diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a91009c..9c24746 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1021,8 +1021,6 @@
 
 source "arch/arm/mach-ks8695/Kconfig"
 
-source "arch/arm/mach-lpc32xx/Kconfig"
-
 source "arch/arm/mach-msm/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"
diff --git a/arch/arm/boot/dts/ea3250.dts b/arch/arm/boot/dts/ea3250.dts
new file mode 100644
index 0000000..c07ba8c
--- /dev/null
+++ b/arch/arm/boot/dts/ea3250.dts
@@ -0,0 +1,157 @@
+/*
+ * Embedded Artists LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "lpc32xx.dtsi"
+
+/ {
+	model = "Embedded Artists LPC3250 board based on NXP LPC3250";
+	compatible = "ea,ea3250", "nxp,lpc3250";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x4000000>;
+	};
+
+	ahb {
+		mac: ethernet@31060000 {
+			phy-mode = "rmii";
+			use-iram;
+		};
+
+		/* Here, choose exactly one from: ohci, usbd */
+		ohci@31020000 {
+			transceiver = <&isp1301>;
+			status = "okay";
+		};
+
+/*
+		usbd@31020000 {
+			transceiver = <&isp1301>;
+			status = "okay";
+		};
+*/
+
+		/* 128MB Flash via SLC NAND controller */
+		slc: flash@20020000 {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			nxp,wdr-clks = <14>;
+			nxp,wwidth = <260000000>;
+			nxp,whold = <104000000>;
+			nxp,wsetup = <200000000>;
+			nxp,rdr-clks = <14>;
+			nxp,rwidth = <34666666>;
+			nxp,rhold = <104000000>;
+			nxp,rsetup = <200000000>;
+			nand-on-flash-bbt;
+			gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+			mtd0@00000000 {
+				label = "ea3250-boot";
+				reg = <0x00000000 0x00080000>;
+				read-only;
+			};
+
+			mtd1@00080000 {
+				label = "ea3250-uboot";
+				reg = <0x00080000 0x000c0000>;
+				read-only;
+			};
+
+			mtd2@00140000 {
+				label = "ea3250-kernel";
+				reg = <0x00140000 0x00400000>;
+			};
+
+			mtd3@00540000 {
+				label = "ea3250-rootfs";
+				reg = <0x00540000 0x07ac0000>;
+			};
+		};
+
+		apb {
+			uart5: serial@40090000 {
+				status = "okay";
+			};
+
+			uart3: serial@40080000 {
+				status = "okay";
+			};
+
+			uart6: serial@40098000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@400A0000 {
+				clock-frequency = <100000>;
+
+				eeprom@50 {
+					compatible = "at,24c256";
+					reg = <0x50>;
+				};
+
+				eeprom@57 {
+					compatible = "at,24c64";
+					reg = <0x57>;
+				};
+
+				uda1380: uda1380@18 {
+					compatible = "nxp,uda1380";
+					reg = <0x18>;
+					power-gpio = <&gpio 0x59 0>;
+					reset-gpio = <&gpio 0x51 0>;
+					dac-clk = "wspll";
+				};
+
+				pca9532: pca9532@60 {
+					compatible = "nxp,pca9532";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x60>;
+				};
+			};
+
+			i2c2: i2c@400A8000 {
+				clock-frequency = <100000>;
+			};
+
+			i2cusb: i2c@31020300 {
+				clock-frequency = <100000>;
+
+				isp1301: usb-transceiver@2d {
+					compatible = "nxp,isp1301";
+					reg = <0x2d>;
+				};
+			};
+
+			sd@20098000 {
+				wp-gpios = <&pca9532 5 0>;
+				cd-gpios = <&pca9532 4 0>;
+				cd-inverted;
+				bus-width = <4>;
+				status = "okay";
+			};
+		};
+
+		fab {
+			uart1: serial@40014000 {
+				status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi
index 3f5dad8..c5f37fb 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/lpc32xx.dtsi
@@ -35,13 +35,14 @@
 		slc: flash@20020000 {
 			compatible = "nxp,lpc3220-slc";
 			reg = <0x20020000 0x1000>;
-			status = "disable";
+			status = "disabled";
 		};
 
-		mlc: flash@200B0000 {
+		mlc: flash@200a8000 {
 			compatible = "nxp,lpc3220-mlc";
-			reg = <0x200B0000 0x1000>;
-			status = "disable";
+			reg = <0x200a8000 0x11000>;
+			interrupts = <11 0>;
+			status = "disabled";
 		};
 
 		dma@31000000 {
@@ -57,21 +58,21 @@
 			compatible = "nxp,ohci-nxp", "usb-ohci";
 			reg = <0x31020000 0x300>;
 			interrupts = <0x3b 0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		usbd@31020000 {
 			compatible = "nxp,lpc3220-udc";
 			reg = <0x31020000 0x300>;
 			interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		clcd@31040000 {
 			compatible = "arm,pl110", "arm,primecell";
 			reg = <0x31040000 0x1000>;
 			interrupts = <0x0e 0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		mac: ethernet@31060000 {
@@ -114,9 +115,10 @@
 			};
 
 			sd@20098000 {
-				compatible = "arm,pl180", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				reg = <0x20098000 0x1000>;
 				interrupts = <0x0f 0>, <0x0d 0>;
+				status = "disabled";
 			};
 
 			i2s1: i2s@2009C000 {
@@ -124,24 +126,42 @@
 				reg = <0x2009C000 0x1000>;
 			};
 
