wil6210: boot loader
Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.
Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader
The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
calibrations and parameters)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index b04e0af..acbbd27 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -29,10 +29,6 @@
module_param(no_fw_recovery, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(no_fw_recovery, " disable automatic FW error recovery");
-static bool no_fw_load = true;
-module_param(no_fw_load, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(no_fw_load, " do not download FW, use one in on-card flash.");
-
/* if not set via modparam, will be set to default value of 1/8 of
* rx ring size during init flow
*/
@@ -532,6 +528,8 @@
wil_halt_cpu(wil);
+ /* clear all boot loader "ready" bits */
+ W(RGF_USER_BL + offsetof(struct RGF_BL, ready), 0);
/* Clear Fw Download notification */
C(RGF_USER_USAGE_6, BIT(0));
@@ -583,16 +581,16 @@
/* TODO: check order here!!! Erez code is different */
W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
- /* wait until device ready. typical time is 200..250 msec */
+ /* wait until device ready. typical time is 20..80 msec */
do {
msleep(RST_DELAY);
- x = R(RGF_USER_HW_MACHINE_STATE);
+ x = R(RGF_USER_BL + offsetof(struct RGF_BL, ready));
if (delay++ > RST_COUNT) {
- wil_err(wil, "Reset not completed, hw_state 0x%08x\n",
+ wil_err(wil, "Reset not completed, bl.ready 0x%08x\n",
x);
return -ETIME;
}
- } while (x != HW_MACHINE_BOOT_DONE);
+ } while (!(x & BIT_BL_READY));
if (!is_reset_v2)
W(RGF_PCIE_LOS_COUNTER_CTL, BIT(8));
@@ -603,11 +601,6 @@
return 0;
}
-#undef R
-#undef W
-#undef S
-#undef C
-
void wil_mbox_ring_le2cpus(struct wil6210_mbox_ring *r)
{
le32_to_cpus(&r->base);
@@ -617,6 +610,32 @@
le32_to_cpus(&r->head);
}
+static int wil_get_bl_info(struct wil6210_priv *wil)
+{
+ struct net_device *ndev = wil_to_ndev(wil);
+ struct RGF_BL bl;
+
+ wil_memcpy_fromio_32(&bl, wil->csr + HOSTADDR(RGF_USER_BL), sizeof(bl));
+ le32_to_cpus(&bl.ready);
+ le32_to_cpus(&bl.version);
+ le32_to_cpus(&bl.rf_type);
+ le32_to_cpus(&bl.baseband_type);
+
+ if (!is_valid_ether_addr(bl.mac_address)) {
+ wil_err(wil, "BL: Invalid MAC %pM\n", bl.mac_address);
+ return -EINVAL;
+ }
+
+ ether_addr_copy(ndev->perm_addr, bl.mac_address);
+ if (!is_valid_ether_addr(ndev->dev_addr))
+ ether_addr_copy(ndev->dev_addr, bl.mac_address);
+ wil_info(wil,
+ "Boot Loader: ver = %d MAC = %pM RF = 0x%08x bband = 0x%08x\n",
+ bl.version, bl.mac_address, bl.rf_type, bl.baseband_type);
+
+ return 0;
+}
+
static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
{
ulong to = msecs_to_jiffies(1000);
@@ -637,7 +656,7 @@
* After calling this routine, you're expected to reload
* the firmware.
*/
-int wil_reset(struct wil6210_priv *wil)
+int wil_reset(struct wil6210_priv *wil, bool load_fw)
{
int rc;
@@ -675,30 +694,36 @@
if (rc)
return rc;
- if (!no_fw_load) {
- wil_info(wil, "Use firmware <%s>\n", WIL_FW_NAME);
+ rc = wil_get_bl_info(wil);
+ if (rc)
+ return rc;
+
+ if (load_fw) {
+ wil_info(wil, "Use firmware <%s> + board <%s>\n", WIL_FW_NAME,
+ WIL_FW2_NAME);
+
wil_halt_cpu(wil);
/* Loading f/w from the file */
rc = wil_request_firmware(wil, WIL_FW_NAME);
if (rc)
return rc;
+ rc = wil_request_firmware(wil, WIL_FW2_NAME);
+ if (rc)
+ return rc;
- /* clear any interrupts which on-card-firmware may have set */
+ /* Mark FW as loaded from host */
+ S(RGF_USER_USAGE_6, 1);
+
+ /* clear any interrupts which on-card-firmware
+ * may have set
+ */
wil6210_clear_irq(wil);
- { /* CAF_ICR - clear and mask */
- u32 a = HOSTADDR(RGF_CAF_ICR) +
- offsetof(struct RGF_ICR, ICR);
- u32 m = HOSTADDR(RGF_CAF_ICR) +
- offsetof(struct RGF_ICR, IMV);
- u32 icr = ioread32(wil->csr + a);
+ /* CAF_ICR - clear and mask */
+ /* it is W1C, clear by writing back same value */
+ S(RGF_CAF_ICR + offsetof(struct RGF_ICR, ICR), 0);
+ W(RGF_CAF_ICR + offsetof(struct RGF_ICR, IMV), ~0);
- iowrite32(icr, wil->csr + a); /* W1C */
- iowrite32(~0, wil->csr + m);
- wmb(); /* wait for completion */
- }
wil_release_cpu(wil);
- } else {
- wil_info(wil, "Use firmware from on-card flash\n");
}
/* init after reset */
@@ -706,15 +731,22 @@
reinit_completion(&wil->wmi_ready);
reinit_completion(&wil->wmi_call);
- wil_configure_interrupt_moderation(wil);
- wil_unmask_irq(wil);
+ if (load_fw) {
+ wil_configure_interrupt_moderation(wil);
+ wil_unmask_irq(wil);
- /* we just started MAC, wait for FW ready */
- rc = wil_wait_for_fw_ready(wil);
+ /* we just started MAC, wait for FW ready */
+ rc = wil_wait_for_fw_ready(wil);
+ }
return rc;
}
+#undef R
+#undef W
+#undef S
+#undef C
+
void wil_fw_error_recovery(struct wil6210_priv *wil)
{
wil_dbg_misc(wil, "starting fw error recovery\n");
@@ -730,7 +762,7 @@
WARN_ON(!mutex_is_locked(&wil->mutex));
- rc = wil_reset(wil);
+ rc = wil_reset(wil, true);
if (rc)
return rc;
@@ -837,7 +869,7 @@
if (!iter)
wil_err(wil, "timeout waiting for idle FW/HW\n");
- wil_rx_fini(wil);
+ wil_reset(wil, false);
return 0;
}