| # |
| # Multimedia Video device configuration |
| # |
| |
| menuconfig RADIO_ADAPTERS |
| bool "Radio Adapters" |
| depends on VIDEO_V4L2 |
| depends on MEDIA_RADIO_SUPPORT |
| default y |
| ---help--- |
| Say Y here to enable selecting AM/FM radio adapters. |
| |
| if RADIO_ADAPTERS && VIDEO_V4L2 |
| |
| config RADIO_TEA575X |
| tristate |
| |
| config RADIO_SI470X |
| bool "Silicon Labs Si470x FM Radio Receiver support" |
| depends on VIDEO_V4L2 |
| |
| source "drivers/media/radio/si470x/Kconfig" |
| |
| config RADIO_SI476X |
| tristate "Silicon Laboratories Si476x I2C FM Radio" |
| depends on I2C && VIDEO_V4L2 |
| depends on MFD_SI476X_CORE |
| depends on SND_SOC |
| select SND_SOC_SI476X |
| ---help--- |
| Choose Y here if you have this FM radio chip. |
| |
| In order to control your radio card, you will need to use programs |
| that are compatible with the Video For Linux 2 API. Information on |
| this API and pointers to "v4l2" programs may be found at |
| <file:Documentation/video4linux/API.html>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-si476x. |
| |
| config USB_MR800 |
| tristate "AverMedia MR 800 USB FM radio support" |
| depends on USB && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to connect this type of radio to your |
| computer's USB port. Note that the audio is not digital, and |
| you must connect the line out connector to a sound card or a |
| set of speakers. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-mr800. |
| |
| config USB_DSBR |
| tristate "D-Link/GemTek USB FM radio support" |
| depends on USB && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to connect this type of radio to your |
| computer's USB port. Note that the audio is not digital, and |
| you must connect the line out connector to a sound card or a |
| set of speakers. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called dsbr100. |
| |
| config RADIO_MAXIRADIO |
| tristate "Guillemot MAXI Radio FM 2000 radio" |
| depends on VIDEO_V4L2 && PCI |
| select RADIO_TEA575X |
| ---help--- |
| Choose Y here if you have this radio card. This card may also be |
| found as Gemtek PCI FM. |
| |
| In order to control your radio card, you will need to use programs |
| that are compatible with the Video For Linux API. Information on |
| this API and pointers to "v4l" programs may be found at |
| <file:Documentation/video4linux/API.html>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-maxiradio. |
| |
| config RADIO_SHARK |
| tristate "Griffin radioSHARK USB radio receiver" |
| depends on USB |
| select RADIO_TEA575X |
| ---help--- |
| Choose Y here if you have this radio receiver. |
| |
| There are 2 versions of this device, this driver is for version 1, |
| which is white. |
| |
| In order to control your radio card, you will need to use programs |
| that are compatible with the Video For Linux API. Information on |
| this API and pointers to "v4l" programs may be found at |
| <file:Documentation/video4linux/API.html>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-shark. |
| |
| config RADIO_SHARK2 |
| tristate "Griffin radioSHARK2 USB radio receiver" |
| depends on USB |
| ---help--- |
| Choose Y here if you have this radio receiver. |
| |
| There are 2 versions of this device, this driver is for version 2, |
| which is black. |
| |
| In order to control your radio card, you will need to use programs |
| that are compatible with the Video For Linux API. Information on |
| this API and pointers to "v4l" programs may be found at |
| <file:Documentation/video4linux/API.html>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-shark2. |
| |
| config I2C_SI4713 |
| tristate "I2C driver for Silicon Labs Si4713 device" |
| depends on I2C && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want support to Si4713 I2C device. |
| This device driver supports only i2c bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called si4713. |
| |
| config RADIO_SI4713 |
| tristate "Silicon Labs Si4713 FM Radio Transmitter support" |
