Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/char/rocket_int.h b/drivers/char/rocket_int.h
new file mode 100644
index 0000000..8026872
--- /dev/null
+++ b/drivers/char/rocket_int.h
@@ -0,0 +1,1296 @@
+/*
+ * rocket_int.h --- internal header file for rocket.c
+ *
+ * Written by Theodore Ts'o, Copyright 1997.
+ * Copyright 1997 Comtrol Corporation.
+ *
+ */
+
+/*
+ * Definition of the types in rcktpt_type
+ */
+#define ROCKET_TYPE_NORMAL 0
+#define ROCKET_TYPE_MODEM 1
+#define ROCKET_TYPE_MODEMII 2
+#define ROCKET_TYPE_MODEMIII 3
+#define ROCKET_TYPE_PC104 4
+
+#include <asm/io.h>
+#include <asm/byteorder.h>
+
+typedef unsigned char Byte_t;
+typedef unsigned int ByteIO_t;
+
+typedef unsigned int Word_t;
+typedef unsigned int WordIO_t;
+
+typedef unsigned long DWord_t;
+typedef unsigned int DWordIO_t;
+
+/*
+ * Note! Normally the Linux I/O macros already take care of
+ * byte-swapping the I/O instructions. However, all accesses using
+ * sOutDW aren't really 32-bit accesses, but should be handled in byte
+ * order. Hence the use of the cpu_to_le32() macro to byte-swap
+ * things to no-op the byte swapping done by the big-endian outl()
+ * instruction.
+ */
+
+#ifdef ROCKET_DEBUG_IO
+static inline void sOutB(unsigned short port, unsigned char value)
+{
+#ifdef ROCKET_DEBUG_IO
+ printk("sOutB(%x, %x)...", port, value);
+#endif
+ outb_p(value, port);
+}
+
+static inline void sOutW(unsigned short port, unsigned short value)
+{
+#ifdef ROCKET_DEBUG_IO
+ printk("sOutW(%x, %x)...", port, value);
+#endif
+ outw_p(value, port);
+}
+
+static inline void sOutDW(unsigned short port, unsigned long value)
+{
+#ifdef ROCKET_DEBUG_IO
+ printk("sOutDW(%x, %lx)...", port, value);
+#endif
+ outl_p(cpu_to_le32(value), port);
+}
+
+static inline unsigned char sInB(unsigned short port)
+{
+ return inb_p(port);
+}
+
+static inline unsigned short sInW(unsigned short port)
+{
+ return inw_p(port);
+}
+
+#else /* !ROCKET_DEBUG_IO */
+#define sOutB(a, b) outb_p(b, a)
+#define sOutW(a, b) outw_p(b, a)
+#define sOutDW(port, value) outl_p(cpu_to_le32(value), port)
+#define sInB(a) (inb_p(a))
+#define sInW(a) (inw_p(a))
+#endif /* ROCKET_DEBUG_IO */
+
+/* This is used to move arrays of bytes so byte swapping isn't appropriate. */
+#define sOutStrW(port, addr, count) if (count) outsw(port, addr, count)
+#define sInStrW(port, addr, count) if (count) insw(port, addr, count)
+
+#define CTL_SIZE 8
+#define AIOP_CTL_SIZE 4
+#define CHAN_AIOP_SIZE 8
+#define MAX_PORTS_PER_AIOP 8
+#define MAX_AIOPS_PER_BOARD 4
+#define MAX_PORTS_PER_BOARD 32
+
+/* Bus type ID */
+#define isISA 0
+#define isPCI 1
+#define isMC 2
+
+/* Controller ID numbers */
+#define CTLID_NULL -1 /* no controller exists */
+#define CTLID_0001 0x0001 /* controller release 1 */
+
+/* AIOP ID numbers, identifies AIOP type implementing channel */
+#define AIOPID_NULL -1 /* no AIOP or channel exists */
+#define AIOPID_0001 0x0001 /* AIOP release 1 */
+
+#define NULLDEV -1 /* identifies non-existant device */
+#define NULLCTL -1 /* identifies non-existant controller */
+#define NULLCTLPTR (CONTROLLER_T *)0 /* identifies non-existant controller */
+#define NULLAIOP -1 /* identifies non-existant AIOP */
+#define NULLCHAN -1 /* identifies non-existant channel */
+
+/************************************************************************
+ Global Register Offsets - Direct Access - Fixed values
+************************************************************************/
+
+#define _CMD_REG 0x38 /* Command Register 8 Write */
+#define _INT_CHAN 0x39 /* Interrupt Channel Register 8 Read */
+#define _INT_MASK 0x3A /* Interrupt Mask Register 8 Read / Write */
+#define _UNUSED 0x3B /* Unused 8 */
+#define _INDX_ADDR 0x3C /* Index Register Address 16 Write */
+#define _INDX_DATA 0x3E /* Index Register Data 8/16 Read / Write */
+
+/************************************************************************
+ Channel Register Offsets for 1st channel in AIOP - Direct Access
+************************************************************************/
+#define _TD0 0x00 /* Transmit Data 16 Write */
+#define _RD0 0x00 /* Receive Data 16 Read */
+#define _CHN_STAT0 0x20 /* Channel Status 8/16 Read / Write */
+#define _FIFO_CNT0 0x10 /* Transmit/Receive FIFO Count 16 Read */
+#define _INT_ID0 0x30 /* Interrupt Identification 8 Read */
+
+/************************************************************************
+ Tx Control Register Offsets - Indexed - External - Fixed
+************************************************************************/
+#define _TX_ENBLS 0x980 /* Tx Processor Enables Register 8 Read / Write */
+#define _TXCMP1 0x988 /* Transmit Compare Value #1 8 Read / Write */
+#define _TXCMP2 0x989 /* Transmit Compare Value #2 8 Read / Write */
+#define _TXREP1B1 0x98A /* Tx Replace Value #1 - Byte 1 8 Read / Write */
+#define _TXREP1B2 0x98B /* Tx Replace Value #1 - Byte 2 8 Read / Write */
+#define _TXREP2 0x98C /* Transmit Replace Value #2 8 Read / Write */
+
+/************************************************************************
