Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/net/dgrs_plx9060.h b/drivers/net/dgrs_plx9060.h
new file mode 100644
index 0000000..6888ae0
--- /dev/null
+++ b/drivers/net/dgrs_plx9060.h
@@ -0,0 +1,175 @@
+/*
+ * PLX 9060 PCI Interface chip
+ */
+
+/*
+ * PCI configuration registers, same offset on local and PCI sides,
+ * but on PCI side, must use PCI BIOS calls to read/write.
+ */
+#define PCI_PLXREGS_BASE_ADDR 0x10
+
+#define PCI_PLXREGS_IO_ADDR 0x14
+
+#define PCI_SPACE0_BASE_ADDR 0x18
+
+#define PCI_ROM_BASE_ADDR 0x30
+# define PCI_ROM_ENABLED 0x00000001
+
+#define PCI_INT_LINE 0x3C
+
+/*
+ * Registers accessible directly from PCI and local side.
+ * Offset is from PCI side. Add PLX_LCL_OFFSET for local address.
+ */
+#define PLX_LCL_OFFSET 0x80 /* Offset of regs from local side */
+
+/*
+ * Local Configuration Registers
+ */
+#define PLX_SPACE0_RANGE 0x00 /* Range for PCI to Lcl Addr Space 0 */
+#define PLX_SPACE0_BASE_ADDR 0x04 /* Lcl Base address remap */
+
+#define PLX_ROM_RANGE 0x10 /* Range for expansion ROM (DMA) */
+#define PLX_ROM_BASE_ADDR 0x14 /* Lcl base address remap for ROM */
+
+#define PLX_BUS_REGION 0x18 /* Bus Region Descriptors */
+
+/*
+ * Shared Run Time Registers
+ */
+#define PLX_MBOX0 0x40
+#define PLX_MBOX1 0x44
+#define PLX_MBOX2 0x48
+#define PLX_MBOX3 0x4C
+#define PLX_MBOX4 0x50
+#define PLX_MBOX5 0x54
+#define PLX_MBOX6 0x58
+#define PLX_MBOX7 0x5C
+
+#define PLX_PCI2LCL_DOORBELL 0x60
+
+#define PLX_LCL2PCI_DOORBELL 0x64
+
+#define PLX_INT_CSR 0x68 /* Interrupt Control/Status */
+# define PLX_LSERR_ENABLE 0x00000001
+# define PLX_LSERR_PE 0x00000002
+# define PLX_SERR 0x00000004
+# undef PLX_UNUSED /* 0x00000008 */
+# undef PLX_UNUSED /* 0x00000010 */
+# undef PLX_UNUSED /* 0x00000020 */
+# undef PLX_UNUSED /* 0x00000040 */
+# undef PLX_UNUSED /* 0x00000080 */
+# define PLX_PCI_IE 0x00000100
+# define PLX_PCI_DOORBELL_IE 0x00000200
+# define PLX_PCI_ABORT_IE 0x00000400
+# define PLX_PCI_LOCAL_IE 0x00000800
+# define PLX_RETRY_ABORT_ENABLE 0x00001000
+# define PLX_PCI_DOORBELL_INT 0x00002000
+# define PLX_PCI_ABORT_INT 0x00004000
+# define PLX_PCI_LOCAL_INT 0x00008000
+# define PLX_LCL_IE 0x00010000
+# define PLX_LCL_DOORBELL_IE 0x00020000
+# define PLX_LCL_DMA0_IE 0x00040000
+# define PLX_LCL_DMA1_IE 0x00080000
+# define PLX_LCL_DOORBELL_INT 0x00100000
+# define PLX_LCL_DMA0_INT 0x00200000
+# define PLX_LCL_DMA1_INT 0x00400000
+# define PLX_LCL_BIST_INT 0x00800000
+# define PLX_BM_DIRECT_ 0x01000000
+# define PLX_BM_DMA0_ 0x02000000
+# define PLX_BM_DMA1_ 0x04000000
+# define PLX_BM_ABORT_ 0x08000000
+# undef PLX_UNUSED /* 0x10000000 */
+# undef PLX_UNUSED /* 0x20000000 */
+# undef PLX_UNUSED /* 0x40000000 */
+# undef PLX_UNUSED /* 0x80000000 */
+
+#define PLX_MISC_CSR 0x6c /* EEPROM,PCI,User,Init Control/Status*/
+# define PLX_USEROUT 0x00010000
