipv6hdr *ipv6h;
+	struct tcphdr *th;
+
+	if (!pskb_may_pull(skb, sizeof(*th)))
+		return -EINVAL;
+
+	ipv6h = skb->nh.ipv6h;
+	th = skb->h.th;
+
+	th->check = 0;
+	th->check = ~csum_ipv6_magic(&ipv6h->saddr, &ipv6h->daddr, skb->len,
+				     IPPROTO_TCP, 0);
+	skb->csum = offsetof(struct tcphdr, check);
+	skb->ip_summed = CHECKSUM_HW;
+	return 0;
+}
 
 static void tcp_v6_send_reset(struct sk_buff *skb)
 {
@@ -1603,6 +1621,7 @@
 static struct inet6_protocol tcpv6_protocol = {
 	.handler	=	tcp_v6_rcv,
 	.err_handler	=	tcp_v6_err,
+	.gso_send_check	=	tcp_v6_gso_send_check,
 	.gso_segment	=	tcp_tso_segment,
 	.flags		=	INET6_PROTO_NOPOLICY|INET6_PROTO_FINAL,
 };
diff --git a/net/ipv6/xfrm6_output.c b/net/ipv6/xfrm6_output.c
index 48fccb1..0eea60e 100644
--- a/net/ipv6/xfrm6_output.c
+++ b/net/ipv6/xfrm6_output.c
@@ -122,7 +122,7 @@
 {
 	struct sk_buff *segs;
 
-	if (!skb_shinfo(skb)->gso_size)
+	if (!skb_is_gso(skb))
 		return xfrm6_output_finish2(skb);
 
 	skb->protocol = htons(ETH_P_IP);
diff --git a/net/netrom/af_netrom.c b/net/netrom/af_netrom.c
index 389a411..ecc7968 100644
--- a/net/netrom/af_netrom.c
+++ b/net/netrom/af_netrom.c
@@ -1382,14 +1382,12 @@
 		return -1;
 	}
 
-	dev_nr = kmalloc(nr_ndevs * sizeof(struct net_device *), GFP_KERNEL);
+	dev_nr = kzalloc(nr_ndevs * sizeof(struct net_device *), GFP_KERNEL);
 	if (dev_nr == NULL) {
 		printk(KERN_ERR "NET/ROM: nr_proto_init - unable to allocate device array\n");
 		return -1;
 	}
 
-	memset(dev_nr, 0x00, nr_ndevs * sizeof(struct net_device *));
-
 	for (i = 0; i < nr_ndevs; i++) {
 		char name[IFNAMSIZ];
 		struct net_device *dev;
diff --git a/net/rose/af_rose.c b/net/rose/af_rose.c
index d0a67bb..c115295 100644
--- a/net/rose/af_rose.c
+++ b/net/rose/af_rose.c
@@ -1490,14 +1490,13 @@
 
 	rose_callsign = null_ax25_address;
 
-	dev_rose = kmalloc(rose_ndevs * sizeof(struct net_device *), GFP_KERNEL);
+	dev_rose = kzalloc(rose_ndevs * sizeof(struct net_device *), GFP_KERNEL);
 	if (dev_rose == NULL) {
 		printk(KERN_ERR "ROSE: rose_proto_init - unable to allocate device structure\n");
 		rc = -ENOMEM;
 		goto out_proto_unregister;
 	}
 
-	memset(dev_rose, 0x00, rose_ndevs * sizeof(struct net_device*));
 	for (i = 0; i < rose_ndevs; i++) {
 		struct net_device *dev;
 		char name[IFNAMSIZ];
diff --git a/net/sched/act_api.c b/net/sched/act_api.c
index 599423c..0972247 100644
--- a/net/sched/act_api.c
+++ b/net/sched/act_api.c
@@ -602,8 +602,8 @@
 	return err;
 
 rtattr_failure:
-	module_put(a->ops->owner);
 nlmsg_failure:
+	module_put(a->ops->owner);
 err_out:
 	kfree_skb(skb);
 	kfree(a);