+			/* UART5 first since it is the default console, ttyS0 */
+			uart5: serial@40090000 {
+				/* actually, ns16550a w/ 64 byte fifos! */
+				compatible = "nxp,lpc3220-uart";
+				reg = <0x40090000 0x1000>;
+				interrupts = <9 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
 			uart3: serial@40080000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-uart";
 				reg = <0x40080000 0x1000>;
+				interrupts = <7 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
 			};
 
 			uart4: serial@40088000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-uart";
 				reg = <0x40088000 0x1000>;
-			};
-
-			uart5: serial@40090000 {
-				compatible = "nxp,serial";
-				reg = <0x40090000 0x1000>;
+				interrupts = <8 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
 			};
 
 			uart6: serial@40098000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-uart";
 				reg = <0x40098000 0x1000>;
+				interrupts = <10 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
 			};
 
 			i2c1: i2c@400A0000 {
@@ -192,18 +212,24 @@
 			};
 
 			uart1: serial@40014000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-hsuart";
 				reg = <0x40014000 0x1000>;
+				interrupts = <26 0>;
+				status = "disabled";
 			};
 
 			uart2: serial@40018000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-hsuart";
 				reg = <0x40018000 0x1000>;
+				interrupts = <25 0>;
+				status = "disabled";
 			};
 
-			uart7: serial@4001C000 {
-				compatible = "nxp,serial";
-				reg = <0x4001C000 0x1000>;
+			uart7: serial@4001c000 {
+				compatible = "nxp,lpc3220-hsuart";
+				reg = <0x4001c000 0x1000>;
+				interrupts = <24 0>;
+				status = "disabled";
 			};
 
 			rtc@40024000 {
@@ -235,19 +261,21 @@
 				compatible = "nxp,lpc3220-adc";
 				reg = <0x40048000 0x1000>;
 				interrupts = <0x27 0>;
-				status = "disable";
+				status = "disabled";
 			};
 
 			tsc@40048000 {
 				compatible = "nxp,lpc3220-tsc";
 				reg = <0x40048000 0x1000>;
 				interrupts = <0x27 0>;
-				status = "disable";
+				status = "disabled";
 			};
 
 			key@40050000 {
 				compatible = "nxp,lpc3220-key";
 				reg = <0x40050000 0x1000>;
+				interrupts = <54 0>;
+				status = "disabled";
 			};
 
 		};
diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts
index c4ff6d1..802ec5b 100644
--- a/arch/arm/boot/dts/phy3250.dts
+++ b/arch/arm/boot/dts/phy3250.dts
@@ -54,6 +54,17 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			nxp,wdr-clks = <14>;
+			nxp,wwidth = <40000000>;
+			nxp,whold = <100000000>;
+			nxp,wsetup = <100000000>;
+			nxp,rdr-clks = <14>;
+			nxp,rwidth = <40000000>;
+			nxp,rhold = <66666666>;
+			nxp,rsetup = <100000000>;
+			nand-on-flash-bbt;
+			gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
 			mtd0@00000000 {
 				label = "phy3250-boot";
 				reg = <0x00000000 0x00064000>;
@@ -83,6 +94,14 @@
 		};
 
 		apb {
+			uart5: serial@40090000 {
+				status = "okay";
+			};
+
+			uart3: serial@40080000 {
+				status = "okay";
+			};
+
 			i2c1: i2c@400A0000 {
 				clock-frequency = <100000>;
 
@@ -114,16 +133,58 @@
 			};
 
 			ssp0: ssp@20084000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pl022,num-chipselects = <1>;
+				cs-gpios = <&gpio 3 5 0>;
+
 				eeprom: at25@0 {
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable = <0>;
+					pl022,com-mode = <0>;
+					pl022,rx-level-trig = <1>;
+					pl022,tx-level-trig = <1>;
+					pl022,ctrl-len = <11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+
+					at25,byte-len = <0x8000>;
+					at25,addr-mode = <2>;
+					at25,page-size = <64>;
+
 					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <5000000>;
 				};
 			};
+
+			sd@20098000 {
+				wp-gpios = <&gpio 3 0 0>;
+				cd-gpios = <&gpio 3 1 0>;
+				cd-inverted;
+				bus-width = <4>;
+				status = "okay";
+			};
 		};
 
 		fab {
+			uart2: serial@40018000 {
+				status = "okay";
+			};
+
 			tsc@40048000 {
 				status = "okay";
 			};
+
+			key@40050000 {
+				status = "okay";
+				keypad,num-rows = <1>;
+				keypad,num-columns = <1>;
+				nxp,debounce-delay-ms = <3>;
+				nxp,scan-delay-ms = <34>;
+				linux,keymap = <0x00000002>;
+			};
 		};
 	};
 