+Memory Controller Register Offsets - Indexed - External - Fixed
+************************************************************************/
+#define _RX_FIFO 0x000 /* Rx FIFO */
+#define _TX_FIFO 0x800 /* Tx FIFO */
+#define _RXF_OUTP 0x990 /* Rx FIFO OUT pointer 16 Read / Write */
+#define _RXF_INP 0x992 /* Rx FIFO IN pointer 16 Read / Write */
+#define _TXF_OUTP 0x994 /* Tx FIFO OUT pointer 8 Read / Write */
+#define _TXF_INP 0x995 /* Tx FIFO IN pointer 8 Read / Write */
+#define _TXP_CNT 0x996 /* Tx Priority Count 8 Read / Write */
+#define _TXP_PNTR 0x997 /* Tx Priority Pointer 8 Read / Write */
+
+#define PRI_PEND 0x80 /* Priority data pending (bit7, Tx pri cnt) */
+#define TXFIFO_SIZE 255 /* size of Tx FIFO */
+#define RXFIFO_SIZE 1023 /* size of Rx FIFO */
+
+/************************************************************************
+Tx Priority Buffer - Indexed - External - Fixed
+************************************************************************/
+#define _TXP_BUF 0x9C0 /* Tx Priority Buffer 32 Bytes Read / Write */
+#define TXP_SIZE 0x20 /* 32 bytes */
+
+/************************************************************************
+Channel Register Offsets - Indexed - Internal - Fixed
+************************************************************************/
+
+#define _TX_CTRL 0xFF0 /* Transmit Control 16 Write */
+#define _RX_CTRL 0xFF2 /* Receive Control 8 Write */
+#define _BAUD 0xFF4 /* Baud Rate 16 Write */
+#define _CLK_PRE 0xFF6 /* Clock Prescaler 8 Write */
+
+#define STMBREAK 0x08 /* BREAK */
+#define STMFRAME 0x04 /* framing error */
+#define STMRCVROVR 0x02 /* receiver over run error */
+#define STMPARITY 0x01 /* parity error */
+#define STMERROR (STMBREAK | STMFRAME | STMPARITY)
+#define STMBREAKH 0x800 /* BREAK */
+#define STMFRAMEH 0x400 /* framing error */
+#define STMRCVROVRH 0x200 /* receiver over run error */
+#define STMPARITYH 0x100 /* parity error */
+#define STMERRORH (STMBREAKH | STMFRAMEH | STMPARITYH)
+
+#define CTS_ACT 0x20 /* CTS input asserted */
+#define DSR_ACT 0x10 /* DSR input asserted */
+#define CD_ACT 0x08 /* CD input asserted */
+#define TXFIFOMT 0x04 /* Tx FIFO is empty */
+#define TXSHRMT 0x02 /* Tx shift register is empty */
+#define RDA 0x01 /* Rx data available */
+#define DRAINED (TXFIFOMT | TXSHRMT) /* indicates Tx is drained */
+
+#define STATMODE 0x8000 /* status mode enable bit */
+#define RXFOVERFL 0x2000 /* receive FIFO overflow */
+#define RX2MATCH 0x1000 /* receive compare byte 2 match */
+#define RX1MATCH 0x0800 /* receive compare byte 1 match */
+#define RXBREAK 0x0400 /* received BREAK */
+#define RXFRAME 0x0200 /* received framing error */
+#define RXPARITY 0x0100 /* received parity error */
+#define STATERROR (RXBREAK | RXFRAME | RXPARITY)
+
+#define CTSFC_EN 0x80 /* CTS flow control enable bit */
+#define RTSTOG_EN 0x40 /* RTS toggle enable bit */
+#define TXINT_EN 0x10 /* transmit interrupt enable */
+#define STOP2 0x08 /* enable 2 stop bits (0 = 1 stop) */
+#define PARITY_EN 0x04 /* enable parity (0 = no parity) */
+#define EVEN_PAR 0x02 /* even parity (0 = odd parity) */
+#define DATA8BIT 0x01 /* 8 bit data (0 = 7 bit data) */
+
+#define SETBREAK 0x10 /* send break condition (must clear) */
+#define LOCALLOOP 0x08 /* local loopback set for test */
+#define SET_DTR 0x04 /* assert DTR */
+#define SET_RTS 0x02 /* assert RTS */
+#define TX_ENABLE 0x01 /* enable transmitter */
+
+#define RTSFC_EN 0x40 /* RTS flow control enable */
+#define RXPROC_EN 0x20 /* receive processor enable */
+#define TRIG_NO 0x00 /* Rx FIFO trigger level 0 (no trigger) */
+#define TRIG_1 0x08 /* trigger level 1 char */
+#define TRIG_1_2 0x10 /* trigger level 1/2 */
+#define TRIG_7_8 0x18 /* trigger level 7/8 */
+#define TRIG_MASK 0x18 /* trigger level mask */
+#define SRCINT_EN 0x04 /* special Rx condition interrupt enable */
+#define RXINT_EN 0x02 /* Rx interrupt enable */
+#define MCINT_EN 0x01 /* modem change interrupt enable */
+
+#define RXF_TRIG 0x20 /* Rx FIFO trigger level interrupt */
+#define TXFIFO_MT 0x10 /* Tx FIFO empty interrupt */
+#define SRC_INT 0x08 /* special receive condition interrupt */
+#define DELTA_CD 0x04 /* CD change interrupt */
+#define DELTA_CTS 0x02 /* CTS change interrupt */
+#define DELTA_DSR 0x01 /* DSR change interrupt */
+
+#define REP1W2_EN 0x10 /* replace byte 1 with 2 bytes enable */
+#define IGN2_EN 0x08 /* ignore byte 2 enable */
+#define IGN1_EN 0x04 /* ignore byte 1 enable */
+#define COMP2_EN 0x02 /* compare byte 2 enable */
+#define COMP1_EN 0x01 /* compare byte 1 enable */
+
+#define RESET_ALL 0x80 /* reset AIOP (all channels) */
+#define TXOVERIDE 0x40 /* Transmit software off override */
+#define RESETUART 0x20 /* reset channel's UART */
+#define RESTXFCNT 0x10 /* reset channel's Tx FIFO count register */
+#define RESRXFCNT 0x08 /* reset channel's Rx FIFO count register */
+
+#define INTSTAT0 0x01 /* AIOP 0 interrupt status */
+#define INTSTAT1 0x02 /* AIOP 1 interrupt status */
