fec: Convert printks to netdev_<level>
Use a more current logging message style.
Convert the printks where a struct net_device is available to
netdev_<level>. Convert the other printks to pr_<level> and
add pr_fmt where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 153437b..d7657a4 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -266,7 +266,7 @@
/* Ooops. All transmit buffers are full. Bail out.
* This should not happen, since ndev->tbusy should be set.
*/
- printk("%s: tx queue full!.\n", ndev->name);
+ netdev_err(ndev, "tx queue full!\n");
return NETDEV_TX_BUSY;
}
@@ -578,7 +578,7 @@
writel(1, fep->hwp + FEC_X_CNTRL); /* Graceful transmit stop */
udelay(10);
if (!(readl(fep->hwp + FEC_IEVENT) & FEC_ENET_GRA))
- printk("fec_stop : Graceful transmit stop did not complete !\n");
+ netdev_err(ndev, "Graceful transmit stop did not complete!\n");
}
/* Whack a reset. We should wait for this. */
@@ -676,7 +676,7 @@
}
if (status & BD_ENET_TX_READY)
- printk("HEY! Enet xmit interrupt and TX_READY.\n");
+ netdev_err(ndev, "HEY! Enet xmit interrupt and TX_READY\n");
/* Deferred means some collisions occurred during transmit,
* but we eventually sent the packet OK.
@@ -744,7 +744,7 @@
* the last indicator should be set.
*/
if ((status & BD_ENET_RX_LAST) == 0)
- printk("FEC ENET: rcv is not +last\n");
+ netdev_err(ndev, "rcv is not +last\n");
if (!fep->opened)
goto rx_processing_done;
@@ -1031,7 +1031,7 @@
usecs_to_jiffies(FEC_MII_TIMEOUT));
if (time_left == 0) {
fep->mii_timeout = 1;
- printk(KERN_ERR "FEC: MDIO read timeout\n");
+ netdev_err(fep->netdev, "MDIO read timeout\n");
return -ETIMEDOUT;
}
@@ -1059,7 +1059,7 @@
usecs_to_jiffies(FEC_MII_TIMEOUT));
if (time_left == 0) {
fep->mii_timeout = 1;
- printk(KERN_ERR "FEC: MDIO write timeout\n");
+ netdev_err(fep->netdev, "MDIO write timeout\n");
return -ETIMEDOUT;
}
@@ -1099,9 +1099,7 @@
}
if (phy_id >= PHY_MAX_ADDR) {
- printk(KERN_INFO
- "%s: no PHY, assuming direct connection to switch\n",
- ndev->name);
+ netdev_info(ndev, "no PHY, assuming direct connection to switch\n");
strncpy(mdio_bus_id, "fixed-0", MII_BUS_ID_SIZE);
phy_id = 0;
}
@@ -1110,7 +1108,7 @@
phy_dev = phy_connect(ndev, phy_name, &fec_enet_adjust_link,
fep->phy_interface);
if (IS_ERR(phy_dev)) {
- printk(KERN_ERR "%s: could not attach to PHY\n", ndev->name);
+ netdev_err(ndev, "could not attach to PHY\n");
return PTR_ERR(phy_dev);
}
@@ -1128,11 +1126,9 @@
fep->link = 0;
fep->full_duplex = 0;
- printk(KERN_INFO
- "%s: Freescale FEC PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
- ndev->name,
- fep->phy_dev->drv->name, dev_name(&fep->phy_dev->dev),
- fep->phy_dev->irq);
+ netdev_info(ndev, "Freescale FEC PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
+ fep->phy_dev->drv->name, dev_name(&fep->phy_dev->dev),
+ fep->phy_dev->irq);
return 0;
}