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index e05a2f1..78ed575 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -2,7 +2,10 @@
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
 CONFIG_EXPERT=y
 # CONFIG_COMPAT_BRK is not set
 CONFIG_SLAB=y
@@ -36,8 +39,6 @@
 CONFIG_MACH_IMX27_DT=y
 CONFIG_MXC_IRQ_PRIOR=y
 CONFIG_MXC_PWM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
@@ -46,7 +47,6 @@
 CONFIG_FPE_NWFPE_XP=y
 CONFIG_PM_DEBUG=y
 CONFIG_NET=y
-CONFIG_SMSC911X=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
@@ -70,31 +70,31 @@
 CONFIG_MTD_CFI_ADV_OPTIONS=y
 CONFIG_MTD_CFI_GEOMETRY=y
 # CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
-CONFIG_MTD_MAP_BANK_WIDTH_4=y
 # CONFIG_MTD_CFI_I2 is not set
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_MXC=y
 CONFIG_MTD_UBI=y
-CONFIG_MISC_DEVICES=y
 CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
+CONFIG_ATA=y
+CONFIG_PATA_IMX=y
 CONFIG_NETDEVICES=y
 CONFIG_CS89x0=y
 CONFIG_CS89x0_PLATFORM=y
 CONFIG_DM9000=y
 CONFIG_SMC91X=y
 CONFIG_SMC911X=y
+CONFIG_SMSC911X=y
 CONFIG_SMSC_PHY=y
 # CONFIG_INPUT_MOUSEDEV is not set
 CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
+CONFIG_KEYBOARD_IMX=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=m
-CONFIG_TOUCHSCREEN_MC13783=m
-# CONFIG_SERIO is not set
+CONFIG_TOUCHSCREEN_MC13783=y
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=m
 CONFIG_SERIAL_IMX=y
@@ -113,31 +113,23 @@
 CONFIG_SENSORS_MC13783_ADC=m
 CONFIG_WATCHDOG=y
 CONFIG_IMX2_WDT=y
-CONFIG_MFD_MC13XXX=y
+CONFIG_MFD_MC13XXX_SPI=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_MC13783=y
 CONFIG_REGULATOR_MC13892=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_SOC_CAMERA_OV2640=y
+CONFIG_VIDEO_MX2=y
 CONFIG_FB=y
 CONFIG_FB_IMX=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_LCD_L4F00242T03=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_VIDEO_DEV=y
-CONFIG_VIDEO_V4L2_COMMON=y
-CONFIG_VIDEO_MEDIA=y
-CONFIG_VIDEO_V4L2=y
-CONFIG_VIDEOBUF_GEN=y
-CONFIG_VIDEOBUF_DMA_CONTIG=y
-CONFIG_VIDEOBUF2_CORE=y
-CONFIG_VIDEO_CAPTURE_DRIVERS=y
-CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_SOC_CAMERA=y
-CONFIG_SOC_CAMERA_OV2640=y
-CONFIG_VIDEO_MX2_HOSTSUPPORT=y
-CONFIG_VIDEO_MX2=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_PWM=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FONTS=y
@@ -152,13 +144,17 @@
 CONFIG_SND_SOC_MX27VIS_AIC32X4=y
 CONFIG_SND_SOC_PHYCORE_AC97=y
 CONFIG_SND_SOC_EUKREA_TLV320=y
+CONFIG_SND_SOC_IMX_SGTL5000=y
+CONFIG_SND_SOC_IMX_MC13783=y
 CONFIG_USB_HID=m
 CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_MXC=y
 CONFIG_USB_ULPI=y
 CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_MMC_MXC=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
@@ -173,22 +169,25 @@
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_PCF8563=y
 CONFIG_RTC_DRV_IMXDI=y
+CONFIG_RTC_DRV_MC13XXX=y
 CONFIG_RTC_DRV_MXC=y
 CONFIG_DMADEVICES=y
 CONFIG_IMX_SDMA=y
 CONFIG_IMX_DMA=y
+CONFIG_COMMON_CLK_DEBUG=y
 # CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_PROC_PAGE_MONITOR is not set
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
 CONFIG_UBIFS_FS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_15=m
-CONFIG_SYSCTL_SYSCALL_CHECK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index b1d3675..f725b96 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -2,6 +2,8 @@
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_KERNEL_LZO=y
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=18
 CONFIG_CGROUPS=y
 CONFIG_RELAY=y
@@ -29,15 +31,12 @@
 CONFIG_MACH_VPR200=y
 CONFIG_MACH_IMX51_DT=y
 CONFIG_MACH_MX51_3DS=y
-CONFIG_MACH_EUKREA_CPUIMX51=y
 CONFIG_MACH_EUKREA_CPUIMX51SD=y
 CONFIG_MACH_MX51_EFIKAMX=y
 CONFIG_MACH_MX51_EFIKASB=y
 CONFIG_MACH_IMX53_DT=y
 CONFIG_SOC_IMX6Q=y
 CONFIG_MXC_PWM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_SMP=y
 CONFIG_VMSPLIT_2G=y
 CONFIG_PREEMPT_VOLUNTARY=y
@@ -64,17 +63,29 @@
 # CONFIG_WIRELESS is not set
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+CONFIG_CONNECTOR=y
 CONFIG_MTD=y
-CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
 CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_M25P80=y
 CONFIG_MTD_SST25L=y
-# CONFIG_STANDALONE is not set
-CONFIG_CONNECTOR=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_GPMI_NAND=y
+CONFIG_MTD_NAND_MXC=y
+CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=65536
+CONFIG_EEPROM_AT24=y
+CONFIG_EEPROM_AT25=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
 CONFIG_SCSI_MULTI_LUN=y
@@ -105,8 +116,11 @@
 CONFIG_INPUT_EVDEV=y
 CONFIG_INPUT_EVBUG=m
 CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_IMX=y
 CONFIG_MOUSE_PS2=m
 CONFIG_MOUSE_PS2_ELANTECH=y
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_MC13783=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_MMA8450=y
 CONFIG_SERIO_SERPORT=m
@@ -116,6 +130,7 @@
 CONFIG_SERIAL_IMX=y
 CONFIG_SERIAL_IMX_CONSOLE=y
 CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_MXC_RNGA=y
 CONFIG_I2C=y
 # CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
@@ -130,42 +145,37 @@
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_IMX2_WDT=y
-CONFIG_MFD_MC13XXX=y
+CONFIG_MFD_MC13XXX_SPI=y
+CONFIG_MFD_MC13XXX_I2C=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_MC13783=y
 CONFIG_REGULATOR_MC13892=y
 CONFIG_MEDIA_SUPPORT=y
-CONFIG_VIDEO_V4L2=y
 CONFIG_VIDEO_DEV=y
-CONFIG_VIDEO_V4L2_COMMON=y
-CONFIG_VIDEOBUF_GEN=y
-CONFIG_VIDEOBUF2_CORE=y
-CONFIG_VIDEOBUF2_MEMOPS=y
-CONFIG_VIDEOBUF2_DMA_CONTIG=y
-CONFIG_VIDEO_CAPTURE_DRIVERS=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_SOC_CAMERA=y
 CONFIG_SOC_CAMERA_OV2640=y
-CONFIG_MX3_VIDEO=y
 CONFIG_VIDEO_MX3=y
 CONFIG_FB=y
-CONFIG_FB_MX3=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_L4F00242T03=y
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_GENERIC=y
-CONFIG_DUMMY_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
 CONFIG_FONTS=y
 CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_IMX_SOC=y
+CONFIG_SND_SOC_PHYCORE_AC97=y
+CONFIG_SND_SOC_EUKREA_TLV320=y
+CONFIG_SND_SOC_IMX_SGTL5000=y
+CONFIG_SND_SOC_IMX_MC13783=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_MXC=y
@@ -178,9 +188,12 @@
 CONFIG_LEDS_CLASS=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_MC13XXX=y
 CONFIG_RTC_DRV_MXC=y
 CONFIG_DMADEVICES=y
 CONFIG_IMX_SDMA=y
+CONFIG_COMMON_CLK_DEBUG=y
+# CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
@@ -204,8 +217,9 @@
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_CONFIGFS_FS=m
+CONFIG_JFFS2_FS=y
+CONFIG_UBIFS_FS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
@@ -216,14 +230,11 @@
 CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=y
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_FTRACE is not set
 # CONFIG_ARM_UNWIND is not set
 CONFIG_SECURITYFS=y
-CONFIG_CRYPTO_DEFLATE=m
-CONFIG_CRYPTO_LZO=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 # CONFIG_CRYPTO_HW is not set
 CONFIG_CRC_CCITT=m
diff --git a/arch/arm/configs/lpc32xx_defconfig b/arch/arm/configs/lpc32xx_defconfig
index 4fa6054..e42a0e3 100644
--- a/arch/arm/configs/lpc32xx_defconfig
+++ b/arch/arm/configs/lpc32xx_defconfig
@@ -1,5 +1,7 @@
 CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
@@ -16,8 +18,7 @@
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_LPC32XX=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
+CONFIG_KEYBOARD_GPIO_POLLED=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
@@ -52,13 +53,17 @@
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_MUSEUM_IDS=y
+CONFIG_MTD_NAND_SLC_LPC32XX=y
+CONFIG_MTD_NAND_MLC_LPC32XX=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_CRYPTOLOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=1
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
@@ -79,16 +84,23 @@
 # CONFIG_NET_VENDOR_STMICRO is not set
 CONFIG_SMSC_PHY=y
 # CONFIG_WLAN is not set
+CONFIG_INPUT_MATRIXKMAP=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_MOUSEDEV_SCREEN_X=240
 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320
 CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_LPC32XX=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_LPC32XX=y
+CONFIG_SERIO_LIBPS2=y
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_HS_LPC32XX=y
+CONFIG_SERIAL_OF_PLATFORM=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -96,7 +108,8 @@
 CONFIG_SPI=y
 CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_DS620=y
+CONFIG_SENSORS_MAX6639=y
 CONFIG_WATCHDOG=y
 CONFIG_PNX4008_WATCHDOG=y
 CONFIG_FB=y
@@ -133,6 +146,8 @@
 CONFIG_MMC_ARMMMCI=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_PCA9532=y
+CONFIG_LEDS_PCA9532_GPIO=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_TIMER=y
@@ -146,10 +161,10 @@
 CONFIG_RTC_DRV_PCF8563=y
 CONFIG_RTC_DRV_LPC32XX=y
 CONFIG_DMADEVICES=y
-CONFIG_AMBA_PL08X=y
 CONFIG_STAGING=y
-CONFIG_IIO=y
 CONFIG_LPC32XX_ADC=y
+CONFIG_MAX517=y
+CONFIG_IIO=y
 CONFIG_EXT2_FS=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_MSDOS_FS=y
@@ -159,7 +174,6 @@
 CONFIG_JFFS2_FS_WBUF_VERIFY=y
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=y
diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index 5406c23..ccdb635 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -28,6 +28,7 @@
 CONFIG_MACH_STMP378X_DEVB=y
 CONFIG_MACH_TX28=y
 CONFIG_MACH_M28EVK=y
+CONFIG_MACH_APX4DEVKIT=y
 # CONFIG_ARM_THUMB is not set
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -58,6 +59,9 @@
 CONFIG_DEVTMPFS=y
 # CONFIG_FIRMWARE_IN_KERNEL is not set
 # CONFIG_BLK_DEV is not set
+CONFIG_MTD=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_GPMI_NAND=y
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_ENC28J60=y
@@ -77,6 +81,7 @@
 # CONFIG_DEVKMEM is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_MXS_AUART=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 # CONFIG_I2C_COMPAT is not set
@@ -109,8 +114,10 @@
 CONFIG_MMC_MXS=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_DS1307=m
+CONFIG_RTC_DRV_STMP=y
 CONFIG_DMADEVICES=y
 CONFIG_MXS_DMA=y
+CONFIG_COMMON_CLK_DEBUG=y
 CONFIG_EXT3_FS=y
 # CONFIG_DNOTIFY is not set
 CONFIG_FSCACHE=m
diff --git a/arch/arm/configs/tegra_defconfig b/arch/arm/configs/tegra_defconfig
index 1198dd6..4be9c1e 100644
--- a/arch/arm/configs/tegra_defconfig
+++ b/arch/arm/configs/tegra_defconfig
@@ -1,4 +1,6 @@
 CONFIG_EXPERIMENTAL=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_CGROUPS=y
@@ -25,14 +27,9 @@
 CONFIG_ARCH_TEGRA_2x_SOC=y
 CONFIG_ARCH_TEGRA_3x_SOC=y
 CONFIG_MACH_HARMONY=y
-CONFIG_MACH_KAEN=y
 CONFIG_MACH_PAZ00=y
 CONFIG_MACH_TRIMSLICE=y
-CONFIG_MACH_WARIO=y
-CONFIG_MACH_VENTANA=y
 CONFIG_TEGRA_EMC_SCALING_ENABLE=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_SMP=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
@@ -103,19 +100,24 @@
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 # CONFIG_I2C_COMPAT is not set
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PINCTRL=y
 CONFIG_I2C_TEGRA=y
 CONFIG_SPI=y
 CONFIG_SPI_TEGRA=y
+CONFIG_GPIO_TPS65910=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_BATTERY_SBS=y
 CONFIG_SENSORS_LM90=y
 CONFIG_MFD_TPS6586X=y
+CONFIG_MFD_TPS65910=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_TPS62360=y
 CONFIG_REGULATOR_TPS6586X=y
+CONFIG_REGULATOR_TPS65910=y
 CONFIG_SOUND=y
 CONFIG_SND=y
 # CONFIG_SND_SUPPORT_OLD_API is not set
@@ -126,6 +128,7 @@
 # CONFIG_SND_USB is not set
 CONFIG_SND_SOC=y
 CONFIG_SND_SOC_TEGRA=y
+CONFIG_SND_SOC_TEGRA_WM8753=y
 CONFIG_SND_SOC_TEGRA_WM8903=y
 CONFIG_SND_SOC_TEGRA_TRIMSLICE=y
 CONFIG_SND_SOC_TEGRA_ALC5632=y
diff --git a/arch/arm/mach-lpc32xx/Kconfig b/arch/arm/mach-lpc32xx/Kconfig
deleted file mode 100644
index e0b3eee..0000000
--- a/arch/arm/mach-lpc32xx/Kconfig
+++ /dev/null
@@ -1,32 +0,0 @@
-if ARCH_LPC32XX
-
-menu "Individual UART enable selections"
-
-config ARCH_LPC32XX_UART3_SELECT
-	bool "Add support for standard UART3"
-	help
-	 Adds support for standard UART 3 when the 8250 serial support
-	 is enabled.
-
-config ARCH_LPC32XX_UART4_SELECT
-	bool "Add support for standard UART4"
-	help
-	 Adds support for standard UART 4 when the 8250 serial support
-	 is enabled.
-
-config ARCH_LPC32XX_UART5_SELECT
-	bool "Add support for standard UART5"
-	default y
-	help
-	 Adds support for standard UART 5 when the 8250 serial support
-	 is enabled.
-
-config ARCH_LPC32XX_UART6_SELECT
-	bool "Add support for standard UART6"
-	help
-	 Adds support for standard UART 6 when the 8250 serial support
-	 is enabled.
-
-endmenu
-
-endif
diff --git a/arch/arm/mach-lpc32xx/Makefile.boot b/arch/arm/mach-lpc32xx/Makefile.boot
index 2cfe0ee..697323b 100644
--- a/arch/arm/mach-lpc32xx/Makefile.boot
+++ b/arch/arm/mach-lpc32xx/Makefile.boot
@@ -2,3 +2,4 @@
 params_phys-y	:= 0x80000100
 initrd_phys-y	:= 0x82000000
 
+dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
diff --git a/arch/arm/mach-lpc32xx/clock.c b/arch/arm/mach-lpc32xx/clock.c
index f6a3ffe..e8d315e 100644
--- a/arch/arm/mach-lpc32xx/clock.c
+++ b/arch/arm/mach-lpc32xx/clock.c
@@ -691,10 +691,21 @@
 	.parent		= &clk_hclk,
 	.enable		= local_onoff_enable,
 	.enable_reg	= LPC32XX_CLKPWR_NAND_CLK_CTRL,
-	.enable_mask	= LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN,
+	.enable_mask	= LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN |
+			  LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
 	.get_rate	= local_return_parent_rate,
 };
 
+static struct clk clk_nand_mlc = {
+	.parent         = &clk_hclk,
+	.enable         = local_onoff_enable,
+	.enable_reg     = LPC32XX_CLKPWR_NAND_CLK_CTRL,
+	.enable_mask    = LPC32XX_CLKPWR_NANDCLK_MLCCLK_EN |
+			  LPC32XX_CLKPWR_NANDCLK_DMA_INT |
+			  LPC32XX_CLKPWR_NANDCLK_INTSEL_MLC,
+	.get_rate       = local_return_parent_rate,
+};
+
 static struct clk clk_i2s0 = {
 	.parent		= &clk_hclk,
 	.enable		= local_onoff_enable,
@@ -707,7 +718,8 @@
 	.parent		= &clk_hclk,
 	.enable		= local_onoff_enable,
 	.enable_reg	= LPC32XX_CLKPWR_I2S_CLK_CTRL,
-	.enable_mask	= LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN,
+	.enable_mask	= LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN |
+			  LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA,
 	.get_rate	= local_return_parent_rate,
 };
 