+#define INTSTAT2 0x04 /* AIOP 2 interrupt status */
+#define INTSTAT3 0x08 /* AIOP 3 interrupt status */
+
+#define INTR_EN 0x08 /* allow interrupts to host */
+#define INT_STROB 0x04 /* strobe and clear interrupt line (EOI) */
+
+/**************************************************************************
+ MUDBAC remapped for PCI
+**************************************************************************/
+
+#define _CFG_INT_PCI 0x40
+#define _PCI_INT_FUNC 0x3A
+
+#define PCI_STROB 0x2000 /* bit 13 of int aiop register */
+#define INTR_EN_PCI 0x0010 /* allow interrupts to host */
+
+/*
+ * Definitions for Universal PCI board registers
+ */
+#define _PCI_9030_INT_CTRL 0x4c /* Offsets from BAR1 */
+#define _PCI_9030_GPIO_CTRL 0x54
+#define PCI_INT_CTRL_AIOP 0x0001
+#define PCI_GPIO_CTRL_8PORT 0x4000
+#define _PCI_9030_RING_IND 0xc0 /* Offsets from BAR1 */
+
+#define CHAN3_EN 0x08 /* enable AIOP 3 */
+#define CHAN2_EN 0x04 /* enable AIOP 2 */
+#define CHAN1_EN 0x02 /* enable AIOP 1 */
+#define CHAN0_EN 0x01 /* enable AIOP 0 */
+#define FREQ_DIS 0x00
+#define FREQ_274HZ 0x60
+#define FREQ_137HZ 0x50
+#define FREQ_69HZ 0x40
+#define FREQ_34HZ 0x30
+#define FREQ_17HZ 0x20
+#define FREQ_9HZ 0x10
+#define PERIODIC_ONLY 0x80 /* only PERIODIC interrupt */
+
+#define CHANINT_EN 0x0100 /* flags to enable/disable channel ints */
+
+#define RDATASIZE 72
+#define RREGDATASIZE 52
+
+/*
+ * AIOP interrupt bits for ISA/PCI boards and UPCI boards.
+ */
+#define AIOP_INTR_BIT_0 0x0001
+#define AIOP_INTR_BIT_1 0x0002
+#define AIOP_INTR_BIT_2 0x0004
+#define AIOP_INTR_BIT_3 0x0008
+
+#define AIOP_INTR_BITS ( \
+ AIOP_INTR_BIT_0 \
+ | AIOP_INTR_BIT_1 \
+ | AIOP_INTR_BIT_2 \
+ | AIOP_INTR_BIT_3)
+
+#define UPCI_AIOP_INTR_BIT_0 0x0004
+#define UPCI_AIOP_INTR_BIT_1 0x0020
+#define UPCI_AIOP_INTR_BIT_2 0x0100
+#define UPCI_AIOP_INTR_BIT_3 0x0800
+
+#define UPCI_AIOP_INTR_BITS ( \
+ UPCI_AIOP_INTR_BIT_0 \
+ | UPCI_AIOP_INTR_BIT_1 \
+ | UPCI_AIOP_INTR_BIT_2 \
+ | UPCI_AIOP_INTR_BIT_3)
+
+/* Controller level information structure */
+typedef struct {
+ int CtlID;
+ int CtlNum;
+ int BusType;
+ int boardType;
+ int isUPCI;
+ WordIO_t PCIIO;
+ WordIO_t PCIIO2;
+ ByteIO_t MBaseIO;
+ ByteIO_t MReg1IO;
+ ByteIO_t MReg2IO;
+ ByteIO_t MReg3IO;
+ Byte_t MReg2;
+ Byte_t MReg3;
+ int NumAiop;
+ int AltChanRingIndicator;
+ ByteIO_t UPCIRingInd;
+ WordIO_t AiopIO[AIOP_CTL_SIZE];
+ ByteIO_t AiopIntChanIO[AIOP_CTL_SIZE];
+ int AiopID[AIOP_CTL_SIZE];
+ int AiopNumChan[AIOP_CTL_SIZE];
+ Word_t *AiopIntrBits;
+} CONTROLLER_T;
+
+typedef CONTROLLER_T CONTROLLER_t;
+
+/* Channel level information structure */
+typedef struct {
+ CONTROLLER_T *CtlP;
+ int AiopNum;
+ int ChanID;
+ int ChanNum;
+ int rtsToggle;
+
+ ByteIO_t Cmd;
+ ByteIO_t IntChan;
+ ByteIO_t IntMask;
+ DWordIO_t IndexAddr;
+ WordIO_t IndexData;
+
+ WordIO_t TxRxData;
+ WordIO_t ChanStat;
+ WordIO_t TxRxCount;
+ ByteIO_t IntID;
+
+ Word_t TxFIFO;
+ Word_t TxFIFOPtrs;
+ Word_t RxFIFO;
+ Word_t RxFIFOPtrs;
+ Word_t TxPrioCnt;
+ Word_t TxPrioPtr;
+ Word_t TxPrioBuf;
+
+ Byte_t R[RREGDATASIZE];
+
+ Byte_t BaudDiv[4];
+ Byte_t TxControl[4];
+ Byte_t RxControl[4];
+ Byte_t TxEnables[4];
+ Byte_t TxCompare[4];
+ Byte_t TxReplace1[4];
+ Byte_t TxReplace2[4];
+} CHANNEL_T;
+
+typedef CHANNEL_T CHANNEL_t;
+typedef CHANNEL_T *CHANPTR_T;
+
+#define InterfaceModeRS232 0x00
+#define InterfaceModeRS422 0x08
+#define InterfaceModeRS485 0x10
+#define InterfaceModeRS232T 0x18
+
+/***************************************************************************
+Function: sClrBreak
+Purpose: Stop sending a transmit BREAK signal
+Call: sClrBreak(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sClrBreak(ChP) \
+do { \
+ (ChP)->TxControl[3] &= ~SETBREAK; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sClrDTR
+Purpose: Clr the DTR output
+Call: sClrDTR(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sClrDTR(ChP) \
+do { \
+ (ChP)->TxControl[3] &= ~SET_DTR; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sClrRTS
+Purpose: Clr the RTS output
+Call: sClrRTS(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sClrRTS(ChP) \
+do { \
+ if ((ChP)->rtsToggle) break; \
+ (ChP)->TxControl[3] &= ~SET_RTS; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sClrTxXOFF
+Purpose: Clear any existing transmit software flow control off condition
+Call: sClrTxXOFF(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sClrTxXOFF(ChP) \
+do { \
+ sOutB((ChP)->Cmd,TXOVERIDE | (Byte_t)(ChP)->ChanNum); \
+ sOutB((ChP)->Cmd,(Byte_t)(ChP)->ChanNum); \
+} while (0)
+
+/***************************************************************************
+Function: sCtlNumToCtlPtr
+Purpose: Convert a controller number to controller structure pointer
+Call: sCtlNumToCtlPtr(CtlNum)
+ int CtlNum; Controller number
+Return: CONTROLLER_T *: Ptr to controller structure
+*/
+#define sCtlNumToCtlPtr(CTLNUM) &sController[CTLNUM]
+
+/***************************************************************************
+Function: sControllerEOI
+Purpose: Strobe the MUDBAC's End Of Interrupt bit.