| depends on I2C && VIDEO_V4L2 |
| select I2C_SI4713 |
| ---help--- |
| Say Y here if you want support to Si4713 FM Radio Transmitter. |
| This device can transmit audio through FM. It can transmit |
| RDS and RBDS signals as well. This module is the v4l2 radio |
| interface for the i2c driver of this device. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-si4713. |
| |
| config USB_KEENE |
| tristate "Keene FM Transmitter USB support" |
| depends on USB && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to connect this type of FM transmitter |
| to your computer's USB port. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-keene. |
| |
| config USB_MA901 |
| tristate "Masterkit MA901 USB FM radio support" |
| depends on USB && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to connect this type of radio to your |
| computer's USB port. Note that the audio is not digital, and |
| you must connect the line out connector to a sound card or a |
| set of speakers or headphones. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-ma901. |
| |
| config RADIO_TEA5764 |
| tristate "TEA5764 I2C FM radio support" |
| depends on I2C && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to use the TEA5764 FM chip found in |
| EZX phones. This FM chip is present in EZX phones from Motorola, |
| connected to internal pxa I2C bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-tea5764. |
| |
| config RADIO_TEA5764_XTAL |
| bool "TEA5764 crystal reference" |
| depends on RADIO_TEA5764=y |
| default y |
| help |
| Say Y here if TEA5764 have a 32768 Hz crystal in circuit, say N |
| here if TEA5764 reference frequency is connected in FREQIN. |
| |
| config RADIO_SAA7706H |
| tristate "SAA7706H Car Radio DSP" |
| depends on I2C && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to use the SAA7706H Car radio Digital |
| Signal Processor, found for instance on the Russellville development |
| board. On the russellville the device is connected to internal |
| timberdale I2C bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called SAA7706H. |
| |
| config RADIO_TEF6862 |
| tristate "TEF6862 Car Radio Enhanced Selectivity Tuner" |
| depends on I2C && VIDEO_V4L2 |
| ---help--- |
| Say Y here if you want to use the TEF6862 Car Radio Enhanced |
| Selectivity Tuner, found for instance on the Russellville development |
| board. On the russellville the device is connected to internal |
| timberdale I2C bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called TEF6862. |
| |
| config RADIO_TIMBERDALE |
| tristate "Enable the Timberdale radio driver" |
| depends on MFD_TIMBERDALE && VIDEO_V4L2 |
| depends on I2C # for RADIO_SAA7706H |
| select RADIO_TEF6862 |
| select RADIO_SAA7706H |
| ---help--- |
| This is a kind of umbrella driver for the Radio Tuner and DSP |
| found behind the Timberdale FPGA on the Russellville board. |
| Enabling this driver will automatically select the DSP and tuner. |
| |
| config RADIO_WL1273 |
| tristate "Texas Instruments WL1273 I2C FM Radio" |
| depends on I2C && VIDEO_V4L2 && GENERIC_HARDIRQS |
| select MFD_CORE |
| select MFD_WL1273_CORE |
| select FW_LOADER |
| ---help--- |
| Choose Y here if you have this FM radio chip. |
| |
| In order to control your radio card, you will need to use programs |
| that are compatible with the Video For Linux 2 API. Information on |
| this API and pointers to "v4l2" programs may be found at |
| <file:Documentation/video4linux/API.html>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-wl1273. |
| |
| # TI's ST based wl128x FM radio |
| source "drivers/media/radio/wl128x/Kconfig" |
| |
| # |
| # ISA drivers configuration |
| # |
| |
| menuconfig V4L_RADIO_ISA_DRIVERS |
| bool "ISA radio devices" |
| depends on ISA |
| default n |
| ---help--- |
| Say Y here to enable support for these ISA drivers. |
| |
| if V4L_RADIO_ISA_DRIVERS |
| |
| config RADIO_ISA |
| depends on ISA |
| tristate |
| |
| config RADIO_CADET |