@@ -1120,8 +1132,9 @@
 	CLKDEV_INIT("31020300.i2c", NULL, &clk_i2c2),
 	CLKDEV_INIT("dev:ssp0", NULL, &clk_ssp0),
 	CLKDEV_INIT("dev:ssp1", NULL, &clk_ssp1),
-	CLKDEV_INIT("lpc32xx_keys.0", NULL, &clk_kscan),
-	CLKDEV_INIT("lpc32xx-nand.0", "nand_ck", &clk_nand),
+	CLKDEV_INIT("40050000.key", NULL, &clk_kscan),
+	CLKDEV_INIT("20020000.flash", NULL, &clk_nand),
+	CLKDEV_INIT("200a8000.flash", NULL, &clk_nand_mlc),
 	CLKDEV_INIT("40048000.adc", NULL, &clk_adc),
 	CLKDEV_INIT(NULL, "i2s0_ck", &clk_i2s0),
 	CLKDEV_INIT(NULL, "i2s1_ck", &clk_i2s1),
diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio.h b/arch/arm/mach-lpc32xx/include/mach/gpio.h
index 2ba6ca4..0052e7a 100644
--- a/arch/arm/mach-lpc32xx/include/mach/gpio.h
+++ b/arch/arm/mach-lpc32xx/include/mach/gpio.h
@@ -3,6 +3,4 @@
 
 #include "gpio-lpc32xx.h"
 
-#define ARCH_NR_GPIOS (LPC32XX_GPO_P3_GRP + LPC32XX_GPO_P3_MAX)
-
 #endif /* __MACH_GPIO_H */
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index 540106c..c1aabfc 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -30,12 +30,13 @@
 #include <linux/amba/bus.h>
 #include <linux/amba/clcd.h>
 #include <linux/amba/pl022.h>
+#include <linux/amba/pl08x.h>
+#include <linux/amba/mmci.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/clk.h>
-#include <linux/amba/pl08x.h>
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -50,9 +51,12 @@
 /*
  * Mapped GPIOLIB GPIOs
  */
-#define SPI0_CS_GPIO	LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
-#define LCD_POWER_GPIO	LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
-#define BKL_POWER_GPIO	LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define SPI0_CS_GPIO		LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+#define LCD_POWER_GPIO		LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
+#define BKL_POWER_GPIO		LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define MMC_PWR_ENABLE_GPIO	LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 5)
+#define MMC_CD_GPIO		LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 1)
+#define MMC_WP_GPIO		LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 0)
 