+Call: sControllerEOI(CtlP)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+*/
+#define sControllerEOI(CTLP) sOutB((CTLP)->MReg2IO,(CTLP)->MReg2 | INT_STROB)
+
+/***************************************************************************
+Function: sPCIControllerEOI
+Purpose: Strobe the PCI End Of Interrupt bit.
+ For the UPCI boards, toggle the AIOP interrupt enable bit
+ (this was taken from the Windows driver).
+Call: sPCIControllerEOI(CtlP)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+*/
+#define sPCIControllerEOI(CTLP) \
+do { \
+ if ((CTLP)->isUPCI) { \
+ Word_t w = sInW((CTLP)->PCIIO); \
+ sOutW((CTLP)->PCIIO, (w ^ PCI_INT_CTRL_AIOP)); \
+ sOutW((CTLP)->PCIIO, w); \
+ } \
+ else { \
+ sOutW((CTLP)->PCIIO, PCI_STROB); \
+ } \
+} while (0)
+
+/***************************************************************************
+Function: sDisAiop
+Purpose: Disable I/O access to an AIOP
+Call: sDisAiop(CltP)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int AiopNum; Number of AIOP on controller
+*/
+#define sDisAiop(CTLP,AIOPNUM) \
+do { \
+ (CTLP)->MReg3 &= sBitMapClrTbl[AIOPNUM]; \
+ sOutB((CTLP)->MReg3IO,(CTLP)->MReg3); \
+} while (0)
+
+/***************************************************************************
+Function: sDisCTSFlowCtl
+Purpose: Disable output flow control using CTS
+Call: sDisCTSFlowCtl(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sDisCTSFlowCtl(ChP) \
+do { \
+ (ChP)->TxControl[2] &= ~CTSFC_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sDisIXANY
+Purpose: Disable IXANY Software Flow Control
+Call: sDisIXANY(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sDisIXANY(ChP) \
+do { \
+ (ChP)->R[0x0e] = 0x86; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x0c]); \
+} while (0)
+
+/***************************************************************************
+Function: DisParity
+Purpose: Disable parity
+Call: sDisParity(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: Function sSetParity() can be used in place of functions sEnParity(),
+ sDisParity(), sSetOddParity(), and sSetEvenParity().
+*/
+#define sDisParity(ChP) \
+do { \
+ (ChP)->TxControl[2] &= ~PARITY_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sDisRTSToggle
+Purpose: Disable RTS toggle
+Call: sDisRTSToggle(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sDisRTSToggle(ChP) \
+do { \
+ (ChP)->TxControl[2] &= ~RTSTOG_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+ (ChP)->rtsToggle = 0; \
+} while (0)
+
+/***************************************************************************
+Function: sDisRxFIFO
+Purpose: Disable Rx FIFO
+Call: sDisRxFIFO(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sDisRxFIFO(ChP) \
+do { \
+ (ChP)->R[0x32] = 0x0a; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x30]); \
+} while (0)
+
+/***************************************************************************
+Function: sDisRxStatusMode
+Purpose: Disable the Rx status mode
+Call: sDisRxStatusMode(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: This takes the channel out of the receive status mode. All
+ subsequent reads of receive data using sReadRxWord() will return
+ two data bytes.
+*/
+#define sDisRxStatusMode(ChP) sOutW((ChP)->ChanStat,0)
+
+/***************************************************************************
+Function: sDisTransmit
+Purpose: Disable transmit
+Call: sDisTransmit(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+ This disables movement of Tx data from the Tx FIFO into the 1 byte
+ Tx buffer. Therefore there could be up to a 2 byte latency
+ between the time sDisTransmit() is called and the transmit buffer
+ and transmit shift register going completely empty.
+*/
+#define sDisTransmit(ChP) \
+do { \
+ (ChP)->TxControl[3] &= ~TX_ENABLE; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sDisTxSoftFlowCtl
+Purpose: Disable Tx Software Flow Control
+Call: sDisTxSoftFlowCtl(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sDisTxSoftFlowCtl(ChP) \
+do { \
+ (ChP)->R[0x06] = 0x8a; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x04]); \
+} while (0)
+
+/***************************************************************************
+Function: sEnAiop
+Purpose: Enable I/O access to an AIOP
+Call: sEnAiop(CltP)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int AiopNum; Number of AIOP on controller
+*/
+#define sEnAiop(CTLP,AIOPNUM) \
+do { \
+ (CTLP)->MReg3 |= sBitMapSetTbl[AIOPNUM]; \
+ sOutB((CTLP)->MReg3IO,(CTLP)->MReg3); \
+} while (0)
+
+/***************************************************************************
+Function: sEnCTSFlowCtl
+Purpose: Enable output flow control using CTS
+Call: sEnCTSFlowCtl(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sEnCTSFlowCtl(ChP) \
+do { \
+ (ChP)->TxControl[2] |= CTSFC_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sEnIXANY
+Purpose: Enable IXANY Software Flow Control
+Call: sEnIXANY(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sEnIXANY(ChP) \
+do { \
+ (ChP)->R[0x0e] = 0x21; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x0c]); \
+} while (0)
+
+/***************************************************************************
+Function: EnParity
+Purpose: Enable parity
+Call: sEnParity(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: Function sSetParity() can be used in place of functions sEnParity(),
+ sDisParity(), sSetOddParity(), and sSetEvenParity().
