wil6210: add oob_mode module parameter
Add module parameter oob_mode. Takes effect the next time
the interface is brought up and FW is loaded. Puts the FW
in special "out of the box" (OOB) mode which is used for
diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index c2a0a66..8d4e884 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -27,6 +27,11 @@
module_param(debug_fw, bool, S_IRUGO);
MODULE_PARM_DESC(debug_fw, " do not perform card reset. For FW debug");
+static bool oob_mode;
+module_param(oob_mode, bool, S_IRUGO);
+MODULE_PARM_DESC(oob_mode,
+ " enable out of the box (OOB) mode in FW, for diagnostics and certification");
+
bool no_fw_recovery;
module_param(no_fw_recovery, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(no_fw_recovery, " disable automatic FW error recovery");
@@ -547,6 +552,16 @@
wil_w(wil, RGF_USER_USER_CPU_0, 1);
}
+static void wil_set_oob_mode(struct wil6210_priv *wil, bool enable)
+{
+ wil_info(wil, "%s: enable=%d\n", __func__, enable);
+ if (enable) {
+ wil_s(wil, RGF_USER_USAGE_6, BIT_USER_OOB_MODE);
+ } else {
+ wil_c(wil, RGF_USER_USAGE_6, BIT_USER_OOB_MODE);
+ }
+}
+
static int wil_target_reset(struct wil6210_priv *wil)
{
int delay = 0;
@@ -823,6 +838,7 @@
if (rc)
return rc;
+ wil_set_oob_mode(wil, oob_mode);
if (load_fw) {
wil_info(wil, "Use firmware <%s> + board <%s>\n", WIL_FW_NAME,
WIL_FW2_NAME);
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index d18c448..4d699ea4 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -132,6 +132,7 @@
/* registers - FW addresses */
#define RGF_USER_USAGE_1 (0x880004)
#define RGF_USER_USAGE_6 (0x880018)
+ #define BIT_USER_OOB_MODE BIT(31)
#define RGF_USER_HW_MACHINE_STATE (0x8801dc)
#define HW_MACHINE_BOOT_DONE (0x3fffffd)
#define RGF_USER_USER_CPU_0 (0x8801e0)