 /*
  * AMBA LCD controller
@@ -158,24 +162,6 @@
 /*
  * AMBA SSP (SPI)
  */
-static void phy3250_spi_cs_set(u32 control)
-{
-	gpio_set_value(SPI0_CS_GPIO, (int) control);
-}
-
-static struct pl022_config_chip spi0_chip_info = {
-	.com_mode		= INTERRUPT_TRANSFER,
-	.iface			= SSP_INTERFACE_MOTOROLA_SPI,
-	.hierarchy		= SSP_MASTER,
-	.slave_tx_disable	= 0,
-	.rx_lev_trig		= SSP_RX_4_OR_MORE_ELEM,
-	.tx_lev_trig		= SSP_TX_4_OR_MORE_EMPTY_LOC,
-	.ctrl_len		= SSP_BITS_8,
-	.wait_state		= SSP_MWIRE_WAIT_ZERO,
-	.duplex			= SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
-	.cs_control		= phy3250_spi_cs_set,
-};
-
 static struct pl022_ssp_controller lpc32xx_ssp0_data = {
 	.bus_id			= 0,
 	.num_chipselect		= 1,
@@ -188,45 +174,57 @@
 	.enable_dma		= 0,
 };
 
-/* AT25 driver registration */
-static int __init phy3250_spi_board_register(void)
+static struct pl08x_channel_data pl08x_slave_channels[] = {
+	{
+		.bus_id = "nand-slc",
+		.min_signal = 1, /* SLC NAND Flash */
+		.max_signal = 1,
+		.periph_buses = PL08X_AHB1,
+	},
+	{
+		.bus_id = "nand-mlc",
+		.min_signal = 12, /* MLC NAND Flash */
+		.max_signal = 12,
+		.periph_buses = PL08X_AHB1,
+	},
+};
+
+/* NOTE: These will change, according to RMK */
+static int pl08x_get_signal(struct pl08x_dma_chan *ch)
 {
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-	static struct spi_board_info info[] = {
-		{
-			.modalias = "spidev",
-			.max_speed_hz = 5000000,
-			.bus_num = 0,
-			.chip_select = 0,
-			.controller_data = &spi0_chip_info,
-		},
-	};
-
-#else
-	static struct spi_eeprom eeprom = {
-		.name = "at25256a",
-		.byte_len = 0x8000,
-		.page_size = 64,
-		.flags = EE_ADDR2,
-	};
-
-	static struct spi_board_info info[] = {
-		{
-			.modalias = "at25",
-			.max_speed_hz = 5000000,
-			.bus_num = 0,
-			.chip_select = 0,
-			.mode = SPI_MODE_0,
-			.platform_data = &eeprom,
-			.controller_data = &spi0_chip_info,
-		},
-	};
-#endif
-	return spi_register_board_info(info, ARRAY_SIZE(info));
+	return ch->cd->min_signal;
 }
-arch_initcall(phy3250_spi_board_register);
+
+static void pl08x_put_signal(struct pl08x_dma_chan *ch)
+{
+}
 
 static struct pl08x_platform_data pl08x_pd = {
+	.slave_channels = &pl08x_slave_channels[0],
+	.num_slave_channels = ARRAY_SIZE(pl08x_slave_channels),
+	.get_signal = pl08x_get_signal,
+	.put_signal = pl08x_put_signal,
+	.lli_buses = PL08X_AHB1,
+	.mem_buses = PL08X_AHB1,
+};
+
+static int mmc_handle_ios(struct device *dev, struct mmc_ios *ios)
+{
+	/* Only on and off are supported */
+	if (ios->power_mode == MMC_POWER_OFF)
+		gpio_set_value(MMC_PWR_ENABLE_GPIO, 0);
+	else
+		gpio_set_value(MMC_PWR_ENABLE_GPIO, 1);
+	return 0;
+}
+
+static struct mmci_platform_data lpc32xx_mmci_data = {
+	.ocr_mask	= MMC_VDD_30_31 | MMC_VDD_31_32 |
+			  MMC_VDD_32_33 | MMC_VDD_33_34,
+	.ios_handler	= mmc_handle_ios,
+	.dma_filter	= NULL,
+	/* No DMA for now since AMBA PL080 dmaengine driver only does scatter
+	 * gather, and the MMCI driver doesn't do it this way */
 };
 
 static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
@@ -234,6 +232,8 @@
 	OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
 	OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
 	OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
+	OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd",
+		       &lpc32xx_mmci_data),
 	{ }
 };
 
@@ -241,10 +241,6 @@
 {
 	u32 tmp;
 
-	/* Setup SLC NAND controller muxing */
-	__raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
-		LPC32XX_CLKPWR_NAND_CLK_CTRL);
-
 	/* Setup LCD muxing to RGB565 */
 	tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
 		~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
@@ -264,34 +260,12 @@
 		LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
 	__raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
 
-	/* Disable IrDA pulsing support on UART6 */
-	tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
-	tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
-	__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
-	/* Enable DMA for I2S1 channel */
-	tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
-	tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
-	__raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
-
 	lpc32xx_serial_init();
 
-	/*
-	 * AMBA peripheral clocks need to be enabled prior to AMBA device
-	 * detection or a data fault will occur, so enable the clocks
-	 * here.
-	 */
-	tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
-	__raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
-		LPC32XX_CLKPWR_LCDCLK_CTRL);
-
-	tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
-	__raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
-		LPC32XX_CLKPWR_SSP_CLK_CTRL);
-
-	tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL);
-	__raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN),
-		     LPC32XX_CLKPWR_DMA_CLK_CTRL);
+	tmp = __raw_readl(LPC32XX_CLKPWR_MS_CTRL);
+	tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_EN |
+		LPC32XX_CLKPWR_MSCARD_MSDIO_PU_EN;
+	__raw_writel(tmp, LPC32XX_CLKPWR_MS_CTRL);
 