+
+Warnings: Before enabling parity odd or even parity should be chosen using
+ functions sSetOddParity() or sSetEvenParity().
+*/
+#define sEnParity(ChP) \
+do { \
+ (ChP)->TxControl[2] |= PARITY_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sEnRTSToggle
+Purpose: Enable RTS toggle
+Call: sEnRTSToggle(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: This function will disable RTS flow control and clear the RTS
+ line to allow operation of RTS toggle.
+*/
+#define sEnRTSToggle(ChP) \
+do { \
+ (ChP)->RxControl[2] &= ~RTSFC_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->RxControl[0]); \
+ (ChP)->TxControl[2] |= RTSTOG_EN; \
+ (ChP)->TxControl[3] &= ~SET_RTS; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+ (ChP)->rtsToggle = 1; \
+} while (0)
+
+/***************************************************************************
+Function: sEnRxFIFO
+Purpose: Enable Rx FIFO
+Call: sEnRxFIFO(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sEnRxFIFO(ChP) \
+do { \
+ (ChP)->R[0x32] = 0x08; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x30]); \
+} while (0)
+
+/***************************************************************************
+Function: sEnRxProcessor
+Purpose: Enable the receive processor
+Call: sEnRxProcessor(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: This function is used to start the receive processor. When
+ the channel is in the reset state the receive processor is not
+ running. This is done to prevent the receive processor from
+ executing invalid microcode instructions prior to the
+ downloading of the microcode.
+
+Warnings: This function must be called after valid microcode has been
+ downloaded to the AIOP, and it must not be called before the
+ microcode has been downloaded.
+*/
+#define sEnRxProcessor(ChP) \
+do { \
+ (ChP)->RxControl[2] |= RXPROC_EN; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->RxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sEnRxStatusMode
+Purpose: Enable the Rx status mode
+Call: sEnRxStatusMode(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: This places the channel in the receive status mode. All subsequent
+ reads of receive data using sReadRxWord() will return a data byte
+ in the low word and a status byte in the high word.
+
+*/
+#define sEnRxStatusMode(ChP) sOutW((ChP)->ChanStat,STATMODE)
+
+/***************************************************************************
+Function: sEnTransmit
+Purpose: Enable transmit
+Call: sEnTransmit(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sEnTransmit(ChP) \
+do { \
+ (ChP)->TxControl[3] |= TX_ENABLE; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sEnTxSoftFlowCtl
+Purpose: Enable Tx Software Flow Control
+Call: sEnTxSoftFlowCtl(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sEnTxSoftFlowCtl(ChP) \
+do { \
+ (ChP)->R[0x06] = 0xc5; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x04]); \
+} while (0)
+
+/***************************************************************************
+Function: sGetAiopIntStatus
+Purpose: Get the AIOP interrupt status
+Call: sGetAiopIntStatus(CtlP,AiopNum)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int AiopNum; AIOP number
+Return: Byte_t: The AIOP interrupt status. Bits 0 through 7
+ represent channels 0 through 7 respectively. If a
+ bit is set that channel is interrupting.
+*/
+#define sGetAiopIntStatus(CTLP,AIOPNUM) sInB((CTLP)->AiopIntChanIO[AIOPNUM])
+
+/***************************************************************************
+Function: sGetAiopNumChan
+Purpose: Get the number of channels supported by an AIOP
+Call: sGetAiopNumChan(CtlP,AiopNum)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int AiopNum; AIOP number
+Return: int: The number of channels supported by the AIOP
+*/
+#define sGetAiopNumChan(CTLP,AIOPNUM) (CTLP)->AiopNumChan[AIOPNUM]
+
+/***************************************************************************
+Function: sGetChanIntID
+Purpose: Get a channel's interrupt identification byte
+Call: sGetChanIntID(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: Byte_t: The channel interrupt ID. Can be any
+ combination of the following flags:
+ RXF_TRIG: Rx FIFO trigger level interrupt
+ TXFIFO_MT: Tx FIFO empty interrupt
+ SRC_INT: Special receive condition interrupt
+ DELTA_CD: CD change interrupt
+ DELTA_CTS: CTS change interrupt
+ DELTA_DSR: DSR change interrupt
+*/
+#define sGetChanIntID(ChP) (sInB((ChP)->IntID) & (RXF_TRIG | TXFIFO_MT | SRC_INT | DELTA_CD | DELTA_CTS | DELTA_DSR))
+
+/***************************************************************************
+Function: sGetChanNum
+Purpose: Get the number of a channel within an AIOP
+Call: sGetChanNum(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: int: Channel number within AIOP, or NULLCHAN if channel does
+ not exist.
+*/
+#define sGetChanNum(ChP) (ChP)->ChanNum
+
+/***************************************************************************
+Function: sGetChanStatus
+Purpose: Get the channel status
+Call: sGetChanStatus(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: Word_t: The channel status. Can be any combination of
+ the following flags:
+ LOW BYTE FLAGS
+ CTS_ACT: CTS input asserted
+ DSR_ACT: DSR input asserted
+ CD_ACT: CD input asserted
+ TXFIFOMT: Tx FIFO is empty
+ TXSHRMT: Tx shift register is empty
+ RDA: Rx data available
+
+ HIGH BYTE FLAGS
+ STATMODE: status mode enable bit
+ RXFOVERFL: receive FIFO overflow
+ RX2MATCH: receive compare byte 2 match
+ RX1MATCH: receive compare byte 1 match
+ RXBREAK: received BREAK
+ RXFRAME: received framing error
+ RXPARITY: received parity error
+Warnings: This function will clear the high byte flags in the Channel
+ Status Register.