| tristate "ADS Cadet AM/FM Tuner" |
| depends on ISA && VIDEO_V4L2 |
| ---help--- |
| Choose Y here if you have one of these AM/FM radio cards, and then |
| fill in the port address below. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-cadet. |
| |
| config RADIO_RTRACK |
| tristate "AIMSlab RadioTrack (aka RadioReveal) support" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have one of these FM radio cards, and then fill |
| in the port address below. |
| |
| Note that newer AIMSlab RadioTrack cards have a different chipset |
| and are not supported by this driver. For these cards, use the |
| RadioTrack II driver below. |
| |
| If you have a GemTeks combined (PnP) sound- and radio card you must |
| use this driver as a module and setup the card with isapnptools. |
| You must also pass the module a suitable io parameter, 0x248 has |
| been reported to be used by these cards. |
| |
| More information is contained in the file |
| <file:Documentation/video4linux/radiotrack.txt>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-aimslab. |
| |
| config RADIO_RTRACK_PORT |
| hex "RadioTrack i/o port (0x20f or 0x30f)" |
| depends on RADIO_RTRACK=y |
| default "30f" |
| help |
| Enter either 0x30f or 0x20f here. The card default is 0x30f, if you |
| haven't changed the jumper setting on the card. |
| |
| config RADIO_RTRACK2 |
| tristate "AIMSlab RadioTrack II support" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have this FM radio card, and then fill in the |
| port address below. |
| |
| Note: this driver hasn't been tested since a long time due to lack |
| of hardware. If you have this hardware, then please contact the |
| linux-media mailinglist. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-rtrack2. |
| |
| config RADIO_RTRACK2_PORT |
| hex "RadioTrack II i/o port (0x20c or 0x30c)" |
| depends on RADIO_RTRACK2=y |
| default "30c" |
| help |
| Enter either 0x30c or 0x20c here. The card default is 0x30c, if you |
| haven't changed the jumper setting on the card. |
| |
| config RADIO_AZTECH |
| tristate "Aztech/Packard Bell Radio" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have one of these FM radio cards, and then fill |
| in the port address below. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-aztech. |
| |
| config RADIO_AZTECH_PORT |
| hex "Aztech/Packard Bell I/O port (0x350 or 0x358)" |
| depends on RADIO_AZTECH=y |
| default "350" |
| help |
| Enter either 0x350 or 0x358 here. The card default is 0x350, if you |
| haven't changed the setting of jumper JP3 on the card. Removing the |
| jumper sets the card to 0x358. |
| |
| config RADIO_GEMTEK |
| tristate "GemTek Radio card (or compatible) support" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have this FM radio card, and then fill in the |
| I/O port address and settings below. The following cards either have |
| GemTek Radio tuner or are rebranded GemTek Radio cards: |
| |
| - Sound Vision 16 Gold with FM Radio |
| - Typhoon Radio card (some models) |
| - Hama Radio card |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-gemtek. |
| |
| config RADIO_GEMTEK_PORT |
| hex "Fixed I/O port (0x20c, 0x30c, 0x24c, 0x34c, 0x248 or 0x28c)" |
| depends on RADIO_GEMTEK=y |
| default "34c" |
| help |
| Enter either 0x20c, 0x30c, 0x24c, 0x34c, 0x248 or 0x28c here. The |
| card default is 0x34c, if you haven't changed the jumper setting |
| on the card. |
| |
| On Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O |
| port is 0x20c, 0x248 or 0x28c. |
| |
| If automatic I/O port probing is enabled this port will be used only |
| in case of automatic probing failure, ie. as a fallback. |
| |
| config RADIO_GEMTEK_PROBE |
| bool "Automatic I/O port probing" |
| depends on RADIO_GEMTEK=y |
| default y |
| help |
| Say Y here to enable automatic probing for GemTek Radio card. The |
| following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and |
| 0x28c. |
| |
| config RADIO_MIROPCM20 |
| tristate "miroSOUND PCM20 radio" |