 	/* Test clock needed for UDA1380 initial init */
 	__raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
@@ -302,12 +276,10 @@
 			     lpc32xx_auxdata_lookup, NULL);
 
 	/* Register GPIOs used on this board */
-	if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
-		printk(KERN_ERR "Error requesting gpio %u",
-			SPI0_CS_GPIO);
-	else if (gpio_direction_output(SPI0_CS_GPIO, 1))
-		printk(KERN_ERR "Error setting gpio %u to output",
-			SPI0_CS_GPIO);
+	if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en"))
+		pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO);
+	else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1))
+		pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO);
 }
 
 static char const *lpc32xx_dt_compat[] __initdata = {
diff --git a/arch/arm/mach-lpc32xx/serial.c b/arch/arm/mach-lpc32xx/serial.c
index f273528..05621a2 100644
--- a/arch/arm/mach-lpc32xx/serial.c
+++ b/arch/arm/mach-lpc32xx/serial.c
@@ -31,59 +31,6 @@
 
 #define LPC32XX_SUART_FIFO_SIZE	64
 
-/* Standard 8250/16550 compatible serial ports */
-static struct plat_serial8250_port serial_std_platform_data[] = {
-#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
-	{
-		.membase        = io_p2v(LPC32XX_UART5_BASE),
-		.mapbase        = LPC32XX_UART5_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR5,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
-	{
-		.membase	= io_p2v(LPC32XX_UART3_BASE),
-		.mapbase        = LPC32XX_UART3_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR3,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
-	{
-		.membase	= io_p2v(LPC32XX_UART4_BASE),
-		.mapbase        = LPC32XX_UART4_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR4,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
-	{
-		.membase	= io_p2v(LPC32XX_UART6_BASE),
-		.mapbase        = LPC32XX_UART6_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR6,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-	{ },
-};
-
 struct uartinit {
 	char *uart_ck_name;
 	u32 ck_mode_mask;
@@ -92,7 +39,6 @@
 };
 
 static struct uartinit uartinit_data[] __initdata = {
-#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
 	{
 		.uart_ck_name = "uart5_ck",
 		.ck_mode_mask =
@@ -100,8 +46,6 @@
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL,
 		.mapbase = LPC32XX_UART5_BASE,
 	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
 	{
 		.uart_ck_name = "uart3_ck",
 		.ck_mode_mask =
@@ -109,8 +53,6 @@
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL,
 		.mapbase = LPC32XX_UART3_BASE,
 	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
 	{
 		.uart_ck_name = "uart4_ck",
 		.ck_mode_mask =
@@ -118,8 +60,6 @@
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL,
 		.mapbase = LPC32XX_UART4_BASE,
 	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
 	{
 		.uart_ck_name = "uart6_ck",
 		.ck_mode_mask =
@@ -127,19 +67,6 @@
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL,
 		.mapbase = LPC32XX_UART6_BASE,
 	},
-#endif
-};
-
-static struct platform_device serial_std_platform_device = {
-	.name			= "serial8250",
-	.id			= 0,
-	.dev			= {
-		.platform_data	= serial_std_platform_data,
-	},
-};
-
-static struct platform_device *lpc32xx_serial_devs[] __initdata = {
-	&serial_std_platform_device,
 };
 
 void __init lpc32xx_serial_init(void)
@@ -156,15 +83,8 @@
 		clk = clk_get(NULL, uartinit_data[i].uart_ck_name);
 		if (!IS_ERR(clk)) {
 			clk_enable(clk);
-			serial_std_platform_data[i].uartclk =
-				clk_get_rate(clk);
 		}
 
-		/* Fall back on main osc rate if clock rate return fails */
-		if (serial_std_platform_data[i].uartclk == 0)
-			serial_std_platform_data[i].uartclk =
-				LPC32XX_MAIN_OSC_FREQ;
-
 		/* Setup UART clock modes for all UARTs, disable autoclock */
 		clkmodes |= uartinit_data[i].ck_mode_mask;
 
@@ -189,7 +109,7 @@
 	__raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE);
 	for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) {
 		/* Force a flush of the RX FIFOs to work around a HW bug */
-		puart = serial_std_platform_data[i].mapbase;
+		puart = uartinit_data[i].mapbase;
 		__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));
 		__raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart));
 		j = LPC32XX_SUART_FIFO_SIZE;
@@ -198,11 +118,13 @@
 		__raw_writel(0, LPC32XX_UART_IIR_FCR(puart));
 	}
 
+	/* Disable IrDA pulsing support on UART6 */
+	tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
+	tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
+	__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
+
 	/* Disable UART5->USB transparent mode or USB won't work */
 	tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
 	tmp &= ~LPC32XX_UART_U5_ROUTE_TO_USB;
 	__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
-	platform_add_devices(lpc32xx_serial_devs,
-		ARRAY_SIZE(lpc32xx_serial_devs));
 }