+*/
+#define sGetChanStatus(ChP) sInW((ChP)->ChanStat)
+
+/***************************************************************************
+Function: sGetChanStatusLo
+Purpose: Get the low byte only of the channel status
+Call: sGetChanStatusLo(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: Byte_t: The channel status low byte. Can be any combination
+ of the following flags:
+ CTS_ACT: CTS input asserted
+ DSR_ACT: DSR input asserted
+ CD_ACT: CD input asserted
+ TXFIFOMT: Tx FIFO is empty
+ TXSHRMT: Tx shift register is empty
+ RDA: Rx data available
+*/
+#define sGetChanStatusLo(ChP) sInB((ByteIO_t)(ChP)->ChanStat)
+
+/**********************************************************************
+ * Get RI status of channel
+ * Defined as a function in rocket.c -aes
+ */
+#if 0
+#define sGetChanRI(ChP) ((ChP)->CtlP->AltChanRingIndicator ? \
+ (sInB((ByteIO_t)((ChP)->ChanStat+8)) & DSR_ACT) : \
+ (((ChP)->CtlP->boardType == ROCKET_TYPE_PC104) ? \
+ (!(sInB((ChP)->CtlP->AiopIO[3]) & sBitMapSetTbl[(ChP)->ChanNum])) : \
+ 0))
+#endif
+
+/***************************************************************************
+Function: sGetControllerIntStatus
+Purpose: Get the controller interrupt status
+Call: sGetControllerIntStatus(CtlP)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+Return: Byte_t: The controller interrupt status in the lower 4
+ bits. Bits 0 through 3 represent AIOP's 0
+ through 3 respectively. If a bit is set that
+ AIOP is interrupting. Bits 4 through 7 will
+ always be cleared.
+*/
+#define sGetControllerIntStatus(CTLP) (sInB((CTLP)->MReg1IO) & 0x0f)
+
+/***************************************************************************
+Function: sPCIGetControllerIntStatus
+Purpose: Get the controller interrupt status
+Call: sPCIGetControllerIntStatus(CtlP)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+Return: unsigned char: The controller interrupt status in the lower 4
+ bits and bit 4. Bits 0 through 3 represent AIOP's 0
+ through 3 respectively. Bit 4 is set if the int
+ was generated from periodic. If a bit is set the
+ AIOP is interrupting.
+*/
+#define sPCIGetControllerIntStatus(CTLP) \
+ ((CTLP)->isUPCI ? \
+ (sInW((CTLP)->PCIIO2) & UPCI_AIOP_INTR_BITS) : \
+ ((sInW((CTLP)->PCIIO) >> 8) & AIOP_INTR_BITS))
+
+/***************************************************************************
+
+Function: sGetRxCnt
+Purpose: Get the number of data bytes in the Rx FIFO
+Call: sGetRxCnt(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: int: The number of data bytes in the Rx FIFO.
+Comments: Byte read of count register is required to obtain Rx count.
+
+*/
+#define sGetRxCnt(ChP) sInW((ChP)->TxRxCount)
+
+/***************************************************************************
+Function: sGetTxCnt
+Purpose: Get the number of data bytes in the Tx FIFO
+Call: sGetTxCnt(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: Byte_t: The number of data bytes in the Tx FIFO.
+Comments: Byte read of count register is required to obtain Tx count.
+
+*/
+#define sGetTxCnt(ChP) sInB((ByteIO_t)(ChP)->TxRxCount)
+
+/*****************************************************************************
+Function: sGetTxRxDataIO
+Purpose: Get the I/O address of a channel's TxRx Data register
+Call: sGetTxRxDataIO(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Return: WordIO_t: I/O address of a channel's TxRx Data register
+*/
+#define sGetTxRxDataIO(ChP) (ChP)->TxRxData
+
+/***************************************************************************
+Function: sInitChanDefaults
+Purpose: Initialize a channel structure to it's default state.
+Call: sInitChanDefaults(ChP)
+ CHANNEL_T *ChP; Ptr to the channel structure
+Comments: This function must be called once for every channel structure
+ that exists before any other SSCI calls can be made.
+
+*/
+#define sInitChanDefaults(ChP) \
+do { \
+ (ChP)->CtlP = NULLCTLPTR; \
+ (ChP)->AiopNum = NULLAIOP; \
+ (ChP)->ChanID = AIOPID_NULL; \
+ (ChP)->ChanNum = NULLCHAN; \
+} while (0)
+
+/***************************************************************************
+Function: sResetAiopByNum
+Purpose: Reset the AIOP by number
+Call: sResetAiopByNum(CTLP,AIOPNUM)
+ CONTROLLER_T CTLP; Ptr to controller structure
+ AIOPNUM; AIOP index
+*/
+#define sResetAiopByNum(CTLP,AIOPNUM) \
+do { \
+ sOutB((CTLP)->AiopIO[(AIOPNUM)]+_CMD_REG,RESET_ALL); \
+ sOutB((CTLP)->AiopIO[(AIOPNUM)]+_CMD_REG,0x0); \
+} while (0)
+
+/***************************************************************************
+Function: sSendBreak
+Purpose: Send a transmit BREAK signal
+Call: sSendBreak(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSendBreak(ChP) \
+do { \
+ (ChP)->TxControl[3] |= SETBREAK; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetBaud
+Purpose: Set baud rate
+Call: sSetBaud(ChP,Divisor)
+ CHANNEL_T *ChP; Ptr to channel structure
+ Word_t Divisor; 16 bit baud rate divisor for channel
+*/
+#define sSetBaud(ChP,DIVISOR) \
+do { \
+ (ChP)->BaudDiv[2] = (Byte_t)(DIVISOR); \
+ (ChP)->BaudDiv[3] = (Byte_t)((DIVISOR) >> 8); \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->BaudDiv[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetData7
+Purpose: Set data bits to 7
+Call: sSetData7(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSetData7(ChP) \
+do { \
+ (ChP)->TxControl[2] &= ~DATA8BIT; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetData8
+Purpose: Set data bits to 8
+Call: sSetData8(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSetData8(ChP) \
+do { \
+ (ChP)->TxControl[2] |= DATA8BIT; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetDTR
+Purpose: Set the DTR output
+Call: sSetDTR(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSetDTR(ChP) \
+do { \
+ (ChP)->TxControl[3] |= SET_DTR; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetEvenParity
+Purpose: Set even parity
+Call: sSetEvenParity(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: Function sSetParity() can be used in place of functions sEnParity(),
+ sDisParity(), sSetOddParity(), and sSetEvenParity().
+
+Warnings: This function has no effect unless parity is enabled with function
+ sEnParity().