| depends on ISA && ISA_DMA_API && VIDEO_V4L2 && SND |
| select SND_ISA |
| select SND_MIRO |
| ---help--- |
| Choose Y here if you have this FM radio card. You also need to enable |
| the ALSA sound system. This choice automatically selects the ALSA |
| sound card driver "Miro miroSOUND PCM1pro/PCM12/PCM20radio" as this |
| is required for the radio-miropcm20. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-miropcm20. |
| |
| config RADIO_SF16FMI |
| tristate "SF16-FMI/SF16-FMP/SF16-FMD Radio" |
| depends on ISA && VIDEO_V4L2 |
| ---help--- |
| Choose Y here if you have one of these FM radio cards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-sf16fmi. |
| |
| config RADIO_SF16FMR2 |
| tristate "SF16-FMR2/SF16-FMD2 Radio" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_TEA575X |
| ---help--- |
| Choose Y here if you have one of these FM radio cards. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-sf16fmr2. |
| |
| config RADIO_TERRATEC |
| tristate "TerraTec ActiveRadio ISA Standalone" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have this FM radio card. |
| |
| Note: this driver hasn't been tested since a long time due to lack |
| of hardware. If you have this hardware, then please contact the |
| linux-media mailinglist. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-terratec. |
| |
| config RADIO_TRUST |
| tristate "Trust FM radio card" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| help |
| This is a driver for the Trust FM radio cards. Say Y if you have |
| such a card and want to use it under Linux. |
| |
| Note: this driver hasn't been tested since a long time due to lack |
| of hardware. If you have this hardware, then please contact the |
| linux-media mailinglist. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-trust. |
| |
| config RADIO_TRUST_PORT |
| hex "Trust i/o port (usually 0x350 or 0x358)" |
| depends on RADIO_TRUST=y |
| default "350" |
| help |
| Enter the I/O port of your Trust FM radio card. If unsure, try the |
| values "0x350" or "0x358". |
| |
| config RADIO_TYPHOON |
| tristate "Typhoon Radio (a.k.a. EcoRadio)" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have one of these FM radio cards, and then fill |
| in the port address and the frequency used for muting below. |
| |
| Note: this driver hasn't been tested since a long time due to lack |
| of hardware. If you have this hardware, then please contact the |
| linux-media mailinglist. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-typhoon. |
| |
| config RADIO_TYPHOON_PORT |
| hex "Typhoon I/O port (0x316 or 0x336)" |
| depends on RADIO_TYPHOON=y |
| default "316" |
| help |
| Enter the I/O port of your Typhoon or EcoRadio radio card. |
| |
| config RADIO_TYPHOON_MUTEFREQ |
| int "Typhoon frequency set when muting the device (kHz)" |
| depends on RADIO_TYPHOON=y |
| default "87500" |
| help |
| Enter the frequency used for muting the radio. The device is never |
| completely silent. If the volume is just turned down, you can still |
| hear silent voices and music. For that reason, the frequency of the |
| radio device is set to the frequency you can enter here whenever |
| the device is muted. There should be no local radio station at that |
| frequency. |
| |
| config RADIO_ZOLTRIX |
| tristate "Zoltrix Radio" |
| depends on ISA && VIDEO_V4L2 |
| select RADIO_ISA |
| ---help--- |
| Choose Y here if you have one of these FM radio cards, and then fill |
| in the port address below. |
| |
| Note: this driver hasn't been tested since a long time due to lack |
| of hardware. If you have this hardware, then please contact the |
| linux-media mailinglist. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called radio-zoltrix. |
| |
| config RADIO_ZOLTRIX_PORT |
| hex "ZOLTRIX I/O port (0x20c or 0x30c)" |
| depends on RADIO_ZOLTRIX=y |
| default "20c" |
| help |
| Enter the I/O port of your Zoltrix radio card. |
| |
| endif # V4L_RADIO_ISA_DRIVERS |
| |
| endif # RADIO_ADAPTERS |