ARM: mach-shmobile: ap4evb: Add HDMI sound support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c
index 46ca4d4..32d9e28 100644
--- a/arch/arm/mach-shmobile/board-ap4evb.c
+++ b/arch/arm/mach-shmobile/board-ap4evb.c
@@ -565,12 +565,50 @@
/* FSI */
#define IRQ_FSI evt2irq(0x1840)
+
+static int fsi_set_rate(int is_porta, int rate)
+{
+ struct clk *fsib_clk;
+ struct clk *fdiv_clk = &sh7372_fsidivb_clk;
+ int ret;
+
+ /* set_rate is not needed if port A */
+ if (is_porta)
+ return 0;
+
+ fsib_clk = clk_get(NULL, "fsib_clk");
+ if (IS_ERR(fsib_clk))
+ return -EINVAL;
+
+ switch (rate) {
+ case 48000:
+ clk_set_rate(fsib_clk, clk_round_rate(fsib_clk, 85428000));
+ clk_set_rate(fdiv_clk, clk_round_rate(fdiv_clk, 12204000));
+ ret = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
+ break;
+ default:
+ pr_err("unsupported rate in FSI2 port B\n");
+ ret = -EINVAL;
+ break;
+ }
+
+ clk_put(fsib_clk);
+
+ return ret;
+}
+
static struct sh_fsi_platform_info fsi_info = {
.porta_flags = SH_FSI_BRS_INV |
SH_FSI_OUT_SLAVE_MODE |
SH_FSI_IN_SLAVE_MODE |
SH_FSI_OFMT(PCM) |
SH_FSI_IFMT(PCM),
+
+ .portb_flags = SH_FSI_BRS_INV |
+ SH_FSI_BRM_INV |
+ SH_FSI_LRS_INV |
+ SH_FSI_OFMT(SPDIF),
+ .set_rate = fsi_set_rate,
};
static struct resource fsi_resources[] = {
@@ -634,6 +672,7 @@
static struct sh_mobile_hdmi_info hdmi_info = {
.lcd_chan = &sh_mobile_lcdc1_info.ch[0],
.lcd_dev = &lcdc1_device.dev,
+ .flags = HDMI_SND_SRC_SPDIF,
};
static struct resource hdmi_resources[] = {
@@ -992,6 +1031,7 @@
#define GPIO_PORT9CR 0xE6051009
#define GPIO_PORT10CR 0xE605100A
+#define USCCR1 0xE6058144
static void __init ap4evb_init(void)
{
u32 srcr4;
@@ -1062,7 +1102,7 @@
/* setup USB phy */
__raw_writew(0x8a0a, 0xE6058130); /* USBCR2 */
- /* enable FSI2 */
+ /* enable FSI2 port A (ak4643) */
gpio_request(GPIO_FN_FSIAIBT, NULL);
gpio_request(GPIO_FN_FSIAILR, NULL);
gpio_request(GPIO_FN_FSIAISLD, NULL);
@@ -1079,6 +1119,10 @@
gpio_request(GPIO_PORT41, NULL);
gpio_direction_input(GPIO_PORT41);
+ /* setup FSI2 port B (HDMI) */
+ gpio_request(GPIO_FN_FSIBCK, NULL);
+ __raw_writew(__raw_readw(USCCR1) & ~(1 << 6), USCCR1); /* use SPDIF */
+
/* set SPU2 clock to 119.6 MHz */
clk = clk_get(NULL, "spu_clk");
if (!IS_ERR(clk)) {