bnx2x: Control number of vfs dynamically
1. Support sysfs interface for getting the maximal number of virtual functions
of a given physical function.
2. Support sysfs interface for getting and setting the current number of
virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 9be9b03..f685d2e 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -9546,8 +9546,10 @@
/* enable SR-IOV if applicable */
if (IS_SRIOV(bp) && test_and_clear_bit(BNX2X_SP_RTNL_ENABLE_SRIOV,
- &bp->sp_rtnl_state))
+ &bp->sp_rtnl_state)) {
+ bnx2x_disable_sriov(bp);
bnx2x_enable_sriov(bp);
+ }
}
static void bnx2x_period_task(struct work_struct *work)
@@ -11423,26 +11425,6 @@
* net_device service functions
*/
-static int bnx2x_open_epilog(struct bnx2x *bp)
-{
- /* Enable sriov via delayed work. This must be done via delayed work
- * because it causes the probe of the vf devices to be run, which invoke
- * register_netdevice which must have rtnl lock taken. As we are holding
- * the lock right now, that could only work if the probe would not take
- * the lock. However, as the probe of the vf may be called from other
- * contexts as well (such as passthrough to vm failes) it can't assume
- * the lock is being held for it. Using delayed work here allows the
- * probe code to simply take the lock (i.e. wait for it to be released
- * if it is being held).
- */
- smp_mb__before_clear_bit();
- set_bit(BNX2X_SP_RTNL_ENABLE_SRIOV, &bp->sp_rtnl_state);
- smp_mb__after_clear_bit();
- schedule_delayed_work(&bp->sp_rtnl_task, 0);
-
- return 0;
-}
-
/* called with rtnl_lock */
static int bnx2x_open(struct net_device *dev)
{
@@ -12498,13 +12480,8 @@
goto init_one_exit;
}
- /* Enable SRIOV if capability found in configuration space.
- * Once the generic SR-IOV framework makes it in from the
- * pci tree this will be revised, to allow dynamic control
- * over the number of VFs. Right now, change the num of vfs
- * param below to enable SR-IOV.
- */
- rc = bnx2x_iov_init_one(bp, int_mode, 0/*num vfs*/);
+ /* Enable SRIOV if capability found in configuration space */
+ rc = bnx2x_iov_init_one(bp, int_mode, BNX2X_MAX_NUM_OF_VFS);
if (rc)
goto init_one_exit;
@@ -12820,6 +12797,9 @@
.suspend = bnx2x_suspend,
.resume = bnx2x_resume,
.err_handler = &bnx2x_err_handler,
+#ifdef CONFIG_BNX2X_SRIOV
+ .sriov_configure = bnx2x_sriov_configure,
+#endif
};
static int __init bnx2x_init(void)