bonding: allow arp_ip_targets on separate vlans to use arp validation
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation. A configuration like this, now works:
BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1
Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 3f0071c..6a42a14 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -2615,6 +2615,17 @@
unsigned char *arp_ptr;
__be32 sip, tip;
+ if (dev->priv_flags & IFF_802_1Q_VLAN) {
+ /*
+ * When using VLANS and bonding, dev and oriv_dev may be
+ * incorrect if the physical interface supports VLAN
+ * acceleration. With this change ARP validation now
+ * works for hosts only reachable on the VLAN interface.
+ */
+ dev = vlan_dev_real_dev(dev);
+ orig_dev = dev_get_by_index_rcu(dev_net(skb->dev),skb->skb_iif);
+ }
+
if (!(dev->priv_flags & IFF_BONDING) || !(dev->flags & IFF_MASTER))
goto out;
diff --git a/net/8021q/vlan_core.c b/net/8021q/vlan_core.c
index e75a2f3..c0316e0 100644
--- a/net/8021q/vlan_core.c
+++ b/net/8021q/vlan_core.c
@@ -14,6 +14,7 @@
if (skb_bond_should_drop(skb))
goto drop;
+ skb->skb_iif = skb->dev->ifindex;
__vlan_hwaccel_put_tag(skb, vlan_tci);
skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK);
@@ -85,6 +86,7 @@
if (skb_bond_should_drop(skb))
goto drop;
+ skb->skb_iif = skb->dev->ifindex;
__vlan_hwaccel_put_tag(skb, vlan_tci);
skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK);
diff --git a/net/core/dev.c b/net/core/dev.c
index a8d68cd..f9aa699 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -2495,12 +2495,26 @@
if (!skb)
goto out;
+ /*
+ * Make sure frames received on VLAN interfaces stacked on
+ * bonding interfaces still make their way to any base bonding
+ * device that may have registered for a specific ptype. The
+ * handler may have to adjust skb->dev and orig_dev.
+ *
+ * null_or_orig can be overloaded since it will not be set when
+ * using VLANs on top of bonding. Putting it here prevents
+ * disturbing the ptype_all handlers above.
+ */
+ if ((skb->dev->priv_flags & IFF_802_1Q_VLAN) &&
+ (vlan_dev_real_dev(skb->dev)->priv_flags & IFF_BONDING)) {
+ null_or_orig = vlan_dev_real_dev(skb->dev);
+ }
+
type = skb->protocol;
list_for_each_entry_rcu(ptype,
&ptype_base[ntohs(type) & PTYPE_HASH_MASK], list) {
- if (ptype->type == type &&
- (ptype->dev == null_or_orig || ptype->dev == skb->dev ||
- ptype->dev == orig_dev)) {
+ if (ptype->type == type && (ptype->dev == null_or_orig ||
+ ptype->dev == skb->dev || ptype->dev == orig_dev)) {
if (pt_prev)
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = ptype;