+*/
+#define sSetEvenParity(ChP) \
+do { \
+ (ChP)->TxControl[2] |= EVEN_PAR; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetOddParity
+Purpose: Set odd parity
+Call: sSetOddParity(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: Function sSetParity() can be used in place of functions sEnParity(),
+ sDisParity(), sSetOddParity(), and sSetEvenParity().
+
+Warnings: This function has no effect unless parity is enabled with function
+ sEnParity().
+*/
+#define sSetOddParity(ChP) \
+do { \
+ (ChP)->TxControl[2] &= ~EVEN_PAR; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetRTS
+Purpose: Set the RTS output
+Call: sSetRTS(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSetRTS(ChP) \
+do { \
+ if ((ChP)->rtsToggle) break; \
+ (ChP)->TxControl[3] |= SET_RTS; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetRxTrigger
+Purpose: Set the Rx FIFO trigger level
+Call: sSetRxProcessor(ChP,Level)
+ CHANNEL_T *ChP; Ptr to channel structure
+ Byte_t Level; Number of characters in Rx FIFO at which the
+ interrupt will be generated. Can be any of the following flags:
+
+ TRIG_NO: no trigger
+ TRIG_1: 1 character in FIFO
+ TRIG_1_2: FIFO 1/2 full
+ TRIG_7_8: FIFO 7/8 full
+Comments: An interrupt will be generated when the trigger level is reached
+ only if function sEnInterrupt() has been called with flag
+ RXINT_EN set. The RXF_TRIG flag in the Interrupt Idenfification
+ register will be set whenever the trigger level is reached
+ regardless of the setting of RXINT_EN.
+
+*/
+#define sSetRxTrigger(ChP,LEVEL) \
+do { \
+ (ChP)->RxControl[2] &= ~TRIG_MASK; \
+ (ChP)->RxControl[2] |= LEVEL; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->RxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetStop1
+Purpose: Set stop bits to 1
+Call: sSetStop1(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSetStop1(ChP) \
+do { \
+ (ChP)->TxControl[2] &= ~STOP2; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetStop2
+Purpose: Set stop bits to 2
+Call: sSetStop2(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+*/
+#define sSetStop2(ChP) \
+do { \
+ (ChP)->TxControl[2] |= STOP2; \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->TxControl[0]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetTxXOFFChar
+Purpose: Set the Tx XOFF flow control character
+Call: sSetTxXOFFChar(ChP,Ch)
+ CHANNEL_T *ChP; Ptr to channel structure
+ Byte_t Ch; The value to set the Tx XOFF character to
+*/
+#define sSetTxXOFFChar(ChP,CH) \
+do { \
+ (ChP)->R[0x07] = (CH); \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x04]); \
+} while (0)
+
+/***************************************************************************
+Function: sSetTxXONChar
+Purpose: Set the Tx XON flow control character
+Call: sSetTxXONChar(ChP,Ch)
+ CHANNEL_T *ChP; Ptr to channel structure
+ Byte_t Ch; The value to set the Tx XON character to
+*/
+#define sSetTxXONChar(ChP,CH) \
+do { \
+ (ChP)->R[0x0b] = (CH); \
+ sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0x08]); \
+} while (0)
+
+/***************************************************************************
+Function: sStartRxProcessor
+Purpose: Start a channel's receive processor
+Call: sStartRxProcessor(ChP)
+ CHANNEL_T *ChP; Ptr to channel structure
+Comments: This function is used to start a Rx processor after it was
+ stopped with sStopRxProcessor() or sStopSWInFlowCtl(). It
+ will restart both the Rx processor and software input flow control.
+
+*/
+#define sStartRxProcessor(ChP) sOutDW((ChP)->IndexAddr,*(DWord_t *)&(ChP)->R[0])
+
+/***************************************************************************
+Function: sWriteTxByte
+Purpose: Write a transmit data byte to a channel.
+ ByteIO_t io: Channel transmit register I/O address. This can
+ be obtained with sGetTxRxDataIO().
+ Byte_t Data; The transmit data byte.
+Warnings: This function writes the data byte without checking to see if
+ sMaxTxSize is exceeded in the Tx FIFO.
+*/
+#define sWriteTxByte(IO,DATA) sOutB(IO,DATA)
+
+int sInitController(CONTROLLER_T * CtlP,
+ int CtlNum,
+ ByteIO_t MudbacIO,
+ ByteIO_t * AiopIOList,
+ int AiopIOListSize,
+ int IRQNum, Byte_t Frequency, int PeriodicOnly);
+
+int sPCIInitController(CONTROLLER_T * CtlP,
+ int CtlNum,
+ ByteIO_t * AiopIOList,
+ int AiopIOListSize,
+ WordIO_t ConfigIO,
+ int IRQNum,
+ Byte_t Frequency,
+ int PeriodicOnly,
+ int altChanRingIndicator, int UPCIRingInd);
+
+int sReadAiopID(ByteIO_t io);
+int sReadAiopNumChan(WordIO_t io);
+int sInitChan(CONTROLLER_T * CtlP,
+ CHANNEL_T * ChP, int AiopNum, int ChanNum);
+Byte_t sGetRxErrStatus(CHANNEL_T * ChP);
+void sStopRxProcessor(CHANNEL_T * ChP);
+void sStopSWInFlowCtl(CHANNEL_T * ChP);
+void sFlushRxFIFO(CHANNEL_T * ChP);