+# define PLX_USERIN 0x00020000
+# define PLX_EECK 0x01000000
+# define PLX_EECS 0x02000000
+# define PLX_EEWD 0x04000000
+# define PLX_EERD 0x08000000
+
+/*
+ * DMA registers. Offset is from local side
+ */
+#define PLX_DMA0_MODE 0x100
+# define PLX_DMA_MODE_WIDTH32 0x00000003
+# define PLX_DMA_MODE_WAITSTATES(X) ((X)<<2)
+# define PLX_DMA_MODE_NOREADY 0x00000000
+# define PLX_DMA_MODE_READY 0x00000040
+# define PLX_DMA_MODE_NOBTERM 0x00000000
+# define PLX_DMA_MODE_BTERM 0x00000080
+# define PLX_DMA_MODE_NOBURST 0x00000000
+# define PLX_DMA_MODE_BURST 0x00000100
+# define PLX_DMA_MODE_NOCHAIN 0x00000000
+# define PLX_DMA_MODE_CHAIN 0x00000200
+# define PLX_DMA_MODE_DONE_IE 0x00000400
+# define PLX_DMA_MODE_ADDR_HOLD 0x00000800
+
+#define PLX_DMA0_PCI_ADDR 0x104
+ /* non-chaining mode PCI address */
+
+#define PLX_DMA0_LCL_ADDR 0x108
+ /* non-chaining mode local address */
+
+#define PLX_DMA0_SIZE 0x10C
+ /* non-chaining mode length */
+
+#define PLX_DMA0_DESCRIPTOR 0x110
+# define PLX_DMA_DESC_EOC 0x00000002
+# define PLX_DMA_DESC_TC_IE 0x00000004
+# define PLX_DMA_DESC_TO_HOST 0x00000008
+# define PLX_DMA_DESC_TO_BOARD 0x00000000
+# define PLX_DMA_DESC_NEXTADDR 0xFFFFfff0
+
+#define PLX_DMA1_MODE 0x114
+#define PLX_DMA1_PCI_ADDR 0x118
+#define PLX_DMA1_LCL_ADDR 0x11C
+#define PLX_DMA1_SIZE 0x110
+#define PLX_DMA1_DESCRIPTOR 0x124
+
+#define PLX_DMA_CSR 0x128
+# define PLX_DMA_CSR_0_ENABLE 0x00000001
+# define PLX_DMA_CSR_0_START 0x00000002
+# define PLX_DMA_CSR_0_ABORT 0x00000004
+# define PLX_DMA_CSR_0_CLR_INTR 0x00000008
+# define PLX_DMA_CSR_0_DONE 0x00000010
+# define PLX_DMA_CSR_1_ENABLE 0x00000100
+# define PLX_DMA_CSR_1_START 0x00000200
+# define PLX_DMA_CSR_1_ABORT 0x00000400
+# define PLX_DMA_CSR_1_CLR_INTR 0x00000800
+# define PLX_DMA_CSR_1_DONE 0x00001000
+
+#define PLX_DMA_ARB0 0x12C
+# define PLX_DMA_ARB0_LATENCY_T 0x000000FF
+# define PLX_DMA_ARB0_PAUSE_T 0x0000FF00
+# define PLX_DMA_ARB0_LATENCY_EN 0x00010000
+# define PLX_DMA_ARB0_PAUSE_EN 0x00020000
+# define PLX_DMA_ARB0_BREQ_EN 0x00040000
+# define PLX_DMA_ARB0_PRI 0x00180000
+# define PLX_DMA_ARB0_PRI_ROUND 0x00000000
+# define PLX_DMA_ARB0_PRI_0 0x00080000
+# define PLX_DMA_ARB0_PRI_1 0x00100000
+
+#define PLX_DMA_ARB1 0x130
+ /* Chan 0: FIFO DEPTH=16 */
+# define PLX_DMA_ARB1_0_P2L_LW_TRIG(X) ( ((X)&15) << 0 )
+# define PLX_DMA_ARB1_0_L2P_LR_TRIG(X) ( ((X)&15) << 4 )
+# define PLX_DMA_ARB1_0_L2P_PW_TRIG(X) ( ((X)&15) << 8 )
+# define PLX_DMA_ARB1_0_P2L_PR_TRIG(X) ( ((X)&15) << 12 )
+ /* Chan 1: FIFO DEPTH=8 */
+# define PLX_DMA_ARB1_1_P2L_LW_TRIG(X) ( ((X)& 7) << 16 )
+# define PLX_DMA_ARB1_1_L2P_LR_TRIG(X) ( ((X)& 7) << 20 )
+# define PLX_DMA_ARB1_1_L2P_PW_TRIG(X) ( ((X)& 7) << 24 )
+# define PLX_DMA_ARB1_1_P2L_PR_TRIG(X) ( ((X)& 7) << 28 )
+
+typedef struct _dmachain
+{
+ ulong pciaddr;
+ ulong lcladdr;
+ ulong len;
+ ulong next;
+} DMACHAIN;