sky2: receive checksum refactoring
Break the largish case for handling receive checksum into a separate
function, and if there is a problem use dev_XXX routines to
show which hardware is the problem.
Turn one corner case into a BUG(). This only happens if the driver
is expecting one behavior but the chip does the old behavior;
only ever saw this when bringing up a new chip type and driver
was buggy.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 1aa1f33..478288b 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -2484,6 +2484,32 @@
}
}
+static void sky2_rx_checksum(struct sky2_port *sky2, u32 status)
+{
+ /* If this happens then driver assuming wrong format for chip type */
+ BUG_ON(sky2->hw->flags & SKY2_HW_NEW_LE);
+
+ /* Both checksum counters are programmed to start at
+ * the same offset, so unless there is a problem they
+ * should match. This failure is an early indication that
+ * hardware receive checksumming won't work.
+ */
+ if (likely((u16)(status >> 16) == (u16)status)) {
+ struct sk_buff *skb = sky2->rx_ring[sky2->rx_next].skb;
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ skb->csum = le16_to_cpu(status);
+ } else {
+ dev_notice(&sky2->hw->pdev->dev,
+ "%s: receive checksum problem (status = %#x)\n",
+ sky2->netdev->name, status);
+
+ /* Disable checksum offload */
+ sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM;
+ sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
+ BMU_DIS_RX_CHKSUM);
+ }
+}
+
/* Process status response ring */
static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx)
{
@@ -2552,37 +2578,8 @@
/* fall through */
#endif
case OP_RXCHKS:
- if (!(sky2->flags & SKY2_FLAG_RX_CHECKSUM))
- break;
-
- /* If this happens then driver assuming wrong format */
- if (unlikely(hw->flags & SKY2_HW_NEW_LE)) {
- if (net_ratelimit())
- printk(KERN_NOTICE "%s: unexpected"
- " checksum status\n",
- dev->name);
- break;
- }
-
- /* Both checksum counters are programmed to start at
- * the same offset, so unless there is a problem they
- * should match. This failure is an early indication that
- * hardware receive checksumming won't work.
- */
- if (likely(status >> 16 == (status & 0xffff))) {
- skb = sky2->rx_ring[sky2->rx_next].skb;
- skb->ip_summed = CHECKSUM_COMPLETE;
- skb->csum = le16_to_cpu(status);
- } else {
- printk(KERN_NOTICE PFX "%s: hardware receive "
- "checksum problem (status = %#x)\n",
- dev->name, status);
- sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM;
-
- sky2_write32(sky2->hw,
- Q_ADDR(rxqaddr[port], Q_CSR),
- BMU_DIS_RX_CHKSUM);
- }
+ if (likely(sky2->flags & SKY2_FLAG_RX_CHECKSUM))
+ sky2_rx_checksum(sky2, status);
break;
case OP_TXINDEXLE: