| |
| config AMIGA |
| bool |
| depends on APUS |
| default y |
| help |
| This option enables support for the Amiga series of computers. |
| |
| config ZORRO |
| bool |
| depends on APUS |
| default y |
| help |
| This enables support for the Zorro bus in the Amiga. If you have |
| expansion cards in your Amiga that conform to the Amiga |
| AutoConfig(tm) specification, say Y, otherwise N. Note that even |
| expansion cards that do not fit in the Zorro slots but fit in e.g. |
| the CPU slot may fall in this category, so you have to say Y to let |
| Linux use these. |
| |
| config ABSTRACT_CONSOLE |
| bool |
| depends on APUS |
| default y |
| |
| config APUS_FAST_EXCEPT |
| bool |
| depends on APUS |
| default y |
| |
| config AMIGA_PCMCIA |
| bool "Amiga 1200/600 PCMCIA support" |
| depends on APUS && EXPERIMENTAL |
| help |
| Include support in the kernel for pcmcia on Amiga 1200 and Amiga |
| 600. If you intend to use pcmcia cards say Y; otherwise say N. |
| |
| config AMIGA_BUILTIN_SERIAL |
| tristate "Amiga builtin serial support" |
| depends on APUS |
| help |
| If you want to use your Amiga's built-in serial port in Linux, |
| answer Y. |
| |
| To compile this driver as a module, choose M here. |
| |
| config GVPIOEXT |
| tristate "GVP IO-Extender support" |
| depends on APUS |
| help |
| If you want to use a GVP IO-Extender serial card in Linux, say Y. |
| Otherwise, say N. |
| |
| config GVPIOEXT_LP |
| tristate "GVP IO-Extender parallel printer support" |
| depends on GVPIOEXT |
| help |
| Say Y to enable driving a printer from the parallel port on your |
| GVP IO-Extender card, N otherwise. |
| |
| config GVPIOEXT_PLIP |
| tristate "GVP IO-Extender PLIP support" |
| depends on GVPIOEXT |
| help |
| Say Y to enable doing IP over the parallel port on your GVP |
| IO-Extender card, N otherwise. |
| |
| config MULTIFACE_III_TTY |
| tristate "Multiface Card III serial support" |
| depends on APUS |
| help |
| If you want to use a Multiface III card's serial port in Linux, |
| answer Y. |
| |
| To compile this driver as a module, choose M here. |
| |
| config A2232 |
| tristate "Commodore A2232 serial support (EXPERIMENTAL)" |
| depends on EXPERIMENTAL && APUS |
| ---help--- |
| This option supports the 2232 7-port serial card shipped with the |
| Amiga 2000 and other Zorro-bus machines, dating from 1989. At |
| a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip |
| each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The |
| ports were connected with 8 pin DIN connectors on the card bracket, |
| for which 8 pin to DB25 adapters were supplied. The card also had |
| jumpers internally to toggle various pinning configurations. |
| |
| This driver can be built as a module; but then "generic_serial" |
| will also be built as a module. This has to be loaded before |
| "ser_a2232". If you want to do this, answer M here. |
| |
| config WHIPPET_SERIAL |
| tristate "Hisoft Whippet PCMCIA serial support" |
| depends on AMIGA_PCMCIA |
| help |
| HiSoft has a web page at <http://www.hisoft.co.uk/>, but there |
| is no listing for the Whippet in their Amiga section. |
| |
| config APNE |
| tristate "PCMCIA NE2000 support" |
| depends on AMIGA_PCMCIA |
| help |
| If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, |
| say N. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called apne. |
| |
| config SERIAL_CONSOLE |
| bool "Support for serial port console" |
| depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y) |
| |
| config HEARTBEAT |
| bool "Use power LED as a heartbeat" |
| depends on APUS |
| help |
| Use the power-on LED on your machine as a load meter. The exact |
| behavior is platform-dependent, but normally the flash frequency is |
| a hyperbolic function of the 5-minute load average. |
| |
| config PROC_HARDWARE |
| bool "/proc/hardware support" |
| depends on APUS |
| |
| source "drivers/zorro/Kconfig" |
| |
| config PCI_PERMEDIA |
| bool "PCI for Permedia2" |
| depends on !4xx && !8xx && APUS |