+void sFlushTxFIFO(CHANNEL_T * ChP);
+int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data);
+void sEnInterrupts(CHANNEL_T * ChP, Word_t Flags);
+void sDisInterrupts(CHANNEL_T * ChP, Word_t Flags);
+void sModemReset(CONTROLLER_T * CtlP, int chan, int on);
+void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on);
+void sSetInterfaceMode(CHANNEL_T * ChP, Byte_t mode);
+
+extern Byte_t R[RDATASIZE];
+extern CONTROLLER_T sController[CTL_SIZE];
+extern Byte_t sIRQMap[16];
+extern Byte_t sBitMapClrTbl[8];
+extern Byte_t sBitMapSetTbl[8];
+extern int sClockPrescale;
+
+/*
+ * Begin Linux specific definitions for the Rocketport driver
+ *
+ * This code is Copyright Theodore Ts'o, 1995-1997
+ */
+
+struct r_port {
+ int magic;
+ int line;
+ int flags;
+ int count;
+ int blocked_open;
+ struct tty_struct *tty;
+ unsigned int board:3;
+ unsigned int aiop:2;
+ unsigned int chan:3;
+ CONTROLLER_t *ctlp;
+ CHANNEL_t channel;
+ int closing_wait;
+ int close_delay;
+ int intmask;
+ int xmit_fifo_room; /* room in xmit fifo */
+ unsigned char *xmit_buf;
+ int xmit_head;
+ int xmit_tail;
+ int xmit_cnt;
+ int session;
+ int pgrp;
+ int cd_status;
+ int ignore_status_mask;
+ int read_status_mask;
+ int cps;
+
+#ifdef DECLARE_WAITQUEUE
+ wait_queue_head_t open_wait;
+ wait_queue_head_t close_wait;
+#else
+ struct wait_queue *open_wait;
+ struct wait_queue *close_wait;
+#endif
+ spinlock_t slock;
+ struct semaphore write_sem;
+};
+
+#define RPORT_MAGIC 0x525001
+
+#define NUM_BOARDS 8
+#define MAX_RP_PORTS (32*NUM_BOARDS)
+
+/*
+ * The size of the xmit buffer is 1 page, or 4096 bytes
+ */
+#define XMIT_BUF_SIZE 4096
+
+/* number of characters left in xmit buffer before we ask for more */
+#define WAKEUP_CHARS 256
+
+/* Internal flags used only by the rocketport driver */
+#define ROCKET_INITIALIZED 0x80000000 /* Port is active */
+#define ROCKET_CLOSING 0x40000000 /* Serial port is closing */
+#define ROCKET_NORMAL_ACTIVE 0x20000000 /* Normal port is active */
+
+/* tty subtypes */
+#define SERIAL_TYPE_NORMAL 1
+
+/*
+ * Assigned major numbers for the Comtrol Rocketport
+ */
+#define TTY_ROCKET_MAJOR 46
+#define CUA_ROCKET_MAJOR 47
+
+#ifdef PCI_VENDOR_ID_RP
+#undef PCI_VENDOR_ID_RP
+#undef PCI_DEVICE_ID_RP8OCTA
+#undef PCI_DEVICE_ID_RP8INTF
+#undef PCI_DEVICE_ID_RP16INTF
+#undef PCI_DEVICE_ID_RP32INTF
+#undef PCI_DEVICE_ID_URP8OCTA
+#undef PCI_DEVICE_ID_URP8INTF
+#undef PCI_DEVICE_ID_URP16INTF
+#undef PCI_DEVICE_ID_CRP16INTF
+#undef PCI_DEVICE_ID_URP32INTF
+#endif
+
+/* Comtrol PCI Vendor ID */
+#define PCI_VENDOR_ID_RP 0x11fe
+
+/* Comtrol Device ID's */
+#define PCI_DEVICE_ID_RP32INTF 0x0001 /* Rocketport 32 port w/external I/F */
+#define PCI_DEVICE_ID_RP8INTF 0x0002 /* Rocketport 8 port w/external I/F */
+#define PCI_DEVICE_ID_RP16INTF 0x0003 /* Rocketport 16 port w/external I/F */
+#define PCI_DEVICE_ID_RP4QUAD 0x0004 /* Rocketport 4 port w/quad cable */
+#define PCI_DEVICE_ID_RP8OCTA 0x0005 /* Rocketport 8 port w/octa cable */
+#define PCI_DEVICE_ID_RP8J 0x0006 /* Rocketport 8 port w/RJ11 connectors */
+#define PCI_DEVICE_ID_RP4J 0x0007 /* Rocketport 4 port w/RJ11 connectors */
+#define PCI_DEVICE_ID_RP8SNI 0x0008 /* Rocketport 8 port w/ DB78 SNI (Siemens) connector */
+#define PCI_DEVICE_ID_RP16SNI 0x0009 /* Rocketport 16 port w/ DB78 SNI (Siemens) connector */
+#define PCI_DEVICE_ID_RPP4 0x000A /* Rocketport Plus 4 port */
+#define PCI_DEVICE_ID_RPP8 0x000B /* Rocketport Plus 8 port */
+#define PCI_DEVICE_ID_RP6M 0x000C /* RocketModem 6 port */
+#define PCI_DEVICE_ID_RP4M 0x000D /* RocketModem 4 port */
+#define PCI_DEVICE_ID_RP2_232 0x000E /* Rocketport Plus 2 port RS232 */
+#define PCI_DEVICE_ID_RP2_422 0x000F /* Rocketport Plus 2 port RS422 */
+
+/* Universal PCI boards */
+#define PCI_DEVICE_ID_URP32INTF 0x0801 /* Rocketport UPCI 32 port w/external I/F */
+#define PCI_DEVICE_ID_URP8INTF 0x0802 /* Rocketport UPCI 8 port w/external I/F */
+#define PCI_DEVICE_ID_URP16INTF 0x0803 /* Rocketport UPCI 16 port w/external I/F */
+#define PCI_DEVICE_ID_URP8OCTA 0x0805 /* Rocketport UPCI 8 port w/octa cable */
+#define PCI_DEVICE_ID_UPCI_RM3_8PORT 0x080C /* Rocketmodem III 8 port */
+#define PCI_DEVICE_ID_UPCI_RM3_4PORT 0x080D /* Rocketmodem III 4 port */
+
+/* Compact PCI device */
+#define PCI_DEVICE_ID_CRP16INTF 0x0903 /* Rocketport Compact PCI 16 port w/external I/F */
+
+#define TTY_GET_LINE(t) t->index
+#define TTY_DRIVER_MINOR_START(t) t->driver->minor_start
+#define TTY_DRIVER_SUBTYPE(t) t->driver->subtype
+#define TTY_DRIVER_NAME(t) t->driver->name
+#define TTY_DRIVER_NAME_BASE(t) t->driver->name_base
+#define TTY_DRIVER_FLUSH_BUFFER_EXISTS(t) t->driver->flush_buffer
+#define TTY_DRIVER_FLUSH_BUFFER(t) t->driver->flush_buffer(t)
+
+